Electrical Tools and Equipments

WHAT DO
YOU NOTICE
IN THE
PICTURE?
ELECTRICAL INSTALLATION AND
MAINTENANCE
ROBERT S. PUGAYAN JR.

•Ampere - a unit of measure of electric current
• Circuit - the path of electric current from the source to the components
and goes back to the source
•Kilowatt - a unit of power which is equivalent to 1000w
•Conductor - a wire or a cord which provides path for current flow
• Resistance - the quality of electric current measured in ohms that resist

the flow of current
Hot wire - a wire through
which current flows Corrugated plastic conduit
• Insulator – material used to cover Tools - are implements used to
(CPC) - commonly known as
electric wires which may be made modify raw materials for
flexible non-metallic conduit
from plastic, rubber, or asbestos. human use
or the “moldflex”
Metallic Conduits- metal

raceways that was classified Non-metallic conduits- plastic
Connectors and Adapters -
into four; rigid steel conduit conduits or raceways designed
accessories that are used to
(RSC), intermediate metallic to be a channel of wire that are
connect from boxes to
conduit or tubing (IMC or classified as; rigid non-metallic
conduits or raceways to the
IMT), electrical metallic conduit or the PVC, the
other boxes in the electrical
conduit or tubing (EMC or flexible non- metallic or CPC,
system
EMT) and the flexible metallic and the surface plastic molding
conduit (FMC)
Electrical Tools and Equipment
Electrical task can be accomplished systematically to save

time, effort, and resources. Most of the work cannot be done
using bare hands. To do the task, electrical tools or equipment
are needed to perform the job. This lesson will discuss the
function/use of each tool or equipment used in electrical wiring
installations.
The following are common electrical tools and equipment
needed in the installation of electrical wiring.
I. SCREW DRIVERS. These tools
are made of steel hardened and
tempered at the tip used to
loosen or tighten screws with
slotted heads. They come in
various sizes and shapes.
A. Standard/Flat Screw Driver.

The blade tip is wedge-shaped
and resembles a negative (-)
sign. This is used to drive
screws with a single slot head.
D. Allen Screw Driver/Wrench.
This could be in the shape of a
screw driver or a wrench. Its
function is to drive screw with
hexagonal slot head.
II. HAMMERS. These are tools used in

driving or pounding and pulling out nails.
They are made of hard steel, wood,
plastic or rubber. The following are types
of hammer:
A.Claw hammer
B.Mallet(rubber head)
C.Ballpeen hammer
PLIERS. These made from metal with
insulators in the handle and are used
for cutting, twisting, bending, holding,
and gripping wires and cables.
A. Combination Pliers (Lineman’s

Pliers). This is used for gripping,
holding, and cutting electrical wires
and cables and even small nails. They
are usually used by linemen in doing
heavy tasks.
B. Side Cutting Pliers. This
type of pliers is used for
cutting fine, medium and big
wires and cables.
C. Long Nose Pliers. This is used for

cutting and holding fine wires. This
can reach tight space or small
opening where other pliers cannot
reach and also used in making
terminal loops of copper wires.
IV. Wire Stripper- A tool
used for removing
insulation of medium
sized wires ranging from
gauge #10 to gauge #16.
V. Electrician’s Knife. This is used
by linemen to remove insulation of
wire and cables in low and high
voltage transmission lines.
VI.Portable Electric drill. A small drilling machine with
a chuck capacity of ¼‖ to 3/8‖. It is used in making
holes on metal sheets and concrete walls.
Hacksaw. This tool is
used to cut metal conduit
and armored cable.
WHAT HAVE YOU
LEARNED?
Directions: Read the statement carefully and
identify what is being described or defined.
Choose your answer from the words inside the
box.
Long Nose Pliers Circuit Breaker Hammer
Electrician’s Knife Utility box Portable Electric Drill
Philips Screw Connectors Wire Stripper
Driver
Male Plug Fuse Combination Junction Box
Pliers
Stubby Screw
Driver Conduits
1. This is used for griping, holding, cutting electrical wires and cables and even
small nails. Usually used by linemen in doing heavy tasks.
2. Used for cutting and holding fine wires. This can reach tight space or small
opening where other pliers cannot reach and also used in making terminal loops of copper
wires.
3. This has a cross tip resembling a positive (+) sign. It is used to drive screws
with cross slot heads.
4. This is tools used in driving or pounding and pulling out nails.
5. A tool used for removing insulation of medium sized wires ranging from
gauge #10 to gauge #16.
6. A small drilling machine with a chuck capacity of ¼‖ to 3/8‖. It is used in

making holes on metal sheets and concrete walls.
7. Comes in either Standard or Philips screw driver with short shank or blade
and shorted handle used to turn screws in tight space where standard screw driver cannot
be used.
8. Used by linemen to remove insulation of wire and cables in low and high voltage
transmission lines.
9. Is a device inserted to a convenience outlet to conduct electric current. A flat cord is

attached to it on one end and the other end is connected to a current consuming instrument or appliance.
10. This is a circuit protective device that automatically blows and cut the current when an
over load or short circuit happens.
11. This is a rectangular shaped metallic or plastic (PVC) material in which flush type
convenience outlet and switch are attached.
12. Are electrical materials used as the passage of wires for protection and Insulation.
13. Are used to attach metallic or non-metallic conduit to the junction or utility boxes.
14. This is a protective device used to automatically cut off the current when trouble in the
circuit such as short circuit or over load occurs.
15. Is an octagonal shaped electrical material where the connections or joints of wires are
being done. It is also where the flush type lamp holder is attached.
THANK YOU!

Electrical Tools and Equipments

Uploaded by

Copyright:

Available Formats

Electrical Tools and Equipments

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Electrical Tools and Equipments

Uploaded by

Copyright:

Available Formats

WHAT DO

ROBERT S. PUGAYAN JR.

•Kilowatt - a unit of power which is equivalent to 1000w

•Conductor - a wire or a cord which provides path for current flow

• Resistance - the quality of electric current measured in ohms that resist

Metallic Conduits- metal

Electrical task can be accomplished systematically to save

A. Standard/Flat Screw Driver.

II. HAMMERS. These are tools used in

A. Combination Pliers (Lineman’s

C. Long Nose Pliers. This is used for

4. This is tools used in driving or pounding and pulling out nails.

6. A small drilling machine with a chuck capacity of ¼‖ to 3/8‖. It is used in

9. Is a device inserted to a convenience outlet to conduct electric current. A flat cord is

You might also like