International Journal of Computational Engineering Research(IJCER) is an intentional online Journal in English monthly publishing journal. This Journal publish original research work that contributes significantly to further the scientific knowledge in engineering and Technology.
Report
Share
Report
Share
1 of 7
Download to read offline
More Related Content
D031201025031
1. International Journal of Computational Engineering Research||Vol, 03||Issue, 12||
An Experimental Investigation on Condensation Heat Transfer of
Microchannel Heat Exchangers
Thanhtrung Dang and Minhhung Doan
Department of Heat and Refrigeration Technology, Ho Chi Minh City University of Technical Education, Ho
Chi Minh City, Vietnam
ABSTRACT:
The present study investigated experimentally condensation heat transfer of two microchannel
heat exchangers. The heat transfer rate of a microchannel heat exchanger was achieved 272.9 W for the
vapor having the inlet temperature of 101 ºC and the mass flow rate of 0.123 g/s and for the cooling
water having the inlet temperature of 32ºC and mass flow rate of 3.1133 g/s. It was also observed that
the heat transfer rate obtained from the counter flow arrangement is always higher than that obtained
from the parallel one: the value obtained from the counter flow arrangement is 1.04 to 1.05 times of that
obtained from the parallel flow. The results for two phases are in good agreement with the results for
single phase. In addition, the condensation heat transfer coefficient in the microchannel heat exchangers
decreases as increasing the inlet cooling water temperature.
KEYWORDS: Microchannel, condensation, configuration, heat exchanger, efficiency.
NOMENCLATURE
h
entalpy
kJ/kg
m
mass flow rate kg/s
Q
heat transfer rate W
T
temperature ºC
Subscripts
i
inlet
o
outlet
v
vapor
w
water
Greek symbols
efficiency
I.
INTRODUCTION
The use of microchannel heat exchangers can bring advantages such as enhanced heat transfer
coefficient and decreased characteristic dimension. The use is found in chemical, medical areas and in micro
electro-mechanical systems (MEMs). In relevant studies of microchannel heat transfer, Hu and Chao [1] studied
five condensation flow patterns for water in silicon micro condenser. For a hydraulic diameter of 73 m and the
range of mass fluxes of steam from 5 to 45 kg/(m2s), the heat transfer coefficients obtained were from 220 to
2400 W/(m2K) and the corresponding pressure drops were from 100 to 750 kPa/m. In the study, the maximum
heat flux achieved was 40 kW/m2. The study indicated that cooling capacity and the coefficient of performance
(COP) of the microchannel condenser were higher than those of the conventional condenser under the same
operating condition. In addition, the amount of fluids used in the heat exchanger systems with microchannel
condensers was smaller than that with the conventional one. Two R410A residential air-conditioning systems,
one with a microchannel condenser and the other with a round-tube condenser, were studied by Park and Hrnjak
[2]. The cooling capacity and the coefficient of performance (COP) of the system with the microchannel
condenser were 3.4% and 13.1% higher, respectively, than those obtained with the round condenser. The
amount of working fluids charged for the system with the microchannel condenser was 9.2% smaller than that
with the round-tube condenser. The numerical model also used to calculate for the non-uniform distribution of
the air and refrigerant. The numerical results did not make a significant difference for predicting the condenser
capacity. Numerical model for microchannel condensers and gas coolers was investigated by Martínez-Ballester
et al. [3].
||Issn 2250-3005 ||
||December||2013||
Page 25
2. An Experimental Investigation On Condensation…
The main conclusion of this study is that it is possible to take into account the heat conduction between
tubes in a more fundamental way than other fin efficiency based approaches, which have to apply heat
conduction terms to an approach that uses the adiabatic-fin-tip assumption, which is not satisfied in such cases.
