Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Chapter 5 Wings and Tailplane

Download as ppt, pdf, or txt
Download as ppt, pdf, or txt
You are on page 1of 52

Airframes

Chapter 5: Wings & Tailplane

1
2
Learning Objectives
The purpose of this chapter is to discuss in more detail, 2
of the 4 major components, the Wing (or mainplane) and
the Tailplane.

By the end of the lesson you should have an


understanding of the main functions of this most important
of the main components of an aircraft, as well as it’s
construction.

But first a recap of Chapter 4 with some questions.

3
Chapter 4 Revision
A few questions about the previous chapter.

1. Why are windows elliptical?

2. What is a Welded Steel Truss?

3. Why do we pressurise the fuselage?

4. What parts of a Combat Aircraft are pressurised?

4
The Wing
From ‘Principles of Flight’, you will know that to fly, an
aircraft must have wings designed to generate lift from the
airflow over them.

To take off and climb, the wings must produce more lift
than the aircraft’s total weight.
– For an aircraft such as the Airbus A380, which weighs 550
tonnes, this is no mean task.

If a fighter aircraft was to fly in a very tight turn, the wings


must then produce lift equal to perhaps eight times the
aircraft weight.

5
The Wing
For level flight the lift produced must equal the aircraft’s
weight.
For landing, where the slowest possible landing speed is
required, enough lift must be produced to keep the aircraft
flying at low speeds.
– For this it will normally have special devices added - flaps,
leading-edge slats

The shape of the aircraft is extremely important, because


it dictates how well the aircraft can does its job. For a
slow-flying aircraft which needs to lift heavy loads, a large
wing is needed, together with a fairly light structure. For
fast jets, a much smaller wing is required, and the aircraft
will be more streamlined.
6
Wing Loading
One of the most important factors in an aircraft design is
its wing loading, which is simply its weight divided by its
wing area.

The weight of the aircraft can vary, both with the load it is
carrying and as a result of flight manoeuvres
– Flying at 4g in a turn increases an aircraft’s effective weight to
four times its normal weight, so its wing loading will change.

A useful guide is to use the maximum take-off weight


(MTOW) to calculate a ‘standard’ wing loading.

Light aircraft will normally have the lowest wing loading,


and fast jets the highest, with transport aircraft in between. 7
Design Considerations
For aircraft flying at, or near supersonic speeds, the way
in which air flows over the aircraft is very different, and
can create problems.

An aircraft flying quite slowly through the air generates


pressure waves, which move at the speed of sound.
At speeds near the speed of sound a shock wave forms
on the leading parts of the aircraft. The air behind this
shock wave becomes turbulent, causing loss of lift,
increased drag, changes in trim and buffeting of controls. 8
Sweep-Back – The Solution
Designers can reduce the effects of these problems with
better designs, particularly swept-back wings.

However, these features can cause other problems,


because they are more difficult and expensive to build.
– Once above the speed of sound, the airflow is steady again,
although different to subsonic conditions.

The curved shapes that worked well at lower speeds are


no longer the most efficient, and straight lines and sharp
edges are now preferred.

9
Wing Planform
The planform of wings becomes more important than
their section, and low aspect ratio and sharper
sweepback may be necessary.

The main disadvantage of swept-back wings is that they


produce much less lift than an un-swept wing of the same
area and aspect ratio.
– This means that when the aircraft is flying slowly, for instance
during landings, a larger angle of attack is required to provide
enough lift.

This can cause problems with landing gear and in pilot


visibility.
10
Swing Wings
Being able to change the amount of sweepback in flight
would be a way towards getting the best in both situations.

This has been done on many high speed military aircraft


– In the swept forward position it gives high aspect ratio wing for
low-speed performance, allowing tight turns at low speeds and
making flaps more effective for take-off and landing.

– In the swept back position, it is highly suited to high-speed


flight.

11
Delta Wings
Another option for aircraft which need to fly at high speeds
but also need to be able to turn tightly at all speeds is the
delta wing.
– This has the advantage of high sweepback, but the trailing
edge is more suited to fitting effective flaps.

