Earth Work Guide Lines As Per GE 0014 in Indian Railways
Earth Work Guide Lines As Per GE 0014 in Indian Railways
Earth Work Guide Lines As Per GE 0014 in Indian Railways
for
Design of Formation
for
Heavy Axle Load
2
# Number Name
1 GE: G-1 (2003) GUIDELINES FOR EARTHWORK IN RAILWAY PROJECTS
4
GE 0014….Highlights
5
GE 0014… Highlights
• CBR based value for subgrade soil selection
incorporated on the pattern of Highways design,
(IRC:37 “Design of Flexible Pavements’).
• Concept of Elastic modulus of compacted layer (EV2)
determined from second loading in Plate Load Test has
been introduced as a quality assurance test similar in
UIC railways.
• The Guidelines also includes special features like
– Ground improvement methods
– Quality assurance tests
– Important considerations (to be kept in view for construction of
good quality formation suitable for running of heavy axle loads).
• The present documents has been finalised based on
the approved recommendations by the Railway Board
letter no. 2007/CE-I/Geotech/02 dated 26.10.2009.
6
DEFINITIONS
• Formation: Layers comprising blanket, sub-grade / top
layer of formation, and embankment fill.
• Formation Top: Boundary( interface) between ballast
and top of blanket.
• Track Foundation: Constitutes ballast, sub-ballast,
blanket and subgrade.
• Cess: Portion at top from toe of ballast to edge of
formation.
• Ballast: Crushed stones below the sleepers.
• Sub-ballast: A layer of coarse-grained material provided
between blanket/subgrade and ballast and confined to
width of ballast section only. (However, sub-ballast is not in vogue on Indian
Railways. Therefore, its provision has not been considered in these Guidelines.) 7
DEFINITIONS
• Blanket: Layer of specified coarse, granular material of
designed thickness provided over full width of
formation between subgrade and ballast.
• Prepared Subgrade : The upper part of the subgrade
(which normally has a crossfall.)
• Sub-grade: Upper part of embankment/cutting
provided above subsoil
• Cohesive Subgrade: Subgrade constructed with soils
having cohesive behaviour (i.e., shear strength is
predominantly derived from cohesion (Normally, soils having
particles finer than 75 micron exceeding 12% exhibit cohesive behaviour. As per IS classification,
all fine-grained soils and GM, GM-GC, GC, SM, SM-SC & SC types of soils exhibit cohesive
behaviour.
•
8
DEFINITIONS
• Cohesion-less Subgrade: Subgrade constructed with
cohesion-less, coarsegrained soils i.e., shear strength is
predominantly derived from internal friction of the soil
are termed as cohesion-less subgrade. Normally, soils
having particles finer than 75 micron less than 5%
exhibit cohesion-less behaviour. As per IS Classification,
GW, GP, SW & SP types of soils fall in this category.
• Dispersive Soil: Dispersive clayey soils are those, which
normally deflocculate
• Sub-soil: Soil of natural ground
• Unstable Formation: Yielding formation with continued
settlement and/or slope failure.
9
DEFINITIONS
• Shear Strength: Ability to resist shearing at a shearing
surface (plane) under direct stress ( vertical pressure)
• Soil Pressure Units: equivalence:
– 1 Pascal (Pa) = 1 ( N/m2)
– 100 kPa = 10 t/m2 = 1 Kg/cm2 = 1/10 N/mm2 = 1/10 MPa
10
FORMATION COMPONENTS
• Formation comprises of Granular layer (sub-
ballast and or Blanket) over prepared
subgrade and embankment fill.
11
Objectives of Soil Exploration
• To determine soil type with a view to identify their
suitability for earthwork in formation and to design
the foundation for other structures.
• To avoid known troublesome spots (unstable hill sides,
swampy areas, soft rock areas, peat lands, etc.)
• To determine method of handling and compaction of
subgrade.
• To identify suitable alignment for embankment and
cutting from stability, safety, economy in construction
and maintenance considerations.
• To identify suitable borrow area for desired quality
and quantity of subgrade and blanket material.
