This document provides a quick start guide for installing, starting up, and programming a PowerFlex 400 Adjustable Frequency AC Drive. It summarizes the basic steps and safety precautions required. For full installation instructions and technical specifications, users should refer to the detailed PowerFlex 400 User Manual. The guide covers mounting considerations, wiring requirements, input/output specifications, and agency certifications for the drive.
Report
Share
Report
Share
1 of 28
Download to read offline
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
More Related Content
Power flex400
1. Quick Start
PowerFlex 400 Adjustable
Frequency AC Drive
FRN 4.xx
This Quick Start guide summarizes the basic steps needed to install,
start-up and program the PowerFlex 400 Adjustable Frequency AC
Drive. The information provided Does Not replace the User Manual
and is intended for qualified drive service personnel only.
For detailed PowerFlex 400 information including EMC instructions,
application considerations and related precautions refer to the
PowerFlex 400 User Manual, Publication 22C-UM001… supplied with
the drive or at www.rockwellautomation.com/literature.
General Precautions
!
ATTENTION: The drive contains high voltage capacitors which take
time to discharge after removal of mains supply. Before working on
drive, ensure isolation of mains supply from line inputs [R, S, T (L1,
L2, L3)]. Wait three minutes for capacitors to discharge to safe voltage
levels. Failure to do so may result in personal injury or death.
A darkened LCD display and LEDs is not an indication that capacitors
have discharged to safe voltage levels.
!
ATTENTION: Only qualified personnel familiar with adjustable
frequency AC drives and associated machinery should plan or
implement the installation, start-up and subsequent maintenance of the
system. Failure to comply may result in personal injury and/or
equipment damage.
!
ATTENTION: This drive contains ESD (Electrostatic Discharge)
sensitive parts and assemblies. Static control precautions are required
when installing, testing, servicing or repairing this assembly.
Component damage may result if ESD control procedures are not
followed. If you are not familiar with static control procedures,
reference A-B publication 8000-4.5.2, “Guarding Against Electrostatic
Damage” or any other applicable ESD protection handbook.
2. English-2 PowerFlex 400 Adjustable Frequency AC Drive Quick Start
• Mount the drive upright on a flat, vertical and level surface.
• Protect the cooling fan by avoiding dust or metallic particles.
• Do not expose to a corrosive atmosphere.
• Protect from moisture and direct sunlight.
Maximum Surrounding Air Temperature
!
ATTENTION: An incorrectly applied or installed drive can result in
component damage or a reduction in product life. Wiring or application
errors, such as, undersizing the motor, incorrect or inadequate AC
supply, or excessive ambient temperatures may result in malfunction of
the system.
!
ATTENTION: The bus regulator function is extremely useful for
preventing nuisance overvoltage faults resulting from aggressive
decelerations, overhauling loads, and eccentric loads. However, it can
also cause either of the following two conditions to occur.
1. Fast positive changes in input voltage or imbalanced input voltages
can cause uncommanded positive speed changes;
2. Actual deceleration times can be longer than commanded
deceleration times
However, a “Stall Fault” is generated if the drive remains in this state
for 1 minute. If this condition is unacceptable, the bus regulator must be
disabled (see parameter A187).
Mounting Considerations
Frame Screw Size Screw Torque
C M5 (#10-24) 2.45-2.94 N-m (22-26 lb.-in.)
D M8 (5/16 in.) 6.0-7.4 N-m (53.2-65.0 lb.-in.)
E M8 (5/16 in.) 8.8-10.8 N-m (78.0-95.3 lb.-in.)
F M10 (3/8 in.) 19.6-23.5 N-m (173.6-208.3 lb.-in.)
Frame Enclosure Rating Temperature Range Minimum Mounting
Clearances
C IP 20/UL Open-Type -10° to 45°C (14° to 113°F) Figure 1: Option A
IP 30/NEMA 1/UL Type 1(1)
(1)
Frame C drives require installation of the PowerFlex 400 IP 30/NEMA 1/UL Type 1
option kit to achieve this rating.
-10° to 45°C (14° to 113°F) Figure 1: Option B
IP 20/UL Open-Type -10° to 50°C (14° to 122°F) Figure 1: Option B
D, E, F IP 30/NEMA 1/UL Type 1 -10° to 45°C (14° to 113°F) Figure 2:
3. PowerFlex 400 Adjustable Frequency AC Drive Quick Start English-3
Minimum Mounting Clearances
Figure 1: Frame C Mounting Clearances
Figure 2: Frames D, E and F Mounting Clearances
120 mm
(4.7 in.)
120 mm
(4.7 in.)
120 mm
(4.7 in.)
120 mm
(4.7 in.)
25 mm
(1.0 in.)
Mounting Option B
Mounting Option A
No clearance required
between drives.
150 mm
(6.0 in.)
150 mm
(6.0 in.)
50 mm
(2.0 in.)
50 mm
(2.0 in.)
250 mm
(9.8 in.)
150 mm
(6.0 in.)
50 mm
(2.0 in.)
50 mm
(2.0 in.)
Frame D & E Frame F
General Grounding Requirements
PEL1
R
L2
S
L3
T
T1
U
T2
V
T3
W
PE
Required
Input Fusing
Required Branch
Circuit Disconnect
4. English-4 PowerFlex 400 Adjustable Frequency AC Drive Quick Start
Ungrounded Distribution Systems
Phase to Ground MOV Removal
Note: Frame D drives do not contain a MOV to ground connection and
are suitable for operation in both grounded and ungrounded distribution
systems without modification.
Refer to the PowerFlex 400 User Manual supplied with the drive for
details on how to comply with the Low Voltage (LV) and
Electromagnetic Compatibility (EMC) Directives.
EMC Line Filters
!
ATTENTION: PowerFlex 400 drives contain protective MOVs that
are referenced to ground. These devices must be disconnected if the
drive is installed on an ungrounded or resistive grounded distribution
system.
Frame C Frame E & F
R/L1
S/L2
T/L3
1 2 3 4
Important:
Tighten screw after
jumper removal.
CE Conformity
240V 50/60 Hz 3-Phase 480V 50/60 Hz 3-Phase
kW HP
Catalog
Number kW HP
Catalog
Number
2.2 3.0 22-RF034-CS 2.2 3.0 22-RF018-CS
4.0 5.0 22-RF034-CS 4.0 5.0 22-RF018-CS
5.5 7.5 22-RF034-CS 5.5 7.5 22-RF018-CS
7.5 10 22-RF034-CS 7.5 10 22-RF018-CS
11 15 22-RFD070 11 15 22-RF026-CS
15 20 22-RFD100 15 20 22-RFD036
18.5 25 22-RFD100 18.5 25 22-RFD050
22 30 22-RFD150 22 30 22-RFD050
30 40 22-RFD150 30 40 22-RFD070
37 50 22-RFD180 37 50 22-RFD100
45 60 22-RFD100
55 75 22-RFD150
75 100 22-RFD180
90 125 Consult Factory
110 150 Consult Factory
5. PowerFlex 400 Adjustable Frequency AC Drive Quick Start English-5
Specifications, Fuses and Circuit Breakers
Drive Ratings
Catalog
Number
Output Ratings Input Ratings Branch Circuit Protection Power
Dissipation
kW (HP)
Amps
Voltage
Range kVA Amps
Fuses
(1)
140M Motor
Protectors
(2) (3) Contactors
Min.
