This document discusses applications of products from the Jatropha plant. It focuses on using Jatropha oil as fuel in various ways. The oil can be used directly in lamps and cooking stoves with some modifications to account for its higher viscosity than petroleum. It can also be used directly as fuel in diesel engines if the engine is properly converted. Finally, the document discusses producing biodiesel from Jatropha oil, which allows it to be used similarly to conventional diesel fuel once processed. The document also briefly mentions using byproducts from oil extraction for other purposes.
1 of 52
Download to read offline
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
More Related Content
Applications Of Jatropha Products
1. 5 APPLICATIONS OF JATROPHA PRODUCTS
Authors: Peter Beerens, Niels Ansø, Titus Galema, Thijs Adriaans, Janske van Eijck
5.1 Introduction
Jatropha has many potential applications. However, until now only a few have been realised
on a reasonable and large scale. Jatropha is primarily cultivated for its oil. However, this oil is
not the only usable product from the plant. During the process of extracting the oil, many
useful by‐products are created, as well. Here, first the oil applications are discussed, followed
by the applications for the by‐products.
5.2 Applications of oil
Jathropa oil can be used in several ways. The pure (untreated) oil can be used as fuel or for
soap production. Jathropa oil can also serve as a resource for the production of biodiesel.
First the applications of the raw oil are discussed, followed by the oil refining to biodiesel.
5.2.1 Lamps and cooking stoves
Author: Peter Beerens
For lamps and stoves, the conventional fuels in most rural areas are fuel wood, charcoal and
petroleum. By introducing alternatives like plant oils such as jatropha oil for cooking and
lighting, the use of conventional fuels could be strongly reduced. Potential users of the
jatropha oil are those people who currently buy their fuel (charcoal, kerosene) in areas where
there is no free alternative (fuel wood) available.
5.2.1.1 Lamps
The difficulty when using jatropha oil for lighting is its high viscosity. Most kerosene lamps use
wicks. The suction of the Jatropha oil is sufficient in the beginning, but as the oil level
diminishes and the oil has to travel longer distances through the wick, the lamps dim. A second
problem is the formation of cokes on the wick’s surface, which is a second cause for the lamp
to dim. Lastly the ignition temperature of jatropha oil (240°C) is much higher than for
petroleum (84°C). This makes it more difficult to ignite the fuel.
To overcome the problem with a fixed wick a floating wick can be used. An example of a lamp
using this principle is the ‘Binga lamp’ developed by the binga trees project in Zimbabwe. As
the oil level drops, the wick sinks together with it keeping the distance between the flame and
the oil constant. An impression of the binga lamp is given below.
Coking of the wick is caused by the higher evaporation temperature of jatropha oil. Petroleum
normally evaporates from the wick while the flame burns. The flame burns at a small distance
from the wick’s surface thereby leaving the wick intact. As the jatropha oil does not evaporate
as quickly, it burns on the wick’s surface causing the formation of carbon deposits on the wick.
After 8 hours the visible part of the wick is completely carbonized and has to be replaced [1].
59
2.
Figure 5‐1 Ordinary petroleum lamp (r), modified to Figure 5‐2 Binga lamp developed in the 'Binga
run on jatropha oil (l) [2] Trees' project Zimbabwe [3]
5.2.1.2 Cooking stoves
Designs of stoves using the jatropha seed are based on three different methods. The first uses
the solid jatropha seed kernels as fuel as with the UB‐16, see Figure 5‐3. The second method
uses the jatropha oil in modified kerosene stoves with a wick. The third method utilizes the
jatropha oil, vaporized and sprayed under pressure into a specially designed stove, like the
‘Protos’. The main drawback of jatropha oil in cooking stoves is its high viscosity, which often
leads to clogging of the fuel pipe or burners. Several stoves that have been adapted to or
specifically designed for jatropha oil are shown below. Although it is documented that jatropha
stoves have very low emission levels compared to wood stoves, it is not known yet if the
smoke of jatropha fuel is harmful because of its toxic ingredients. This is an important aspect
and further research is highly recommended.
Figure 5‐3 Cooking stoves. From the left: 1) UB‐16 stove that is claimed to be directly fired with (de‐
hulled) jatropha seeds [4]; 2) The Wheel brand stove, a typical example of an adapted kerosene stove;
3) Protos plant oil stove developed by BSH Bosch and Siemens Hausgeräte GmbH
The ‘PROTOS’ plant oil stove was developed in 2004. This unusual stove can be fuelled by
unrefined and refined vegetable oils such as coconut oil, sunflower oil, rapeseed oil, jatropha
oil, castor oil, cottonseed oil and peanut oil. Except for the burner, this stove can be produced
locally thereby creating employment. Over 500 ‘‘Protos’’ stoves have been tested in the
Philippines, India, Indonesia, South Africa and Tanzania.
60
3. 5.2.2 Direct fuel for cars and driving engines for shaft power or electricity generation
Author: Niels Ansø
5.2.2.1 Introduction
By nature, PPO generally has excellent properties as fuel in diesel engines, so‐called
compression ignition engines. Generally any warm diesel engine will run on heated PPO.
Nevertheless, for generations diesel engines have been designed and optimized for diesel fuel.
Since some fuel properties of PPO differ from diesel fuel, different conditions must be
followed, and changes (conversions and modifications) must be made to the engines in order
to handle some of these different properties. The necessary changes to the engine are typically
named conversion or modification.
There are two equally important criteria to follow in order to successfully use PPO as fuel in
diesel engines:
• The PPO fuel quality should meet criteria specified in PPO fuel quality standards. Such
standards already exist in Germany for rapeseed PPO, DIN V 51 605. Similar standards
should be made for other kinds of PPO.
• The diesel engine should be selected as suitable for PPO conversion, and it should be well
maintained and in a well adjusted condition. In addition, when it’s converted, care should
be taken regarding the special challenges for that exact type of engine. And the engine
should be used in a suitable way (load pattern)
Both conditions will secure efficient combustion of the PPO, minimizing the emissions and fuel
consumption, and guarantee a normal, long lifetime of the engine. Under these conditions, the
performance and fuel consumption when running on PPO will be comparable to that of diesel.
On the other hand, if the PPO is combusted inefficiently, problems can be expected sooner or
later. Typically, this is because of deposits or other ways of accumulating unburned fuel in the
engine. Or it could be the PPO damages the injection system because of aggressive properties
leading to corrosion.
All measures, both on the engine side and on the fuel side, are simple and easy to understand.
A good, practical approach is important, and most important is not to underestimate the value
of each measure for fulfilling the criteria.
In the following chapter we try to cover the key topics relevant for running diesel engines on
PPO in developing countries. This includes requirements pf the PPO fuel, selecting engines
suitable for operation on PPO, and what has to be changed on these engines in order to
operate safely with PPO. However, this is only a guideline. The main source for this chapter is
based on Niels Ansø´s own practical experiences with Dajolka [6] (and at Folkecenter), made
during more than 10 years, driving all own cars on 100% PPO, and conducting many practical
activities including conversion of several hundreds of engines, mainly passenger cars and vans,
but also diesel engines in other applications. Any attempt to follow the advice given in this
chapter is however at one’s own risk.
5.2.2.2 PPO fuel properties
On the fuel side it is essential to care about the quality of the PPO. This starts by selecting the
right kind of crop/oilseed, cultivating and harvesting, transport, handling and storing the
oilseeds and pressing, filtering, handling and storing the PPO (See chapter 4).
61
4. The PPO fuel quality standard specifies two groups of parameters (see also Table 5‐1)
• Characteristic properties: occurring naturally and are generally unchanged by production,
handling and storing the oilseeds and PPO. These are less important as long as the kind of
crop/oilseed is known.
