This document provides a guide to developing a water-wise landscape using Xeriscape principles. It outlines seven steps: 1) Planning and Design, 2) Soil Analysis, 3) Appropriate Plant Selection, 4) Practical Turf Areas, 5) Efficient Irrigation, 6) Use of Mulches, and 7) Appropriate Maintenance. Implementing some or all of these steps can reduce outdoor water consumption by up to 50% without sacrificing beauty or quality. A water-wise landscape is environmentally friendly and low maintenance, saving both water and money.
Report
Share
Report
Share
1 of 44
Download to read offline
More Related Content
Xeriscape: a Guide to Developing a Water-Wise Landscape - University of Georgia
1. a guide to developing a water-wise landscape
Cooperative Extension
The University of Georgia College of Agricultural and Environmental Sciences
2. TABLE OF CONTENTS
Introduction........................................................................................................................................1
Step 1: Planning and Design ...........................................................................................................2
Begin With a Base Map .........................................................................................................2
Catalog Site Characteristics...................................................................................................2
Incorporate Shade Into the Design ........................................................................................3
Plan for Different Use Areas ..................................................................................................3
Establish Water-use Zones ....................................................................................................4
Develop a Master Plan...........................................................................................................5
Fit Plants to the Design..........................................................................................................6
Renovation of an Existing Landscape for Improved Water Conservation .............................6
Step 2: Soil Analysis .........................................................................................................................8
Inspect Your Soil ....................................................................................................................8
Soil Analysis Saves Guesswork.............................................................................................8
Don’t Add Organic Matter to the Planting Hole for Trees and Shrubs...................................8
Improve the Structure of Poor Soils .......................................................................................8
Step 3: Appropriate Plant Selection ................................................................................................9
Step 4: Practical Turf Areas ...........................................................................................................10
Step 5: Efficient Irrigation...............................................................................................................11
Sprinkler Irrigation ................................................................................................................11
Drip Irrigation........................................................................................................................12
Guidelines for Irrigating the Landscape ...............................................................................13
Step 6: Use of Mulches...................................................................................................................14
Step 7: Appropriate Maintenance ..................................................................................................16
Fertilize Less and Use Slow-release Fertilizers...................................................................16
Soil Testing Saves Guesswork.............................................................................................16
Avoid Shearing Plants..........................................................................................................16
Proper Mowing Saves Water ...............................................................................................16
Aerating Turfgrass Improves Water Movement ...................................................................16
Other Water-saving Maintenance Practices ........................................................................17
Summary ..........................................................................................................................................17
Georgia Hardiness Zones ...............................................................................................................18
Durable Plants for Xeriscape-type Landscapes ...........................................................................19
Commercially Designed Xeriscape-type Landscapes: Before and After Renovation ..............32
References .......................................................................................................................................40
3. a guide to developing a water-wise landscape
Prepared by Gary L. Wade and James T. Midcap, Extension Horticulturists; Kim D. Coder, Extension Forester; Gil Landry, Extension
Agronomist; Anthony W. Tyson, Extension Agricultural Engineer: and Neal Weatherly, Jr., University of Georgia Environmental
Landscape Design Department
INTRODUCTION during the summer. As a result, much water is lost to
evaporation or run-off, or it is simply wasted when
Today Georgia is facing a serious water supply plants are given more water than they need.
problem in several urban areas as population growth In this publication, you will be introduced to Xeri-
places an ever-increasing strain on available water scape™, quality landscaping that conserves water and
supplies. protects the environment.
From 1995 to 2005, Georgia’s population grew by The term Xeriscape (pronounced zera-scape) was
more than 1 million, and it is projected to increase coined in Colorado in 1981 in response to a prolonged
another 2 million by 2015. In 2007, more than two- drought. It derives from merging the Greek word
thirds of our state’s population lived in just 26 of 159 “Xeros,” meaning “dry,” with the word “landscape.”
counties. These counties are all in and around urban Today, Xeriscape programs exist in more than 40
areas. As urban areas grow, so does the competition states throughout the United States. The National Xeri-
and demand for water resources. scape Council’s headquarters is in Atlanta, Ga.
Increasing demand for water results in periodic Xeriscape-type landscaping is a package of seven
water shortages and restrictions on outdoor water use. common-sense steps for making a landscape more
Periods of limited rainfall or drought make the problem water-efficient:
worse. Recently, in some highly populated areas, water 1. Planning and Design
supply problems and restrictions on outdoor water use 2. Soil Analysis
have occurred even during times of normal rainfall. 3. Appropriate Plant Selection
Figure 1 compares water use and population 4. Practical Turf Areas
growth in Georgia from 1950 to 2000. While demand 5. Efficient Irrigation
for ground water has increased slightly, demand for 6. Use of Mulches
surface water has increased 10-fold. About 75 percent 7. Appropriate Maintenance
of Georgia’s water supply comes from surface water, Each of these steps is a good gardening practice.
while only 25 percent comes from ground water. However, the more of them you implement, the more
water efficient your landscape becomes.
A Xeriscape-type landscape can reduce outdoor
water consumption by as much as 50 percent without
sacrificing the quality and beauty of your home envi-
ronment. It is also an environmentally sound landscape,
requiring less fertilizer and fewer chemicals. And a
Xeriscape-type landscape is low maintenance — saving
you time, effort and money. Any landscape, whether
newly installed or well established, can be made more
water efficient by implementing one or more of the
Figure 1. Water use and population growth. seven steps. You do not have to totally redesign your
landscape to save water. Significant water savings can
Household water use increases dramatically during be realized simply by modifying your watering schedule,
the summer months when irrigation water is applied to learning how and when to water, using the most effi-
the lawn, garden and landscape. In some households, cient watering methods and learning about the different
water use may be as much as 100 percent higher in water needs of plants in your landscape.
summer than in winter. Let’s look at each of the Xeriscape steps in more
Tremendous amounts of water may be used out- detail.
doors. A typical portable lawn sprinkler, for instance,
applies about 300 gallons of water per hour of opera-
tion. Some residential landscapes receive several
times this amount of water two to three times a week
1
4. STEP 1: site, unusual features such as stone outcroppings and
existing vegetation. See figure 2.
PLANNING AND DESIGN Accuracy in the base map will help you determine
if your site will accommodate all of your plans. Later it
Whether you are developing a new landscape or will help to determine the quantity of any construction
renovating an existing landscape, proper planning and materials and plants needed. For additional information
design are important. You may wish to start thinking on preparing a base map, refer to Extension Leaflet
immediately about what plants to use, but first you 124, Developing a Site Plan, or talk with your county
must solve any environmental and physical problems in
Extension agent.
an attractive and practical manner. Think about the var-
ious areas of your landscape in terms of how they Catalog Site Characteristics
should be developed for different uses and how much Next, lay a sheet of tracing paper over the base
space you should allot to each area. map and label it “Site Analysis.” See figure 3. Use
As you plan each area, consider several different arrows to indicate the direction of desirable views you
arrangements. For example, is a fence, wall or hedge want to emphasize and undesirable views you want to
more appropriate for screening and/or security? How screen. Use arrows to indicate the drainage patterns of
much space is needed for active recreation, a vegeta- the property, including any low spots or eroded areas.
ble garden or for patio entertaining? Only after these Make plans to correct potential drainage problems
decisions are made should you begin thinking about before planting. This may require regrading, bringing in
what plants to use. additional soil, building retaining walls or shaping ter-
races. Any changes in the existing landscape should
Begin With a Base Map be subtle so that the natural character of the landscape
A base map is a plan of the property drawn to is retained.
scale on graph paper showing the location of the Incorporate as many of the natural elements of the
house, its orientation to the sun, other structures on the site into the design as possible, such as existing trees
Figure 2. Base map of property Figure 3. Site analysis of property
2
5. and shrubs. Undisturbed native plants will not require A person standing in an open parking lot is bom-
water for re-establishment and may be more water effi- barded with 1,000 heat units from the sun and another
cient than new plantings. 1,000 heat units reflected from the paved surface.