Enclosure
Volume(4)
(in.3)
IP20 Open
Watts50°C
200 - 240V AC – 3-Phase Input, 0 - 230V 3-Phase Output
22C-B012N103 2.2 (3.0) 12 180-265 6.5 15.5 20 140M-F8E-C16 100-C23 5098 146
22C-B017N103 3.7 (5.0) 17.5 180-265 8.8 21 30 140M-F8E-C25 100-C37 5098 207
22C-B024N103 5.5 (7.5) 24 180-265 10.9 26.1 35 140M-F8E-C32 100-C37 5098 266
22C-B033N103 7.5 (10) 33 180-265 14.4 34.6 45 140M-F8E-C45 100-C45 5098 359
22C-B049A103 11 (15) 49 180-265 21.3 51 70 – 100-C60 – 488
22C-B065A103 15 (20) 65 180-265 28.3 68 90 – 100-C85 – 650
22C-B075A103 18.5 (25) 75 180-265 32.5 78 100 – 100-D95 – 734
22C-B090A103 22 (30) 81 180-265 38.3 92 125 – 100-D110 – 778
22C-B120A103 30 (40) 120 180-265 51.6 124 175 – 100-D180 – 1055
22C-B145A103 37 (50) 130 180-265 62.4 150 200 – 100-D180 – 1200
380 - 480V AC – 3-Phase Input, 0 - 460V 3-Phase Output
22C-D6P0N103 2.2 (3.0) 6 340-528 6.3 7.5 10 140M-D8E-C10 100-C09 5098 105
22C-D010N103 4.0 (5.0) 10.5 340-528 10.9 13 20 140M-D8E-C16 100-C16 5098 171
22C-D012N103 5.5 (7.5) 12 340-528 11.9 14.2 20 140M-D8E-C16 100-C23 5098 200
22C-D017N103 7.5 (10) 17 340-528 15.3 18.4 25 140M-D8E-C20 100-C23 5098 267
22C-D022N103 11 (15) 22 340-528 19.2 23 30 140M-F8E-C32 100-C30 5098 329
22C-D030N103 15 (20) 27 340-528 25.8 31 40 140M-F8E-C32 100-C37 5098 435
22C-D038A103 18.5 (25) 38 340-528 33.3 40 50 140M-F8E-C45 100-C60 9086 606
22C-D045A103 22 (30) 45.5 340-528 39.1 47 60 – 100-C60 – 738
22C-D060A103 30 (40) 54 340-528 53.3 64 80 – 100-C85 – 664
22C-D072A103 37 (50) 72 340-528 60.7 73 100 – 100-C85 – 1019
22C-D088A103 45 (60) 88 340-528 74.9 90 125 – 100-D110 – 1245
22C-D105A103 55 (75) 105 340-528 89 107 150 – 100-D140 – 1487
22C-D142A103 75 (100) 128 340-528 124.8 150 200 – 100-D180 – 2043
22C-D170A103 90 (125) 170 340-528 142 170 250 – 100-D250 – 2617
22C-D208A103 110 (150) 208 340-528 167 200 250 – 100-D250 – 3601
(1)
Recommended Fuse Type: UL Class J, CC, T or Type BS88; 600V (550V) or equivalent.
(2) The AIC ratings of the Bulletin 140M Motor Protector Circuit Breakers may vary. See Bulletin 140M
Motor Protection Circuit Breakers Application Ratings.
(3) Manual Self-Protected (Type E) Combination Motor Controller, UL listed for 208 Wye or Delta, 240
Wye or Delta, 480Y/277 or 600Y/347. Not UL listed for use on 480V or 600V Delta/Delta, corner
ground, or high-resistance ground systems.
(4)
When using a Manual Self-Protected (Type E) Combination Motor Controller, the drive must be
installed in a ventilated or non-ventilated enclosure with the minimum volume specified in this
column. Application specific thermal considerations may require a larger enclosure.
6. English-6 PowerFlex 400 Adjustable Frequency AC Drive Quick Start
Category Specification
Agency
Certification
Listed to UL508C and CAN/CSA-22.2
Listed to UL508C for plenums
Certified to AS/NZS, 1997 Group 1, Class A
Marked for all applicable European Directives
EMC Directive (89/336)
EN 61800-3, EN 50081-1, EN 50082-2
Low Voltage Directive (73/23/EEC)
EN 50178, EN 60204
The drive is also designed to meet the appropriate portions of the following specifications:
NFPA 70 - US National Electrical Code
NEMA ICS 3.1 - Safety standards for Construction and Guide for Selection, Installation and
Operation of Adjustable Speed Drive Systems.
IEC 146 - International Electrical Code.
Protection Bus Overvoltage Trip: 200-240V AC Input: 405V DC bus voltage (equivalent to 290V AC
incoming line)
380-460V AC Input: 810V DC bus voltage (equivalent to 575V AC
incoming line)
Bus Undervoltage Trip: 200-240V AC Input: 210V DC bus voltage (equivalent to 150V AC
incoming line)
380-480V AC Input: 390V DC bus voltage (equivalent to 275V AC
incoming line)
Power Ride-Thru: 100 milliseconds
Logic Control Ride-Thru: 0.5 seconds minimum, 2 seconds typical
Electronic Motor Overload
Protection:
Provides class 10 motor overload protection according to NEC
article 430 and motor over-temperature protection according to
NEC article 430.126 (A) (2). UL 508C File 29572.
Overcurrent: 180% hardware limit, 220% instantaneous fault
Ground Fault Trip: Phase-to-ground on drive output
Short Circuit Trip: Phase-to-phase on drive output
Electrical Efficiency: 97.5% at rated amps, nominal line voltage
Control Output Frequency: 0-320 Hz (programmable)
Control
Inputs
Digital: Quantity: (3) Semi-programmable
(4) Programmable
Type
Source Mode (SRC):
Sink Mode (SNK):
18-24V = ON, 0-6V = OFF
0-6V = ON, 18-24V = OFF
Analog: Quantity: (1) Isolated, –10 to 10V or 4-20mA
(1) Non-isolated, 0 to 10V or 4-20mA
Specification
Resolution:
0 to 10V DC Analog:
4-20mA Analog:
External Pot:
10-bit
100k ohm input impedance
250 ohm input impedance
1-10k ohm, 2 Watt minimum
Control
Outputs
Relay: Quantity: (2) Programmable Form C
Specification
Resistive Rating:
Inductive Rating:
3.0A at 30V DC, 3.0A at 125V, 3.0A at 240V AC
0.5A at 30V DC, 0.5A at 125V, 0.5A at 240V AC
Optional
Relay
Card:
Quantity: (6) Optional Programmable Form A (Drive Frames D, E & F Only)
Specification
Resistive Rating:
Inductive Rating:
0.1A at 30V DC Class II circuits, 3.0A at 125V,
3.0A at 240V AC
0.1A at 30V DC Class II circuits, 3.0A at 125V
3.0A at 240V AC
Opto: Quantity: (1) Programmable
Specification: 30V DC, 50mA Non-inductive
Analog: Quantity: (2) Non-Isolated, 0-10V or 4-20mA
Specification
Resolution:
0 to 10V DC Analog:
4-20mA Analog:
10-bit
1k ohm minimum
525 ohm maximum
UL®
C US
7. PowerFlex 400 Adjustable Frequency AC Drive Quick Start English-7
Figure 3: Power Terminal Blocks
Power Wiring
Terminal (1)
Description
R/L1, S/L2, T/L3 3-Phase Input
U/T1 To Motor U/T1
=
Switch any two motor
leads to change
forward direction.
V/T2 To Motor V/T2
W/T3 To Motor W/T3
P2, P1
DC Bus Inductor Connection
Drives are shipped with a jumper between Terminals
P2 and P1. Remove this jumper only when a DC Bus
Inductor will be connected. Drive will not power up
without a jumper or inductor connected.
DC–, DC+ DC Bus Connection (Frame C Drives)
P2, DC– DC Bus Connection (Frame D, E, and F Drives)
BR+, BR– Not Used
Safety Ground - PE
(1) Important: Terminal screws may become loose during shipment. Ensure that all
terminal screws are tightened to the recommended torque before applying power to
the drive.
R/L1 S/L2 T/L3 P1 P2 DC– U/T1 V/T2 W/T3
R/L1 S/L2 T/L3 P1 P2 DC– U/T1 V/T2 W/T3
R/L1 S/L2 T/L3 U/T1 V/T2 W/T3 P2 P1
BR–BR+DC+DC–
R/L1S/L2T/L3 P1 P2 DC– U/T1V/T2W/T3
R/L1 S/L2 T/L3 P1 P2 DC– U/T1 V/T2W/T3
8. English-8 PowerFlex 400 Adjustable Frequency AC Drive Quick Start
Power Terminal Block Specifications
Important: Frame C, D, and F drives utilize a finger guard over the
power wiring terminals. Replace the finger guard when
wiring is complete.
