CCNA(200-125)

266Q_CCNA_200_125_4_4_2017_v1 Number: 200-125 Passing Score: 820 Time Limit: 120 min File Version: 1.0 update 5 - April - 2017 266Q_CCNA_200_125_4_4_2017_v2 Sections 1. (none) CCNA 200-125 QUESTION 1 Which technology supports the stateless assignment of IPv6 addresses? A. B. C. D. DNS DHCPv6 DHCP autoconfiguration Correct Answer: BD Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 2 What are two requirements for an HSRP group? (Choose two.) A. B. C. D. E. exactly one active router one or more standby routers one or more backup virtual routers exactly one standby active router exactly one backup virtual router Correct Answer: AB Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 3 After you configure the Loopback0 interface, which command can you enter to verify the status of the interface and determine whether fast switching is enabled? A. B. C. D. Router#show ip interface loopback 0 Router#show run Router#show interface loopback 0 Router#show ip interface brief Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 4 Which command sequence can you enter to create VLAN 20 and assign it to an interface on a switch? A. Switch(config)#vlan 20 Switch(config)#Interface gig x/y Switch(config-if)#switchport access vlan 20 B. Switch(config)#Interface gig x/y Switch(config-if)#vlan 20 Switch(config-vlan)#switchport access vlan 20 C. Switch(config)#vlan 20 Switch(config)#Interface vlan 20 Switch(config-if)#switchport trunk native vlan 20 D. Switch(config)#vlan 20 Switch(config)#Interface vlan 20 Switch(config-if)#switchport access vlan 20 E. Switch(config)#vlan 20 Switch(config)#Interface vlan 20 Switch(config-if)#switchport trunk allowed vlan 20 Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 5 Which three commands can you use to set a router boot image? (Choose three.) A. B. C. D. E. F. Router(config)# boot system flash c4500-p-mz.121-20.bin Router(config)# boot system tftp c7300-js-mz.122-33.SB8a.bin Router(config)#boot system rom c7301-advipservicesk9-mz.124-24.T4.bin Router> boot flash:c180x-adventerprisek9-mz-124-6T.bin Router(config)#boot flash:c180x-adventerprisek9-mz-124-6T.bin Router(config)#boot bootldr bootflash:c4500-jk9s-mz.122-23f.bin Correct Answer: ABC Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 6 Which two statements about IPv6 and routing protocols are true? (Choose two.) A. B. C. D. E. Link-local addresses are used to form routing adjacencies. OSPFv3 was developed to support IPv6 routing. EIGRP, OSPF, and BGP are the only routing protocols that support IPv6. Loopback addresses are used to form routing adjacencies. EIGRPv3 was developed to support IPv6 routing. Correct Answer: AB Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 7 If primary and secondary root switches with priority 16384 both experience catastrophic losses, which tertiary switch can take over? A. B. C. D. a switch with priority 20480 a switch with priority 8192 a switch with priority 4096 a switch with priority 12288 Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 8 Which two statements about late collisions are true? (Choose two.) A. B. C. D. E. They may indicate a duplex mismatch. By definition, they occur after the 512th bit of the frame has been transmitted. They indicate received frames that did not pass the FCS match. They are frames that exceed 1518 bytes. They occur when CRC errors and interference occur on the cable. Correct Answer: AB Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 9 Which command can you enter to set the default route for all traffic to an interface? A. B. C. D. router(config)#ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/1 router(config)#ip route 0.0.0.0 255.255.255.255 GigabitEthernet0/1 router(config-router)#default-information originate router(config-router)#default-information originate always Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 10 Which two spanning-tree port states does RSTP combine to allow faster convergence? (Choose two.) A. B. C. D. E. blocking listening learning forwarding discarding Correct Answer: AB Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 11 If a router has four interfaces and each interface is connected to four switches, how many broadcast domains are present on the router? A. B. C. D. 1 2 4 8 Correct Answer: C Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 12 The left describes the types of cables, while the right describes the purposes of the cables. Drag the items on the left to the proper locations. (Not all items can be used.) (THE COMMUNITY SHARED THAT THERE IS ANOTHER OPTION SO STUDY ALL OF WHAT THIS CABLES ARE FOR) A. Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 13 Match the items on the left with appropriate OSI layer on the right. (Not all options are used.) A. Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 14 Which command enables IPv6 forwarding on a Cisco router? A. B. C. D. ipv6 local ipv6 host ipv6 unicast-routing ipv6 neighbor Correct Answer: C Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 15 Refer to the exhibit. What is the most appropriate summarization for these routes? A. B. C. D. 10.0.0.0 /21 10.0.0.0 /22 10.0.0.0 /23 10.0.0.0 /24 Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: The 10.0.0.0/22 subnet mask will include the 10.0.0.0, 10.0.1.0, 10.0.2.0, and 10.0.3.0 networks, and only those four networks. QUESTION 16 Which set of commands is recommended to prevent the use of a hub in the access layer? A. switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security maximum 1 B. switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security mac-address 1 C. switch(config-if)#switchport mode access switch(config-if)#switchport port-security maximum 1 D. switch(config-if)#switchport mode access switch(config-if)#switchport port-security mac-address 1 Correct Answer: C Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 17 A router has learned three possible routes that could be used to reach a destination network. One route is from EIGRP and has a composite metric of 20514560. Another route is from OSPF with a metric of 782. The last is from RIPv2 and has a metric of 4. Which route or routes will the router install in the routing table? A. B. C. D. E. the OSPF route the EIGRP route the RIPv2 route all three routes the OSPF and RIPv2 routes Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 18 Two routers named Atlanta and Brevard are connected via their serial interfaces as illustrated, but they are unable to communicate. The Atlanta router is known to have the correct configuration. Given the partial configurations, identify the fault on the Brevard router that is causing the lack of connectivity A. B. C. D. E. F. incompatible IP address insufficient bandwidth incorrect subnet mask incompatible encapsulation link reliability too low IPCP closed Correct Answer: D Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 19 A network administrator needs to configure a serial link between the main office and a remote location. The router at the remote office is a non-Cisco router. How should the network administrator configure the serial interface of the main office router to make the connection? A. Main(config)# interface serial 0/0 Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# no shut B. Main(config)# interface serial 0/0 Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# encapsulation ppp Main(config-if)# no shut C. Main(config)# interface serial 0/0 Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# encapsulation frame-relay Main(config-if)# authentication chap Main(config-if)# no shut D. Main(config)# interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation ietf Main(config-if)# no shut Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 20 Which Layer 2 protocol encapsulation type supports synchronous and asynchronous circuits and has built-in security mechanisms? A. B. C. D. HDLC PPP X.25 Frame Relay Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 21 Refer to the exhibit. The two connected ports on the switch are not turning orange or green. What would be the most effective steps to troubleshoot this physical layer problem? (Choose three.) A. B. C. D. E. F. Ensure that the Ethernet encapsulations match on the interconnected router and switch ports. Ensure that cables A and B are straight-through cables. Ensure cable A is plugged into a trunk port. Ensure the switch has power. Reboot all of the devices. Reseat all cables. Correct Answer: BDF Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 22 A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link. The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem? A. B. C. D. E. F. The OSPF area is not configured properly. The priority on R1 should be set higher. The cost on R1 should be set higher. The hello and dead timers are not configured properly. A backup designated router needs to be added to the network. The OSPF process ID numbers must match. Correct Answer: D Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 23 What will happen if a private IP address is assigned to a public interface connected to an ISP? A. B. C. D. Addresses in a private range will be not be routed on the Internet backbone. Only the ISP router will have the capability to access the public network. The NAT process will be used to translate this address to a valid IP address. A conflict of IP addresses happens, because other public routers can use the same range. Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 24 Refer to the exhibit. The Bigtime router is unable to authenticate to the Littletime router. What is the cause of the problem? A. B. C. D. E. The usernames are incorrectly configured on the two routers. The passwords do not match on the two routers. CHAP authentication cannot be used on a serial interface. The routers cannot be connected from interface S0/0 to interface S0/0. With CHAP authentication, one router must authenticate to another router. The routers cannot be configured to authenticate to each other. Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 25 What will be the result if the following configuration commands are implemented on a Cisco switch? Switch(config-if)# switchport port-security Switch(config-if)# switchport port-security mac-address sticky A. B. C. D. A dynamically learned MAC address is saved in the startup-configuration file. A dynamically learned MAC address is saved in the running-configuration file. A dynamically learned MAC address is saved in the VLAN database. Statically configured MAC addresses are saved in the startup-configuration file if frames from that address are received. E. Statically configured MAC addresses are saved in the running-configuration file if frames from that address are received. Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 26 Refer to the exhibit. The following commands are executed on interface fa0/1 of 2950Switch. 2950Switch(config-if)# switchport port-security 2950Switch(config-if)# switchport port-security mac-address sticky 2950Switch(config-if)# switchport port-security maximum 1 The Ethernet frame that is shown arrives on interface fa0/1. What two functions will occur when this frame is received by 2950Switch? (Choose two.) A. B. C. D. E. The MAC address table will now have an additional entry of fa0/1 FFFF.FFFF.FFFF. Only host A will be allowed to transmit frames on fa0/1. This frame will be discarded when it is received by 2950Switch. All frames arriving on 2950Switch with a destination of 0000.00aa.aaaa will be forwarded out fa0/1. Hosts B and C may forward frames out fa0/1 but frames arriving from other switches will not be forwarded out fa0/1. F. Only frames from source 0000.00bb.bbbb, the first learned MAC address of 2950Switch, will be forwarded out fa0/1. Correct Answer: BD Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 27 Which command would you configure globally on a Cisco router that would allow you to view directly connected Cisco devices? A. B. C. D. enable cdp cdp enable cdp run run cdp Correct Answer: C Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 28 A Cisco router is booting and has just completed the POST process. It is now ready to find and load an IOS image. What function does the router perform next? A. B. C. D. It checks the configuration register. It attempts to boot from a TFTP server. It loads the first image file in flash memory. It inspects the configuration file in NVRAM for boot instructions. Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 29 What are three advantages of VLANs? (Choose three.) A. B. C. D. E. F. VLANs establish broadcast domains in switched networks. VLANs utilize packet filtering to enhance network security. VLANs provide a method of conserving IP addresses in large networks. VLANs provide a low-latency internetworking alternative to routed networks. VLANs allow access to network services based on department, not physical location. VLANs can greatly simplify adding, moving, or changing hosts on the network. Correct Answer: AEF Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 30 Refer to the exhibit. The output that is shown is generated at a switch. Which three statements are true? (Choose three.) A. B. C. D. E. F. All ports will be in a state of discarding, learning, or forwarding. Thirty VLANs have been configured on this switch. The bridge priority is lower than the default value for spanning tree. All interfaces that are shown are on shared media. All designated ports are in a forwarding state. This switch must be the root bridge for all VLANs on this switch. Correct Answer: ACE Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 31 Which two commands can be used to verify a trunk link configuration status on a given Cisco switch interface? (Choose two.) A. B. C. D. E. show interface trunk show interface interface show ip interface brief show interface vlan show interface switchport Correct Answer: AE Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 32 Which two states are the port states when RSTP has converged? (Choose two.) A. B. C. D. E. discarding listening learning forwarding disabled Correct Answer: AD Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 33 Refer to the exhibit. A technician has installed Switch B and needs to configure it for remote access from the management workstation connected to Switch A . Which set of commands is required to accomplish this task? A. SwitchB(config)# interface FastEthernet 0/1 SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# no shutdown B. SwitchB(config)# interface vlan 1 SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# ip default-gateway 192.168.8.254 255.255.255.0 SwitchB(config-if)# no shutdown C. SwitchB(config)# ip default-gateway 192.168.8.254 SwitchB(config)# interface vlan 1 SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# no shutdown D. SwitchB(config)# ip default-network 192.168.8.254 SwitchB(config)# interface vlan 1 SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# no shutdown E. SwitchB(config)# ip route 192.168.8.254 255.255.255.0 SwitchB(config)# interface FastEthernet 0/1 SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# no shutdown Correct Answer: C Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 34 Which of the following are benefits of VLANs? (Choose three.) A. B. C. D. E. F. They increase the size of collision domains. They allow logical grouping of users by function. They can enhance network security. They increase the size of broadcast domains while decreasing the number of collision domains. They increase the number of broadcast domains while decreasing the size of the broadcast domains. They simplify switch administration. Correct Answer: BCE Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 35 What are three benefits of implementing VLANs? (Choose three.) A. A higher level of network