Note the orientation of the home (i.e., north, south, Walking beneath a shade tree provides immediate
east, west). This will help determine where to put relief from the sun because the tree acts like an
plants best suited for sun or shade. Areas exposed to umbrella, blocking light and heat (passive shade). If the
direct afternoon sun are likely to dry out more rapidly tree is growing in moist soil, it will not only block heat
than those in the shade. In these locations, your plan but will also dissipate heat by evaporative loss from the
should include drought-tolerant plants, some method of leaves (active shade). A moist soil surface also evapo-
providing supplemental water or cultural practices that rates heat and reduces heat load further. Therefore, a
will help conserve moisture. moist landscape with trees can contain one-fourth as
much heat as a parking lot in full sun and one-half as
Incorporate Shade Into the Design much heat as a bone-dry landscape.
Shade from trees or structures in the landscape In addition to paved areas, shade prevents heat
keeps the landscape cooler and reduces water loss build-up from other hardscape surfaces, such as brick
while creating a comfortable living environment. Refer or stucco walls and gravel walks. Whenever possible,
to figure 4. A shaded landscape can be as much as try to shade these surfaces.
20°F cooler than one in the full sun. Just as we perspire and lose moisture through our
pores, plants transpire and lose moisture through their
leaves. A mature oak tree, for example, can dissipate
as much heat as four home central air conditioners
running 24 hours per day. This evaporative water loss
from leaves has a cooling effect on the environment
and reduces water loss. Therefore, effective shading
makes the landscape more water-efficient, the main
objective of Xeriscape planning.
Effective shade management in a Xeriscape-type
landscape involves using shade to block sunlight from
striking the soil surface, to intercept, scatter and reflect
radiant energy to protect paved surfaces or masonry
structures from direct sunlight. Effective shade man-
agement also involves managing wind currents that
influence heat flow in the landscape. In addition to
trees, structures like trellises, arbors, walls or fences
Figure 4. A shaded landscape may be 20°F cooler can provide shade. A vine or espalier on these struc-
than a landscape in full sun. tures improves their shading and cooling effect. See
page 19 for a suggested list of vines.
Figure 5 compares the heat exchange in an un-
shaded parking lot where the soil surface is covered by Plan for Different Use Areas
pavement with a tree in dry soil and a tree in moist soil. To begin your plan, overlay the base map and site
analysis sheet with another piece of tracing paper. On
this sheet indicate the public, private and service areas
of your landscape. See figure 6. Consider how these
areas will be developed based on space requirements
for each activity.
The public area is the highly visible area that most
visitors see, such as the entry to the home. In a tradi-
tional landscape, this area typically receives the most
care, including the most water. Therefore, the careful
design of this area is important for water conservation.
This area can be designed to require minimal water and
maintenance without sacrificing quality or appearance.
The private area of the landscape, usually the
backyard, is where most outdoor activity occurs. It is
generally the family gathering area. It may also include
a vegetable garden or fruit orchard. The landscape in
this area needs to be functional, attractive and durable,
but it also should be designed to require less water
Figure 5. Effects of shade on water loss than the public area of the landscape.
3
6. Figure 6. The basic use area of a typical residential lot Figure 7. Diagram of water-use zones of property
The service area is the working or utility area of moisture stress. Possible plants for this zone include
the landscape, an area usually screened from view azalea, dogwood, redbud, Japanese maple and many
and containing such items as garbage cans, outdoor herbaceous perennials.
equipment, air-conditioning units or a doghouse. In In the low water-use zones, plants are watered by
terms of routine maintenance, this area would be natural rainfall and would not be irrigated. For greatest
designed to require the least care and water of the water conservation, design as much of your landscape
three areas. as possible into low water-use zones. Most people are
surprised to learn that the majority of our woody orna-
Establish Water-use Zones mental trees and shrubs, turfgrasses, some herbaceous
In addition to dividing the landscape into use perennials and even some annuals, like vinca and ver-
areas, a Xeriscape plan further divides the landscape bena, grow well in low water-use zones where they are
into three water-use zones: high (regular watering), not irrigated once they are established. See tables at
moderate (occasional watering) and low (natural rain- the end of this publication for additional selections.
fall). See figure 7. An individual landscape may include Expect a slight loss of quality during extended dry
several of these zones. High water-use zones are periods, but don’t be alarmed. Some plants will literally
small, highly visible areas and highly maintained areas shut down during drought and cease growing.
of the landscape, such as the public area and the area Bermuda grass will go dormant and turn brown during
around the patio where plants are watered regularly in drought, then bounce back with the first rains. Learning
the absence of rainfall. In the moderate water-use to accept this “less than perfect” appearance during dry
zones, established plants are watered only when they periods is one of the most difficult obstacles to over-
turn a gray-green color, wilt or show other symptoms of come in a water-conserving landscape.
4
7. One exception to the water zone rule is newly Develop a Master Plan
planted ornamental plants and turfgrasses. These Once you have settled on a design scheme and a
plants require regular irrigation during the establish- water management arrangement, give form and defini-
ment period (8 to 10 weeks after planting), regardless tion to the various spaces in your plan. With the identi-
of their intended water-use zone. fication of planting spaces as well as edging materials,
To maximize water savings, concentrate seasonal groundcovers and paving, the master plan begins to
color beds in areas of the landscape where they can take form. This is a plan showing the final product of
be watered and maintained. Avoid scattering a number your efforts. Straight lines or smooth flowing curves are
of small color beds throughout the landscape. best — tight curves or unnecessary bends can be
Now, add a new overlay of tracing paper to the maintenance problems. Use right angles and avoid
base map and sketch your desired water-use zones. acute angles that are difficult to maintain and irrigate.
The landscape is beginning to take shape and you can Remember that simplicity in the design will ensure
visualize the form of the various beds, but construction easy maintenance and water-use efficiency. A proto-
materials and plants have not yet been identified. type master plan is shown in figure 8.
Figure 8. Master plan for incorporating Xeriscape principles. Note how the character of this landscape is very similar to
that of a traditional landscape.
5
8. Fit Plants to the Design The redesign of the residence shows expansion of
Once you achieve the style and overall effect you the shrub beds in the public and private areas of the
desire, select plants to fill the assigned spaces. Select landscape to provide seasonal interest, variety and
plants that complement and accent the good features reduced maintenance. Shade-tolerant ground covers
of the architecture and construction materials rather are used under the existing trees on the left side of the
than overpower them. front and right rear of the property. A large area in the
Group plantings to conform to the shape of plant left rear of the property was made a natural mulch play
beds. Avoid rigid formal, geometric plantings as much as area for children. Note how the water-use zones
possible. A good approach for most residences is to place changed during the redesign of the property.
the larger plants at the corners with some height at the Tables 1 and 2 show an economic comparison of
entrance and low plantings in between. Such arrange- the landscape shown in figure 9 before and after
ments focus attention on the entrance. For a pleasing renovation. Changes in water use zones were project-
visual effect, use odd number groupings (1, 3, 5) when ed to save more than 29,000 gallons of water a year.
possible. Use bands of low-growing plants or ground cov- This equated to annual savings of $66.12 on water,
ers to tie together and unify groups of taller shrubs. $46.40 on sewage and $237.00 on landscape mainte-
Place plants at the proper spacing in the landscape nance. Although the landscape renovation cost $1,245
to ensure easy maintenance and more efficient use of in plants and supplies, the annual savings brought a
water. See the tables on pages 19 to 31 for information total return on investment within three years. Therefore,
on mature height and spread of commonly used plants a water-wise landscape saves not only water but also
or ask your nurseryman or Extension agent about the money!
