This document provides a CCNA command cheat sheet covering Cisco IOS commands for the CCNA exam. It includes sections summarizing commands for Cisco device configuration, interface configuration, routing protocols, privilege mode commands, and more. The cheat sheet covers both ICND exam parts 1 and 2 and is intended to help review the majority of commands found on the CCNA exam.
1 of 8
Download to read offline
More Related Content
Cisco Commands
1. Experts in Networking
0870 350 4000 training@ncat.co.uk www.ncat.co.uk
CCNA Cheat Sheet
This CCNA command ‘cheat sheet’ covers both ICND parts 1 & 2 and covers the current
CCNA exam (640-802).
Whilst not an exhaustive IOS command list it covers the majority of commands found in the
exam. Older ‘cheat sheets’ may contain additional commands, such as IPX which is no longer
in the exam.
Cisco Modes
Description Keyboard short cut
User mode Switch>
Enter Privilege mode Switch>enable
Privileged mode Switch#
Enter configuration mode Switch#configure terminal
Global Config mode Switch(config)#
Enter Interface mode Switch(config)#interface fa0/1
Interface mode Switch(config-if)
Return to global
configuration
Switch(config-if)exit
Exit Global Config mode Switch(config)#exit
Return to use mode Switch#disable
Logout Switch>exit
Keyboard Shortcuts
Description Keyboard shortcut
Recall Previous command Up arrow or <Ctrl> p
Recall Next command Down arrow or <Ctrl> n
Beginning of command <Ctrl> a
End of command <Ctrl> e
Delete input <Ctrl> d
Exit Configuration Mode <Ctrl> z
Complete command TAB
2. Experts in Networking
0870 350 4000 training@ncat.co.uk www.ncat.co.uk
Device Configuration
Description Commands
Configure device system
name
Switch(config)#hostname sw1
Sets the encrypted enable
password
Switch(config)#enable secret cisco
Sets the unencrypted enable
password
Switch(config)#enable password cisco
Enable password encryption
on all clear text password
within the configuration file
Switch(config)#service password-encryption
Configure a Message Of The
Banner, with an ending
character of $
Switch(config)#banner motd $
Assign IP address to vlan Switch(config)#int vlan 1
Switch(config-if)#ip addr 172.22.1.11
255.255.255.0
Assign Default gateway, note
the mode
Switch(config)#ip default-gateway 10.1.1.1
Select one interface Switch(config)#int fa0/1
Select a range of interfaces
(version dependant)
Switch(config)#int range fa0/1 – 12
Set the interface description Switch(config-if)#description
Add vlan using config mode switch(config)#vlan 11
switch(config-vlan)#name test
Configure Interface fa0/1 @
speed 100 Mbps and full
duplex
Switch(config-if)#speed 100
Switch(config-if)#duplex full
Assign interface to vlan switch(config-if)#switchport access vlan 11
Enable Port Security. Switch(config-if)#switchport mode access
Switch(config-if)#switchport port-security
Switch(config-if)#switchport port-security
mac-address sticky
Disable Interface Switch(config-if)shutdown
Enable Interface Switch(config-if)no shutdown
3. Experts in Networking
0870 350 4000 training@ncat.co.uk www.ncat.co.uk
Configures 5 Telnet sessions
each with a password of
‘cisco’
Switch(config)#line vty 0 4
Switch(config-line)#login
Switch(config-line)#password cisco
Enable and define console
password of ‘cisco’
Switch(config)#line con 0
Switch(config-line)#login
Switch(config-line)#password cisco
Synchronise console
messages (keep what you
have typing on the screen)
Switch(config-line)#logging synchronous
Set the timezone and
automatically adjust
Switch(config)#clock timezone gmt 0
Switch(config)#clock summer-time gmt
recurring
Sets the switch priority for
the vlan. This combined with
the switch mac address
creates the switch BID
Switch(config)#spanning-tree vlan 1 priority
4096
Enables portfast Switch(config)#int fa0/1