Refer to the PowerFlex 400 User Manual for maximum power cable
length recommendations.
Input Power Conditions
Frame Maximum Wire Size(1)
(1)
Maximum/minimum sizes that the terminal block will accept - these are not
recommendations. If national or local codes require sizes outside this range, lugs may
be used.
Minimum Wire Size(1)
Recommended
Torque
C 8.4 mm2
(8 AWG) 1.3 mm2
(16 AWG) 2.9 N-m (26 lb.-in.)
D 33.6 mm2
(2 AWG) 8.4 mm2
(8 AWG) 5.1 N-m (45 lb.-in.)
E 480V
37-45 kW
(50-60 HP)
33.6 mm2
(2 AWG) 3.5 mm2
(12 AWG) 5.6 N-m (49.5 lb.-in.)
E 240V
30-37 kW
(40-50 HP)
480V
55-75 kW
(75-100 HP)
107.2 mm2
(4/0 AWG) 53.5 mm2
(1/0 AWG) 19.5 N-m (173 lb.-in.)
F 152.5 mm2
(300 MCM) 85.0 mm2
(3/0 AWG) 19.5 N-m (173 lb.-in.)
Input Power Condition Corrective Action
Low Line Impedance (less than 1% line
reactance)
• Install Line Reactor(1)
• or Isolation Transformer
(1) Refer to the PowerFlex 400 User Manual for accessory ordering information.
Line has power factor correction capacitors • Install Line Reactor(1)
• or Isolation Transformer
Line has frequent power interruptions
Line has intermittent noise spikes in excess of
6000V (lightning)
Phase to ground voltage exceeds 125% of
normal line to line voltage
• Remove MOV jumper to ground
(Frame C, E & F drives only)
• or Install Isolation Transformer with
grounded secondary if necessary
Ungrounded distribution system
9. PowerFlex 400 Adjustable Frequency AC Drive Quick Start English-9
I/O Terminal Block Specifications
(2)
Maximum/minimum sizes that the terminal block will accept - these are not
recommendations.
Refer to the PowerFlex 400 User Manual for maximum control cable
length recommendations.
I/O Wiring Recommendations
Wire Type(s) Description Minimum
Insulation Rating
Belden 8760/9460
(or equiv.)
0.8 mm2
(18AWG), twisted pair, 100%
shield with drain.(1)
(1)
If the wires are short and contained within a cabinet which has no sensitive circuits,
the use of shielded wire may not be necessary, but is always recommended.
300V
60 degrees C
(140 degrees F)
Belden 8770
(or equiv.)
0.8 mm2
(18AWG), 3 conductor, shielded for
remote pot only.
Frame Maximum Wire Size (2) Minimum Wire Size (2) Torque
C, D, E, F 1.3 mm2
(16 AWG) 0.13 mm2
(26 AWG) 0.5-0.8 N-m (4.4-7 lb.-in.)
10. English-10 PowerFlex 400 Adjustable Frequency AC Drive Quick Start
(1)
Important: I/O Terminal 01 is always a coast to stop input
except when P036 [Start Source] is set to option 1 “3-Wire” or
6 “2-W Lvl/Enbl”. In three wire control, I/O Terminal 01 is
controlled by P037 [Stop Mode]. All other stop sources are
controlled by P037 [Stop Mode].
Important: The drive is shipped with a jumper installed
between I/O Terminals 01 and 11. Remove this jumper when
using I/O Terminal 01 as a stop or enable input.
(2) Two wire control shown. For three wire control use a momentary input on I/O Terminal 02 to command a
start. If reverse is enabled by A166, use a maintained input for I/O Terminal 03 to change direction.
(3)
When using an opto output with an inductive load such as a relay, install a recovery diode parallel to the relay as
shown, to prevent damage to the output.
(4) When the ENBL enable jumper is removed, I/O Terminal 01 will always act as a hardware enable, causing a
coast to stop without software interpretation.
(5) Most I/O terminals labeled “Common” are not referenced to the safety ground (PE) terminal and are designed to
greatly reduce common mode interference. On Frame D and E drives, Analog Common 1 is referenced to
ground.
(6) Common for Analog Input 2 (AI2). Electronically isolated from digital I/O and opto output. Not to be used with
Analog Input 1 (AI1), Analog Output 1 (AO1) or Analog Output 2 (AO2). With Analog Input 2, provides one fully
isolated analog input channel.
Control Terminal Block
04
05
06
07
01
02
03
08
09
10
12
13
14
15
16
17
18
19
20
11
Digital Common
Digital Common
Digital Input 1
Digital Input 2
Digital Input 3
Stop/
Function Loss
(1)(4)
Start/Run FWD
(2)
Direction/Run REV
Digital Input 4
Opto Common
R1
R2
R3
#1 Relay N.O.
#1 Relay Common
#1 Relay N.C.
+24V DC Source
+10V DC Source
Analog Input 1 (AI1)
Analog Common 1
Analog Output 2 (AO2)
Analog Output 1 (AO1)
Analog Input 2 (AI2)
Analog Common 2
(6)
Opto Output
RS485 Shield
+24V
+10V
R4
R5
R6
#2 Relay N.O.
#2 Relay Common
#2 Relay N.C.
Typical
SNKWiring
Typical
SRCWiring
RS485
(DSI)
Enable
(4)
Jumper
30V DC
50mA
Non-inductive
Common
24V
ENBL
(3)
Pot must be
1-10k ohm
2 Watt Min.
SRCSNK
SNK
SRC
Earth Referenced
Frames D & E
(5)
0-10V
0-20mA
0-10V
0-20mA
0-10V
0-20mA
1 of 7 Digital Input Circuits
10V 20MA
AO1
10V 20MA
AO2
10V 20MA
AI1
10V 20MA
AI2
Isolated
P036 [Start Source] Stop I/O Terminal 01 Stop
Keypad Per P037 Coast
3-Wire Per P037 Per P037(4)
2-Wire Per P037 Coast
RS485 Port Per P037 Coast
11. PowerFlex 400 Adjustable Frequency AC Drive Quick Start English-11
Control I/O Terminal Designations
No. Signal Default Description Param.
01 Stop (1)
/
Function Loss
Coast Factory installed jumper or a normally closed input must
be present for the drive to start.
Program with P036 [Start Source].
P036 (1)
02 Start/Run FWD – HAND Mode: Command comes from Integral Keypad.
AUTO Mode: I/O Terminal 02 is active.
Program with P036 [Start Source].
P036, P037
03 Direction/Run REV Rev Disabled To enable reverse operation, program with A166
[Reverse Disable].
Program with P036 [Start Source].
P036,P037,
A166
04 Digital Common – For digital inputs. Tied to I/O Terminal 09.
Electronically isolated with digital inputs from analog I/O
and opto output.
05 Digital Input 1 Purge (2)
Program with T051 [Digital In1 Sel]. T051
06 Digital Input 2 Local Program with T052 [Digital In2 Sel]. T052
07 Digital Input 3 Clear Fault Program with T053 [Digital In3 Sel]. T053
08 Digital Input 4 Comm Port Program with T054 [Digital In4 Sel]. T054
09 Digital Common – For digital inputs. Tied to I/O Terminal 04.
Electronically isolated with digital inputs from analog I/O
and opto output.
10 Opto Common – For opto-coupled outputs. Electronically isolated with
opto output from analog I/O and digital inputs.
11 +24V DC – Drive supplied power for digital inputs.
Referenced to Digital Common. Max. Output: 100mA.
12 +10V DC – Drive supplied power for 0-10V external potentiometer.
Referenced to Analog Common. Max. Output: 15mA.