plant. Spacing plants far enough apart is extremely
important so that they can achieve their mature size Table 1. Surface area by water-use zone before and
without being crowded. Over-planting by placing plants after renovation
too close together not only increases your costs but Square Feet
also results in long-term maintenance problems and Zone* Before After
increases the potential for water stress. For additional Low 0 3,403
information, refer to Georgia Extension Service Leaflet Moderate 5,788 3,538
135, Spacing Plant Materials: Ground Covers; Leaflet High 3,662 2,509
134, Spacing Plant Material: Shrubs; and Leaflet 127, Total Irrigated Area 9,450 6,047
Spacing Plant Material: Trees. * Low = not irrigated; moderate = irrigated occasionally;
Select plants that have a size and form that con- high = irrigated regularly
form to their location without having to be sheared or
frequently pruned to keep them in bounds. Plants, like Table 2. Estimated annual water use and annual cost
people, grow in all shapes and sizes. If left unpruned, of water, sewage and landscape maintenance before
some plants will be tall and thin; others will stay short and after renovation
and spreading. Some will be irregular with open
branching; others will be compact with dense foliage. Before After Savings
Choose plants with the same shape and ultimate Water use (gallons) 81,437 51,723 29,714
size as the space you want to fill. For example, to plant Est. annual water cost $199.68 $133.56 $66.12
an area in front of low windows, 2 feet above the ground, Est. annual sewage cost $140.94 $94.54 $46.40
select spreading low-growing shrubs with an anticipated Est. annual maintenance $660.00 $423.00 $237.00
height of not more than 2 feet. Refer to pages 21 to 22 costs
for a suggested plant list. Avoid using too many kinds of Overall cost $1,000.62 $651.10 $349.52
plants, because the landscape will look like an arboretum
Additional examples of Xeriscape-type renovations
and will lack unity. For the typical home, three to five dif-
are shown on pages 32 to 39.
ferent shrubs, in addition to ground covers and trees, are
The alteration of an existing landscape to conserve
recommended for the basic plantings around the house.
water does not have to be as elaborate as that shown.
For more information on selecting plants for Xeriscape-
In many instances, it may be as simple as relocating a
type landscape, as well as a suggested plant list, see
few shrubs or flowering trees to more environmentally
“Appropriate Plant Selection” on page 9 and “Durable
suitable locations on the property or improving the
Plants for Xeriscape-type Landscapes,” pages 19 to 31. shape of plant beds to simplify irrigation. Considerable
savings can result by converting irrigated areas to
Renovation of an Existing Landscape ground covers or natural mulch areas. Simply changing
for Improved Water Conservation management practices and watering habits without
Figure 9 depicts before and after views of a typical making any physical changes in the landscape often
residence renovated for water conservation. can save large amounts of water. For each 1,000
The before view illustrates a rather dull landscape with square feet of landscaped area converted from an irri-
foundation shrubs ringing the house, a hedge along three gated to a nonirrigated area, you can save an estimated
sides and some native trees along the rear of the property. minimum of $60 per year on water and sewage costs.
6
9. BEFORE
AFTER
Figure 9. Before and after Xeriscape retrofit showing changes in water-use zones and view of backyard
7
10. STEP 2: SOIL ANALYSIS Research at the University of Georgia shows that
plants transplanted into a large planting hole establish
themselves more quickly and develop a significantly
Inspect Your Soil larger root system than those in a small hole no larger
A thorough analysis of both the physical and than the root ball. A large, extensive root mass
chemical characteristics of the soil is important when improves the plant’s ability to absorb moisture from the
developing a water-wise landscape. Georgia has a soil and helps the plant survive drought.
wide variety of soil types, ranging from well-drained Next, make certain the top of the root ball is level
coastal sands to poorly drained clays. Each soil has its with the soil surface, then backfill with the same soil
own unique structure and texture, drainage pattern, pH, removed from the hole. Do not add amendments to the
nutrient content and need for amendments and fertiliz- hole. Simply backfill with the native soil after removing
er. To complicate matters, an individual landscape may stones, sticks and other debris. Tamp the soil lightly to
have several different soil types, or the soil may consist eliminate air pockets. Water thoroughly and then add
of fill dirt brought onto the site. Soils are seldom per- organic mulch, such as pine straw or bark ships, to the
fect; most of them can be improved in some way to soil surface to conserve moisture.
ensure best plant growth. When planting a group of shrubs, cultivate the soil
throughout the area as deeply as possible. Cultivation
Soil Analysis Saves Guesswork changes the structure of the native soil and provides a
Before landscaping, take a sample of your soil to good environment for root growth.
your local county Extension office for testing. Your
county Extension agent will provide you with a recom- Improve the Structure of Poor Soils
mendation for lime and fertilizer based on the analysis. Certain native soils, like dense, poorly drained
clays, have such poor structure that plant growth suf-
Do Not Add Organic Matter to the Planting fers unless they are improved. Poorly drained soils can
Hole for Trees and Shrubs be improved in several ways. Sometimes deep cultiva-
For years we have added organic matter such as tion will break apart a hard layer of soil (hardpan) sev-
peat moss, animal manure or compost to the planting eral inches below the soil surface and improve
hole to enrich the soil, to conserve moisture and to drainage. Another option is to bring in additional soil to
improve plant growth. But recent research shows no raise the planting area 12 to 15 inches above the exist-
benefit from amending the planting hole. In fact, organ- ing grade. Some professional landscapers also incor-
ic matter added to individual planting holes in clay soils porate 3 to 6 inches of a coarse aggregate, such as
acts like a sponge in a bathtub, holding excess mois- granite sand, into poorly drained soils. A final option is
ture around plant roots after irrigation or rainfall. Wet, to install subsurface drainage pipe to carry excess
waterlogged soils that suffocate plant roots are a lead- water off the site after rain.
ing cause of plant death in Georgia. Even in well- On the other hand, soils that tend to dry out rapidly
drained soils, organic matter encourages the roots of and hold little moisture will benefit from organic matter
plants to stay within the hole instead of growing out to such as aged animal manure or compost, incorporated
explore the native soil. uniformly throughout the planting bed. This is partic-
When planting individual trees and shrubs, dig a ularly helpful when water-requiring plants, like annuals,
large planting hole, at least two times wider than the are to be grown. However, instead of adding the organ-
root ball of the plant. See figure 10. ic matter to the planting hole, apply 3 to 6 inches on
the soil surface and incorporate it into the soil.
Your goal in soil analysis is to create an ideal soil
environment for the expanding root system. An ideal soil
has good aeration and drainage, yet holds adequate
moisture and nutrients for optimum root growth.
Research at the University of Florida shows that the roots
of trees and shrubs grow outward approximately seven
times the diameter of the root ball during the first growing
season when provided with a good soil environment.
Unfortunately, no cookbook recipe exists for soil
improvement. How you treat the soil depends on the
characteristics of the native soil, the type of plants to
be grown and the time of year when planting.
Before planting, check the structure and texture of
the native soil by digging a hole 12 to 15 inches deep
and examining the soil horizon. Is it loose and granular
Figure 10. Diagram of a properly planted shrub. Proper or hard and compact? Fill the hole with water and
planting is the key to healthy root growth and drought watch how fast it drains. If water remains in the hole
tolerance of trees and shrubs. after 12 hours, the soil is poorly drained.
8
11. Plants prone to drought stress, like azalea, dogwood,
annuals and herbaceous perennials, prefer a moist, well-
drained soil; plants known to be drought tolerant, such as
crape myrtle and juniper, will grow well on very dry sites
once established. Likewise, soil prepared for summer
transplanting when dry periods are likely to occur should
have a greater water-holding capacity than soil prepared
for fall transplanting when rainfall is generally more regu-
lar and irrigation demand is low.
Water-absorbing polymers, commonly called
hydrogels, are popular new products. Refer to figure 11.
These man-made crystals, sold under various trade
names, absorb several hundred times their weight in
water and gradually release it to plant roots. One pound
of crystals applied to 100 square feet of bed area will
absorb 20 to 25 gallons of water, or about 50 times as Figure 12. Beds of drought-tolerant ground covers
much moisture as peat moss. They last from six months such as junipers are an excellent way of reducing the
to several years in the soil, depending on product. water requirement of the landscape.
