Lecture 6

Computer Networks
Lecture 6
4.1 Digital-to-Digital Conversion
• Data can be either digital or analog
• Signals that represent data can also be digital or

analog
• Conversion involves three techniques:

• line coding,
• block coding, and
• scrambling.
• Line coding is always needed;

• Block and scrambling may/may not be needed
4.1.1 Line Coding
• Line coding is the process of converting digital data to
digital signals
• At the sender,
• digital data are encoded into a digital signal;
• at the receiver, the digital data are recreated by decoding the
digital signal
Characteristics
1. Signal vs Data Element
• Data element is the smallest entity of information
• what we need to send
• Signal element carries data elements
• what we can send
2. Data Rate vs Signal Rate
• data rate defines the number of data elements (bits) sent in 1s [unit is the bps]
• signal rate is the number of signal elements sent in 1s [unit is the baud]
• Goals: increase the data rate decreasing the signal rate
• Data rate (N) and signal rate (S): S = N/r

Savg = c * N * (1/r) baud
c is the case factor, which varies for each case

3. Bandwidth
• digital signal that carries information is nonperiodic
• effective bandwidth is finite
• We can say that the baud rate determines the required
bandwidth for a digital signal
• bandwidth reflects the range of frequencies we need
• relationship between the baud rate (signal rate) and the
bandwidth.
• Bandwidth (range of frequencies) is proportional to the
signal rate (baud rate)
Bmin = c * N * (1 / r)
maximum data rate if the bandwidth of the channel is
given
Nmax = (1 / c) * B * r
4. Baseline Wandering
• In decoding, the receiver calculates a running average

of the received signal power.
• This average is called the baseline
• Incoming signal power is evaluated against this

baseline to determine the value of the data element
• A long string of 0s or 1s can cause a drift in the

baseline (baseline wandering)
• good line coding scheme prevent baseline wandering

5. Self-synchronization
• Signals received from the sender,

• the receiver’s bit intervals must same to the sender’s bit intervals
• IF not matched then receiver might misinterpret the signals
• Receiver has a shorter bit duration.

• The sender sends 10110001, while the receiver receives
110111000011.
6. Built-in Error Detection
desirable to have a built-in error-detecting capability
7. Immunity to Noise and Interference

Coding should be immune to noise and other
interferences
8. Complexity
complex scheme is more costly to implement than a
simple one
scheme that uses four signal levels is more difficult to

interpret than one that uses only two levels
4.1.2 Line Coding Schemes
1. Unipolar
• NRZ
2. Polar
• NRZ,
• RZ, and
• Biphase (Manchester,and differential Manchester)
3. Bipolar
• AMI and pseudoternary
Unipolar:
NRZ (Non-Return-to-Zero)
• positive voltage defines bit 1 and
• the zero voltage defines bit 0
• signal does not return to zero at the middle of the bit
• scheme is very costly than polar counterpart
• not used in data communications nowadays
Polar: Voltage level for 0 can be positive and
• the voltage level for 1 can be negative
NRZ (Non-Return-to-Zero): Two versions of polar NRZ
• NRZ-L (Level)
• level of the voltage determines the value of the bit
• NRZ-I (Invert)
• change or lack of change in the level of the voltage determines the
value of the bit
• If no change, the bit is 0; Else the bit is 1
Return-to-Zero (RZ)
• NRZ encoding issue: when the sender and receiver clocks are
not synchronized
• receiver does not know when one bit has ended and the next bit is
starting
• One solution is the return-to-zero (RZ): three values:

• positive, negative, and zero
• signal changes not only between bits but also during the bit
• Disadvantage: it requires two signal changes to encode a bit;

occupies greater bandwidth
Biphase: Manchester and Differential Manchester
Manchester : The idea of RZ and the idea of NRZ-L are combined
• the duration of the bit is divided into two halves

• voltage remains at one level during the first half and moves to the other
level in the second half
• transition at the middle of the bit provides synchronization
Differential Manchester combines the ideas of RZ and NRZ-I
• a transition at the middle of the bit, but the bit values are determined at
the beginning of the bit
• If the next bit is 0, there is a transition; if the next bit is 1, there is none
• Minimum bandwidth of Manchester and differential Manchester

is 2 times that of NRZ
4.2 Analog-To-Digital Conversion
• An analog signal such as one created by a microphone

or camera:
• to change an analog signal to digital data
• Two techniques (Digitization

• pulse code modulation (PCM) and
• delta modulation (DM)
4.2.1 Pulse Code Modulation (PCM)
Three steps:
1. The analog signal is sampled.
2. The sampled signal is quantized.
3. The quantized values are encoded as streams of bits.
SAMPLING:
• The analog signal is sampled every Ts s,
• where Ts is the sample interval or period.

• The inverse of the sampling interval is called the sampling rate
or sampling frequency and denoted by fs, where fs = 1/Ts.
SAMPLING RATE:
According to the Nyquist theorem,

the sampling rate must be at least 2 times the highest
frequency contained in the signal
QUANTIZATION
• The result of sampling is a series of pulses with

amplitude values between the maximum and
minimum amplitudes of the signal
• The following are the steps in quantization:

• amplitudes between Vmin and Vmax
• divide the range into L zones, each of height Δ (delta).
Δ = [ Vmax – Vmin ] / L
• assign quantized values of 0 to L − 1 to the midpoint of each
zone
• approximate the value of the sample amplitude to the
quantized values
Cont’d
• Assume a sampled signal and sample amplitudes are between −20 and +20 V
• We decide to have eight levels (L = 8). This means that Δ = 5 V.

