The document discusses the design of emergency relief systems for exothermic batch reactors. It covers key components of a relief system including pressure relief devices, piping and headers, containment systems, and treatment systems. It also discusses models for sizing relief devices, including vessel and vent flow models as well as heat models. The CHEMCAD software is identified as a useful tool for designing relief systems and sizing relief devices.
Report
Share
Report
Share
1 of 35
More Related Content
Relief and blowdown in
1. RELIEF AND BLOWDOWN
IN
BATCH PROCESSES
A SEMINAR ON
AKSHAY .S. KOTKAR GUIDED BY
M.TECH IN CHEM.ENG DR. S.P .SHIRSATH
L.I.T, NAGPUR L .I.T , NAGPUR
2. CONTENTS
1. INTRODUCTION
2. RELIEF SYSTEM LAYOUT
2.1 Pressure Relief Devices
2.2 Relief System Piping And headers
2.3 Containment System
2.4 Treatment System
3. RELIEF SYSTEM SIZING
3.1 Design Fundamentals
3.2 Vessel And Vent Flow Models
3.3 Heat Models
3.4 CHEMCAD Utility – Relief Device Sizing
4. RELIEF SYSTEM HEADER
3. INTRODUCTION
To achieve safe operation of chemical reactors processing
exothermic reactions requires a combination of Preventative and
Protective Measures.
This seminar reviews the techniques associated with emergency
pressure relief and the value of CHEMCAD as a design tool in this
important area of Process Engineering.
4. Preventative Measures include:
• Automatic control systems including the use of an independent
hardwired alarm and trip system.
• Provision for appropriate manual intervention.
Protective Measures mitigate the consequences of a runaway
reaction and include:
• Emergency pressure relief.
• Crash cooling.
• Reaction inhibition.
• Drown out.
5. ADVANTAGES OF PRESSURE RELIEF SYSTEM
• Different and independent failure modes to the preventative
measures.
• Provides relatively passive means of protection.
• Provides adequate protection if all other systems fail.
The emergency pressure relief system is considered the ultimate
protection. The primary basis of safety for overpressure protection is
based on prevention involving management control procedures and
instrument protective systems.
Emergency pressure relief may not be appropriate due to
economical, environmental or technical considerations. In such
cases, appropriate preventative measures must be relied on.
6. DESIGN OF EMERGENCY RELIEF SYSTEM
The design of emergency relief systems for exothermic batch
reactors requires a thorough understanding of the reaction
conditions including:
• The credible maloperations and system failures that might occur
during reaction.
• The kinetics of the reaction under runaway conditions.
• Whether the reaction pressure is from vapour, gas or both.
• The flow regimes in the vessel and relief system during relief.
• The design and layout of the relief system.
8. The emergency relief system comprises certain key
components:
• Primary pressure relief device.
• Relief system piping and headers.
• Containment system.
• Treatment system.
9. PRESSURE RELIEF DEVICES
The pressure relief device is either a relief valve, a bursting disc or a
combination of the two.
On chemical reactors the bursting (rupture) disc is most favoured
due to being able to handle the following conditions:
• Rapid pressure rise with full relief area available.
• Toxic fluids where no leakage past a safety valve is permitted.
• Corrosive fluids that may cause progressive deterioration of a
safety valve.
• Fluids that may deposit solids or gums that interfere with safety
valve operation.
10. The major disadvantages of bursting discs are as follows:
• Require a larger allowance between the operating and the set
pressure
.
• If the operating and the set pressures are too close, the disc can fail
prematurely due to pressure pulsations.
• Loss of containment of reactor contents on operation i.e. valve does
not reseat.
11. The relief pressure at which the relief device is fully open should be
set at the lowest pressure practicable consistent with preventing
nuisance operations. The reasons for this are:
• For most exothermic runaway reactions, the reaction rate and heat
release rate increases exponentially with temperature. For a vapour
pressure system, a low relief pressure means a low relief
temperature and hence a relatively low rate of heat release. The
relief area required is directly proportional to the rate of heat release
by the reaction.
• For a relief system venting a two-phase mixture, pressure relief
acts to remove reactants from the reactor. A low relief pressure
allows a greater margin between the relief pressure and maximum
permitted pressure, and advantage is taken of this by the sizing
methods to yield a smaller relief area.
12. DESIGN OF RELIEF SYSTEM SIZING
The requirements for the design of the relief system sizing can be
summarised:
• The equipment design pressure plus permitted accumulation is no
exceeded.
