-
50 Ohm Transmission Lines with Extreme Wavelength Compression Based on Superconducting Nanowires on High-Permittivity Substrates
Authors:
Daniel F. Santavicca,
Marco Colangelo,
Carleigh R. Eagle,
Maitri P. Warusawithana,
Karl K. Berggren
Abstract:
We demonstrate impedance-matched low-loss transmission lines with a signal wavelength more than 150 times smaller than the free space wavelength using superconducting nanowires on high permittivity substrates. A niobium nitride thin film is patterned in a coplanar waveguide (CPW) transmission line geometry on a bilayer substrate consisting of 100 nm of epitaxial strontium titanate on high-resitivi…
▽ More
We demonstrate impedance-matched low-loss transmission lines with a signal wavelength more than 150 times smaller than the free space wavelength using superconducting nanowires on high permittivity substrates. A niobium nitride thin film is patterned in a coplanar waveguide (CPW) transmission line geometry on a bilayer substrate consisting of 100 nm of epitaxial strontium titanate on high-resitivity silicon. The use of strontium titanate on silicon enables wafer-scale fabrication and maximizes process compatibility. It also makes it possible to realize a $50$ $Ω$ characteristic impedance across a wide range of CPW widths, from the nanoscale to the macroscale. We fabricated and characterized an approximately $50$ $Ω$ CPW device with two half-wave stub resonators. Comparing the measured transmission coefficient to numerical simulations, we determine that the strontium titanate film has a dielectric constant of $1.1 \times 10^3$ and a loss tangent of not more than 0.009. To facilitate the design of distributed microwave devices based on this type of material system, we describe an analytical model of the CPW properties that gives good agreement with both measurements and simulations.
△ Less
Submitted 15 December, 2021; v1 submitted 1 November, 2021;
originally announced November 2021.
-
A compact and tunable forward coupler based on high-impedance superconducting nanowires
Authors:
Marco Colangelo,
Di Zhu,
Daniel F. Santavicca,
Brenden A. Butters,
Joshua C. Bienfang,
Karl K. Berggren
Abstract:
Developing compact, low-dissipation, cryogenic-compatible microwave electronics is essential for scaling up low-temperature quantum computing systems. In this paper, we demonstrate an ultra-compact microwave directional forward coupler based on high-impedance slow-wave superconducting-nanowire transmission lines. The coupling section of the fabricated device has a footprint of…
▽ More
Developing compact, low-dissipation, cryogenic-compatible microwave electronics is essential for scaling up low-temperature quantum computing systems. In this paper, we demonstrate an ultra-compact microwave directional forward coupler based on high-impedance slow-wave superconducting-nanowire transmission lines. The coupling section of the fabricated device has a footprint of $416\,\mathrm{μm^2}$. At 4.753 GHz, the input signal couples equally to the through port and forward-coupling port (50:50) at $-6.7\,\mathrm{dB}$ with $-13.5\,\mathrm{dB}$ isolation. The coupling ratio can be controlled with DC bias current or temperature by exploiting the dependence of the kinetic inductance on these quantities. The material and fabrication-process are suitable for direct integration with superconducting circuits, providing a practical solution to the signal distribution bottlenecks in developing large-scale quantum computers.
△ Less
Submitted 23 November, 2020;
originally announced November 2020.
