Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
16 views

Lecture 4

The document discusses pressure buildup tests for analyzing reservoir properties. It describes the assumptions and equations for an ideal buildup test in an infinite, homogeneous reservoir with single-phase fluid. Deviations from these assumptions in real reservoirs are also discussed. These include the reservoir having finite boundaries, multiphase fluids, and heterogeneity. Corrections such as the MDH method and other models are needed to analyze buildup tests in more complex, non-ideal reservoirs.

Uploaded by

mohammed.bm106
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
16 views

Lecture 4

The document discusses pressure buildup tests for analyzing reservoir properties. It describes the assumptions and equations for an ideal buildup test in an infinite, homogeneous reservoir with single-phase fluid. Deviations from these assumptions in real reservoirs are also discussed. These include the reservoir having finite boundaries, multiphase fluids, and heterogeneity. Corrections such as the MDH method and other models are needed to analyze buildup tests in more complex, non-ideal reservoirs.

Uploaded by

mohammed.bm106
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 25

Flow for generalised

reservoir geometry
• Pseudo-steady-state solution to the flow equation
assumed a centred well in a circular drainage area.

• There is an equation that models pseudo-steady-state


flow in more general reservoir shapes:
• For a given reservoir geometry, the maximum time a reservoir is invite
acting can be determined using the entry in the column “ infinite-
system with less than 1% error for tDA <

• tDA

• This means that time in hours can be calculated

• Time required for the pseudosteady-state equation to be within 1%


accuracy we used the entry “less than 1% error for t DA >

• Finally time required for the pseudosteady-state equation to be exact is


found from “ exact for tDA >
Example (1)

• For each of the following reservoir geometries, calculate


the time in hours for which (a) the reservoir is infinite
acting (b) the pseudo steady state is exact and (c) the
pseudo steady state equation is accurate within 1%. (1)
Well centred in circular drainage area (2) Well is centred
in square drainage area and (3) well centred in one
quadrant of square drainage area.
Solution (1)
• In each case we have:-

• A=17.42x10^6 sq ft (40 acres)

• 𝜙=0.2

• 𝜇= 1cp

• Ct = 1x10^-5 1/psi

• k= 100 md
• We first calculate the time group tDA (dimensionless time based on
drainage area)

• Now we prepare the following table.


Introduction to Buildup tests
analysis
• We developed basic equations for describing the pressure
behaviour in an oil reservoir. Now we need to apply them
in analysing pressure buildup curves/tests.

• In a buildup test, a well which is already flowing (ideally


at constant rate) is shut in. And the bottom hole pressure
measured as the pressure builds up.

• It is easy because the constant flow rate condition is easily


achieved. (0)

• Disadvantages ( production is lost during test, It may be


difficult to achieve the constant rate production prior to
the shut in.
• Suppose after producing a well at a constant rate for a certain length of time
we decide to shut it in for pressure buildup. Intuitively, we expect fluid
movement to continue in the reservoir after shutting the well in. The fact that
we shut in the well means that (q=0) at the wellhead. We account for the
fluid movement which continues in the reservoir after the well is shut in as
follows:

• First we produce the well at a constant rate for some time.

• Shut the well in at the surface

• Allow the pressure to build up in the wellbore

• Record the pressure in the wellbore as a function of time.

• We can estimate formation permeability and drainage area pressure etc.


The Ideal Buildup test
• By Ideal we mean test in an infinite, homogeneous,
isotropic reservoir containing slightly compressible
single phase fluid with constant fluid properties ( so the
Ei function and its approximation applies). One last
assumption is the pseudo-producing time is applicable.

• If a well has produced for a time tp at rate q before shut


in, and if we call time elapsed since shut in 𝛥t, then using
the superposition equation we find that:-
• This equation suggests that the shut in BHP, Pws
recorded during a pressure build up test should plat as a
straight line function of log[(tp+𝛥t)/𝛥t], and that the
slope of this line is the constant group
• The formation permeability can thus be calculated from a buildup test by measuring
the slop m.

• Conventional practice in the industry is to plot Pws vs(tp+𝛥t)/𝛥t on


semilogarithmic paper with values of (tp+𝛥t)/𝛥t decreasing from left to right.
• We can also determine skin factor s from the data available in the idealised
pressure buildup test.

• At the shut in time 𝛥t in the test we have:-


• Now combining and solving for s we

• It is customary in the petroleum industry to choose a


fixed shut in time 𝛥t of 1 hour and the corresponding
shut in pressure P for the above equation.

• to simplify the equation by assuming =1


Ideal Pressure build up test
Example.

• Unknowns ( k, Pi and S)
• It is a pressure build up test thus we use the formula

• We first have to plot Pws vs in a semiolog paper

• Measure the slop m and calculate k.

• Extrapolate the curve to infinite shut in time, and read the


reservoir original pressure Pi.

• Skin factor equation can be used to calculate s.


•Wecan test if this is an ideal pressure build up test by
examining that the plotted curve yields a straight line. thus

•We pick any two points on the line and subtracting the
pressures ( that are one cycle apart i.e. factor of 10)
Producing time tp=72 hr
Slope m= (1950-1850)= 100 psi/cycle

k=

Pi can be found by the extrapolation of


line to =1

Pi=1950 psig
skin factor can be calculated from

Here Pws (pressure at shut in) is P1hr on the line and can be found at =73

Pws=1764 and hence;

=1.43 (well has a flow restriction).


Actual Buildup Tests
• When ideal build up test used in an actual well, discouraging
results were faced and thus a correction is needed. Thus,
instead of obtaining a single straight line, we get a
complicated curve.

• This curve can be divided into 3 regions

• Early-time region

• Middle-time region

• late-time region
Deviations from Assumptions
in Ideal theory

• 1) Infinite reservoir

• 2) Single phase liquid

• 3) Homogeneous reservoir.
Infinite reservoir
• We can conclude that the Horner plot and approximation isn’t valid if
the reservoir is not infinite acting. A reservoir with no apparent outer boundary limit
affecting fluid flow during a test period. Unless an outer boundary, such as a nearby fault, is close to the
wellbore, it usually takes a day or more for outer boundaries to affect well-test results. Since most tests
are of relatively short duration, outer boundaries usually do not affect test results” Schlumberger
glossary.

• We assumed that the reservoir is infinite acting just before the build up test and during the test. We
can’t use the infinite reservoir solution with Ei function and its simplification (ln)

• There are methods (by different analysts) to resolved this issue when the reservoir isn’t infinite acting.
Finite acting reservoir
• We will use MDH method.
Single phase liquid assumption
• We know that

• Even in single phase flow


Homogeneous Reservoir
Assumption
• Solutions for the flow equation are valid for
homogeneous reservoir, yet there is no such a thing as a
homogeneous reservoir.

• When massive heterogeneities are faced in localised


portion of the reservoir, simple flow equation loses
accuracy.

• Models in the literature can be used.


Radius of investigation

You might also like