Hydraulic Design of Sewer:
Hydraulic formulae, maximum and minimum velocities in sewer, hydraulic
characteristics of circular sewer in running full and partial full conditions,
laying and testing of sewer, sewer appurtenances and network.
1. Module III
Hydraulic Design of
Sewer
Bibhabasu Mohanty
Asst. Prof.
Dept. of civil Engineering
SALITER, Ahmedabad
2. Course content…
Hydraulic formulae, maximum and
minimum velocities in sewer, hydraulic
characteristics of circular sewer in
running full and partial full conditions,
laying and testing of sewer, sewer
appurtenances and network.
3. Design of Sewers
The hydraulic design of sewers and drains, means
finding out their sections and gradients, is generally
carried out on the same lines as that of the water
supply pipes.
However, there are two major differences between
characteristics of flows in sewers and water supply
pipes.
4. The sewage contain particles in suspension, the
heavier of which may settle down at the bottom of the
sewers, as and when the flow velocity reduces, resulting
in the clogging of sewers.
To avoid silting of sewers, it is necessary that the sewer
pipes be laid at such a gradient, as to generate self
cleansing velocities at different possible discharges.
5. The sewer pipes carry sewage as gravity conduits, and
are therefore laid at a continuous gradient in the
downward direction up to the outfall point, from
where it will be lifted up, treated and disposed of.
6. Hydraulic formulae
1. Chezy’s formula
where
V= is the mean velocity [m/s],
C= is the Chézy coefficient [m½/s],
R= is the hydraulic radius (~ water depth) [m],
i= is the bottom slope[m/m].
Constant (C) is very complex. Depends on size,
shape and smoother roughness of the channel,
the mean depth etc.
C can be calculated by using Bazin’s formula.
7. 2. Bazin’s formula Where,
C = 157.6 K= Bazin’s constant
[1.81 + (K/R1/2)] R= hydraulic radius
Sr. No. Inside nature of the sewer K values
1. Very smooth 0.109
2. Smooth: bricks & concrete 0.290
3. Smooth: rubble masonry 0.833
4. Good, earthen material 1.540
5. Rough: bricks & concrete 0.500
6. Rough earthen material 3.170
8. 3. Manning’s formula
V = velocity of flow (m/s)
k =conversion factor of 1.486 (ft/m)1/3
n =Manning coefficient
Rh = hydraulic radius (m)
S = slope of the water surface
* The value of “n” is calculated by kutter’s formula
9. 4. Kutter’s formula
Where
C = Chézy's roughness coefficient
S = Friction slope
R = Hydraulic radius (m,)
n = Kutter's roughness (unit less)
k1 =Constant (23.0 SI,)
k2=Constant (0.00155 SI,)
k3= Constant (1.0 SI,)
10. 5. Hazen – William’s formula
where:
V is velocity
k is a conversion factor for the unit system k = 0.849 for
SI units)
C is a roughness coefficient
R is the hydraulic radius
S is the slope of the energy line (head loss per length of
pipe )
11. 6. Crimp and Burge’s formula
V = 83.47 R 2 / 3 S 1/ 2
Where,
V = velocity of flow (m/s)
R = hydraulic radius (m)
S = slope of the water surface
12. Minimum Velocity
The flow velocity in the sewers should be such that the
suspended materials in sewage do not get silted up; i.e.
the velocity should be such as to cause automatic self-
cleansing effect.
The generation of such a minimum self cleansing
velocity in the sewer, at least once a day, is
important, because if certain deposition takes place
and is not removed, it will obstruct free flow, causing
further deposition and finally leading to the complete
blocking of the sewer.
13. Self clearing velocity
To calculate minimum velocity of flow following
formula is used.
V=
where,
V= minimum velocity of flow in m/s.
k= size of solids in sewage varying between 0.06mm
f= Darcy’s coefficient of friction (normally 0.03)
14. es= specific gravity of solid material flowing in
sewage, varies between 1.2 to 2.65
e= specific gravity of liquid in sewage (generally
1)
g= gravitational acceleration cont.
ds= dia of solid particles in mm
15. Maximum Velocity
The smooth interior surface of a sewer pipe gets
scoured due to continuous abrasion caused by the
suspended solids present in sewage.