P038
13 Analog Input 1 0-10V External 0-10V (unipolar), 0-20mA or 4-20mA input
supply or potentiometer wiper. Default input is 0-10V.
For current (mA) input, set AI1 DIP Switch to 20mA.
Program with T069 [Analog In 1 Sel].
Input Impedance: 100k ohm (Voltage Mode)
250 ohm (Current Mode)
T069, T070,
T071, T072
14 Analog Common 1 – Common for Analog Input 1 and Analog Output 1 and 2.
Electrically isolated from digital I/O and opto output.
15 Analog Output 1 OutFreq 0-10 Default analog output is 0-10V.
For current (mA) value, set AO1 DIP Switch to 20mA.
Program with T082 [Analog Out1 Sel].
Maximum Load: 4-20mA = 525 ohm (10.5V)
0-10V = 1k ohm (10mA)
P038,
T051-T054,
A152
16 Analog Output 2 OutCurr 0-10 Default analog output is 0-10V.
For a current (mA) value, set AO2 DIP Switch to 20mA.
Program with T085 [Analog Out2 Sel].
Maximum Load: 4-20mA = 525 ohm (10.5V)
0-10V = 1k ohm (10mA)
T082, T084,
T085, T086,
T087
17 Analog Input 2 0-10V Optically isolated external 0-10V (unipolar), ±10V
(bipolar), 0-20mA or 4-20mA input supply or
potentiometer wiper. Default input is 0-10V.
For current (mA) input, set AI2 DIP Switch to 20mA.
Program with T073 [Analog In 2 Sel].
Input Impedance: 100k ohm (Voltage Mode)
250 ohm (Current Mode)
T073, T074,
T075, T076
18 Analog Common 2 – For Analog Input 2. Electronically isolated from digital I/O
and opto output. With Analog Input 2, provides one fully
isolated analog input channel.
19 Opto Output At Frequency Program with T065 [Opto Out Sel]. T065, T066,
T068
20 RS485 (DSI) Shield – Terminal connected to Safety Ground - PE when using
the RS485 (DSI) Communication Port.
(1) See Footnotes (1) and (4) on previous page.
(2)
See the User Manual for Important information regarding Stop commands and the [Digital Inx Sel] Purge option.
12. English-12 PowerFlex 400 Adjustable Frequency AC Drive Quick Start
Relay Terminal Designations and DIP Switches
Figure 4: User Installed Auxiliary Relay Card (Frames D, E, & F Only)
Important: If using auxiliary motor control, ensure that wiring and parameter
configuration are correct before wiring contactor outputs. All relays
on the Auxiliary Relay Card will energize on power-up by default.
Failure to verify proper wiring and parameter configuration can result
in improper motor operation or drive damage. Refer to Appendix D
for more details.
User Installed Relay Board Terminal Designations
No. Signal Default Description Param.
R1 #1 Relay N.O. Ready/Fault Normally open contact for No. 1 output relay. T055
R2 #1 Relay Common – Common for output relay.
R3 #1 Relay N.C. Ready/Fault Normally closed contact for No. 1 output relay. T055
R4 #2 Relay N.O. Motor Running Normally open contact for No. 2 output relay. T060
R5 #2 Relay Common – Common for output relay.
R6 #2 Relay N.C. Motor Running Normally closed contact for No. 2 output relay. T060
Selection DIP Switches:
Analog Input (AI1 & AI2)
Analog Output (AO1 & AO2)
0-10V Sets analog output to either voltage or current.
Settings must match: AI1 & T069 [Analog In 1 Sel]
AI2 & T073 [Analog In 2 Sel]
AO1 & T082 [Analog Out1 Sel]
AO2 & T085 [Analog Out2 Sel]
Sink/Source DIP Switch Source (SRC) Inputs can be wired as Sink (SNK) or Source (SRC) via DIP
Switch setting.
3A 3B 4A 4B 5A 5B
6A 6B 7A 7B 8A 8B
No. Signal Default Description Param.
3A #3 Relay N.O. Ready/Fault Normally open contact for Number 3 Output Relay R221
3B #3 Relay Common – Common for Number 3 Output Relay
4A #4 Relay N.O. Ready/Fault Normally open contact for Number 4 Output Relay R224
4B #4 Relay Common – Common for Number 4 Output Relay
5A #5 Relay N.O. Ready/Fault Normally open contact for Number 5 Output Relay R227
5B #5 Relay Common – Common for Number 5 Output Relay
6A #6 Relay N.O. Ready/Fault Normally open contact for Number 6 Output Relay R230
6B #6 Relay Common – Common for Number 6 Output Relay
7A #7 Relay N.O. Ready/Fault Normally open contact for Number 7 Output Relay R233
7B #7 Relay Common – Common for Number 7 Output Relay
8A #8 Relay N.O. Ready/Fault Normally open contact for Number 8 Output Relay R236
8B #8 Relay Common – Common for Number 8 Output Relay
13. PowerFlex 400 Adjustable Frequency AC Drive Quick Start English-13
Before Applying Power to the Drive
❏ 1. Confirm that all inputs are connected to the correct terminals and are
secure.
❏ 2. Verify that AC line power at the disconnect device is within the rated
value of the drive.
❏ 3. Verify that any digital control power is 24 volts.
❏ 4. Verify that the Sink (SNK)/Source (SRC) Setup DIP Switch is set to
match your control wiring scheme.
Important: The default control scheme is Source (SRC). The Stop
terminal is jumpered (I/O Terminals 01 and 11) to allow
starting from the keypad. If the control scheme is changed
to Sink (SNK), the jumper must be removed from I/O
Terminals 01 and 11 and installed between I/O Terminals
01 and 04.
❏ 5. Verify that the Stop input is present or the drive will not start.
Important: If I/O Terminal 01 is used as a stop input, the jumper
between I/O Terminals 01 and 11 must be removed.
❏ 6. Verify that the Analog I/O DIP Switches are set to 10 volts.
Applying Power to the Drive
❏ 7. Apply AC power and control voltages to the drive.
❏ 8. Familiarize yourself with the integral keypad features before setting
any Program Group parameters.
Start, Stop, Direction and Speed Control
Factory default parameter values allow the drive to be controlled from
the integral keypad. No programming is required to start, stop, and
control speed directly from the integral keypad.
If a fault appears on power up, refer to page 25 for an explanation of the
fault code. For complete troubleshooting information, refer to the
PowerFlex 400 User Manual supplied with the drive.
Prepare For Drive Start-Up
!
ATTENTION: Power must be applied to the drive to perform the
following start-up procedures. Some of the voltages present are at
incoming line potential. To avoid electric shock hazard or damage to
equipment, only qualified service personnel should perform the
following procedure. Thoroughly read and understand the procedure
before beginning. If an event does not occur while performing this
procedure, Do Not Proceed. Remove All Power including user
supplied control voltages. User supplied voltages may exist even when
main AC power is not applied to the drive. Correct the malfunction
before continuing.
14. English-14 PowerFlex 400 Adjustable Frequency AC Drive Quick Start
Operator Keys
Intergral Keypad
Key Name Description
Escape Back one step in programming menu.
Cancel a change to a parameter value and exit Program
Mode.
Select Advance one step in programming menu.
Select a digit when viewing parameter value.
Up Arrow
Down Arrow
Scroll through groups and parameters.
Increase/decrease the value of a flashing digit.
Enter Advance one step in programming menu.
Save a change to a parameter value.
Digital Speed
Increment and
Decrement Arrows
Used to control speed of drive. Default is active.
Control is activated by parameter P038 [Speed Reference] or
P042 [Auto Mode].
Run/Start & Hand (1)
Used to start the drive. Default is Hand mode as controlled by
parameter P042 [Auto Mode].
Control is activated by parameter P036 [Start Source] or
P042 [Auto Mode].
Auto (1)
Used to select Auto control mode.
Controlled by parameter P042 [Auto Mode].
Stop/Off Used to stop the drive or clear a fault.
This key is always active.