Because of the aerodynamics of delta wings, they are


capable of producing lift at much higher angles of attack
than other wing shapes, and so can be used on highly
agile fighter aircraft.
Delta wings, which went out of fashion in the 1970s and
1980s, are becoming more common. Many examples can
be seen, often in conjunction with Canard Foreplanes for
control.
12
Aspect Ratio
The aspect ratio of an aircraft’s wing is an important
design feature, and is simply the ratio of the wing span to
its average chord.
This is not always simple to calculate if a wing shape is
complex, so another way of defining it is;

Aspect Ratio = Span 2

Area

So if a wing has an area of 80 square metres and a span


of 20 metres the aspect ratio is (202/80 = 5).
It is usual to use the projected area to calculate the aspect
ratio, that is, to include that part of the wing which is inside
the fuselage. 13
Aspect Ratio - Examples
High performance sailplanes have aspect ratios in the
region of 25 to 30, and fighters somewhere around 5 to
10.

High aspect ratio reduces the induced drag caused by air


flowing around the wing tips, and is ideal where long slow
flights are required.
The drawback is that long, thin wings need to be heavier,
and are very flexible.
14
Monoplanes
Although there are still a few bi-planes around, most
aircraft are monoplanes. This provides a very stiff, strong
wing, without the drag penalty of the biplane arrangement.
Many light aircraft are braced
monoplanes, having a
diagonal bracing tie between
the wing and fuselage.

This allows a lighter structure


in the wing, because some of
the lift load is taken by the
brace. The extra drag caused
is acceptable at low speeds.
15
Cantilever Monoplanes
The cantilever wing is used for aircraft of all speeds,
because it offers the lowest drag.
The wings have to be strong enough and stiff enough to
carry the whole weight of the aircraft, plus its aerodynamic
loads, without the need for external bracing.
They can be categorised as;
– Low Wing: Grob 115E ‘Tutor’

– Mid Wing: Gen Dyn F-16

– High Wing: BAe Harrier GR9


16
Wing Functions
Obviously the primary function of the wings on an aircraft
are to provide the lift required to enable it to fly.

However, what other functions do you think a wing is


expected to do?
Car
ry F ue l ry W
Ca r g
& S eapon an di n
tr y t ores s e L
m e t h
G eo o use ear
g e Ho H G
n us
Cha e Eng
ines

As you can see, the wing can sometimes do lots of jobs


as well as providing lift!
17
Flying Wings
So we can see that the wings are the main component of
an airframe. In fact, aircraft have been designed and built
which consist only of a pair of wings like the Northrop
‘Flying Wing’.

18
Flying Wing Compromise
A more common compromise can be seen in aircraft like
the Boeing B2 ‘Spirit’ , F-117A ‘Nighthawk’ and delta
aircraft like Concorde.

19
Wing Loads & Forces
The wing is subject to a number of loads and forces, both
whilst the aircraft is on the ground and when it is in the air.
– When an aircraft is moving through the air, the ‘drag’ effect
from the air to it’s forward motion places a force on the wing.

– Likewise, the act of the wing in generating lift also places


forces on the structure.

– On the ground, the weight of the fuel, undercarriage, engines,


wing structure and in military aircraft – weapon loads will all try
and bend the wing under the force of gravity.

The designer has to make the wings strong and stiff


enough to resist not only the forces of lift and drag, which
try to bend them upwards and backwards, but also the
loads that gravity will place on the structure. 20
Methods of Construction
As you have already seen, different sizes and types of
aircraft can be constructed in different ways.

This applies to the mainplanes, or wings, as much as to


any other part.

Can you think of component parts of the structure that


make up a complete wing?

Skin Flaps
Spars
Ailerons
Ribs
21
Methods of Construction
Each wing is basically made up of two parts;
– The internal structure, such as the spars and the ribs
– The skin, which can be of fabric, metal or composites.

Although the distinction between metal and composite


wings may not be very apparent in modern fast jets or
large transport aircraft.
Wing construction itself comes in two forms. The modern
Stress Skin standard and the older Fabric Covered wing.
However, both forms of construction rely on a similar
internal construction.

22
Fabric Covered Wings
The main structural members, as for most aircraft wings,
are the front and rear spars, which are attached to each
other by a series of ribs.
– Ribs give the wing it’s section, and transfer loads from the
covering into the spars.
Leading Edge Ribs

Extra Nose
Ribs Rear Spar

Front Spar
Trailing
Edge
Attached to the front spar is the leading edge section, in
this case made up of nose ribs and the leading edge itself. 23
Fabric Covered Wings
The trailing edge section is similar, but of a different
shape, and contains the ailerons and flaps.
Although the fabric covering takes very little load, it does
strengthen and stiffen the structure a little, especially in
torsion (twisting).
The main structural ribs help to support the fabric to keep
a good aerodynamic section along the whole wing.
Along the leading edge, where the aerodynamic section
curves most, extra nose ribs are added to make sure this
important part of the wings is not upset by sagging of the
covering fabric.

