International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Presentation J.W.M.M. Van Hellenberg Hubar Mid Term Colloquium 2011 07 13
Report
Share
1 of 4
Download to read offline
More Related Content
Bl36378381
1. Vijaya Lalita. P et al Int. Journal of Engineering Research and Application
ISSN : 2248-9622, Vol. 3, Issue 6, Nov-Dec 2013, pp.378-381
RESEARCH ARTICLE
www.ijera.com
OPEN ACCESS
Energy and Comfort Management in Energy Efficient Buildings
Using RETSCREEN Software-A Case Study Analysis
Vijaya Lalita. P*, Dr. Ch. Saibabu**, G. R. K. D. Satya Prasad***
*(PG Student, JNTUK, Kakinada, Andhra Pradesh)
** (Professor in EEE, Director of Academic Planning JNTUK; Kakinada, Andhra Pradesh, INDIA)
***
(Research Scholar, JNTU Kakinada, Assoc. Professor, GIET, Gunupur, ODISHA)
ABSTRACT
Smart and energy-efficient buildings have recently become a trend for future building industry. The major
challenge in the control system design for such a building is to minimize the power consumption without
compromising the customers comfort. Buildings have the physical potential to harness diluted and sometimes
unpredictable renewable energy. The building envelope and the ground constitute the basic resources for energy
autonomous buildings. It is widely accepted that if any country has to reduce greenhouse gas emissions it must
aggressively address energy end use in the building sector.
Simulation of building performance is increasingly being used in design practice to predict comfort of occupants
in finished buildings. In this thesis, the simulation results shows that the proposed intelligent control system
successfully manages the user’s preferences for thermal and illuminance comfort, indoor air quality and the
energy conservation by using RETSCREEN software. The present work attempts to overcome certain
inadequacies of contemporary simulation applications with respect to environmental control systems, by
developing novel building control systems modeling schemes. These schemes are then integrated within a stateof-art simulation environment so that they can be employed in practice.
Keywords – Building materials, Energy Efficient buildings, Energy performance index, HVAC parameters,
RETSCREEN software.
I.
INTRODUCTION
Energy consumption of buildings (both
residential and commercial) has steadily increased,
reaching figures between 20% and 40% in developed
countries. The rise of energy demand in buildings will
continue in the near future because of growth in
population, long-term use of buildings, and increasing
demand for improved building comfort levels.
Therefore, the energy efficiency of buildings is of
prime concern for anyone wishing to identify energy
savings. To this end, automated meter reading and
smart metering systems have been employed to collect
building energy data [1]. The aim of these data is to
provide greater insight into how a building consumes
energy and, therefore, what improvements are likely to
be most effective in reducing consumption. Energy
Efficient Building (EEB) design has become a high
priority for present situations where power crisis is
escalating to higher levels. The present study of EEB
is a challenging task for multi-disciplinary technology,
because designing a EEB involves the knowledge of
civil, mechanical, electrical, environmental and
architectural engineers. The scientific evidences for
climate changes and the associated impacts of
greenhouse gas emissions are becoming increasingly
obvious. Most of the countries, buildings are
responsible for 47% of national energy consumption.
Scientists and built environment professionals are
trying to find advanced technologies, renewable
www.ijera.com
energies, and useful strategies to reduce carbon
dioxide emissions [2].
The concept of EEB has gained wide
international attention during last few years and is
now seen as the future target for the design of
buildings. However, before being fully implemented
in the national building codes and international
standards, the EEB concept requires clear and
consistent definition and a commonly agreed energy
calculation methodology.
This paper focuses on the review of the most
of the existing EEB definitions and the various
approaches towards possible EEB calculation
methodologies. It presents and discusses possible
answers to the above mentioned issues in order to
facilitate the development of a consistent EEB
definition
and
robust
energy
calculation
methodologies are provided [3].
II.
AN APPROACH TO PLAN EEB
Buildings are usually evaluated according to
the amount of energy required by the building and
therefore expressed in terms of kWh/m2/year and
termed as Energy Performance Index (EPI). The
assessment of the energy demand for the climatic
control of a building can only be dealt with if the level
of the indoor environmental comfort and it is directly
related to EPI. If the value of EPI is less, then the
consumption of energy is less and hence the electricity
378 | P a g e
2. Vijaya Lalita. P et al Int. Journal of Engineering Research and Application
ISSN : 2248-9622, Vol. 3, Issue 6, Nov-Dec 2013, pp.378-381
bills will be less. But, all these can be achieved without
compromising the comforts and luxuries of the
consumer.
A systematic approach is required to plan an
EEB without sacrificing the requirements of the
consumer. A good EEB design requires the
technologies of civil, thermal, mechanical, electrical
and architectural tools. Hence the below flow chart
shown in “Fig.1” will gives an approach to plan an
EEB.
www.ijera.com
Where, qH is the thermal load of the building
in watts. The first two terms on the right express the
thermal losses (
), which is the
more important part of any building study, while the
last two terms are the thermal gains of the building
qcond are the thermal losses through the building’s
envelope, qinf are the infiltration loss caused by the
entrance of fresh air. Respectively, qsol are the net solar
thermal gains and qint are the internal thermal gains
(people, lighting, equipment operation etc.).