Controlled by parameter P037 [Stop Mode].
(1)
Important: Certain digital input settings can override drive operation. Refer to the PowerFlex 400
User Manual for details.
15. PowerFlex 400 Adjustable Frequency AC Drive Quick Start English-15
LED Status Indicators
LCD Display
LED LED State Description
Program Status Steady Red Indicates parameter value can be changed.
Selected digit will flash.
Fault Status Flashing Red Indicates that the drive is faulted.
Speed Status Steady Green Indicates that the digital speed control keys are
enabled.
Hand Status Steady Green Indicates that the Run/Start key is enabled.
Auto Status Steady Yellow Indicates that the drive is in Auto mode.
No. Description
➊ Parameter Name
➋ Run/Stop Status: = Stopped / = Running
flashes to indicate that the drive is stopping, but is still decelerating.
flashes when DC Injection is commanded.
Direction Indication: The Direction Arrow indicates the commanded direction of
rotation. If the Arrow is flashing, the drive has been commanded to change direction, but is still
decelerating.
Sleep Mode Indication: flashes to indicate that the drive is in sleep mode.
➌ Parameter Group and Number:
= Basic Display = Basic Program = Terminal Block
= Communications = Advanced Program = Aux Relay Card
= Advanced Display
➍ Fault Indication and Fault Number
➎ Fault Name
➊
➋ ➌
➍
➎
16. English-16 PowerFlex 400 Adjustable Frequency AC Drive Quick Start
Parameter P042 [Auto Mode] defines the operation mode of the control
keys on the integral keypad. Hand-Off-Auto is the default operation
mode for PowerFlex 400 drives. For detailed information on other
operation modes, refer to the PowerFlex 400 User Manual supplied with
the drive.
Hand-Off-Auto Mode
In HAND mode:
• Control keys operate as Hand-Off-Auto.
• Start command and speed reference come from the integral keypad
Start/Hand and Digital Speed Increment and Decrement keys.
• Auto key switches control from HAND mode to AUTO mode in a
bumpless transfer as long as there is an active Run command.
In AUTO mode:
• Auto key LED is illuminated.
• Start command is defined by P036 [Start Source].
• Speed Reference command is defined by P038 [Speed Reference].
• Start/Hand key switches control to the integral keypad in a bumpless
transfer and switches the speed reference to the integral keypad.
• Stop key stops the drive and the drive switches to HAND mode.
Table 4.A P042 [Auto Mode] = 1 “Hnd-Off-Auto” (Default)
T051-T054 [Digital Inx Sel] ≠ 2 “Auto Mode” or 3 “Local”
Keypad Hand-Off-Auto Functions
HAND Mode AUTO Mode
Key LED Key Function LED Key Function
On Starts drive.
Runs according to Speed Increment/
Decrement keys.
On Changes to HAND Mode and Starts
drive.
Runs according to Speed Increment/
Decrement keys.
On Changes speed. Off Not active.
Keys are only active if P038 [Speed
Source] = 0 “Drive Pot”.
Off Changes to AUTO Mode. On Not active.
N/A Stops drive. N/A Changes to HAND Mode and Stops
drive.
17. PowerFlex 400 Adjustable Frequency AC Drive Quick Start English-17
The following is an example of basic integral keypad and display functions. This example provides basic
navigation instructions and illustrates how to program the first Basic Program Group parameter.
Viewing and Editing Parameters
Step Key(s) Example Displays
1. When power is applied, the last user-selected
Basic Display Group parameter number is
displayed with flashing characters. The display
then defaults to that parameter’s current value.
(Example shows the value of b001 [Output
Freq] with the drive stopped.)
2. Press the Up Arrow or Down Arrow to scroll
through the Basic Display Group parameters.
(Only in Display Groups)
3. Press Esc once to display the Basic Display
Group parameter number shown on power-up.
The parameter number will flash.
4. Press Esc again to enter the group menu. The
group menu letter will flash.
5. Press the Up Arrow or Down Arrow to scroll
through the group menu (b, P, T, C, A and d).
6. Press Enter or Sel to enter a group. The right
digit of the last viewed parameter in that group
will flash.
7. Press the Up Arrow or Down Arrow to scroll
through the parameters that are in the group.
8. Press Enter or Sel to view the value of a
parameter. If you do not want to edit the value,
press Esc to return to the parameter number.
9. Press Enter or Sel to enter program mode to
edit the parameter value. The right digit will
flash and the Program LED will illuminate if the
parameter can be edited.
10.If desired, press Sel to move from digit to digit
or bit to bit. The digit or bit that you can change
will flash.
11.Press the Up Arrow or Down Arrow to change
the parameter value.
12.Press Esc to cancel a change. The digit will
stop flashing, the previous value is restored and
the Program LED will turn off.
Or
Press Enter to save a change. The digit will stop
flashing and the Program LED will turn off.
13.Press Esc to return to the parameter list.
Continue to press Esc to back out of the
programming menu.
If pressing Esc does not change the display,
then b001 [Output Freq] is displayed. Press
Enter or Sel to enter the last group menu
viewed.
or
or
or
or
or
or
or
18. English-18 PowerFlex 400 Adjustable Frequency AC Drive Quick Start
The Basic Program Group contains the most commonly changed parameters.
The PowerFlex 400 is designed so that start up is simple and efficient. The Program Group
contains the most commonly used parameters.
Basic Display Group Parameters
No. Parameter Min/Max Display/Options
b001 [Output Freq] 0.00/[Maximum Freq] 0.01 Hz
b002 [Commanded Freq] 0.00/[Maximum Freq] 0.01 Hz
b003 [Output Current] 0.0/(Drive Amps × 2) 0.1 Amps
b004 [Output Voltage] 0/510 1 VAC
b005 [DC Bus Voltage] 0/820 1 VDC
b006 [Drive Status] 0/1 (1 = Condition True) Bit 4 Bit 3 Bit 2 Bit 1
Decelerating Accelerating Forward Running
b007 [Fault 1 Code] 0/122 1
b008 [Process Display] 0.00/9999.99 0.01
b010 [Output Power] 0.0/999.9 kW 0.1 kW
b011 [Elapsed MWh] 0/3276.7 MWh 0.1 MWh
b012 [Elapsed Run Time] 0/9999 Hrs 1 = 10 Hrs
b013 [Torque Current] 0.0/(Drive Amps × 2) 0.1 Amps
b014 [Drive Temp] 0/120 degC 1 degC
b015 [Elapsed kWh] 0.0/100.0 kWh 0.1 kWh
Smart Start-Up with Basic Program Group
= Stop drive before changing this parameter.
No. Parameter Min/Max Display/Options Default
P031 [Motor NP Volts] 20/Drive Rated Volts 1 VAC Based on Drive Rating
Set to the motor nameplate rated volts.
P032 [Motor NP Hertz] 15/320 Hz 1 Hz 60 Hz
Set to the motor nameplate rated frequency.
P033 [Motor OL Current] 0.0/(Drive Amps × 2) 0.1 Amps Based on Drive Rating
Set to the maximum allowable motor current.
P034 [Minimum Freq] 0.0/320.0 Hz 0.1 Hz 0.0 Hz
Sets the lowest frequency the drive will output
continuously.
P035 [Maximum Freq] 0.0/320.0 Hz 0.1 Hz 60.0 Hz
Sets the highest frequency the drive will output.
P036 [Start Source] 0/6 0 = “Keypad”
1 = “3-Wire”
2 = “2-Wire”
3 = “2-W Lvl Sens”
4 = “2-W Hi Speed”
5 = “Comm Port”
6 = “2-W Lvl/Enbl”
3
Sets the control scheme used to start the drive
when in Auto/Remote mode.
P037 [Stop Mode] 0/7 0 = “Ramp, CF”(1)
1 = “Coast, CF”(1)
2 = “DC Brake, CF”(1)
3 = “DCBrkAuto,CF”(1)
4 = “Ramp”
5 = “Coast”
6 = “DC Brake”
7 = “DC BrakeAuto”
(1)
Stop input also clears active fault.