Native plants are not necessarily the most drought
tolerant. Even though a plant may be native to the area, it
may not adapt to an adverse new environment (microcli-
mate). When forced to grow in a harsh new environment,
native plants can become a high-maintenance nightmare.
In addition to the adaptability of a plant to the site,
other important criteria to consider include:
1. Mature size and form. Will the plant remain in
scale with the rest of the landscape as it matures,
or will it likely overgrow the site and compete with
other plants for space, nutrients and water?
2. Growth rate. Slow-growing dwarf shrubs and
ground covers used around the base of the
Figure 11. Hydrogels, synthetic polymers that absorb
home require little routine pruning.
hundreds of times their weight in water and gradually
3. Texture. Is the leaf texture fine, medium or
release it to the plants, are among the popular new
coarse, and does it combine well with the
products on the market for water conservation. One
teaspoon absorbs a quart of water. adjacent plants?
4. Color. Is the flower or foliage color compatible
Research to date with hydrogels is limited and has with other plants or the background color of
provided conflicting results. However, preliminary stud- the building?
ies with hydrogels at the University of Georgia shows 5. Functional use. Is the plant suitable for the
them to enhance the growth of summer annuals in location and intended purpose; i.e. under low
nonirrigated soils. Another potential use for hydrogels windows, along the perimeter of the property
reported by professional landscapers is in container as screening hedge, or as a ground cover?
plants to extend the time between waterings. Select healthy, vigorous plants. Examine the root
system for well-developed roots throughout the root
STEP 3: APPROPRIATE ball and an abundance of small white roots (absorptive
roots) along the exterior of the root ball. Examine the
PLANT SELECTION leaves and stems for insects or diseases and avoid
plants that are weak or appear unhealthy.
Appropriate plant selection means selecting plants Pages 19 to 31 contain descriptive listings of
that not only are compatible with the design but also durable ornamental plants and turfgrasses for Georgia
are well suited to the planting site and local environ- landscapes. Please note that it is not an all-inclusive
ment. It involves selecting plants according to the soil list. Listing all the ornamental plants grown and sold in
type and light level of the site. Ideally, the plants you Georgia would be impossible. The suggested water-
select should be adaptable to local fluctuations in tem- use zones for each plant are based on observation,
perature and soil moisture. See figure 12. experience and best judgement of the authors and are
Drought tolerance is important in a Xeriscape-type certainly open for additions as research provides fur-
landscape. However, it should not be the only criteria ther data. Although many plants can grow in any of the
used to select plants. Junipers, for instance, are three water-use zones, for greatest water conservation,
extremely drought tolerant, but they cannot tolerate wet use them in zones that require the least amount of
soils or heavy shade. water whenever possible.
9
12. To best use the tables, first go to the section listing during periods of limited rainfall when growing turf in
the type of plant you desire, i.e. ground cover, vine, nonirrigated areas of the landscape.
ornamental grass, small shrub, medium shrub, large Maximum water conservation with turf is obtained
shrub, small tree, large tree, annual or perennial flow- through proper selection, establishment and mainte-
ers or turfgrass. Then select the plants having your nance. In addition to differing in appearance, turfgrass-
desired merits within each category, and group them es differ in their tolerance to environmental factors
into the appropriate water-use zone. such as shade, temperature, soil fertility, water use and
When selecting plants for a Xeriscape-type land- drought resistance. Table 3 shows water use and
scape, keep in mind this important fact: PLANTS drought resistance of some turfgrass species and vari-
DON’T SAVE WATER, PEOPLE DO! The plants we eties tested in Georgia. The water use is based on the
select do not save water; our ability to locate them in user’s adhering to recommended irrigation practices.
the landscape appropriately and to manage them prop- Drought resistance is important when growing turfgrass
erly determines their water needs. in nonirrigated areas. The turfgrasses listed would sur-
Match the water-use zones with the condition of the vive most droughts in Georgia.
planting site. For instance, place high-water-requiring
plants in areas of the landscape that stay moist and low- Table 3. Average water use and drought resistance of
water-requiring plants in areas that stay drier naturally. selected turfgrasses in Georgia.
Any ornamental plant or turfgrass presently on the Drought
market can be used in a Xeriscape-type landscape. In Common Name Water Use Resistance
fact, you may be surprised to learn just how many plants Tifway Bermuda Very Low Very High
can thrive without any supplemental water once they are Common Bermuda Very Low High
established. The key is to identify the water needs of the Raleigh St. Augustine Very Low Very High
plant you select, and then group it in the landscape with Rebel 11 tall fescue Very Low Medium
other plants having a similar need for water. By doing Centipedegrass Low Medium-high
this, supplemental irrigation can be applied most effi- Meyer Zoysia Low Low
ciently and only to those plants that require it. The result K 31 tall fescue Low Low-medium
is maximum water conservation in the landscape.
Practical turf areas mean using turfgrass for a specific
function in the landscape. A small “oasis” of turf near the
STEP 4: entrance to the home, a playing surface of durable turf in
PRACTICAL TURF AREAS recreational areas or a blanket of turf on a highly erodible
slope are all examples of “practical” turf areas. See figure
Turfgrass is one of the most versatile and function- 13. Also, design turf in practical shapes that can be effi-
al plants in the landscape. It provides one of the best ciently irrigated and maintained. Avoid sharp angles and
recreational surfaces for outdoor activities. From a long narrow strips that are difficult to mow and water.
water management standpoint, turf is recognized as Remember, the goal in developing a water-wise
one of the most effective plant covers to reduce runoff landscape is to reduce the need for supplemental irri-
and erosion while recharging the ground water, which gation, regardless of whether in turf or in ornamental
results in more efficient use of rainfall. areas of the landscape. As irrigated space decreases,
Turf has a tremendous mitigating effect on the water savings increase.
environment. For example, research documents that a For additional information on turfgrass selection and
turf area can be as much as 30°F cooler than a con- maintenance, see “Appropriate Maintenance” on page 16,
crete or asphalt surface and 10°F to 14°F cooler than “Turfgrasses” on page 31 and Cooperative Extension
bare soil. This cooling effect from the average lawn is Service Bulletin 733, Lawns in Georgia.
equal to more than eight tons of air conditioning; the
average home central-air unit produces three to four
tons. Turf also absorbs dust and other air pollutants
and produces oxygen.
However, in the typical landscape, turfgrass occu-
pies the largest area and, when managed incorrectly,
receives the largest amount of irrigation. You can real-
ize considerable water savings by irrigating only the turf
in high impact, highly visible areas of the landscape.
All turfgrasses recommended for Georgia can be
used in any water-use zone and can survive most
droughts without supplemental irrigation once they are
established. During drought periods, a healthy turfgrass
will wilt and turn brown, then regain its normal color
and growth when it receives adequate water. You must Figure 13. An area of well-maintained turfgrass is like
be willing to accept a loss of quality and appearance a welcome mat at this home.
10
13. STEP 5: ed area. This allows uniform watering along the edges
while avoiding wasteful overspray onto buildings,
EFFICIENT IRRIGATION paved areas and other adjacent areas.