Switch(config-if)#spanning-tree portfast
Enables RSTP. Other
options are, PVST and MST
Switch(config)#spanning-tree mode rapid-pvst
Creates a vlan. Note this
now done in config mode
not vlan database. Also note
the ‘int vlan’ command does
NOT create vlans
Switch(config)#vlan 2
Switch(config-vlan)#name sales
Assign an interface to vlan 2 Switch(config-if)#switchport access vlan 2
Unconditionally forces an
interface into trunking. Other
options are access and
dynamic
Switch(config-if)#switchport mode trunk
Manually assign a switch to
a VTP domain. A switch will
automatically become part of
a VTP domain if it’s currently
in the ‘null’ domain and
receives a VTP frame
Switch(config)#vtp domain lab
Changes the VTP mode from
the default ‘server’ mode to
client mode. In client mode
no changes can be made
Switch(config)#vtp mode client
Enable the http server to
SDM can be used
Router(config)#ip http server
4. Experts in Networking
0870 350 4000 training@ncat.co.uk www.ncat.co.uk
Defines a username and
password. The list can be
used for many things from
PPP authentication to user
access
Router(config)#username sue password cisco
Defines a local host file. Like
/etc/hosts in unix
Router(config)#ip host mypc 10.1.1.3
Disables DNS lookup. Useful
when a command as been
miss typed
Router(config)#no ip domain-lookup
Sets the logical (not
physical) bandwidth of
interface. This is used by
routing protocols, SNMP
queuing etc
Router(config)#int s0
Router(config-if)#bandwidth
Sets the physical clock Router(config-if)#clock rate 64000
Set the serial interface WAN
encapsulation. Other options
are PPP or frame-relay
Router(config-if)#encapsulation hdlc
Authentication on PPP is
optional. This command
enable chap on the interface.
Other option PAP
Router(config-if)#ppp authentication chap
Defines the type of LMI
being used. If left un-
configured the correct LMI
type should be automatically
detected
Router(config-if)#frame-relay lmi-type cisco
Defines a static route.
Renumber static routes have
an admin distance of 1.
Therefore will over ride any
dynamic routing.
Router(config)#ip route 50.0.0.0 255.0.0.0
10.1.2.1
Enables RIP version 1 on all
LOCAL interfaces which
have a 10.x.x.x address
Enables RIP version 2
Router(config)#router rip
Router(config-router)#network 10.0.0.0
Router(config-router)#version 2
Enable the router to provide
a DHCP service.
Router(config)#ip dhcp pool MYPOOL
Router(dhcp-config)#network 10.1.1.0
255.255.255.0
Router(dhcp-config)#default-router 10.1.1.1
Router(dhcp-config)#exit
Router(config)#ip dhcp excluded-address
10.1.1.1 10.1.1.99
Changes the config register
which controls what the
Router(config)#config-register 0x2102
5. Experts in Networking
0870 350 4000 training@ncat.co.uk www.ncat.co.uk
router does when the router
boots
Creates a logical sub
interface below the physical
interface
Enables 802.1q trunking on
the interface
Define the ip address
Router(config)#int fa0/0.1
Router(config-subif)#encapsulation dot1Q 1
Router(config-subif)#ip address 10.1.1.1
255.255.255.0
Enable OSPF on any local
interface which start with the
ip address 10.1.x.x. Note the
inverted mask
Router(config-)#router ospf 1
Router(config-router)#network 10.1.0.0
0.0.255.255 area 0
EIGRP can be configured in
a similar way to RIP or the
mask option could be used
Router(config)#router eigrp 1
Router(config-router)#network 172.16.0.0
Or
Router(config-router)#network 172.16.2.0
0.0.0.255
Defines a standard ACL.
Standard ACL use number
1-99
Router(config)#access-list 1 permit
172.16.1.1
Defines an Extended ACL.
The first address is the
source IP address
Router(config)#access-list 101 deny tcp host
172.16.1.1 host 172.16.2.1 eq telnet
Router(config)#access-list 101 permit ip any
any
Use the group command to
attach an ACL to an
interface.
