1. Careful geological studies are important for selecting dam and reservoir sites to reduce costs and ensure safety and stability.
2. Ideal dam sites have narrow river valleys, competent bedrock like igneous or metamorphic rock near the surface, and favorable geological structures like horizontal or mildly tilted strata.
3. Faults and steeply dipping or folded strata are less desirable as they can compromise the stability and impermeability of the foundation rocks.
2. Syllabus
• Geology of dam sites, reservoirs, roads,
bridge sites and tunnels (broad out lines),
Stability of hills slopes, landslides, their
causes and precautions against them.
3. Geology of Dam Sites
• The Success of a dam is not only related to its own
safety and stability but also to the success of
associated reservoirs. In other words, on
construction, if a dam stands firmly but if its
reservoirs leaks freely then such a dam is to be
treated only as a failure because the purpose for
which it was constructed was not served.
5. Geology of Dam Sites
• Therefore, utmost care is needed in planning for the
success of both the dams and the reservoir.
• Careful geological studies bring out the inherent
advantage or disadvantage of a site and such
studies go a long way either in reducing or in
increasing the cost of a dam considerably.
7. Geology of Dam Sites
• The Important Geological requirements
which should be considered in the selection of
a dam are as follows:
• Narrow River Valleys
• Occurrence of the bedrock at a shallow
depth.
• Competent rocks to offer a stable
foundation
• Proper Geological Structures
8. Geology of Dam Sites
Narrow River Valley
• At the proposed dam site, if the river valley is
narrow, only a small dam is required, which
means the cost of dam construction will be
less. On the other hand, if the valley is wide,
a bigger dam is necessary which means the
construction cost will be very high.
10. Geology of Dam Sites
• Therefore, it is preferable from the economy point
of view, to select such a site along the river valley
which has the least areal cross-section (i.e.. the
narrowest part of the river).
• But such sites should not be blindly selected
without further investigations, because sometimes
they may have severe defects which may lead to
serious leakage from the reservoir and may affect
the safety of the dam.
11. Geology of Dam Sites
Bedrock at Shallow Depths
• To ensure its safety and stability a dam has to
necessarily rest on (Physically) very strong and
(Structurally) very stable (i.e. bedrocks). If such
competent bedrocks occur near the surface or at
shallow depths, the foundation cost of the dam will
naturally be less. On the other hand, if competent
bedrocks occur at great depths, the cost of the
foundation will be very high because it involves
extensive work of excavation of loose overburden
and concrete refilling.
13. Geology of Dam Sites
• The Thickness of sediments or loose overburden along the
river valley depends on the nature and the stage of
development of the river. In other words, strong and fresh
bedrocks may occur at or near the surface, therefore only
small dams may be suitable.
• The general occurrence of material like clay, silt, sand and
gravel along the river bed, naturally makes it difficult to
assess the thickness of loose overburden by simple surfacial
studies. Therefore to know the bedrock profile, geophysical
investigations such as “Electrical Resistivity studies” or
“Seismic refraction Studies” are carried out carefully. The
data recorded in the field during investigations are
interpreted and the required bedrock profile is visualized.
15. Geology of Dam Sites
Competent Rocks for Safe Foundation:
• If Igneous rock occurs at the selected dam site,
they will offer a safe basis, and weak sedimentary
rocks, particularly shale's, poorly cemented
sandstones and limestone's shall naturally be
undesirable to serve as foundation rocks.
17. Geology of Dam Sites
• The suitability or otherwise of a site to serve as a
foundation for major dams depends on factors such as
:
• The existing rock type at the dam site.
• The extent of weathering it has undergone
• The occurrence of intrusions
• The extent of fracturing
• The extent of geological structures, the mode and
number of rock types concerned.
18. Geology of Dam Sites
Suitability of Igneous Rocks
• Among the rock types, the occurrence of massive plutonic
and (or) hyperbyssal igneous rocks is the most desirable at
the dam site because they are very strong and durable due
to their dense character. Interlocking texture, hard silicate
mineral composition, occurrence of negligible porosity and
permeability, absence of any inherent weak planes,
resistance of weathering and their tendency to occur over
wide areas. Thus all plutonic rocks like Granites, Syenites,
diorites and gabbros are very competent and desirable
rocks.