• Variable properties: influenced by harvest, transport, handling and storing seeds, and
production, handling and storing the PPO. These are very important for the stability of the
PPO during storing, for prevention of damage to injection systems, and for efficient
combustion of the PPO.
All parameters are important, but some are more critical than others. In Table 5‐1 the
variables in italics (which are invisible) can damage an engine fast if limits are exceeded
considerably. It makes sense to analyse the PPO for the four variable parameters on a regular
basis.
Table 5‐1 DIN V 51605 norm for rapeseed, based on the earlier Weihenstephan or RK2000. This
standard summarizes the criteria that determine the quality of SVO as an engine fuel [7]. FACT
recommends using this norm for jatropha oil in diesel engines as well. NB the properties in italics are
critical for diesel engines and should be monitored regularly (see also section 5.2.2.2)
Properties / constituents units Standards
3
Density at 15°C: 900‐930 km/m According to DIN EN ISO 3675 / 12185
Flash point: min. 220°C According to DIN EN ISO 2719
Kinematic viscosity at 40°C: max. 36.0 mm2/s According to DIN EN ISO 3104
Calorific value: min. 36,000 MJ/kg According to DIN 51900‐1, ‐2, ‐3
Ignite: min. 39
Carbon: max. 0.40% According to DIN EN ISO 10370
Iodine value 95‐125 g / 100 g According to DIN EN 14111
Sulphur content 10 mg/kg According to DIN EN ISO 20846 / 20884
Variable properties
Total contamination 24 mg/kg According to DIN EN 12662
Acid number 2.0 mg KOH / g According to DIN EN 14104
Oxidation stability at 110°C: min. 6.0 h According to DIN EN 14112
Phosphorus content: max. 12 mg/kg According to DIN EN 14107
Total magnesium and calcium: max. 20 mg/kg According to DIN EN 14538
Ash content (Oxidasche): max 0.01% According to DIN EN ISO 6245
Water: max. 0.08% According to DIN EN ISO 12937
5.2.2.3 Other properties
Another difference is the energy content, which is about 4%‐5% less per volume for PPO,
compared to fossil diesel. The lower energy content is partly compensated by more efficient
combustion caused by the natural content of oxygen in the molecule structure of PPO.
Table 5‐2 Difference in constant characteristic properties of PPO (from rapeseed) and diesel
Property Unit PPO Diesel
Density kg/m3 920 830
Energy content per weight MJ/kg min 36,0 42,3
(typically 37,0)
Energy content per volume MJ/l 33,1 35,1
Oxygen content % 11‐12 0
Flame point °C 220 60‐70
62
5. Considering the hydraulic and mechanical systems in a diesel engine, the main difference in
properties between PPO and diesel is, that the viscosity of PPO is many times higher than for
diesel at ambient temperature. This makes it more difficult for the PPO to flow from the fuel
tank to the engine and to atomize the cold PPO in the injectors. The high viscosity together
with a much higher flash point makes it more challenging to start a cold engine on PPO and get
satisfactory efficient combustion until the engine is hot.
Figure 5‐4 Viscosity
Figure 5‐4 shows the kinematic viscosity of rapeseed oil and diesel as a function of the
temperature. The blue line show viscosity of diesel, and the red line ‐ actually 3 lines on top of
each other, shows the viscosity of rapeseed oil, respectively cold pressed, super degummed
and fully refined. At 0°C the PPO is 20‐30 times more viscous than diesel, but at 60‐70°C the
viscosity is near to diesel, the curve becomes flat and the difference disappears.
Figure 5‐5 Solid/liquid phase shift
63
6. PPO can solidify at low temperatures. It’s a reversible process and is both a function of
temperature and the time. The figure shows the solid/liquid phase properties of rapeseed oil.
It must be emphasized that for jatropha PPO, these numbers will be different since,
compared to rapeseed oil, it has a different fatty acid composition with a higher share of
saturated fatty acids. Hence its viscosity curve (Figure 5‐4) will be different and solidification
point will be at higher temperature.
5.2.2.4 Engine conversion/ Engine types
To enable the engine to run safely on PPO the engine must be converted to handle the
different fuel properties of PPO compared with diesel. For example, it’s necessary to heat the
PPO in order to decrease the viscosity, and to modify injectors and glow plugs to enable the
engine to start on PPO.
Because of the large variety of engines combined with different manufactories and
configuration of injection system, this chapter can only serve as a guide to the most basic
things relevant for conversion. Only engines with mechanical controlled injection systems will
be discussed, since engines with electronically controlled injections are still not common in
developing countries, and because the conversion requires more specialized technology, tools
and mechanics trained in these systems.
As mentioned before, generally any warm diesel engine will run fine on heated PPO. The main
challenge is to get the engine started and run it with satisfactory clean combustion until it
reaches normal operating temperature – typically about 80‐90°C for a water cooled engine.
1. Identification of the engine
Diesel engines exist in many different types and sizes. Most of them can be converted to PPO
in one or the other way. It’s important to first identify and choose a suitable engine, and then
decide how it should be converted. The main question is whether the engine has direct or
indirect injection, and how the engine cooling system is designed. The cooling system is
important because it controls the engine operating temperature, and the expended heat from
the engine is used to heat the PPO.
Generally all diesel engines with InDirect Injection (IDI) are very suitable for conversion to PPO.
Engines with Direct Injection (DI) can also be converted, but they are more sensitive to the
load pattern and fuel quality, so they require more attention and are typically converted with a
duel‐tank (2‐tank) system.
It is normally not recommended to convert engines equipped with distributor injection pumps
manufactured by Lucas/CAV/Delphi, Stanadyne or Roto‐Diesel. This is because there is a high
risk of damaging the pump, typically when the pump and PPO are cold. Other engines can have
other problems, making them less suitable for conversion, e.g. DI engines with a bore/stroke
ratio > 1.
Therefore, before deciding to convert an engine, it is important to identify the engine, the type
and manufacturer of the injection system, and the typical load pattern for the engine. Based
on these factors, it’s possible to determine if conversion of that engine is feasible.
Initially it is important to determine if the engine has direct or indirect injection, identify which
type of preheating system is available (if any), the kind of injection pump and lift pump, and to
64
7. identify the kind of cooling system. It can often be helpful to make a drawing of the fuel
system, showing all components and fuel lines.
For exact identification of the engine it is important to get the following information:
Manufacturer, engine code, year of manufacture, number of cylinders, displacement (cm3),
and power(hp/kW). From the engine code it is usually possible to get all technical data for the
engine, but for some engines it’s also necessary to physically identify the manufacturer of the
fuel injection pump, because some models can be equipped with different brands.
2. Status of the engine
It’s essential that the engine is adjusted correctly and is in a well‐maintained condition. If the
engine is smoking or in other ways is not performing well on diesel, the problems should be
identified and corrected before the conversion. If the injectors are worn or the glow plugs
burned out, these could be changed in connection with the conversion. The cooling system,
including the thermostat, should work well so the engine will reach normal operating
temperature as fast as possible – otherwise, if the thermostat is defect, the engine might work
at a too low temperature for efficient PPO combustion. If no thermostat is installed, e.g. on air‐
cooled engines, the engine might cool too much because the cooling system is designed for
the worst case. The engine, therefore, may have problems to reach an acceptable
temperature, especially at low loads. It might disqualify the engine as suitable for PPO
operation. At the very least, the engine should be measured to increase the operating
temperature in a safe way.