12
Objectives of Soil Exploration
• To determine depth of various strata of soil and bed
rock level.
• To determine ground water table position and its
seasonal variation and general hydrology of the area
such as flood plains, river streams, etc.
• To determine behavior of existing track or road
structure nature and causes of geo-technical
problems in them, if any.
13
Soil Investigation during Reconnaissance Survey
• objective ~ to collect maximum surface and sub-
surface information without drilling exploratory
boring/ test pits
• available data from geological and topological maps
and other soil surveys done in past, existing soil
profiles in nearby cuts, quarries are scrutinized.
Water table is recorded from local observation and
inquiry.
• Survey reports available from other Departments
• data and information collected should be presented
in suitable format such as graphs, bar chart or in
tabular or statement form
14
Soil Investigation during Preliminary Survey
• Objective ~ to obtain sufficient subsurface data.
• compass traverse along one or more routes with
transverse and longitudinal levels to prepare an L-
section of routes proposed
• shall also cover a soil survey by sampling at suitable
intervals.
• Exploratory boring / Soil sampling @ 500 meter or
closer . The boring should be done upto 1.5 to 2.0 m
depth below existing ground level.
• High embankment / problematic Substrata ~ boring
equal to twice the height of embankment.
15
Soil Investigation during Final Location Survey
• detailed investigations done at locations
where important structures (viz. high bank, deep cuttings, major
bridges etc. are to be located and where weak sub-soil, swampy ground, marshy land exist)
16
ASPECTS OF DESIGNING SUBSOIL, EMBANKMENT AND TRACK
SUBGRADE
• Formation has to be provided with layers well
designed to be safe against shear failure, and
accumulated/ plastic deformations under
repetitive axle loads.
• The Blanket layer and the subgrade layer
provide support to the track structure and bear
additional stresses due to static and dynamic
effects of moving wheel loads. Load is
transmitted through the sub-grade and
embankment fill layers to subsoil/ ground level.
17
Subsoil Deformation
• Reasons
– subsoil deformation due to embankment fill loads
and relief,
– settlement of the embankment fill due to
deadweight, and
– deformation ( plastic) due to dynamic influence of
traffic loads
18
Settlement Behaviour of the Subsoil
• Influenced by strength and stage of
consolidation of the underlying layers. The
three phases of deformation/ settlement are:
– Immediate settlement ( gravel and sand) (non-
cohesive soils)
– Primary settlement (consolidation) (soft cohesive
soils without previous loading and may prolong to
few years)
– Secondary settlement ( creep) (soils with high clay
content and high content of organic material.)
19
Pressure on Formation and sub-soil
• At bottom of ballast: <= 0.3MN/m2 or 3
kg/cm2
• On sub-soil <= 0.1MN/m2 or 1 kg/cm2
20
21
Geometrical requirements for the soil formation
• cross fall slope to be at least 1:30 or 3% with tolerance of 0.5%.
• The finished top levels should be within + - 3cm
• Finished soil surface to be in level in longitudinal direction( <= 2cm
on a longitudinal base of 4m), must not show hollow pits, road
vehicle traffic ruts.
• Side slopes to extend in horizontal plane, minimum 10 cm beyond
the theoretical finished lines, and later cut and dressed to the
specified dimensions.
• Recommended formation top width for Heavy Axle Load Track is
8.5 m for single line and 8.5 m plus distance between track centers
for double line section, and for DFC shall be minimum 13.5 m (as
per GE 14). However CC tr distance as per SOD for DFC is 6.0 m.
Which gives 14.5 m.
• Additional Width of formation: For extra ballast on outside of
curves and extra clearance required on double line for super-
elevation etc
22
Drainage of Formation
• The aim is to contain/ reduce water content in the
formation layers by following measures:
– Removal of vegetation growth on surface
– Cleaning of ballast bed and establishing cross fall slope at top of
formation/ blanker and sub-grade layers.
– Provision of longitudinal drains and drainage outfall, facilities
– Arrangement of lateral side drainage facilities.
