This document provides information about the Georgia commercial driver's license, including the knowledge and skills tests required to obtain a CDL. It discusses the various license classes and endorsements, outlines the sections of the manual to study for each, and reviews driver disqualifications. Key points include:
- You must pass knowledge and skills tests to get a CDL based on your vehicle and intended transportation of passengers or cargo.
- Certain offenses can lead to license suspension or revocation, such as driving under the influence or railroad crossing violations.
- The manual helps determine your testing needs and prepares you to operate commercial vehicles safely according to Georgia standards.
1. 2009
GEORGIA
COMMERCIAL
DRIVER’S MANUAL
Revised Nov 08
2. This material is based upon work supported by the Federal Motor Carrier Safety
Administration under Cooperative Agreement No. DTFH61-97-X-00017. Any
opinions, findings, conclusions or recommendations expressed in this publication
are those of the Author(s) and do not necessarily reflect the view of the Federal
Motor Carrier Safety Administration.
This manual has been modified to comply with the standards, rules and laws set
by the state of Georgia.
3. Table Of Contents
Introduction ............................................................................................................................. 1-1
Driving Safely ....................................................................................................................... 2-1
Transporting Cargo Safely ...................................................................................... 3-1
Transporting Passengers Safely ....................................................................... 4-1
Air Brakes ................................................................................................................................. 5-1
Combination Vehicles .................................................................................................. 6-1
Doubles and Triples ....................................................................................................... 7-1
Tank Vehicles ....................................................................................................................... 8-1
Hazardous Materials ..................................................................................................... 9-1
School Bus ............................................................................................................................ 10-1
Pre-Trip Vehicle Inspection .................................................................................. 11-1
Basic Vehicle Control Skills Test .................................................................... 12-1
On-Road Driving .............................................................................................................. 13-1
4. 2009 Commercial Driver’s License Manual
Do You Need a CDL?
Section 1 Does the vehicle or
INTRODUCTION combination of vehicles
have a manufacturer’s
No
weight rating (GVWR)
This Section Covers over 26,000 pounds?
Commercial Driver License Tests
Driver Disqualifications Yes
Other Safety Rules Is the
vehicle a
There is a federal requirement that each state have combination
Yes
You
vehicle need a
minimum standards for the licensing of commercial towing a unit Class A
drivers. over 10,000 CDL.
pounds
This manual provides driver license testing information GVWR?
for drivers who wish to have a commercial driver
license (CDL). This manual does NOT provide No
information on all the federal and state requirements
needed before you can drive a commercial motor
vehicle (CMV). You may have to contact your state Does the
Yes
You
single need a
driver licensing authority for additional information. vehicle have Class B
a GVWR CDL.
You must have a CDL to operate: over 26,000
pounds?
Any single vehicle with a gross vehicle weight rating
(GVWR) of 26,001 pounds or more. No
A combination vehicle with a gross combination weight
Is the
rating of 26,001 or more pounds, If the trailer(s) has a vehicle You
GVWR of 10,001 or more pounds. designed to
Yes
need a
A vehicle designed to transport 16 or more passengers carry 16 or Class C
(including the driver). more people CDL.
(including
the driver)?
Any size vehicle which requires hazardous materials No
placards or is carrying material listed as a select agent
or toxin in 42 CFR 73. Federal regulations through the No
Department of Homeland Security require a
background check and fingerprinting for the Does the You Yes
Hazardous Materials endorsement. The background vehicle
No
need a
require Class C
check can take up to six weeks. Contact the hazardous CDL.
Transportation Security Administration (TSA) at material
www.hazprints.com or your local department of driver placards or
licensing for more information. transport a
select agent
or toxin?
To get a CDL, you must pass knowledge and skills No
tests. You must take and pass the knowledge tests
prior to scheduling the skills test. This manual will help
you pass the tests. This manual is not a substitute for You DO NOT
a truck driver training class or program. Formal training need a CDL.
is the most reliable way to learn the many special skills
required for safely driving a large commercial vehicle NOTE: A bus may be Class A, B, or C depending on whether the
GVWR is over 26,001 pounds or is a combination vehicle.
and becoming a professional driver in the trucking
industry.
Figure 1.1
Figure 1.1 helps you determine if you need a CDL.
Section 1 - Introduction Page 1-1
5. 2009 Commercial Driver’s License Manual
1.1 – Commercial Driver License Tests requisite to the endorsement(s) being applied for. To
obtain a Passenger (P) or School Bus (S)
1.1.1 – Knowledge Tests endorsement, the driver must pass both CDL
knowledge and skills tests.
Each person applying for a Class P commercial or
noncommercial instruction permit for Class A, B, C, or If you do not have the license class required for an
M driver’s license shall pay the applicable license fee endorsement but are seeking that class while also
prior to attempting the knowledge test for the seeking the endorsement, the endorsement is only
instruction permit sought. If said person fails to granted if the knowledge test for the endorsement is
achieve a passing score on the knowledge test, the passed and all other requirements for the license class
license fee paid shall be considered a testing fee and also are met.
retained by the department. Any person failing to
achieve a passing score on the knowledge test for an If you fail an endorsement test, but have otherwise
instructional permit shall pay the applicable license fee passed the knowledge tests for the license class, you
on each subsequent attempt until successful, at which can still take the applicable skills tests. If you pass the
time the fee shall be his or her license fee. skills tests, you should be given the appropriate
license, but without the endorsement. You can then
You will have to take one or more knowledge tests, retake the endorsement test later without further skills
depending on what class of license and what testing except for obtaining a P or S endorsement (P
endorsements you need. To qualify for a license class, and S endorsements require a skills test be performed
a person must obtain a passing score on all in a bus).
knowledge tests required for that class. The CDL
knowledge tests are all multiple choice and include: Upon request the examiner will provide you with your
score for each knowledge test taken. All test material
The general knowledge test, taken by all applicants. is derived from the CDL Drivers Manual.
The passenger transport test, taken by all bus driver
applicants. The passenger transport skills test must After you have passed the knowledge test(s) for a
be taken and passed by all applicants in order to license class, you then must pass the skill tests. No
obtain this endorsement. class of CDL, or CDL upgrade is granted solely on the
The air brakes test, which you must take if your vehicle basis of passing the knowledge tests. If a driver fails
has air brakes, including air over hydraulic brakes. one or more of the knowledge tests required for a
The combination vehicles test, which is required if you license class, you must retake and pass the failed
want to drive combination vehicles. test(s) before taking the skills tests.
The hazardous materials test, required if you want to
haul hazardous materials or waste in amounts that Retest waiting period:
st
require placarding or any quantity of a material listed 1nd failure – one day
as a select agent or toxin in 42 CFR 73. In order to 2rd failure – one week
obtain this endorsement you are also required to pass 3th failure – 30 days
a Transportation Security Administration (TSA) 4 failure – must reapply (submit a new application
background check (go to www.hazprints.com for and pay new application fee) – and begin testing
additional information). phase again
The tanker test, required if you want to haul a liquid or
liquid gas in a permanently mounted cargo tank rated 1.1.2 – Skills Tests
at 119 gallons or more or a portable tank rated at
1,000 gallons or more. Each person applying for a Class A, B, or C
The doubles/triples test, required if you want to pull commercial driver’s license shall pay the applicable
double or triple trailers. license fee at the time that he or she schedules his or
The School Bus test, required if you want to drive a her appointment for said skills test. If said person fails
school bus. The school bus skills test must be taken to appear for his or her scheduled skills test
and passed by all applicants in order to obtain this appointment the license fee paid shall be considered a
endorsement. testing fee and retained by the department. All fees
retained by the department pursuant to this Code
The passing score for all knowledge tests is 80%. section shall be remitted to the general fund. A
customer may take the test two times without paying
With the exception of adding the Passenger (P) another fee (initial test and one retest).
endorsement or the School Bus (S) endorsement, a
driver who already has the required license class may If you pass the required knowledge test(s), you can
add the endorsement(s) after passing written tests take the CDL skills tests. There are three types of
Section 1 - Introduction Page 1-2
6. 2009 Commercial Driver’s License Manual
general skills that will be tested: pre-trip inspection, intersections, railroad crossings, curves, up and down
basic vehicle control, and on-road driving. You must grades, single or multi-lane roads, streets, or
take these tests in the type of vehicle for which you highways. The examiner will tell you where to drive.
wish to be licensed.
