This document discusses key considerations for designing a water distribution system including:
1) The type of water flow (continuous or intermittent) and method of distribution (gravity or pumping).
2) Estimating future demand based on population growth and industrial/firefighting needs.
3) Factors that influence pipe sizing such as hydraulic gradient, flow velocity, and design life.
4) Common pipe joint types like butt-welded, socket-welded, threaded, grooved, flanged, and compression joints and their relative costs, strengths, and installation complexity.
2. Type of flow- whether continuous or intermittent.
Method of distribution- whether by gravity or by
pumping.
Probable future demand based on increase in
population. This also includes the industrial demand as
well as fire –fighting requirements.
Period to be considered in with life of pipes used. The
system should be designed anticipating the future of the
town or city.
4. Hydraulic Gradient: A line joining the points of highest elevation
of water in a series of vertical pipes rising from a pipeline in which
water flows under pressure.
According to HAZEN- WILLIAMS the flow-formula is written as:
V=velocity of flow in pipe m/sec.
M= radius of the pipe in m.
I= Hydraulic gradient.
C=friction coefficient whose valve depends on type of
pipe used.
6. a) Prepare a contoured plan of the city or town, locating the positions of
districts or distribution zones with their population, service reservoirs,
pumping stations, main roads and streets and other small features. A
small scale (1/10,000) may be used.
b)Estimating the rate of demand for all purposes including fire
demand and determining the quantity flowing in each section of
pipe lenght. This gives the average daily flow in the pipe. The
max flow will be 3 times.
c) Assuming the pipe sizes, The velocity of flow varies 0.9-1.2
m/sec.
8. A point at which parts of an artificial structure are
joined.
Types:
1. Butt-welded Joints
2. Socket-welded Joints
3. Threaded or
Screwed Joints
4. Grooved Joints
5. Flanged Joints
6. Compression Joints
9. Butt-welding is the most common
method of joining piping used
in large commercial, institutional,
and industrial piping systems.
Material costs are low, but labor costs are moderate to high due
to the need for specialized welders and fitters.
10. Socket-welded construction is a good
choice wherever the benefits of high
leakage integrity and great structural
strength are important design considerations.
Construction costs are somewhat lower than with butt-welded joints due
to the lack of exacting fit-up requirements and elimination of special
machining for butt weld end preparation.
11. Threaded or screwed piping is commonly used in low-cost,
noncritical applications
such as domestic water, fire protection, and industrial cooling
water systems.
Installation productivity is moderately high, and specialized
installation skill requirements
are not extensive.
Rapid temperature changes may
lead to leaks due to differential thermal expansion between
the pipe and fittings.
13. The main advantages of the grooved joints are their ease
of assembly, which results
in low labor cost, and generally good leakage integrity.
They allow a moderate
amount of axial movement due to thermal expansion, and
they can accommodate
some axial misalignment.
The grooved construction prevents the joint from
separating under pressure.
15. Flanged connections are used extensively in modern
piping systems due to their ease of assembly and
disassembly; however, they are costly.
Contributing to the high cost are the material costs
of the flanges themselves and the labor costs for
attaching the flanges to the pipe and then bolting the
flanges to each other.
Flanges are normally attached to the pipe by
threading or welding, although in some special
cases a flange-type joint known as a lap joint may be
made by forging and machining
the pipe end.
17. Compression sleeve-type joints are used to join plain
end pipe without special end
preparations.
These joints require very little installation labor and as
such result
in an economical overall installation. Advantages
include the ability to absorb a
limited amount of thermal expansion and angular
misalignment and the ability to
join dissimilar piping materials, even if their outside
diameters are slightly different.