23
Sub-soil Drain System
• To be installed where the ground water level
has to be lowered (depth < 1.5 m below the
rail top)
24
25
26
Other Design Aspects
• suitable and cost-effective erosion control system
considering soil matrix, topography and hydrological
conditions.
• keep borrow pits sufficiently away from the toe of the
embankments to prevent base failures due to lateral
escapement of the soil.
• distance of borrow pit to be decided in each case on its
merits.
• For embankments / cuttings in highly cohesive clayey soils,
special treatment may be necessary to ensure a stable
formation.
• minimum height of embankment should not be less than
one meter to ensure proper drainage, effective stress
dispersal, and uniform riding qualities.
• Soils prone to liquefaction and having coefficient of
uniformity, Cu < 2 should not preferably be used in
Earthquake prone areas. 27
Ideal Soil and Poor Soils
• Ideal soil:
– High bearing capacity(BC) in reference to static loads, minor settlement
– High BC in reference to dynamic loads, due to unequal grain size, high
structural resistance, and good consolidation
– Elasticity
– Stable as regards erosion
– High water permeability
– Filter criteria w.r.t ballast layer above and sub-soil below
– Cost effectiveness in supply and construction
Natural soils are rarely ideal soils.
• Poor Soils:
– Non-cohesive and loose
– Cohesive, soft to semi-solid mixed soils with various contents of sand,
silt, clay and water
– Or contain solid rocks of irregular size, solid rocks with cohesive
weathering elements.
28
Subgrade Modulus
• measure of stiffness (of bedding layers), parameter linked
to bearing capacity of soil as well and takes in account
deformation condition.
• determined in plate load bearing tests
– E1 … modulus of elasticity at first loading
– E2 … modulus of elasticity at second loading
– Ev … modulus of deformation
– Ev2 … modulus of elasticity (also deformation) at the second step
loading during the plate load test
– Edyn … modulus under dynamic load; approx. 1.2 to 2.5 times the
– E2 modulus; for cohesive soil is of the order 45 N/mm2, for non-cohesive – 60
N/mm2.
– Er … Resilient Modulus of soil layer(subgrade/formation/subsoil layers)
29
Permissible Contact Pressure and Modulus of Elasticity
• Permissible compressive stress on the formation can
be typically estimated using the empirical formula
according to Heukelom and Klomp
• Where
– σzperm is permissible compressive stress on the formation
– Ev2 : Modulus of Elasticity
– n= number of load cycles.
30
Coefficient of Ballast
• The track substructure response in terms of surface
pressure between sleeper and ballast, and the
vertical settlement under load.
• Quantitatively, C= 1 N/cm3, is the value of N/cm2
surface pressure when the sleeper subsides by 1 cm
31
Typical Values Of Soil Types
32
FUNCTIONS OF BLANKET LAYER
• Primary Function
– Stress Reduction Function - It reduces the traffic induced
stresses on top of sub-grade to a tolerable limit.
• Secondary Function
– Separation Function: prevents penetration of ballast into
sub-grade also prevents upward migration of fine particles
– Drainage Function: Should intercept water coming from
ballast away from sub-grade and at the same time, permit
drainage of water that is flowing upward from the sub-
grade.
– Prevention of Mud Pumping: It prevents mud pumping by
checking attrition of sub-grade particles by ballast
33
11.0 DESIGN OF FORMATION FOR 25, 30 & 32.5 T AXLE LOAD
UIC Method (Based on fines in Soil)
• Recommendations in UIC Code 719
• Calculated Thickness of blanket material & prepared
sub-grade and type of subgrade alongwith soil types
as per IS Classification belonging to various ‘Soil
Category SQ’ have been given in Table-2
• Soil Categories SQ1, SQ1 & SQ3 have been modified
slightly from UIC practices to suit Indian conditions &
BIS Classification system.
34
Table 3 - Description of Soil Quality Class
35
Table 2 - UIC Based Two Layers System of Blanketing On Track
Formation
36
11.2 AAR Design (Selig Method) – Based on
Cumulative Strain & Plastic Deformation Criteria
• calculations have been done for 25, 30 & 32.5 T for different
values of Compressive Strength, σs of soils.