Fig.2: Building model
Fig. 1: Planning of an EEB through flow chart
A base building will be measured with initial
EPI and if it measures 350 kwh/m2/year. By envelope
optimization and with building materials in roof and
walls the EPI can decrease to 225 kWh /m2/year.
Similarly with lighting optimization to 175
kwh/m2/year and with HVAC optimization 125
kwh/m2/year and finally with Controls, sensors, rain
and waste water harvesting it will reach to 95
kwh/m2/year. All these results will be simulated by
using RETSCREEN software by considering a case
study.
III.
MATHEMATICAL MODELING OF EEB
A Simplified Building Energy model will be
analyzed by considering a room with thermal
parameters. The net heat energy loss (or gain) of a
building can be defined at any moment from the
thermal balance of the building (first law). For example
for the calculation of the thermal load the
instantaneous steady-state thermal balance of a
building is given by
(1)
www.ijera.com
For a building, a state of balance practically
means Qloss = Qgain and therefore the thermal load qH
= 0 shown in “Fig.3”. All building losses are depended
for the temperature difference (ΔΤ=Ti-To) of the
internal (Ti) and the external (To) of the building.
Thus, when, Qloss > Qgain something that usually
happens during the winter period where the
temperature differences ΔΤ are high, then qH > 0, and
so qH expresses the additional thermal load in watts
that the building demands in order to return to its
thermal equilibrium state and in the end specifies the
building’s heating demand in time.[5]
The thermal load of a building, after the
introduction of a Building total Loss Coefficient
(BLC) is given then by:
QH = QLoss – Qgain = BLC × (Ti – To) – Qgain
(2)
Where QH is the thermal load in watt, Ti is the
necessary internal temperature of the building (or even
the design temperature of the building in 0C) and T0 is
the outside temperature.
The BLC is calculated in Watt/0C, modified
to include both the thermal losses through the
buildings envelope and the infiltration losses. For any
building, BLC can be normally calculated as:
(3)
Where UT,I is the thermal conductance in
Watt/(m2 K) of the building components (outside
walls, floors, doors, windows etc., ) Ai is the respective
components areas in m2, minf is the mass flow rate of
infiltration air in kg/sec (Lt/sec), Cpa is the specific heat
capacity of air at constant pressure in KJ/(Kg0K). In the
BLC, they are also considered the relative heat
capacities of the building components within which it
is stored an additional thermal load that might come
either from the heat gains or the heat losses of the
building[6].
379 | P a g e
3. Vijaya Lalita. P et al Int. Journal of Engineering Research and Application
ISSN : 2248-9622, Vol. 3, Issue 6, Nov-Dec 2013, pp.378-381
IV.
CASE STUDY ANALYSIS BY
RETSCREEN
The RETSCREEN Software Building
Envelope Model can be used worldwide to evaluate the
energy use and savings, costs, emission reductions,
financial viability and risk for building envelope
energy efficiency measures. The software can model a
wide variety of projects ranging from passive solar
designs for houses, to energy efficient window use in
commercial buildings, to complete energy efficient
construction practices on the entire building envelope
for large institutional and industrial buildings [7]. The
software also includes product, project and climate
databases, and a detailed user manual.
In this case the analysis is considered for
JNTU College of Engineering Kakinada. For this
analysis the procedure is as follows:
www.ijera.com
show the data of climatic conditions of the considered
location. While the latitude and longitude values are
entered, the values of Air temperature, Relative
humidity, Daily radiation-horizontal, Atmospheric,
wind speed, Earth temperature, Heating Degree days,
Cooling degree days are obtained for monthly basis.
The data obtained is only for reference purpose not to
run the model.
Fig 5: Building parameters
Fig. 3: Energy model sheet of RETSCREEN
The project type is of Energy efficient
Measures, this is of institutional facility type and the
analysis method is considered as method 1. The
Heating value reference is considered as LHV. Higher
heating value is typically used in cold locations like
Canada and USA, while lower heating value is used in
the rest of the world. Hence LHV is selected. This is
of International wide software hence we can get the
currency what we required. The climatic data
conditions are obtained for this location which is
included in Site reference conditions.
In this tool, enter the information about the
facility characteristics, for the base case and the
proposed case facilities. The user clicks on the blue
hyperlinks (e.g. Heating system, Cooling system,
Building envelope, ventilation, lighting etc.) to access
the data entry forms used to describe the facility. In
addition, the key results of the model are displayed in
this section (e.g. fuel saved, simple payback, etc.).
In this analysis the electrical equipments like
fans, tube lights and computer are taken. For these
equipments the base case and proposed case are
considered. By using efficient devices the power
saving is of 36.2%. Although the initial cost may be
high, at last there is a lot of saving. For building
envelope the payback period is 8.3 years and for
electrical equipments there is no payback period
means when we invest the money immediately we can
get the savings.