It is, therefore, necessary to limit the maximum
velocity in the sewer pipe. This limiting or non-
scouring velocity will mainly depend upon the material
of the sewer.
16. Effects of Flow Variation on Velocity in a
Sewer
Due to variation in discharge, the depth of flow varies,
and hence the hydraulic mean depth (r) varies.
Due to the change in the hydraulic mean depth, the
flow velocity gets affected from time to time.
It is necessary to check the sewer for maintaining a
minimum velocity of about 0.45 m/s at the time of
minimum flow (assumed to be 1/3rd of average flow).
17. The designer should also ensure that a velocity of 0.9
m/s is developed at least at the time of maximum flow
and preferably during the average flow periods also.
Moreover, care should be taken to see that at the time
of maximum flow, the velocity generated does not
exceed the scouring value.
21. Laying of Sewer
The basics of laying a residential sewer is lateral in the
ground.
You will need a starting elevation and an ending
elevation.
After the trench is excavated, when entering an open
trench, the pipe layer prepares the trench bottom by
removing loose dirt and grading the trench bottom to
allow for proper flow of sewage within the pipe.
22. You need to ensure that the material beneath the pipe
is solid so that the pipe does not "sag" after it is
backfilled.
Typically if the "original" ground beneath the new pipe
is not disturbed and graded properly, the pipe will be
adequately supported.
If the original ground is over excavated, however, you
will need to install compacted sand or gravel bedding
beneath the pipe in order to support it.
23. Once the ground is prepared, you lay the pipe on the
prepared soil.
In most cases, you should start on the low end of the
run and work your way up to the connecting point.
If you use "hub" pipe, that is, pipe with an integral pipe
built into the pipe, you should lay your first pipe
beginning on the low end of the run with the hub on
the uphill side of the pipe.
24. If you are using PVC pipe, both ends of the pipe
should be primed with purple primer prior to laying
it.
To connect the two ends of the pipe, you apply glue
to the male and to the female ends of the pipe, being
careful to not allow dirt to stick to the glued ends of
the pipe.
Insert the male end into the female end and spin the
pipe.
Hold the two pipes in place for ten seconds to ensure
that they do not come apart.
25. Once the pipes are connected, you are ready to "bed"
the pipe.
This means that you should place sand or gravel
around and over the pipe - enough to just cover the
top of the pipe.
Once this is complete, you compact the granular
material around the pipe.
It is important to pay attention to this compaction
process so that the pipe does not lift while you are
compacting.
26. Once the bedding process is complete, you are ready
to move on the next pipe.
It is important to note that as you install more pipe,
you should be backfilling the trench behind you up to
a safe level.
29. Testing of sewer
The testing of sewers is necessary as any leakage,
improper joints, straightness or obstruction of sewers
may occur during laying of sewers.
These defects may be removed or repaired after
detection.
So there are various tests by which these defects may
be detected. These tests are :-
31. Water Test
This test is carried out for sewer lines between two
manholes.
Plugging is done by rubber plug at its lower end.
Rubber plug is connected with air blown.
The upper end of sewer is plugged with a connection
to the funnel.
The sewer is filled with water and to maintain the
required head, water level in the funnel is kept 2 m
above the upper end.
32. This head varies with the material of sewer.
In case of cast iron sewer, the head should be at 9m.
The acceptable loss or head loss should not exceed 2
litres/cm of length of the sewer.
To perform this test sufficient amount of water should
be available.
34. Acceptable water loss
Max loss
Pipe Dia per metre
[mm] in 30 mins
[litres]
100 0.05
150 0.08
225 0.11
300 0.15
400 0.20
450 0.23
500 0.25
600 0.30
750 0.38
>750 seek advice
35. Air Test
When sufficient amount of water is not available,
then air test is to be carried out.