• Table 4 - Calculation of Blanket Thickness (in cm) For
different Axle loads & CBR of soil
37
Assumptions in AAR design
• Soil Compressive Strength, (in kPa) , σs = 30 x CBR
• Elastic Modulus of ballast, Eb has been assumed to be 140
MPa.
• Elastic Modulus of Soil, Es =10 x CBR (For CBR <= 5) & Es =
17.6xCBR 0.64 (For CBR> 5)
• Values of a, b & m for soil & Curves for Soil have used for CH
type soil..
• Depth of deformable subgrade, T has been assumed as 2.0 m.
• GMT is 30 and design period is 5 year. ( i.e. Total Design GMT
is 150)
• Permissible cumulative plastic strain, εpa at the end of design
period is 2%.
• Permissible cumulative plastic deformation at the end of
design period is 25mm.
• Ballast Thickness is 30 cm.
38
12. RECOMMENDED SPECIFICATIONS OF BLANKET MATERIAL
(Mandatory)
• Cu > 7 and Cc between 1 and 3.
• Fines (passing 75 microns) : 3% to 10%.
• Los Angeles Abrasion value < 35%. (relaxable to 40% by
PCE/CAO on techno economic criteria)
• Minimum required Soaked CBR value 25 of the
blanket material compacted at 100% of MDD.
• Filter Criteria (at present Optional) should be
satisfied with prepared subgrade/subgrade layer just
below blanket layer, as given below :
– Criteria–1: D15 (blanket) < 5 x D85 (sub-grade)
– Criteria–2: D15(blanket) > 4 to5 D15 (sub-grade)
– Criteria–3: D50(blanket) < 25 x D50 (sub-grade)
39
• Criteria 1 causes particles at the coarsest end of
the protected soil (D85) to be blocked by
particles at the finest end of the filter (D15).
• Criteria 2 is an additional criteria to ensure
adequate permeability to drain sub-grade.
• Criteria 3 is only a suggestive provision which
helps to avoid gap-graded filters and create a
filter gradation that is somewhat parallel to that
of protected soil.
• I t may be relaxed in except ional cases by CTE on
Open Line & by CAO/ C in const ruct ion projects
on technical and economic considerations.
40
GE
14
GE
1
41
13.0 QUALIFYING AND QUALITY ASSURANCE TESTS
(Mandatory)
• Selection of soil: CBR test is conducted on ground soil,
embankment fill, prepared sub-grade & blanket material to ensure the
minimum specified CBR value of these materials to be used in
construction
• Quality Assurance Test on Compacted Layer: Required
to be conducted on part completion stages of formation, prior to clearing
for further earthwork, track linking work.
• Heavy Proctor test as envisaged in GE:G-1
• Second Step Plate Load Test (Optional) is required to be
conducted in-situ for measurement of Deformation Modulus
EV2 of compacted layers of embankment, blanket, prepared
subgrade.
42
Frequency of Quality Assurance Tests
• CBR test for selection of formation materials and other
tests e.g. size gradation, Cu, Cc, Los Angles Tests,
OMC/MDD etc. shall be conducted at following
frequency :
– Embankment Fill : one set of tests for every 5000 cum
– Prepared subgrade : one set of tests for every 2000 cum
– Blanket material : one set of tests for every 500 cum
• In-situ Degree of Compaction (or In-situ dry density
measurement) test shall be conducted on each
compacted layers in random pattern
– Embankment Fill : one density measurement at every 500 sqm surface
area of each compacted layers
– Blanket and Prepared Subgrade : one density measurement at every 200
sqm surface area of each compacted layers.
• Second step Plate Load Test: At the frequency of one test per km
length of section.
43
15.0 DISCUSSIONS ON FORMATION LAYERS SYSTEM
• From the stress analysis, it is evident that most of
stresses for heavy axle load up to 32.5 T load are
dissipated upto 1.5 m depth below bottom of ballast.
• The major stress region occurs upto depth of 1 to
1.5m below bottom of ballast.
• This region is to be provided with blanket layer which
or in lower layers supplemented / replaced by
prepared subgrade particularly in bottom portion.