3. Differences between DI and IDI engines
A)
A) B)
B)
C)
C)
D)
D)
E)
F) End‐
Figure 5‐6 Cross section of an IDI combustion Figure 5‐7 Cross section of a DI combustion
chamber. A) single‐hole Injector, B) glow plug, C) chamber. A) multi‐hole Injector, B) glow plug, C)
pre chamber, D) cylinder head, E) piston, F) cylinder head, D) piston, E) cylinder wall (photo:
cylinder wall (photo: Robert Bosch GmbH) Robert Bosch GmbH)
Figure 5‐6 and Figure 5‐7 show the cross section area of en IDI and DI engine, respectively. The
IDI engine is better for PPO combustion because the fuel is injected into a relatively small and
hot pre‐chamber, where the combustion starts, before it continues into the cylinder. On a DI
engine the fuel is injected directly into the cylinder, which is relatively large and cold compared
to the pre‐chamber. On both figures an active hot glow plug is shown, which is important for
65
8. the cold start and to improve the combustion of the cold engine. The glow plug will switch off
after starting, but remains activated for a few minutes.
In DI engines, especially, there’s a higher risk that unburned PPO will reach the colder cylinder
wall, which can lead to deposits on the piston and piston rings, and cause increased flow of
PPO along the cylinder wall down to the crankcase, which will dilute the lube oil. Due to its
high boiling point, PPO in the lube oil will not evaporate again as with diesel and gasoline, so
the concentration will always increase. Initially dilution of the lube oil is not a problem. After
time, with concentrations more than 10% PPO in the lube oil, the thermal load of the mixture
can cause polymerization, which leads to a sudden and dramatic increase of the viscosity of
the lube oil, causing damages or total destruction of the engine. The phenomenon is
connected both to the type and quality of the lube oil and the PPO [8].
The photo shows a lube oil sample from
a DI engine where polymerization had
happened. To illustrate how viscous the
oil is, a small amount was poured out on
a piece of A4 paper, which was then
lifted to vertical position. The photo
shows the situation after 26 seconds –
the oil flowing very slowly. With such
viscous oil there is naturally a high risk
for damaging the engine due to
insufficient lubrication and cooling. The
operator might get a warning from the
oil pressure warning lamp when starting
the engine, because oil pressure builds
up slower than normal, but the best is
to avoid this situation by frequently
checking the level and consistency of
Figure 5‐8 Sample of polymerised lubrication oil
the lube oil and taking appropriate
action.
5.2.2.5 Engine conversion
The conversion should always be done by skilled technicians, and the result of the conversion
should be evaluated by a person experienced in diesel engines. As mentioned before, generally
any warm diesel engine will run fine on heated PPO. The main challenge is to get the engine
started and run it with satisfactory clean combustion until it reaches normal operating
temperature, typically about 80‐90°C for a water cooled engine.
There are two ways to overcome the most challenging part, which is the cold start and
operation of the engine from being started until it has reached normal operating temperature.
• With a 1‐tank system, the engine starts directly on PPO. The original fuel tank can be filled
with PPO, diesel or any mixture of PPO and diesel.
• With a 2‐tank system, the engine starts on diesel supplied from a separate fuel tank, and
operates on diesel until the engine reaches normal operating temperature. Then it is
switched to heated PPO supplied from the other fuel tank. Before stopping the engine for
cooling down, it should be switched again to diesel in order to purge the injection system.
The diesel tank should always be filled with diesel, but the PPO tank can be filled with
PPO, diesel and any mixture between PPO and diesel.
66
9. 1. Realizing and operating 1‐tank systems
IDI engines can easily be converted with a single tank (1‐tank) system, enabling them to start
promptly directly on PPO. The first condition for realizing a 1‐tank system is that a glow plug
must be present in the combustion chamber (see Figure 5‐12), and it is necessary to install
special glow plugs and injectors, and to adjust the injection timing and injection pressure.
Realizing a 1‐tank system requires special focus on the injectors, glow plugs and the
adjustment of the engine. Using an engine converted with a 1‐tank system is very similar as
using the original engine with diesel. The only difference is the cold start, where the operator
must learn to start the engine on PPO – usually it just requires letting the pre‐heating work 5‐
10 seconds longer than when starting on diesel, eventually combined with adjusting the gas a
little with the accelerator. The best is to start the engine and let it heat up moderately, rather
than letting it heat up by idling or running the engine at full load and/or at high RPMs. Most
users prefer a 1‐tank system because it is easy to use and does not require changes in habits or
give any inconveniences. For these reasons it is often recommended.
Figure 5‐9 Typical configuration of 1‐tank system, including larger fuel pipes, heat exchanger,
electrical fuel heater, injectors, glow plugs relays etc.
2. Realizing and operating 2‐tank systems
Some DI engines can also be converted with a 1‐tank system, but it is much more challenging
to get prompt start and clean combustion of a cold engine, so DI engines are typically
converted by a 2‐tank system, which can relatively simple. A typical conversion for a car is
demonstrated in Figure 5‐10. For more basic engines, as used in Africa for example (Figure
5‐16, left), with no battery for electric starting, preheating and electrical controlled fuel
switching, the conversion system typically consist of the following: an extra fuel filter, fuel tank
and fuel heating system for PPO, two ball valves (one for each fuel tank), and some hoses and
fittings to connect the two fuel lines at the injection pump, and eventually to realize a loop of
the return fuel from the injection system.
Challenges are to design the system so that purging time is minimized, and to ensure that PPO
is not mixed with diesel in the diesel tank during purging process. The purging time is
minimized by decreasing the volume in the fuel system from the valve controlling the fuel
flowing to the engine and the other valve controlling the return flow. Therefore it is best to use
separate fuel filters for diesel and PPO. It will require an extra control valve on engines with
external lift pump, because it is usually placed before the fuel filter.
67
10. Realizing and operating a 2‐tank system is usually relatively simple. The engine starts on diesel
as usual, and is switched to heat PPO when the engine has reached operating temperature –
either manually by the operator or automatically via a control system, e.g. using a thermostatic
switch in combination with 3‐way solenoid valves. Before stopping the engine for cooling, the
operator must remember to switch back to diesel in due time, so the injection system will be
purged with diesel and be ready for the next start. The purging time depends on the specific
engine and the design of the 2‐tank system. For DI engines it is best to switch to diesel if idling
or running on very low load for long time. If the engine has many starts/stops, idling/low load
or only running for a short time, the 2‐tank system is not suitable because the engine will run
most of the time on diesel. The 2‐tank system is a little more inconvenient for the user
because it’s necessary to switch back to diesel in due time before stopping, and to keep an eye
on the fuel level in 2 different tanks. The extra tank for diesel takes up space, typically inside
the cabin if it’s a passenger car or a van, where increases the risk of spilling when filling up
(except if installed with extern filling system).
Figure 5‐10 Typical configuration of 2‐tank system on engines with lift pump integrated in the
injection pump. It includes larger fuel pipes, heat exchanger, extra fuel tank and fuel filter for diesel,
3‐way valves for switching between PPO and diesel, etc.
Mixing PPO to the diesel tank can be avoided by delaying the return valve, so that the return
fuel will continue running to the PPO tank during the purging process, but this will increase the
diesel consumption. Another way is to loop the return fuel back to the injection pump instead
of the diesel tank, when running on diesel. This will minimize the diesel consumption but will
increase the purging time considerably because the fuel in the injection system is replaced
only as fast as the engine consumes fuel. With return flow to the fuel tank, the fuel in the
injection system is changed much faster, because the total amount of fuel displaced by the lift
pump over the supply and return lines can be up to 5 times as much as the actual
consumption.