24
Stressed Skin Wings
Air loads on the wing increase at the square of the speed
increase.

For instance, at 400 knots the air loads are four times as
great as the 200 knots achieved by the fastest of light
aircraft.
– The Eurofighter Typhoon easily reaches speeds in excess of
1200 knots.

Fabric covered wings cannot meet these higher loads, and


so a more rigid ‘Stressed’ skin must be used.
– Aluminium alloys are most often used for this, but composite
materials (carbon fibre) are now becoming more common.
25
Stressed Skin Wings
Both aluminium alloy and composite provide a smoother
finish and more contour to the shape than a fabric
covering, but if it is very thin it does not give much extra
strength.

If the skin is thicker, it can share the loads taken by the


structure underneath, which can then be made lighter.

Almost all aircraft have their structure made entirely in


metal, or a mixture of metal and composite materials.

The main spars are still the main strength members, but a
large contribution to the strength is made by the skin.
26
Stressed Skin Construction
In a Stressed Skin wing, the whole wing is normally of
metal construction, although the wing tip, ailerons and
leading edge may be of composites.
– As the use of composites increase, more and more of the
airframe will be made this way.

To reduce weight the ribs (both metallic and composite)


may have large lightening holes, with flanged edges to
keep the required stiffness.
The skin may be fixed to the internal structure by rivets
and bolts, as shown on the following diagram, or by
bonding (gluing), using special adhesives.

27
Stiffening Stringers
The stressed wing skin must be stiffened to prevent
buckling between the ribs.

A simple solution is to add stringers which would be


bonded or riveted to them, or integrally machined.

Stringers to stiffen
the skin
28
Question?
So with all that structure, what do you think the space
between the front and rear spar could be used for on this
type of wing?

The volume between the


front and rear spars is often
used for storing fuel, and
holes in the ribs allow the
fuel to flow inside this
space.

29
Leading & Trailing Edges
There are also spaces in the leading and trailing edges i.e.
in front of and behind the spars.

What do you think could be put in these spaces?

l es Hyd
lCab Hot A raul
t ri ca ir ic P
Elec ipes
Fuel Other Equipment

The leading- and trailing-edge sections are used for


carrying electrical cables, control wires and other items
along the wing.

30
So Why Choose Stressed Skin?
Stressed skin wing construction is generally chosen as it
allows thin cantilever wings to be produced.

These are strong enough to resist the tension,


compression and twisting loads caused by high speeds.

Therefore a wing of stressed skin construction is the


ONLY option for an aircraft that travels at medium to high
speeds.

31
Spar Design
An ideal spar is given depth so it may resist the bending
forces that are imposed on it.

An example of this is an ordinary measuring ruler, which


will flex easily when loaded on its top or bottom surfaces,
but is very stiff when a load is applied to the edge.

Now you try!

32
Typical Spar Sections
Three typical spar sections are shown in pictures below.

A & B are made of sections fastened together, but some


modern aircraft would have the spar made from a single
piece of metal, as in C, making it stronger and lighter.

Of course, this means it has to be


made more accurately, as no
‘adjustments’ can be made during
assembly.

Also in examples A and B shown, the flanges could be


made as part of the skin, if the skin is machined from a
thicker material. 33
High-Speed Flight Spars
However, for high-speed flight, a thin wing is needed, but
it may not be possible to get a deep enough spar for the
wing to cope with the stresses placed upon it.

To make the wing strong enough, more than one spar will
be used. Using two spars is quite usual on many aircraft
and is referred to as a multi-spar wing. 34
Multi-Spar Wing Example
Supersonic aircraft, such as the Eurofighter Typhoon,
require extremely thin wings, and hence use a multi-spar
layout

35
Torsion Box
Most modern large aircraft use two main spars, with
stressed skin between them, to form a torsion box
construction. The example below also has a centre spar.

The leading and trailing edge


sections are then added in a
lighter construction, and carry
very little of the loads applied
to the wing.

The major advantage of this is that, as mentioned earlier,


the space within the torsion box is an ideal space to store
fuel.
36
Wing Assembly
The whole volume is sealed using special compounds to
prevent leakage, and may be divided up into several large
tanks, so that the fuel may be moved around as required
to balance the aircraft or reduce loads in flight.
Front
Spar The image to the left is
of the assembly of an
Airbus wide-body wing.