is used under an interface if
the ACL is to filter traffic
Router(config)#interface fa0/0
Router(config-if)#ip access-group 1 out
An example using named
ACL in stead of numbers
Router(config)#ip access-list extended
my_list
Router(config-ext-nacl)# deny tcp host
172.16.1.1 host 172.16.2.1 eq ftp
Router(config-ext-nacl)# permit ip any any
Attaching a named ACL to
an interface
Router(config)#int fa0/0
Router(config-if)#ip access-group my_list in
Configuring a static NAT to
allow a server to be access
via the Internet, using the IP
address on interface s0/0/1
Router(config)#ip nat inside source static
10.1.1.2 interface s0/0/1
Defining interface which NAT
takes place between
Router(config)#int fa0/0.1
Router(config-if)#ip nat inside
Enables RIPng Router(config)#ipv6 unicast-routing
ROuter(config)#ipv6 router rip ccna
6. Experts in Networking
0870 350 4000 training@ncat.co.uk www.ncat.co.uk
Router(config)#int s0/0/0
Router(config-if)#ipv6 rip ccna enable
Privilege Commands
Description Commands
Manually starts the setup
dialog which is automatically
invoked when the device
starts with no config
Switch#setup
Displays the config held in
DRAM. Which is lost if not
copy run start command is
not used
Switch#show running-config
Displays the NVRAM (None
volatile) config.
Switch#show startup-config
Saves the config. Without
this command all
changes/configuration will be
lost.
Switch#copy running-config startup-config
Saves the running config to a
TFTP server
Switch#copy running-config tftp
Copies IOS files to a TFTP
server
Switch#copy flash tftp
Copies files from a TFTP
server the device flash
Switch#copy tftp flash
Erase the config held in
NVRAM. If this is followed
with the reload command all
configuration is lost
Switch#erase startup-config
Reboots the device Switch#reload
Abort sequence <Shift> <Ctrl> 6
Suspend Telnet Session <Shift> <Ctrl> 6(then let all keys go, then)x
Show the current sessions.
The one with a * is your
active session
Switch#show sessions
Forcible closes a telnet
session
Switch#disconnect
Set the device local clock.
Note this is not done in
config mode
Switch#clock set 10:00:00 april 2 2008
7. Experts in Networking
0870 350 4000 training@ncat.co.uk www.ncat.co.uk
Display the IOS version
along with other useful info
e.g sys uptime, config
register etc
Switch#show version
Displays the file contents of
the flash
Switch#show flash
Displays the clock Switch#show clock
Displays the users currently
logged on
Switch#show users
By default displays the last
10 commands
Switch#show history
Displays the ARP cache Switch#show arp
Displays the spanning tree
status on vlan 1
Switch#show spanning-tree vlan 1
Lists all the configured vlans Switch#show vlan
Displays VTP info such as
VTP mode, VTP domain,
VTP counter.
Switch#sh vtp status
Ping selected address Switch#ping 10.1.1.1
Extended ping. Must be in
privilege mode
Switch#ping
Display the interface status Switch#show int fa0/1
Displays the vlan status and
the IP address VLAN 1
(often the management vlan)
Switch#show interfaces vlan 1
Displays a list of CDP
neighbours
Switch#show cdp neighbors
Extended information on the
above
Switch#show cdp neighbors details
Display CDP packets as they
arrive
Switch#debug cdp packets
Display ping packets as they
arrive
Switch#debug icmp packets
Display switch MAC
Addresses table. These
entries are learnt from the
source mac address in the
Ethernet frames
Switch#show mac address-table
8. Experts in Networking
0870 350 4000 training@ncat.co.uk www.ncat.co.uk
Displays the interface
operational status and IP
addresses for all router
interfaces
Router#show ip interface brief
Displays all the configured
routing protocols
Router#show ip protocols
Displays the IP routeing
table
Router#show ip route
Displays the NAT
translations
Router#show ip nat translations
Displays the physical cable
DTE/DCE, x.21, V.35,
RS232 configuration
Router#show controllers s 0
Displays the end-to-end
status. Recall that ‘show
interface’ does not
Router#show frame-relay pvc
Displays the type of LMI and
the number LMI frames
Router#show frame-relay lmi
Displays the frame relay
inverse ARP table
Router#show frame-relay map
To be come neighbours both
the local and remote
interface must be correctly
configured.
Router#show ip ospf neighbor
If adjacent routers don’t
become neighbours. Then
use the command to check
the local router interface is
configured correctly
Router#show ip ospf interface
Same information as the
above OSPF commands but
with EIGRP. Remember that
AS numbers MUST match
Router#show ip eigrp neighbor
Same information as the
above OSPF commands but
with EIGRP
Router#show ip eigrp interface
IPv6 ping. Recall that ::
means all zero in between
Router#ping 2000:1000:500:3::1