68
11. Figure 5‐11 Simple 2‐tank system for engines without Figure 5‐12 Another variant of a simple 2‐
electric system and fuel lift pump. The switching tank system for engines without electric
between diesel and PPO is done manually by 2 valves. system, but with original fuel lift pump (1).
The heat source for the heat exchanger depends on the This system was installed on the irrigation
options available for the specific engine, e.g. coolant, pump shown on figure 5.11. The original
lube oil, hot air or exhaust. fuel filter (2) and a heat exchanger (3) was
installed within a loop of the return fuel
from the injection pump. By looping the
fuel the fuel heating could be realised by a
fuel hose turned 1 time round the cylinder
of the air cooled engine. With only 1 fuel
filter in the loop, the purging time between
diesel and PPO is longer, but it is not
important for an engine running
permanently for many hours.
3. Running on PPO‐Diesel mixtures
PPO and diesel mix very easily, and the diesel reduces the viscosity and flash point of the
mixture. If a mixture is left in a tank for a long time without movement, the concentration of
PPO can increase in the lower layers due to the higher density, but in a frequently used vehicle
and with circulation of the fuel (return flow to fuel tank), it is normally not a problem. In cold
seasons, mixing 10‐15% diesel into the PPO can improve the cold start of the engine, but it is
normally not necessary with a good 1‐tank conversion.
It may seem attractive to run diesel engines on mixtures without conversion, and for some IDI
engines it seems to work for a long time with concentrations up to 50% PPO. But for DI engines
it’s much more risky, and the concentration which will work is much lower, e.g. max 20‐30%.
The main risk is that the engine over time will be contaminated with deposits of unburned
PPO. Initially it might seem the engine works fine, but when deposits increase, it can suddenly
lead to more serious, irreversible problems. Therefore we can generally not recommend
running on mixtures without a real conversion.
5.2.2.6 Important technical issues
1. Glow system
A glow plug in the combustion chamber is used to preheat the combustion (pre) chamber
before the cold start of the engine. This is an important device for realizing a 1‐tank system.
Typically glow plugs are a few mm longer than the original glow plugs that are installed, in
order to add more heat to the combustion (pre) chamber before the start, and so that the fuel
spray from the injectors reaches the hot tip of the glow plug. It is also an advantage to
combine longer glow plugs with a post glow system, which means that the glow plugs are
activated also a few minutes after the cold start, and thereby improve the combustion of the
69
12. cold engine. It requires a special kind of glow plugs designed for post glow applications –
otherwise the glow plugs will burn out rapidly.
There are other kinds of glow systems, such as a glow coil placed in the air intake manifold,
which will ignite a small amount of diesel fuel. Such a system will not work with PPO as fuel,
and cannot work with post glow. So the best is to convert such an engine with a 2‐tank system.
If there is no glow system, the engine should always be converted with a 2‐tank system. If the
engine is equipped with a fuel‐based pre‐ heating system, typically placed in the air intake
manifold, care should be taken that this system will be supplied with diesel.
2. Injectors
There exist many different injectors, and there might be several suitable solutions for the same
engine. 1‐tank systems require special injectors and increased injection pressure, but for a 2‐
tank system, usually the original injectors are used, and therefore not replaced unless they are
worn. Eventually the injection pressure is increased on 2‐tank system depending on the
original configuration. Change of injectors might seem complicated and expensive, but often it
will improve the performance of a used engine, and even extend its lifetime due to cleaner
combustion.
A general rule is that higher injection pressure gives a better atomizing of the fuel and
therefore a better cold start and a cleaner combustion. Therefore, the injection pressure
should be increased, at least to the maximum within the range specified by the engine
manufacturer, or slightly higher. If the injection pressure is increased much higher than the
original pressure, it can result in a delay of the injection start and a decrease in the injected
fuel amount. So it might be necessary to compensate for this by advancing the timing and
increase the fuel quantity respectively.
Another general advantage is to use injectors that inject a small pilot injection before the main
injection. That makes the combustion of the main injection faster and more complete. Pilot
injection can be realized by the shape of the injector needle, or by a 2‐spring injector
configuration. This relation was also found by the ACREVO study [7].
3. Timing
Correct injection timing is critical to the performance of the engine, especially the cold start. In
general, “early” injection increases the combustion temperature and makes the engine sound
harder, and gives a better cold start, higher torque and more efficient combustion. Late
injection can lead to bad cold start, high exhaust temperature and inefficient combustion,
which also can be noticed by grey smoke with an irritating bad smell of unburned PPO.
When adjusting the timing it’s good to aim for the earliest value in the range specified by the
manufacturer, or even to advance the timing a bit more, e.g. 2° crank shaft compared to the
original setting.
Many engines are equipped with an automatic or a manually activated cold start adjustment,
which advances the timing and increases the idle speed, thereby improving the cold start. It’s
important that this function is working and adjusted correctly.
4. Fuel system
Due to the higher viscosity and density of PPO compared to diesel, there will be higher
resistance for the fuel flowing from the fuel tank to the engine. Therefore it is important to
70
13. minimize the pressure drop, typically by increasing the diameter of the fuel lines, to eliminate
critical restrictions in the fuel system, and/or to install an electrical lift pump. Usually
increasing the diameter of the fuel lines and eliminating restrictions is enough. Critical
restrictions can be pre filter in the fuel tank or on the fuel line, or different kind of junctions or
connections of the fuel line, with reduced cross section area. Suction of air into the fuel system
is also a common troublemaker, so it’s essential to be careful with the assembly of all junctions
and connections of the whole fuel system, especially on the suction side of the injection
pump/lift pump. For trouble‐shooting it’s a good idea to install a short piece of transparent
fuel pipe just before the injection/lift pump, to see if there are any air bubbles in the fuel.
5. Materials
The materials used in the fuel system should be selected to prevent any interaction between
the material and the PPO. Copper should be avoided due to its catalytic effect on PPO, leading
to decreased oxidation stability of the PPO. Zinc‐coated steel surfaces (except if electro‐
coated) also reacts with PPO, which forms solid fat with a high melting point. The fat forms a
coating which can release in smaller pieces and flow with the PPO and block fuel filters. Use
stainless or carbon steel instead.
Figure 5‐13 Inline pre filter which was partly blocked by small particles of solid fat, released from a
small piece of zinc coated steel in the PPO tank
Many modern fuel hoses are resistant to PPO. Typically PA12 hoses are used for hard hose
connections, and fat resistant rubber hoses for the soft flexible connections, e.g. NBR or VITON
rubber. Special hoses have been developed to resist biodiesel, which are also suitable for PPO.
6. Lift pump
On most diesel engines a lift pump is used to suck the fuel from the tank and supply the
correct fuel pressure to the injection pump. It’s typically mechanical pumps, either integrated
in the injection pump or an external device attached to the engine or the injection pump.
Some engines have no lift pump, so the fuel pressure is generated by gravity due to a lifted
fuel tank. On several newer vehicles, an electrical lift pump integrated in the fuel tank
generates the fuel pressure. When converting the engine to PPO, the system should ensure
that both suction and fuel pressure are kept within the limits originally designed for that
engine.
71
14.
A vane type lift pump integrated in the injection pump usually works within a range of 0.2‐0.3
bars suction. If the suction increases, e.g. to 0.4‐0.5 bar or more, the injection pump can have
insufficient fuel pressure and fuel quantity, leading to malfunction of the injection and loss of
power. There is also an increased risk of damaging the injection pump. For the conversion and
for trouble‐shooting later on, it is useful to measure the vacuum in the fuel line before the
injection/lift pump, using a vacuum meter with scale 0‐1 bars.