• Minimum CBR value of subgrade/prepared subgrade
have been prescribed for selection of soil/material
for the subgrade
44
17. SPECIFICATIONS & RECOMMENDATIONS :
(Mandatory)
• Following Specifications for two different systems
for blanket, subgrade, embankment fill are
mandatory provisions to be adopted, as follows:
– Conventional blanket layer over formation subgrade
– Blanket layer over prepared subgrade layer
(good/imported soil)
Any of the two system may be considered for
adoption in the field based on good soil
availability and material cost economics
45
17. SPECIFICATIONS & RECOMMENDATIONS :
(Mandatory)
• Any of the two system may be considered for
adoption in the field based on good soil
availability and material cost economics
• These are given in form of following:
– Table 6 (Specification and thickness of subgrade
layers for Heavier Axle Loads),
– Formation cross-sections (Fig. 10 – Formation
Profiles and Layers for Heavy Axle Load), and
– Bar Diagrams (Fig. 11 – Formation Layer
Thickness).
46
Table 6: Single Blanket Layer over Embankment Fill- Specification and Layer
Thickness
47
Two Layer System (Blanket & Prepared Subgrade on Embankment Fill)
48
Formation Profiles and Layers for Heavy Axle Load
Single Layer System (Blanket on Embankment Fill)
49
Formation Profiles and Layers for Heavy Axle Load
Single Layer System (Blanket on Embankment Fill)
50
Formation Profiles and Layers for Heavy Axle Load
Single Layer System (Blanket on Embankment Fill)
51
Formation Profiles and Layers for Heavy Axle Load
Two Layer System (Blanket + Prepared Subgrade on
Embankment Fill)
52
Formation Profiles and Layers for Heavy Axle Load
Two Layer System (Blanket + Prepared Subgrade on
Embankment Fill)
53
Formation Profiles and Layers for Heavy Axle Load
Two Layer System (Blanket + Prepared Subgrade on
Embankment Fill)
54
Bar Diagrams Showing Formation Layers Thickness:
Single Layer System
55
Bar Diagrams Showing Formation Layers Thickness:
Two Layer System
(Blanket + Prepared Subgrade on Embankment Fill)
56
RB’s recent guidelines on Formation Design
58
59
Requirement of Blanket Layer:
• blanket layer shall not be needed when formation/
earth fill embankment have :
– Rocky beds except those, which are very susceptible
to weathering e.g. rocks consisting of shales and
other soft rocks, which become muddy after
coming into contact with water.
– Soil of GW, SW, GW-GM, SW-SM type
– Soils conforming to specifications of Blanket material.
– Coarse granular, well graded (Cu>7, Cc between 1
and 3) soil/quarry dust/crushed stones material of
300 mm thickness is laid as top layer.
60
Requirement Of Blanket Layer
• For other conditions, the system of layered
construction of embankment consisting of
prepared subgrade shall normally be followed.
The Prepared sub-grade should normally
consist of good quality soils with fines less
than 12% (A or B1).
• The level of compaction of various layers of
formation shall be ensured as defined in
guidelines issued by RDSO
61
Thickness of Prepared subgrade and Blanket Layer:
62
Thickness of Prepared subgrade and Blanket Layer:
• In case good quality soils with fines less than 12% (A or B1),
are not available for preparation of subgrade economically,
soils having fines between 12% to 50% (B2) can be used over
embankment fill of soil group C. In such cases, the thickness
of blanket layer over prepared subgrade of 500 mm
thickness shall be kept as 250mm. The thickness of blanket
layer can be reduced to 150mm by use of Geotextile in
consultation with RDSO.
• In case, the prepared subgrade is not considered on
economic considerations and use of other types of soil not
covered by above clauses is required, Railways may approach
RDSO for getting guidance on deciding blanket thickness
depth.
63
Thickness of Prepared subgrade and Blanket Layer:
• Use of Geosynthetics (Geo textile/ Geo grids)
shall be considered at places where it is
economical to use it in combination with blanket
as it reduces the requirement of thickness of
blanket. Use and selection of Geosynthetics
should be done in consultation with RDSO.
