A Crisis of More Area Than The Required Heat Exchanging Surface Area

A crisis of More Area than the Required Heat
Exchanging Surface Area

Why a Shell and Tube Heat Exchanger?
• Shell and tube heat exchangers are the most widespread

and commonly used basic heat exchanger configuration in
the process industries.
• The reasons for this general acceptance are several.
• The shell and tube heat exchanger provides a
comparatively large ratio of heat transfer area to volume
and weight.
• It provides this surface in a form which is relatively easy
to construct in a wide range of sizes.
Better Concurrence….
• It is mechanically rugged enough to withstand normal shop

fabrication stresses, shipping and field erection stresses,
and normal operating conditions.
• The shell and tube exchanger can be reasonably easily
cleaned, and those components most subject to failure -
gaskets and tubes – can be easily replaced.
• Shop facilities for the successful design and construction
of shell and tube exchangers are available throughout the
world.
Simple Shell & Tube Heat Exchanger
Inner Details of S&T HX
Components of STHEs
• It is essential for the designer to have a good working

knowledge of the mechanical features of STHEs and how
they influence thermal design.
• The principal components of an STHE are:
• shell; shell cover;
• tubes; tubesheet;
• baffles; and nozzles.
• Other components include tie-rods and spacers, pass
partition plates, impingement plate, longitudinal baffle,
sealing strips, supports, and foundation.
Types of Shells
Fixed tube sheet
U-Tube STHE
Floating Head STHE TEMA S
Floating Head STHE TEMA T
A New Part…. Only for SHTE
Cross Baffles
• Baffles serve two purposes:
• Divert (direct) the flow across the bundle to obtain a higher
heat transfer coefficient.
• Support the tubes for structural rigidity, preventing tube
vibration and sagging.
• When the tube bundle employs baffles,
• the heat transfer coefficient is higher than the coefficient for
undisturbed flow around tubes without baffles.
• For a baffled heat exchanger the higher heat transfer
coefficients result from the increased turbulence.
• the velocity of fluid fluctuates because of the constricted area
between adjacent tubes across the bundle.
Types of Baffle Plates : Segmental Cut Baffles
• The single and double segmental baffles are most frequently used.
•They divert the flow most effectively across the tubes.
•The baffle spacing must be chosen with care.
•Optimal baffle spacing is somewhere between 40% - 60% of the
shell diameter.
•Baffle cut of 25%-35% is usually recommended.
Types of Baffle Plates
Double Segmental Baffles
Triple Segmental Baffles
The triple segmental baffles are used for low pressure

applications.
Disc and ring baffles are composed of alternating outer rings

and inner discs, which direct the flow radially across the tube
field.
The potential bundle-to-shell bypass stream is eliminated
This baffle type is very effective in pressure drop to heat
transfer conversion
In an orifice baffle shell-side-fluid flows through the

clearance between tube outside diameter and baffle-hole
diameter.
Therm-Hydraulic Analysis of Heat Exchanger
• Initial Decisions.
• Tube side Thermal Analysis.
• Thermal analysis for Shell side.
• Overall Heat Transfer coefficient.
• Hydraulic Analysis of Tube side.
• Hydraulic Analysis of Shell side.
Fluid Allocation : Tube Side
• Tube side is preferred under these circumstances:

• Fluids which are prone to foul
• The higher velocities will reduce buildup
• Mechanical cleaning is also much more practical for tubes than for
shells.
• Corrosive fluids are usually best in tubes
• Tubes are cheaper to fabricate from exotic materials
• This is also true for very high temperature fluids requiring alloy
construction
• Toxic fluids to increase containment
• Streams with low flow rates to obtain increased velocities and
turbulence
• High pressure streams since tubes are less expensive to build strong.
• Streams with a low allowable pressure drop
Fluid Allocation : Shell Side
• Shell side is preferred under these circumstances:

• Viscous fluids go on the shell side, since this will usually
improve the rate of heat transfer.
• On the other hand, placing them on the tube side will
usually lead to lower pressure drops. Judgment is needed.
• Low heat transfer coefficient:
• Stream which has an inherently low heat transfer coefficient
(such as low pressure gases or viscous liquids), this stream
is preferentially put on the shell-side so that extended
surface may be used to reduce the total cost of the heat
exchanger.
Options for Shell-Side Thermal Analysis
• Kern's integral method
• Bell-Delaware method
• Stream analysis method
• Recent Methods
Kern Method of
SHELL-AND-TUBE HEAT EXCHANGER Analysis
Knowledge for Solving True Industrial Problems :
Donald Q Kern
• True believer of providing knowledge for use of solving
run-of-the-mill problems.
• Donald Q. Kern Award: AIChE.
• In honor of Donald Q. Kern, pioneer in process heat
transfer, the Division recognizes an individual's expertise
in a given field of heat transfer or energy conversion.
• There is no true flow area by which the shell-side mass
velocity can be computed.
• Fictitious values for equivalent diameter and mass velocity
are to be defined.
• These are borne out by experiment.
Flow Past Tube Bundles : Outside Film Coefficient
Kern’s Integral Method
• The initial attempts to provide methods for calculating shell-

side pressure drop and heat transfer coefficient were based on
experimental data for typical heat exchangers.
• One of these methods is the well-known Kern method, which
was an attempt to correlate data for standard exchangers by a
simple equation analogous to equations for flow in tubes.
• This method is restricted to a fixed baffle cut (25%) and
cannot adequately account for baffle-to-shell and tube-to-
baffle leakages.
• Although the Kern equation is not particularly accurate, it does
allow a very simple and rapid calculation of shell-side
coefficients and pressure drop to be carried out
Major Steps in Design
• Initial Decisions.
• Tube side Thermal Analysis.
• Thermal analysis for Shell side flow.
• Overall Heat Transfer coefficient.
• Hydraulic Analysis of Tube side.
• Hydraulic Analysis of Shell side.
Initial Decisions
• Spatial allocation of fluid.

• Determination of flow velocity.
• Initial guess for number of tubes.
• Correction for standard tube diameter.
• Effect of number of tubes on tube length….

A Crisis of More Area Than The Required Heat Exchanging Surface Area

Uploaded by

Copyright:

Available Formats

A Crisis of More Area Than The Required Heat Exchanging Surface Area

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

A Crisis of More Area Than The Required Heat Exchanging Surface Area

Uploaded by

Copyright:

Available Formats

A crisis of More Area than the Required Heat

Exchanging Surface Area

• Shell and tube heat exchangers are the most widespread

• It is mechanically rugged enough to withstand normal shop

• It is essential for the designer to have a good working

Double Segmental Baffles

Triple Segmental Baffles

The triple segmental baffles are used for low pressure

Disc and ring baffles are composed of alternating outer rings

In an orifice baffle shell-side-fluid flows through the

• Tube side is preferred under these circumstances:

• Shell side is preferred under these circumstances:

• Kern's integral method

• Stream analysis method

• The initial attempts to provide methods for calculating shell-

• Spatial allocation of fluid.

You might also like