• However, volcanic rocks which are vesicular or
amygdaloidal, are not equally desirable, obviously because
these character contributes to porosity, permeability and
hollowness which, in turn, reflect the strength of the rocks.
19. Geology of Dam Sites
• Of Course, it is necessary that such rocks should not
have been affected by any intense weathering or
fracture or dykes or adverse geological structures like
shearing, faulting and jointing.
20. Geology of Dam Sites
Suitability of Sedimentary Rocks
• In this case of sedimentary rocks, the bedding and
its orientation, thickness of beds, nature and extent
of compaction and cementation, grain size,
leaching of soluble matter, porosity and
permeability, associated geological structures and
composition of constituents (i.e. Sediments,
cementing material, etc.) influence the strength and
durability of different sedimentation rocks.
22. Geology of Dam Sites
• Based on above-mentioned details, it may be stated that:
• Shales are not naturally useless but they also form slippery
bases. The fore they are most undesirable at dam sites.
• Among Sandstone, well-cemented siliceous type are
competent and suitable for the dam construction.
• Laterites and conglomerates are undesirable at dam sites
• Limestones are competent if they are massive, i.e..
unaffected by the solution phenomenon, Hence they are
undesirable at dam sites.
24. Geology of Dam Sites
Limestone
Laterite
Sandstone
Conglomerate
25. Geology of Dam Sites
Suitability of Metamorphic Rocks
• Among the metamorphic rocks:
• “Gneisses” are generally competent like granites, unless
they possess a very high degree of foliations and are richly
accompanied by mica-like minerals.
• Quartzites are very hard and highly resistant to
weathering. They are neither porous nor permeable.
• Marbles, like quartzite, are compact, bear a granulose
structure, are not porous, nor permeable and reasonably
strong too. But by virtue of their chemical composition
and minerals they are unsuitable at dam sites.
• Slates bear a typical slaty cleavage. Hence this rock is soft
and weak and undesirable at dam sites.
27. Geology of Dam Sites
• After learning the suitability of the occurrence of different
varieties of common rocks at dam sites, it should be
remembered that all types of rocks exhibit within
themselves some variations in their chemical and mineral
composition.
• Finally it may be said that most of the igneous and
metamorphic rocks, when fresh and free from structural
defects, have enough strength to bear the loads involved in
dam of all sizes with surplus safety factor too.
29. Geology of Dam Sites
Effects of Associated Geological Structures
• For the stability of a dam, the occurrence of
favorable geological structure is a very important
requirement. Under structural geology we have
learnt that those rocks bear certain inherent or
original physical properties, such characters get
modified either advantageously or
disadvantageously when geological structure
occurs in those rocks.
32. Geology of Dam Sites
Cases of Undisturbed i.e. Horizontal Strata
• This geological situation is good at the dam site because
the load of the dam acts perpendicular to the bedding
planes, which means that the beds are in an profitable
position to bear the loads with full capability.
• Further, the seepage of reservoir water that may take place
beneath the dam is effectively prevented by the weight of
the dam which acts vertically downwards.
33. Geology of Dam Sites
• Cases where Beds lie Perpendicular to the length
of the valleys
• (a) Tilted Beds
• Beds with 10 0 to 30 0 inclination in the upstream
directions
• Such a situation is ideal because the resultant
force acts more or less perpendicular to the
bedding plane which are dipping in the upstream
side.
35. Geology of Dam Sites
Beds with Steep Downstream Dip
• For obvious reasons this situations has all
the disadvantages of the previous case.
Further, here the resultant force and
bedding planes are nearly parallel, which
means that the beds will be even less
competent.
36. Geology of Dam Sites
Beds which are Folded
• Folding of beds, which occurs on a relatively large
scale, is generally less dangerous than faulting. Unless
the folds are of a complex nature.
• However, it should be borne in mind that unlike
simply tilted strata, the folded rocks are not only under
strain but also physically fractured along the crests.
Hence grouting & other precautions may have to be
considered, depending on the context, to improve the
stability and competence of rocks at the site.
38. Geology of Dam Sites
Beds Which are Faulted
• Occurrence of faulting irrespective of its attitude (i.e..