However, this study just indicated in description and validation state only. Cho et al. [4] studied the fabrication
of the micro condenser tube by direct extrusion. The materials used to manufacture for this micro condenser are
A1100 and A3003 aluminum alloy. Because A3003 alloy can be durable when it used in a heat exchanger that
requires high working pressure, so A3003 alloy is more suitable than A1100 alloy for the condenser tube with
eco-friendly refrigerant usage. A comparison of condensation heat transfer and pressure drop of CO 2 in
rectangular microchannels was studied by Heo et al. [5]. The condensation heat transfer coefficients of CO2 in
rectangular microchannels with 7, 23, and 19 ports were experimentally investigated with the variation of the
mass flux. The condensation heat transfer coefficient increased with the decrease in hydraulic diameter, which is
dominant at condensation temperatures of 0 and -5 C. Increasing or decreasing the heat transfer coefficient at
critical vapor quality was observed for the microchannel of 23 ports. The existing models for the prediction of
heat transfer coefficients over-predicted the experimental data and the model of relevant literature showed the
smallest deviation of 47.7%. A study on condensation of compact heat exchanger was done by García-Cascales
et al. [6]. In this study, an iterative algorithm has been suggested for the study of two-row heat exchangers. A
brief state-of-the-art study has been done for condensation in micro- and mini-channels and some remarkable
correlations introduced in the existing literature have been described. They have also been compared under
typical operating conditions. Several heat exchangers working as a condenser or an evaporator have been
studied experimentally and the results obtained have been compared with those provided by the model. Hrnjak
and Litch [7] presented a study of two aluminum condensers: a microchannel condenser (a parallel tube
arrangement between headers and microchannel tubes, having a hydraulic diameter Dh = 0.7 mm) and another
one (with single serpentine macrochannel tube having a hydraulic diameter Dh = 4.06 mm). The ratio between
amount of working fluids charged and capacity of the microchannel condenser was around 76% less than for the
serpentine condenser.
Dang and Teng [8, 9] studied the effects of configurations on performance of the microchannel and
minichannel heat exchangers. Effect of flow arrangement on the heat transfer related behaviors of a
microchannel heat exchanger was presented by Dang and Teng [10]. For all cases done in the study, the heat
flux and performance index obtained from the counter-flow arrangement are always higher than those obtained
from the parallel-flow one: the values obtained from the counter-flow are 1.1 to 1.2 times of those obtained from
the parallel-flow. However, in [8-10] they studied on microchannel heat transfer on single phase. Goss and
Bassoc [11] studied heat transfer during the condensation of R134a inside eight parallel microchannels. The
study indicated that there is no clear influence of the fluid saturation temperature and the heat flux removed on
the heat transfer coefficient for the range tested. On the other hand, the heat transfer coefficient value increases
with rising the mass velocity. It is also demonstrated that the consideration that all of the heat transfer resistance
is due to the heat conduction through the liquid film is a good approximation. The interfacial and disjoining
pressure resistances can be neglected even in the higher quality range. From the above literatures, it is important
to study the efficiency of condensation heat transfer in microchannel heat exchangers. For the present study, two
microchannel heat exchangers with different geometrical configurations will be discussed.
II. METHODOLOGY
The experimental system consists of four major components: the test sections (the microchannel heat
exchangers), pump system, steam boiler, and overall testing loop, as shown in Fig. 1. The vapor produced in the
boiler passes through the micro condenser, where it condenses by the cooling water. Two microchannel heat
exchangers were designed and tested in this study. Figure 2 shows the dimensions of the test sections. The
material for the heat exchangers is aluminum, used as a substrate with thermal conductivity of 237 W/(mK),
density of 2,700 kg/m3, and specific heat at constant pressure of 904 J/(kg K). At each inlet or outlet, a
temperature sensor was set to record temperature values. The inlet and outlet water temperatures were measured
using T-type thermocouples. These thermocouples were inserted into the tubes at the inlets and the outlets. So,
there were total four temperature sensors were used to record data.