security can be reached by separating sensitive data traffic from other network traffic. B. A more efficient use of bandwidth can be achieved allowing many physical groups to use the same network infrastructure. C. A more efficient use of bandwidth can be achieved allowing many logical networks to use the same network infrastructure. D. Broadcast storms can be mitigated by increasing the number of broadcast domains, thus reducing their size. E. Broadcast storms can be mitigated by decreasing the number of broadcast domains, thus increasing their size. F. VLANs make it easier for IT staff to configure new logical groups, because the VLANs all belong to the same broadcast domain. G. Port-based VLANs increase switch-port use efficiency, thanks to 802.1Q trunks. Correct Answer: ACD Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 36 Which three statements accurately describe Layer 2 Ethernet switches? (Choose three.) A. Spanning Tree Protocol allows switches to automatically share VLAN information. B. Establishing VLANs increases the number of broadcast domains. C. Switches that are configured with VLANs make forwarding decisions based on both Layer 2 and Layer 3 address information. D. Microsegmentation decreases the number of collisions on the network. E. In a properly functioning network with redundant switched paths, each switched segment will contain one root bridge with all its ports in the forwarding state. All other switches in that broadcast domain will have only one root port. F. If a switch receives a frame for an unknown destination, it uses ARP to resolve the address. Correct Answer: BDE Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 37 Which of the following correctly describe steps in the OSI data encapsulation process? (Choose two.) A. The transport layer divides a data stream into segments and may add reliability and flow control information. B. The data link layer adds physical source and destination addresses and an FCS to the segment. C. Packets are created when the network layer encapsulates a frame with source and destination host addresses and protocol-related control information. D. Packets are created when the network layer adds Layer 3 addresses and control information to a segment. E. The presentation layer translates bits into voltages for transmission across the physical link. Correct Answer: AD Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 38 Which of the following describes the roles of devices in a WAN? (Choose three.) A. B. C. D. E. F. A CSU/DSU terminates a digital local loop. A modem terminates a digital local loop. A CSU/DSU terminates an analog local loop. A modem terminates an analog local loop. A router is commonly considered a DTE device. A router is commonly considered a DCE device. Correct Answer: ADE Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 39 Which interface counter can you use to diagnose a duplex mismatch problem? A. B. C. D. E. F. no carrier late collisions giants CRC errors deferred runts Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 40 Which feature can you implement to reserve bandwidth for VoIP calls across the call path? A. B. C. D. PQ CBWFQ round robin RSVP Correct Answer: D Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 41 When an interface is configured with PortFast BPDU guard, how does the interface respond when it receives a BPDU? A. B. C. D. It continues operating normally. It goes into a down/down state. It becomes the root bridge for the configured VLAN. It goes into an errdisable state. Correct Answer: D Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 42 What are three characteristics of the TCP protocol? (Choose three.) A. B. C. D. E. F. It uses a single SYN-ACK message to establish a connection. The connection is established before data is transmitted. It ensures that all data is transmitted and received by the remote device. It supports significantly higher transmission speeds than UDP. It requires applications to determine when data packets must be retransmitted. It uses separate SYN and ACK messages to establish a connection. Correct Answer: BCF Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 43 Which command can you enter to determine whether serial interface 0/2/0 has been configured using HDLC encapsulation? A. B. C. D. router#show platform router#show interfaces Serial 0/2/0 router#show ip interface s0/2/0 router#show ip interface brief Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 44 Which two statements about IPv4 multicast traffic are true? (Choose two.) A. B. C. D. E. It burdens the source host without affecting remote hosts. It uses a minimum amount of network bandwidth. It is bandwidth-intensive. It simultaneously delivers multiple streams of data. It is the most efficient way to deliver data to multiple receivers. Correct Answer: DE Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 45 What are two benefits of private IPv4 IP addresses? (Choose two.) A. B. C. D. E. They are routed the same as public IP addresses. They are less costly than public IP addresses. They can be assigned to devices without Internet connections. They eliminate the necessity for NAT policies. They eliminate duplicate IP conflicts. Correct Answer: BC Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 46 What is the authoritative source for an address lookup? A. B. C. D. a recursive DNS search the operating system cache the ISP local cache the browser cache Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 47 Which command can you enter to verify that a BGP connection to a remote device is established? A. B. C. D. show ip bgp summary show ip community-list show ip bgp paths show ip route Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 48 During which phase of PPPoE is PPP authentication performed ? A. the PPP Session phase B. Phase 2 C. the Active Discovery phase D. the Authentication phase E. Phase 1 Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 49 Which three circumstances can cause a GRE tunnel to be in an up/down state? (Choose three.) A. B. C. D. E. F. The tunnel interface IP address is misconfigured. The tunnel interface is down. A valid route to the destination address is missing from the routing table. The tunnel address is routed through the tunnel itself. The ISP is blocking the traffic. An ACL is blocking the outbound traffic. Correct Answer: BCD Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 50 Which two statements about using leased lines for your WAN infrastructure are true? (Choose two.) A. B. C. D. E. F. Leased lines provide inexpensive WAN access. Leased lines with sufficient bandwidth can avoid latency between endpoints. Leased lines require little installation and maintenance expertise. Leased lines provide highly flexible bandwidth scaling. Multiple leased lines can share a router interface. Leased lines support up to T1 link speeds. Correct Answer: CD Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 51 Which two statements about wireless LAN controllers are true? (Choose two.) A. They can simplify the management and deployment of wireless LANs. B. C. D. E. They rely on external firewalls for WLAN security. They are best suited to smaller wireless networks. They must be configured through a GUI over HTTP or HTTPS. They can manage mobility policies at a systemwide level. Correct Answer: AE Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 52 Which two statements about northbound and southbound APIs are true? (Choose two.) A. B. C. D. E. F. Only southbound APIs allow program control of the network. Only northbound APIs allow program control of the network. Only southbound API interfaces use a Service Abstraction Layer. Only northbound API interfaces use a Service Abstraction Layer. Both northbound and southbound API interfaces use a Service Abstraction Layer. Both northbound and southbound APIs allow program control of the network. Correct Answer: BC Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 53 Which command can you enter to set the default route for all traffic to an interface? A. B. C. D. router(config)#ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/1 router(config-router)#default-information originate always router(config)#ip route 0.0.0.0 255.255.255.255 GigabitEthernet0/1 route(config-router)#default-information originate Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 54 Which statement about RADIUS security is true? A. It supports EAP authentication for connecting to wireless networks. B. It provides encrypted multiprotocol support. C. Device-administration packets are encrypted in their entirety. D. It ensures that user activity is fully anonymous. Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 55 If you are configuring syslog messages specifying `logging trap warning', which log messages will the router send? A. B. C. D. E. 0-4 0-5 0-2 0-6 0-1 Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: 0 emergencies System is unusable 1 alerts Immediate action is needed 2 critical Critical conditions exist 3 errors Error conditions exist 4 warnings Warning conditions exist 5 notification Normal, but significant, conditions exist 6 informational Informational messages 7 debugging Debugging messages QUESTION 56 What is the correct command for floating static ipv6 route? A. B. C. D. ipv6 route 2001:DB8::/32 serial 2/0 201 ipv6 route 2001:DB8::/32 serial 2/0 1 N/A N/A Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 57 What is true about Ethernet? (Choose Two.) A. B. C. D. E. 802.2 Protocol 802.3 Protocol 10BaseT half duplex CSMA/CD Stops transmitting when congestion occurs CSMA/CA Stops transmitting when congestion occurs Correct Answer: BD Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: http://www.ieee802.org/3/ CSMA/CD - It uses a carrier sensing scheme in which a transmitting station detects collisions by sensing transmissions from other stations while transmitting a frame. When this collision condition is detected, the station stops transmitting that frame. QUESTION 58 What IP SLA ICMP Echo measures? A. B. C. D. E. Packet loss Congestion Hop-by-hop "something" -ANOTHER OPTION-ANOTHER OPTION- Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: There is no RRT (Round-trip time) in the choices @Mik said. QUESTION 59 What are types of IPv6 static routes? (Choose Three ) A. B. C. D. E. F. Recursive routes Directly connected routes Fully specified routes Advertised routes Virtual links Redistributed routes Correct Answer: ABC Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: http://ipcisco.com/ipv6-static-routes-for-cisco-routers/ http://www.orbit-computer-solutions.com/ipv6-static-and-default-route-how-to-configure-ipv6-static-anddefault- route/ QUESTION 60 How to configure RIPv2? (Choose Two.) A. B. C. D. E. Enable RIP Connect RIP to WAN interface Enable auto-summary Enable authentication -ANOTHER OPTION- Correct Answer: AC Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: C because we can enable or disable auto-summary in rips. QUESTION 61 What is the status of port-channel if LACP is misconfigured ? A. B. C. D. Forwarding Enabled Disabled Errdisabled Correct Answer: C Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 62 What is true about DTP? (Choose Three.) A. B. C. D. E. Layer 2 protocol Layer 3 protocol Proprietary protocol enabled by default disabled by default Correct Answer: ACD Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: https://en.wikipedia.org/wiki/Dynamic_Trunking_Protocol QUESTION 63 How to create a trunk port and allow VLAN 20? (Choose Three.) A. B. C. D. E. switchport trunk encapsulation dot1q switchport mode trunk switchport trunk allowed vlan 20 switchport trunk native vlan 20 -ANOTHER OPTION- Correct Answer: ABC Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 64 What 8-bit field exists in IP packet for QoS ? A. B. C. D. E. Tos Field DSCP IP Precedence Cos -ANOTHER OPTION- Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: http://flylib.com/books/2/686/1/html/2/images/1587051990/graphics/13fig01.gif QUESTION 65 What feature uses a random time to re-sent a frame? A. B. C. D. CSMA/CA -ANOTHER OPTION-ANOTHER OPTIONCSMA/CD Correct Answer: D Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 66 Which mode is compatible with Trunk, Access, and desirable ports? A. B. C. D. Trunk Ports Access Ports Dynamic Auto Dynamic Desirable Correct Answer: C Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: The 'dynamic auto' will configure the port to accept incoming negotiation and will accept becoming either a trunk or an access port. Dynamic Auto allows the port to negotiate DTP (Dynamic Trunking Protocol) if the other side is set to trunk or desirable. Otherwise it will become an access port. QUESTION 67 If you configure syslog messages without specifying the logging trap level, which log messages will the router send ? A. B. C. D. E. 0-4 0-5 0-2 0-6 0-1 Correct Answer: D Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: Router(config)# logging trap level - Specifies the kind of messages, by severity level, to be sent to the syslog server. The default is informational (6) and lower ( 0 6). The possible values for level are as follows: Emergency: 0 Alert: 1 Critical: 2 Error: 3 Warning: 4 Notice: 5 Informational: 6 Debug: 7 QUESTION 68 Which command can you execute to set the user inactivity timer to 10 seconds? A. SW1(config-line)#exec-timeout 0 10 B. SW1(config-line)#exec-timeout 10 C. SW1(config-line)#absolute-timeout 0 10 D. SW1(config-line)#absolute-timeout 10 Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 69 Which standards-based First Hop Redundancy Protocol is a Cisco supported alternative to Hot Standby Router Protocol? A. B. C. D. VRRP GLBP TFTP DHCP Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 70 Two hosts are attached to a switch with the default configuration. Which statement about the configuration is true? A. B. C. D. IP routing must be enabled to allow the two hosts to communicate. The two hosts are in the same broadcast domain. The switch must be configured with a VLAN to allow the two hosts to communicate. Port security prevents the hosts from connecting to the switch. Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 71 If there are 3 hosts connected in one port of a switch and two other hosts connected in another port, how may collision domains are present on the router? A. B. C. D. 5 2 3 4 Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 72 What are three parts of an IPv6 global unicast address? (Choose three.) A. B. C. D. an interface ID that is used to identify the local host on the network. an interface ID that is used to identify the local network for a particular host. a subnet ID that is used to identify networks inside of the local enterprise site a global routing prefix that is used to identify the network portion of the address that has been provided by an ISP E. a global routing prefix that is used to identify the portion of the network address provided by a local administrator Correct Answer: ACD Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 73 You have been asked to come up with a subnet mask that will allow all three web servers to be on the same network while providing the maximum number of subnets. Which network address and subnet mask meet this requirement? A. B. C. D. E. 192.168.252.0 255.255.255.252 192.168.252.8 255.255.255.248 192.168.252.8 255.255.255.252 192.168.252.16 255.255.255.240 192.168.252.16 255.255.255.252 Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 74 What parameter can be different on ports within an EtherChannel? A. B. C. D. speed DTP negotiation settings trunk encapsulation duplex Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 75 Which two statements about IPv6 router advertisement messages are true? (Choose two.) A. B. C. D. E. They use ICMPv6 type 134. The advertised prefix length must be 64 bits. The advertised prefix length must be 48 bits. They are sourced from the configured IPv6 interface address. Their destination is always the link-local address of the neighboring node. Correct Answer: AB Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 76 Which spanning-tree protocol rides on top of another spanning-tree protocol? A. B. C. D. MSTP RSTP PVST+ Mono Spanning Tree Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 77 A network administrator needs to configure port security on a switch. Which two statements are true? (Choose two.) A. The network administrator can apply port security to dynamic access ports. B. The network administrator can apply port security to EtherChannels. C. The sticky learning feature allows the addition of dynamically learned addresses to the running configuration. D. When dynamic MAC address learning is enabled on an interface, the switch can learn new addresses, up to the maximum defined. E. The network administrator can configure static secure or sticky secure MAC addresses in the voice VLAN Correct Answer: CD Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 78 Which switching method duplicates the first six bytes of a frame before making a switching decision? A. B. C. D. fragment-free switching store-and-forward switching cut-through switching ASIC switching Correct Answer: C Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 79 Which logging command can enable administrators to correlate syslog messages with millisecond precision? A. B. C. D. E. no logging console logging buffered 4 no logging monitor service timestamps log datetime mscec logging host 10.2.0.21 Correct Answer: D Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 80 Which three statements about link-state routing are true? (Choose three.) A. OSPF is a link-state protocol. B. Updates are sent to a broadcast address. C. It uses split horizon. D. Routes are updated when a change in topology occurs. E. RIP is a link-state protocol. F. Updates are sent to a multicast address by default. Correct Answer: ADF Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 81 Which command can you enter to determine whether a switch is operating in trunking mode? A. B. C. D. show ip interface brief show vlan show interfaces show interface switchport Correct Answer: D Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 82 Which command can you enter to view the ports that are assigned to VLAN 20 ? A. B. C. D. Switch#show ip interface vlan 20 Switch#show vlan id 20 Switch#show ip interface brief Switch#show interface vlan 20 Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 83 In which two formats can the IPv6 address fd15:0db8:0000:0000:0700:0003:400F:572B be written? (Choose two.) A. B. C. D. fd15:0db8:0000:0000:700:3:400F:527B fd15::db8::700:3:400F:527B fd15:db8:0::700:3:4F:527B fd15:0db8::7:3:4F:527B E. fd15:db8::700:3:400F:572B Correct Answer: AE Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 84 Which function of the IP SLAs ICMP jitter operation can you use to determine whether a VoIP issue is caused by excessive end-to-end time? A. B. C. D. packet loss jitter successive packet loss round-trip time latency Correct Answer: D Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 85 Refer to the exhibit. Which of these statements correctly describes the state of the switch once the boot process has been completed? A. B. C. D. A. The switch will need a different IOS code in order to support VLANs and ST. Remote access management of this switch will not be possible without configuration change. As FastEthernet0/12 will be the last to come up, it will be blocked by STP. More VLANs will need to be created for this switch. Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 86 Refer to the exhibit. The network administrator normally establishes a Telnet session with the switch from host A. However, host A is unavailable. The administrator's attempt to telnet to the switch from host fails, but pings to the other two hosts are successful. What is the issue? A. B. C. D. E. The switch interfaces need the appropriate IP addresses assigned. Host and the switch need to be in the same subnet. The switch needs an appropriate default gateway assigned. The switch interface connected to the router is down. Host needs to be assigned an IP address in VLAN 1. Correct Answer: C Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 87 Which condition does the err-disabled status indicate on an Ethernet interface? A. B. C. D. E. F. There is a duplex mismatch. The device at the other end of the connection is powered off. The serial interface is disabled. The interface is configured with the shutdown command. Port security has disabled the interface. The interface is fully functioning. Correct Answer: E Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 88 Which two correctly describe steps in the OSI data encapsulation process? (Choose two.) A. The presentation layer translates bits into voltages for transmission across the physical link. B. The data link layer adds physical source and destination addresses and an FCS to the segment. C. Packets are created when the network layer adds Layer 3 addresses and control information to a segment. D. Packets are created when the network layer encapsulates a frame with source and destination host addresses and protocol-related control information. E. The transport layer divides a data stream into segments and may add reliability and flow control information. Correct Answer: CE Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 89 Refer to the exhibit All of the routers in the network are configured with the ip subnet-zero command. Which network addresses should be used for Link A and Network A? (Choose two.) A. B. C. D. E. F. Link A 172.16.3.0/30 Link A 172.16.3.112/30 Network A 172.16.3.48/26 Network A 172.16.3.128/25 Link A 172.16.3.40/30 Network A 172.16.3.192/26 Correct Answer: AD Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 90 Which type of device can be replaced by the use of subinterfaces for VLAN routing ? A. B. C. D. Layer 2 bridge Layer 2 switch Layer 3 switch router Correct Answer: C Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 91 Which statement about LLDP is true? A. B. C. D. It is a Cisco proprietary protocol. It is configured in global configuration mode. The LLDP update frequency is a fixed value. It runs over the transport layer. Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 92 If the primary root bridge experiences a power loss, which switch takes over? A. B. C. D. switch 0040.00.90C5 switch 00E0.F90B.6BE3 switch 0004.9A1A.C182 switch 00E0.F726.3DC6 Correct Answer: C Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 93 A network administrator is troubleshooting an EIGRP problem on a router and needs to confirm the IP addresses of the devices with which the router has established adjacency. The retransmit interval and the queue counts for the adjacent routers also need to be checked. What command will display the required information? A. B. C. D. Router# show ip eigrp neighbors Router# show ip eigrp interfaces Router# show ip eigrp adjacency Router# show ip eigrp topology Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 94 Which three statements about IPv6 prefixes are true? (Choose three.) A. B. C. D. E. F. FEC0::/10 is used for IPv6 broadcast. FC00::/7 is used in private networks. FE80::/8 is used for link-local unicast. FE80::/10 is used for link-local unicast. 2001::1/127 is used for loopback addresses. FF00::/8 is used for IPv6 multicast. Correct Answer: BDF Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 95 Which command can you enter to display duplicate IP addresses that the DHCP server assigns? A. B. C. D. show ip dhcp conflict 10.0.2.12 show ip dhcp database 10.0.2.12 show ip dhcp server statistics show ip dhcp binding 10.0.2.12 Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 96 Which three ports will be STP designated ports if all the links are operating at the same bandwidth? (Choose three.) A. B. C. D. E. F. Switch B - F0/0 Switch A - Fa0/1 Switch B - Fa0/l Switch C - F0/1 Switch A - Fa0/0 Switch C - Fa0/0 Correct Answer: ABC Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 97 Refer to the exhibit The network administrator cannot connect to Switch 1 over a Telnet session, although the hosts attached to Switch1 can ping the interface Fa0/0 of the router. Given the information in the graphic and assuming that the router and Switch2 are configured properly, which of the following commands should be issued on Switch1 to correct this problem? A. B. C. D. E. Switch1(config)# ip default-gateway 192.168.24.1 Switch1(config)# interface fa0/1Switch1(config-if)# switchport mode trunk Switch1(config)# line con0Switch1(config-line)# password ciscoSwitch1(config-line)# login Switch1(config)# interface fa0/1Switch1(config-if)# ip address 192.168.24.3 255.255.255.0 Switch1(config)# interface fa0/1Switch1(config-if)# duplex fullSwitch1(confiq-if)# speed 100 Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 98 Refer to the exhibit. Each of these four switches has been configured with a hostname, as well as being configured to run RSTP.No other configuration changes have been made. Which three of these show the correct RSTP port roles for the indicated switches and interfaces? (Choose three.) A. B. C. D. E. F. SwitchD. Gi0/2, root SwitchA, Fa0/2, designated SwitchB, Gi0/l, designated SwitchA, Fa0/l, root SwitchB, Gi0/2, root SwitchC, Fa0/2, root Correct Answer: ABD Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 99 Which feature builds a FIB and an adjacency table to expedite packet forwarding? A. B. C. D. cut through fast switching process switching Cisco Express Forwarding Correct Answer: D Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 100 Which command can you enter to verify that a 128-bit address is live and responding? A. B. C. D. traceroute telnet ping show ipv6 Correct Answer: C Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 101 What are two reasons that duplex mismatches can be difficult to diagnose? (Choose two.) A. B. C. D. E. The interface displays a connected (up/up) state even when the duplex settings are mismatched. 1-Gbps interfaces are full-duplex by default. Full-duplex interfaces use CSMA/CD logic, so mismatches may be disguised by collisions. The symptoms of a duplex mismatch may be intermittent. Autonegotiation is disabled. Correct Answer: AD Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 102 Which condition indicates that service password-encryption is enabled? A. B. C. D. The local username password is in clear text in the configuration. The enable secret is in clear text in the configuration. The local username password is encrypted in the configuration. The enable secret is encrypted in the configuration. Correct Answer: C Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 103 Which protocol advertises a virtual IP address to facilitate transparent failover of a Cisco routing device? A. B. C. D. FHRP DHCP RSMLT ESRP Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 104 What is the correct routing match to reach 172.16.1.5/32 ? A. B. C. D. 172.16.1.0/26 172.16.1.0/25 172.16.1.0/24 the default route Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 105 Which layer in the OSI reference model is responsible for determining the availability of the receiving program and checking to see if enough resources exist for that communication? A. B. C. D. E. transport network presentation session application Correct Answer: E Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 106 What is the purpose of the POST operation on a router ? A. B. C. D. determine whether additional hardware has been added locate an IOS image for booting enable a TFTP server set the configuration register Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 107 Which protocol is the Cisco proprietary implementation of FHRP ? A. B. C. D. HSRP VRRP GLBP CARP Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 108 Which three characteristics are representative of a link-state routing protocol? (Choose three.) A. B. C. D. E. provides common view of entire topology exchanges routing tables with neighbors calculates shortest path utilizes event-triggered updates utilizes frequent periodic updates Correct Answer: ACD Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 109 Which part of the PPPoE server configuration contains the information used to assign an IP address to a PPPoE client? A. B. C. D. virtual-template interface DHCP dialer interface AAA authentication Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 110 A. Correct Answer: A Section: (none) Explanation Explanation/Reference: FF02::1 ------------ All Nodes (link-local) FF02::5 ------------ OSPFv3 Routers FF02::6 ------------ OSPFv3 Designated Routers FF02::A ------------ EIGRPv3 Routers FF02::D ------------ PIM Routers FF05::2 ------------ All Routers (site-local) QUESTION 111 Which three statements about RSTP are true? (Choose three.) A. B. C. D. E. F. RSTP significantly reduces topology reconverging time after a link failure. RSTP expands the STP port roles by adding the alternate and backup roles. RSTP port states are blocking, discarding, learning, or forwarding. RSTP provides a faster transition to the forwarding state on point-to-point links than STP does. RSTP also uses the STP proposal-agreement sequence. RSTP uses the same timer-based process as STP on point-to-point links Correct Answer: ABD Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 112 What are two benefits of using NAT? (Choose two.) A. B. C. D. E. F. NAT facilitates end-to-end communication when IPsec is enabled. NAT eliminates the need to re-address all hosts that require external access. NAT conserves addresses through host MAC-level multiplexing. Dynamic NAT facilitates connections from the outside of the network. NAT accelerates the routing process because no modifications are made on the packets. NAT protects network security because private networks are not advertised. Correct Answer: BF Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 113 Which two commands correctly verify whether port security has been configured on port FastEthernet 0/12 on a switch? (Choose two.) A. SW1#show port-secure interface FastEthernet 0/12 B. SW1#show switchport port-secure interface FastEthernet 0/12 C. SW1#show running-config D. SW1#show port-security interface FastEthernet 0/12 E. SW1#show switchport port-security interface FastEthernet 0/12 Correct Answer: CD Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 114 Refer to the exhibit. Given this output for SwitchC, what should the network administrator's next action be? A. B. C. D. Check the trunk encapsulation mode for Switch C's fa0/1 port. Check the duplex mode for Switch C's fa0/1 port. Check the duplex mode for Switch A's fa0/2 port. Check the trunk encapsulation mode for Switch A's fa0/2 port Correct Answer: C Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 115 Which statement is correct regarding the operation of DHCP ? A. B. C. D. A DHCP client uses a ping to detect address conflicts. A DHCP server uses a gratuitous ARP to detect DHCP clients. A DHCP client uses a gratuitous ARP to detect a DHCP server. If an address conflict is detected, the address is removed from the pool and an administrator must resolve the conflict. E. If an address conflict is detected, the address is removed from the pool for an amount of time configurable by the administrator. F. If an address conflict is detected, the address is removed from the pool and will not be reused until the server is rebooted. Correct Answer: D Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 116 Which two statements about using the CHAP authentication mechanism in a PPP link