Proper spacing of sprinklers is crucial in achieving
A water-wise landscape requires a minimal amount uniform water application. Sprinklers that do not overlap
of supplemental water from irrigation. When irrigation is adequately will waste water by applying too much water in
used, water is applied efficiently and effectively to some areas and not enough water in others. On the other
make every drop count. hand, spacing sprinklers closer than required increases
Just as we zone plants in the landscape according the cost of the system and wastes water. In general, spac-
to their different water needs, zone the irrigation sys- ing between sprinklers should be about 50 percent of the
tem so that plants with different water needs are irrigat- wetted diameter. For example, sprinklers with a wetted
ed separately. Water turfgrass, for instance, separately diameter of 80 feet should be spaced 40 feet apart.
from shrubs and flowers. Where part-circle sprinklers are used on the same
Using irrigation water efficiently also requires us to zone with full-circle sprinklers, the sprinklers should be
select the appropriate type of irrigation for the plants carefully selected to achieve a “matched precipitation
and for each area of the landscape. Trees and shrubs rate.” A half circle sprinkler will only water half as much
in the low water-use zone would need supplemental area as a full circle sprinkler; therefore, it should only
water only during establishment (first 8 to 10 weeks discharge half as much water. If a full-circle sprinkler
after transplanting); plants in moderate water-use discharges six gallons per minute, then a half-circle
zones require water only during periods of limited rain- sprinkler should deliver three gallons per minute and a
fall when they show signs of stress. For these plants, a quarter-circle sprinkler one and one-half gallons per
temporary system such as a soaker hose or hand minute. Most manufactures offer sprinklers with
watering may be all that is required. On the other hand, matched precipitation rate (MPR) nozzles.
high water-use zones require frequent watering and One other important aspect of proper design is pipe
may warrant a permanent system with automatic con- sizing. Selection of pipe sizes should be based on the
trols. Whenever possible, use highly efficient watering flow rate through the pipe. If pipes are too small, exces-
techniques, such as drip irrigation. sive pressure losses occur. This causes some sprinklers
to apply more water than others and results in nonuniform
Sprinkler Irrigation application and waste of water. Additional information on
Sprinkler irrigation may be as simple as a single pipe sizing and irrigation system design is available in
sprinkler attached to a garden hose, or it may be a Georgia Cooperative Extension Service Bulletin B 894,
complex system of underground pipes and pop-up Lawn and Garden Irrigation Design, as well as design
spray heads with automatic controls. A Xeriscape-type manuals available from the sprinkler manufacturers.
landscape uses sprinkler irrigation for watering turf
where water must be applied uniformly over the entire
area. For most other applications in the landscape drip
irrigation is a better choice.
Many types of sprinklers are available for use in
the landscape. Permanent systems with pop-up type
spray heads are most common. They are installed
underground and rise above the ground surface to
operate. Some are designed for use in turf (2 to 3 inch
pop-up height); others are designed for use in beds of
taller plants (6 to 12 inch pop-up height). Some sprin-
kler heads are designed for watering small irregularly
shaped areas. These typically have a radius of 15 feet
or less. Others, like rotary sprinkler heads, wet a radius
of 20 to 50 feet and are used to irrigate large areas.
Most sprinklers are available in either full-circle or part-
Figure 14. Use rain gauges to monitor the output of
circle models and most have an adjustable radius for
your sprinkler system.
watering irregular areas.
Proper Design Is Important Check the Application Rate of Your Sprinkler Systems
The installation of an efficient sprinkler system Application rate is the rate at which a sprinkler sys-
begins with good design. The system must be capable tem applies water to the soil surface, measured in inch-
of applying water uniformly over the desired area with es per hour (in./hr.). If application rates exceed the
minimal overspray into adjacent areas. intake capacity of the soil, then runoff occurs. Problems
Choosing the appropriate sprinkler for a given area with runoff are more likely to occur in clay soils, which
is important, but equally important is the location and have a low intake capacity.
spacing of sprinklers. It is usually desirable to place Rotary sprinklers usually have application rates of
part-circle sprinklers along the boundaries of the irrigat- 0.25 to 0.50 inches per hour and rarely cause runoff.
11
14. Spray heads, on the other hand, typically have applica- Most drip systems will use PVC pipe for main lines
tion rates between 1 and 2 inches per hour and may and polyethylene tubing for distribution lines. Poly-
cause run-off on heavy soils, especially where slopes ethylene tubing is flexible, easy to cut, and can be con-
are greater than 10 percent. If run-off occurs, turn the nected without glue or clamps. Install emitters by
system off for an hour or two to let the water soak in, punching a hole in the polyethylene tubing and snap-
and then apply the remainder of the water. ping the emitters into place.
Determine application rate of a sprinkler system by The drip system must have a main valve to turn it
placing three or four rain gauges at random on an irrigat- on and off. It may be an automatic electric valve con-
ed area for a predetermined length of time (usually one nected to a controller or a manual gate valve. You can
hour). See figure 14. By knowing the application rates of also connect the drip lines directly to an outside faucet.
your sprinkler system, you will know how long to operate However, when connecting the system directly to the
the system to apply a given amount of water and will faucet, use an automated timer to turn the system off
avoid wasting water. Average water level within the after a preset time. Otherwise, you may forget and
gauges is a measure of the output of the system (inches leave the system on for several days.
per hour). Repeat this procedure in each sprinkler zone, Two other necessary components for a drip system
particularly if different types of sprinklers are used on dif- are a filter and a pressure regulator. A drip system uses
ferent zones. For additional information on determining small passageways to control the rate of water applica-
sprinkler application rate see Georgia Extension Service tion, so even tiny particles suspended in the water could
Bulletin 894, Irrigation for Lawns and Gardens. cause clogging problems. To prevent clogging, use a
screen filter with a 150 to 200 mesh screen.
Adjust Sprinkler Heads as Needed
Figure 15 is a diagram of a typical component of a
Improper adjustment of sprinkler heads not only
drip irrigation system.
wastes water but also may damage buildings or cause
accidents if the water is allowed to spray onto build-
ings, public streets or sidewalks. Carefully adjust the
radius and arcs of part-circle sprinklers to prevent
undesirable overspray. Check the system several times
during the year to ensure proper adjustment.
Drip Irrigation
Drip irrigation, also called trickle or micro-irrigation,
applies water slowly and directly to the roots of plants
through small flexible pipes and flow control devices
called emitters. Drip irrigation uses 30 to 50 percent
less water than sprinkler irrigation and usually costs
less to install. Apply water directly to the root zone to
Figure 15. Typical controls required for drip irrigation.
minimize evaporative water loss and run-off.
These components are usually installed below ground
For maximum water-use efficiency, use drip irriga-
in a valve box.
tion on trees, shrubs and flowers in the high and mod-
erate water-use zones of the landscape. Several types
of drip irrigation systems can be adapted to suit a vari- Most drip systems are designed to operate at a
ety of applications, from watering individual trees and pressure of about 20 psi, (pounds per square inch).
shrubs to beds of annuals, herbaceous perennials or Household water pressure typically ranges from 40 to
ground covers. 100 psi. A pressure regulator installed immediately after
the filter in the main line will reduce the pressure in the
Components of a Drip System line and ensure efficient operation of the system.
In a drip system, water is distributed to the plants
through small, flexible plastic pipes (3/8 to 3/4 inch in diam- Which Drip System Is Best?
eter) and emitters or through perforated or porous pipe. Because so many different types of drip irrigation
Emitters may be purchased separately from the components exist, trying to choose the best system for
tubing and placed in the line wherever watering is a particular application is often confusing. The best
desired. Another option is to purchase drip tubing with advice is to keep it as simple as possible and try to wet
emitters already installed at the factory, usually spaced only those areas where the water can be taken up by
12 to 24 inches apart. Most emitters will discharge the roots of the desired plants.
water at a rate of 2, 1 or 2 gallons per hour at a pres- For trees and shrubs, using a system in which you
sure of about 20 pounds per square inch. can insert emitters wherever water is needed is gener-
Perforated or porous pipe discharges water along its ally best. The number of emitters per plant and flow
entire length to wet a continuous strip. By spacing the rate (gallons per hour) per emitter depend on the size
pipe 12 to 18 inches apart, wetting a solid area is possi- and type of plant. Generally, the larger the plant, the
ble. It is a good system for closely spaced plantings of more water it requires. The following is an example of
annuals, herbaceous perennials or groundcovers. how emitters might be installed based on plant size:
12
15. Plant Height (ft.) Emitters per Plant dew develops (9 p.m.) and before it dries in the morn-
<2 one, ½ gallon per hour ing (9 a.m.) does not increase disease problems.
