OTA105102 OptiX OSN 2500 Hardware Description ISSUE 1.20

Internal
OTA105102 OptiX OSN 2500

Hardware Description
ISSUE 1.20 www.huawei.com
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved

Upon completion of this course, you will be able to:
 Appreciate the networking applications of the Opti
X OSN 2500
 Describe the system structure and features of the
OptiX OSN 2500
 Describe the main functions of the boards used o
n the OptiX OSN 2500
 Outline the system protection schemes of the Opt
iX OSN 2500
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 2

Chapter 1 Product Introduction
Chapter 2 Cabinet, Sub-rack and Boards
Chapter 3 Features

Introduction
What is OSN 2500 ?
 Full name: OptiX OSN 2500 intelligent optical switching system

 Forms part of the OptiX OSN NG-SDH Series
 Optical convergence or access switching system
 OSN: Optical Switch Node

Network Application
4010G 160  10G
Long-Haul
Back Bone
OptiX BWS 1600G OptiX BWS 1600G
iManager T2000
R
10G/2.5G 10G 10G/2.5G Core
OSN
OSN 9500/7500/3500 OSN 9500/7500
9500/7500/3500
Convergence
OSN 2500 /1500 OSN 3500/ 2500 OSN 3500/ 2500
OSN 1500/Metro OSN 2500 /Metro OSN 1500/Metro Access

System Architecture
System architecture of OptiX OSN 2500
STM-1 LU LU STM-16
STM-4 Cross-connect Unit

LU LU λ
High-order matrix
(VC-4)
Low-order matrix
(VC-12/VC-3)
PDH TU TU SAN/
Video
Ethernet TU TU ATM
External Timing Auxiliary Management

SCC Unit
synchronization Unit Unit Auxiliary interface
interface interface

Large capacity and multi-services access
Large and multi-
services access
capacity
STM-1/4/16 STM-1/4/16
VC-4-4c/ SDH unit SDH unit
VC-4-4c/
8c/16c 8c/16c
West East
Cross-connect matrix higher-order

(60G) lower-order (20G)
Large cross-
Multi-granularity
connect capacity
cross-connect
capacity
PDH Ethernet Other
Interface Interface Interface
unit unit unit
E1/T1/E3/T3/E4 FE/GE ATM

Chapter 3 Features

Cabinet
ETSI 300/600 Cabinet Weight Max. number of

(mm) (kg) mounted sub-racks
600 (W) x 300 (D) x 2000 (H) 55 2

600 (W) x 600 (D) x 2000 (H) 79 2
600 (W) x 300 (D) x 2200 (H) 60 3
600 (W) x 600 (D) x 2200 (H) 84 3
600 (W) x 300 (D) x 2600 (H) 70 4
600 (W) x 600 (D) x 2600 (H) 94 4
W D

Indicators and Power Consumption
Cabinet Indicators
Indicator Color Status Description PowerCritical MajorMinor
On Cabinet is powered ON Power distribution unit

Power
Off Cabinet is OFF
On Critical alarm
Critical alarm
Off No critical alarm
On Major alarm
Major alarm
Off No major alarm
On Minor alarm
Minor alarm
Off No minor alarm
Note:
 Indicators do not flash
 If alarm indicator is ON, alarm occurs on one or more sub-racks inside Power Fuse
the cabinet consumption/
capacity/
 Alarms occur on sub-racks, ALM cable should be properly connected sub-rack
(W) sub-rack (A)
Power Consumption and Fuse 400 15

Power Distribution Unit
1 2 3 4 5 6
1 2 3
OUTPUT
4
A B 1 2 3
OUTPUT
4
ON ON
RTN1(+) RTN2(+) NEG1(-) NEG2(-)
OFF OFF
INPUT
32A 32A 20A 20A 32A 32A 20A 20A
1. Power socket (left) 2. Power cable RTN1(+) 3. Power cable RTN2(+)

4. Power cable NEG1(–) 5. Power cable NEG2(–) 6. Power socket (right)
A: Supply for Left Power interface From Left, the 1st switch supplies the lower sub-rack
B: Supply for Right Power interface The 1st & 2nd switches are mainly for OptiX OSN 7500/3500

Chapter 3 Features

Sub-rack
SEI (Auxiliary Unit)
Service slot area
Interface slot area
Core Unit
SAP (Auxiliary Unit)
PIU
FAN Unit
Dimensions (mm) 447 (W) x 295 (D) x 472 (H)
Weight (kg) 17 (not including boards and fans)

Sub-rack
Slot Assignment, Relation & Capacity
6 1, 2
S S S S S S S S S
7 3, 4 L L L L L L L L L
O O O O O O O O O
S S S S S SS S S
T T T T T T T T T
L L L L L LL L L
5 6 7 8 9 10 11 12 13
O O O O O OO O O
12 15, 16 T T T T
2 2 2 2 2 2 2 2 2
T TT T T
1 2 3 4 14 1516 17 18
. . . . . . . . .
13 17, 18 5 5 5 5 5 5 5 5 5
G G G G G G G G G
Fiber routing panel

