-
Fabrication and Characterization of Graphene-Barium Titanate-Graphene layered capacitors by spin coating at low processing temperatures
Authors:
M. S. Habib,
S. F. U. Farhad,
N. I. Tanvir,
M. S. Alam,
M. N. A. Bitu,
M. S. Islam,
S. Islam,
N. Khatun,
M. S Hossain
Abstract:
Barium titanate, BaTiO3 (BT), materials have been synthesized by two different routes: one ball-mill-derived (BMD) nanopowder and another precursor-derived (PCD) BT synthesis method were used separately to fabricate BT thin films on stainless steel (SS) and quartz substrates by spin coating. Then thin films from both synthesis routes were characterized by Ultraviolet-Visible-Near Infrared (UV-Vis-…
▽ More
Barium titanate, BaTiO3 (BT), materials have been synthesized by two different routes: one ball-mill-derived (BMD) nanopowder and another precursor-derived (PCD) BT synthesis method were used separately to fabricate BT thin films on stainless steel (SS) and quartz substrates by spin coating. Then thin films from both synthesis routes were characterized by Ultraviolet-Visible-Near Infrared (UV-Vis-NIR) Spectroscopy, Field-Emission Scanning Electron Microscopy (FE-SEM), X-ray Diffractometry (XRD), Raman Spectroscopy, and Four-point collinear probe; all carried out at room temperature. Our studies revealed that the PCD synthesis process did not produce the BT phase even under the 900^0C air-annealing condition. In contrast, a homogeneous BT thin film has been formed from the BMD-BT nanopowder. The optical band gap of BMD-BT thin films was found in the 3.10 - 3.28 eV range. Finally, a Graphene-Barium Titanate-Graphene (G-BT-G) structure was fabricated on a SS substrate by spin coating at processing temperatures below 100^0C and characterized by two different pieces of equipment: a Potentiostat/Galvanostat (PG-STAT) and a Precision Impedance Analyzer (PIA). The G-BT-G structure exhibited a capacitance of 8 nF and 7.15 nF, a highest dielectric constant of 800 and 790, and a low dielectric loss of 4.5 and 5, investigated by PG-STAT and PIA equipment, respectively.
△ Less
Submitted 17 June, 2023;
originally announced June 2023.
-
A LED-based Functional Light Source for the Characterization of Thin Film Solar Cells
Authors:
Md. Saidul Islam,
Syed Farid Uddin Farhad,
Md. Saidul Islam,
Nazmul Islam Tanvir,
Suravi Islam
Abstract:
A light source of selective functionalities of wavelengths, illumination periods, and intensities is desirable for investigating performance parameters as well as the quality of different layers and interfaces of solar cells. Conventional light sources used for these types of research are expensive, space-consuming, cumbersome to work with, and have limited functionalities. We have developed a lig…
▽ More
A light source of selective functionalities of wavelengths, illumination periods, and intensities is desirable for investigating performance parameters as well as the quality of different layers and interfaces of solar cells. Conventional light sources used for these types of research are expensive, space-consuming, cumbersome to work with, and have limited functionalities. We have developed a light source with variable wavelength, intensity, and illumination period to address these issues using an illumination period control unit, voltage regulator, neutral density filter, alterable light emitting diodes, etc. As a proof-of-concept, we employed our constructed light source to investigate the intensity, wavelength, illumination period modulated photovoltaic, and impedance properties of inorganic thin film solar cells such as cadmium telluride (CdTe) and copper zinc tin sulfide (CZTS) using lights of wavelength 410, 520, and 635 nm. We hope to use this light source for photophysical and photochemical studies of metal oxide materials used for renewable energy research.
△ Less
Submitted 15 February, 2023; v1 submitted 10 February, 2023;
originally announced February 2023.
