Ryde Bridge

Ryde Bridge
Ryde Bridge, viewed from Meadowbank in 2006
Coordinates	33°49′25″S 151°05′42″E
Carries	Concord Road Motor vehicles Grade-separated pedestrian footpath
Crosses	Parramatta River
Locale	Ryde, Sydney, New South Wales, Australia
Begins	Ryde (north)
Ends	Rhodes (south)
Other name(s)	Uhrs Point Bridge
Named for	The Sydney suburb of Ryde
Owner	Transport for NSW
Heritage status	Transport for NSW heritage and conservation register
Preceded by	Meadowbank Railway Bridge
Followed by	Mortlake Ferry
Characteristics
Design	Pratt truss with inoperable lift span (west) Fixed-span bridge (east)
Material	Steel (west) Reinforced concrete (east)
Pier construction	Reinforced concrete octagonal columns (west) Concrete (east)
No. of lanes	6: 3 lanes each bridge
History
Designer	Department of Main Roads
Construction start	1931 (1931) 1987 (1987)
Inaugurated	7 December 1935 (1935-12-07) by the NSW Premier Bertram Stevens (west) 25 November 1988 (1988-11-25) by the NSW Premier Nick Greiner and Minister for Transport Ralph Willis (east)
Replaces	Man-powered punt (1896–1935) (west) Single carriageway Ryde Bridge (1935–1988) (east)
Statistics
Toll	1935-1948
Location
References

The Ryde Bridge, also called the Uhrs Point Bridge, are two road bridges that carry Concord Road, part of the A3, across Parramatta River from Ryde in the northern suburbs of Sydney to Rhodes in Sydney's inner west, in New South Wales, Australia.

The two bridges comprise a heritage-listed steel Pratt truss bridge with inoperable lift span that carries three lanes of northbound vehicular traffic plus a grade-separated pedestrian footpath, completed in 1935; and a reinforced concrete fixed-span bridge that carries three lanes of southbound vehicular traffic, completed in 1988.

History

A proposal for the construction of a bridge in lieu of a ferry over the Parramatta River, between Meadowbank and Rhodes, was first submitted to the Minister for Public Works in 1913. Owing to funds being unavailable for the purpose, no action was taken until 1920. In July 1924, the Minister for Public Works announced in Parliament that he was prepared to introduce a bill to give the involved councils the power to build the bridge. A site investigation followed, and its results was transferred to the Main Roads Board in July 1928.

The original Ryde Bridge was opened on 7 December 1935 by the Premier Bertram Stevens, accompanied by the Mayor of Ryde. The original bridge is a lift bridge, which was required to allow shipping to pass to the State Timber Yard then located on the southern bank of the Parramatta River, just west of the bridge. However the lifting mechanism was removed in the late 20th century and it has not been opened since. The bridge was paid for by the Ryde Council with the assistance of a grant from the New South Wales Government. The bridge carried a toll for 13 years until the bridge was paid for. In 1948, ownership of the bridge was transferred to the Department of Main Roads.

A new bridge was built on the eastern or downstream side using steel trough girders, closed on top by a composite concrete running deck, and completed in 1987. The second bridge carries southbound traffic, with the original bridge carrying northbound traffic only. It was officially opened on 25 November 1988 by the Premier Nick Greiner and Federal Minister For Transport Ralph Willis.

Before the original bridge was constructed, the Parramatta River was crossed in this area by a vehicular punt, just downstream of the Meadowbank Railway Bridge. The southern ramp still exists near the southern end of the railway bridge, however the northern ramp has been covered over by Meadowbank ferry wharf.

Heritage significance

Ryde Bridge has rarity value at a State level and historical significance locally. Ryde Bridge spans the Parramatta River between Church Street in Ryde (Uhrs Point) and Concord Road in Rhodes, replacing an earlier ferry service between these two points established in the late nineteenth century. It is rare at a state level because it is the only lift span bridge on Sydney Harbour and its tributaries (although the mechanism to operate the vertical lift span has been removed). Ryde Bridge, constructed in 1935, is also a relatively rare example of a steel truss bridge with a lift span in NSW. By the early 1950s, the bascule span was the preferred option for bridges with opening spans, meaning that vertical lift span bridges such as Ryde Bridge were no longer being designed and built. Ryde Bridge has local historical significance because it is located at an important crossing over the Parramatta River, between Ryde and Rhodes, which was one of the narrowest points on the river. Ryde Council initiated the construction of the bridge in order to open up the municipality for suburban development. Thereafter, Ryde Bridge has provided an important transportation route for outer suburbs in the municipalities of Ryde and Hornsby to access Sydney by car.

— Statement of significance, Heritage and conservation register, Roads & Maritime Services, 15 August 2005.

Other

The Hexham Bridge, located 125 kilometres (78 mi) northeast of Sydney and which spans the Hunter River is very similar to 1935 Pratt truss Ryde Bridge.

External links

• Kass, Terry (February 2006). "RTA Thematic History: A component of the RTA Heritage and Conservation Register" (PDF). Roads & Maritime Services (PDF) (2nd ed.). Government of New South Wales. Retrieved 12 January 2015.