SLOT 22 SLOT 23 SLOT 24 SLOT 25
PIU FAN FAN PIU

S S S
Sub-rack L L L
O O O
T T T S S S
19 20 21 S S S S
Slot access capacity S SSS
L
L L
O O
L L L
L
O S SSS
622 622 1.25 O O O O
L L L L M M G T T T L L L L
T T T T
O OO O 9 10 14 O OO O
S S S 8 11 12 13
T TT T L L L T TT T
1 2 3 4 O O O 2.5 2.5 S 15161718
2.5 2.5 2.5 1.25
T T T G G A
5 6 7
G G G G
P
622 622 1.25
S S M M G
S S S
L L S S S SS Fiber routing panel
L L L
O O L L L LL 22 SLOT 23 SLOT 24 25
S SS S O O O S SS S
T T O O O OO PIU FAN FAN PIU
L LL L T T T L LL L
5 6 T T T TT
O OO O 9 10 14 O O O O
7 8 11 12
13
TTTT TTT T
6 6 6 2
1 23 4 2.5 2.5 S 15161718
2 2 2.5 2.5 2.5 2.5 1.25
G G A
it
2 2 G G G G G
P 20 1
l
M M
Fiber routing panel

sp
22 SLOT 23 SLOT 24 25 7 4
PIU FAN FAN PIU
21 3

2.1 SDH unit
2.2 PDH unit
2.3 Ethernet unit
2.4 Core unit
2.5 Auxiliary unit

Boards
 Board Appearance and type
 Processing with Interface
 Processing
 Interface

SDH Unit
Connector
Board Full name Slots Available Module available
type
1 x STM-16 processing with Fixed wavelength output
SF16 Ve-16.2c, Ve-16.2d, Ve-16.2f
optical interface board (FEC)
7, 8, 11 ~ 13 Fixed wavelength output, I-16, S-

SL16 1 x STM-16 processing with 16.1, L-16.1, L-16.2, L-16.2Je, V-
(A) optical interface board 16.2Je (with BA), U-16.2Je (with
BA and PA)
LC
4 x STM-4/1 processing with
SLQ41
optical interface board
2 x STM-4 processing with I-1, S-1.1, L-1.1, L-1.2, Ve-1.2
SLD4 5 ~ 8, 11 ~ 13 I-4, S-4.1, L-4.1, L-4.2, Ve-4.2
1 x STM-4 processing with
SL4
 Signal processing with optical interface board

SDH Unit
SF16
CLASS 1 STAT
LASER ACT
PRODUCT 44 indicators
indicators
PROG
SRV
CLASS 1
LASER
PRODUCT
LC
LC Connector
Connector
Indicator Status Color Description OUT
On, green Board works normally.

STAT
On, red Board hardware fails.
IN
Board
Status
Off Board is powered off.
ACT On, green Board is activated/configured.
Board Off Board is not
Activation activated/configured. SF16

SDH Unit
Indicator description
Indicator Status Color Description

Upload of board software to FLASH or the FPGA
On, green upload is normal, or the board software
initialization is normal.
On for 100ms and off for Board software is being uploaded to FLASH or
PROG 100ms alternatively, green FGPA.
Board On for 300ms and off for Board software is initializing, and is in BIOS boot
Software 300ms alternatively, green stage.
Board software in FLASH or the FPGA
On, red configuration is lost, resulting in upload and
initialization failure.
Off No power supply.
On, green Service is normal and no service alarm occurs.
SRV
On, red Critical or major alarm occurs to service.
Service On, yellow Minor or remote alarm occurs to service.
Alarm
Off No service configured or no power supply.

SDH Unit
SL16 SL16A SL Q 4 SLD4 SL4
STAT STAT STAT STAT STAT
ACT ACT ACT ACT ACT
PROG PROG PROG PROG PROG
SRV SRV
SRV SRV SRV
SFP
SFP Module
Module
CLASS1 CLASS1
LASER LASER CLASS1
PRODUCT PRODUCT LASER
CLASS 1 CLASS 1 PRODUCT
LASER LASER
PRODUCT PRODUCT
OUT
O U T 1IN 1
O U T 1 IN 1
IN
O U T 2IN 2
O U T 2IN 2
OUT OUT
O U T 3IN 3
CLASS 1
LASER
PRODUCT IN IN
O U T 4IN 4
SL16 SL16A SLQ4 SLD4 S L4

SDH Unit
CC
Functions of SL16 d to
S
S en
Collect Alarm and
performance
Send to Cross-connect unit

16
X
VC4
……
STM-16
e ssing
proc
AU -PTR
a nd
OH

SDH Unit
Features of SL16
 Fixed wavelength output

 Automatic laser shutdown (ALS) function
 Swappable optical module (SFP)
 Support VC-4-4c, VC-4-8C and AU-4-16c
services
 Inloop and outloop function
 Setting and querying of the REG working 1 Last six digits of BOM
2 Internal number
mode 3 Board version
4 Board name
5 Board characteristic number