||Issn 2250-3005 ||
||December||2013||
Page 26
3. An Experimental Investigation On Condensation…
S4
S1
S3
S2
Saturated vapor
P
Inlet cooling water
Outlet cooling water
Outlet cooling water
Condensing vapor
Saturated
vapor
2
7
Intlet cooling water
Condensing vapor
1
6
4
5
4
3
3
Fig. 1. Schematic of the test loop
1. Microchannel heat exchanger;
2. Electric mini Boiler;
3. Mini pump;
4. Water tank;
5. Condensing vapor valve;
6. Adjusting valve;
7. Buffer tank
3
T
L mm
32
mm
A
8.5
mm
mm
9.5
14
mm
W
A
26.5
mm
Wc
Dc
Cross-sectional view A-A
Fig. 2. Dimensions of the test section
||Issn 2250-3005 ||
||December||2013||
Page 27
4. An Experimental Investigation On Condensation…
Basically, the two microchannel heat exchangers (T1 and T2) have the same dimensions; however, the
substrate thickness of T1 is 1.2 mm while T2 is 1 mm and the channel depth for the cooling water side of T1
channel is 300 m (having hydraulic diameter of 375 µm) while T2 is 180 m (having hydraulic diameter of
265 µm). Geometric parameters of the microchannel heat exchangers are listed in Table 1.
Table 1. Geometric parameters of the microchannel heat exchangers
No.
T1
T2
Dimensions of the channel (m)
Vapor side
Cooling water
side
Wc
Dc
Wc
Dc
500
300
500
300
500
300
500
180
Dimensions of the
substrate (mm)
L
46
46
W
26.5
26.5
T
1.2
1
All channels are connected with a manifold for each inlet or outlet of vapor and cooling water,
respectively. The manifolds have a rectangular shape with the width of 3 mm and the depth of 300 m. Figure 3
shows a photo of the microchannel heat exchanger T1. These test sections of the heat exchangers were
manufactured by precision micromachining [8-10]. Each inlet or outlet of the heat exchangers has crosssectional area of 9 mm2. The four sides of the heat exchanger were thermally insulated by the glass wool with a
thickness of 5 mm. To seal the microchannels, two layers of PMMA (polymethyl methacrylate) are bonded on
the top and bottom sides of the substrate, as indicated in Fig. 3. The physical properties of the PMMA and the
glass wool are listed in Table 2. Accuracies and ranges of testing apparatus are listed in Table 3.
Fig. 3. A photo of the test samples
Table 2. Physical properties of PMMA and glass wool
Material
PMMA
Glass wool
Density
kg/m3
1420
154
Thermal conductivity
W/(mK)
0.19
0.051
Equipments used for the experiments are listed as follows:
[1] Thermocouples, Model PT-100, made by Omega
[2] Mini boiler, Model EMB-S-9, made by ELectromn
[3] Pump, VSP-1200, made by Tokyo Rikakikai
[4] Differential pressure transducer, Model UNIK5000, made by GE Druck
[5] Micro electronic balance, Model TP - 214, made by Denver.
Table 3. Accuracies and ranges of testing apparatuses
Testing apparatus
Thermocouples
Differential pressure transducer
Precision balance
||Issn 2250-3005 ||
Accuracy
0.1 C
0.04% FS
0.0015 g
||December||2013||
Range
0 100 C
0 1 bar
0.0000 210g
Page 28
5. An Experimental Investigation On Condensation…
III. RESULTS AND DISCUSSION
For the experiments carried out in this study, the condensation heat transfer of the heat exchangers is
discussed as follows.
The energy balance equation is calculated by
Qv = Qw
(1)
Or mv(hvi – hvo) = mw(hwo – hwi ) (2)
The heat transfer rate of the heat exchanger, Q, is calculated by
Q = Qw = mw(hwo – hwi )
(3)
where m is mass flow rate (subscripts v and w stand for the vapor side and water side, respectively), hvi, hvo, hwi
and hwo are inlet and outlet enthalpy values of the vapor and cooling water sides, respectively [12].
Experimental data obtained from the microchannel heat exchangers are under the room temperature
condition of 3032C. In order to compare the behaviors of heat transfer between the microchannel heat
exchangers, all experimental conditions for the two heat exchangers were kept the same. The experimental
results for T1 and T2 were recorded by MX 100 recorder; the calculated values were taken by the mean values.
For all cases done in this study, the steam outlet from the mini boiler was the dry saturated vapor having the
absolute pressure of 1.4 bar corresponding with the saturated temperature of 110 ºC. Because of the heat loss
from the outlet of mini boiler to the inlet of microchannel heat exchanger, the inlet temperature of microchannel
heat exchangers for vapor side was kept constantly at 101 ºC.