External / mechanical membrane type lift pumps are usually installed before the fuel filter, and
should overcome the pressure loss through the fuel filter, and still maintain a positive pressure
at the injection pump – typically 0.1‐0.5 bar overpressure. The membrane material may not be
suitable for PPO, and therefore requires being changed more frequently. Some pumps cannot
supply enough positive pressure with cold and high viscous PPO. This situation could be
avoided by a 2‐tank solution, or modifications could be made to the lift pump, or an external
electrical lift pump could be installed either to assist or replace the original lift pump. Keep in
mind that the supply pressure at the injection pump should be within the originally specified
limits.
7. Fuel heating
Heating the PPO is commonly used to reduce the viscosity and eventually melt solid or semi‐
solid fats flowing in the liquid part of the cold PPO. The heat is typically introduced before the
fuel filter in order to reduce the pressure drop through the fuel filter, and to prevent the filter
from being blocked with solid fats in the PPO. The reduced viscosity also enables the injection
pump to handle the PPO, and it improves the performance of the injectors (atomizing). The
PPO is typically heated with excess heat from the engine, which always is available from an
internal combustion engine (60‐70% of the energy content of the fuel). Fuel temperatures
around 60‐70°C are typically reached by water cooled engines, using the coolant as a heat
source, and is self limiting due to the thermostat controlled coolant temperature. If the engine
after the conversion is meant to run on diesel from time to time, it’s wise not to heat the fuel
above 70°C due to the lubricity properties and lower boiling point of diesel, which can lead to
decreased lubricity and fuel steam bubbles in the fuel, causing wear and mechanical stress in
the injection system, and malfunction of the fuel injection. If the fuel temperature can exceed
about 70°C, e.g. using the lube oil or exhaust gas as heat source, the fuel heating system
should be disabled when running on diesel. As long as the PPO is liquid, heating the fuel tank
and the fuel lines is not necessary – and it is better for the stability of the PPO in the tank.
Water‐cooled engines usually reach operating temperature around 80‐90°C relatively fast, and
the coolant is a good heat carrier. An easy and good way to heat the PPO is by a coolant‐PPO
heat exchanger. It can be homemade, but there are many suitable plate‐heat exchangers
already used in automobile industry that are designed for fuel cooling in modern diesel
engines. These are made from aluminium, and typically have a heat transfer area of 300‐
600cm2 for passenger car engines. If a homemade heat exchanger is considered, it must be
realized that it needs quite some contact area and hence may not be too small to be effective.
On air‐cooled engines the heat source can be the lube oil, the hot air stream and radiation
from the engine or the exhaust gas. The lube oil heats slower than the coolant in a water‐
cooled engine, and oil is a less efficient heat carrier than water, but still is it a good solution to
heat the PPO by a lube oil‐PPO heat exchanger. Due to lower flow and heat capacity of the
lube oil compared to a coolant system, the heat exchanger should have a larger heat transfer
area than in a coolant‐based system.
72
15.
Figure 5‐14 Lube oil circuit on an air cooled Deutz 910 L03 engine (Source: Deutz AG)
If the engine has an external oil cooler, e.g. like a Deutz 910 (see Figure 5‐14), it is possible to
connect the heat exchanger to the hot lubrication oil flowing to the oil cooler. Or the engine
might have plugs for connecting external devices to the lubrication system, e.g. external oil
filter or cabin heater. It is necessary to get detailed technical documentation for the engine,
showing the lube oil circuit, including data for oil pressure in order to study how the lube oil
system is designed, and to figure out which maximum pressure can occur where the heat
exchanger is connected to the lube system, to avoid blasting the heat exchanger. It is also
important to fit the heat exchanger so that it cannot disturb the function of the original lube
system.
Engine Engine Engine
C) C)
A) A) A) B) Fuel
Lube oil Lube oil Lube oil
Figure 5‐15 Three variants of a simplified lube oil circuit of an air‐cooled engine. Left: the engine is
prepared for connection of external oil cooler, oil filter or cabin heater (C). Centre: External oil cooler
is installed. Right: a heat exchanger (B) has been connected to the lube oil pipe between the lube oil
pump (A) and the external oil cooler (C)
Using the exhaust as heat source is also an option, which might seem attractive, but it also has
disadvantages. There exists a technical risk that the PPO is overheated because of the high
73
16. temperature of the flue gas (up to 500°C) leading to cracking of the fuel, and a fire risk,
especially if diesel fuel is leaking inside or near the exhaust system. Due to very high difference
between fuel and exhaust gas temperature, the system cannot be self‐limiting. The fuel
temperature should be controlled by precise design and control of the fuel flow. If the
injection system includes a return line to the fuel tank, the fuel flow will be much higher than
the fuel consumption, and vary a lot depending on the engine speed, load, fuel temperature,
condition of fuel filter etc.
Fuel heating can also be realized electrically, or combined with one of the solutions described
above. Some car brands have electrical fuel heater for diesel, and retrofit solutions exist, but
many of these will switch off before the fuel has reached a temperature suitable for PPO.
Therefore an electrical fuel heater should be well selected and eventually modified for PPO.
Heating PPO with a glow plug may seem attractive, but there is a high risk that the PPO will
crack/burn due to the concentrated heat transfer of high power and a very small area.
Generally it is advised not to use electrical PPO heating alone (or at all) but to use coolant or
lube oil as the main source of heat.
5.2.2.7 Service and maintenance
After the conversion, the engine should generally be serviced and maintained as if it was still
running on diesel.
1. Fuel filter
Just after the conversion of a used engine, the fuel filter can quickly become blocked because
the PPO can release dirt and deposits in the fuel tank, and due to the higher density, PPO can
lift and move more dirt than diesel fuel. If the PPO fuel is clean, the fuel filters can last as long
as with diesel. Nevertheless, a blocked fuel filter makes more problems with PPO than with
diesel, so it is a good idea to change the fuel filter at least once a year, e.g. before a cold
season.
2. Lube oil and filter
Regarding change of lube oil and filter, it can be kept on the same service interval as for diesel
for IDI engines. For DI engines it is usually recommended to halve the change interval
compared to operation on diesel (change the oil twice as often). That is because DI engines
have a stronger tendency to get PPO diluted in the lube oil, which can lead to polymerization
(see Figure 5‐8). To prevent this from happening, it’s important to regularly check the level and
consistency of the oil in the engine. If the level has increased it’s a clear indication that the
lube oil has been diluted with PPO. The oil should be changed and the reason for the increased
level should be found. Reasons could be the many starts on PPO or a lot of idling/low load
operation, or it could be caused by inefficient combustion due to low temperature of the
engine, wrong adjustment, bad quality PPO or a defect injector. On some engines the injection
pump is attached to the engine in a way that enables fuel from a defect gasket to leak into the
lube oil.
If the engine consumes some lube oil, it’s possible to get increased PPO concentration without
an increase in oil level, so it is important also to view the consistency of the lube oil when
checking the oil level of the cold engine. If the oil suddenly seems more viscous and sticky, it’s
a sign of beginning polymerization, and the oil and filter should be changed immediately after
running the engine warm.
74
17. 3. Injectors
With a good quality, clean PPO the Injectors will last at least as long as with diesel – e.g. 150‐
200,000km, or a corresponding amount of operating hours, e.g. 3500‐5000h.
4. Glow plugs
Glow plugs in a 1‐tank application will typically last shorter because they are used more.
Typically for a passenger car, good glow plugs last 2‐4 years. For 2‐tank system, the wear on
the glow plugs are unchanged.
5.2.2.8 External components attached to the engine
The engine can be equipped with different external components, which are relevant for the
operation on PPO. Typical equipment like turbo chargers and catalytic converters is attached
to the exhaust gas system. The relevance to PPO operation is both for the function of the
components, and for the health and lifetime of the engine.