SDH Unit
Optical port parameters of SL16
U-16.2Je
Optical interface type I-16 S-16.1 L-16.1 L-16.2 L-16.2Je V-16.2Je
(BA+PA)
(Board characteristic #) (01) (02) (03) (04) (02) (BA) (03)
(04)
Wavelength (nm) 1310 1310 1310 1550 1550 1550 1550.12
2～ 15 ～ 40 ～
Distance (km) 0～2 80 ～ 100 80 ～ 140 140 ～ 170
15 40 80
Launched power (dBm) -10~-3 -5~0 -2~3 -2~3 5~7 14 17
Receiver sensitivity (dBm) -18 -18 -27 -28 -28 -28 -34
Receiver overload (dBm) -3 0 -9 -9 -9 -9 -10

SDH Unit
Common alarms of SDH unit
Alarm Color Alarm name Alarm reason
level
Critical R_LOS Receiver can not receive STM-N signal normally.
MS_AIS Critical alarm e.g. R_LOS happens.
Critical alarm e.g. R_LOS happens.
AU_AIS Wrong service configuration
Major
Faulty SDH board
POWER_
Power module of the line board fails.
ABNORMAL
Opposite station receives the R_LOS, R_LOF or
MS_AIS signal
MS_RDI
Faulty receiver at the opposite node or transmitter at
the local node
Minor Opposite node receives such alarms as AU_AIS and
AU_LOP.
HP_RDI
Faulty receiver at the opposite node or transmitter at
the local node
LOOP_ALM Software inloop or outloop is being performed.

SDH Unit
Common performance events of SDH
unit
Performance name Performance meaning
RSBBE Regenerator section block of background error
MSBBE Multiplex section block of background error
MSFEBBE Multiplex section far end block of background error
HPBBE High-order path block of background error
HPFEBBE High-order path far end block of background error
AUPJCHIGH Count of positive AU pointer justifications
AUPJCLOW Count of negative AU pointer justifications
RPLCUR Current value of input optical power
RPLMAX Maximum value of input optical power
RPLMIN Minimum value of input optical power
TPLCUR Current value of output optical power
TPLMAX Maximum value of output optical power
TPLMIN Minimum value of output optical power

SDH Unit
Slots Connector
Board Full name Module available
available type
2 x STM-4 processing
R1SLD4 with optical interface 7, 21
board I-4, S-4.1, L-4.1, L-4.2,
Ve-4.2
STM-4 processing with
R1SL4
LC
4 x STM-1 processing
R1SLQ1 with optical interface 5 ~ 7,19 ~ 21
board I-1, S-1.1, L-1.1, L-1.2,
Ve-1.2
STM-1 processing with
R1SL1
 Signal processing with optical interface board

SDH Unit
SFP
SFP Module
Module
R1SLQ1 R1SL1
CLASS 1
R1SLD4 R1SL4
STAT STAT
LASER
STAT STAT
ACT ACT ACT ACT PRODUCT
PROG PROG PROG
PROG
SRV SRV SRV
SRV
O U T 1IN 1 O U T 2IN 2 O U T 3IN 3 O U T 4 IN 4

O U T 1IN 1 O U T 2IN 2
O U TIN
O U T IN
R1SL4 R1SLQ1 R1SL1

R1SLD4

2.1 SDH unit
2.2 PDH unit
2.3 Ethernet unit
2.4 Core unit
2.5 Auxiliary unit

PDH Unit
Board Full name Slots available Connector type
SPQ4 4 x E4/STM-1 processing board
PD3 6 x E3/T3 processing board 6, 7, 12, 13 -
PL3 3 x E3/T3 processing board
3 x E3/T3 processing with electrical

PL3A 5 ~ 8, 11 ~ 13
interface board
MU04 4 x E4/STM-1e signal access board
6 x E3/T3 signal access bridging and SMB
D34S
switching board 1, 3, 15, 17
3 x E3/T3 signal access bridging and
C34S
switching board

PDH Unit
PL3A D34S C34S
PD3 PL3
STAT
STAT STAT ACT
ACT ACT PROG
PROG PROG SRV
SRV SRV
SMB
SMB connector
connector
Indicators
Indicators
O U T 1IN 1 O U T 2IN 2 O U T 3IN 3 O U T 4 I N 4 O U T 5I N 5 O U T 6I N 6
O U T 1 I N 1 O U T 2I N 2 O U T 3I N 3
O U T 1I N 1 O U T 2I N 2 O U T 3 I N 3
PD3 PL3 PL3A D34S C34S

PDH Unit
Slots Connector
Board Full name
available type
PQM 63 x E1/T1 signal processing board

5 ~ 7, 12, 13
PQ1 63 x E1 signal processing board -
PD1 32 x E1/T1 signal processing board 5 ~ 7, 19 ~ 21