0
Active stop mode for all stop sources [e.g. keypad,
run forward (I/O Terminal 02), run reverse (I/O
Terminal 03), RS485 port] except as noted below.
Important: I/O Terminal 01 is always a coast to
stop input except when P036 [Start Source] is set
for “3-Wire” control. When in three wire control, I/O
Terminal 01 is controlled by P037 [Stop Mode].
19. PowerFlex 400 Adjustable Frequency AC Drive Quick Start English-19
P038 [Speed Reference] 0/5 0 = “Drive Keypad”
1 = “InternalFreq”
2 = “Analog In 1”
3 = “Analog In 2”
4 = “Preset Freq”
5 = “Comm Port”
2
Sets the source of the speed reference to the drive.
Important: When T051 – T054 [Digital Inx Sel] is
set to option 1, 2, 3, 4, 5, 8, 14, 15, 16 or 17 and
the digital input is active, or if A152 [PID Ref Sel] is
not set to option 0, the speed reference
commanded by this parameter will be overridden.
Refer to Chapter 1 of the PowerFlex 400 User
Manual for details.
P039 [Accel Time 1] 0.00/600.00 Secs 0.01 Secs 20.00 Secs
Sets the rate of accel for all speed increases.
P040 [Decel Time 1] 0.00/600.00 Secs 0.01 Secs 20.00 Secs
Sets the rate of decel for all speed decreases.
P041 [Reset To Defalts] 0/1 0 = “Ready/Idle”
1 = “Factory Rset”
0
Resets all parameter values to factory defaults.
P042 [Auto Mode] 0/3 0 = “No Function”
1 = “Hnd-Off-Auto”
2 = “Local/Remote”
3 = “Auto/Manual”
1
Determines the operation of the “Auto” key on the
integral keypad.
P043 [Motor OL Ret] 0/1 0 = “Disabled”
1 = “Enabled”
0 = “Disabled”
Enables/disables the Motor Overload Retention
function.
= Stop drive before changing this parameter.
No. Parameter Min/Max Display/Options Default
Terminal Block Group Parameters
No. Parameter Min/Max Display/Options Default
T051
T052
T053
T054
[Digital In1 Sel]
I/O Terminal 05
[Digital In2 Sel]
I/O Terminal 06
[Digital In3 Sel]
I/O Terminal 07
[Digital In4 Sel]
I/O Terminal 08
0/36 0 = “Not Used”
1 = “Purge”
2 = “Auto Mode”
3 = “Local”
4 = “Comm Port”
5 = “PID Disable”
6 = “PID Hold”
7 = “PID Reset”
8 = “Preset Freq”
9 = “Aux Fault”
10 = “Clear Fault”
11 = “RampStop,CF”
12 = “CoastStop,CF”
13 = “DCInjStop,CF”
14 = “Anlg1 InCtrl”
15 = “Anlg2 InCtrl”
16 = “MOP Up”
17 = “MOP Down”
18 = “Acc & Dec 2”
19 = “Current Lmt2”
20 = “Force DC”
21 = “Mtr I-Lock 1”
22 = “Mtr I-Lock 2”
23 = “Mtr I-Lock 3”
24 = “Mtr I-Lock 4”
25 = “Cmd Reverse”
31 = “Logic In 1”
32 = “Logic In 2”
36 = “Damper Input”
1
3
10
4
T055
T060
[Relay Out1 Sel]
[Relay Out2 Sel]
0/23 0 = “Ready/Fault”
1 = “At Frequency”
2 = “MotorRunning”
3 = “Hand Active”
4 = “Motor Overld”
5 = “Ramp Reg”
6 = “Above Freq”
7 = “Above Cur”
8 = “Above DCVolt”
9 = “Above Anlg 2”
10 = “Above PF Ang”
11 = “Anlg In Loss”
12 = “ParamControl”
13 = “Retries Exst”
14 = “NonRec Fault”
15 = “Reverse”
16 = “Logic In 1”
17 = “Logic In 2”
23 = “Aux Motor”
0
2
T056 [Relay Out1 Level] 0.0/9999 0.1 0.0
T058 [Relay 1 On Time] 0.0/600.0 Secs 0.1 Secs 0.0 Secs
T059 [Relay 1 Off Time] 0.0/600.0 Secs 0.1 Secs 0.0 Secs
T061 [Relay Out2 Level] 0.0/9999 0.1 0.0
T063 [Relay 2 On Time] 0.0/600.0 Secs 0.1 Secs 0.0 Secs
T060 Setting T061 Min/Max
6 0/320 Hz
7 0/180%
8 0/815 Volts
9 0/100%
10 1/180 degs
12 0/1
20. English-20 PowerFlex 400 Adjustable Frequency AC Drive Quick Start
T064 [Relay 2 Off Time] 0.0/600.0 Secs 0.1 Secs 0.0 Secs
T065 [Opto Out Sel] 0/17 0 = “Ready/Fault”
1 = “At Frequency”
2 = “MotorRunning”
3 = “Hand Active”
4 = “Motor Overld”
5 = “Ramp Reg”
6 = “Above Freq”
7 = “Above Cur”
8 = “Above DCVolt”
9 = “Above Anlg 2”
10 = “Above PF Anlg”
11 = “Anlg In Loss”
12 = “ParamControl”
13 = “Retries Exst”
14 = “NonRec Fault”
15 = “Reverse”
16 = “Logic In 1”
17 = “Logic In 2”
1
T066 [Opto Out Level] 0.0/9999 0.1 0.0
T068 [Opto Out Logic] 0/1 1 0
T069 [Analog In 1 Sel] 0/6 1 2
T070
T074
[Analog In 1 Lo]
[Analog In 2 Lo]
0.0/100.0% 0.1% 0.0%
T071
T075
[Analog In 1 Hi]
[Analog in 2 Hi]
0.0/100.0% 0.1% 100.0%
T072
T076
[Analog In 1 Loss]
[Analog In 2 Loss]
0/6 0 = “Disabled”
1 = “Fault (F29)”
2 = “Stop”
3 = “Zero Ref”
4 = “Min Freq Ref”
5 = “Max Freq Ref”
6 = “Int Freq Ref”
0
T073 [Analog In 2 Sel] 0/7 1 2
T077 [Sleep-Wake Sel] 0/3 0 = “Disabled”
1 = “Analog In 1”
2 = “Analog In 2”
3 = “Command Freq”
0
T078 [Sleep Level] 0.0/100.0% 0.1% 10.0%
T079 [Sleep Time] 0.0/600.0 Secs 0.1 Secs 0.0 Secs
T080 [Wake Level] 0.0/100.0% 0.1% 15.0%
T081 [Wake Time] 0.0/600.0 Secs 0.1 Secs 0.0 Secs
No. Parameter Min/Max Display/Options Default
T065 Setting T066 Min/Max
6 0/400 Hz
7 0/180%
8 0/815 Volts
9 0/100%
10 1/180 degs
12 0/1
T068 Option Opto Out Logic
0 NO (Normally Open)
1 NC (Normally Closed)
T069 Option Setting Input Range DIP Switch AI1 Setting
0 Current Mode 0-20 mA 0-10V
1 Current Mode 4-20 mA 0-10V
2 Voltage Mode - Unipolar 0-10V 0-10V
4 Current Mode (Square Root) 0-20 mA 0-10V
5 Current Mode (Square Root) 4-20 mA 0-10V
6 Voltage Mode - Unipolar (Square Root) 0-10V 0-20 mA
T073 Option Setting Input Range DIP Switch AI1 Setting
0 Current Mode 0-20 mA 20 mA
1 Current Mode 4-20 mA 20 mA
2 Voltage Mode - Unipolar 0-10V 10V
3 Voltage Mode - Bipolar -10 to +10V 10V
4 Current Mode (Square Root) 0-20 mA 20 mA
5 Current Mode (Square Root) 4-20 mA 20 mA
6 Voltage Mode - Unipolar (Square Root) 0-10V 10V
7 Voltage Mode - Bipolar (Square Root) -10 to +10V 10V