1. Exhaust Gas Recirculation
Many modern engines are equipped with an EGR system (Exhaust Gas Recirculation), which
leads a part of the exhaust gas back to the intake manifold under medium load, in order to
reduce the emission of NOX. During idling and full load the valve should remain closed. The
EGR control valve has a tendency to get stuck by deposits after years of operation. Sometimes
the valve will hang permanently in open position, and allow exhaust gas to pass even at idling,
which will make the problem with deposit worse, and at full load, will make the engine smoke
due to lack of oxygen. Therefore, it is important to observe if the EGR valve is working
properly, and if not, get it fixed and clean the valve and intake manifold from deposits.
2. Turbo
There is usually no special problem to run a turbo engine on PPO. Nevertheless a turbo charger
can be a weak point if the engine is running with bad and incomplete combustion, especially if
the lube oil gets thick due to polymerization.
3. Catalytic converter
A flue gas catalyst (catalytic converter) works fine with PPO exhaust, and helps to reduce the
smell of unburned PPO. High amounts of ash building components in the fuel (P,S, Ca, Mg) may
inhibit the function of the catalyst. Generally the application of PPO in engines with particle
filters is still not recommended because of this last reason, that particle filters are very
sensitive towards ash, and because of special challenges for the regeneration process.
5.2.2.9 Emissions
With good conversion of a healthy engine and good quality PPO meeting the fuel quality limits,
the emissions from the engine will be on the same level as with good quality diesel, or better.
Of course, the CO2 reduction by using biofuels as substitute for fossil fuel is the most important
advantage, but the emission of CO, HC and PM can also be reduced. Sulphur (S) related
emissions (SO2 and PM) are reduced due to the naturally very low content of S in PPO. NOX
emission is not connected directly to the nature of the fuel, but is generated because of the
natural excess of combustion air (with O2) in a hot diesel engine, so finally the NOX emission
can increase or decrease a little. If the engine is adjusted for earlier injection, the combustion
temperature and the NOX emission can increase, but on the other hand PM emission and fuel
consumption will decrease, due to more efficient combustion. The natural content of oxygen
(O2) in PPO improves the combustion efficiency and reduces the amount of black smoke, so
typically a PPO engine emits no black smoke. It is normal that a DI engine smokes after idling
75
18. and after cold start, but otherwise a PPO engine should not emit visible smoke. If it does, it can
be a sign of incomplete combustion, and the probable causes of the problem should be
investigated. Until solved, it’s better to run the engine on diesel.
5.2.2.10 Examples of converted engines
1. Irrigation pump (Figure 5‐16, left)
Materials used: 2 m Ø8mm rubber hose, 2 ¼” ball valves, fittings and hose clamps. Total costs
of materials about € 20. The fuel heating was realized by looping the return fuel and leading it
one time around the hot cylinder and back to the lift pump. After each single pass in the loop,
the fuel heats a little, and after few minutes operating the engine, the fuel temperature
reached about 60°C.
Figure 5‐16 Two examples of converted engines. Left: Irrigation pump with Lombardini 15 LD 440
(1 cylinder 442ccm, 10.5hp) air cooled DI engine with manual start. Converted with a simple 2‐tank
system, Honduras October 2008 (Gota Verde Project). Right: Toyota Hilux 2,8D (3L). IDI engine.
Converted by an ELSBETT 1‐tank system, Honduras October 2008 (Gota Verde Project)
2. Car engine (Figure 5‐16, right)
Material used: ELSBETT 1‐tank kit for this specific engine, including warranty and all materials
needed for the conversion. Price € 790. It is estimated that the price for a similar conversion kit
made locally would cost about € 300, excluding profit and allocations for development, testing,
documentation, warranty etc.
A remark on prices: prices vary a lot depending on the exact engines to be converted, the
quality of the conversion system, user wishes, and how and where the components for the
conversion are purchased.
5.2.3 Feedstock for soap production
Author: Titus Galema
In various countries in Africa, soap is made in villages and sometimes on a small industrial
scale, as in Tanzania (Reinhard Henning, Jatropha curcas L. in Africa, Bagani). The process of
soap‐making is relatively easy, and requires only some caustic soda and water as ingredients. If
desired, colorant and perfumes could be added to make the soap more attractive for domestic
use. The soap is often made in simple moulds (e.g from plastic bottles) and after hardening, it
is cut into handsome pieces. The soap can then be sold at a good price, which makes soap‐
making a profitable small‐scale business. The soap is mainly used for washing hands and since
76
19. medicinal properties are attributed to the jatropha soap, the soap can be sold at a good price
in Tanzania (R. Henning).
In general, soap‐making involves dissolving caustic soda in water (ca 150 g of caustic soda in
0.35 liter of water) and then mixing the oil (1 liter) with the solvent and letting it harden
overnight. Adding less water gives a harder soap, adding more water requires addition of flour
or starch to get a consistency that is solid enough. Two methods to produce soap are given in
annex D.2.
Care should be taken when handling caustic soda; Sodium hydroxide (NaOH) or potassium
hydroxide (KOH), since both are aggressive substances3 .
5.2.4 Feedstock for biodiesel production
Author: Thijs Adriaans
Instead of adapting the engine to run on PPO, the oil can also be chemically treated to produce
biodiesel. Properties of biodiesel are very similar to those of fossil diesel, and hence it can be
used in any diesel engine without adaptations. Clean, well‐produced and refined biodiesel is at
least as good an engine fuel as regular fossil diesel. It gives better ignition and combustion and
emits fewer harmful components like smoke and sulphur. The disadvantages are its slightly
lower energy content, leading to an increase in fuel consumption of about 2‐10%, and the fact
that it may work as a solvent. Biodiesel tends to clean the fuel system, taking the dirt that has
been gathered during previous diesel use, which may cause blocking of the fuel filter shortly
after switching. Furthermore its solvent nature may affect the integrity of the fuel lines and
gaskets in the fuel system, depending on their material.
5.2.4.1 Some chemistry
The production of biodiesel is essentially a simple chemical process. The vegetable oil
molecules (triglycerides) are cut to pieces and connected to alcohol (methanol or ethanol)
molecules to form methyl or ethyl esters. As a by‐product glycerin is formed. Schematically the
reaction looks like this:
fatty acid M M fatty acid
n
i n
i
r
e r
e
c
y
l
fatty acid + M M fatty acid + c
y
l
g g
fatty acid M M fatty acid
Figure 5‐17 Schematic representation of the biodiesel production process
On the left is a PPO molecule (triglyceride). Three molecules of methanol (M) are added. The
triglyceride molecule is broken into its three fatty acids and these fatty acids combine with the
methanol to form methyl esters. Glycerin combined with the lye or potassium FFA (soap)
3
Annex: safety sheet Sodium hydroxide (NaOH) and potassium hydroxide (KOH)
77
20. remains as a side product. The biodiesel molecules are each a lot smaller than the triglyceride
at the left, the main cause for its more favorable properties as a fuel. The required catalyst is
not shown in the picture, as it appears unchanged on both sides. An excellent and more
extensive description can be found on http://en.wikipedia.org/wiki/Biodiesel.
5.2.4.2 Type of alcohol
The type of alcohol used for the reaction is usually methanol, made from natural gas.
Theoretically any alcohol could be used. The advantage of using ethanol is that it can easily be
produced in a biologically, for example by fermentation. However, the use of ethanol has four
disadvantages:
1. Cost. Buying ethanol of sufficient quality is more expensive than buying methanol.
2. Processing. The esterification process with ethanol is more complicated and less
straightforward than with methanol. One of the problems is that the ethanol must be free
of water (anhydrous), which is not easily accomplished in a non‐industrial setting. The
Journey to Forever website documents why ethyl ester production is such a hassle.