• Selection of top layers for design of formation as
well as for blanket material as given in above
Paras and further deviations from these
provisions can be finally decided on techno-
economic considerations by CAO(Con.) after
recording the reasons.
64
Specification of Blanket Material
• The material for blanket layer over prepared sub-
grade should be well graded granular material .
• The following specifications shall be ensured at the
time of laying:
– Cu > 7 and Cc between 1 and 3
– Fines (passing 75 microns): 3% to 10 %.
– Minimum required Soaked CBR value 25 of the
blanket material compacted at 100% of MDD.
65
17. SPECIFICATIONS & RECOMMENDATIONS : (Mandatory)
• In order to design & construct stable formation for
heavy axle load:
– EV2 should be determined in the field as per procedure
given in German Code DIN :18134 at ground.
– Undrained shear strength, Cu of ground soil from
Unconfined Compression (UCC) test or Vane Shear Test
and Penetration Number (N –Value) from Standard
Penetration Test should also be determined.
• If EV2 value is less than 20 MPa or Sub-soil strata
having (Cu) < 25 KPa (mostly in Marshy area) or N-
value < 5 will also require ground improvement.
66
Standard Test Procedure For California Bearing Ratio
(Laboratory Method)
• California Bearing Ratio (CBR) test is a penetration test
developed by the California State Highway Department of
USA for the evaluation of subgrade strengths for roads
and pavements.
• Ratio of Force per unit Area required to penetrate a soil
mass with a circular plunger of 50 mm diameter at the
rate of 1.25 mm/minute to that required for
corresponding penetration of a standard material.
• The test is arbitrary and results may not be directly
related to fundamental properties governing the strength
of soils such as cohesion, angle of internal friction etc.
• test may be conducted on undisturbed as well as
disturbed
67
Standard Test Procedure For California Bearing Ratio
(Laboratory Method)
• CBR=PT/Psx100
• Where,
• PT =Corrected load corresponding to the chosen penetration from the load penetration curve,
• Ps =Standard load for the same depth of penetration as for Ps
68
GROUND IMPROVEMENT
• For ground soil/ sub-strata layers with low
bearing capacities Shall require Ground
Improvement.
– Ev2 value less than 20 MPa, (Optional) or
– Undrained cohesion (Cu) < 25 kPa, or
– N-value (determined from Standard Penetration
Test –SPT ) < 5
69
GROUND IMPROVEMENT METHODS
• Strengthening of sub-strata soil layers can be carried
out using one or more of the following techniques
– removal and replacement ( R&R) of weak soil,
– stage constructions of the fill, preloading and surcharging,
– Installation sub drainage system,
– In-situ pile, Sand Gravel Compaction pile, Stone Colums
– Vibro-floatation,
– lime pile, Injection/ lime slurry pressure injection/ion
exchange,
– Stir & Mixing,
– Sand mat, Geosynthetics etc.
70
1. Removal and Replacement of weak soil
• For localised areas with soft soils (having undrained
shear strength less than 20 kPa or CBR<3) of limited
depth and thickness, removal of unsuitable material
and replacement with suitable fill may be carried out.
• Excavation and replacement could be carried out up
to 2 m.
• Even in ‘cutting’ areas where the naturally occurring
soils areof a low shear strength and high moisture
content.
– Subsurface drainage may have to be introduced in most of
such areas.
71
2. Stage constructions of the fill
• The technique can enhance the bearing capacity of the
sub-soil
• Stage construction is employed mainly as a means of
gradually increasing the shear strength of a soft clay.
• In stage construction, advantage of increase in shear
strength of sub-soil strata due to consolidation by
surcharge of embankment loading is taken into account.
• Principle of stage construction method is shown in figure
below
72
3. Preloading and surcharging
• adequate instrumentations for monitoring the
settlements, development and dissipation of
pore water pressures is essential
• economical for soft clays, since, the material
can stay in place and need not be relocated.
• Method is based on the consolidation
concepts, whereby pore water is squeezed
from the voids until the water content and the
volume of the soil are in equilibrium under the
loading stresses imposed by the surcharge
73
4. Installation of vertical drainage system
• Used where preloading alone not efficient.