21. PowerFlex 400 Adjustable Frequency AC Drive Quick Start English-21
T082
T085
[Analog Out1 Sel]
[Analog Out2 Sel]
0/20 1 0
1
T083
T086
[Analog Out1 High]
[Analog Out2 High]
0/800% 1% 100%
T084
T087
[Anlg Out1 Setpt]
[Anlg Out2 Setpt]
0.0/100.0% 0.1% 0.0%
T088 [Anlg Loss Delay] 0.0/20.0 Secs 0.1 Secs 0.0 Secs
No. Parameter Min/Max Display/Options Default
Setting
Output
Range
Min. Output
Value Max. Output Value Filter
DIP Switch
AO1
Related
Parameter
0 OutFreq 0-10 0-10V 0V = 0 Hz [Maximum Frequency] None 10V b001
1 OutCurr 0-10 0-10V 0V = 0 Amps 200% Drive Rated FLA Filter A 10V b003
2 OutTorq 0-10 0-10V 0V = 0 Amps 200% Drive Rated FLA Filter A 10V b013
3 OutVolt 0-10 0-10V 0V = 0 Volts 120% Drive Rated Output V None 10V b004
4 OutPowr 0-10 0-10V 0V = 0 kW 200% Drive Rated Power Filter A 10V b010
5 Setpnt 0-10 0-10V 0V = 0.0% 100.0% Setting None 10V T084
6 TstData 0-10 0-10V 0V = 0000 65535 (Hex FFFF) None 10V A196
7 OutFreq 0-20 0-20 mA 0 mA = 0 Hz [Maximum Frequency] None 20 mA b001
8 OutCurr 0-20 0-20 mA 0 mA = 0 Amps 200% Drive Rated FLA Filter A 20 mA b003
9 OutTorq 0-20 0-20 mA 0 mA = 0 Amps 200% Drive Rated FLA Filter A 20 mA b013
10 OutVolt 0-20 0-20 mA 0 mA = 0 Volts 120% Drive Rated Output V None 20 mA b004
11 OutPowr 0-20 0-20 mA 0 mA = 0 kW 200% Drive Rated Power Filter A 20 mA b010
12 Setpnt 0-20 0-20 mA 0 mA = 0.0% 100.0% Setting None 20 mA T084
13 TstData 0-20 0-20 mA 0 mA = 0000 65535 (Hex FFFF) None 20 mA A196
14 OutFreq 4-20 4-20 mA 4 mA = 0 Hz [Maximum Frequency] None 20 mA b001
15 OutCurr 4-20 4-20 mA 4 mA = 0 Amps 200% Drive Rated FLA Filter A 20 mA b003
16 OutTorq 4-20 4-20 mA 4 mA = 0 Amps 200% Drive Rated FLA Filter A 20 mA b013
17 OutVolt 4-20 4-20 mA 4 mA = 0 Volts 120% Drive Rated Output V None 20 mA b004
18 OutPowr 4-20 4-20 mA 4 mA = 0 kW 200% Drive Rated Power Filter A 20 mA b010
19 Setpnt 4-20 4-20 mA 4 mA = 0.0% 100.0% Setting None 20 mA T084
20 TstData 4-20 4-20 mA 4 mA = 0000 65535 (Hex FFFF) None 20 mA A196
T083 Setting T082 Setting T082 Max. Output Value
50% 1 “OutCurr 0-10” 5V for 200% Drive Rated Output Current
90% 11 “OutPowr 0-20” 18 mA for 200% Drive Rated Power
Communications Group Parameters
No. Parameter Min/Max Display/Options Default
C101 [Language] 1/10 1 = “English”
2 = “Français”
3 = “Español”
4 = “Italiano”
5 = “Deutsch”
6 = “Reserved”
7 = “Português”
8 = “Reserved”
9 = “Reserved”
10 = “Nederlands”
1
C102 [Comm Format] 0/9 0 = “RTU 8-N-1”
1 = “RTU 8-E-1”
2 = “RTU 8-O-1”
3 = “RTU 8-N-2”
4 = “RTU 8-E-2”
5 = “RTU 8-O-2”
6 = “MetaSys N2”
7 = “P1 8-N-1”
8 = “P1 8-E-1”
9 = “P1 8-O-1”
0
Power to drive must be cycled before any
changes will affect drive operation.
C103 [Comm Data Rate] 0/5 0 = “1200”
1 = “2400”
2 = “4800”
3 = “9600”
4 = “19.2K”
5 = “38.4K”
0
C104 [Comm Node Addr] 1/247 1 100
C105 [Comm Loss Action] 0/5 0 = “Fault”
1 = “Coast Stop”
2 = “Stop”
3 = “Continu Last”
4 = “Run Preset 0”
5 = “Kypd Inc/Dec”
0
C106 [Comm Loss Time] 0.1/60.0 Secs 0.1 Secs 5.0 Secs
C107 [Comm Write Mode] 0/1 0 = “Save” 1 = “RAM Only” 0
C108 [Start Source 2] 0/6 0 = “Keypad”
1 = “3-Wire”
2 = “2-Wire”
3 = “2-W Lvl Sens”
4 = “2-W Hi Speed”
5 = “Comm Port”
6 = “2-W Lvl/Enbl”
3
Sets the control scheme used to start the drive
when in Auto/Remote mode.
C109 [Speed Ref 2] 0/5 0 = “Drive Keypad”
1 = “InternalFreq”
2 = “Analog In 1”
3 = “Analog In 2”
4 = “Preset Freq”
5 = “Comm Port”
2
24. English-24 PowerFlex 400 Adjustable Frequency AC Drive Quick Start
R242
R245
R248
[Aux 1 Stop Freq]
[Aux 2 Stop Freq]
[Aux 3 Stop Freq]
0.0/320.0 Hz 0.1 Hz 25.0 Hz
R243
R246
R249
[Aux 1 Ref Add]
[Aux 2 Ref Add]
[Aux 3 Ref Add]
0.0/100.0% 0.1% 0.0%
R250 [Aux Start Delay] 0.0/999.9 Secs 0.1 Secs 5.0 Secs
R251 [Aux Stop Delay] 0.0/999.9 Secs 0.1 Secs 3.0 Secs
R252 [Aux Prog Delay] 0.00/60.00 Secs 0.01 Secs 0.50 Secs
R253 [Aux AutoSwap Tme] 0.0/999.9 Hrs 0.1 Hrs 0.0 Hr
R254 [Aux AutoSwap Lvl] 0.0/100.0% 0.1% 50.0%
No. Parameter Min/Max Display/Options Default
Advanced Display Group Parameters
No. Parameter Min/Max Display/Options Default
d301 [Control Source] 0/99 Digit 0: Start Command
0 = Keypad
1 = Terminal Block
2 = Communications
Digit 1: Speed Command
0 = Local Keypad Pot
1 = A142
2 = Analog Input 1
3 = Analog Input 2
4 = A143-146
5 = Communications
Read Only
d302 [Control In Status] 0/1
(1 = Condition True)
Read Only
d303 [Comm Status] 0/1
(1 = Condition True)
Digit 0: Received Good Message Packet
Digit 1: Transmitting Message
Digit 2: DSI Peripheral Connected
Digit 3: Received Bad Message Packet
Read Only
d304 [PID Setpnt Displ] 0.0/100.0% 0.1% 0.0%
d305
d306
[Analog In 1]
[Analog In 2]
0.0/120.0% 0.1% 0.0%
d307
d308
d309
[Fault 1 Code]
[Fault 2 Code]
[Fault 3 Code]
0/122 1 Read Only
d310
d312
d314
[Fault 1 Time-hr]
[Fault 2 Time-hr]
[Fault 3 Time-hr]
0/9999 Hrs 1 Hrs Read Only
d311
d313
d315
[Fault 1 Time-min]
[Fault 2 Time-min]
[Fault 3 Time-min]
0.0/60.0 Min 0.1 Min Read Only
d316 [Elapsed Time-hr] 0/32767 1 Hr Read Only
d317 [Elapsed Time-min] 0.0/60.0 Min 0.1 Min Read Only
d318 [Output Powr Fctr] 0.0/180.0 deg 0.1 deg Read Only
d319 [Testpoint Data] 0/FFFF 1 Hex Read Only
d320 [Control SW Ver] 1.00/99.99 0.01 Read Only
d321 [Drive Type] Used by Rockwell Automation field service personnel.