Stringers Easy to see is the front


and centre spars (the
rear spar is not visible),
the ribs and the
Ribs Centre Spar stringers. 37
Airbus A320 Wing Sub-Assemblies

38
Machined Skin
As an alternative to making stressed skins by fastening
stringers to the skin (fabricated), the skin, stringers and
spar flanges can all be machined from a single piece of
alloy, called a billet.
This billet may be many metres long, since it is possible
to make the skin for one wing in a single piece.
The billet is much thicker and heavier then the final
machined skin.
During the manufacture of the machined skin, up to 90%
of the billet will be removed during machining!
Although this is more expensive, in both material and
machining cost, the final result is a lighter and stronger
skin than a fabricated one. 39
Advantages of Machined Skin
The advantages of using Machined Skin in an airframe
design are;
– Riveting is no longer required, so a smoother surface can be
achieved – providing a better aerodynamic wing.

– The resultant wing has a lighter structure and a more even


loading than an equivalent fabricated wing.

– Computer-controlled machining means mistakes or faults are


less likely, and more easily detected.

– Allows for easy inspection during manufacture and in service.

– Little or no maintenance is required.

– Fuel spaces are easily sealed. 40


Disadvantages of Machined Skin
However, there are some disadvantages to utilising
Machined Skin in airframes
– The associated high cost of manufacturing – particularly the
tooling set-up costs

– Battle damage repair in combat aircraft with machined skin


wings can be more difficult.

– Careful design is needed in order to maintain fail safety by


limiting spreading of fatigue cracking.

41
The False Spar
As they are very different in shape to other types of wing,
delta and heavily swept wings have different construction
to other wings.

Delta wings have a very high chord at the wing root, and
so thickness for structural stiffness is not a problem.

Swept wings may have to house the undercarriage when it


is retracted, and the sweep means that it must be located
near to the trailing edge.

42
The False Spar
A solution to this is to add another short spar (or false
spar) and to increase the chord of the wing at the root.

This then gives enough depth in the wing to fit the


retracted undercarriage, and provides a strong point for
the undercarriage mounting.
Centre Spar
Front Spar Rear Spar

U/C Attachment

‘False’ Spar
43
Undercarriage Attachment

Additional Ribs
Rear Spar

Landing Gear
Attachment Points

‘False’ Spar

44
Undercarriage Attachment

Rear Spar

‘False’ Spar

Landing Gear
Attachment Points
45
Tailplane
Tailplanes on light aircraft
may be built in a similar
way to a fabric-covered
wing.
Stressed-skin tailplanes are
usually similar in
construction to stressed-
skin wings, but they are
obviously smaller and
usually have a different
section, because they are
not required to produce lift
in normal flight.
46
The Fin
The picture on the right Ribs
shows how the fin on a
Harrier is constructed.

As you can see, the


construction of the fin is
similar to that of the
tailplane. Stressed
skin
– The fin consists of ribs,
spars and skin panels.

Spars

47
Tailplane & Fin Configurations
Designers have tried many
different configurations of
Tailplane & Fin over the
years.

On the right is the Tailplane


& Fin of a Lockheed Super
Constellation.
– As you can see, instead of
a large rudder, it has 3
smaller units.

48
Tailplane & Fin Configurations
On large aircraft, the fin may
also contain fuel.
Not only does this increase the
fuel capacity, but it also allows
for trimming of the aircraft by
transfer of weight rather than
by deflecting aerodynamic
control surface, and so
reduces drag.
Another configuration, is the ‘T’ tail – such as the VC-10.
– This is where the tailplane is mounted on top of the fin

49
Foreplanes
Foreplanes are of similar construction to tailplanes, but
are generally smaller in size.
– Because of their smaller size, foreplanes lend themselves to
being made of composite materials

They are almost always ‘all-flying’, that is, the entire


foreplane moves to provide the control movements.

Typhoon foreplane ‘At Rest’ Typhoon foreplane ‘At Work’


50
Conclusions
As has been seen, the wing is not only the most important
part of the airframe, but it is also one of the most complex.

As technology advances, so the designers of wings will


create evermore efficient wings.

Even so, the underlying structure of the wing has not


changed in many years. Methods of constructing the wing,
and the materials it is made from are the factors that are
changing most.

Any Questions ?

51
Questions
Here are some questions for you!

1. Name 2 parts of a wing?

2. What is an alternative to making a stressed skin by


fastening stringers to the skin?

3. If an aircraft increases it’s airspeed from 200 knots to


600 knots, how much higher will the air loads on the
wing be?

52

You might also like