-
A Single-Photon Imager Based on Microwave Plasmonic Superconducting Nanowire
Authors:
Qing-Yuan Zhao,
Di Zhu,
Niccolò Calandri,
Andrew E. Dane,
Adam N. McCaughan,
Francesco Bellei,
Hao-Zhu Wang,
Daniel F. Santavicca,
Karl K. Berggren
Abstract:
Detecting spatial and temporal information of individual photons by using single-photon-detector (SPD) arrays is critical to applications in spectroscopy, communication, biological imaging, astronomical observation, and quantum-information processing. Among the current SPDs1,detectors based on superconducting nanowires have outstanding performance2, but are limited in their ability to be integrate…
▽ More
Detecting spatial and temporal information of individual photons by using single-photon-detector (SPD) arrays is critical to applications in spectroscopy, communication, biological imaging, astronomical observation, and quantum-information processing. Among the current SPDs1,detectors based on superconducting nanowires have outstanding performance2, but are limited in their ability to be integrated into large scale arrays due to the engineering difficulty of high-bandwidth cryogenic electronic readout3-8. Here, we address this problem by demonstrating a scalable single-photon imager using a single continuous photon-sensitive superconducting nanowire microwave-plasmon transmission line. By appropriately designing the nanowire's local electromagnetic environment so that the nanowire guides microwave plasmons, the propagating voltages signals generated by a photon-detection event were slowed down to ~ 2% of the speed of light. As a result, the time difference between arrivals of the signals at the two ends of the nanowire naturally encoded the position and time of absorption of the photon. Thus, with only two readout lines, we demonstrated that a 19.7-mm-long nanowire meandered across an area of 286 μm * 193 μm was capable of resolving ~590 effective pixels while simultaneously recording the arrival times of photons with a temporal resolution of 50 ps. The nanowire imager presents a scalable approach to realizing high-resolution photon imaging in time and space.
△ Less
Submitted 28 July, 2016; v1 submitted 27 May, 2016;
originally announced May 2016.
-
Microwave dynamics of high aspect ratio superconducting nanowires studied using self-resonance
Authors:
Daniel F. Santavicca,
Jesse K. Adams,
Lierd E. Grant,
Adam N. McCaughan,
Karl K. Berggren
Abstract:
We study the microwave impedance of extremely high aspect ratio (length/width ~ 5,000) superconducting niobium nitride nanowires. The nanowires are fabricated in a compact meander geometry that is in series with the center conductor of a 50 ohm coplanar waveguide transmission line. The transmission coefficient of the sample is measured up to 20 GHz. At high frequency, a peak in the transmission co…
▽ More
We study the microwave impedance of extremely high aspect ratio (length/width ~ 5,000) superconducting niobium nitride nanowires. The nanowires are fabricated in a compact meander geometry that is in series with the center conductor of a 50 ohm coplanar waveguide transmission line. The transmission coefficient of the sample is measured up to 20 GHz. At high frequency, a peak in the transmission coefficient is seen. Numerical simulations show that this is a half-wave resonance along the length of the nanowire, where the nanowire acts as a high impedance, slow wave transmission line. This resonance sets the upper frequency limit for these nanowires as inductive elements. Fitting simulations to the measured resonance enables a precise determination of the nanowire's complex sheet impedance at the resonance frequency. The real part is a measure of dissipation, while the imaginary part is dominated by kinetic inductance. We characterize the dependence of the sheet resistance and sheet inductance on both temperature and current and compare the results to recent theoretical predictions for disordered superconductors. These results can aid in the understanding of high frequency devices based on superconducting nanowires. They may also lead to the development of novel superconducting devices such as ultra-compact resonators and slow-wave structures.
△ Less
Submitted 12 July, 2016; v1 submitted 22 February, 2016;
originally announced February 2016.
-
Terahertz detection mechanism and contact capacitance of individual metallic single-walled carbon nanotubes
Authors:
Joel D. Chudow,
Daniel F. Santavicca,
Chris B. McKitterick,
Daniel E. Prober,
Philip Kim
Abstract:
We characterize the terahertz detection mechanism in antenna-coupled metallic single-walled carbon nanotubes. At low temperature, 4.2 K, a peak in the low-frequency differential resistance is observed at zero bias current due to non-Ohmic contacts. This electrical contact nonlinearity gives rise to the measured terahertz response. By modeling each nanotube contact as a nonlinear resistor in parall…
▽ More
We characterize the terahertz detection mechanism in antenna-coupled metallic single-walled carbon nanotubes. At low temperature, 4.2 K, a peak in the low-frequency differential resistance is observed at zero bias current due to non-Ohmic contacts. This electrical contact nonlinearity gives rise to the measured terahertz response. By modeling each nanotube contact as a nonlinear resistor in parallel with a capacitor, we determine an upper bound for the value of the contact capacitance that is smaller than previous experimental estimates. The small magnitude of this contact capacitance has favorable implications for the use of carbon nanotubes in high-frequency device applications.