Strike and Dip), right at the dam site is most undesirable. If
the faults are active, under no circumstances, can dam
construction be taken up there. This is not only because
of the fear of possible relative displacement of the site itself
but also due to the possible occurrence of earthquakes.
• Further, if the fault zone is crushed or intensely
fractured, it becomes physically incompetent to
withstand the forces of the dam.
• Thus locations of the dam sites on a fault zone is
undesirable for different reasons.
40. Geology of Dam Sites
Beds Which Have Joints
• Among the different geological structures, joints are
the most common and are found to occur in all kinds
of rocks, almost everywhere.
• But Since the rocks with these joints are not under any
strain, and also because of the scope to overcome their
effects easily by simple treatment, they are not
considered as serious defects. Grouting is generally
capable of overcoming the adverse effects of joints
because it fill the gaps of joints, increase compactness
and competency of the rocks & reduce porosity &
permeability.
43. Reservoir
• From the Geological point of view, a reservoir
can be claimed to be successful if it is watertight
(i.e.. if it does not suffer from any serious
leakage of water) and if it has a long life due to
very slow rate of silting in the reservoir basin.
The reservoir, when filled, gives chances for
reactivation of underlying inactive faults. This
in turn, gives scope for the occurrence of
seismicity and landslides in that region.
45. Reservoir
Capacity of the Reservoir
Effect of Evaporation
• The natural process of evaporation reduces the
quantity of water in the reservoir. Through unwanted,
this process is unavoidable. Since reservoirs are open
and extended over larger areas. The magnitude of
evaporation will be extensive. Of course, such loss
shall be less if the topography is such that a reservoir
covers a small area but has a great depth to provide
adequate capacity.
47. Reservoir
Water- Tightness and Influencing factors
• When a river flows over such loose soil or
fractured ground, it is natural that some water of
the river percolates (or leaks) underground. Before
the construction of the dam, this leakage shall be less
and limited only to the extent over which the river
flow occurs. But when the dam is constructed, the
impounding water accumulates in large quantity in a
reservoir which covers a very large area.
48. Reservoir
• Further, due to the considerable height of the water in
the reservoir, significant hydrostatic pressure
develops which will make the leakage more effective
on the sides and the floor of the reservoir. Thus, the
extent of leakage may become alarmingly great.
49. Reservoir
Influence of Rock Types
• Water-tightness of a reservoir basin is also
very much influenced by the kind of rocks that
occur at the reservoir site. If the rock are
porous and permeable, they will cause the
leakage of water and hence such rock are
undesirable at the reservoir site.
50. Reservoir
Igneous Rocks:
• Intrusive igneous rocks like granite, by virtue of
their composition, texture and mode of
formation are neither porous nor permeable.
Hence their occurs at the reservoir site will not
cause leakage of water unless they have other
defects like joints, faults, or shear zones.
• But the extrusive (i.e.. Volcanic) igneous rocks
like basalt are not desirable because they are
often vesicular.
51. Reservoir
• By virtue of their wide areal extent and frequency of
occurrence, sedimentary rocks are the more important
in this regard than igneous rocks. Among the different
sedimentary rocks shale's are the most abundant
followed by sandstone & limestone.
• Shales the extremely fine grained sedimentary
rocks. Are highly porous but not permeable. For this
reason, the occurrence of shale's at the reservoir site
shall not cause any leakage. Of course, at the dam
site, its occurrence is considered undesirable
because of its incompetency and slippery character.
53. Reservoir
Sedimentary Rocks
• The next common sedimentary rock i.e.. sandstone
is an aquifer and hence it has a tendency to cause
leakage. However, careful examination is needed to
know whether it causes severe leakage or not, if
present at the reservoir site. This is so because the
porosity and permeability of different sandstone
differ depending on a degree of cementation and
composition of the cementing materials of
sandstones.
55. Reservoir
• The Occurrence of limestone, the third most
common rock of the sedimentary group at
the reservoir site is, in general, undesirable.
Of course, it may not only have negligible
porosity but also possess reasonable hardness
and durability. Thus through the compact of
massive limestone superficially seem to be
water proof, they may be internally
cavernous and cause profuse leakage.