are true ? (Choose two.) A. B. C. D. E. F. CHAP uses a two-way handshake. CHAP uses a three-way handshake. CHAP authentication periodically occurs after link establishment. CHAP authentication passwords are sent in plaintext. CHAP authentication is performed only upon link establishment. CHAP has no protection from playback attacks. Correct Answer: BC Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 117 Refer to the exhibit. Switch port FastEthernet 0/24 on ALSwitch1 will be used to create an IEEE 802.1Q-compliant trunk to another switch. Based on the output shown, what is the reason the trunk does not form, even though the proper cabling has been attached? A. B. C. D. E. VLANs have not been created yet. An IP address must be configured for the port. The port is currently configured for access mode. The correct encapsulation type has not been configured. The no shutdown command has not been entered for the port. Correct Answer: C Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 118 Refer to the exhibit. A junior network administrator was given the task of configuring port security on SwitchA to allow only PC_A to access the switched network through port fa0/1. If any other device is detected, the port is to drop frames from this device. The administrator configured the interface and tested it with successful pings from PC_A to RouterA, and then observes the output from these two show commands. Which two of these changes are necessary for SwitchA to meet the requirements? (Choose two.) A. B. C. D. E. F. Port security needs to be globally enabled. Port security needs to be enabled on the interface. Port security needs to be configured to shut down the interface in the event of a violation. Port security needs to be configured to allow only one learned MAC address. Port security interface counters need to be cleared before using the show command. The port security configuration needs to be saved to NVRAM before it can become active. Correct Answer: BD Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 119 Which three statements about static routing are true? (Choose three.) A. B. C. D. E. F. It uses consistent route determination. It is best used for small-scale deployments. Routing is disrupted when links fail. It requires more resources than other routing methods. It is best used for large-scale deployments. Routers can use update messages to reroute when links fail. Correct Answer: ABC Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 120 What are the address that will show at the show ip route if we configure the above statements? (Choose Three.) A. B. C. D. E. F. 10.0.0.0 10.4.3.0 172.15.4.0 172.15.0.0 192.168.4.0 192.168.0.0 Correct Answer: ADE Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 121 Which feature facilitates the tagging of frames on a specific VLAN ? A. B. C. D. Routing Hairpinning Encapsulation Switching Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 122 What does split horizon prevent? A. B. C. D. routing loops, link state routing loops, distance vector switching loops, STP switching loops, VTP Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 123 Which value to use in HSRP protocol election process ? A. B. C. D. interface virtual IP address priority router ID Correct Answer: C Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 124 Which of the following is needed to be enable back the role of active in HSRP ? A. B. C. D. prempt priority other options other options Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 125 Which command is used to show the interface status of a router ? A. B. C. D. show interface status show ip interface brief show ip route show interface Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 126 Which of the following privilege level is the most secured ? A. B. C. D. Level 0 Level 1 Level 15 Level 16 Correct Answer: C Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 127 Which IPV6 feature is supported in IPV4 but is not commonly used ? A. B. C. D. unicast multicast anycast broadcast Correct Answer: C Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 128 Which two statements are true about IPv6 Unique Local Addresses ? (Choose Two.) A. B. C. D. It is the counterpart of IPv4 private addresses It uses FC00::/7 as prefix wrong wrong Correct Answer: AB Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 129 Which range represents the standard access list ? A. B. C. D. 99 150 299 2000 Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 130 What to do when the router password was forgotten ? A. B. C. D. use default password cisco to reset access router physically use ssl/vpn Type confreg 0x2142 at the rommon 1 Correct Answer: D Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 131 What is true about Cisco Discovery Protocol ? A. B. C. D. it discovers the routers, switches and gateways. it is network layer protocol it is physical and data link layer protocol it is proprietary protocol Correct Answer: D Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 132 Which of the following encrypts the traffic on a leased line ? A. telnet B. ssh C. vtp D. vpn E. dmvpn Correct Answer: D Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 133 How do you configure a hostname ? A. Router(config)#hostname R1 Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 134 How do you maintain security in multiple websites? A. B. C. D. vpn dmvpn other other Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 135 Refer to the exhibit. Switch-1 needs to send data to a host with a MAC address of 00b0.d056.efa4. What will Switch-1 do with this data? A. B. C. D. Switch-1 will drop the data because it does not have an entry for that MAC address. Switch-1 will flood the data out all of its ports except the port from which the data originated. Switch-1 will send an ARP request out all its ports except the port from which the data originated. Switch-1 will forward the data to its default gateway. Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 136 interface fa0/0 ip address x.x.x.33 255.255.255.224 router bgp XXX neighbor x.x.x.x remote as x.x.x.x You need to advertise the network of Int fa0/0. A. B. C. D. x.x.x.32 mask 255.255.255.224 x.x.x.32 255.255.255.224 x.x.x.32 mask 0.0.0.31= x.x.x.33 mask 255.255.255.224 Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 137 What routing protocol use first-hand information ? A. link-state B. distance-vector C. path-vector D. other Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 138 What field is consist of 6 bytes in the field identification frame in IEEE 802.1Q ? A. B. C. D. SA DA FCS other Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 139 What is new in HSRPv2 ? A. B. C. D. prempt a greater number in hsrp group field other other Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 140 What's are true about MPLS ? A. B. C. D. It use a label to separete traffic from several costumer It use IPv4 IPv6 other other Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 141 A network engineer wants to allow a temporary entry for a remote user with a specific username and password so that the user can access the entire network over the internet. Which ACL can be used? A. B. C. D. reflexive extended standard dynamic Correct Answer: D Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 142 Which command is necessary to permit SSH or Telnet access to a cisco switch that is otherwise configured for these vty line protocols ? A. B. C. D. transport type all transport output all transport preferred all transport input all Correct Answer: D Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 143 What should be part of a comprehensive network security plan ? A. Allow users to develop their own approach to network security B. Physically secure network equipment from potential access by unauthorized individuals C. Encourage users to use personal information in their passwords to minimize the likelihood of passwords being forgotten D. Delay deployment of software patches and updates until their effect on end-user equipment is well known and widely reported E. Minimize network overhead by deactivating automatic antivirus client updates Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 144 Which two Cisco IOS commands, used in troubleshooting, can enable debug output to a remote location ? (Choose two) A. B. C. D. E. no logging console logging host ip-address terminal monitor show logging | redirect flashioutput.txt snmp-server enable traps syslog Correct Answer: BC Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 145 Which component of the Cisco SDN solution serves as the centralized management system ? A. B. C. D. Cisco OpenDaylight Cisco ACI Cisco APIC Cisco IWAN Correct Answer: C Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 146 What command can you enter in config mode to create DHCP pool ? A. B. C. D. ip dhcp pool DHCP_pool ip dhcp exclude -add ip dhcp conflict logging service dhcp Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 147 Which utility can you use to determine whether a switch can send echo requests and replies? A. B. C. D. ping traceroute ssh telnet Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 148 What is the two benefits of DHCP snooping ? (Choose two) A. B. C. D. static reservation DHCP reservation prevent DHCP rouge server prevent untrusted host and servers to connect Correct Answer: CD Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 149 What are the three major components of cisco network virtualization ? (Choose Three) A. B. C. D. network access control path isolation virtual network services policy enforcement Correct Answer: ABC Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 150 Which feature is config by setting a variance that is at least 2 times the metric ? A. B. C. D. unequal cost load balancing path selection equal cost load balancing path count Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 151 Standard industrialized protocol of etherchannel ? A. B. C. D. LACP PAGP PRP REP Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 152 Two features of the extended ping command ? (Choose two) A. B. C. D. It can send a specific number of packet It can send packet from specified interface of IP address It can resolve the destination host name It can ping multiple host at the same time Correct Answer: AB Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 153 What command is used to configure a switch as authoritative NTP server ? A. B. C. D. Switch(config)#ntp master 3 Switch(config)#ntp peer IP Switch(config)#ntp server IP Switch(config)#ntp source IP Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 154 Which two statements about syslog logging are true? A. B. C. D. E. Syslog logging is disabled by default Messages are stored in the internal memory of device Messages can be erased when device reboots Messages are stored external to the device The size of the log file is dependent on the resources of the device. Correct Answer: AD Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2960/software/release/12-2_55_se/ configuration/guide/scg_2960/swlog.html “By default, a switch sends the output from system messages and debug privileged EXEC commands to a _logging process_.” “The _logging process_ controls the distribution of logging messages to various destinations, such as the logging buffer, terminal lines, or a UNIX _syslog_ server, depending on your configuration. The process also sends messages to the console.” Reading through parts of the reference should make it clear, that “syslog logging” is not the same as “System Message Logging”. “System Message Logging” is enabled by default and sends messages to the so called “logging process”. This then sends it to console, a buffer, or even a syslog Server (this part is not configured by default = “syslog logging” is not enabled by default). Now the “logging synchronous” comes in, when all the messages showing up in your console get in the way of you, typing in commands, since the displaying of messages jumbles up your inputs QUESTION 155 How to enable vlans automatically across multiple switches ? A. B. C. D. Configure VLAN Confiture NTP Configure each VLAN Configure VTP Correct Answer: D Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 156 Which password types are encrypted ? A. B. C. D. SSH Telnet enable secret enable password Correct Answer: C Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 157 What is the benefit of point-to-point leased line ? (Choose two.) A. B. C. D. Low cost Full-mesh capability Flexibillity of design Simply configuration Correct Answer: CD Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 158 What is the binary pattern of unique ipv6 unique local address ? A. B. C. D. 00000000 11111100 11111111 11111101 Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 159 Which statemnet about ACLs is true ? A. B. C. D. An ACL have must at least one permit action, else it just blocks all traffic. ACLs go bottom-up through the entries looking for a match An ACL has a an implicit permit at the end of ACL. ACLs will check the packet against all entries looking for a match. Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 160 What is the cause of the Syslog output messages ? A. The EIGRP neighbor on Fa0/1 went down due to a failed link. B. The EIGRP neighbor connected to Fa0/1 is participating in a different EIGRP process, causing the adjacency to go down. C. A shut command was executed on interface Fa0/1, causing the EIGRP adjacency to go down. D. Interface Fa0/1 has become error disabled, causing the EIGRP adjacency to go down. Correct Answer: C Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 161 What are contained in layer 2 ethernet frame ? (Choose Three.) A. B. C. D. E. F. Preamble TTL Type/length Frame check sequence version others Correct Answer: ACD Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 162 Describe the best way to troubleshoot and isolate a network problem ? A. Create an action plan B. Implement an action plan C. Gather facts D. others Correct Answer: A Section: (none) Explanation Explanation/Reference: http://www.cisco.com/en/US/docs/internetworking/troubleshooting/guide/tr1901.html QUESTION 163 Under normal operations, cisco recommends that you configure switch ports on which vlan ? A. B. C. D. on the default vlan on the management vlan on the native vlan on any vlan except the default vlan Correct Answer: A Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/support/docs/switches/catalyst-6500-series-switches/24330-185.html QUESTION 164 Which DTP switchport mode allow the port to create a trunk port if the the port is in trunk, dynamic auto and dynamic desirable mode ? A. B. C. D. Dynamic Auto Dynamic Desirable Access Trunk Correct Answer: A Section: (none) Explanation Explanation/Reference: http://bradhedlund.com/2007/11/27/switchport-configurations-explained/ QUESTION 165 In which byte of an IP packet can traffic be marked ? A. B. C. D. the QoS byte the CoS byte the ToS byte the DSCP byte Correct Answer: D Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/support/docs/quality-of-service-qos/qos-packet-marking/10103dscpvalues.html QUESTION 166 Which command can you enter to route all traffic that is destined to 192.168.0.0/20 to a specific interface ? A. B. C. D. ip route 192.168.0.0 255.255.240.0 gi 0/1 ip route 192.168.0.0 255.255.255.0 gi 0/1 ip route 0.0.0.0 0.0.0.0 gi 0/1 ip route 0.0.0.0 255.255.255.0 gi 0/1 Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 167 Which two protocol can detect native vlan mismatch errors? (Choose two.) A. B. C. D. E. CDP VTP DTP STP PAGP Correct Answer: AB Section: (none) Explanation Explanation/Reference: QUESTION 168 Which three options are switchport config that can always avoid duplex mismatch error between the switches? (Choose Three.) A. B. C. D. E. F. set