3. Properties. The properties of methyl esters are more favourable than those of ethyl
esters. Especially the cold‐related properties like CFPP and viscosity lag behind. Although
these are not of such importance in tropical climates, it is advisable to convert the engine
to SVO instead of going through the hassle of producing ethyl ester since its gain in
properties is marginal.
4. Energy. For the reaction to proceed , the mixture should be heated to a temperature near
the boiling point of the alcohol. The heavier the alcohol molecule (due to more carbon
atoms) the higher the required energy input due to a higher boiling point.
For these reasons only the use of methanol is considered in this case.
5.2.4.3 Preparation of PPO feedstock
PPO can be produced from other resources, but clean, fresh vegetable oil is the easiest and
most straightforward feedstock. However, there are three kinds of properties can cause
trouble: composition, chemical impurities and physical impurities.
Physical impurities (particles, sediment) are most easily removed first. These can be
sludge/presscake from the oil seeds in fresh oil, and sand/dirt. Though the oil can be filtered
over cloth, the preferred option is to leave it alone for some weeks to sediment. Then the oil is
decanted from the sludge. Both the sludge and the water are removed in this way. The water
is clean enough to start making biodiesel if it remains clear upon shaking.
Chemical impurities need not pose problems. If the oil has been pressed fresh from oilseeds
like jatropha or rapeseed according to the guidelines in chapter 4 of this book, the oil should
be readily applicable as a feedstock. Unrefined sunflower oil should be dewaxed. If fresh oil
has been standing longer under unfavourable conditions, it is wise to check the water content
and eventually acidity (FFA, free fatty acids).
Finally the composition of the oil/fat is important (For more information about the contents
see tables in annex D.4). This primarily concerns the temperature below which the oil starts to
get hazy or even to gel/solidify. Fresh oil from jatropha, soy, sunflower or rapeseed will stay
clear and liquid down until temperatures around the freezing point (0°C) or much lower. Palm
oil, coconut oil and animal fats usually solidify at about room temperature. This poses
problems for their straight use in engines but also has consequences for the biodiesel
produced. The biodiesel will exhibit the same behavior as the oil/fat but at lower
78
21. temperatures. Biodiesel from the latter feedstocks usually only makes a suitable summer fuel,
as the fuel may gel in winter conditions. Since this property cannot be changed without large
efforts, care must be taken to choose a suitable feedstock. The same may hold for used
cooking oil, depending on the oil that was used originally. Storing samples of the used oil in the
fridge or freezer for at least several days may give some information about the temperature
behavior. If the used oil is a mixture, it may solidify partly. If so, let this happen for about a
week and then decant the liquid portion on top. This can be used after testing its behaviour in
cold.
5.2.4.4 Biodiesel production recipe
Generally this recipe can be followed to produce biodiesel from fresh PPO and methanol in a
base catalyzed environment. The recipe below is a very much summarized general guideline.
Many tips and tricks and safety recommendations have been left out for the sake of
compactness. It is good to read more about this before starting. If you would like to work with
used cooking oil, ethanol or another catalyst instead, many Internet sites can help you adapt
the recipe. Please note that the methanol and lye involved are quite dangerous chemicals. Be
sure to know what you are doing, work in a well ventilated area and wear protective clothes
and glasses!
1. Required materials
The following resources are required (all quantities are expressed per liter of PPO): 1 liter of
PPO, the younger the better; at least 3.5 grams of lye (caustic soda; NaOH (> 95%)); at least
220 ml of methanol (> 99%). Eventually you could use KOH (> 85%) instead of NaOH; then use
at least 5 grams.
2. Required actions
First dissolve the lye into the methanol. Shake or swirl until all the lye has dissolved. This may
take 10 minutes. It is normal that temperature rises. This mixture is called sodium methoxide.
Now make sure the PPO is in a vessel large enough (at least 150% of its volume), preferably
with a valve at the bottom, and heat it to about 60°C, then stop heating. Then add the
methoxide mixture and make sure it is mixed well for at least 10 minutes. Leave the vessel and
let the different constituents separate by sedimentation. The glycerin will settle out at the
bottom. After 8 to 24 hours the sedimentation is complete and the glycerine can be drained
off. It is widely advised not to try to speed up the process by shorting the settling times! What
remains is raw biodiesel. If water washing is considered difficult the biodiesel may be used
straight, although its quality may be inferior because of impurities. In this case additional
settling for at least a week is advised to get rid of the majority of soaps.
3. Magnesium silicate (bleaching earth)
Magnesium silicate is used for the purification process of the biodiesel. It provokes the
impurities to settle and it permits them to be filtered out. Settled magnesium silicate should
be handled as chemical waste.
5.2.4.5 Biodiesel refining
If the biodiesel produced is not clear, water‐washing and/or bubble‐washing will remove most
of these impurities. Bubble‐washing requires less water but needs compressed air and more
time.
Water‐washing can be applied one or more times. The first time it’s best to add a small
amount of acetic acid (vinegar) before adding the water. The acetic acid brings the pH of the
79
22. solution closer to neutral because it neutralizes and drops out any lye suspended in the
biodiesel. Add the biodiesel on top of a layer of water and stir gently. Let settle for at least a
day and separate the layers by either draining the water from the bottom or pouring the
biodiesel out gently.
Bubble‐washing works with air bubbles formed by compressed air passing through an air
stone, for instance from an aquarium shop. Add about 30 milliliters of vinegar (acetic acid) per
100 liters of biodiesel and then about 50% water. Then drop in the air stone and switch on the
air pump. The air bubbles rise through the biodiesel, carrying a film of water which washes the
biodiesel as it passes through. At the surface, the bubble bursts, leaving a small drop of water
which sinks back down through the biodiesel, washing again. If the mixture is still cloudy after
a couple of hours, add a little more vinegar. Bubble‐wash for 12 hours or longer (up to 24),
then drain off the washing water, skim off any wax floating on top. Repeat the bubble wash
two more times; keep the water from the 2nd and 3rd wash for washing the next batch. For
severe soap formations, first heat the biodiesel/soap mixture to 50°C. Add enough vinegar to
bring the pH to slightly below 7. Stir for half an hour, cool and continue with bubble‐drying as
usual.
5.2.4.6 Biodiesel by products
The main by‐product of the biodiesel process is glycerine. Other by‐products of the biodiesel
reaction and purification process are water with soap residues, magnesium silicate with soap
residues, recuperated methanol or ethanol and free fatty acids (FFA). In the following
paragraphs a short description for the applicability of these by‐products is given.
1. Glycerine
Glycerine is the simplest 3‐fold alcohol and comes into existence when the vegetable oil
molecules are split into fatty acids and glycerine during the biodiesel process. The fatty acids
react with the methanol to biodiesel. Glycerine is a high viscosity liquid with a high density
(1,26 kg/l) [11]. The name comes from the Greek word glykys meaning sweet. The amount of
glycerine that is formed in the reaction depends on the FFA level of the oil used, but can vary
between 10% and 30% of the amount of oil used. Biodiesel floats on glycerine since its density
is lower. Separating the glycerine from the biodiesel can be easily done by draining off the
bottom layer of a gravity drained decantation tank after a sedimentation time of eight hours
after the biodiesel reaction. In a continuous process, separation is done by a centrifuge based
on the density difference.
Glycerine can be used as resource for other products, including soap, organic manure, biogas,
fuel, and recycled alcohol for the biodiesel process (For details, see annex D.5.3).