2-4 one, 1 gallon per hour Drip irrigation systems can be operated any time of
4-6 two, 1 gallon per hour day because evaporative water loss is not a problem,
6-7 three, 1 gallon per hour and the foliage stays dry.
7-8 four, 1 gallon per hour An Automatic Controller Helps Save Water
two, 2 gallons per hour An automatic controller attached to the irrigation
system turns the system on and off and controls the
During very dry weather, this system would need to water flow through the various zones according to a
run about three times per week for four hours to supply preset time clock. See figure 16. It allows you to set
the optimum water needs of the plants. Keep in mind the length of time each zone operates as well as the
that some species require more water than others. days of the week and time of day the system operates.
Consider this when installing emitters.
For watering annuals, perennials and ground cov-
ers, it is usually necessary to irrigate a solid area. This
can be done using emitter lines with emitters spaced
every 12 to 18 inches. By placing emitter lines 12 to 18
inches apart, a uniform wetting pattern can be
achieved. Perforated or porous pipe spaced every 12
to 18 inches apart can also be used. In sandy soils, the
lines will need to be closer together than in tighter
soils. In annual flowerbeds, the drip lines can be laid
aside during bed preparation and replaced afterwards.
A similar method of watering uses small sprinkler
heads called microsprinklers, instead of emitters. All
other components are identical to drip irrigation, includ-
ing the polyethylene distribution lines. Microsprinklers
spray an area 3 to 12 feet wide and are used for trees Figure 16. Using an automatic controller can save
and shrubs or beds requiring complete coverage. water and labor.
Microsprinklers may be prone to vandalism and are not
quite as efficient as emitters, but they do provide an However, an automatic controller does not relieve
economical method of achieving uniform watering. you of the need to closely monitor its operation. Con-
In landscape applications, drip irrigation tubing is trollers should be reprogrammed frequently during the
usually installed on top of the ground and concealed growing season because water needs change from
beneath mulch. This makes the system easy to install week to week.
and service. However, if vandalism is likely, the tubing A rainfall sensor attached to the controller detects
can also be installed 4 to 6 inches beneath the soil sur- rainfall and prevents the irrigation system from operat-
face with small microtubing (1/8 to 1/4 inch) protruding to ing if significant rainfall has occurred. Another type of
the surface. Running the microtubes above ground will sensor measures soil moisture and overrides the sys-
allow for easy inspection and will prevent dirt from tem when soil moisture is adequate. Sensors are espe-
siphoning back into the emitters and clogging the system. cially useful if the system cannot be monitored and
adjusted regularly.
Guidelines for Irrigating the Landscape Many different types of controllers are on the mar-
Establish Irrigation Objectives ket. Make sure you get one with the features you need.
In a Xeriscape-type landscape, your goal is to mini- When managed properly, an automatic controller can
mize the amount of supplemental water applied to the pay for itself in reduced water usage, cost and labor.
landscape. Therefore, routine irrigation is necessary Hand Watering
only in the high water-use zones of the landscape. Hand watering is not just for newly planted orna-
Occasional hand watering or a portable irrigation sys- mental plants. It is also an effective and efficient way of
tem, such as porous pipe, would be used as needed in applying water to selected plants that show signs of
the moderate water-use zones, while established stress during dry periods. The direct application of
plants in low water-use zones would receive only natur- water to the base of the plant, provided it is applied
al rainfall and no supplemental irrigation water. slowly enough to be absorbed by the soil, uses less
Operate Sprinklers Between 9 p.m. and 9 a.m. water and is more efficient than sprinkler irrigation.
Time of application affects water-use efficiency. To avoid runoff when using the hand-held hose, use
The best time to irrigate with sprinklers is between 9 a nozzle that divides the spray into rain-size droplets.
p.m. and 9 a.m. During this time, less wind and lower Some nozzles have built-in spray pattern adjustments.
temperatures generally occur; therefore, less water is When watering by hand, apply about 5 gallons of
lost to evaporation. Irrigating during the evening after water per 10 square feet, which is approximately the
13
16. amount of water delivered by a 5/8 inch garden hose Irrigating Trees and Shrubs
operating one minute at medium pressure. Watering small Woody ornamental trees and shrubs have a deeper,
shrubs (less than 4 feet in height) for one minute with the more extensive root systems than turfgrasses or herba-
hand-held hose should suffice. Larger shrubs (4 feet and ceous ornamental plants. The root system of a mature
up) will require slightly more water. Increase the watering tree, for instance, extends two to three times the canopy
time by 15 seconds for each foot of height exceeding four spread and may go down several feet into the soil. Woody
feet. For large trees, apply about 6 or 7 gallons for each plants, therefore, can extract moisture from the soil even
10 square feet of canopy area. For best results, check the when the soil surface appears bone dry and can survive
output of your faucet by determining the number of sec- long dry periods without supplemental irrigation.
onds to fill a one-gallon jug and then estimating output per Use drip irrigation on trees and shrubs in the high
60 seconds. If runoff occurs before you have applied the water-use zones of the landscape. Locate the emitters
correct amount of water, move on to another spot and near the drip line of plants where the concentration of
come back after the water has soaked in. absorbing roots is the highest. During extended dry
Irrigating Turfgrass periods, operate the system two to three times per
Turfgrasses used in Georgia can survive seasonal week. Run the system long enough to thoroughly wet
dry periods without irrigation and therefore can be used the soil 18 to 24 inches deep.
in any water-use zone. In moderate water-use zones, a Regular and thorough watering of newly planted
turfgrass would be irrigated only when it shows signs of trees and shrubs will encourage good root establishment
moisture stress. Turf under water stress will appear a and greater drought resistance. See page 17 for sugges-
dull bluish green color, the leaf blades will roll inward, tions on survival watering during drought or restrictions.
and footprints will remain on the grass after walking Irrigating Herbaceous Ornamentals
over an area. Irrigating turf in the moderate water-use (Annuals and Perennials)
zones with a portable lawn sprinkler within 24 to 48 Herbaceous ornamentals vary widely in their tolerance
hours of these signs will generally prevent serious loss to drought. Some will perform adequately with a minimum
of turf vigor while maximizing water-use efficiency. of supplemental water while others require close attention
Under optimum growing conditions (high water-use to soil moisture. Irrigation can be provided most efficiently if
zone), turfgrasses use 1 to 12 inches of water per the plants within a bed have similar water needs.
week during hot dry weather. Dividing this amount into Herbaceous ornamentals generally have a shallower root
two applications per week, applying 2 to 3/4 inch each system than woody ornamentals and are among the first
time, usually works best. Never apply more than one plants in the landscape to show water stress during dry
inch at a time because this will likely result in runoff or periods. Water these plants once or twice a week and use
deep percolation below the root zone. Early or late in drip irrigation whenever possible. If you can not water
the season when temperatures are cooler, irrigating because of restrictions, remember that these plants are
only once per week is usually adequate. less costly to replace than trees and shrubs.
Never water grass daily except during establish-
ment. Daily irrigation with small amounts encourages a
shallow root system and reduced drought tolerance, as STEP 6: USE OF MULCHES
shown in figure 17. Because roots generally grow where Mulching is one of the most beneficial landscape
the soil is moist, a shallow root system also prevents practices. Mulches conserve moisture by preventing
efficient uptake of plant nutrients. Shallow, frequent irri- evaporative water loss from the soil surface and reduc-
gation increases evaporative water loss from the soil. ing the need for supplemental irrigation during periods
of limited rainfall. By maintaining an even moisture sup-
ply in the soil, mulches prevent fluctuations in soil
moisture that can damage roots. See figure 18.