• The pressure relief system is as small as possible consistent with
the above clause. A small relief system minimises cost, disposal
requirements and the potential rate at which material could be
discharged to the environment.
14. RELIEF SYSTEM PIPING AND HEADERS
The flow capacity of a bursting disc is determined by the piping
system rather than by the disc itself.
Key features of the relief system piping design can be summarised:
• Branch pipe from reactor to the header to be not less than the
outlet diameter of relief device.
• Branch pipe to enter main header as a 45 degree T, flow through
branch.
• All 90° bends to have maximum R/D consistent with layout
constraints.
• Main header to slope towards the blowdown drum and enter
tangentially.
15. • Consideration to be given to nitrogen inerting to prevent explosive
mixtures.
• Provision of adequate inspection and test facilities to ensure
headers are clear.
16. LAYOUT OF RELIEF SYSTEM
CONTAINMENT SYSTEM :
In many instances the discharge stream from an emergency relief
system is a two-phase vapour liquid mixture. The stream is routed to
a blowdown/knock out drum designed to disentrain the liquid from
the vapour to allow discharge to atmosphere or for downstream
treatment. The justification for the blowdown drum is:
• Prevents release of hot, toxic and corrosive liquid resulting in
potential safety hazards and environmental damage.
• Prevents release of flammable droplets leading to vapour cloud
explosion.
• Allows downstream treatment of toxic vapours for treatment in a
wet scrubber, flare or incinerator.
17. There are many designs of blowdown drum depending upon the
circumstances but key features include:
• Tangential inlet into a vessel of sufficient diameter to effect good
vapour – liquid separation.
• Total volume sufficient to hold the estimated carryover, typically
two times the volume of the largest reactor connected to the relief
system.
• Adequate instrumentation monitoring for level and pressure
detection.
• Appropriate facilities for drainage and material handling.
• Appropriate facilities for quenching reaction mixtures.
18. TREATMENT SYSTEM
Vapours vented from exothermic reactions are normally treated by
contacting with a scrubbing liquor to provide fast chemical
reaction. The vapours are contacted in a random packed tower with
suitable hydraulic design parameters and packed height for mass
transfer/reaction.
CHEMCAD in conjunction with Excel provides a powerful design
tool for this process. The following key features of design are:
• Tower diameter, packing selection and hydraulics determined
from SCDS UnitOp and CHEMCAD Equipment Sizing –
packing SCDS configuration for an absorber is used with
condenser Mode 0 and Reboiler Mode 0.
19. • Packed height is determined from model in Excel Unit Op on the
SCDS inlet.
• Fast chemical reaction involves an exotherm and CHEMCAD is
used to carryout the thermal design of the system which involves
ensuring adequate circulating liquor volume and flow with
adequately sized heat exchanger to control system temperature.
• Atmospheric dispersion is determined from model in Excel UnitOp
on the SCDS outlet.
Column hydraulics design involves:
• Ensuring adequate liquor circulation flow to satisfy minimum
wetting rate for the packing.
•Packing adequately loaded (liquid/gas ratio) for mass transfer.
20. Column loading should not exceed 80% flood this may have to be
achieved by limiting the vapour rate with a restriction orifice in the
blowdown tank vent line sized using CHEMCAD Equipment
Sizing Orifice.
21. RELIEF SYSTEM SIZING :
DESIGN FUNDAMENTALS
VENT AND VENT FLOW MODELS :
In relief system design there are three main types of system to be
considered depending on the nature of the reaction.
• Vapour pressure systems
The pressure generated by a runaway reaction is entirely due to the
vapour pressure of the reacting mixture, which rises as the
temperature of the mixture increases during a thermal
runaway.
• Gassy systems
The pressure generated by a runaway reaction is entirely due to a
permanent gas which is evolved by the chemical reaction.
22. • Hybrid systems
The pressure is due to both the evolution of a permanent gas and
increasing vapour pressure with increasing temperature.
Vapour pressure systems are tempered in that the temperature
and reaction rate is controlled during relief due to latent heat
removal.
Gassy systems are untempered in that pressure relief does not
control the temperature or reaction rate.
24. VESSEL FLOW REGIMES
The two-phase flow regime within the venting vessel will influence
the fraction of gas or vapour within this two-phase mixture. The
vessel flow regimes considered are:
25. Level swell, depending on reactor level, results in venting of a two-
phase mixture typical of gassy and hybrid systems.