D75S 32 x 75 Ω E1 signal access bridging and switching board
32 x 120 Ω E1/100 Ω T1 signal access bridging and switching
D12S 1 ~ 4, 15 ~ 18 DB44
board
D12B 32 x 120 Ω E1/100 Ω T1 signal access bridging board

PDH Unit
PQM D7 5S D12S D1 2 B
PQ 1
STAT
STAT ACT
ACT PROG
PROG SRV
SRV
1～8
1～8
1～8
Indicators
Indicators
9～16
9～16
9～16
PD1
STAT
17～24
ACT
17～24
17～24
PROG
SRV
DB44
DB44
25～32
25～32
25～32
D1 2 B
P Q1 PQM D 7 5S D 12 S

PDH Unit
CC
Functions of PQ1 d to
S
S en
Collect Alarm and
performance

1×VC4
63
X
E1
……
e ssing
R proc
d TU -P T
H an
LPO

PDH Unit
Features of PQ1
 Interface Type: 75Ω or 120Ω

 Support Inloop and outloop functions
 Support Warm and Cold reset
 Support TPS function

PDH Unit
Common alarms of PDH unit
Alarm
Color Alarm name Alarm reason
level
The interface board and the processing
ALM_SUBCARD_ABN
board are mismatched
T_ALOS No E1 service is accessed
Major
Critical alarm e.g. R-LOS happens
TU_AIS Wrong service configuration
Faulty PDH board
Opposite node receives such alarms as
LP_RDI
Minor TU_AIS and TU_LOP
LP_REI LPBBE happens on the opposite node

PDH Unit
Common performance of PDH unit
LPBBE Low-order path block of background error
LPFEBBE Low-order path far end block of background error
LPES Low-order path errored second
LPFEES Low-order path far end errored second
TUPJCHIGH Count of positive TU pointer justifications
TUPJCLOW Count of negative TU pointer justifications

2.1 SDH unit
2.2 PDH unit
2.3 Ethernet unit
2.4 Core unit
2.5 Auxiliary unit

Ethernet Unit
Connector
Board Full name Slots available Interface type
type
4 x GE with L2 switching
EGS4 processing with interface 1000BASE-SX/LX/ZX LC
board
2 x GE with L2 switching
EGS2 processing with interface 1000BASE-SX/LX/ZX LC
board
5 ~ 8, 11 ~ 13
2 x GE transparent
EGT2 transmission processing 1000BASE-SX/LX/ZX LC
with interface board
4 GE + 16 x FE with L2 1000BASE-SX/LX/ZX,
EMS4 switching processing 100Base-FX (From RJ-45, LC
with interface board interface board)

Ethernet Unit
EGS4 EGS2 EGT2 EMS4
CLASS 1 STAT STAT
STAT
STAT
LASER ACT
PROG
ACT ACT
PROG
ACT
PROG
PROG
PRODUCT SRV
SRV SRV
LINK1
SRV
LINK1
ACT1 ACT1
LINK2 LINK2
ACT2 ACT2
CLASS 1 CLASS 1
SFP
SFP Module
Module
LASER
PRODUCT
CLASS 1
LASER
CLASS 1
LASER
LASER
PRODUCT
PRODUCT PRODUCT
O U T 1 IN 1
O U T 1IN 1
O U T 1IN 1
O U T 1IN 1
Indicator Color Status Description
O U T 2 IN 2
O U T 2 IN 2
On Link is established
O U T 2IN 2
O U T 2IN 2
LINK1
O U T 3 IN 3
O U T 3IN 3
Link is not
Off
established
O U T 4 IN 4
O U T 4IN 4
Flashing Data exchanged LINK ACT
LINK ACT
ACT1
No data being
Off EGS4
exchanged EGS2 EGT2 EMS4

Ethernet Unit
Board Full name Slots available Interface type Connector type
4 x FE with L2 switching
10Base-T/
EFS4 processing with interface 5 ~ 8, 11 ~ 13 RJ-45
board 100Base-TX
8 x FE with L2 switching
EFS0 6, 7, 12, 13 - -
processing board
8 (16) x FE transparent 7, 12, 13 10Base-T/
EFT8 transmission processing RJ-45
(5 ~ 8, 11 ~ 13) 100Base-TX
4 x FE transparent
10Base-T/
EFT4 transmission processing 5 ~ 7, 19 ~ 21 RJ-45
100Base-TX
8 x FE twisted pair signal 10Base-T/
ETF8 RJ-45
access board 100Base-TX
8 x FE twisted pair signal 10Base-T/
ETS8 1, 3, 15, 17 RJ-45
access switching board 100Base-TX
8 x FE optical signal
EFF8 100Mbit/s-FX LC
access board

Ethernet Unit
E F S4 EFS0 EFT 8 ET F8 ETS8 EF F8
STAT
1
STAT 2
ACT STAT
ACT ACT 3
PROG PROG PROG 4
SRV SRV SRV 5
6
7
8
LINK ACT
O U T 1IN 1O U T 2IN 2 O U T 3IN 3O U T 4IN 4 O U T 5IN 5O U T 6IN 6 O U T 7IN 7O U T 8IN 8