Figure 17. The healthy, deep-rooted grass on the left
results from proper irrigation. The weak, shallow-rooted
grass on the right results from light frequent irrigation. Figure 18. Moisture level of mulched vs. bare soil
14
17. Mulches also prevent crusting of the soil surface help conserve the moisture remaining in the soil.
and allow water to penetrate readily to plant roots. Placing newspapers under organic mulches not
They insulate the roots of plants from summer heat and only improves water conservation in the soil but also is
winter cold and help control weeds that compete with an excellent way to recycle. Place them on the soil sur-
plants for moisture. By serving as a barrier between the face under organic mulch at planting time. They may
plant and soil, mulches help discourage soilborne dis- also be used on established ornamentals by carefully
eases that stress plants and cause them to have a removing the organic mulch from around the plants,
higher demand for water. placing the newspapers two sheets thick on the soil
Islands of unplanted organic mulch designed to surface and reapplying the mulch. Be sure to wet the
blend with the landscape are an economical way to retro- newspapers thoroughly immediately after application;
fit an existing landscape to make it more water efficient otherwise, they may pull moisture from the soil.
while reducing maintenance requirements. See figure 19.
Table 4. Advantages and disadvantages of commonly
used mulches
Mulch Advantages Disadvantages
Pine Straw An excellent mulch for Flammable when
water conservation extremely dry. Fades to
a dul gray-brown color
with age. Decomposes
rather quickly and
requires annual top-
dressing with additional
pine straw.
Pine Bark Mini-nuggets conserve None
moisture better than
large nuggets. They
also stay seated better
on the landscape than
Figure 19. Islands of natural organic mulch that blend large nuggets.
with the landscape are an economical way of con- Shredded/Chipped Provides a durable, None
serving water while reducing maintenance. Hardwood Bark long-lasting mulch
Fall Leaves An overlooked and Not as neat or uni-
readily available form in appearance
Aside from occasional weed control and topdress- mulch. Shredded as pine straw and
ing with additional mulch, unplanted mulched areas leaves stay seated pine bark
require no water and little routine maintenance. better on the land-
Pine straw, pine-bark, mini-nuggets and shredded scape and conserve
moisture better than
hardwood mulch or chips are some of the best mulches unshredded leaves.
for a water-wise landscape. These fine-textured
Grass Clippings None Decompose quickly,
mulches hold moisture in the soil better than coarse- mat down and mold.
textured mulches like large-nugget pine bark. They also Not recommended.
are nonmatting and allow water, nutrients and oxygen Compost them instead.
to freely penetrate to plant roots. Pecan Hulls An acceptable and Rough looking. Mold
Inorganic mulches, on the other hand, such as rock, economical mulch with age. Attract
where available wildlife when fresh.
gravel and marble, absorb and reradiate heat from the sun
and increase water loss from plants and soil. Table 4 com- Gravel, Marble Long lasting Absorb and reradiate
Chips, Volcanic heat. Unnatural in
pares several commonly used mulches on the market. appearance. Not rec-
Rock
Apply approximately 3 inches of mulch under orna- ommended.
mental plants in the landscape. Avoid applying too much Newspaper Placed two sheets When placed too
mulch because it encourages shallow roots, which are thick under organic thick (more than two
easily damaged by excessive cold, heat or drought. mulch, newspaper layers), it can serve
Where possible, extend the mulched area two to helps conserve mois- as a barrier to water
ture while allowing and nutrients.
three times the canopy spread of ornamental trees and water and nutrients to
shrubs. Research shows that the roots of ornamental penetrate.
plants grow far beyond the canopy spread, so mulching Landscape Fabric Allows nutrients and Aggravating to install.
as large an area as practical is important. water to penetrate to Does not prevent
Once mulch is in place, use your hand to pull it plant roots. Prevents nutsedge and other
back 2 to 3 inches away from the trunk of trees and most weeds. persistent weeds.
Must be covered by
shrubs. Keeping mulch away from the trunk will help an organic mulch.
prevent wood rotting diseases. Plastic Film None Prevents oxygen, nutri-
During periods of limited rainfall, make certain suffi- ents and water from
cient mulch is maintained beneath plants. If watering reaching plant roots.
restrictions prevent you from irrigating, mulches will Not recommended.
15
18. STEP 7: APPROPRIATE Avoid Shearing Plants
Just like nitrogen fertilizer, shearing promotes
MAINTENANCE water-demanding new growth on plants. When pruning
is required, use hand shears or loppers to thin branch-
By following the six previous steps toward water es and twigs to a side branch or bud. Thinning results
conservation in the landscape, you will have a beautiful in a more open, natural canopy and is less stressful to
landscape that not only saves water and money but the plant than shearing. See figure 20.
also requires minimal maintenance.
The objective of Xeriscape maintenance is to
discourage water-demanding new growth on plants. In
other words, keep plants healthy, but do not encourage
growth at all times. Depending on your current level of
maintenance, this may require you to fertilize less often
with less fertilizer, to prune only when necessary and
lightly when essential and, of course, to irrigate less.
Remember, a Xeriscape-type landscape is a low-main-
tenance landscape. By working smarter, not harder, in
the landscape, you’ll save time, energy and water with-
out sacrificing the beauty of the environment.
Fertilize Less and Use Slow-release Fertilizers
When purchasing a fertilizer, look closely at its con- Figure 20. Thinning (right) is better than shearing (left).
tents. Nitrogen, the first number in the analysis, is the
element that promotes new growth. Purchase a fertiliz-
er having nitrogen in a slow-release form, such as
Proper Mowing Saves Water
sulfur-coated urea, urea formaldehyde, IBDU (isobuty-
Proper mowing practices are of particular impor-
lene-diurea), or methylene urea. Some new products
tance in Xeriscape-type landscapes. Mow at the rec-
on the market feed plants for an entire growing season
ommended height (Table 5), and mow often enough so
with one application. Slow-release type fertilizers gen-
that no more than one-third of the leaf tissue is
erally cost more than soluble all-purpose garden fertil-
removed at each mowing. For example, if tall fescue is
izers, such as 8-8-8 or 10-10-10, but they last longer
to be maintained at a height of 2 inches, then it would
by releasing nutrients gradually. Also, they do not leach
be cut when it reaches 3 inches. Research shows that
from the soil or wash away in run-off as readily as all-
raising the mower blade during dry weather and cutting
purpose fertilizers.
the grass higher encourages deeper rooting, increases
Always check the application rate on the label. The
turf survival during drought and reduces water demand.
label usually suggests an application rate for optimum
Mow turf in shaded areas higher than turf in full
growth. This application rate is ideal for newly planted
sun. Avoid scalping and stressing the grass and make
ornamental plants and turfgrasses to encourage healthy
certain the mower blade is sharp at all time.
new growth and plant establishment. However, once
plants are established, the recommended application
rate of fertilizer can be reduced without sacrificing quali- Table 5. Mowing heights for turfgrasses in Georgia
ty or appearance. This reduction in application rate is Turfgrass Mowing Height (Inches)
particularly important before or during dry periods. Centipede 1 to 1.5
Leaving grass clippings on turfgrass at each mow- Common Bermuda 1 to 2
ing, a process called grasscycling, supplies the grass Hybrid Bermuda 0.5 to 1.5
with recycled nutrients and reduces the need for supple- Tall fescue 2 to 3
mental fertilizer. Grasscycling does not promote thatch, a St. Augustine 2 to 3
spongy condition of the turf. Thatch results from a build- Zoysia 0.5 to 1.5
up of grass stems, shoots and roots, not clippings. As
much as one-third of the nutrients applied to your lawn
can be recycled back to the grass through grasscycling. Aerating Turfgrass Improves Water Movement
Aeration or coring of turf areas is sometimes
Soil Testing Saves Guesswork required to relieve soil compaction and to increase air
Soil pH, a measure of a soil’s acidity or alkalinity, and water movement into the soil. It is particularly helpful
affects nutrient availability and uptake. Take a separate on slopes where water run-off is possible and in areas of
soil sample from your turf and ornamental areas every heavy foot traffic where compaction has occurred. Aera-
two to three years to monitor pH and nutrient levels to tion is best accomplished with a power aerator that has
determine if you need to add lime or otherwise adjust hollow tines to remove small cores of soil. Many rental
the chemical balance of the soil. Soil testing is available stores have this type of equipment available. Aeration is
through you local Cooperative Extension Service office. best during periods of active plant growth and when the
16
19. soil is moist enough to allow deep penetration of the
tines. Generally, aeration is used to correct soil problems
SUMMARY
and is not done on a routine basis. In the future we are not going to have as much
For additional information on turfgrass mainte- water for landscape use as we had in the past. As
nance, see Georgia Extension Service Bulletin 733, urban areas continue to grow and develop, water short-
Lawns in Georgia. ages are likely to be a recurring problem because of
population pressure on available water supply.