Figure 1.2 details which sections of this manual you
If you fail any part of the skills tests you can apply to should study for each particular class of license and
reschedule the retest as follows: for each endorsement.
Retest waiting period:
1st failure – one day What Sections Should You Study?
nd
2 failure – one week
rd
3 failure – 30 days LICENSE
4th failure – must reapply (submit a new application ENDORSEMENT
TYPE
and pay new application fee) – and begin testing
Class A
Class B
Class C
Materials
Hazardous
Double / Triple
Tank Vehicles
Passenger
School Bus
phase again
The following restrictions will become effective
January 2009:
♦If an applicant performs the skills test in a vehicle
equipped with an automatic transmission, that person
is restricted from operating a CMV equipped with a
Sections to Study
manual transmission. 1 X X X
♦Tractor-trailer - If an applicant performs the skills test
in a combination vehicle for a Group A CDL with the 2 X X X
power unit and towed unit connected with a pintle hook
or other non-fifth wheel connection, that person is 3 X X X X X X X
restricted from operating a tractor-trailer combination
connected by a fifth wheel that requires a Group A 4 X X X X
CDL.
♦If an applicant performs the skills test in a passenger 5* X X X X X X
vehicle requiring a Group B CDL, that person is
restricted from operating a passenger vehicle requiring 6 X X
a Group A CDL.
♦If an applicant performs the skills test in a passenger 7 X
vehicle requiring a Group C CDL, that person is
restricted from operating a passenger vehicle requiring 8 X
a Group B CDL.
♦License restricted to the operation of a city, county, 9 X
state, or federal vehicle that allowed exemption of
medical requirements under CFR §390.3(f). 10 X
Pre-trip Vehicle Inspection. You will be tested to see 11 X X X X X X
if you know whether your vehicle is safe to drive. You
will be asked to do a pre-trip inspection of your vehicle 12 X X X X X X
and explain to the examiner what you would inspect
and why. (This will require you to physically 13 X X X X X X
maneuver/crawl under the hood or under the vehicle).
*Study section 5 if you plan to operate vehicles
Basic Vehicle Control. You will be tested on your skill equipped with air brakes.
to control the vehicle. You will be asked to move your Figure 1.2
vehicle forward, backward, and turn it within a defined
area. These areas may be marked with traffic lanes,
cones, barriers, or something similar. The examiner
will tell you how each control test is to be done.
On-road Test. You will be tested on your skill to safely
drive your vehicle in a variety of traffic situations. The
situations may include left and right turns,
Section 1 - Introduction Page 1-3
7. 2009 Commercial Driver’s License Manual
1.2 – Driver Disqualifications Improper or erratic lane change including failure to
signal a lane change.
1.2.1 – General Following another vehicle too closely.
Traffic offenses committed in a CMV in connection
You may not drive a commercial motor vehicle if you with fatal traffic accidents.
are disqualified for any reason. Any railroad grade crossing violation.
Driving a CMV without obtaining a CDL license.
1.2.2 – Alcohol, Leaving the Scene of an Driving a CMV without a CDL in immediate
possession.
Accident, and Commission of a Felony
Driving a CMV without a CDL of the proper class
and/or endorsements.
It is illegal to operate a CMV if your blood alcohol
concentration (BAC) is .04% or more. If you operate a
You will lose your CDL:
CMV, you shall be deemed to have given your consent
to alcohol testing.
For not less than 60 days if convicted of two serious
traffic violations within a three-year period.
You will lose your CDL for at least one year for a first
For not less than 120 days if convicted of a third or
offense for:
subsequent serious traffic violation.
Driving a CMV if your blood alcohol concentration is
.04% or higher. 1.2.4 – Violation of Out-of-Service Orders
Driving a CMV under the influence of alcohol.
Refusing to undergo blood alcohol testing. You will lose your CDL:
Driving a CMV while under the influence of a
controlled substance. For at least 90 days if you have committed your first
Leaving the scene of an accident involving a CMV. violation of an out-of-service order.
Committing a felony involving the use of a CMV. For at least one year if you have committed two
violations of an out-of-service order in a ten-year
You will lose your CDL for at least three years if the period.
offense occurs while you are operating a CMV that is For at least three years if you have committed three or
placarded for hazardous materials. more violations of an out-of-service orders in a ten-
year period.
You will lose your CDL for life for a second or
subsequent major traffic violation. 1.2.5 – Railroad-highway Grade Crossing
Violations
You will lose your CDL for life if you use a motor
vehicle in the commission of any felony involving the You will lose your CDL:
manufacture, distribution, cultivation, sale, transfer of,
trafficking in, or dispensing of a controlled substance For at least 60 days for your first violation.
or marijuana, or possession with intent to manufacture, For at least 120 days for your second violation within
distribute, cultivate, sell, transfer, traffic in, or dispense any three-year period.
a controlled substance or marijuana. For at least one year for your third violation within any
three-year period.
You will be put out-of-service for 24 hours if you have
any detectable amount of alcohol under .04%. These violations include violation of a federal, state or
local law or regulation pertaining to one of the
1.2.3 – Serious Traffic Violations following six offenses at a railroad-highway grade
crossing:
Serious traffic violation means conviction of any of the
following offenses or a conviction of any law or For drivers who are not required to always stop, failing
ordinance equivalent thereto in this state, in any other to stop before reaching the crossing if the tracks are
state, or in any foreign jurisdiction, when operating not clear.
either a commercial motor vehicle or unless otherwise For drivers who are not required to always stop, failing
specified, a non-commercial vehicle: to slow down and check that the tracks are clear of an
approaching train.
Serious traffic violations are excessive speeding (15 For drivers who are always required to stop, failing to
mph or more above the posted limit). stop before driving onto the crossing.
Reckless driving. For all drivers failing to have sufficient space to drive
completely through the crossing without stopping.
Section 1 - Introduction Page 1-4
8. 2009 Commercial Driver’s License Manual
For all drivers failing to obey a traffic control device or
the directions of an enforcement official at the 1.2.8 – Major Traffic Violations
crossing.
For all drivers failing to negotiate a crossing because You will be disqualified from driving a CMV for not less
of insufficient undercarriage clearance. than one year if convicted of any of the following
offenses when operating either a commercial motor
1.2.6 – Hazardous Materials Endorsement vehicle or, unless otherwise specified, a
Background Check and Disqualifications noncommercial motor vehicle:
If you require a hazardous materials endorsement you Driving a vehicle under the influence in violation of
will be required to submit your fingerprints and be Code Section 40-6-391.
subject to a background check. Hit and run or leaving the scene of an accident; failing
to report striking an unattended vehicle, failure to
You will be denied or you will lose your hazardous report striking a fixed object, or failure to report an
materials endorsement if you: accident.
