IRJET- Design and Fabrication of Thermo Acoustic Refrigerator

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 05 Issue: 03 | Mar-2018 www.irjet.net p-ISSN: 2395-0072
© 2018, IRJET | Impact Factor value: 6.171 | ISO 9001:2008 Certified Journal | Page 1961
DESIGN AND FABRICATION OF THERMO ACOUSTIC REFRIGERATOR
Alwin Jose1,Fredy Chacko2,Jackson K Jose3, Jomy Joseph4,Kiran Paliakkara5, Sreejith K6
1,2,3,4,5 UG Scholars, Dept. of Mechanical Engineering Jyothi Engineering College Cheruthuruthy, Kerala, India
6Ass. Professor, Dept. of Mechanical Engineering, Jyothi Engineering College Cheruthuruthy, Kerala, India
---------------------------------------------------------------------***---------------------------------------------------------------------
Abstract - A thermo acoustic refrigeration system is one of
the harmless types of refrigeration system, which which offers
a wide range of scope for further research. Some key
advantages include no emission of harmful ozone depleting
gases like cfcs and Freon and the presence of no moving parts.
This field is gathering the attention of many researchers as it
combines both the disciplines of thermal and acoustics.
Researchers have found the influence of various parametersof
the components, the working fluid, and the geometry of the
resonator on the performance of the device. Simulationsusing
software also being developed from time to time. The main
objective of the paper is to present a detailed overview on the
arrangement and functioning of therefrigerationsystemusing
high intensity sound waves. This work experimentally
investigates the performance of ceramic substrates used as
stacks in standing wave thermo acoustic coolers.
Key Words: Thermoacoustics, standing wave, ceramic
substrates, air as working medium
1. INTRODUCTION
From creating comfortable home environments to
manufacturing fast and efficient electronic devices, air
conditioning and refrigeration remain expensive yet
essential, services for bothhomesandindustries.However,in
an age of impending energy and environmental crises,
current cooling technologies continue to generate
greenhouse gases with high energy costs.
2. WORKING
Thermo acousticrefrigeration is an innovativealternativefor
cooling that is both clean and inexpensive. Through the
construction of a functional model, we will demonstrate the
effectiveness of thermo acoustics for modern cooling.
Refrigeration relies on twomajor thermodynamicprinciples.
First, a fluid’s temperature rises when compressed and falls
when expanded. Second, when two substances are placed in
direct contact, heatwill flowfromthehotter substancetothe
cooler one.
While conventional refrigerators rely on pumps to transfer
heat on a macroscopic scale, thermo acoustic refrigerators
depends on sound to generate waves of pressure that
alternately compress and relax the gas particles within the
tube. Although the model constructed for this research
projectdoes not achieve the originalgoal ofrefrigeration,the
experiment suggests that thermoacousticrefrigeratorscould
one day be viable replacements for conventional
refrigerators.
3. PRINCIPLE
Thermo acousticsis based on the principle thatsoundwaves
are pressure waves. These sound waves propagate through
the air via molecular collisions which causesadisturbancein
the air thereby creating constructive and destructive
interference. The constructive interference compresses the
air molecules while the destructive interference expands
them. This principle is the basis of thermo acoustic
refrigerator.
One method to control these pressure disturbances is with
standing waves. These waves are natural phenomena
exhibited by any wave in a closed tube. When the incident
and reflected waves overlap they interfere constructively
producing a single wave form. This wave causes vibration in
the isolated sections. These waves form nodes and
antinodes. The maximum compression of air occurs at
antinodes. Due to this antinode property standing wavesare
useful as only a small input power is required to produce a
large amplitude wave which has enough energy to cause a
visible thermo acoustic effect.
Fig -1: Sound waves
4. THERMO ACOUSTICS
Thermo acoustics combines the branches of acoustics and
thermodynamics together to move heat by using sound.
While acousticsis primarily concernedwiththemacroscopic
effects of sound transfer like coupled pressure and motion
oscillation, thermos acoustics focuses on the microscopic
temperature oscillations that accompany these pressure
changes. Thermos acoustics take advantage of these
pressure oscillations to move heat on microscopiclevel.This
results in a large temperature difference between the hot
and cold sides of the device and causes refrigeration.