Quantization Levels
• The choice of L depends on
• the range of the amplitudes of the analog signal and
• How accurately we need to recover the signal
• If the amplitude of a signal fluctuates between two values only,

• we need only two levels;
• if the signal, like voice, has many amplitude Values, need more
quantization levels
• In audio digitizing, L is normally chosen to be

• 256;
• in video it is normally thousands
• Choosing lower values of L increases the quantization error if

there is a lot of fluctuation in the signal
Quantization Error
• The output values are chosen to be the middle value in
the zone.
• If the input value is also at the middle of the zone,
• there is no quantization error;
• otherwise, there is an error
• In other words, we have −Δ/2 ≤ error ≤ Δ/2.
• quantization error changes the signal-to-noise ratio of the

signal,
• which in turn reduces the upper limit capacity according to
Shannon
• nb: bits per sample
SNRdB = 6.02nb + 1.76 dB

4.2.2 Delta Modulation (DM)
• PCM is a very complex technique
• DM reduces the complexity of PCM
• No code words here; bits are sent on after another
4.3 TRANSMISSION MODES
• Transmission of binary data across a link can be
accomplished in either
• parallel (multiple bits are sent with each clock tick)
• serial mode (bit is sent with each clock tick)

4.3.1 Parallel Transmission
• Send n data bits at a time instead of 1
• Use n-wires to send n bits
• High speed
• Cost penalty
• Usually limited to short distances
4.3.2 Serial Transmission
• One communication channel
• Reduces cost of transmission over parallel by roughly a
factor of n
ASYNCHRONOUS TRANSMISSION
• timing of a signal is unimportant
• information is received and translated by agreed upon
patterns
• grouping the bit stream into bytes
• The sending system handles each group independently,
• relaying it to the link whenever ready, without regard to a
timer
• To alert the receiver to the arrival of a new group,

• an extra bit is added to the beginning of each byte usually a
0, called the start bit.
• To let the receiver know that the byte is finished, 1 or more

bits are appended, usually 1s, are called stop bits.
• Asynchronous here means
• “asynchronous at the byte level,”
• but the bits are still synchronized; their durations are the same
• it is cheap and effective,

• attractive choice for situations such as low-speed communication
(Keyboard connection)
SYNCHRONOUS TRANSMISSION
• Timing becomes very important

• Bit stream is combined into longer frames
• data are transmitted as an unbroken string of 1s and 0s,

• the receiver separates that string into the bytes, or characters,
• it needs to reconstruct the information
• Without gaps and start and stop bits,

• there is no built-in mechanism to help the receiving
• no extra bits or gaps

• faster than asynchronous
• there may be uneven gaps between frames
• Byte synchronization is accomplished in the data-link layer

ISOCHORONOUS
• In real-time audio and video

• uneven delays between frames are not acceptable,
synchronous transmission fails
• TV images are broadcast at the rate of 30 images per

second;
• they must be viewed at the same rate.
• If each image is sent by using one or more frames,

• there should be no delays between frames
• Isochronous transmission guarantees that the data arrive

at a fixed rate

Lecture 6

Uploaded by

Copyright:

Available Formats

Lecture 6

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lecture 6

Uploaded by

Copyright:

Available Formats

Computer Networks

• Signals that represent data can also be digital or

• Conversion involves three techniques:

• Line coding is always needed;

• Goals: increase the data rate decreasing the signal rate

• Data rate (N) and signal rate (S): S = N/r

c is the case factor, which varies for each case

• In decoding, the receiver calculates a running average

• Incoming signal power is evaluated against this

• A long string of 0s or 1s can cause a drift in the

• good line coding scheme prevent baseline wandering

• Signals received from the sender,

• Receiver has a shorter bit duration.

7. Immunity to Noise and Interference

scheme that uses four signal levels is more difficult to

• One solution is the return-to-zero (RZ): three values:

• Disadvantage: it requires two signal changes to encode a bit;

Manchester : The idea of RZ and the idea of NRZ-L are combined

• the duration of the bit is divided into two halves

Differential Manchester combines the ideas of RZ and NRZ-I

• Minimum bandwidth of Manchester and differential Manchester

• An analog signal such as one created by a microphone

• Two techniques (Digitization

• The analog signal is sampled every Ts s,

• where Ts is the sample interval or period.

According to the Nyquist theorem,

• The result of sampling is a series of pulses with

• The following are the steps in quantization:

• We decide to have eight levels (L = 8). This means that Δ = 5 V.

• If the amplitude of a signal fluctuates between two values only,

• In audio digitizing, L is normally chosen to be

• Choosing lower values of L increases the quantization error if

• In other words, we have −Δ/2 ≤ error ≤ Δ/2.

• quantization error changes the signal-to-noise ratio of the

SNRdB = 6.02nb + 1.76 dB

• parallel (multiple bits are sent with each clock tick)

• serial mode (bit is sent with each clock tick)

• To alert the receiver to the arrival of a new group,

• To let the receiver know that the byte is finished, 1 or more

• it is cheap and effective,

• Timing becomes very important

• data are transmitted as an unbroken string of 1s and 0s,

• Without gaps and start and stop bits,

• no extra bits or gaps

• Byte synchronization is accomplished in the data-link layer

• In real-time audio and video

• TV images are broadcast at the rate of 30 images per

• If each image is sent by using one or more frames,

• Isochronous transmission guarantees that the data arrive

You might also like