57. Reservoir
Metamorphic Rocks
• Gneisses, which are one of the most common
metamorphic rocks, behave like granite, i.e.. they
are neither porous nor permeable. The schists, on the
other hand, by virtue of their excellent foliation
and soft and cleavage-bearing mineral content and
a source of weakness and leakage problems. The
quartzite which are compact, by virtue of their quartz
content and granulose structure, are neither porous
nor permeable.
59. Metamorphic Rocks
• Therefore, their occurrence at reservoir sites
contribute to water-tightness. Marbles, through
compact, by virtue of their calcium carbonate
composition and calcite content are not reliable in
terms of their water tightness. Slates due to their
characteristics slaty due to their characteristic
slaty cleavage may tend to cause leakage but their
very fine grained nature helps in checking such
leakage considerably.
62. Tunnels
• Tunnels are underground passages or routes (or
passages through hills or mountains) used for different
purposes. They are made by excavation of rocks
below the surface or through the hills or mountains.
• Like dams, bridges and reservoirs, tunnels are also
very important civil engineering projects, but with
some differences.
• Unlike other civil engineering constructions which
lie on the surface, generally, tunnels lie underground
(i.e.. within the rocks). For this reason, the needs for
their safety and stability is much more important.
64. Tunnels
Effects Of Tunneling On The Ground
• The tunneling process deteriorates the physical
conditions of the ground. This happens because due
to heavy and repeated blasting excavation, the rocks
gets shattered to great extent and develop
numerous cracks and fractures. This reduces the
cohesiveness and compactness of rocks. In other
words, rocks becomes loose and more fractured
and porous. This naturally adversely affects the
competence of the rocks concerned.
66. Tunnels
Geological Considerations for successful Tunneling
• As already stated, the safety success and economy
of tunneling depend on the various geological
conditions prevailing at the site. As usual, the
important geological factors which interfere with this
civil engineering project (i.e. tunneling) are also
lithological, structural and ground water
conditions.
68. Tunnels
Importance of Rock Types
• Since tunnels through underground rock masses,
obviously the nature of rock types which are encountered
along the tunnel alignment is very important for the
safety and stability of the tunnel.
• In brief, the competent rocks (i.e. those which are strong,
hard and massive) will lead to safe but slow tunneling
and incompetent rocks (which are loose or soft or
fractured), through amenable for easy tunneling, will be
unstable and hence require lining. Of Course, if tunnel
extends for considerably long distances, the kind or
rocks en route may vary from place to place, i.e.
Competent at some places and incompetent at some
other places.
70. Tunnels
Suitability of Igneous Rocks at the Tunnel Site
• Massive igneous rocks, I.e. the plutonic and hyperbyssal
varieties, are very competent but difficult to work. They
do not need any lining or any special maintenance. This is
so because they are very strong, tough, hard, rigid, durable,
impervious and tunneling, do not give way to collapse,
floor bumps, side bulges or to any other deformation.
• The volcanic rocks, too in spite of their vesicular or
amygdaloidal character are competent and suitable for
tunneling. Further, by virtue of frequently present
vesicular or amygdaloidal structure, they are more
easily workable than intrusive rocks.
72. Tunnels
Sedimentary Rocks at the tunnel Site
• In general, sedimentary rocks are less capable than
igneous rocks. Among the different sedimentary rocks.
• Thick bedded, well-cemented and siliceous or
ferruginous sandstones are more competent and better
suited for tunneling. They will be strong, easily workable
and, moreover, do not require any lining. Thus they possess
all the desirable qualities for tunneling, provided they
are not affected adversely by any geological structures
and ground water conditions.
• Shales, by virtue of their inherent weakness and
lamination, may get badly shattered during blasting. But
being soft, they can be easily excavated and hence tunneling
progresses faster through shale formations. Proper lining is
necessary for tunnels built in Shales.
74. Tunnels
• Among limestones, dolomitic limestone are harder
and more durable. They are better than other
varieties. On the other hand, calcareous limestones
or porous limestones are naturally weaker and
softer.
• In a majority of the cases, sedimentary rocks. Being
relatively softer, enables fast progress of work, but
by virtue of their weakness requires suitable
lining.
76. Tunnels
Metamorphic Rocks at the Tunnel Site
• Among different metamorphic rocks, gneisses are
nearly similar to granites in terms of their
competence, durability and workability. Hence, they
are capable of withstanding the tunneling process
without requiring any lining. The gneissose structure
may be advantageous in the excavation process.