Are not a lawful permanent resident of the United Any felony in the commission of which a motor vehicle
States. is used.
Renounce your United States citizenship. Driving a commercial motor vehicle while the person’s
Are wanted or under indictment for certain felonies. commercial driver’s license or commercial driving
Have a conviction in military or civilian court for certain privilege is revoked, suspended, canceled, or
felonies. disqualified.
Have been adjudicated as a mental defective or Homicide by vehicle.
committed to a mental institution. Racing on highways or streets.
Are considered to pose a security threat as determined Using a motor vehicle in fleeing or attempting to elude
by the Transportation Security Administration. an officer.
Fraudulent or fictitious use of or application for a
The background check procedures vary from license.
jurisdiction to jurisdiction. Your licensing agency will Operating a motor vehicle with a revoked, canceled, or
provide you with all the information you need to suspended registration.
complete the required TSA background check Theft of a vehicle engaged in commercial
procedures (The TSA website can provide additional transportation of cargo or any appurtenance thereto or
information– www.hazprints.com). the cargo being transported therein or thereon.
Refusing to submit to a state administered chemical
1.2.7 – Traffic Violations in Your Personal test requested by a law enforcement officer.
Vehicle
If one of the offenses above occurs while you are
The Motor Carrier Safety Improvement Act (MCSIA) of operating a CMV that is placarded for hazardous
1999 requires a CDL holder to be disqualified from materials, you will be disqualified from driving a CMV
operating a commercial motor vehicle if the CDL for at least three years.
holder has been convicted of certain types of moving
violations in their personal vehicle. You will be disqualified from driving a commercial
motor vehicle for life if convicted of a second or
If your privilege to operate your personal vehicle is subsequent major traffic violation or any combination
revoked, cancelled, or suspended due to violations of of such violations from the list above.
traffic control laws (other than parking violations) you
will also lose your CDL driving privileges. 1.3 – Other CDL Rules
If your privilege to operate your personal vehicle is There are other federal and state rules that affect
revoked, cancelled, or suspended due to alcohol, drivers operating CMVs in all states. Among them are:
controlled substance or felony violations, you will lose
You cannot have more than one license. If you break
your CDL for 1 year. If you are convicted of a second
violation in your personal or CMV you will lose yourthis rule, a court may fine you up to $5,000 or put you
CDL for life. in jail and keep your home state license and return any
others.
If your license to operate your personal vehicle is You must notify your employer within 30 days of
revoked, cancelled, or suspended you may not obtain conviction for any traffic violations (except parking).
a “hardship” license to operate a CMV. This is true no matter what type of vehicle you were
driving.
Section 1 - Introduction Page 1-5
9. 2009 Commercial Driver’s License Manual
You must notify your motor vehicle licensing agency
within 30 days if you are convicted in any other
jurisdiction of any traffic violation (except parking). This
is true no matter what type of vehicle you were driving.
You must notify your employer if your license is
suspended, revoked, or canceled, or if you are
disqualified from driving.
You must give your employer information on all driving
jobs you have held for the past 10 years. You must do
this when you apply for a commercial driving job.
No one can drive a commercial motor vehicle without a
CDL. A court may fine you up to $5,000 or put you in
jail for breaking this rule.
If you have a hazardous materials endorsement you
must notify and surrender your hazardous materials
endorsement to the state that issued your CDL within
24 hours of any conviction or indictment in any
jurisdiction, civilian or military, for, or found not guilty
by reason of insanity of a disqualifying crime listed in
49 CFR 1572.103; who is adjudicated as a mental
defective or committed to a mental institution as
specified in 49 CFR 1572.109; or who renounces his
or her U. S. citizenship;
Your employer may not let you drive a commercial
motor vehicle if you have more than one license or if
you’re CDL is suspended or revoked. A court may fine
the employer up to $5,000 or put him/her in jail for
breaking this rule.
All states are connected to one computerized system
to share information about CDL drivers. The states will
check on drivers' accident records to be sure that
drivers do not have more than one CDL.
You must be properly restrained by a safety belt at all
times while operating a commercial motor vehicle.
The safety belt design holds the driver securely behind
the wheel during a crash, helping the driver to control
the vehicle and reduces the chance of serious injury or
death. If you do not wear a safety belt, you are four
times more likely to be fatally injured if you are thrown
from the vehicle.
Your state may have additional rules that you must
also obey.
Section 1 - Introduction Page 1-6
10. 2009 Commercial Driver’s License Manual
2.1 – Vehicle Inspection
Section 2
2.1.1 – Why Inspect
DRIVING SAFELY
Safety is the most important reason you inspect
This Section Covers your vehicle, safety for yourself and for other road
users.
Vehicle Inspection
A vehicle defect found during an inspection could
Basic Control of Your Vehicle
save you problems later. You could have a
Shifting Gears breakdown on the road that will cost time and
Seeing dollars, or even worse, a crash caused by the
Communicating defect.
Space Management Federal and state laws require that drivers inspect
Controlling Your Speed their vehicles. Federal and state inspectors also
Seeing Hazards may inspect your vehicles. If they judge the vehicle
Distracted Driving to be unsafe, they will put it "out of service" until it
is fixed.
Aggressive Drivers/Road Rage
Night Driving 2.1.2 – Types of Vehicle Inspection
Driving in Fog
Winter Driving Pre-trip Inspection. A pre-trip inspection will help
you find problems that could cause a crash or
Hot Weather Driving breakdown.
Railroad-highway Crossings
Mountain Driving During a Trip. For safety you should:
Driving Emergencies
Watch gauges for signs of trouble.
Antilock Braking Systems Use your senses to check for problems (look,
Skid Control and Recovery listen, smell, feel).
Accident Procedures Check critical items when you stop:
Fires Tires, wheels and rims.
Alcohol, Other Drugs, and Driving Brakes.
Staying Alert and Fit to Drive Lights and reflectors.
Hazardous Materials Rules Brake and electrical connections to trailer.
Trailer coupling devices.
This section contains knowledge and safe driving Cargo securement devices.
information that all commercial drivers should
know. You must pass a test on this information to After-trip Inspection and Report. You should do
get a CDL. This section does not have specific an after-trip inspection at the end of the trip, day, or
information on air brakes, combination vehicles, tour of duty on each vehicle you operated. It may
doubles, or passenger vehicles. When preparing include filling out a vehicle condition report listing
for the Pre-trip Inspection Test, you must review any problems you find. The inspection report helps
the material in Section 11 in addition to the a motor carrier know when the vehicle needs
information in this section. This section does have repairs.
basic information on hazardous materials (HazMat)
that all drivers should know. If you need a HazMat
endorsement, you should study Section 9.
Section 2 – Driving Safely Page 2-1
11. 2009 Commercial Driver’s License Manual
2.1.3 – What to Look For Spring hangers that allow movement of axle from
proper position. See Figure 2.2.
Tire Problems Cracked or broken spring hangers.
Missing or broken leaves in any leaf spring. If one-
Too much or too little air pressure. fourth or more are missing, it will put the vehicle
Bad wear. You need at least 4/32-inch tread depth "out of service", but any defect could be
in every major groove on front tires. You need 2/32 dangerous. See Figure 2.3.
inch on other tires. No fabric should show through Broken leaves in a multi-leaf spring or leaves that
the tread or sidewall. have shifted so they might hit a tire or other part.