-
Effect of Substrate Surface on the Wide Bandgap SnO2 Thin Films Grown by Spin Coating
Authors:
Md. Nur Amin Bitu,
Nazmul Islam Tanvir,
Suravi Islam,
Syed Farid Uddin Farhad
Abstract:
Tin (IV) oxide (SnO2) sols have been synthesized from SnCl2.2H2O precursor solution by applying two different processing conditions. The prepared sols were then deposited on UV-Ozone treated quartz and soda lime glass (SLG) substrates by spin coating. The as-synthesized film was soft-baked at about 100 deg. C. for 10 min. This process was repeated five times to get a compact film, followed by air-…
▽ More
Tin (IV) oxide (SnO2) sols have been synthesized from SnCl2.2H2O precursor solution by applying two different processing conditions. The prepared sols were then deposited on UV-Ozone treated quartz and soda lime glass (SLG) substrates by spin coating. The as-synthesized film was soft-baked at about 100 deg. C. for 10 min. This process was repeated five times to get a compact film, followed by air-annealing at 250 deg. C. for 2 hours. The pristine and annealed films were characterized by UV-Vis-NIR spectroscopy, Grazing Incident X-Ray Diffraction (GIXRD), and Field Emission Scanning Electron Microscope (FESEM). The effect of the substrate surface was investigated by measuring the contact angles with De-Ionized (DI) water. UV-Ozone treatment of substrate provides a cleaner surface to grow a homogeneous film. The electrical resistivity of annealed thin films was carried out by a four-point-collinear probe employing the current reversal technique and found in the range of approx. 2x10^3 to 3x10^3 Ohm-cm. Film thickness was found in the range of approx. 137-285 nm, measured by a stylus profilometer. UV-VIs-NIR Transmission data revealed that all the thin film samples showed maximum (82-89) % transmission in the visible range. The optical bandgap of the thin films was estimated to be approx. 3.75-4.00 eV and approx. 3.78-4.35 eV for the films grown on SLG and quartz substrates, respectively.
△ Less
Submitted 29 January, 2023; v1 submitted 20 September, 2022;
originally announced September 2022.
-
Spherical and Rod-shaped Gold Nanoparticles for Surface Enhanced Raman Spectroscopy
Authors:
Md. Shaha Alam,
Syed Farid Uddin Farhad,
Nazmul Islam Tanvir,
Md. Nur Amin Bitu,
Mohammad Moniruzzaman,
Mahmuda Hakim,
Md Aftab Ali Shaikh
Abstract:
Raman Spectroscopy offers an in-situ, rapid, and non-destructive characterization tool for chemical analysis of diverse samples with no or minimal preparation. However, due to the inherent weak signal of conventional Raman spectroscopy, surface plasmon resonance features of noble metal nanoparticles have been utilized to conduct Surface Enhanced Raman Spectroscopy (SERS) in detecting trace label c…
▽ More
Raman Spectroscopy offers an in-situ, rapid, and non-destructive characterization tool for chemical analysis of diverse samples with no or minimal preparation. However, due to the inherent weak signal of conventional Raman spectroscopy, surface plasmon resonance features of noble metal nanoparticles have been utilized to conduct Surface Enhanced Raman Spectroscopy (SERS) in detecting trace label contaminants in foods and foodstuffs. In this effort, we synthesized gold nanoparticles (AuNPs) by reduction of chloroauric acid (HAuCl4) with sodium citrate dehydrate. We prepared different sizes of AuNPs at a fixed temperature (100 oC) but with varying pHs of 4 and 8. The as-synthesized AuNPs were characterized by UV-Vis spectroscopy, dynamic light scattering (DLS), and Field Emission Scanning Electron Microscopy (FE-SEM). FE-SEM micrographs revealed spherical AuNPs with an average diameter of approx. 55 nm and rod-shaped AuNPs with an average length of approx. 170 nm for sample synthesis at pH 8 and 4, respectively. The effectiveness of the as-prepared AuNPs for SERS is tested by detecting Rhodamine 6G diluted at a trace level. This study suggests that plasmonic nanoparticles coupled with SERS have great potential for broad applications in detecting other trace amounts of hazardous chemicals in foods and foodstuffs.
△ Less
Submitted 1 October, 2022; v1 submitted 19 September, 2022;
originally announced September 2022.