Table 3. Experimental results were recorded by MX100 recorder
a) for microchannel heat exchanger T1
Channel
CH00001[C]
CH00002[C]
CH00003[C]
CH00004[C]
Start Data No. End Data No.
0
0
0
0
661
661
661
661
Min.
Max.
P-P
Mean
RMS
100.7
71.3
52.3
31.7
101.3
73.0
54.1
32.7
0.6
1.7
0.8
1.0
101.0
72.2
52.7
32.1
101.0
72.2
52.7
32.1
b) for microchannel heat exchanger T2
Channel
CH00001[C]
CH00002[C]
CH00003[C]
CH00004[C]
Start Data No. End Data No.
0
0
0
0
406
406
406
406
Min.
Max.
P-P
Mean
RMS
98.7
38.7
39.7
31.6
102.7
40.0
40.9
32.1
4.0
1.3
1.2
0.5
101.0
39.3
40.2
31.9
101.0
39.3
40.2
31.9
In Table 3, the channel CH00001 is the saturated vapor temperature, the channel CH00002 is the
condensing vapor temperature, the channel CH00003 is the outlet cooling water temperature, and the channel
CH00004 is the inlet cooling water temperature. The results in Table 3 recorded for the cooling water having the
inlet temperature of 32ºC and mass flow rate of 3.1133 g/s and for the vapor having the inlet temperature of 101
ºC. The results shown that the outlet temperatures for both vapor and water obtained from T1 are higher than
those obtained from T2. As a result, the heat transfer rate obtained from the heat exchanger T1 (272.9 W) is
higher than that obtained from the heat exchanger T2 (104.6 W). The heat transfer rate of two heat exchangers
was calculated and shown in Table 4. The Table 4 shows that the mass flow rate of condensing vapor decreases
as reducing the hydraulic diameter of channels.
||Issn 2250-3005 ||
||December||2013||
Page 29
6. An Experimental Investigation On Condensation…
Table 4. Heat transfer rate for two models
Model
T1
T2
mv
g/s
0.123
0.0481
mw
g/s
3.1133
3.1133
hvi
kJ/kg
2677.64
2677.64
hvo
kJ/kg
306.388
164.64
hwi
kJ/kg
134.14
134.14
hwo
kJ/kg
221.8
167.7
Q
W
272.9
104.6
In this study, effect of flow arrangement on the heat transfer phenomena of the heat exchangers was
also investigated. For the case done in this study, the two models had the same conditions: the temperature of
saturated vapor was 101C and the temperature of cooling water was 32 C with mass flow rate of 3.159 g/s.
Both heat exchangers were tested in the horizontal position. It was observed that the heat transfer rate obtained
from the counter flow arrangement is always higher than that obtained from the parallel one: the value obtained
from the counter flow arrangement is 1.04 to 1.05 times of that obtained from the parallel flow. The results for
two phases are in good agreement with the results for single phase [10]; however, it is shown that the effect of
flow arrangement in two phases is not stronger than single phase, as shown in Table 5.
Table 5. Heat transfer rate with counter flow and parallel flow arrangements
Model
T1
T2
mv
g/s
0.123
0.0481
mw
g/s
3.159
3.159
Heat transfer rate Q, W
Counter flow
Parallel flow
194,63
184,32
111.52
107.197
Figure 4 shows effect of the inlet cooling water temperature to the outlet temperatures of vapor and water
for the microchannel heat exchanger T1. It is observed to see that when the inlet cooling water temperature
increases, the outlet cooling water temperature increases; however, the temperature difference of cooling water
is increasing slowly. As a result, the temperature difference of vapor side decreases or the condensing vapor
temperature increases. It means that the condensation heat transfer efficiency in the microchannel heat
exchangers decreases as increasing the inlet cooling water temperature, as shown in Fig.4.