FE1
FE1
FE2
FE2
FE1
FE3
FE3
FE1
FE4
FE4
FE2
FE2 EFT4
FE3
FE5 STAT
FE5
ACT
PROG
SRV
FE4
FE6
FE6
FE3 FE7
LC
LC connector
FE7
FE5 connector
FE 1
FE8
FE8
FE6
RJ
RJ 45
45 connector
connector
FE2
CLASS 1
LASER
FE4 PRODUCT
FE7
FE3
FE8
FE4
CLASS 1
EFS4 EF S0 EFT8 ET F8 ETS8 EFF8 LASER
PRODUCT

Ethernet Unit
Slots Connector
Board Full name Interface type EGR2 EMR0
available type STAT

ACT
PROG
STAT
ACT
SRV PROG
2 x GE RPR
LINK1 SRV
ACT1 LINK
1000Mbit/s- LINK2
ACT2 ACT
EGR2 processing with 6, 7, 12, 13 LC

SX/LX CLASS 1
CLASS 1
interface board LASER
PRODUCT
LASER
PRODUCT
1 GE + 4 (12) x FE
10/100Mbit/s-TX,
O U T 1IN 1
RPR processing
O U T 1IN 1
EMR0 5 ~ 8, 11 ~ 13 1000Mbit/s- RJ-45, LC
with interface
SX/LX
board
O U T 2IN 2
 Function FE1
 EVPL/EVPLAN Service
FE2
 QoS
 Resilient Packet Ring Function FE3
− Weighted fair algorithm and three se GE

GE PORT
PORT FE4
rvice levels SFP

SFP Module
Module
− Auto discovery of topology
FE
FE PORT
PORT EGR2 EMR0
− Wrap and steering protection RJ

RJ 45
45 connector
connector

Ethernet Unit
Function of EFS4
C
SC
d to
Sen
Collect Alarm and
performance

FE GFP
8
X
4 VC4
VC12, VC3,
X
VC-12-Xv(x≤63),
FE
VC-3-Xv(x≤12)

Ethernet Unit
Features of EFS4
 Supports bandwidth auto-sensing

 Supports MPLS
 Supports LCAS
 Supports Port based flow control
 Supports receiving and transmitting Ethernet testing frame
 Supports inloop at Ethernet port and inloop and outloop at VC3 level
 Supports port level Ethernet performance monitoring
 Supports EPL/EPLAN/EVPL/EVPLAN services and QoS

Ethernet Unit
Common alarms of Ethernet unit
Alarm level Color Alarm name Alarm reason
Critical HARD_BAD Faulty board hardware
ETH_LOS Interrupted Ethernet link
Major TU_AIS_VC3 Interrupted contiguous VC3-xc
PROTOCOL_MM Mismatched encapsulation protocol
LP_RDI_VC3 TU_AIS_VC3 happens in the opposite node
Minor LCAS_BAND_
VC-Trunk bandwidth decreases
DECREASED

Ethernet Unit
Common performance events of Ethernet unit
DropOv Number of packet losses is over upper alarm
threshold
DropUd Number of packet losses is under lower alarm
threshold
RxBadOctOv Number of the bytes of bad packets received is
over upper alarm threshold
RxBadOctUd Number of the bytes of bad packets received is
under lower alarm threshold
TxBadOctOv Number of the bytes of bad packets transmitted is
over upper alarm threshold
TxBadOctUd Number of the bytes of bad packets transmitted is
under lower alarm threshold
ColOv Number of detected conflicts is over upper alarm
threshold
ColUd Number of detected conflicts is under lower alarm
threshold

2.1 SDH unit
2.2 Ethernet unit
2.3 Ethernet unit
2.4 Core unit
2.5 Auxiliary unit

Core Unit
 Function
 Cross-connect Unit  SCC Unit
 Timing Unit  Line unit
High-order Low-order Line unit

Board Slot
cross-connect cross-connect Connector (Interface) type
name available
capacity capacity
STM-16 SFP
I-16, S-16.1, L-16.1, L-16.2
STM-4 SFP
CXLLN 9, 10 60G 20G
S-4.1, L-4.1, L-4.2, Ve-4.2
STM-1 SFP
S-1.1, L-1.1, L-1.2, Ve-1.2

Cross-Connect Unit
SDH unit PDH unit Ethernet unit C

to SC
d
Sen
Collect Alarm and
performance
High-order cross-connect
matrix (60G)
Low-order cross-connect Multi-Granularity:

matrix (20G) VC12/VC3/VC4/VC-4-xc
Flexible service cross-connect,

loopback, multicast and broadcast

Cross-Connect Unit
2.5G line unit 2.5G line unit
2.5G line unit Cross- 2.5G line unit

connect
Cross-
connect
Standby
PDH unit PDH unit
Active
Ethernet unit Ethernet unit