• They accelerate the primary consolidation of clay
by rapid dissipation of excess pore water
pressure.
• No direct effect on the rate of secondary
compression but helps in the earlier onset of
secondary settlement.
• Therefore the structures or embankments can be
put to use earlier than it would be possible
otherwise.
• Steep side slopes and avoidance of berms in case
of embankments may be possible when sand
drains are used.
74
4. Installation of vertical drainage system
• The effectiveness of vertical drains depends
mainly on the engineering properties of soils,
namely, soil permeability and coefficient of
consolidation and their variations in space and
time.
• Vertical drains can be successful in
accelerating the rate of consolidation of soft
fine-grained soils. They are, however,
ineffective in organic soils and highly stratified
soils.
75
4. Installation of vertical drainage system
• Prefabricated vertical PVC drain can be defined as any
prefabricated material or product consisting of a
synthetic filter jacket surrounding a plastic core.
• Because of their shape, they are also known as band or
wick drain.
• The details of PVC drains and their installation
techniques are given in “Prefabricated PVC Vertical
Drainage System for Construction of Embankment on
Compressible Soft Soil” Report No. GE-R-68, December
2004.
76
5. In-Situ Pile/Sand Gravel Compaction Pile/ Stone Columns
• Granular piles are composed of compacted
sand or gravel inserted in to the soft clay
foundation by displacement method.
• The ground improved by by compacted
granular piles is termed composite ground.
• On loading, the pile bulges into the sub-soil
strata and distributes the stresses at the
upper portion of the soil profile rather than
transferring the stresses in to the deeper
layer, thus causing the soil to support it.
77
5. In-Situ Pile/Sand Gravel Compaction Pile/ Stone Columns
82
9. Stir & Mixing
• The deep mixing method (DMM) originally was
developed to improve the soft ground for port
and harbor structures.
• Now this method widely applied to the earthen
structures like dams, embankments etc.
• Three categories:
– a) Mechanically mixing method and
– b) Slurry jet mixing
– C) Dry Jet Mixing method (DJM). Cement or quicklime
powder is injected into the deep ground through a
nozzle pipe with the aid of compressed air and then
the powder is mixed mechanically by rotating wings.
83
10. Sand mat
• Dissipation of excess water from the soft soils
by the means of vertical sand drains,
horizontal sand drains and the provision of the
sand layer at the ground level to improve the
bearing capacity as well as the drainage of
excess water which is responsible for
increasing the pore water pressure within the
soil mass.
• Some times, when fill material of the
embankment is also of poor quality required
sand layers of 30cm thick at the interval of 2-
3m known as the sandwich construction.
84
Sand mat with the help of vertical sand drains/piles
85
Sand mat with the help of Horizontal sand
drains/sandwich system
86
11. Stabilization & Ground Improvement Methods
Using Geosynthetics
87
11a. Geocell
• The incorporation of a geocell foundation mattress
provides a relatively stiff foundation and maximizes
the bearing capacity of the underlying weak soil.
• The geocell mattress technique is particularly effective
with relatively thin soft foundation layers where the
ratio of embankment width to depth of soft soils is
greater than four.
• It is a honeycombed structure formed from a series of
interlocking cells. These cells are fabricated in-situ
directly on the soft foundation soil using geogrids
which are filled with granular material / locally
available infill material.
88
89
11b. Load Transfer Platform
• The use of stone columns/ piles allows transferring the
load of the embankment to the firm stratum below.
• As a process, the load from the embankment must be
effectively transferred to the columns to prevent
punching of the columns through the embankment fill
creating differential settlement at the surface.
• In order to increase the spacing of columns, to
minimize the size of pile caps required to support the
embankment and to increase the efficiency of the
design, a load transfer platform (LTP) reinforced with
geosynthetic reinforcement is used.
• A load transfer platform consists of one or more layers
of geosynthetic reinforcement placed between the top
of the columns and the bottom of the embankment.
90
Schematic Sketch of a Load Transfer Platform
91
THANKS
92