both side on auto-negotation. set both sides on half-duplex set one side auto and other side half-duplex set both side of connection to full-duplex set one side auto and other side on full-duplex set one side full-duplex and other side half-duplex Correct Answer: ABD Section: (none) Explanation Explanation/Reference: http://www.pathsolutions.com/network-enemy-1-duplex-mismatch/ QUESTION 169 What are two benefits of Private IPv4 Addresses? (Choose two.) A. they can be implemented without requiring admin to coordinate with IANA B. they are managed by IANA C. increase the flexibility of network design D. provide network isloation from the internet E. they are routable over internet Correct Answer: AD Section: (none) Explanation Explanation/Reference: http://smallbusiness.chron.com/advantages-disadvantages-using-private-ip-address-space-46424.html QUESTION 170 How many bits represent network id in a IPv6 address ? A. B. C. D. 32 48 64 128 Correct Answer: C Section: (none) Explanation Explanation/Reference: http://networkengineering.stackexchange.com/questions/30836/calculate-networking-bits-for-ipv6 64 bits for Nwtwork ID and 64 bits for Interface ID 64+64=128 QUESTION 171 An interface which we have to determine from the routing the route learned by which routing protocol? A. B. C. D. EIGRP OSPF RIP BGP Correct Answer: A Section: (none) Explanation Explanation/Reference: (An image on exhibit) QUESTION 172 Which WAN topology is most appropriate for a centrally located server farm with several satellite branches ? A. B. C. D. star hub and spoke point-to-point full mesh Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: In a Hub-and-spoke Site-to-Site Wide Area Network (WAN) network topology, one physical site act as Hub (Example, Main Office), while other physical sites act as spokes. Spoke sites are connected to each other via Hub site. In Huband-spoke Wide Area Network (WAN) topology, the network communication between two spokes always travels through the hub. QUESTION 173 Which function allows EIGRP peers to receive notice of implementing topology changes? A. B. C. D. successors advertised changes goodbye messages expiration of the hold timer Correct Answer: C Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 174 If you configure syslog messages without specifying the logging trap level, which log messages will the router send ? A. B. C. D. E. informational messages only warning and error conditions only normal but significant conditions only error conditions only all levels except debugging Correct Answer: E Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 175 Which three options are benefits of using TACACS+ on a device? (Choose three) A. B. C. D. E. F. It ensures that user activity is untraceable. It provides a secure accounting facility on the device. device-administration packets are encrypted in their entirely. It allows the user to remotely access devices from other vendors. It allows the users to be authenticated against a remote server. It supports access-level authorization for commands. Correct Answer: CEF Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: http://tacacs.net/docs/TACACS_Advantages.pdf http://www.cisco.com/c/en/us/support/docs/security-vpn/remote-authentication-dial-userserviceradius/13838- 10.html QUESTION 176 What layer of the OSI Model is included in TCP/IP Model's INTERNET layer ? A. B. C. D. E. Application Session Data Link Presentation Network Correct Answer: E Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: NOT SURE ABOUT THE CHOICES. NOT SURE ABOUT THE QUESTION EITHER. QUESTION 177 Which two of these are characteristics of the 802.1Q protocol? (Choose two.) A. It is used exclusively for tagging VLAN frames and does not address network reconvergence following switched network topology changes. B. It modifies the 802.3 frame header, and thus requires that the FCS be recomputed. C. It is a Layer 2 messaging protocol which maintains VLAN configurations across networks. D. It includes an 8-bit field which specifies the priority of a frame. E. It is a trunking protocol capable of carrying untagged frames. Correct Answer: BE Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 178 Which two features can dynamically assign IPv6 addresses? (Choose two.) A. IPv6 stateless autoconfiguration B. DHCP C. NHRP D. IPv6 stateful autoconfiguration E. ISATAP tunneling Correct Answer: AB Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 179 A security administrator wants to profile endpoints and gain visibility into attempted authentications. Which 802.1x mode allows these actions ? A. B. C. D. Monitor mode High-Security mode Low-impact mode Closed mode Correct Answer: A Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: QUESTION 180 How to verify strong and secured SSH connection ? A. B. C. D. ssh -v 1 -l admin 10.1.1.1 ssh -v 2 -l admin 10.1.1.1 ssh -l admin 10.1.1.1 ssh v 2 admin 10.1.1.1 Correct Answer: B Section: (none) Explanation Explanation/Reference: Section: (none) Explanation Explanation/Reference: Sorry for the question but they said it was something like that. QUESTION 181 How many usable host are there per subnet if you have the address of 192.168.10.0 with a subnet mask of 255.255.255.240 ? A. B. C. D. 4 8 16 14 Correct Answer: D Section: (none) Explanation Explanation/Reference: QUESTION 182 What interconnection cable can you use when you use a MDI connection ? A. B. C. D. cut-through straight-through crossover rollover Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 183 Which cisco platform can verify ACLs ? A. B. C. D. Cisco Prime Infrastructure Cisco Wireless LAN Controller Cisco APIC-EM Cisco IOS-XE Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 184 In order to comply with new auditing standards, a security administrator must be able to correlate system security alert logs directly with the employee who triggers the alert. Which of the following should the security administrator implement in order to meet this requirement? A. B. C. D. Access control lists on file servers Elimination of shared accounts Group-based privileges for accounts Periodic user account access reviews Correct Answer: D Section: (none) Explanation Explanation/Reference: QUESTION 185 When you deploy multilink PPP on your network, where must you configure the group IP Address on each device ? A. B. C. D. In the global config Under serial interface Under the routing protocol Under the multilink interface Correct Answer: D Section: (none) Explanation Explanation/Reference: QUESTION 186 If you want multiple hosts on a network, where do you configure the setting ? A. B. C. D. in the IP protocol in the multicast interface in the serial interface in the global configuration Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 187 Which option is the benefit of implementing an intelligent DNS for a cloud computing solution ? A. B. C. D. It reduces the need for a backup data center. It can redirect user requests to locations that are using fewer network resources. It enables the ISP to maintain DNS records automatically. It eliminates the need for a GSS. Correct Answer: B Section: (none) Explanation Explanation/Reference: QUESTION 188 Which statement about the IP SLAs ICMP Echo operation is true? A. B. C. D. The frequency of the operation .s specified in milliseconds. It is used to identify the best source interface from which to send traffic. It is configured in enable mode. It is used to determine the frequency of ICMP packets. Correct Answer: D Section: (none) Explanation Explanation/Reference: QUESTION 189 Which action can change the order of entries in a named access-list ? A. B. C. D. removing an entry opening the access-list in notepad adding an entry resequencing Correct Answer: D Section: (none) Explanation Explanation/Reference: QUESTION 190 How does a router handle an incoming packet whose destination network is missing from the routing table ? A. B. C. D. it broadcast the packet to each interface on the router it discards the packet it broadcasts the packet to each network on the router it routes the packet to the default Correct Answer: B Section: (none) Explanation Explanation/Reference: QUESTION 191 Which two components are used to identify a neighbor in a BGP configuration? (Choose two.) A. B. C. D. E. autonomous system number version number router ID subnet mask IP address Correct Answer: AE Section: (none) Explanation Explanation/Reference: QUESTION 192 Which three statements about HSRP operation are true? (Choose three.) ? A. B. C. D. The virtual IP address and virtual MAC address are active on the HSRP Master router. The HSRP default timers are a 3 second hello interval and a 10 second dead interval. HSRP supports only clear-text authentication The HSRP virtual IP address must be on a different subnet than the routers’ interfaces on the same LAN. E. The HSRP virtual IP address must be the same as one of the router’s interface addresses on the LAN. F. HSRP supports up to 255 groups per interface, enabling an administrative form of load balancing. Correct Answer: ABF Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/support/docs/ip/hot-standby-router-protocol-hsrp/10583-62.html#topic5 “The active router sources hello packets from its configured IP address and the HSRP virtual MAC address. The standby router sources hellos from its configured IP address and the burned-in MAC address (BIA).” http://www.cisco.com/c/en/us/support/docs/ip/hot-standby-router-protocol-hsrp/10583-62.html#topic14 “By default, these timers are set to 3 and 10 seconds, respectively…” http://www.cisco.com/c/en/us/support/docs/switches/catalyst-6000-series-switches/29545-168.html#q1 Load Sharing with HSRP http://www.cisco.com/c/en/us/support/docs/ip/hot-standby-router-protocol-hsrp/13781-7.html#conf “…has a 256 unique HSRP group ID limit.” “…the allowed group ID range (0-255). … MSFC2A (Supervisor Engine 32) can use any number of group IDs from that range. QUESTION 193 Which two options describe benefits of aggregated chassis technology ( choose 2) ? A. B. C. D. E. F. it reduces management overhead. switches can be located anywhere regardless of there physical location. it requires only 1 IP add per VLAN. it requires only 3 IP add per VLAN. it supports HSRP VRRP GLBP. it support redundant configuration files. Correct Answer: AC Section: (none) Explanation Explanation/Reference: QUESTION 194 How to trouble DNS issue ( choose two) ? A. B. C. D. E. Ping a public website IP address. Ping the DNS Server. Determine whether a DHCP address has been assigned. Determine whether the hardware address is correct. Determine whether the name servers have been configured. Correct Answer: BC Section: (none) Explanation Explanation/Reference: https://l.facebook.com/l.php?u=http%3A%2F%2Fwww.cisco.com%2Fen%2FUS%2Fdocs% 2Finternetworking%2Ftroubleshooting%2Fguide%2Ftr1907.html% 23wp1021264&h=ATMT6hWMWKar6G3cbMd8vYoG64obKG4CIuxXlmCWtCLencP9vUG0hrC3C0azv18a RsmIsdrKko8ew_O6UkUwYCVqgYvxTz3TFquXNKyrnrAa1arE1V4HBFjg4_E2gJSawoz2_g Ping the destination by name perform a DNS lookup on the destination QUESTION 195 Which utility can you use to identify redundant or shadow rules ? A. B. C. D. The ACL trace tool in Cisco APIC-EM. The ACL analysis tool in Cisco APIC-EM. The Cisco APIC-EM automation scheduler. The Cisco IWAN application. Correct Answer: B Section: (none) Explanation Explanation/Reference: QUESTION 196 What does traffic shaping do to reduce congestion in a network? A. B. C. D. buffers and queues packets. buffers without queuing packets. queqes without buffering packets. drops packets. Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 197 Which 2 statements about extended traceroute command is true? A. B. C. D. E. it can send packets from specified interface or ip add. it can use a specified TTL value. it can validate the reply data. it can use a specificed TOS. it can repeated automatically to a specified interval. Correct Answer: AB Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/support/docs/ip/routing-information-protocol-rip/13730-extpingtrace.html#ext_troute “This table lists the traceroute command field descriptions: Source address: The interface or IP address of the router to use as a source address for the probes. The router normally picks the IP address of the outbound interface to use. Minimum Time to Live [1]: The TTL value for the first probes. The default is 1, but it can be set to a higher value to suppress the display of known hops. Maximum Time to Live [30]: The largest TTL value that can be used. The default is 30. The traceroute command terminates when the destination is reached or when this value is reached. QUESTION 198 A BPDU guard is configured on an interface that has PortFast Enable. Which state does the interface enter when it recives a BPDU ? A. B. C. D. Blocking. Shutdown. Listening. Errdisable. Correct Answer: D Section: (none) Explanation Explanation/Reference: QUESTION 199 Which command can you enter to determine the addresses that have been assigned on a DHCP Server? A. B. C. D. Show ip DHCP database. Show ip DHCP pool. Show ip DHCP binding. Show ip DHCP server statistic. Correct Answer: C Section: (none) Explanation Explanation/Reference: http://www.aubrett.com/InformationTechnology/RoutingandSwitching/Cisco/CiscoRouters/ DHCPBindings.aspx “Router#show ip dhcp binding Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type 10.16.173.0 24d9.2141.0ddd Jan 12 2013 03:42 AM Automatic” QUESTION 200 Which statement about SNMPv2 is true ? A. B. C. D. Its privacy algorithms use MD5 encryption by default. it requires passwords to be encrypyed. Its authetication and privacy algorithms are enable without default values. It requires passwords at least eight characters en length. Correct Answer: C Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/td/docs/ios/12_2/configfun/configuration/guide/ffun_c/ fcf014.html#wp1010901 “Model___Level_________Authentication_____Encryption__What Happens v2c_____noAuthNoPriv___Community String__No________Uses a community string match for authentication.” So B & D must be wrong, because there is no “password” in SNMPv2. A is wrong because there is no encryption in SNMPv2. QUESTION 201 which type of IP address of ipv6 that also exist in IPv4 but barely used? A. unicast. B. multicast. C. anycast. D. broadcast. Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 202 Which symptom most commonly indicates that 2 connecting interface are configured with a duplex mismatch? A. B. C. D. an int with up/down state. an int with down/down state. late collisions on the interface. the spanning tree process shutting down. Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 203 How Eigrp for ipv6 configuration done? ( choose 2) A. B. C. D. E. uses process number. neighbor configured directly. configured driectly on interface. configured globally interface. have shutdown feature. Correct Answer: CE Section: (none) Explanation Explanation/Reference: QUESTION 204 Which VTP mode can not make a change to vlan? A. B. C. D. Server. Client. Transparent. Off Correct Answer: B Section: (none) Explanation Explanation/Reference: VTP Client · VTP clients function the same way as VTP servers, but you cannot create, change, or delete VLANs on a VTP client. · A VTP client only stores the VLAN information for the entire domain while the switch is on. · A switch reset deletes the VLAN information. · You must configure VTP client mode on a switch. QUESTION 205 Which function does IP SLA ICMP ECHO operation perform to assist with troubleshooting? A. B. C. D. one way jitter measurement. congestion detection. hop-by-hop response time. packet-loss detection. Correct Answer: C Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipsla/configuration/15-mt/sla-15-mt-book/ sla_icmp_pathjitter.html QUESTION 206 Which mode are in PAgP? (choose two) A. B. C. D. E. Auto. Desirable. Active. Passive. On. Correct Answer: AB Section: (none) Explanation Explanation/Reference: http://www.omnisecu.com/cisco-certified-network-associate-ccna/etherchannel-pagp-and-lacp-modes.php QUESTION 207 What routing protocol use first-hand information from peers? A. B. C. D. link state. distance-vector. path-vector. other. Correct Answer: A Section: (none) Explanation Explanation/Reference: http://www.ciscopress.com/articles/article.asp?p=24090&seqNum=4 QUESTION 208 In an Ethernet network, under what two scenarios can devices transmit? (Choose two.) A. when they receive a special token. B. C. D. E. when there is a carrier. when they detect no other devices are sending. when the server grants access. when the medium is idle. Correct Answer: CE Section: (none) Explanation Explanation/Reference: QUESTION 209 Which two protocols are used by bridges and/or switches to prevent loops in a layer 2 network? (Choose two.) A. B. C. D. E. 802.1d VTP 802.1q SAP STP Correct Answer: AE Section: (none) Explanation Explanation/Reference: QUESTION 210 At which layer of the OSI model does PPP perform? A. B. C. D. E. Layer 2 Layer 3 Layer 4 Layer 5 Layer 1 Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 211 What are three reasons that an organization with multiple branch offices and roaming users might implement a Cisco VPN solution instead of point-to-point WAN links?(Choose three.) A. B. C. D. E. F. reduced cost. better throughput. broadband incompatibility. increased security. scalability. reduced latency. Correct Answer: ADE Section: (none) Explanation Explanation/Reference: QUESTION 212 Which two statements about IPv4 multicast traffic are true? (Choose two.) A. B. C. D. E. It burdens the source host without affecting remote hosts. It uses a minimum amount of network bandwidth. It is bandwidth-intensive. It simultaneously delivers multiple streams of data. It is the most efficient way to deliver data to multiple receivers. Correct Answer: DE Section: (none) Explanation Explanation/Reference: IP multicast is a bandwidth-conserving technology that reduces traffic by simultaneously delivering a single stream of information to potentially thousands of corporate recipients and homes. http://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/mcst_ovr.html QUESTION 213 Which IPv6 header field is equivalent to the TTL? A. B. C. D. E. Scan Timer. TTD. Flow Label. Hop Limit. Hop Count. Correct Answer: D Section: (none) Explanation Explanation/Reference: Time To Live (TTL)/Hop Limit (8 bits) http://ipv6.com/articles/general/IPv6-Header.htm QUESTION 214 which port security mode can assist with troubleshooting by keeping count of violations? A. B. C. D. access. protect. restrict. shutdown. Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 215 which 2 optns are requirements for configuring ripv2 for ipv4 (choose 2 ) ? A. B. C. D. E. enabling RIP authentication. connecting RIP to a WAN Interface. enabling auto route sumamrization. allowing unicast updates for RIP. enabling RIP on the router. Correct Answer: DE Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/td/docs/ios/12_2/ip/configuration/guide/fipr_c/1cfrip.html#wp1000889 “Enabling RIP (Required) Allowing Unicast Updates for RIP (Required)” RIP Version 1 and Version 2 have the same basic requirements! QUESTION 216 which configuration command can u apply to a hsrp router so that its local interface becomes ? A. B. C. D. E. active if all other routers in the group fail no additional config is required standby 1 track ethernet standby 1 preempt standby 1 priority 250 Correct Answer: D Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/support/docs/ip/enhanced-interior-gateway-routing-protocol-eigrp/113267eigrp-ipv6-00.html QUESTION 217 which 2 statements about extended traceroute command is true ? A. B. C. D. E. it can use a specified TTL value it can send packets from specified interface or ip add it can validate the reply data it can use a specificed TOS it can repeated automatically to a specified interval Correct Answer: AB Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/support/docs/ip/routing-information-protocol-rip/13730-extpingtrace.html#ext_troute “This table lists the traceroute command field descriptions: Source address: The interface or IP address of the router to use as a source address for the probes. The router normally picks the IP address of the outbound interface to use. Minimum Time to Live [1]: The TTL value for the first probes. The default is 1, but it can be set to a higher value to suppress the display of known hops. Maximum Time to Live [30]: The largest TTL value that can be used. The default is 30. The traceroute command terminates when the destination is reached or when this value is reached.” QUESTION 218 which statement about EIGRP on IPv6 device is true ? A. B. C. D. E. It is configured on the interface . It is globally configured . If is configured using a network statement . It is vendor agnostic. It supports a shutdown feature. Correct Answer: AE Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/support/docs/ip/enhanced-interior-gateway-routing-protocol-eigrp/113267eigrp-ipv6-00.html QUESTION 219 which command can you enter to troubleshoot the failure of address assignment ? A. B. C. D. sh ip dhcp database sh ip dhcp pool sh ip dhcp import sh ip dhcp server statistics Correct Answer: B Section: (none) Explanation Explanation/Reference: QUESTION 220 which three technical services support cloud computing ? A. B. C. D. E. F. network-monitored power sources layer 3 network routing ip localization redundant connections VPN connectivity extended SAN services Correct Answer: DEF Section: (none) Explanation Explanation/Reference: QUESTION 221 which two steps must you perform to enbale router- on- stick on a switch ? A. B. C. D. connect the router to a trunk port config the subint number exactly the same as the matching VLAN config full duplex cofigure an ip route to the vlan destn net E. assign the access port to the vlan Correct Answer: AB Section: (none) Explanation Explanation/Reference: QUESTION 222 which add prefix does OSPFv3 use when multiple IPv6 address are configured on a single interface ? A. all prefix on the interface B. the prefix that the administrator configure for OSPFv3 use C. the lowest prefix on the interface D. the highest prefix on the interface Correct Answer: A Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_ospf/configuration/15-sy/iro-15-sy-book/ip6routeospfv3.html#GUID-05F3F09C-FE3E-41D6-9845-111FB17AD030 “In IPv6, you can configure many address prefixes on an interface. In OSPFv3, all address prefixes on an interface are included by default. You cannot select some address prefixes to be imported into OSPFv3; either all address prefixes on an interface are imported, or no address prefixes on an interface are imported.” QUESTION 223 which IP configuration does the CIDR notation 192.168.1.1/25 refer ? A. B. C. D. E. 192.168.1.1 255.255.255.64 192.168.1.1 255.255.255.1 192.168.1.1 255.255.255.32 192.168.1.1 255.255.255.256 192.168.1.1 255.255.255.128 Correct Answer: E Section: (none) Explanation Explanation/Reference: QUESTION 224 CIDR notation (255.255.255.252 ) / notation ? A. B. C. D. 30 31 32 33 Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 225 Which two of these statements regarding RSTP are correct ? (Choose two) A. B. C. D. E. RSTP cannot operate with PVST+. RSTP defines new port roles. RSTP defines no new port states. RSTP is a proprietary implementation of IEEE 802.1D STP. RSTP is compatible with the original IEEE 802.1D STP. Correct Answer: BE Section: (none) Explanation Explanation/Reference: QUESTION 226 What is known as ―one-to-nearest addressing in IPv6 ? A. B. C. D. global unicast anycast multicast unspecified address Correct Answer: B Section: (none) Explanation Explanation/Reference: QUESTION 227 When a device learns multiple routes to a specific network, it installs the route with : A. B. C. D. Longest bit Match (highest subnet Mask) lowest AD lowest metric equal load balancing Correct Answer: B Section: (none) Explanation Explanation/Reference: http://www.ciscopress.com/articles/article.asp?p=2180208&seqNum=9 QUESTION 228 Requirement to configure DHCP binding ( 2 options) A. B. C. D. DHCP pool ip address Hardware address other option Correct Answer: BC Section: (none) Explanation Explanation/Reference: QUESTION 229 how to see dhcp conflict ? A. B. C. D. show ip dhcp pool show dhcp database show ip dhcp conflict Other Option. Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 230 Which Cisco platform can verify ACLs ? A. B. C. D. Cisco Prime Infrastructure Cisco Wireless LAN Controller Cisco APIC-EM Cisco IOS-XE Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 231 Which type of mac address learning age out? A. B. C. D. Dynamic Static Auto one more option Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 232 Which major component of the network virtualization architecture isolate users according to policy? A. B. C. D. policy enforcement network access control network services virtualization path isolation Correct Answer: B Section: (none) Explanation Explanation/Reference: Network access control and segmentation of classesof users: Users are authenticated and either allowed or denied into a logical partition. Users are segmented into employees, contractors and consultants, and guests, with respective access to IT assets. This component identifies users who are authorized toaccess the network and then places them into the appropriate logical partition. QUESTION 233 Which two statements about firewalls are true ? A. B. C. D. E. They can be used with an intrusion prevention system. They can limit unauthorized user access to protect data. Each wireless access point requires its own firewall. They must be placed only at locations where the private network connects to the internet. They can prevent attacks from the internet only. Correct Answer: AB Section: (none) Explanation Explanation/Reference: QUESTION 234 Which two statements about data VLANs on access ports are true ? ( Choose two) A. B. C. D. E. They can be configured as trunk ports. Two or more VLANs can be configured on the interface. 802.1Q encapsulation must be configured on the interface. Exactly one VLAN can be configured on the interface. They can be configured as host ports. Correct Answer: DE Section: (none) Explanation Explanation/Reference: QUESTION 235 Where does the configuration reside when a helper address is configured to support DHCP ? A. B. C. D. on the switch trunk interface. on the router closest to the client. on the router closest to the server. on every router along the path. Correct Answer: B Section: (none) Explanation Explanation/Reference: QUESTION 236 Which command can you enter to configure an IPV6 floating static route? A. B. C. D. Router(config)# ipv6 route static resolve default Router(config)# ipv6 route::/0 serail0/1 Router(config)# ipv6 route FE80:0202::/32 serail 0/1 201 Router(config)# ipv6 route FE80:0202::/32 serail 0/1 1 Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 237 How does NAT overloading provide one-to-many address translation? A. B. C. D. It uses a pool of addresses It converts IPV4 addresses to unused IPv6 Addresses assigns a unique TCP/UDP port to each session It uses virtual MAC Address and Virtual IP Addresses Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 238 Which three options are types of Layer 2 network attack ? (Choose three) A. B. C. D. E. F. Spoofing attacks Vlan Hopping botnet attacks DDOS attacks ARP Attacks Brute force attacks Correct Answer: ABE Section: (none) Explanation Explanation/Reference: QUESTION 239 What does split-horizon do? A. Prevent routing loop in distance vector protocol B. Prevent switching loop in distance vector protocol C. Prevent switching loop in link-state protocol D. Prevent routing loop in link-state protocol Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 240 Afar you apply the given configuration to R1, you notice that it failed to enable OSPF Which action can you take to correct the problem? A. B. C. D. Configure a loopback interface on R1 Enable IPv6 unicast routing on R1. Configure an IPv4 address on interface FO/0. Configure an autonomous system number on OSPF. Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 241 How many broadcast domains are shown in the graphic assuming only the default VLAN is confgured on the switches? A. B. C. D. one two six twelve Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 242 Which three statements correcctly describe Network Device A? (Choose three.) A. With a network wide mask B. With a network wide mask IP subnet. C. With a network wide mask each other. D. With a network wide mask each other. E. With a network wide mask Correct Answer: BDE of 255.255.255.128, each interface does not require an IP address. of 255.255.255.128, each interface does require an IP address on a unique of 255.255.255.0, must be a Layer 2 device for the PCs to communicate with of 255.255.255.0, must be a Layer 3 device for the PCs to communicate with of 255.255.254.0, each interface does not require an IP address. Section: (none) Explanation Explanation/Reference: QUESTION 243 At the end of an RSTP election process, which access layer switch port will assume the discarding role? A. B. C. D. E. F. Switch3, port fa0/1 Switch3, port fa0/12 Switch4, port fa0/11 Switch4, port fa0/2 Switch3, port Gi0/1 Switch3, port Gi0/2 Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 244 Why is flash memory erased prior to upgrading the IOS image from the TFTP server? A. B. C. D. The router cannot verify that the Cisco IOS image currently in flash is valid. Flash memory on Cisco routers can contain only a single IOS image. Erasing current flash content is requested during the copy dialog. In order for the router to use the new image as the default, it must be the only IOS image in flash. Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 245 The network shown in the diagram is experiencing connectivity problems. Which of the following will correct the problems? (Choose two.) A. B. C. D. E. F. Configure the gateway on Host A as 10.1.1.1 Configure the gateway on Host B as 10.1.2.254 Configure the IP address of Host A as 10.1.2.2 Configure the IP address of Host B as 10.1.2.2 Configure the masks on both hosts to be 255.255.255.224 Configure the masks on both hosts to be 255.255.255.240 Correct Answer: BD Section: (none) Explanation Explanation/Reference: QUESTION 246 Which utility can you use to identify the cause of a traffic-flow blockage between the two devices in a network? A. ACL path analysis tool in APIC-EM B. I WAN application C. ACL analysis tool in APIC-EM D. APIC-EM automation scheduler Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 247 Which IEEE mechanism is responsible for the authentication of devices when they attempt to connect to a local network? A. 802.1x B. 802.11 C. 802.2x D. 802.3x Correct Answer: A Section: (none) Explanation Explanation/Reference: IEEE 802.1X is an IEEE Standard for port-based Network Access Control (PNAC). It is part of the IEEE 802.1 group of networking protocols. It provides an authentication mechanism to devices wishing to attach to a LAN or WLAN QUESTION 248 When a router is unable to find a known route in the routing table, how does it handle the packet? A. It discards the packet B. It sends the packet over the route with the best metric C. It sends the packet to the next hop address D. It sends the packet to the gateway of last resort Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 249 If router R1 knows a static route to a destination network and then learns about the same destinationnetwork through a dynamic routing protocol, how does R1 respond? A. It refuses to advertise the dynamic route to other neighbors B. It sends a withdrawal signal to the neighboring router C. It disables the routing protocol D. It prefers the static route Correct Answer: D Section: (none) Explanation Explanation/Reference: By default the administrative distance of a static route is 1, meaning it will be preferred over all dynamic routing protocols. If you want to have the dynamic routing protocol used and have the static route be used only as a backup, you need to increase the AD of the static route so that it is higher than the dynamic routing protocol. QUESTION 250 Which two statements about floating static routes are true? (Choose two) A. They are routes to the exact /32 destination address B. They are used when a route to the destination network is missing C. They have a higher administrative distance than the default static route administrative distance D. They are used as back-up routes when the primary route goes down E. They are dynamic routes that are learned from a server Correct Answer: CD Section: (none) Explanation Explanation/Reference: QUESTION 251 Which port security mode can assist with troubleshooting by keeping count of violations? A. Restrict B. Shutdown C. Access D. Protect Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 252 What type of MAC address is aged automatically by the switch? A. Dynamic B. Manual C. Automatic D. Static Correct Answer: A Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/configuration/guide/cli/ CLIConfigurationGuide/MACAddress.htm QUESTION 253 What are the two minimum required components of a DHCP binding? (choose two) A. An exclusion list B. A hardware address C. An IP address D. A DHCP pool E. An ip-helper statement Correct Answer: BC Section: (none) Explanation Explanation/Reference: An address binding is the mapping between the client’s IP and hardware addresses. http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipaddr_dhcp/configuration/15-mt/dhcp-15-mt-book/ dhcpoverview.html QUESTION 254 Refer to the exhibit. If R1 receives a packet destined to 172.16.1.1, to which IP address does it send the packet ? A. B. C. D. 192.168.14.4 192.168.12.2 192.168.13.3 192.168.15.5 Correct Answer: A Section: (none) Explanation Explanation/Reference: It can't find the address 172.16.1.1 so it will be directed to the Gate of last resort 192.168.14.4 QUESTION 255 What is the danger of the permit any entry in a NAT access list? A. It can lead to overloaded resources on the router. B. It can cause too many addresses to be assigned to the same interface. C. It can disable the overload command. D. It prevents the correct translation of IP addresses on the inside network. Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 256 How does a DHCP server dynamically assign IP addresses to hosts ? A. Addresses are permanently assigned so that the host uses the same address at all times. B. Addresses are assigned for a fixed period of time. C. Addresses are leased to hosts. A host will usually keep the same address by periodically contacting the DHCP server to renew the lease. D. Addresses are allocated after a negotiation between the server and the host to determine the length of the agreement. Correct Answer: C Section: (none) Explanation Explanation/Reference: The DHCP lifecycle consists of the following: Release: The client may decide at any time that it no longer wishes to use the IP address it was assigned, and may terminate the lease, releasing the IP address. QUESTION 257 What two results would occur if the hub were to be replaced with a switch that is configured with one Ethernet VLAN? (Choose two.) A. The number of collision domains would remain the same. B. The number of collision domains would decrease. C. The number of collision domains would increase. D. The number of broadcast domains would remain the same. E. The number of broadcast domains would decrease. F. The number of broadcast domains would increase. Correct Answer: CD Section: (none) Explanation Explanation/Reference: QUESTION 258 which configuration command can u apply to a HSRP router so that its local interface becomes active if all other routers in the group fail? A. no additional config is required B. standby 1 track ethernet C. standby 1 preempt D. standby 1 priority 250 Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 259 Refer to the exhibit, you determine that Computer A cannot ping Computer Which reason for the problem is most likely true? A. The Subnet mask for Computer A is incorrect. B. The default gateway address for Computer A is incorrect. C. The subnet mask for computer B is incorrect. D. The default gateway address for computer B is incorrect. Correct Answer: A Section: (none) Explanation Explanation/Reference: 255.255.255.224 =/27 QUESTION 260 Which effect of the passive-interface command on R1 is true? A. B. C. D. It prevents interface Fa0/0 from sending updates. Interface Fa 0/0 operates in RIPv1 mode. It removes the 172.16.0.0 network from all updates on all interfaces on R1. It removes the 172.17.0.0 network from all updates on all interfaces on R1. Correct Answer: A Section: (none) Explanation Explanation/Reference: With most routing protocols, the passive-interface command restricts outgoing advertisements only. But, when used with Enhanced Interior Gateway Routing Protocol (EIGRP), the effect is slightly different. QUESTION 261 Which three encapsulation layers in the OSI model are combined into the TCP/IP application layer? (Choose three) A. B. C. D. E. F. Session transport presentation application data-link network Correct Answer: ACD Section: (none) Explanation Explanation/Reference: QUESTION 262 Which function does traffic shaping perform? A. It buffers and queues excess packets. B. It buffers traffic without queuing it. C. It queues traffic without buffering it. D. It drops packets to control the output rate. Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 263 After you apply the given configuration to R1, you notice that it failed to enable OSPF .Which action can you... A. Configure an IPv4 address on interface F0/0. B. Enable IPV6 unicast routing on R1. C. Configure a loopback interface on R1. D. Configure an autonomous system number an OSPF. Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 264 When is the most appropriate time to escalate an issue that you troubleshooting? A. When you lack the proper to resolve the issue. B. When a more urgent issue that requires your intervention is detected. C. When you have gathered all information about an issue. D. When you have been unable to resolve the issue after 30 min. Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 265 Which two command can you enter to display the current time sources statistics on devices ? (Choose TWO) A. Show ntp associations. B. Show clock details. C. Show clock. D. Show time. E. Show ntp status. Correct Answer: AE Section: (none) Explanation Explanation/Reference: QUESTION 266 When you enable PortFast on a switch port, the port immediately transitions to which state? A. Blocking B. Forwarding C. Learning D. Listening Correct Answer: B Section: (none) Explanation Explanation/Reference: PortFast causes a switch or trunk port to enter the spanning tree forwarding state immediately, bypassing the listening and learning states. You can use PortFast on switch or trunk ports that are connected to a single workstation, switch, or server to allow those devices to connect to the network immediately, instead of waiting for the port to transition from the listening and learning states to the forwarding state. 200-125 66q Number: 200-125 Passing Score: 810 Time Limit: 120 min File Version: 1.0 Thanks to ManhDT Kingsman Liam edited by Overlord Exam A QUESTION 1 Which three statements about HSRP operation are true? (Choose three.) A. B. C. D. The virtual IP address and virtual MAC address are active on the HSRP Master router. The HSRP default timers are a 3 second hello interval and a 10 second dead interval. HSRP supports only clear-text authentication The HSRP virtual IP address must be on a different subnet than the routers’ interfaces on the same LAN. E. The HSRP virtual IP address must be the same as one of the router’s interface addresses on the LAN. F. HSRP supports up to 255 groups per interface, enabling an administrative form of load balancing. Correct Answer: ABF Section: (none) Explanation Explanation/Reference: QUESTION 2 Which two options describe benefits of aggregated chassis technology ( choose 2) A. B. C. D. E. F. it reduces management overhead switches can be located anywhere regardless of there physical location it requires only 1 IP add per VLAN it requires only 3 IP add per VLAN it supports HSRP VRRP GLBP it support redundant configuration files Correct Answer: AC Section: (none) Explanation Explanation/Reference: QUESTION 3 How to trouble DNS issue ( choose two) A. B. C. D. E. Ping a public website IP address. Ping the DNS Server. Determine whether a DHCP address has been assigned. Determine whether the hardware address is correct. Determine whether the name servers have been configured Correct Answer: BC Section: (none) Explanation Explanation/Reference: QUESTION 4 Which utility can you use to identify redundant or shadow rules ? A. The ACL trace tool in Cisco APIC-EM. B. The ACL analysis tool in Cisco APIC-EM. C. The Cisco APIC-EM automation scheduler. D. The Cisco IWAN application. Correct Answer: B Section: (none) Explanation Explanation/Reference: QUESTION 5 What does traffic shaping do to reduce congestion in a network? A. B. C. D. buffers and queues packets buffers without queuing packets queqes without buffering packets drops packets Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 6 Which 2 statements about extended traceroute command is true? A. B. C. D. E. it can send packets from specified interface or ip add it can use a specified TTL value it can validate the reply data it can use a specificed TOS it can repeated automatically to a specified interval Correct Answer: AB Section: (none) Explanation Explanation/Reference: QUESTION 7 A BPDU guard is configured on an interface that has PortFast Enable. Which state does the interface enter when it recives a BPDU ? A. B. C. D. Blocking Shutdown. Listening. Errdisable. Correct Answer: D Section: (none) Explanation Explanation/Reference: QUESTION 8 Which command can you enter to determine the addresses that have been assigned on a DHCP Server? A. B. C. D. Show ip DHCP database Show ip DHCP pool Show ip DHCP binding Show ip DHCP server statistic Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 9 Which statement about SNMPv2 is true ? A. B. C. D. Its privacy algorithms use MD5 encryption by default. it requires passwords to be encrypyed. Its authetication and privacy algorithms are enable without default values. It requires passwords at least eight characters en length. Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 10 which type of IP address of ipv6 that also exist in IPv4 but barely used? A. B. C. D. unicast multicast anycast broadcast Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 11 Which symptom most commonly indicates that 2 connecting interface are configured with a duplex mismatch? A. B. C. D. an int with up/down state an int with down/down state late collisions on the interface the spanning tree process shutting down Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 12 How Eigrp for ipv6 configuration done? ( choose 2) A. B. C. D. E. uses process number neighbor configured directly configured driectly on interface configured globally interface have shutdown feature Correct Answer: CE Section: (none) Explanation Explanation/Reference: QUESTION 13 Which VTP mode can not make a change to vlan? A. B. C. D. Server Client Transparent Off Correct Answer: B Section: (none) Explanation Explanation/Reference: VTP Client · VTP clients function the same way as VTP servers, but you cannot create, change, or delete VLANs on a VTP client. · A VTP client only stores the VLAN information for the entire domain while the switch is on. · A switch reset deletes the VLAN information. · You must configure VTP client mode on a switch. QUESTION 14 Which function does IP SLA ICMP ECHO operation perform to assist with troubleshooting A. B. C. D. one way jitter measurement congestion detection hop-by-hop response time packet-loss detection Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 15 Which mode are in PAgP? (choose two) A. B. C. D. E. Auto Desirable Active Passive On Correct Answer: AB Section: (none) Explanation Explanation/Reference: http://www.omnisecu.com/cisco-certified-network-associate-ccna/etherchannel-pagp-and-lacp-modes.php QUESTION 16 What routing protocol use first-hand information from peers? A. B. C. D. link state distance-vector path-vector other Correct Answer: A Section: (none) Explanation Explanation/Reference: http://www.ciscopress.com/articles/article.asp?p=24090&seqNum=4 QUESTION 17 In an Ethernet network, under what two scenarios can devices transmit? (Choose two.) A. B. C. D. E. when they receive a special token when there is a carrier when they detect no other devices are sending when the server grants access when the medium is idle Correct Answer: CE Section: (none) Explanation Explanation/Reference: QUESTION 18 Which two protocols are used by bridges and/or switches to prevent loops in a layer 2 network? (Choose two.) A. B. C. D. E. 802.1d VTP 802.1q SAP STP Correct Answer: AE Section: (none) Explanation Explanation/Reference: QUESTION 19 At which layer of the OSI model does PPP perform? A. B. C. D. E. Layer 2 Layer 3 Layer 4 Layer 5 Layer 1 Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 20 What are three reasons that an organization with multiple branch offices and roaming users might implement a Cisco VPN solution instead of point-to-point WAN links? (Choose three.) A. B. C. D. E. F. reduced cost better throughput broadband incompatibility increased security scalability reduced latency Correct Answer: ADE Section: (none) Explanation Explanation/Reference: QUESTION 21 Which two statements about IPv4 multicast traffic are true? (Choose two.) A. B. C. D. E. It burdens the source host without affecting remote hosts. It uses a minimum amount of network bandwidth. It is bandwidth-intensive. It simultaneously delivers multiple streams of data. It is the most efficient way to deliver data to multiple receivers. Correct Answer: DE Section: (none) Explanation Explanation/Reference: QUESTION 22 Which IPv6 header field is equivalent to the TTL? A. B. C. D. E. Scan Timer TTD Flow Label Hop Limit Hop Count Correct Answer: D Section: (none) Explanation Explanation/Reference: Time To Live (TTL)/Hop Limit (8 bits) http://ipv6.com/articles/general/IPv6-Header.htm QUESTION 23 which port security mode can assist with troubleshooting by keeping count of violations? A. B. C. D. access protect restrict shutdown Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 24 which 2 optns are requirements for configuring ripv2 for ipv4 (choose 2) A. B. C. D. E. enabling RIP authentication connecting RIP to a WAN Interface enabling auto route sumamrization allowing unicast updates for RIP enabling RIP on the router Correct Answer: DE Section: (none) Explanation Explanation/Reference: QUESTION 25 which configuration command can u apply to a hsrp router so that its local interface becomes A. B. C. D. E. active if all other routers in the group fail? no additional config is required standby 1 track ethernet standby 1 preempt standby 1 priority 250 Correct Answer: D Section: (none) Explanation Explanation/Reference: QUESTION 26 which 2 statements about extended traceroute command is true A. B. C. D. E. it can use a specified TTL value it can send packets from specified interface or ip add it can validate the reply data it can use a specificed TOS it can repeated automatically to a specified interval Correct