△ Less
Submitted 28 March, 2012;
originally announced March 2012.
-
Proposal for a GHz count rate near-IR single-photon detector based on a nanoscale superconducting transition edge sensor
Authors:
Daniel F. Santavicca,
Faustin W. Carter,
Daniel E. Prober
Abstract:
We describe a superconducting transition edge sensor based on a nanoscale niobium detector element. This device is predicted to be capable of energy-resolved near-IR single-photon detection with a GHz count rate. The increased speed and sensitivity of this device compared to traditional transition edge sensors result from the very small electronic heat capacity of the nanoscale detector element. I…
▽ More
We describe a superconducting transition edge sensor based on a nanoscale niobium detector element. This device is predicted to be capable of energy-resolved near-IR single-photon detection with a GHz count rate. The increased speed and sensitivity of this device compared to traditional transition edge sensors result from the very small electronic heat capacity of the nanoscale detector element. In the present work, we calculate the predicted thermal response time and energy resolution. We also discuss approaches for achieving efficient optical coupling to the sub-wavelength detector element using a resonant near-IR antenna.
△ Less
Submitted 21 February, 2012;
originally announced February 2012.
-
Bolometric and non-bolometric radio frequency detection in a metallic single-walled carbon nanotube
Authors:
Daniel F. Santavicca,
Joel D. Chudow,
Daniel E. Prober,
Meninder S. Purewal,
Philip Kim
Abstract:
We characterize radio frequency detection in a high-quality metallic single-walled carbon nanotube. At a bath temperature of 77 K, only bolometric (thermal) detection is seen. At a bath temperature of 4.2 K and low bias current, the response is due instead to the electrical nonlinearity of the non-ohmic contacts. At higher bias currents, the contacts recover ohmic behavior and the observed respons…
▽ More
We characterize radio frequency detection in a high-quality metallic single-walled carbon nanotube. At a bath temperature of 77 K, only bolometric (thermal) detection is seen. At a bath temperature of 4.2 K and low bias current, the response is due instead to the electrical nonlinearity of the non-ohmic contacts. At higher bias currents, the contacts recover ohmic behavior and the observed response agrees well with the calculated bolometric responsivity. The bolometric response is expected to operate at terahertz frequencies, and we discuss some of the practical issues associated with developing high frequency detectors based on carbon nanotubes.
△ Less
Submitted 3 May, 2011;
originally announced May 2011.
-
Energy loss of the electron system in individual single-walled carbon nanotubes
Authors:
Daniel F. Santavicca,
Joel D. Chudow,
Daniel E. Prober,
Meninder S. Purewal,
Philip Kim
Abstract:
We characterize the energy loss of the non-equilibrium electron system in individual metallic single-walled carbon nanotubes at low temperature. Using Johnson noise thermometry, we demonstrate that, for a nanotube with ohmic contacts, the dc resistance at finite bias current directly reflects the average electron temperature. This enables a straightforward determination of the thermal conductance…
▽ More
We characterize the energy loss of the non-equilibrium electron system in individual metallic single-walled carbon nanotubes at low temperature. Using Johnson noise thermometry, we demonstrate that, for a nanotube with ohmic contacts, the dc resistance at finite bias current directly reflects the average electron temperature. This enables a straightforward determination of the thermal conductance associated with cooling of the nanotube electron system. In analyzing the temperature- and length-dependence of the thermal conductance, we consider contributions from acoustic phonon emission, optical phonon emission, and hot electron outdiffusion.