2. Water with soap residues
If the biodiesel is washed with water, it dissolves the formed soaps and residual methanol. If
there would be no methanol residue present in the crude biodiesel, the wash water could be
used directly as degreasant water for internal industrial purposes. In practice there will be
methanol present, so this must be removed first. A way to do this is by heating an open drum
with the washing water in a well‐ ventilated area (preferably outdoors) to about 50°C. Don’t
inhale the vapors! A better way is to recover the methanol for reuse by distilling or flashing it
off.
80
23. 3. The recuperated alcohol (methanol)
The recuperated alcohol can be used directly in the transesterification process again. Be sure
no water is present in the recuperated alcohol. It is recommended to mix small volumes of
recuperated methanol with fresh alcohol to ensure the quality.
4. Free Fatty Acids (FFA)
The residual FFA normally are mixed with the glycerine where they can be converted into soap
(see paragraph on soap). They can also be neutralized and separated to be converted into
biodiesel through an acid/base transesterification process. Large boilers can often handle
biofuel with several percents of acid content, so the FFA could be mixed with (neutral)
vegetable oil and fired for energy generation, though this is not a very common application in
developing countries.
5.2.4.7 Concluding remarks
Making biodiesel is something that needs to be practiced. with different feedstock and
circumstances. The observations and procedures may show large variations. With more
experience, one will be able to judge the effects and streamline the processes. Use this section
as a guideline and try to use literature, for instance the excellent Journey to Forever website,
to gather more detail information.
5.3 Applications of other jatropha products
Author: Janske van Eijck
When the seeds are pressed to oil, about 20%‐30% of oil is gained. The rest remains as
presscake. Not only are all the minerals still inside this cake (PPO contains virtually no
minerals) but due to the oil content the presscake still contains a considerable amount of
energy. With its 20‐25 MJ/kg it’s about half as energy‐rich as the oil that contains 40 MJ/kg –
but the fact that there is two to four times more presscake, compensates for this.
Theoretically, the best use of the presscake is for energy purposes first, and then as a fertilizer.
Digestion to biogas for energy leaves the nutritional value intact, and use as a fertilizer implies
that the calorific value is lost. Direct combustion of the presscake, by contrast, will leave the
majority of the nutrients in the ashes, but the nitrogen will be lost with the flue gases. The
process scheme below will clarify the process.
The following by‐products can be distinguished: presscake, wooden stems and leaves.
5.3.1 Wooden stems and leaves
Jatropha leaves contains 4.7% nitrogen, 0.15% phosphorus, 3.77% potassium, 0.61% calcium,
0.49% magnesium and 0.25% sulphur. It also contains elements like zinc, boron, copper,
manganese, boron and sodium. These elements, though found in small amounts, are good for
growth, production and drought tolerance like potassium. When the plant sheds off its leaves,
these minerals go back to the soil when the leaves decompose. The wood from jatropha has an
energy content of 15.5 MJ per kilogram and nitrogen content of 3.3%, phosphorus 0.1%,
potassium 2.9% and calcium 0.3% and other trace amount of nutrients which suggests that it
can be used for firing in stoves but also useful in increasing soil nutrients after decomposition
or as ash from combustion [9]. The stems contain a milky substance, which makes direct firing
difficult, they have to be dried first
81
24. 5.3.2 Presscake
5.3.2.1 Handling
The presscake storing conditions to avoid are the following:
• Do not store at high humid temperature. The presscake is prone to fungal attack.
• Store at or below 6°C for optimal conditions, however this implies a cooling system which
for most projects will be too expensive.
• The cake should be dried to obtain a low moisture content (5‐7%) and stored in an airtight
container or otherwise stored in a dry and cool place.
• Keep the presscake away from oxidizing agents and flammable materials [15].
5.3.2.2 Presscake as a biogas generation feedstock
Biogas production from organic matter, like animal manure and agricultural waste, is produced
by small units on large scale for households in countries like China, Nepal and Vietnam. The
usual size for households is a 6 to 12 m3 holder for which 4 to 10 cows would produce
sufficient manure. Biogas is used for cooking and lighting. With a larger production it can also
be used for running gas engines. Biogas, is a mix of methane (CH4) and carbon dioxide (CO2) in
a ratio of 60‐40, with a net caloric value of approx 20 MJ/m3
Jatropha presscake can be mixed with manure from animals as cow dung or from people.
Results from lab test on behalf of FACT proved that jatropha presscake alone, when started
with fermentation bacteria to start the process, showed a fairly good production of biogas.
Based on these tests a prediction for real life productions was made as follows: CH4 content of
ca 50%‐60% and CH4 yield ca 0.5‐0.6 m3/kg. LHV between 18‐22 MJ/kg. [16]
One case where it is produced on a larger scale is with Diligent Tanzania, see the Case below.
Water is the other input ingredient and after anaerobic fermentation in the digester two
products are created, which are biogas and sludge. As with any biogas installation there is
quite a big amount of water needed for the fermentation process. If, for example, toilets can
be connected, there will be a steady water flow available. Once the biogas digester runs out of
water, all bacteria die and starting up the system again can take up to a month. This means the
biogas system has to be monitored. The bigger the system, the easier it will become to
maintain. For a 60 m3 size digester, for example, there is no problem if there would be no
water for a day or two. For smaller systems the water flow should be more constant.
IN OUT
Presscake
(60 kg/day) Biogas
(12m3/day)
Human waste
DIGESTER
(150 people/day) Slurry
(60kg/day)
Water
(1.5 m3/day)
Figure 5‐18 Process scheme biogas digester 60 m3 with combined feedstock based on the biogas
digester of Diligent (Tanzania).
82
25. The sludge which is left after the presscake is fermented can be used as a fertilizer. It has a
higher nutrient volume than the manure and in addition all pathogens have been killed during
fermentation, which gives a very clean natural fertilizer.
There are different designs for a biogas digester, most frequently used are fixed dome, floating
dome and plug flow digester (Kerkhof, 2007). The digester of the Kerkhof case is a fixed dome.
There are no special requirements for a biogas system to be able to run on jatropha presscake.
However, there is little experience with a system running on cake alone. Biogas cannot be
stored. This means the end‐user has to be close to the biogas digester. Depending on the size
of the digester (and the pressure under which the biogas is transported, 0.2 bar) a maximum of
one kilometer between the end‐user and the digester is advised. Besides using the gas in a
kitchen, a biogas generator could also be used. However for this a large digester is necessary.
The digester discussed in the case (60 m3 digester with 12 m3/day of biogas) could drive a 2 kW
engine for about 11 hours/day.
Case biogas installation at Diligent (Tanzania)
For a 60m3 digester which is fed by a combination of toilets (8 toilets for about
150 people) and Jatropha seedcake (as is the case for the digester at Diligent
Tanzania in Arusha) an amount of 60 kg of seedcake is required per day (and 1500
liters of water) to produce around 12 m3 of gas per day (which is about 20% of the
size of the digester). This amount of gas is enough to fuel three stoves in a kitchen
which serves 250 people.
Figure 5‐20 Stove run by biogas at Diligent Figure 5‐20 The 60 m3 digester at
Tanzania ltd Diligent Tanzania ltd. (installed by
Camartec, Arusha)
5.3.2.3 Presscake as briquettes for fuel
1. Presscake briquettes
Jatropha presscake has an energy content of around 25 MJ per kg. Although the presscake
already is a pressed product, its energy content per liter can be considerably increased by
compacting the material to increase its density. This process of compacting the biomass
material to increase density (biomass densification) is traditionally called briquetting. A low
pressure briquetting machine operates in a similar way as a screw press, the presscake is in
principle compressed again. The cohesion force between the presscake particles is small, so a
83