Foamy systems invariably will vent a two-phase mixture throughout
the relief period.
Two phase flow models for Relief Device Sizing to be considered
are:
• Homogeneous equilibrium model (HEM)
Assumes uniform mixing of phases across the pipe section – no
phase slip, thermal equilibrium, and vapour/liquid equilibrium.
(Recommended by DIERS).
• Equilibrium rate model (ERM)
Assumes no flashing in the relief system until the choke point and
then flashing at equilibrium rate at the choke point.
26. • Henry Fauske model (HNE)
Neglects friction and assumes two-phase relief system flow is not
choked which is less conservative.
28. The vessel and vent flow models should be established
experimentally. The following assumptions are considered
conservative (safe):
• For tempered systems
Two-phase rather than vapour relief.
Homogeneous vessel behaviour.
Homogeneous equilibrium model (HEM) for relief system flow.
• For untempered systems
Two phase relief at the point of maximum gas generation rate.
Level swell behaviour in the reactor which minimises early loss of
reactants by relief e.g. churn turbulent.
Homogeneous equilibrium model for relief system flow.
29. HEAT MODELS
For relief device sizing from exothermic reactions experimental data
is required from reaction screening techniques to establish the
maximum rate of pressure rise and maximum rate of temperature
rise.
Heat input rates can be user defined from a knowledge of the
thermal characteristics of the reaction system and associated jacket
services. This is particularly useful when considering operational
and control system failure modes such as maximum heat input from
jacket systems.
Heat input rates can also be as a result of external fire.
30. CHEMCAD UTILITY:RELIEF SYSTEM
SIZING
The relief device sizing Utility is a comprehensive module giving
consideration to all the relevant design fundamentals.
To use the module the following procedure has been applied:
• Prepare the vessel design parameters input data table .
diameter, cylinder length, dished end depth ratio (h/R), liquid level.
• Prepare process parameters input data table .
components, charge details weight and mole fractions.
• Define component list and thermodynamics.
For common organic solvent based systems.
Equilibrium K Ideal Vapour Pressure.
Enthalpy H SRK or Latent Heat.
31. • Set up Flow Sheet with Reactor Inputs and Vent Manifold using
Pipe Simulator UnitOp.
• Define stream compositions. Set vapour mole fraction and stream
pressure at relief device set pressure and flash to obtain temperature.
• Complete Relief Device Sizing entry data.
- Assign relevant Stream Number from Flowsheet.
- Mode Design for new device.
Rating for existing device.
- Device Type including coefficient of discharge from
manufacturer’s data. Caution with bursting discs with vacuum
support.
- Select Vessel Model and Vent Model based on knowledge of
process. Alternatively, use conservative Homogeneous Vessel and
HEM Vent Flow model. For external fire single-phase vapour is
usually appropriate.
32. - Specify Heat Model.
For external fire API 2000 is conservative compared with API
520/521.
API 520/521 with inadequate drainage/fire fighting facilities and
Environmental Factor
F = 1.0 is conservative.
- Valve selection – use calculated size for rating case.
-Complete inlet/outlet piping details.
Results should be printed out for each Stream as completed
33. RELIEF SYSTEM HEADER
•The CHEMCAD Pipe Simulator UnitOp is used to Design and
Rate the relief manifold.
•The vent conditions are available from the relief device sizing runs,
which are now entered into the relevant streams using the relief
temperature, and stream pressures set at 1 bar initially. (i.e. negative
pressure at blowdown tank after first simulation run).
•Isothermal flow conditions are assumed at the relief discharge
temperature. If this was not available the temperature at the relief
device set pressure are taken.
•Actual flow conditions will be between isothermal and adiabatic
conditions. For most cases the more conservative isothermal
conditions are recommended.
34. CONCLUSION
•The techniques associated with emergency pressure relief and the
value of CHEMCAD as a design tool are important in this area of
process Engineering.
• Significant research has been carried out particularly by the Design
Institute for Emergency Relief Systems (DIERS) and a recent
publication in the UK by the Health and Safety Executive Workbook
for Chemical Reactor Relief System Sizing is a useful design tool.
•CHEMCAD Relief Device sizing requires knowledge of the inlet
and outlet piping configuration .
•CHEMCAD in conjunction with Excel provides a powerful design
tool for this process.