Cuts or other damage. Leaking shock absorbers.
Tread separation. Torque rod or arm, u-bolts, spring hangers, or
Dual tires that come in contact with each other or other axle positioning parts that are cracked,
parts of the vehicle. damaged, or missing.
Mismatched sizes. Air suspension systems that are damaged and/or
Radial and bias-ply tires used together. leaking. See Figure 2.4.
Cut or cracked valve stems. Any loose, cracked, broken, or missing frame
Regrooved, recapped, or retreaded tires on the members.
front wheels of a bus. These are prohibited.
Wheel and Rim Problems
Damaged rims.
Rust around wheel nuts may mean the nuts are
loose--check tightness. After a tire has been
changed, stop a short while later and re-check
tightness of nuts.
Missing clamps, spacers, studs, or lugs means
danger.
Mismatched, bent, or cracked lock rings are
dangerous.
Wheels or rims that have had welding repairs are
not safe.
Bad Brake Drums or Shoes
Cracked drums.
Shoes or pads with oil, grease, or brake fluid on
them.
Shoes worn dangerously thin, missing, or broken. Figure 2.1
Steering System Defects
Missing nuts, bolts, cotter keys, or other parts.
Bent, loose, or broken parts, such as steering
column, steering gear box, or tie rods.
If power steering equipped, check hoses, pumps,
and fluid level; check for leaks.
Steering wheel play of more than 10 degrees
(approximately 2 inches movement at the rim of a
20-inch steering wheel) can make it hard to steer.
Figure 2.1 illustrates a typical steering system.
Suspension System Defects. The suspension
system holds up the vehicle and its load. It keeps
the axles in place. Therefore, broken suspension
parts can be extremely dangerous. Look for:
Section 2 – Driving Safely Page 2-2
12. 2009 Commercial Driver’s License Manual
Figure 2.4
Exhaust System Defects. A broken exhaust
system can let poison fumes into the cab or
sleeper berth. Look for:
Loose, broken, or missing exhaust pipes, mufflers,
tailpipes, or vertical stacks.
Figure 2.2 Loose, broken, or missing mounting brackets,
clamps, bolts, or nuts.
Exhaust system parts rubbing against fuel system
parts, tires, or other moving parts of vehicle.
Exhaust system parts that are leaking.
Emergency Equipment. Vehicles must be
equipped with emergency equipment. Look for:
Fire extinguisher(s).
Spare electrical fuses (unless equipped with circuit
breakers).
Warning devices for parked vehicles (for example,
three reflective warning triangles).
Cargo (Trucks). You must make sure the truck is
not overloaded and the cargo is balanced and
secured before each trip. If the cargo contains
hazardous materials, you must inspect for proper
papers and placarding.
2.1.4 – CDL Pre-trip Vehicle Inspection Test
In order to obtain a CDL you will be required to
Figure 2.3 pass a pre-trip vehicle inspection test. You will be
tested to see if you know whether your vehicle is
safe to drive. You will be asked to do a pre-trip
inspection of your vehicle and explain to the
examiner what you would inspect and why. The
following seven-step inspection method should be
useful. (This will require you to physically
maneuver/crawl under the hood/vehicle).
Section 2 – Driving Safely Page 2-3
13. 2009 Commercial Driver’s License Manual
2.1.5 – Seven-step Inspection Method Get In and Start Engine
Method of Inspection. You should do a pre-trip Make sure parking brake is on.
inspection the same way each time so you will Put gearshift in neutral (or "park" if automatic).
learn all the steps and be less likely to forget Start engine; listen for unusual noises.
something. If equipped, check the Anti-lock Braking System
(ABS) indicator lights. Light on dash should come
Approaching the Vehicle. Notice general on and then turn off. If it stays on the ABS is not
condition. Look for damage or vehicle leaning to working properly. For trailers only, if the yellow
one side. Look under the vehicle for fresh oil, light on the left rear of the trailer stays on, the ABS
coolant, grease, or fuel leaks. Check the area is not working properly.
around the vehicle for hazards to vehicle
movement (people, other vehicles, objects, low- Look at the Gauges
hanging wires, limbs, etc.).
Oil pressure. Should come up to normal within
Vehicle Inspection Guide seconds after engine is started. See Figure 2.5
Air pressure. Pressure should build from 50 to 90
Step 1: Vehicle Overview psi within 3 minutes. Build air pressure to governor
cut-out (usually around 120 – 140 psi. Know your
Review Last Vehicle Inspection Report. Drivers vehicles requirements.
may have to make a vehicle inspection report in Ammeter and/or voltmeter. Should be in normal
writing each day. The motor carrier must repair any range(s).
items in the report that affect safety and certify on Coolant temperature. Should begin gradual rise to
the report that repairs were made or were normal operating range.
unnecessary. You must sign the report only if Engine oil temperature. Should begin gradual rise
defects were noted and certified to be repaired or to normal operating range.
not needed to be repaired. Warning lights and buzzers. Oil, coolant, charging
circuit warning, and antilock brake system lights
Step 2: Check Engine Compartment should go out right away.
Check That the Parking Brakes Are On and/or Check Condition of Controls. Check all of the
Wheels Chocked. You may have to raise the following for looseness, sticking, damage, or
hood, tilt the cab (secure loose things so they don't improper setting:
fall and break something), or open the engine
compartment door. Check the following: Steering wheel.
Clutch.
Engine oil level. Accelerator ("gas pedal").
Coolant level in radiator; condition of hoses. Brake controls.
Power steering fluid level; hose condition (if so
equipped). Foot brake.
Windshield washer fluid level. Trailer brake (if vehicle has one).
Battery fluid level, connections, and tie downs Parking brake.
(battery may be located elsewhere). Retarder controls (if vehicle has them).
Automatic transmission fluid level (may require
engine to be running). Transmission controls.
Check belts for tightness and excessive wear Interaxle differential lock (if vehicle has one).
(alternator, water pump, air compressor)--learn Horn(s).
how much "give" the belts should have when Windshield wiper/washer.
adjusted right, and check each one. Lights.
Leaks in the engine compartment (fuel, coolant, oil,
power steering fluid, hydraulic fluid, battery fluid). Headlights.
Cracked, worn electrical wiring insulation. Dimmer switch.
Turn signal.
Lower and secure hood, cab, or engine Four-way flashers.
compartment door. Parking, clearance, identification, marker
switch(es).
Step 3: Start Engine and Inspect Inside the Cab
Section 2 – Driving Safely Page 2-4
14. 2009 Commercial Driver’s License Manual
headlights (low beams) and four-way emergency
flashers, and get out of the vehicle.
Step 5: Do Walkaround Inspection
Go to front of vehicle and check that low beams
are on and both of the four-way flashers are
working.
Push dimmer switch and check that high beams
work.
Turn off headlights and four-way emergency
flashers.
Turn on parking, clearance, side-marker, and
identification lights.
Turn on right turn signal, and start walk-around
inspection.
General
Walkaround and inspect.
Clean all lights, reflectors, and glass as you go
along.
Figure 2.5
Left Front Side
Check Mirrors and Windshield. Inspect mirrors
and windshield for cracks, dirt, illegal stickers, or Driver's door glass should be clean.
other obstructions to seeing clearly. Clean and Door latches or locks should work properly.
adjust as necessary. Left front wheel.
Check Emergency Equipment Condition of wheel and rim--missing, bent,
broken studs, clamps, lugs, or any signs of
Check for safety equipment: misalignment.