Other Water-saving Maintenance Practices By implementing the Xeriscape fundamentals
Don’t Let Weeds Compete With Plants for Water described in this publication, you can reduce your out-
Scout the landscape regularly and don’t let weeds door water use by as much as 50 percent without sac-
take over. Hand weeding, chemical herbicides and rificing the quality or beauty of the home environment.
mulches will help keep weeds in check. Let’s review each of the fundamentals once more:
Scout for Pests Before You Spray 1. Planning and Design: Start with an accurate
As you scout for weeds, also scout for insect and plan of the site, identify site problems and
disease pests. Control pests when they begin affecting potentials, and develop a list of needs and
the appearance and overall health of a plant. Target wants to be incorporated in the new plan. As
your control measures to the affected plants and avoid your plan begins to take form, divide the land-
spraying the entire landscape if the pest problem is scape into water-use zones. Incorporate shade
confined only to a small area. where possible, and develop your plan using
Make Every Drop Count appropriate plants.
Where irrigation systems are used, check nozzles 2. Soil Analysis: Evaluate the planting soil,
and emitters regularly to see if they are operating effi- including its structure, texture, water-holding
ciently and are delivering the right amount of water and capacity and drainage. Let the physical and
in the right locations. chemical characteristics of the existing soil be
your guide in determining the type of soil
Let Your Plants Tell You When They Need Water
improvement needed.
Learn to identify the symptoms shown by plants
3. Appropriate Plant Selection: Select plants
under water stress. Shrubs under moisture stress will
appropriate to the site and the imposed stress-
turn a gray-green color and wilt. Trees will show prema-
es of the environment. Any of our Southern
ture fall color and shed leaves. Turfgrass will turn a dull
ornamental plants presently on the market are
gray-green color, and the blades will wilt and roll inward.
good candidates for a water-wise landscape as
Survival Watering During Drought or Watering long as they are adapted to the site and zoned
Restrictions in the landscape according to their water need.
During drought or watering restrictions, consider the 4. Practical Turf Areas: Use turf for a function or
replacement cost of the plants in the landscape and do aesthetic benefit, such as in a recreational
what you can to save the most valuable plants. Annual area, an erodible slope or a welcome mat to
flowers can be replaced more readily than trees and the home. Select a turfgrass that is adapted to
shrubs. If you can not water, cut back annual flowers and the site and has good drought resistance.
mulch them heavily to help them survive a drought. 5. Efficient Irrigation: When irrigation is
Turfgrass and herbaceous perennials will go into a dor- required, make every drop count by watering
mant state when under moisture stress. During watering efficiently to prevent run-off or evaporative loss.
restrictions, selectively hand water shrubs and trees Let your plants tell you when they need water,
showing drought stress. Although trees have an exten- and avoid watering according to a set schedule
sive “bank account” of roots to absorb water during dry or habit. Hand watering individual plants and
periods, prolonged drought can severely stress and dam- drip irrigation on ornamentals requires 30 per-
age a large portion of their surface roots. A thorough cent to 50 percent less water than sprinkler irri-
watering of three small areas (60 gallons/100 square feet gation. Water between 9 p.m. and 9 a.m. to
near the drip-line) each two weeks in clay soils and once avoid evaporative loss of water.
a week in sandy soils using the hand-held hose will mini- 6. Use of Mulches: Use fine-textured organic,
mize tree damage during an extended dry period. nonmatting mulches when possible. Fall
If restrictions do not allow you to water outdoors leaves, pine straw, pine bark, mini-nuggets and
at all, prune back trees and shrubs by one-third to one- shredded hardwood bark are excellent choices.
half when they become severely wilted and begin shed- Mulch as large an area as possible under tree
ding leaves. This will reduce water demand on the roots shrubs. Islands of unplanted mulch require no
and increase their chances of survival during drought. water and little routine maintenance.
In some Georgia counties, the use of gray 7. Appropriate Maintenance: Keep plants healthy,
water (i.e., bath water or dish water) is permissible out- but do not encourage water-demanding new
doors. Check with your local health department regard- growth. Once plants are established, reduce the
ing the legality of using gray water outdoors. amount of nitrogen applied as well as the appli-
17
20. cation rate and frequency of application. Avoid ing habits and learning how to water, when to water,
plant stress by mowing properly, by thinning the most efficient ways to water and the water needs of
shrubs instead of shearing, and by controlling our Southern ornamental plants.
weeds and pests before they affect plant health. By putting the Xeriscape fundamentals into practice in
your landscape, you will become a good steward of the
Remember, the landscape alone does not save environment and you will be doing your part to ensure
water; it is up to us to save water. Considerable water your family and future generations, the same quality of life
savings can be realized simply by breaking bad water- we all have grown to enjoy and appreciate in Georgia.
GEORGIA HARDINESS ZONES
Range of average annual minimum
temperatures for each zone.
Zone Range in degrees
6b -5 to 0
7a 0 to 5
7b 5 to 10
8a 10 to 15
8b 15 to 20
18
21. DURABLE PLANTS FOR XERISCAPE-TYPE LANDSCAPES
See pages 9 and 10 for information on how to use these tables.
Vines
Water' Georgia
Botanical Name Use Hardiness Flower Color/ Growth
and Common Name Zone Zone Time of Bloom Rate Group Exposure
Antigonon leptopus 1, 2, 3 8 Reddish Pink/ Fast Deciduous Sun
Coral Vine Summer
Campsis radicans 1, 2, 3 6b to 8 Orange/ Fast Deciduous Sun/Shade
Trumpet Vine Summer
Clematis hybrids 1, 2 6b to 8 Purple, Pink, Medium Deciduous Sun/
Flowered Clematis White/Spring Semi-shade
Fatshedera lizei 1, 2 7 to 8 Not Showy Medium Evergreen Shade/
Fatshedera Semi-shade
Ficus pumila 1, 2 7b to 8 Not Showy Slow Evergreen Sun/Shade
Climbing Fig
Gelsemium sempervirens* 1, 2, 3 6b to 8 Yellow/Spring Medium Evergreen Sun/
Carolina Jessamine Semi-shade
Lonicera x heckrottii 1, 2, 3 6b to 8 Pink/Spring Fast Evergreen Sun/
Goldflame Honeysuckle Semi-shade
Lonicera sempervirens* 1, 2, 3 7b to 8 Orange-Red- Fast Evergreen Sun/
Trumpet Honeysuckle Yellow/Spring Semi-shade
Parthenocissus quinquefolia 1, 2, 3 6b to 8 Greenish White/ Fast Deciduous Sun to Shade
Virginia Creeper Summer
Not Showy
Parthenocissus tricuspidata 1, 2, 3 7b to 8 Not Showy Fast Deciduous Sun/Shade
Japanese Creeper
Rosa banksiae 1, 2, 3 6b to 8 White/Spring Fast Semi-evergreen Sun
Banks Rose
Rosa species 1, 2 6b to 8 Many Colors/ Fast Deciduous Sun/
Climbing Roses Spring Semi-shade
Trachelospermum jasminoides 1, 2, 3 7 to 8 White/Summer Medium Evergreen Sun
Star or Confederate Jasmine
* Denotes native Georgia plant
' Water Use Zones: 1 = regular irrigation; 2 = moderate, occasional irrigation; 3 = low, no irrigation (natural rainfall)
19