d322 [Output Speed] 0.0/100.0% 0.1% Read Only
d323 [Output RPM] 0/24000 RPM 1 RPM Read Only
d324 [Fault Frequency] 0.00/320.00 Hz 0.01 Hz Read Only
d325 [Fault Current] 0.0/(Drive Amps × 2) 0.1 Amps Read Only
d326 [Fault Bus Volts] 0/820 VDC 1 VDC Read Only
d327 [Status @ Fault] 0/1 1 Read Only
Display Digit (Right to Left) I/O Terminal Control Input
0 02 Start/FWD In
1 03 Dir/Rev In
2 01 Stop Input
3 05 Digital In 1
4 06 Digital In 2
5 07 Digital In 3
6 08 Digital In 4
25. PowerFlex 400 Adjustable Frequency AC Drive Quick Start English-25
To clear a fault, press the Stop key, cycle power or set A100 [Fault Clear] to 1 or
2.
For a complete listing of Faults and Alarms, refer to the PowerFlex 400
User Manual.
Fault Codes
No. Fault Description
F2 Auxiliary Input(1)
Check remote wiring.
F3 Power Loss Monitor the incoming AC line for low voltage or line power interruption.
F4 UnderVoltage(1)
Monitor the incoming AC line for low voltage or line power interruption.
F5 OverVoltage(1)
Monitor the AC line for high line voltage or transient conditions. Bus overvoltage can also be
caused by motor regeneration. Extend the decel time or install a dynamic brake chopper.
F6 Motor Stalled(1)
Increase [Accel Time x] or reduce load so drive output current does not exceed the current set
by parameter A089 [Current Limit].
F7 Motor Overload(1) An excessive motor load exists. Reduce load so drive output current does not exceed the
current set by parameter P033 [Motor OL Current].
F8 Heatsink OvrTmp(1)
Check for blocked or dirty heat sink fins. Verify that ambient temperature has not exceeded 40°C
(104°F)forIP30/NEMA1/ULType1installationsor50°C(122°F)forOpentypeinstallations.
Check fan.
F12 HW OverCurrent Check programming. Check for excess load, improper DC boost setting, DC brake volts set too
high or other causes of excess current.
F13 Ground Fault Check the motor and external wiring to the drive output terminals for a grounded condition.
F15 Load Loss Check for load loss (i.e., a broken belt).
F29 Analog Input Loss(1)
An analog input is configured to fault on signal loss. A signal loss has occurred.
F33 Auto Rstrt Tries Correct the cause of the fault and manually clear.
F38 Phase U to Gnd Check the wiring between the drive and motor. Check motor for grounded phase.
Replace drive if fault cannot be cleared.F39 Phase V to Gnd
F40 Phase W to Gnd
F41 Phase UV Short Check the motor and drive output terminal wiring for a shorted condition.
Replace drive if fault cannot be cleared.F42 Phase UW Short
F43 Phase VW Short
F48 Params Defaulted The drive was commanded to write default values to EEPROM. Clear the fault or cycle power to
the drive. Program the drive parameters as needed.
F63 SW OverCurrent(1) Check load requirements and A098 [SW Current Trip] setting.
F64 Drive Overload Reduce load or extend Accel Time.
F70 Power Unit Cycle power. Replace drive if fault cannot be cleared.
F71 Net Loss The communication network has faulted.
F81 Comm Loss If adapter was not intentionally disconnected, check wiring to the port. Replace wiring, port
expander, adapters or complete drive as required. Check connection. An adapter was
intentionally disconnected. Turn off using C105 [Comm Loss Action].
F94 Function Loss Close input to terminal 01 and re-start the drive.
F100 Parameter Checksum Restore factory defaults.
F122 I/O Board Fail Cycle power. Replace drive if fault cannot be cleared.
(1)
Auto-Reset/Run type fault. Configure with parameters A092 and A093.
26. English-26 PowerFlex 400 Adjustable Frequency AC Drive Quick Start
PowerFlex 400 Frames
Figure 5: PowerFlex 400 Frames C-F
Dimensions are in millimeters and (inches).
EMC Line Filters
Figure 6: Catalog Numbers: 22-RF018-CS, 22-RF018-CL, 22-RF026-CS,
22-RF026-CL, 22-RF026-CL, 22-RF034-CS
Dimensions
Output Power Frame Size
kW HP 208-240V ACInput 400-480V AC Input
2.2-7.5 3-10 C C
11-15 15-20 D C
18.5-22 25-30 D D
30-37 40-50 E E
45-75 60-100 – E
90-110 125-150 – F
A
E
B
D
F 105.8
(4.17)
24.5
(0.96)
138.2
(5.44)
C 244
(9.61)
300
(11.81)
325
(12.8)
IP20/66 (NEMA Type 1/4X/12) Flange Mount
Frame A B C D E F
Weight (1)
kg (lbs.)
C 130.0 (5.1) 260.0 (10.2) 180.0 (7.1) 116.0 (4.57) 246.0 (9.7) 5.8 (0.23) 4.33 (9.5)
D 250.0 (9.84) 436.2 (17.17) 206.1 (8.11) 226.0 (8.90) 383.4 (15.09) 9.0 (0.35) 14.0 (30.9)
E 370.0 (14.57) 605.5 (23.84) 259.2 (10.21) 335.0 (13.19) 567.4 (22.34) 8.5 (0.33) 51.2 (112.9)
F 425.0 (16.73) 850.0 (33.46) 264.0 (10.39) 381.0 (15.00) 647.5 (25.49) 13.0 (0.51) 88.0 (194.0)
(1) Weights include HIM and Standard I/O.
130
(5.12)90
(3.54)
60
(2.36)32
(1.26)
17
(0.67) 30
(1.18)
5.5 (0.22)
297
(11.69) 297
(11.69)
309
(12.17)
27. PowerFlex 400 Adjustable Frequency AC Drive Quick Start English-27
Figure 7: Catalog Numbers: 22-RFD036, 22-RFD050, 22-RFD070, 22-RFD100,
22-RFD150, 22-RFD180
Dimensions are in millimeters and (inches).
Figure 8: Catalog Numbers: 22-RFD330
Catalog
Number A B C D E F G
22-RFD036 74 (2.91) 272 (10.71) 161 (6.34) 60 (2.36) 258 (10.16) 7.5 (0.30) 7 (0.28)
22-RFD050 93 (3.66) 312 (12.28) 190 (7.48) 79 (3.11) 298 (11.73) 13.5 (0.53) 7 (0.28)
22-RFD070 93 (3.66) 312 (12.28) 190 (7.48) 79 (3.11) 298 (11.73) 13.5 (0.53) 7 (0.28)
22-RFD100 93 (3.66) 312 (12.28) 190 (7.48) 79 (3.11) 298 (11.73) 13.5 (0.53) 7 (0.28)
22-RFD150 126 (4.96) 312 (12.28) 224 (8.82) 112 (4.41) 298 (11.73) 19.5 (0.77) 7 (0.28)
22-RFD180 126 (4.96) 312 (12.28) 224 (8.82) 112 (4.41) 298 (11.73) 27 (1.06) 7 (0.28)
B
E
A
D C
F
G
235
(9.25)
120
(4.72)
65
(2.56)
65
(2.56)
∅ 12
(2.56)
∅ 10.5
(2.56)
68
(2.68)
40
(1.57)
15
(0.59)
306
(12.05)
55
(2.17)386
(15.20)
25
(0.98)120
(4.72)