Cross-Connect Unit
CXL16 C XL 4 CXL1
STAT STAT
ACTX
STAT
ACTX ACTX
Indicator Color Description

ACTC ACTC
PROG ACTC
PROG
SRVX SRVX PROG
SRVL SRVL SRVX
SYNC SYNC SRVL
ALMC ALMC SYNC
ALMC
Board works normally

CLASS 1
CLASS 1
LASER CLASS 1
LASER
PRODUCT LASER
PRODUCT
PRODUCT
STAT Board hardware fails

O UTIN
OU T IN
OUT IN
Board is powered off

RESET RESET RESET Cross-connect unit is in
ALM CUT ALM CUT ALM CUT
ACTX active status
Cross-connect unit is in
standby status
Logical unit
 GXCL (5G)
CXL16 CXL4 CX L 1  EXCL (20G)

Timing Unit
 Function
 Process 2 x 2048 kHz or 2048 kbit/s external timing signals
 Supply 2 x 2048 kHz or 2048 kbit/s timing signals
 Process SSM protocol
 Non-synchronization status message (SSM) mode
 Standard SSM mode for clock signal quality
 Extended SSM mode for clock ID
Clock works in Normal mode

SYNC
Clock works in hold-over or free-run mode

Cross-Connection and Timing Unit
Common alarms of Cross-Connect and Timing unit
Chip of the cross-connect board is damaged
Critical BUS_ERR
Damaged backplane bus
APS_INDI MSP switching happens
TEMP_OVER Ambient temperature is too high.
Major
Ejector lever on the front panel is rotated to the
W_OFFLINE
open position.
Physical interface signal of the external clock
EXT_SYNC_LOS
source is lost.
Minor
CLOCK_ENTER_N Clock working mode changes from locked into
O_TRACE_MODE holdover or free-run.
Multiplex section protection switching fails.
APS_FAIL
MS node information is lost or set incorrectly
Warning
SWITCH_DISABLE Board switching is disabled
OTH_BD_STATUS Another board pulled out or plugged in

System Control & Communication Unit
SDH unit
Commands
PDH unit
Collect Alarm and
performance NMS
Other unit
Cross-connect unit DCC
Other NE

CXL1
 Active SCC unit ACTC ( )

STAT
ACTX
ACTC
PROG
SRVX
SRVL
SYNC
ALMC
CLASS 1
LASER
PRODUCT
 Standby SCC unit ACTC ( )
 To warm reset board, press RESET

O UTIN
Reset
 To cut buzzer temporarily, press ALMC for 1 second ( )
Reset board
board
RESET
ALM CUT  To cut buzzer permanently, press ALMC for 3 seconds ( )
 To re-enable buzzer, press ALMC for 1 second ( )

Alarm
Alarm cut
cut
switch
switch
(short
(short and
and
long
long press)
press)
Logical unit
 SCC
CX L 1  GSCC (with ASON)

Functions of SCC unit
 Service configuration, grooming and monitoring

 Collect alarm and performance events
 Support NE ID setting by software
 1+1 hot backup
 Extended ECC
 Controls cabinet indicators and fans
 3 Housekeeping alarm inputs and 1 alarm outputs

NMS
Ring A Ring B
Ethernet L< 50m Ethernet

port port
Extended ECC function

Four databases on the SCC
Issued data MDB
Automatically saves the current
data in dynamic RAM.
If power fails, the data in MDB
will be lost.
MDB
DRDB
Automatically saves the Fail NE in installing
verify status
successfully verified data.
If power fails, the data in
Success
DRDB will be lost.
Boards in
FDB0, FDB1
DRDB running status
Manually or periodically
saves the data. Enduringly Save manually or
saves data and does not periodically every 30 mins
need battery.
FDB0
FDB1

Common alarms of SCC unit
Critical NESTATE_INSTALL NE is in the installing state.
Software in the master and slave SCC are
MSSW_DIFFERENT
mismatched
Inserted board and the configured board are
WRG_BD_TYPE
mismatched
Major NESF_LOST Host software is lost.
Faulty power resource, e.g. the 3.3V power
POWER_ABNORMAL module of the SCC or AUX, and the 3.3V backup
power module, and 2 channels of – 48V
POWER_FAIL Too low battery voltage on the SCC

Line Unit
CXL16
STAT
ACTX
C XL 4
STAT
ACTX
C XL 1
STAT
ACTX
 STM-1
S-1.1, L-1.1, L-1.2, Ve-1.2
ACTC ACTC
PROG ACTC
PROG
SRVX SRVX PROG
SRVL SRVL SRVX
SYNC SYNC SRVL
ALMC ALMC SYNC
ALMC
CLASS 1
CLASS 1
LASER CLASS 1
LASER
LASER
 STM-4
PRODUCT PRODUCT
PRODUCT
S-4.1, L-4.1, L-4.2 and Ve-4.2