A. Emission Analysis:
Fig.6: Emission analysis
Fig.4: Climate data base
To access the RETSCREEN Climate
Database click on the "Select climate data location"
hyperlink or use the RETSCREEN menu or toolbar.
This is the extension of first window which
www.ijera.com
Comparing to base case the proposed case
will cut short the emissions to 28%. That is equivalent
to 6 cars not used per year. In a larger scale it can earn
the carbon credits to the project and it will support the
additional revenue to the project.
380 | P a g e
4. Vijaya Lalita. P et al Int. Journal of Engineering Research and Application
ISSN : 2248-9622, Vol. 3, Issue 6, Nov-Dec 2013, pp.378-381
B. Financial analysis:
[4]
[5]
[6]
Fig.7: Financial analysis
In financial analysis, the fuel rate for base
case with proposed cases are compared even though
the initial investment is high the payback period is
very less in some times it may be neglected also. Here
the project life is considered for 30years.
V.
CONCLUSIONS
The results obtained by using RETSCREEN
software can be very realistic and gives very
promising results for Energy Efficient Buildings. The
main feature of this software is; it will integrates the
local climatic conditions and hence planning of energy
models are simpler.
The building simulation results, found that
how various parameters in energy dependence can be
decreased by step by step and finally gives the
reduction in energy needs. However, as the
consideration of equipments was done optimistically
for the desired building load and net profits will be
higher than the results in simulation by considering
carbon credits and subsidies from government
organizations.
VI.
References
[2]
[3]
Xiaoli Li, Chris P. Bowers, and Thorsten
Schnier,
Classification
of
Energy
Consumption in Buildings With Outlier
Detection, IEEE transactions on industrial
electronics, vol. 57, no. 11, November 2010
Liping Wang, Julie Gwilliam, Phil Jones,
Welsh school of Architecture, Cardiff
University, on Case study of zero energy
house design in UK, Elsevier, Energy and
Buildings 41 (2009) 1215–1222
A.J. Marszala,
P. Heiselberg,
J.S.
Bourrelle, E. Musall, K.Vossc, I. Sartori,
A.Napolitano Zero Energy Building – A
review of definitions and calculation
methodologies, Elsevier, Energy and
Buildings 43 (2011) 971–979
www.ijera.com
[8]
[9]
[10]
ACKNOWLEDGEMENTS
I thank the Department of EEE, JNTU
Kakinada for giving the information regarding to
building particulars.
[1]
[7]
[11]
[12]
[13]
www.ijera.com
Guglielmo S. Aglietti,Harnessing HighAltitude Solar Power, IEEE, transactions on
energy conversion, vol. 24, no. 2, june 2009
Mohan Kolhe Techno-Economic Optimum
Sizing of a Stand-Alone Solar Photovoltaic
System, , IEEE TRANSACTIONS ON
ENERGY CONVERSION, VOL. 24, NO. 2,
JUNE 2009
Electricity, Resources, and Building Systems
Integration at the National Renewable Energy
Laboratory, David Mooney National
Renewable Energy Laboratory, Golden,
Colorado
978-1-4244-4241-6/09/
2009
IEEE
Creating Low-Cost Energy-Management
Systems for Homes Using Non-Intrusive
Energy Monitoring Devices, Rebecca L.
Sawyer, Jason M. Anderson, Edward Lane
Foulks, John O. Troxler, and Robert W. Cox
978-1-4244-2893-9/09/ 2009 IEEE
G.R.K.D.Satya Prasad, Dr. K. Vijaya Kumar
Reddy, Dr. CH. Saibabu M.Tech., Ph.D,
Integration of renewable energy sources in
Zero energy buildings with economical and
environmental aspects by using HOMER.
G.R.K.D.Satya Prasad* et al. / (IJAEST) Vol
No. 9, Issue No. 2, 212 – 217
New Technologies for Rural Lighting in
Developing Countries: White leds Adoniya
Ben Sebitosi, Member, IEEE, and Pragasen
Pillay, Fellow, IEEE transactions on energy
conversion, VOL. 23, NO. 1, MARCH 2008
Phatiphat Thounthong, St´ephane Ra¨and
Bernard Davat,Control Algorithm of Fuel
Cell and Batteries for Distributed Generation
System, Member, IEEE transactions on
energy conversion, vol. 23, no. 2, june 2008
Piyasak Poonpun, Student Member, IEEE,
and Ward T. Jewell, Fellow Analysis of the
Cost per Kilowatt Hour to Store Electricity, ,
IEEE transactions on energy conversion, vol.
23, no. 2, june 2008
Chin-Sien Moo, Member, IEEE Parallel
Operation of Battery Power Modules, , Kong
Soon Ng,
Student
Member,
IEEE
transactions on energy conversion, vol. 23,
no. 2, june 2008
Caisheng Wang, Senior Member, IEEE,
Power Management of a Stand-Alone
Wind/Photovoltaic/Fuel Cell Energy System
transactions on energy conversion, vol. 23,
no. 3, september 2008.
381 | P a g e