4.1 Thermo acoustic cycle
The cycle by which heat transfer occurs is similar to the
Stirling cycle. The figure traces the basic thermos acoustic
cycle for a packet of gas, a collection of gasmoleculesthatact
and move together. Starting from point 1, the packet of gas
compressed and moves to the left. As the packet is
compressed, the sound wave does work on the packetofgas,
providing the power for the refrigerator. When the gas
packet is at the maximum compression, the gas ejects the
heat back into the stack since the temperature of the gas is
now higher than the temperature of the stack. This phase is
the refrigeration part of the cycle, moving the heat farther
from the bottom of the tube.
Fig- 2: Thermo acoustic cycle
The most important part of this device is the stack. The
stack consists of a large number of closely spaced surfaces
that are alignedparallel to the resonatortube.Thepurposeof
the stack is to provide a medium for heat transfer as the
sound wave oscillates through the resonator tube. The
purpose of the stack is to provide a medium where the walls
are close enough so that each time as a packet of gas move,
the temperature differential is transferred to the wall of
stack. Stack is greater than the work expended to return the
gasto the initial state.This processresultsin a net transferof
heat to the left side of the stack.Finally, inthe4thstepthegas
packets ofgas reabsorbheat from thecoldreservoirtorepeat
the heat transfer process.
4.2 Penetration Depth
The ideal spacing in a stack is thermal penetration depth.
The thermal penetration depth is the distance heat can
diffuse in a gas over a certain amount of time. For example,if
a block of aluminium is at a constant low temperature and
suddenly one side is exposed to a high temperature, the
distance that the heat penetrates the metal in one second is
the heat penetration. Asthe time passes, the heat penetrates
farther into the material, increasing the temperature of the
interior section. The thermal penetration depth for an
oscillating heat source is a function of the frequency of the
standing wave ƒ, the thermal conductivity κ, and densityρ,of
the gas, as well as the isobaric specific heat per unit mass of
the gas cp, according to the equation.
𝛿 = (κ/𝜋ƒ𝜌𝑐𝑝)0.5
4.3 Critical Temperature
The critical temperature is the temperature at which heat
will be transferred through the stack. If the temperature
difference induced by the sound wave is greater than this
critical temperature, the stack will function asa refrigerator,
transferring heat from the cold end of the tube to the warm
end. if the temperature is less than the critical temperature
then the stack will function as an acoustic engine, moving
heat from the warm region to the colder region and creating
sound waves. This temperature is important in determining
the properties of a thermos acoustic device, since efficiency
depends on a temperature differential caused by the sound
waves that is larger than the critical temperature so that a
large cooling effect is created.
5. COMPONENTS AND 2D DRAWING
The componentsof experimental setup of a thermo acoustic
refrigerators are as shown below.
Table -1: Components
Component Material Quantity
Resonator Plexi glass tube 1
Stack Steel scrap, Aluminium foil -
Speaker - 1
Amplifier - 1
Temperature sensor - 3
Fig- 3: 2D Drawing

Fig- 4: Components of control unit
The 2D drawing of the thermo acoustic refrigeratorisshown
in the figure 4 and the components of the control unit is
shown in the figure above.
6. EXPERIMENTAL INVESTIGATION
In this experiment the geometrical parameters of the stack
have been extensively researched. However, a common
methodology has been adopted. The frequency is generally
considered the independent variable, kept constant, and
individual geometrical configurations are considered the
dependent variable. The aim of this work istoinvestigatethe
geometrical aspects of the stack and study the performance
of a thermo acoustic cooler system. The paper consistsofthe
use of frequency and coupled geometry parameters as non-
independent variables and investigation of possible
interdependent relationship. Results and conclusions
increase the feasibility of this technology being introduce as
an alternative refrigerator.
Fig- 5: Stack geometries A. spiral stack, B. parallel plate, C.
honeycomb, D.corning celcor, E. pin array
Fig.-6: Stack materials A. aluminium foil, B. steel scrap
In this experiment, no heat exchangers are used asthe aimis
to study is to investigate the performance of the geometrical
stack parameters, aswell as focuson the material choice. An
electronic board was programmed to produce continuous
sound wave input to the speaker. The square wave function
was used in the experiment. An amplifier was used to
increase the magnitude of sound pressure.Amultimeterwas
used to measure the input voltage and to obtain the input
power. The input power to the loud speaker was evaluated
to be 12 W.
Time
(minutes)
Temperature ℃
(Aluminium)
Temperature ℃
(Steel srap)
0 30 30
4 29 30
8 28 29
12 27 28
16 25 27
20 23 25
24 21 24
28 20 23
32 18 21
36 17 20
Table 2. Time temperature readings
The stack was fixed at a constant position and the
experiment was conducted. We found that Aluminium foil
rolled with plastic fish net is giving more cooling effect than
steel scrap at same working conditions.
CHART -1: Temperaturs vs Time graph