OUTIN
OU T IN
OUT IN
 STM-16
RESET RESET RESET
I-16, S-16.1, L-16.1 and L-16.2
ALM CUT ALM CUT ALM CUT
 Automatic laser shutdown (ALS) function
 Swappable optical module (SFP)
 Support VC-4-4c, VC-4-8C and AU-4-16c services
CXL16 CXL4 CXL1

 Inloop and outloop function

2.1 SDH unit
2.2 PDH unit
2.3 Ethernet unit
2.4 Core unit
2.5 Auxiliary unit

Auxiliary Unit
Board Board name
System Auxiliary Process SAP

System Extended Interface SEI
Power Interface Board PIU
Booster Amplifier Board BA2
Pre-amplifier Board BPA
Fan unit FAN
Uninterruptible Power Modules UPM

System Auxiliary Process unit － SAP
Q1SAP
 Function STAT
PROG
PWRA
PWRB
PWRC
 Inserted in slot 14
 Provides NM interface
 Process environmental alarms
 Provides drive current for cabinet indicators
 Process orderwire bytes
 Monitor -48V power supply for Overvoltage and un
dervoltage COM
COM test port

 Provide and monitor +3.3 V power centralized bac
kup function for each board (secondary power 1:N pr ETH
otection) NM port
Q1SAP

System Extended Interface unit － SEI
ALMO1/2: Alarm output
ALMI1/2: 8 x Environment alarm input
LAMP1/2: Cabinet indicator output
OAM: X.25 OAM
F1: Co-directional data 64 Kbit/s
S1 ~ S4: Serial 1 ~ 4 broadcast data
F&f: LCT
PHONE: Orderwire
CLK1/2: 120 Ω Ext clock input/output 1/2
V1/2: NNI Audio/Signaling
LAMP LAMP OA F&

ALMO1 ALMO2 F1 PHONE CLK1 CLK2
1 2 M f
CLKO1 CLKO2 CLKI1 CLKI2
ALMI1 ALMI2 S1 S2 S3 S4 V1 V2
CLKO1/2: 75 Ω Ext clock output 1/2 CLKI1/2: 75 ΩExt clock input 1/2

Power Interface Board － PIU
 Function
 Access power
 Lightning protection
 Enhance the electro magnetic compatibility (EMC)
of the system by filtering and shielding the power
supply.
 Protect the power interface from damage caused
by misconnection.
 1+1 hot backup protection

Power Interface Board － PIU
Interface Description
PWS 50 W power output interface,
supplying power for COA or HUB
PIU
PWS
PWR –48 V power access interface
RTN(+)
PWR
NEG(-)

FAN Unit
FAN Unit

FAN Unit
 Function
 Support hot swapping
 Automatic speed adjust
ment

STAT The fan operates normally.
The fan, fan power board or FANA is abnormal.
The fan is turned off due to low temperature.

The faulty fan
Major FAN_FAIL
The fan is power off

Questions
 How many types of boards are there in OptiX OSN 2500?

Summary
Unit Constituent board Function
Processing with SL16, SLQ4, SLD4, R1SLD4,
optical interface SL4, R1SL4, SLT1, SLQ1, Access and process STM-N
board R1SLQ1, SL1, R1SL1, SEP1 signals and concatenated optical
SDH
unit Interface board EU08, OU08, EU04 signals.
Protection switching Implement TPS protection.
TSB8
board
Processing with
SPQ4, PD3, PL3, PQ1, PQM, Access and process E1, E1/T1,
electrical interface
PDH PD1 E3/T3, E4/STM-1 electrical
board board
unit signals.
MU04, D34S, C34S, D75S,
Interface board Implement TPS protection.
D12S, D12B
Processing with
optical/electrical EGS2, EGT2, EMS4, EFS0, Access and process FE, GE
Ethernet Interface/ Processing EFS4, EFT8, EFT4 signals.
unit board Implement TPS protection
Interface board ETF8, EFF8, ETS8

Summary
Unit Constituent board Function
Ethernet Processing with
EMR0, EGR2 Access and process FE, GE signals. Support
interfac Interface board
RPR and conduct TPS protection for Ethernet
e unit
Interface board ETF8, EFF8, ETS8 signals. Implement TPS protection.
(RPR)
ADL4, ADQ1, IDQ1, Access and process STM-4, STM-1 ATM
ATM interface unit
IDL4 signal.
MR2A, MR2B, Provide add/drop multiplexing of any two
MR2C adjacent wavelengths.
WDM unit Implement conversion between client signaling
wavelengths of any rate (10 Mbit/s to 2.7
LWX
Gbit/s NRZ code signal) and those
wavelengths complying with G.692 standard.
Implement cross connection and provide the
equipment with system clock.
CXL1, CXL4, Provide interface for connecting the equipment
Core unit
CXL16 with the NM system and process the overhead
of SDH signals. Support intelligent feature.
Provides the optical interface.