Condition of tires--properly inflated, valve
Spare electrical fuses (unless vehicle has stem and cap OK, no serious cuts, bulges,
circuit breakers). or tread wear.
Three red reflective triangles. Use wrench to test rust-streaked lug nuts,
Properly charged and rated fire indicating looseness.
extinguisher. Hub oil level OK, no leaks.
Check for optional items such as: Left front suspension.
Chains (where winter conditions require). Condition of spring, spring hangers,
Tire changing equipment. shackles, u-bolts.
Shock absorber condition.
Check Safety Belt. Check that the safety belt is
securely mounted, adjusts, latches properly, and is Left front brake.
not ripped or frayed.
Condition of brake drum or disc.
List of emergency phone numbers. Condition of hoses.
Accident reporting kit (packet).
Front
Step 4: Turn Off Engine and Check Lights
Condition of front axle.
Make sure the parking brake is set, turn off the Condition of steering system.
engine, and take the key with you. Turn on
Section 2 – Driving Safely Page 2-5
15. 2009 Commercial Driver’s License Manual
No loose, worn, bent, damaged or missing Header board adequate, secure (if
parts. required).
Must grab steering mechanism to test for Side boards, stakes strong enough, free of
looseness. damage, properly set in place (if so
equipped).
Condition of windshield. Canvas or tarp (if required) properly
Check for damage and clean if dirty. secured to prevent tearing, billowing, or
Check windshield wiper arms for proper blocking of mirrors.
spring tension. If oversize, all required signs (flags, lamps,
Check wiper blades for damage, "stiff" and reflectors) safely and properly
rubber, and securement. mounted and all required permits in
driver's possession.
Lights and reflectors. Curbside cargo compartment doors in
good condition, securely closed,
Parking, clearance, and identification lights latched/locked and required security seals
clean, operating, and proper color (amber in place.
at front).
Reflectors clean and proper color (amber Right Rear
at front).
Right front turn signal light clean, Condition of wheels and rims--no missing, bent, or
operating, and proper color (amber or broken spacers, studs, clamps, or lugs.
white on signals facing forward). Condition of tires--properly inflated, valve stems
and caps OK, no serious cuts, bulges, tread wear,
Right Side tires not rubbing each other, and nothing stuck
between them.
Right front: check all items as done on left front. Tires same type, e.g., not mixed radial and bias
Primary and secondary safety cab locks engaged types.
(if cab-over-engine design). Tires evenly matched (same sizes).
Right fuel tank(s). Wheel bearing/seals not leaking.
Suspension.
Securely mounted, not damaged, or
leaking. Condition of spring(s), spring hangers,
Fuel crossover line secure. shackles, and u-bolts.
Tank(s) contain enough fuel. Axle secure.
Cap(s) on and secure. Powered axle(s) not leaking lube (gear oil).
Condition of torque rod arms, bushings.
Condition of visible parts. Condition of shock absorber(s).
If retractable axle equipped, check
Rear of engine--not leaking. condition of lift mechanism. If air powered,
Transmission--not leaking. check for leaks.
Exhaust system--secure, not leaking, not Condition of air ride components.
touching wires, fuel, or air lines.
Frame and cross members--no bends or Brakes.
cracks.
Air lines and electrical wiring--secured Brake adjustment.
against snagging, rubbing, wearing. Condition of brake drum(s) or discs.
Spare tire carrier or rack not damaged (if Condition of hoses--look for any wear due
so equipped). to rubbing.
Spare tire and/or wheel securely mounted
in rack. Lights and reflectors.
Spare tire and wheel adequate (proper
size, properly inflated). Side-marker lights clean, operating, and
proper color (red at rear, others amber).
Cargo securement (trucks). Side-marker reflectors clean and proper
color (red at rear, others amber).
Cargo properly blocked, braced, tied,
chained, etc.
Section 2 – Driving Safely Page 2-6
16. 2009 Commercial Driver’s License Manual
Rear Step 6: Check Signal Lights
Lights and reflectors. Get In and Turn Off Lights
Rear clearance and identification lights Turn off all lights.
clean, operating, and proper color (red at Turn on stop lights (apply trailer hand brake or
rear). have a helper put on the brake pedal).
Reflectors clean and proper color (red at Turn on left turn signal lights.
rear).
Taillights clean, operating, and proper Get Out and Check Lights
color (red at rear).
Right rear turn signal operating, and Left front turn signal light clean, operating and
proper color (red, yellow, or amber at rear). proper color (amber or white on signals facing the
front).
License plate(s) present, clean, and secured. Left rear turn signal light and both stop lights clean,
Splash guards present, not damaged, properly operating, and proper color (red, yellow, or amber).
fastened, not dragging on ground, or rubbing tires.
Cargo secure (trucks). Get In Vehicle
Cargo properly blocked, braced, tied, chained, etc.
Tailboards up and properly secured. Turn off lights not needed for driving.
End gates free of damage, properly secured in Check for all required papers, trip manifests,
stake sockets. permits, etc.
Canvas or tarp (if required) properly secured to Secure all loose articles in cab (they might interfere
prevent tearing, billowing, or blocking of either the with operation of the controls or hit you in a crash).
rearview mirrors or rear lights. Start the engine.
If over-length, or over-width, make sure all signs
and/or additional lights/flags are safely and Step 7: Start the Engine and Check
properly mounted and all required permits are in
driver's possession. Test for Hydraulic Leaks. If the vehicle has
Rear doors securely closed, latched/locked. hydraulic brakes, pump the brake pedal three
times. Then apply firm pressure to the pedal and
Left Side hold for five seconds. The pedal should not move.
If it does, there may be a leak or other problem.
Check all items as done on right side, plus: Get it fixed before driving. If the vehicle has air
brakes, do the checks described in Sections 5 and
Battery(ies) (if not mounted in engine 6 of this manual.
compartment).
Battery box(es) securely mounted to Brake System
vehicle.
Box has secure cover. Test Parking Brake(s)
Battery(ies) secured against movement. Fasten safety belt
Battery(ies) not broken or leaking. Set parking brake (power unit only).
Fluid in battery(ies) at proper level (except Release trailer parking brake (if applicable).
maintenance-free type). Place vehicle into a low gear.
Cell caps present and securely tightened Gently pull forward against parking brake to make
(except maintenance-free type). sure the parking brake holds.
Vents in cell caps free of foreign material Repeat the same steps for the trailer with trailer
(except maintenance-free type). parking brake set and power unit parking brakes
released (if applicable).
If it doesn't hold vehicle, it is faulty; get it fixed.
Section 2 – Driving Safely Page 2-7
17. 2009 Commercial Driver’s License Manual
Test Service Brake Stopping Action
1. What is the most important reason for
Go about five miles per hour. doing a vehicle inspection?
Push brake pedal firmly 2. What things should you check during a
"Pulling" to one side or the other can mean brake trip?
trouble. 3. Name some key steering system parts.
Any unusual brake pedal "feel" or delayed stopping 4. Name some suspension system defects.
action can mean trouble. 5. What three kinds of emergency equipment
must you have?
If you find anything unsafe during the pre-trip 6. What is the minimum tread depth for front
inspection, get it fixed. Federal and state laws tires? For other tires?
forbid operating an unsafe vehicle. 7. Name some things you should check on
the front of your vehicle during the
2.1.6 – Inspection During a Trip walkaround inspection.
8. What should wheel bearing seals be
Check Vehicle Operation Regularly checked for?
9. How many red reflective triangles should
You should check: you carry?
10. How do you test hydraulic brakes for
Instruments. leaks?