Schists, phyllites, etc, which are highly foliated and
generally soft, are easily workable but necessarily
require good lining.
• Quartzite are very hard and hence very difficult to
work they are more brittle too. They are competent
and need no lining.
78. Tunnels
Importance of Geological Structures
• Effects of Joints at the Tunnel Site
• Most of the rocks in nature possess irregular
cracks and regular joints, which are plane
of complete separation in rock masses, and
clearly represent weakness in them. There
will be more qualitively and quantitavely
nearer the surface but generally disappear
with depth.
79. Tunnels
• Closely spaced joints in all kind of rocks are harmful.
However, in general, in igneous rocks, which are
exceptionally strong, the presence may not harm their self-
supporting character.
• In Sedimentary rocks, the occurrence of joints is
undesirable because these rocks, which are originally weak
and incompetent, become still more weak. As in the case of
other rocks, the presence of joints in these rocks also depends
on the past tectonic history of the concerned region.
81. Tunnels
• In Metamorphic rocks also, joints are not characteristic,
but are frequently present. Granite gneisses and quartzites,
being very competent, can remain suitable for tunneling
even if some joints occur in them. But schists and slates with
joints will become very incompetent and necessarily
requires lining.
• Marbles, which possess joints, are unsuitable for tunneling
because, in them, joints are root causes for the occurrence of
sink holes, solution cavities and channels.
• Further, as common with other types of rocks, the sheet
joints occur in this group of rocks too.
84. Tunnels
Fault At The Tunnel Site
• As in other civil engineering projects, in tunnels too,
faults are harmful and undesirable because they
create a variety of problems.
• The active fault are places where there is scope for
further recurrence of faulting, which will be
accompanied by the physical displacement of litho
units. Hence, such faults lead to dislocation and
discontinuity in the tunnel alignment. Therefore,
irrespective of the relation of the attitude of the fault
with the tunnel courses, the occurrence of any active
faults in tunnels is very undesirable.
86. Fault At The Tunnel Site
• The fault zones even if inactive, are places of
intense fracturing, which means that they are zones
of great physical weakness.
• Such a remedial measures of lining (with concrete)
also becomes necessary fault zones, being highly
porous, permeable and decomposed, are the
potential zones to create ground water problems.
88. Tunnels
Folds at the Tunnel Site
• Folds represent the deformation of rocks under the
influence of tectonic forces. Hence the folded rocks will
be under considerable strain. When excavations for
tunnels are made in folded rocks, such rocks get the
opportunity to release this strain (i.e. stored energy). Such
a release may occur in the form of rock bursts or rock
falls or bulging of the sides or the floor or the roof.
Thus complications of such a kind are likely to occur
when tunneling is made in folded regions.
• In folded regions, the tunnel alignment may be parallel
or perpendicular or oblique to the axis of folds. Further
the tunnel may run along the crests or troughs or limbs.
90. Tunnels
• Effects of Undisturbed or Tilted Strata at The Tunnel
Site
Horizontal Beds
• In cases of horizontal or gently inclined beds,
conditions will be favorable for tunneling. But it is
desirable that the bed concerned be thick so that the
tunnel passes through the same formation. This is
preferable because thicker formation are more
competent and hence tunnels through them will be
safe and stable.
91. Tunnels
Inclined Beds
• The forgoing advantage also occur when the
tunnels are made parallel to the strike of massive,
thick, inclined beds or when inclined tunnels are
made following the directions of the slope.
92. Tunnels
• i.e. Parallel to the dip
• In the latter case, an inclined tunnel driven along
the dip of beds must run through the same bed or
beds all along its course. The stability of the tunnel in
all these cases depends on the nature of the beds which
forms the roof. It is relevant to say in this context
that the dip and strike galleries in coal mines are
driven in this way, i.e. along the true dip and strike,
respectively, of the coal seams. These tunnels,
therefore, always run along the coal seams and have
nearly similar conditions all along their length.
93. Tunnels
• However, when the tunnel is horizontal and runs
parallel to the dip direction, then numerous beds
will appear along its course. This is undesirable
because in such a case the tunneling conditions differ
from place to place and this may lead to problems
like stability and over break.