-
A facile top-down synthesis of phase pure CuBi2O4 photocathode materials by low-energy sequential ball milling
Authors:
Syed Farid Uddin Farhad,
Mst. Irin Naher,
Nazmul Islam Tanvir,
Md Saiful Quddus,
Shirin Akter Jahan,
Suravi Islam,
Md. Aftab Ali Shaikh
Abstract:
Kusachiite (copper bismuth oxide) is one of the most promising photocathode materials for high solar-to-hydrogen production efficiency. Here we attempt to synthesize phase pure copper bismuth oxide (CuBi2O4) nanopowders using a facile solid-state reaction technique, subsequently sintered at 750 0C for 4 h in air. These CuBi2O4 (CBO) powders have been further sequentially ball-milled (SBM) up to 25…
▽ More
Kusachiite (copper bismuth oxide) is one of the most promising photocathode materials for high solar-to-hydrogen production efficiency. Here we attempt to synthesize phase pure copper bismuth oxide (CuBi2O4) nanopowders using a facile solid-state reaction technique, subsequently sintered at 750 0C for 4 h in air. These CuBi2O4 (CBO) powders have been further sequentially ball-milled (SBM) up to 25 h to elucidate the milling duration effect on the optical bandgap of the ball-milled CuBi2O4 (SBM-CBO). The X-ray diffractometry (XRD), Raman, X-ray Photoelectron spectroscopy (XPS), and UV-VIS-NIR Diffuse reflection studies suggest that phase pure tetragonal CBO could be grown from raw CuO and Bi2O3 powders. The variations in morphology and chemical composition of CBO with increasing milling hours were examined using field emission scanning electron microscopy (FE-SEM) and Energy Dispersive X-ray (EDX) microanalysis, respectively. The optical bandgap of SBM-CBO powders was measured in the range of approx. 1.70 - 1.85 eV. Photoelectrochemical studies of SBM-CBO slurry atop the screen-printed electrode with aqueous Na2SO4 electrolyte suggest its suitability as photocathode materials for sunlight-driven hydrogen production.
△ Less
Submitted 10 February, 2023; v1 submitted 18 September, 2022;
originally announced September 2022.
-
Facile synthesis of Cu2O nanorods in the presence of NaCl by SILAR method and its characterizations
Authors:
Md. Alauddin Hossain,
Syed Farid Uddin Farhad,
Nazmul Islam Tanvir,
Jang Hyo Chang,
Mohammad Atiqur Rahman,
Tooru Tanaka,
Qixin Guo,
Jamal Uddin,
Md Abdul Majed Patwary
Abstract:
Cu2O nanorods have been deposited on soda-lime glass (SLG) substrates by the modified SILAR technique by varying the concentration of NaCl electrolyte into the precursor complex solution. The structural, electrical, and optical properties of synthesized Cu2O nanorod films have been studied by a variety of characterization tools. Structural analyses by XRD confirmed the polycrystalline Cu2O phase w…
▽ More
Cu2O nanorods have been deposited on soda-lime glass (SLG) substrates by the modified SILAR technique by varying the concentration of NaCl electrolyte into the precursor complex solution. The structural, electrical, and optical properties of synthesized Cu2O nanorod films have been studied by a variety of characterization tools. Structural analyses by XRD confirmed the polycrystalline Cu2O phase with (111) preferential growth. Raman scattering spectroscopic measurements conducted at room temperature also showed characteristic peaks of the pure Cu2O phase. The surface resistivity of the Cu2O nanorod films decreased from 15,142 to 685 Ohm.cm with the addition of NaCl from 0 to 4 mmol, and then exhibited an opposite trend with further addition of NaCl. The optical bandgap of the synthesized Cu2O nanorod films was observed as 1.88 - 2.36 eV, while the temperature-dependent activation energies of the Cu2O films were measured as about 0.14 - 0.21 eV. SEM morphologies demonstrated Cu2O nanorod as well as closely packed spherical grains with the alteration of NaCl concentration. The Cu2O phase of nanorods was found stable up to 230 0C corroborating the optical bandgap results of the same. The film fabricated in presence of 4 mmol of NaCl showed the lowest resistivity and activation energy as well comparatively uniform nanorod morphology. Our studies demonstrate that the nominal presence of NaCl electrolytes in the pre-cursor solutions has a significant impact on the physical properties of Cu2O nanorod films which could be beneficial in optoelectronic research.
△ Less
Submitted 22 March, 2022; v1 submitted 11 March, 2022;
originally announced March 2022.