Air pressure gauge (if you have air brakes). 11. Why put the starter switch key in your
Temperature gauges. pocket during the pre-trip inspection?
Pressure gauges.
Ammeter/voltmeter. These questions may be on your test. If you can’t
Mirrors. answer them all, re-read subsection 2.1.
Tires.
Cargo, cargo covers.
Lights.
Etc. 2.2 – Basic Control of Your Vehicle
If you see, hear, smell, or feel anything that might To drive a vehicle safely, you must be able to
mean trouble, check it out. control its speed and direction. Safe operation of a
commercial vehicle requires skill in:
Safety Inspection. Drivers of trucks and truck
tractors when transporting cargo must inspect the Accelerating.
securement of the cargo within the first 50 miles of Steering.
a trip and every 150 miles or every three hours Stopping.
(whichever comes first) after. Backing safely.
2.1.7 – After-trip Inspection and Report Fasten your seatbelt when on the road. Apply the
parking brake when you leave your vehicle.
You may have to make a written report each day
on the condition of the vehicle(s) you drove. Report
anything affecting safety or possibly leading to 2.2.1 – Accelerating
mechanical breakdown.
Don't roll back when you start. You may hit
someone behind you. If you have a manual
transmission vehicle, partly engage the clutch
before you take your right foot off the brake. Put on
the parking brake whenever necessary to keep
Subsection 2.1
from rolling back. Release the parking brake only
Test Your Knowledge when you have applied enough engine power to
keep from rolling back. On a tractor-trailer
The vehicle inspection report tells the motor carrier equipped with a trailer brake hand valve, the hand
about problems that may need fixing. Keep a copy valve can be applied to keep from rolling back.
of your report in the vehicle for one day. That way, Speed up smoothly and gradually so the vehicle
the next driver can learn about any problems you does not jerk. Rough acceleration can cause
have found.
Section 2 – Driving Safely Page 2-8
18. 2009 Commercial Driver’s License Manual
mechanical damage. When pulling a trailer, rough Use Mirrors on Both Sides. Check the outside
acceleration can damage the coupling. mirrors on both sides frequently. Get out of the
vehicle and check your path if you are unsure.
Speed up very gradually when traction is poor, as
in rain or snow. If you use too much power, the Back Slowly. Always back as slowly as possible.
drive wheels may spin. You could lose control. If Use the lowest reverse gear. That way you can
the drive wheels begin to spin, take your foot off more easily correct any steering errors. You also
the accelerator. can stop quickly if necessary.
2.2.2 – Steering Back and Turn Toward the Driver's Side. Back
to the driver's side so you can see better. Backing
Hold the steering wheel firmly with both hands. toward the right side is very dangerous because
Your hands should be on opposite sides of the you can't see as well. If you back and turn toward
wheel. If you hit a curb or a pothole (chuckhole), the driver's side, you can watch the rear of your
the wheel could pull away from your hands unless vehicle by looking out the side window. Use driver-
you have a firm hold. side backing--even if it means going around the
block to put your vehicle in this position. The
2.2.3 – Stopping added safety is worth it.
Push the brake pedal down gradually. The amount Use a Helper. Use a helper when you can. There
of brake pressure you need to stop the vehicle will are blind spots you can't see. That's why a helper
depend on the speed of the vehicle and how is important. The helper should stand near the
quickly you need to stop. Control the pressure so back of your vehicle where you can see the helper.
the vehicle comes to a smooth, safe stop. If you Before you begin backing, work out a set of hand
have a manual transmission, push the clutch in signals that you both understand. Agree on a
when the engine is close to idle. signal for "stop."
2.2.4 – Backing Safely 2.3 – Shifting Gears
Because you cannot see everything behind your Correct shifting of gears is important. If you can't
vehicle, backing is always dangerous. Avoid get your vehicle into the right gear while driving,
backing whenever you can. When you park, try to you will have less control.
park so you will be able to pull forward when you
leave. When you have to back, here are a few 2.3.1 – Manual Transmissions
simple safety rules:
Basic Method for Shifting Up. Most heavy
Start in the proper position. vehicles with manual transmissions require double
Look at your path. clutching to change gears. This is the basic
Use mirrors on both sides. method:
Back slowly.
Back and turn toward the driver's side whenever Release accelerator, push in clutch and shift to
possible. neutral at the same time.
Use a helper whenever possible. Release clutch.
These rules are discussed in turn below. Let engine and gears slow down to the rpm
required for the next gear (this takes practice).
Start in the Proper Position. Put the vehicle in Push in clutch and shift to the higher gear at the
the best position to allow you to back safely. This same time.
position will depend on the type of backing to be Release clutch and press accelerator at the same
done. time.
Look at Your Path. Look at your line of travel Shifting gears using double clutching requires
before you begin. Get out and walk around the practice. If you remain too long in neutral, you may
vehicle. Check your clearance to the sides and have difficulty putting the vehicle into the next
overhead, in and near the path your vehicle will gear. If so, don't try to force it. Return to neutral,
take. release clutch, increase engine speed to match
road speed, and try again.
Section 2 – Driving Safely Page 2-9
19. 2009 Commercial Driver’s License Manual
Knowing When to Shift Up. There are two ways Multi-speed rear axles and auxiliary transmissions
of knowing when to shift: are used on many vehicles to provide extra gears.
You usually control them by a selector knob or
Use Engine Speed (rpm). Study the driver's switch on the gearshift lever of the main
manual for your vehicle and learn the operating transmission. There are many different shift
rpm range. Watch your tachometer, and shift up patterns. Learn the right way to shift gears in the
when your engine reaches the top of the range. vehicle you will drive.
(Some newer vehicles use "progressive" shifting:
the rpm at which you shift becomes higher as you 2.3.3 – Automatic Transmissions
move up in the gears. Find out what's right for the
vehicle you will operate.) Some vehicles have automatic transmissions. You
can select a low range to get greater engine
Use Road Speed (mph). Learn what speeds each braking when going down grades. The lower
gear is good for. Then, by using the speedometer, ranges prevent the transmission from shifting up
you'll know when to shift up. beyond the selected gear (unless the governor rpm
is exceeded). It is very important to use this
With either method, you may learn to use engine braking effect when going down grades.
sounds to know when to shift.
2.3.4 – Retarders
Basic Procedures for Shifting Down
Some vehicles have "retarders." Retarders help
Release accelerator, push in clutch, and shift to slow a vehicle, reducing the need for using your
neutral at the same time. brakes. They reduce brake wear and give you
Release clutch. another way to slow down. There are four basic
Press accelerator, increase engine and gear speed types of retarders (exhaust, engine, hydraulic, and
to the rpm required in the lower gear. electric). All retarders can be turned on or off by
Push in clutch and shift to lower gear at the same the driver. On some vehicles the retarding power
time. can be adjusted. When turned "on," retarders apply
Release clutch and press accelerator at the same their braking power (to the drive wheels only)
time. whenever you let up on the accelerator pedal all
Downshifting, like upshifting, requires knowing the way.
when to shift. Use either the tachometer or the
speedometer and downshift at the right rpm or Because these devices can be noisy, be sure you
road speed. know where their use is permitted.
Special conditions where you should downshift Caution. When your drive wheels have poor
are: traction, the retarder may cause them to skid.
Therefore, you should turn the retarder off
Before Starting Down a Hill. Slow down and shift whenever the road is wet, icy, or snow covered.
down to a speed that you can control without using
the brakes hard. Otherwise the brakes can
overheat and lose their braking power.