△ Less
Submitted 4 October, 2010;
originally announced October 2010.
-
Reset dynamics and latching in niobium superconducting nanowire single-photon detectors
Authors:
Anthony J. Annunziata,
Orlando Quaranta,
Daniel F. Santavicca,
Alessandro Casaburi,
Luigi Frunzio,
Mikkel Ejrnaes,
Michael J. Rooks,
Roberto Cristiano,
Sergio Pagano,
Aviad Frydman,
Daniel E. Prober
Abstract:
We study the reset dynamics of niobium (Nb) superconducting nanowire single-photon detectors (SNSPDs) using experimental measurements and numerical simulations. The numerical simulations of the detection dynamics agree well with experimental measurements, using independently determined parameters in the simulations. We find that if the photon-induced hotspot cools too slowly, the device will latch…
▽ More
We study the reset dynamics of niobium (Nb) superconducting nanowire single-photon detectors (SNSPDs) using experimental measurements and numerical simulations. The numerical simulations of the detection dynamics agree well with experimental measurements, using independently determined parameters in the simulations. We find that if the photon-induced hotspot cools too slowly, the device will latch into a dc resistive state. To avoid latching, the time for the hotspot to cool must be short compared to the inductive time constant that governs the resetting of the current in the device after hotspot formation. From simulations of the energy relaxation process, we find that the hotspot cooling time is determined primarily by the temperature-dependent electron-phonon inelastic time. Latching prevents reset and precludes subsequent photon detection. Fast resetting to the superconducting state is therefore essential, and we demonstrate experimentally how this is achieved.
△ Less
Submitted 4 August, 2010;
originally announced August 2010.
-
Tunable superconducting nanoinductors
Authors:
Anthony J Annunziata,
Daniel F Santavicca,
Luigi Frunzio,
Gianluigi Catelani,
Michael J Rooks,
Aviad Frydman,
Daniel E Prober
Abstract:
We characterize inductors fabricated from ultra-thin, approximately 100 nm wide strips of niobium (Nb) and niobium nitride (NbN). These nanowires have a large kinetic inductance in the superconducting state. The kinetic inductance scales linearly with the nanowire length, with a typical value of 1 nH/um for NbN and 44 pH/um for Nb at a temperature of 2.5 K. We measure the temperature and current d…
▽ More
We characterize inductors fabricated from ultra-thin, approximately 100 nm wide strips of niobium (Nb) and niobium nitride (NbN). These nanowires have a large kinetic inductance in the superconducting state. The kinetic inductance scales linearly with the nanowire length, with a typical value of 1 nH/um for NbN and 44 pH/um for Nb at a temperature of 2.5 K. We measure the temperature and current dependence of the kinetic inductance and compare our results to theoretical predictions. We also simulate the self-resonant frequencies of these nanowires in a compact meander geometry. These nanowire inductive elements have applications in a variety of microwave frequency superconducting circuits.
△ Less
Submitted 27 September, 2010; v1 submitted 23 July, 2010;
originally announced July 2010.
-
Energy resolution of terahertz single-photon-sensitive bolometric detectors
Authors:
D. F. Santavicca,
B. Reulet,
B. S. Karasik,
S. V. Pereverzev,
D. Olaya,
M. E. Gershenson,
L. Frunzio,
D. E. Prober
Abstract:
We report measurements of the energy resolution of ultra-sensitive superconducting bolometric detectors. The device is a superconducting titanium nanobridge with niobium contacts. A fast microwave pulse is used to simulate a single higher-frequency photon, where the absorbed energy of the pulse is equal to the photon energy. This technique allows precise calibration of the input coupling and avo…
▽ More
We report measurements of the energy resolution of ultra-sensitive superconducting bolometric detectors. The device is a superconducting titanium nanobridge with niobium contacts. A fast microwave pulse is used to simulate a single higher-frequency photon, where the absorbed energy of the pulse is equal to the photon energy. This technique allows precise calibration of the input coupling and avoids problems with unwanted background photons. Present devices have an intrinsic full-width at half-maximum energy resolution of approximately 23 terahertz, near the predicted value due to intrinsic thermal fluctuation noise.