68
Temperature, oC
58
48
Condensing vapor
Outlet water
38
Water temperature difference
28
18
29.8
30
30.2
30.4
30.6
30.8
Inlet water temperature, oC
Fig. 4. Effect of the inlet cooling water temperature for heat exchanger T1
||Issn 2250-3005 ||
||December||2013||
Page 30
7. An Experimental Investigation On Condensation…
IV. CONCLUSION
Experimental work was done for the two microchannel heat exchangers with rectangular channels
having hydraulic diameters of 375 µm and 265 µm to investigate condensation heat transfer. For the
microchannel heat exchanger T1, the heat transfer rate of 272.9 W was achieved for the vapor having the inlet
temperature of 101 ºC and the mass flow rate of 0.123 g/s and for the cooling water having the inlet temperature
of 32ºC and mass flow rate of 3.1133 g/s. In this study the heat transfer rate obtained from the counter flow
arrangement is always higher than that obtained from the parallel one: the value obtained from the counter flow
arrangement is 1.04 to 1.05 times of that obtained from the parallel flow. The results for two phases are in good
agreement with the results for single phase; however, it is shown that the effect of flow arrangement in two
phases is not stronger than single phase. In addition, the condensation heat transfer efficiency of the
microchannel heat exchanger decreases as increasing the inlet cooling water temperature.
ACKNOWLEDGMENT
The supports of this work by (1) the project (Project No. T2013-22TĐ /KHCN-GV) sponsored by the
specific research fields at Hochiminh City University of Technical Education, Vietnam and (2) the project
(Project No. 65-13/CTHT-NEPTECH) sponsored by New Product & Technology Center (NEPTECH) –
Hochiminh City Department of Science and Technology of Vietnam, are deeply appreciated.
REFERENCES
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
J.S. Hu and C.Y.H. Chao, An experimental study of the fluid flow and heat transfer characteristics in micro-condensers with
slug-bubbly flow, International Journal of Refrigeration, Vol. 30, (2007), pp. 1309-1318
C.Y. Park and P. Hrnjak, Experimental and numerical study on microchannel and round-tube condensers in a R410A residential
air-conditioning system, International Journal of Refrigeration, Vol. 31, (2008), pp. 822-831
Santiago Martínez-Ballester, José-M. Corberán, José Gonzálvez-Maciá, Numerical model for microchannel condensers and gas
coolers: Part I e Model description and validation, International Journal of Refrigeration, Vol. 36, 2013, pp. 173-190
H. Cho, D.Y. Hwang, B.S. Lee, and H.H Jo, Fabrication of micro condenser tube through direct extrusion, Journal of Materials
Processing Technology, Vol. 187-188, (2007), pp. 645-648
Jaehyeok Heo, Hanvit Park, and Rin Yun, Comparison of condensation heat transfer and pressure drop of CO2 in rectangular
microchannels, International Journal of Heat and Mass Transfer, Vol. 65, (2013), pp. 719–726
J.R. García-Cascales, F. Vera-García, J. Gonzálvez-Macía, J.M. Corberán-Salvador, M.W. Johnson, and G.T. Kohler, Compact
heat exchangers modeling: Condensation, International Journal of Refrigeration, Vol. 33, 2010, pp. 135-147
P. Hrnjak and A.D. Litch, Microchannel heat exchangers for charge minimization in air-cooled ammonia condensers and chillers,
International Journal of Refrigeration, Vol. 31, (2008), pp. 658-668
T.T. Dang and J.T. Teng, Comparison on the heat transfer and pressure drop of the microchannel and minichannel heat
exchangers, Heat and Mass Transfer, Vol, 47, 2011, pp. 1311-1322
T.T. Dang and J.T. Teng, The effects of configurations on the performance of microchannel counter-flow heat exchangers – An
experimental study, Applied Thermal Engineering, Vol. 31, Issue 17-18, 2011, pp. 3946-3955.
T.T. Dang and J.T Teng, Influence of flow arrangement on the performance index for an aluminium microchannel heat
exchanger, IAENG Transactions on Engineering Technologies Volume 5, the American Institute of Physics (AIP), Vol. 1285,
2010, pp. 576-590
G. Goss Jr. and J.C. Passos, Heat transfer during the condensation of R134a inside eight parallel microchannels, International
Journal of Heat and Mass Transfer, Vol. 59, pp. 2013, pp. 9–19
Michael J. Moran, Howard N. Shapiro, Fundamentals of Engineering Thermodynamics, John Wiley & Sons Ltd, England, 2006.
||Issn 2250-3005 ||
||December||2013||
Page 31