Downshift before starting down the hill. Make sure Subsections 2.2 and 2.3
you are in a low enough gear, usually lower than Test Your Knowledge
the gear required to climb the same hill.
1. Why should you back toward the driver's
Before Entering a Curve. Slow down to a safe side?
speed, and downshift to the right gear before 2. If stopped on a hill, how can you start
entering the curve. This lets you use some power moving without rolling back?
through the curve to help the vehicle be more 3. When backing, why is it important to use a
stable while turning. It also allows you to speed up helper?
as soon as you are out of the curve. 4. What's the most important hand signal that
you and the helper should agree on?
2.3.2 – Multi-speed Rear Axles and 5. What are the two special conditions where
Auxiliary Transmissions you should downshift?
Section 2 – Driving Safely Page 2-10
20. 2009 Commercial Driver’s License Manual
6. When should you downshift automatic Look for Traffic. Look for vehicles coming onto
transmissions? the highway, into your lane, or turning. Watch for
7. Retarders keep you from skidding when brake lights from slowing vehicles. By seeing these
the road is slippery. True or False? things far enough ahead, you can change your
8. What are the two ways to know when to speed, or change lanes if necessary to avoid a
shift? problem. If a traffic light has been green for a long
time it will probably change before you get there.
These questions may be on the test. If you can't Start slowing down and be ready to stop.
answer them all, re-read subsections 2.2 and 2.3.
2.4.2 – Seeing to the Sides and Rear
2.4 – Seeing It's important to know what's going on behind and
to the sides. Check your mirrors regularly. Check
To be a safe driver you need to know what's going more often in special situations.
on all around your vehicle. Not looking properly is a
major cause of accidents. Mirror Adjustment. Mirror adjustment should be
checked prior to the start of any trip and can only
2.4.1 – Seeing Ahead be checked accurately when the trailer(s) are
straight. You should check and adjust each mirror
All drivers look ahead; but many don't look far to show some part of the vehicle. This will give you
enough ahead. a reference point for judging the position of the
other images.
Importance of Looking Far Enough Ahead.
Because stopping or changing lanes can take a lot Regular Checks. You need to make regular
of distance, knowing what the traffic is doing on all checks of your mirrors to be aware of traffic and to
sides of you is very important. You need to look check your vehicle.
well ahead to make sure you have room to make
these moves safely. Traffic. Check your mirrors for vehicles on either
side and in back of you. In an emergency, you may
How Far Ahead to Look. Most good drivers look need to know whether you can make a quick lane
at least 12 to 15 seconds ahead. That means change. Use your mirrors to spot overtaking
looking ahead the distance you will travel in 12 to vehicles. There are "blind spots" that your mirrors
15 seconds. At lower speeds, that's about one cannot show you. Check your mirrors regularly to
block. At highway speeds it's about a quarter of a know where other vehicles are around you, and to
mile. If you're not looking that far ahead, you may see if they move into your blind spots.
have to stop too quickly or make quick lane
changes. Looking 12 to 15 seconds ahead doesn't Check Your Vehicle. Use the mirrors to keep an
mean not paying attention to things that are closer. eye on your tires. It's one way to spot a tire fire. If
Good drivers shift their attention back and forth, you're carrying open cargo, you can use the
near and far. Figure 2.6 illustrates how far to look mirrors to check it. Look for loose straps, ropes, or
ahead. chains. Watch for a flapping or ballooning tarp.
Special Situations. Special situations require
more than regular mirror checks. These are lane
changes, turns, merges, and tight maneuvers.
Lane Changes. You need to check your mirrors to
make sure no one is alongside you or about to
pass you. Check your mirrors:
Before you change lanes to make sure there is
enough room.
After you have signaled, to check that no one has
moved into your blind spot.
Right after you start the lane change, to double-
check that your path is clear.
After you complete the lane change.
Figure 2.6
Section 2 – Driving Safely Page 2-11
21. 2009 Commercial Driver’s License Manual
Turns. In turns, check your mirrors to make sure 2.5 – Communicating
the rear of your vehicle will not hit anything.
Merges. When merging, use your mirrors to make 2.5.1 – Signal Your Intentions
sure the gap in traffic is large enough for you to
enter safely. Other drivers can't know what you are going to do
until you tell them.
Tight Maneuvers. Any time you are driving in
close quarters, check your mirrors often. Make
Signaling what you intend to do is important for
sure you have enough clearance.
safety. Here are some general rules for signaling.
How to Use Mirrors. Use mirrors correctly by
checking them quickly and understanding what you Turns. There are three good rules for using turn
see. signals:
When you use your mirrors while driving on the Signal early. Signal well before you turn. It is the
road, check quickly. Look back and forth between best way to keep others from trying to pass you.
the mirrors and the road ahead. Don't focus on the Signal continuously. You need both hands on the
mirrors for too long. Otherwise, you will travel quite wheel to turn safely. Don't cancel the signal until
a distance without knowing what's happening you have completed the turn.
ahead. Cancel your signal. Don't forget to turn off your turn
Many large vehicles have curved (convex, signal after you've turned (if you don't have self-
"fisheye," "spot," "bugeye") mirrors that show a canceling signals).
wider area than flat mirrors. This is often helpful.
But everything appears smaller in a convex mirror Lane Changes. Put your turn signal on before
than it would if you were looking at it directly. changing lanes. Change lanes slowly and
Things also seem farther away than they really are. smoothly. That way a driver you didn't see may
It's important to realize this and to allow for it. have a chance to honk his/her horn, or avoid your
Figure 2.7 shows the field of vision using a convex vehicle.
mirror.
Slowing Down. Warn drivers behind you when
you see you'll need to slow down. A few light taps
on the brake pedal -- enough to flash the brake
lights -- should warn following drivers. Use the
four-way emergency flashers for times when you
are driving very slowly or are stopped. Warn other
drivers in any of the following situations:
Trouble Ahead. The size of your vehicle may make
it hard for drivers behind you to see hazards
ahead. If you see a hazard that will require slowing
down, warn the drivers behind by flashing your
brake lights.
Tight Turns. Most car drivers don't know how
slowly you have to go to make a tight turn in a
large vehicle. Give drivers behind you warning by
braking early and slowing gradually.
Stopping on the Road. Truck and bus drivers
sometimes stop in the roadway to unload cargo or
passengers, or to stop at a railroad crossing. Warn
following drivers by flashing your brake lights.
Don't stop suddenly.
Driving Slowly. Drivers often do not realize how
fast they are catching up to a slow vehicle until
they are very close. If you must drive slowly, alert
following drivers by turning on your emergency
flashers if it is legal. (Laws regarding the use of
Figure 2.7 flashers differ from one state to another. Check the
laws of the states where you will drive.)
Section 2 – Driving Safely Page 2-12
22. 2009 Commercial Driver’s License Manual
Don't Direct Traffic. Some drivers try to help out
others by signaling when it is safe to pass. You
should not do this. You could cause an accident.
You could be blamed and it could cost you many
thousands of dollars.
2.5.2 – Communicating Your Presence
Other drivers may not notice your vehicle even
when it's in plain sight. To help prevent accidents,
let them know you're there.
When Passing. Whenever you are about to pass
a vehicle, pedestrian, or bicyclist, assume they
don't see you. They could suddenly move in front
of you. When it is legal, tap the horn lightly or, at
night, flash your lights from low to high beam and
back. And, drive carefully enough to avoid a crash
even if they don't see or hear you.
