The document discusses paging channels and procedures in 3GPP networks. It describes:
1) The Paging Channel (PCH) is a downlink transport channel that broadcasts paging messages to UEs over the entire cell. System Information Block 5 defines which Secondary Common Control Physical Channels (SCCPCHs) carry PCHs.
2) UEs select a SCCPCH to monitor based on the IMSI number. Paging Indicator Channels (PICH) are associated with SCCPCHs and indicate which UEs have a paging message. Paging messages are transmitted on the PCH in SCCPCH frames starting 7680 chips after the associated PICH frame.
Report
Share
Report
Share
1 of 3
More Related Content
Paging
1. Paging
The Paging Channel (PCH) is a downlink transport channel. The PCH is always transmitted
over the entire cell. The transmission of the PCH is associated with the transmission of physical-
layer generated Paging Indicators, to support efficient sleep-mode procedures.
Paging Channel selection
System information block type 5 (SIB 5) defines common channels to be employed in Idle mode.
In a cell, a single or several PCHs may be established. Each Secondary Common Control
Physical Channel (SCCPCH) indicated to the UE in system information may carry up to one
PCH. Thus, for each defined PCH there is one uniquely associated PICH also indicated.
In case that more than a single PCH and associated PICH are defined in SIB 5, the UE shall
perform a selection according to the following rule:
The UE shall select a SCCPCH from the ones listed in SIB 5 based on IMSI as follows:
"Index of selected SCCPCH" = IMSI mod K,
where K is equal to the number of listed SCCPCHs which carry a PCH (i.e. SCCPCHs carrying
FACH only shall not be counted). These SCCPCHs shall be indexed in the order of their
occurrence in SIB 5 from 0 to K-1.
"Index of selected SCCPCH" identifies the selected SCCPCH with the PCH and the uniquely
associated PICH to be used by the UE. If the UE has no IMSI, for instance when making an
emergency call without USIM, the UE shall use as default number IMSI = 0.
The UE may use Discontinuous Reception (DRX) in idle mode in order to reduce power
consumption. When DRX is used the UE needs only to monitor one Page Indicator, PI, in one
Paging Occasion per DRX cycle.
The Paging Indicator Channel (PICH) is a fixed rate (SF=256) physical channel used to carry
the paging indicators. The PICH is always associated with an S-CCPCH to which a PCH
transport channel is mapped. Picture below illustrates the frame structure of the PICH. One PICH
radio frame of length 10 ms consists of 300 bits. Of these, 288 bits are used to carry paging
indicators. The remaining 12 bits are not formally part of the PICH and shall not be transmitted
(DTX). The part of the frame with no transmission is reserved for possible future use.
2. Structure of Paging Indicator Channel (PICH)
Two Paging Procedures:
Paging procedure is used to transmit paging information to selected UEs in idle mode,
CELL_PCH or URA_PCH state using the paging control channel (PCCH). Upper layers in the
network may request paging, to e.g. establish a signalling connection. UTRAN may initiate
paging for UEs in CELL_PCH or URA_PCH state to trigger a cell update procedure. In addition,
UTRAN may initiate paging for UEs in idle mode, CELL_PCH and URA_PCH state to trigger
reading of updated system information. UTRAN initiates the paging procedure by transmitting a
PAGING TYPE 1 message on an appropriate paging occasion on the PCCH.
UE dedicated paging procedure is used to transmit dedicated paging information to one UE in
connected mode in CELL_DCH or CELL_FACH state. Upper layers in the network may request
initiation of paging. For a UE in CELL_DCH or CELL_FACH state, UTRAN initiates the
procedure by transmitting a PAGING TYPE 2 message on the DCCH using AM RLC.
Two Paging Message Types:
PAGING TYPE 1 message is used to send information on the paging channel. One or several
UEs, in idle or connected mode, can be paged in one message, which also can contain other
information
PAGING TYPE 2 message is used to page an UE in connected mode (CELL_DCH or
CELL_FACH state), when using the DCCH for CN originated paging.
PICH / S-CCPCH timing relation
Picture below illustrates the timing between a PICH frame and its associated single S-CCPCH
frame, i.e. the S-CCPCH frame that carries the paging information related to the paging
indicators in the PICH frame. A paging indicator set in a PICH frame means that the paging
message is transmitted on the PCH in the S-CCPCH frame starting tPICH chips after the
transmitted PICH frame.
3. Timing relation between PICH frame and associated S-CCPCH frame
tPICH = 7680 chips (3 slots)
Paging Block Periodicity (PBP): Period of the occurrence of Paging Blocks. (For FDD, PBP = 1).
Paging occasion: (FDD) The SFN of the PICH frame where the UE monitors its paging indicator (i.e. the SFN of
the PCCPCH frame in which the PICH frame begins).
Further reading: 3GPP TS 25.211 25.304