△ Less
Submitted 1 March, 2010; v1 submitted 5 June, 2009;
originally announced June 2009.
-
Niobium superconducting nanowire single-photon detectors
Authors:
Anthony J. Annunziata,
Daniel F. Santavicca,
Joel D. Chudow,
Luigi Frunzio,
Michael J. Rooks,
Aviad Frydman,
Daniel E. Prober
Abstract:
We investigate the performance of superconducting nanowire photon detectors fabricated from ultra-thin Nb. A direct comparison is made between these detectors and similar nanowire detectors fabricated from NbN. We find that Nb detectors are significantly more susceptible than NbN to thermal instability (latching) at high bias. We show that the devices can be stabilized by reducing the input resi…
▽ More
We investigate the performance of superconducting nanowire photon detectors fabricated from ultra-thin Nb. A direct comparison is made between these detectors and similar nanowire detectors fabricated from NbN. We find that Nb detectors are significantly more susceptible than NbN to thermal instability (latching) at high bias. We show that the devices can be stabilized by reducing the input resistance of the readout. Nb detectors optimized in this way are shown to have approximately 2/3 the reset time of similar large-active-area NbN detectors of the same geometry, with approximately 6% detection efficiency for single photons at 470 nm.
△ Less
Submitted 8 January, 2009;
originally announced January 2009.
-
Impedance-matched low-pass stripline filters
Authors:
D. F. Santavicca,
D. E. Prober
Abstract:
We have constructed several impedance-matched low-pass filters using a stripline geometry with a dissipative dielectric. The filters are compact, simple to construct, and operate in cryogenic environments. The dissipative dielectric consists of magnetically-loaded silicone or epoxy, which are commercially available under the trade name Eccosorb. For a stripline length of 32 mm, the filters have…
▽ More
We have constructed several impedance-matched low-pass filters using a stripline geometry with a dissipative dielectric. The filters are compact, simple to construct, and operate in cryogenic environments. The dissipative dielectric consists of magnetically-loaded silicone or epoxy, which are commercially available under the trade name Eccosorb. For a stripline length of 32 mm, the filters have a passband that extends from dc to a 3 dB bandwidth between 0.3 and 0.8 GHz. The 3 dB bandwidth can be adjusted beyond this range by changing the filter length. An extremely broad stopband at higher frequencies, with attenuation exceeding 100 dB, is achieved along with a return loss greater than 10 dB measured up to 40 GHz. This combination of high attenuation and low reflected power across a broad stopband ensures that spurious or unwanted signals outside the passband do not reach or return to the device under test. This type of filter has applications in microwave frequency measurements of sensitive non-linear devices such as superconducting heterodyne mixers, quantum tunneling devices, and quantum computing elements.
△ Less
Submitted 12 June, 2008; v1 submitted 10 February, 2008;
originally announced February 2008.
-
Hot Electron Bolometer Development for a Submillimeter Heterodyne Array Camera
Authors:
Matthew O. Reese,
Daniel F. Santavicca,
Luigi Frunzio,
Daniel E. Prober
Abstract:
We are developing Nb diffusion-cooled Hot Electron Bolometers (HEBs) for a large-format array submillimeter camera. We have fabricated Nb HEBs using a new angle deposition process. We have characterized these devices using heterodyne mixing at 20 GHz. We also report on optimizations in the fabrication process that improve device performance.
We are developing Nb diffusion-cooled Hot Electron Bolometers (HEBs) for a large-format array submillimeter camera. We have fabricated Nb HEBs using a new angle deposition process. We have characterized these devices using heterodyne mixing at 20 GHz. We also report on optimizations in the fabrication process that improve device performance.
△ Less
Submitted 19 June, 2006;
originally announced June 2006.