Our next objective wasto find the optimum stack length and
stack position. Firstly we created a stack of length 100 mm.
We conducted the test with the stack for 30 minutes and
then reduced the stack length by 10 mm. Again the test is
conducted. After conducting the test we found that 70 mm
stack length is giving a maximum temperature difference of
13 ℃. Then the objective was to find the optimum stack
position from the fixed end. It was found that as the stack
move towards the fixed end cooling effect increases. The
results and the graphs are plotted below.
Table -3: Stack length optimization
Stack
length(mm)
Stack position from
the fixed end(mm)
Maximum
temperature
difference(℃)
100 200,150,100,50 8
90 200,150,100,50 9
80 200,150,100,50 11
70 200,150,100,50 13
60 200,150,100,50 12
50 200,150,100,50 11
60 200,150,100,50 9
50 200,150,100,50 7
0 200,150,100,50 6
30 200,150,100,50 3
CHART -2, 3: Temperature difference vs Stack length &
Temperature difference vs Stack position
Fig- 9: Fabricated model
7. CONCLUSION
In this paper an experimental set up was used to investigate
the performance of the thermo acoustic refrigerator
consisting of a loud speaker driven thermo acoustic
refrigerator. Material choice and manufacturing of the stack
are important factors affecting the performance or the
efficiency of thermo acoustic refrigerator (TAR). One of the
main attributes of the TAR, is the sustainability it offers. It is
for these reasons that ceramic substrates were used as the
stack choice for these experiments. Geometrical
configurations such as porosity, stack length and stack
position were used to study the performance of TAR. The
results show that there is a maximum temperature
difference when the stack is located closer to closed end of
resonator tube. The relationship between the geometrical
parameters describing the ceramic substrates, and the
measured temperature difference related to the TAR
performance were nonlinear. This suggests that further
studies on the interdependence between the geometrical
parameters and the corresponding frequencies are
necessary. We strongly believe that furtherresearchesinthis
field will open up opportunities to cool an auditorium or a
stadium by the sound energy produced in it. Also it will be
green idea in this era of increase global warming and energy
scarcity.
ACKNOWLEDGMENT
We thank Mr. Sreejith K, who is the professor in mechanical
engineering at Jyothi Engineering College Cheruthuruthy,for
his guidance and support. We are also thankful to the entire
Mechanical Engineering Department of Jyothi Engineering
College for their suggestions and help.
REFERENCES
[1] Nor Atiqah Zolpakar “Performance of a 3D-printed stack
in a standing wave thermoacoustic refrigerator” The 8th
International Conference on Applied Energy – ICAE2016

[2] A. H. Ibrahim “Geometrical Optimization of
Thermoacoustic Heat Engines” 49th AIAA Aerospace
Sciences Meeting including the New Horizons Forum and
Aerospace Exposition 4 - 7 January 2011, Orlando, Florida
[3] Daniel A. Russell and Pontus Weibull, “Tabletop thermo
acoustic refrigerator for demonstrations”, Am. J. Phys. 70
(12), December 2002.
[4]. S.W.K. Yuan. “Thermal Management of Computer
Systems Using Active Cooling of Pulse Tube Refrigerators.”

IRJET- Design and Fabrication of Thermo Acoustic Refrigerator

More Related Content

IRJET- Design and Fabrication of Thermo Acoustic Refrigerator