When It's Hard to See. At dawn, dusk, in rain, or
snow, you need to make yourself easier to see. If
Figure 2.8
you are having trouble seeing other vehicles, other
drivers will have trouble seeing you. Turn on your
lights. Use the headlights, not just the identification
or clearance lights. Use the low beams; high
beams can bother people in the daytime as well as
at night.
When Parked at the Side of the Road. When you
pull off the road and stop, be sure to turn on the
four-way emergency flashers. This is important at
night. Don't trust the taillights to give warning.
Drivers have crashed into the rear of a parked
vehicle because they thought it was moving
normally.
If you must stop on a road or the shoulder of any
road, you must put out your emergency warning
devices within ten minutes. Place your warning
devices at the following locations:
If you must stop on or by a one-way or divided
highway, place warning devices 10 feet, 100 feet,
and 200 feet toward the approaching traffic. See
Figure 2.8.
Figure 2.9
If you stop on a two-lane road carrying traffic in
both directions or on an undivided highway, place Back beyond any hill, curve, or other obstruction
warning devices within 10 feet of the front or rear that prevents other drivers from seeing the vehicle
corners to mark the location of the vehicle and 100 within 500 feet. If line of sight view is obstructed
feet behind and ahead of the vehicle, on the due to hill or curve, move the rear-most triangle to
shoulder or in the lane you stopped in. See Figure a point back down the road so warning is provided.
2.9. See Figure 2.10.
Section 2 – Driving Safely Page 2-13
23. 2009 Commercial Driver’s License Manual
Reaction Distance. The distance traveled from
the time your brain tells your foot to move from the
accelerator until your foot is actually pushing the
brake pedal. The average driver has a reaction
time of 3/4 second. This accounts for an additional
60 feet traveled at 55 mph.
Braking Distance. The distance it takes to stop
once the brakes are put on. At 55 mph on dry
pavement with good brakes, it can take a heavy
vehicle about 390 feet to stop. It takes about 4 1/2
seconds.
Total Stopping Distance. At 55 mph, it will take
about six seconds to stop and your vehicle will
travel about 450 feet.
The Effect of Speed on Stopping Distance.The
faster you drive, the greater the impact or striking
power of your vehicle. When you double your
speed from 20 to 40 mph the impact is 4 times
greater. The braking distance is also 4 times
longer. Triple the speed from 20 to 60 mph and
the impact and braking distance is 9 times greater.
At 60 mph, your stopping distance is greater than
Figure 2.10 that of a football field. Increase the speed to 80
mph and the impact and braking distance are 16
When putting out the triangles, hold them between times greater than at 20 mph. High speeds greatly
yourself and the oncoming traffic for your own increase the severity of crashes and stopping
safety. (So other drivers can see you.) distances. By slowing down, you can reduce
braking distance. See Figure 2.11
Use Your Horn When Needed. Your horn can let
others know you're there. It can help to avoid a
crash. Use your horn when needed. However, it
can startle others and could be dangerous when
used unnecessarily.
2.6 – Controlling Speed
Driving too fast is a major cause of fatal crashes.
You must adjust your speed depending on driving
conditions. These include traction, curves, visibility,
traffic and hills.
2.6.1 – Stopping Distance
Perception Distance + Reaction Distance +
Braking Distance =Total Stopping Distance
Perception Distance. This is the distance your
vehicle travels from the time your eyes see a
hazard until your brain recognizes it. The
perception time for an alert driver is about 3/4
second. At 55 mph, you travel 60 feet in 3/4
Figure 2.11
second or about 81 feet per second.
Section 2 – Driving Safely Page 2-14
24. 2009 Commercial Driver’s License Manual
tires lose their contact with the road and have little
The Effect of Vehicle Weight on Stopping or no traction. You may not be able to steer or
Distance. The heavier the vehicle, the more work brake. You can regain control by releasing the
the brakes must do to stop it, and the more heat accelerator and pushing in the clutch. This will slow
they absorb. But the brakes, tires, springs, and your vehicle and let the wheels turn freely. If the
shock absorbers on heavy vehicles are designed vehicle is hydroplaning, do not use the brakes to
to work best when the vehicle is fully loaded. slow down. If the drive wheels start to skid, push in
Empty trucks require greater stopping distances the clutch to let them turn freely.
because an empty vehicle has less traction.
It does not take a lot of water to cause
2.6.2 – Matching Speed to the Road hydroplaning. Hydroplaning can occur at speeds
Surface as low as 30 mph if there is a lot of water.
Hydroplaning is more likely if tire pressure is low,
You can't steer or brake a vehicle unless you have or the tread is worn. (The grooves in a tire carry
traction. Traction is friction between the tires and away the water; if they aren't deep, they don't work
the road. There are some road conditions that well.)
reduce traction and call for lower speeds.
Road surfaces where water can collect can create
Slippery Surfaces. It will take longer to stop, and conditions that cause a vehicle to hydroplane.
it will be harder to turn without skidding, when the Watch for clear reflections, tire splashes, and
road is slippery. Wet roads can double stopping raindrops on the road. These are indications of
distance. You must drive slower to be able to stop standing water.
in the same distance as on a dry road. Reduce
speed by about one-third (e.g., slow from 55 to 2.6.3 – Speed and Curves
about 35 mph) on a wet road. On packed snow,
reduce speed by a half, or more. If the surface is Drivers must adjust their speed for curves in the
icy, reduce speed to a crawl and stop driving as road. If you take a curve too fast, two things can
soon as you can safely do so. happen. The tires can lose their traction and
continue straight ahead, so you skid off the road.
Identifying Slippery Surfaces. Sometimes it's Or, the tires may keep their traction and the vehicle
hard to know if the road is slippery. Here are some rolls over. Tests have shown that trucks with a high
signs of slippery roads: center of gravity can roll over at the posted speed
limit for a curve.
Shaded Areas. Shady parts of the road will remain
icy and slippery long after open areas have melted. Slow to a safe speed before you enter a curve.
Bridges. When the temperature drops, bridges will Braking in a curve is dangerous because it is
freeze before the road will. Be especially careful easier to lock the wheels and cause a skid. Slow
when the temperature is close to 32 degrees down as needed. Don't ever exceed the posted
Fahrenheit. speed limit for the curve. Be in a gear that will let
Melting Ice. Slight melting will make ice wet. Wet you accelerate slightly in the curve. This will help
ice is much more slippery than ice that is not wet. you keep control.
Black Ice. Black ice is a thin layer that is clear
enough that you can see the road underneath it. It 2.6.4 – Speed and Distance Ahead
makes the road look wet. Any time the temperature
is below freezing and the road looks wet, watch out You should always be able to stop within the
for black ice. distance you can see ahead. Fog, rain, or other
Vehicle Icing. An easy way to check for ice is to conditions may require that you slow down to be
open the window and feel the front of the mirror, able to stop in the distance you can see. At night,
mirror support, or antenna. If there's ice on these, you can't see as far with low beams as you can
the road surface is probably starting to ice up. with high beams. When you must use low beams,
Just After Rain Begins. Right after it starts to slow down.
rain, the water mixes with oil left on the road by
vehicles. This makes the road very slippery. If the 2.6.5 – Speed and Traffic Flow
rain continues, it will wash the oil away.
Hydroplaning. In some weather, water or slush When you're driving in heavy traffic, the safest
collects on the road. When this happens, your speed is the speed of other vehicles. Vehicles
vehicle can hydroplane. It's like water skiing--the going the same direction at the same speed are
Section 2 – Driving Safely Page 2-15