36. Air is pumped into the pipeline, usually via a hand-
pump with a control valve, until the reading on the
manometer is around 125-150mm.
The set-up is then left for 5-10 minutes to allow for
temperature stabilisation within the pipe before the
pressure is reduced to exactly 100mm on the
manometer scale.
The manometer is then monitored for a period of 5
minutes; the level of water in the manometer should
not fall below the 75mm mark during this period.
37. This is deemed to be a 'pass' and the pipeline is
declared satisfactory and can be backfilled.
However, if the level in the manometer does fall
below the 75mm mark, then the equipment should be
checked and cleaned and the pipeline examined for
leaks or defects.
If any problems are identified, they should be
rectified before re-testing.
38. Smoke Test
The purpose of smoke testing is to find potential
points of inflow and infiltration in the sanitary sewer
system that could lead to high flows during a storm.
Smoke testing forces smoke-filled air through a
sanitary sewer line.
39. The smoke under pressure will fill the main line plus
any connections and then follow the path of any leak
to the ground surface, quickly revealing the source of
the problem.
Only enough force to overcome atmospheric pressure
is required.
40. Test For Obstruction
For straightness or obstruction of pipe, this test can be
used. There are many methods for obstruction or
straightness :
1. To check the obstruction of sewer pipe, a ball of
suitable diameter is rolled down from upstream side.
The diameter of ball should be less then the diameter
sewer. If there is no obstruction, the ball can be taken
out at downstream side.
41. 2. The straightness can also be checked by placing a
lamp at one end and a mirror at the other end.
If the full circle of light is visible at other end, then the
sewer is straight and there is no obstruction.
If there is any obstruction within the sewer line, it can
also be traced out.
42. Sewer Appurtenances
Sewer appurtenances are the various accessories on
the sewerage system and are necessary for the efficient
operation of the system.
They include man holes, lamp holes, street inlets,
catch basins, inverted siphons, and so on.
43. Man-holes: Man holes are the openings of either
circular or rectangular in shape constructed on the
alignment of a sewer line to enable a person to enter
the sewer for inspection, cleaning and flushing.
They serve as ventilators for sewers, by the provisions
of perforated man-hole covers.
Also they facilitate the laying of sewer lines in
convenient length.
Man-holes are provided at all junctions of two or more
sewers, whenever diameter of sewer changes,
whenever direction of sewer line changes and when
sewers of different elevations join together.
46. Special Man-holes
Junction chambers: Man-hole constructed at the
intersection of two large sewers.
Drop man-hole: When the difference in elevation of
the invert levels of the incoming and outgoing sewers
of the man-hole is more than 60 cm, the interception
is made by dropping the incoming sewer vertically
outside and then it is jointed to the man-hole chamber.
48. Flushing man-holes: They are located at the head of a
sewer to flush out the deposits in the sewer with water.
Lamp-holes: Lamp holes are the openings constructed
on the straight sewer lines between two man-holes
which are far apart and permit the insertion of a lamp
into the sewer to find out obstructions if any inside the
sewers from the next man-hole.
50. Street inlets: Street inlets are the openings through
which storm water is admitted and conveyed to the
storm sewer or combined sewer. The inlets are located
by the sides of pavement with maximum spacing of 30
m.
51. Catch Basins: Catch basins are small settling chambers
of diameter 60 - 90 cm and 60 - 75 cm deep, which are
constructed below the street inlets. They interrupt the
velocity of storm water entering through the inlets and
allow grit, sand, debris and so on to settle in the basin,
instead of allowing them to enter into the sewers.
52. Inverted siphons: These are depressed portions of
sewers, which flow full under pressure more than the
atmospheric pressure due to flow line being below the
hydraulic grade line.
They are constructed when a sewer crosses a stream or
deep cut or road or railway line.
To clean the siphon pipe sluice valve is opened, thus
increasing the head causing flow.
Due to increased velocity deposits of siphon pipe are
washed into the sump, from where they are removed.