Summary
Constituent
Unit Function
board
Power input unit Provide power supply and protect the
PIU
equipment against abnormal power
Inter-board communication Implement centralized power backup
and power backup unit SEI function and provide auxiliary interfaces
externally (F1, alarm and external clock)
Fan unit FAN Dissipate heat for the system
Optical booster
Other BA2, BPA Amplify or pre-amplify the optical power
amplifier board
functional
units Case-based 61COA and Amplify the optical power and installed in
optical amplifier 62COA the cabinet

Chapter 3 Features

Equipment Protection
S S S S S S S S S S S S S S S S S S
L L L L L L L L L L L L L L L L L L
O O O O O O O O O O O O O O O O O O
T T T T T T T T T T T T T T T T T T
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
C C S
X X A
L L P
P W W W W
S S S S S S S S S S S S S S S S S S
1:4 TPS of E1/T1 board L L L L L L
O O O O O O
L
O
L
O
L
O O
L
O
L L
O
L
O
L
O
L
O
L
O
L
O
L
O
T T T T T T T T T T T T T T T T T T
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
T C C S T
S X X A S
B L L P B
P W W P
2 groups 1:1 TPS for E3/T3/E4/STM-1(e)/FE board

Items protected Protection scheme
E1/T1 processing card 1:N (N 4) TPS

E3/T3 processing card 1:1 TPS (2 Groups)
E4/STM-1 processing card 1:1 TPS (2 Groups)
FE processing board 1:1 TPS (2 Groups)
Core unit 1+1 hot backup protection
-48V power interface card 1+1 hot backup protection
3.3V card power supply 1:N centralized hot backup protection
* The OptiX OSN 2500 can support two TPS groups of different types of services at the one time.

 Fans
 The mutual backup of power supplies for the fans
 Automatic fan speed adjustment
− Once one fan modules goes faulty, the other two will operate at the
ir full speed.
− Turns off the fans at low temperature
 Abnormality-Specific Board Protection
 Check function of application program and data
 Over-voltage and under-voltage protection
 Board temperature check

Network Level Protections
Protections Types
1+1 MSP
Linear MSP
1:N (1 ≤ N ≤ 14) MSP
2-fiber bidirectional MSP ring
MSP ring 2-fiber unidirectional MSP ring
4-fiber bidirectional MSP ring
Mesh Protection Intelligent function
SNCP
Dual node interconnection (DNI)
Fiber-Shared Virtual Path Protection
MS-Shared Optical Path Protection
RPR
VP-Ring/VC-Ring Protection

Intelligent Features
 Service level agreement (SLA)
 Topology automatic discovery function
 Automatic end-to-end service configuration
 Support mesh networking and protection
 Traffic engineering
Resilient Packet Ring (RPR)
 Topology automatic discovery function

 Fair algorithm
 3 service levels

Summary  Product Introduction
 Cabinet, Sub-rack and Boards
 Features

Thank You
www.huawei.com

OTA105102 OptiX OSN 2500 Hardware Description ISSUE 1.20

Uploaded by

Copyright:

Available Formats

OTA105102 OptiX OSN 2500 Hardware Description ISSUE 1.20

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

OTA105102 OptiX OSN 2500 Hardware Description ISSUE 1.20

Uploaded by

Copyright:

Available Formats

Internal

OTA105102 OptiX OSN 2500

ISSUE 1.20 www.huawei.com

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 2

Chapter 2 Cabinet, Sub-rack and Boards

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 3

What is OSN 2500 ?

 Full name: OptiX OSN 2500 intelligent optical switching system

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 4

OSN 1500/Metro OSN 2500 /Metro OSN 1500/Metro Access

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 5

STM-4 Cross-connect Unit

External Timing Auxiliary Management

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 6

Cross-connect matrix higher-order

E1/T1/E3/T3/E4 FE/GE ATM

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 7

Chapter 2 Cabinet, Sub-rack and Boards

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 8

ETSI 300/600 Cabinet Weight Max. number of

600 (W) x 300 (D) x 2000 (H) 55 2

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 9

On Cabinet is powered ON Power distribution unit

Power Consumption and Fuse 400 15

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 10

RTN1(+) RTN2(+) NEG1(-) NEG2(-)

1. Power socket (left) 2. Power cable RTN1(+) 3. Power cable RTN2(+)

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 11

Chapter 2 Cabinet, Sub-rack and Boards

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 12

Service slot area

Interface slot area

Dimensions (mm) 447 (W) x 295 (D) x 472 (H)

Weight (kg) 17 (not including boards and fans)

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 13

Fiber routing panel

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 14

Fiber routing panel

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 15

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 16

 Board Appearance and type

 Processing with Interface

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 17

7, 8, 11 ~ 13 Fixed wavelength output, I-16, S-

 Signal processing with optical interface board

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 18

Indicator Status Color Description OUT

On, green Board works normally.

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 19

Indicator Status Color Description

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 20

SL16 SL16A SLQ4 SLD4 S L4

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 21

Send to Cross-connect unit

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 22

 Fixed wavelength output

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 23

Receiver overload (dBm) -3 0 -9 -9 -9 -9 -10

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 24