Answer: B Section: (none) Explanation Explanation/Reference: QUESTION 27 which statement about EIGRP on IPv6 device is true A. B. C. D. E. It is configured on the interface It is globally configured If is configured using a network statement It is vendor agnostic. It supports a shutdown feature. Correct Answer: AE Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/support/docs/ip/enhanced-interior-gateway-routing-protocol-eigrp/113267eigrp-ipv6-00.html QUESTION 28 which command can you enter to troubleshoot the failure of address assignment ? A. B. C. D. sh ip dhcp database sh ip dhcp pool sh ip dhcp import sh ip dhcp server statistics Correct Answer: B Section: (none) Explanation Explanation/Reference: QUESTION 29 which three technical services support cloud computing ? A. B. C. D. E. F. network-monitored power sources layer 3 network routing ip localization redundant connections VPN connectivity extended SAN services Correct Answer: DEF Section: (none) Explanation Explanation/Reference: QUESTION 30 which two steps must you perform to enbale router-on-stick on a switch ? A. B. C. D. E. connect the router to a trunk port config the subint number exactly the same as the matching VLAN config full duplex cofigure an ip route to the vlan destn net assign the access port to the vlan Correct Answer: AB Section: (none) Explanation Explanation/Reference: QUESTION 31 which add prefix does OSPFv3 use when multiple IPv6 address are configured on a single interface ? A. B. C. D. all prefix on the int the prefix that the administrator configure for OSPFv3 use the lowest prefix on the int the highest prefix on the int Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 32 which IP configuration does the CIDR notation 192.168.1.1/25 refer? A. B. C. D. E. 192.168.1.1 255.255.255.64 192.168.1.1 255.255.255.1 192.168.1.1 255.255.255.32 192.168.1.1 255.255.255.256 192.168.1.1 255.255.255.128 Correct Answer: E Section: (none) Explanation Explanation/Reference: QUESTION 33 CIDR notation (255.255.255.252 ) / notation A. B. C. D. 30 31 32 33 Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 34 Which two of these statements regarding RSTP are correct? (Choose two) A. B. C. D. E. RSTP cannot operate with PVST+. RSTP defines new port roles. RSTP defines no new port states. RSTP is a proprietary implementation of IEEE 802.1D STP. RSTP is compatible with the original IEEE 802.1D STP Correct Answer: BE Section: (none) Explanation Explanation/Reference: QUESTION 35 What is known as ―one-to-nearest addressing in IPv6? A. B. C. D. global unicast anycast multicast unspecified address Correct Answer: B Section: (none) Explanation Explanation/Reference: QUESTION 36 When a device learns multiple routes to a specific network, it installs the route with: A. Longest bit Match (highest subnet Mask) B. lowest AD C. lowest metric D. equal load balancing Correct Answer: B Section: (none) Explanation Explanation/Reference: http://www.ciscopress.com/articles/article.asp?p=2180208&seqNum=9 QUESTION 37 Requirement to configure DHCP binding ( 2 options) A. B. C. D. DHCP pool ip address Hardware address other option Correct Answer: BC Section: (none) Explanation Explanation/Reference: QUESTION 38 how to see dhcp conflict? A. show ip dhcp pool B. show dhcp database C. D. Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 39 Which Cisco platform can verify ACLs? A. B. C. D. Cisco Prime Infrastructure Cisco Wireless LAN Controller Cisco APIC-EM Cisco IOS-XE Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 40 Which type of mac address learning age out? A. Dynamic B. Static C. Auto D. one more option Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 41 syslog question (choose two) A. B. C. D. E. stored on internal devise stored on external device log file size depends on the memory size can be erased on reboot disable by default Correct Answer: BE Section: (none) Explanation Explanation/Reference: QUESTION 42 Which major component of the network virtualization architecture isolate users according to policy? A. B. C. D. policy enforcement network access control network services virtualization can’t remember Correct Answer: B Section: (none) Explanation Explanation/Reference: Network access control and segmentation of classes of users: Users are authenticated and either allowed or denied into a logical partition. Users are segmented into employees, contractors and consultants, and guests, with respective access to IT assets. This component identifies users who are authorized toaccess the network and then places them into the appropriate logical partition. QUESTION 43 Which two statements about firewalls are true ? A. B. C. D. E. They can be used with an intrusion prevention system. They can limit unauthorized user access to protect data. Each wireless access point requires its own firewall They must be placed only at locations where the private network connects to the internet. They can prevent attacks from the internet only. Correct Answer: AB Section: (none) Explanation Explanation/Reference: QUESTION 44 Which two statements about data VLANs on access ports are true ? ( Choose two) A. B. C. D. E. They can be configured as trunk ports Two or more VLANs can be configured on the interface 802.1Q encapsulation must be configured on the interface Exactly one VLAN can be configured on the interface. They can be configured as host ports. Correct Answer: DE Section: (none) Explanation Explanation/Reference: QUESTION 45 Where does the configuration reside when a helper address is configured to support DHCP ? A. B. C. D. on the switch trunk interface. on the router closest to the client. on the router closest to the server. on every router along the path. Correct Answer: B Section: (none) Explanation Explanation/Reference: QUESTION 46 Which command can you enter to configure an IPV6 floating static route? A. B. C. D. Router(config)# ipv6 route static resolve default Router(config)# ipv6 route::/0 serail0/1 Router(config)# ipv6 route FE80:0202::/32 serail 0/1 201 Router(config)# ipv6 route FE80:0202::/32 serail 0/1 1 Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 47 How does NAT overloading provide one-to-many address translation? A. It uses a pool of addresses B. It converts IPV4 addresses to unused IPv6 Addresses C. It assigns a unique TCP/UDP port to each session D. It uses virtual MAC Address and Virtual IP Addresses Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 48 Which three options are types of Layer 2 network attack ? (Choose three) A. B. C. D. E. F. Spoofing attacks Vlan Hopping botnet attacks DDOS attacks ARP Attacks Brute force attacks Correct Answer: ABE Section: (none) Explanation Explanation/Reference: QUESTION 49 Which three commands can you use to set a router boot image? (Choose three.) A. B. C. D. E. F. Router(config)# boot system flash c4500-p-mz.121-20.bin Router(config)# boot system tftp c7300-js-mz.122-33.SB8a.bin Router(config)#boot system rom c7301-advipservicesk9-mz.124-24.T4.bin Router> boot flash:c180x-adventerprisek9-mz-124-6T.bin Router(config)#boot flash:c180x-adventerprisek9-mz-124-6T.bin Router(config)#boot bootldr bootflash:c4500-jk9s-mz.122-23f.bin Correct Answer: ABC Section: (none) Explanation Explanation/Reference: QUESTION 50 Which command would you configure globally on a Cisco router that to re-enable CDP if it was disabled by the administrator? directly connected Cisco devices? A. B. C. D. enable cdp cdp enable cdp run run cdp Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 51 What are three characteristics of the TCP protocol? (Choose three.) A. B. C. D. E. F. It uses a single SYN-ACK message to establish a connection. The connection is established before data is transmitted. It ensures that all data is transmitted and received by the remote device. It supports significantly higher transmission speeds than UDP. It requires applications to determine when data packets must be retransmitted. It uses separate SYN and ACK messages to establish a connection. Correct Answer: BCF Section: (none) Explanation Explanation/Reference: QUESTION 52 What is the authoritative source for an address lookup? A. B. C. D. a recursive DNS search the operating system cache the ISP local cache the browser cache Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 53 During which phase of PPPoE is PPP authentication performed? A. B. C. D. E. the PPP Session phase Phase 2 the Active Discovery phase the Authentication phase Phase 1 Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 54 Which three circumstances can cause a GRE tunnel to be in an up/down state? (Choose three.) A. The tunnel interface IP address is misconfigured. B. The tunnel interface is down. C. A valid route to the destination address is missing from the routing table. D. The tunnel address is routed through the tunnel itself. E. The ISP is blocking the traffic. F. An ACL is blocking the outbound traffic. Correct Answer: BCD Section: (none) Explanation Explanation/Reference: QUESTION 55 Which two statements about northbound and southbound APIs are true? (Choose two.) A. B. C. D. E. F. Only southbound APIs allow program control of the network. Only northbound APIs allow program control of the network. Only southbound API interfaces use a Service Abstraction Layer. Only northbound API interfaces use a Service Abstraction Layer. Both northbound and southbound API interfaces use a Service Abstraction Layer. Both northbound and southbound APIs allow program control of the network. Correct Answer: BC Section: (none) Explanation Explanation/Reference: QUESTION 56 Refer to the exhibit. Switch-1 needs to send data to a host with a MAC address of 00b0.d056.efa4. What will Switch-1 do with this data? A. Switch-1 will drop the data because it does not have an entry for that MAC address. B. Switch-1 will flood the data out all of its ports except the port from which the data originated. C. Switch-1 will send an ARP request out all its ports except the port from which the data originated. D. Switch-1 will forward the data to its default gateway. Correct Answer: B Section: (none) Explanation Explanation/Reference: QUESTION 57 How many broadcast domains are shown in the graphic assuming only the default VLAN is confgured on the switches? A. B. C. D. one two six twelve Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 58 What are two reasons that duplex mismatches can be difficult to diagnose? (Choose two.) A. B. C. D. E. The interface displays a connected (up/up) state even when the duplex settings are mismatched. The symptoms of a duplex mismatch may be intermittent. Auto-negotiation is disabled. Full-duplex interfaces use CSMA/CD logic, so mismatches may be disguised by collisions. 1-Gbps interfaces are full-duplex by default. Correct Answer: AB Section: (none) Explanation Explanation/Reference: QUESTION 59 Which interface counter can you use to diagnose a duplex mismatch problem? A. no earner B. late collisions C. D. E. F. giants CRC errors deferred runts Correct Answer: B Section: (none) Explanation Explanation/Reference: QUESTION 60 Afar you apply the given configuration to R1, you notice that it failed to enable OSPF Which action can you take to correct the problem? A. B. C. D. Configure a loopback interface on R1 Enable IPv6 unicast routing on R1. Configure an IPv4 address on interface FO/0. Configure an autonomous system number on OSPF. Correct Answer: B Section: (none) Explanation Explanation/Reference: QUESTION 61 What does split-horizon do? A. B. C. D. Prevent routing loop in distance vector protocol Prevent switching loop in distance vector protocol Prevent switching loop in link-state protocol Prevent routing loop in link-state protocol Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 62 A. B. C. D. E. The MAC address table will now have an additional entry of fa0/1 FFFF.FFFF.FFFF. Only host A will be allowed to transmit frames on fa0/1. This frame will be discarded when it is received by 2950Switch. All frames arriving on 2950Switch with a destination of 0000.00aa.aaaa will be forwarded out fa0/1 Hosts B and C may forward frames out fa0/1 but frames arriving from other switches will not be forwarded out fa0/1. F. Only frames from source 0000.00bb.bbbb, the first learned MAC address of 2950Switch, will be forwarded out fa0/1. Correct Answer: BD Section: (none) Explanation Explanation/Reference: QUESTION 63 Which three statements correcctly describe Network Device A? (Choose three.) A. With a network wide mask of 255.255.255.128, each interface does not require an IP address. B. With a network wide mask of 255.255.255.128, each interface does require an IP address on a unique IP subnet. C. With a network wide mask of 255.255.255.0, must be a Layer 2 device for the PCs to communicate with each other. D. With a network wide mask of 255.255.255.0, must be a Layer 3 device for the PCs to communicate with each other. E. With a network wide mask of 255.255.255.0, each interface does not require an IP address. Correct Answer: BDE Section: (none) Explanation Explanation/Reference: QUESTION 64 Refer to the exhibit At the end of an RSTP election process, which access layer switch port will assume the discarding role? A. B. C. D. E. F. Switch3, port fa0/1 Switch3, port fa0/12 Switch4, port fa0/11 Switch4, port fa0/2 Switch3, port Gi0/1 Switch3, port Gi0/2 Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 65 Refer to the exhibit Why is flash memory erased prior to upgrading the IOS image from the TFTP server? A. B. C. D. The router cannot verify that the Cisco IOS image currently in flash is valid. Flash memory on Cisco routers can contain only a single IOS image. Erasing current flash content is requested during the copy dialog. In order for the router to use the new image as the default, it must be the only IOS image in flash. Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 66 The network shown in the diagram is experiencing connectivity problems. Which of the following will correct the problems? (Choose two.) A. B. C. D. E. F. Configure the gateway on Host A as 10.1.1.1. Configure the gateway on Host B as 10.1.2.254. Configure the IP address of Host A as 10.1.2.2. Configure the IP address of Host B as 10.1.2.2. Configure the masks on both hosts to be 255.255.255.224. Configure the masks on both hosts to be 255.255.255.240. Correct Answer: BD Section: (none) Explanation Explanation/Reference: 200-125 114q Number: 200-125 Passing Score: 810 Time Limit: 120 min File Version: 1.0 Edited by Overlord Thanks to KINGSMAN ManhDT Liam coolguy01 NET-37 Exam A QUESTION 1 Which three statements about HSRP operation are true? (Choose three.) A. B. C. D. The virtual IP address and virtual MAC address are active on the HSRP Master router. The HSRP default timers are a 3 second hello interval and a 10 second dead interval. HSRP supports only clear-text authentication The HSRP virtual IP address must be on a different subnet than the routers’ interfaces on the same LAN. E. The HSRP virtual IP address must be the same as one of the router’s interface addresses on the LAN. F. HSRP supports up to 255 groups per interface, enabling an administrative form of load balancing. Correct Answer: ABF Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/support/docs/ip/hot-standby-router-protocol-hsrp/10583-62.html#topic5 “The active router sources hello packets from its configured IP address and the HSRP virtual MAC address. The standby router sources hellos from its configured IP address and the burned-in MAC address (BIA).” http://www.cisco.com/c/en/us/support/docs/ip/hot-standby-router-protocol-hsrp/10583-62.html#topic14 “By default, these timers are set to 3 and 10 seconds, respectively…” http://www.cisco.com/c/en/us/support/docs/switches/catalyst-6000-series-switches/29545-168.html#q1 Load Sharing with HSRP http://www.cisco.com/c/en/us/support/docs/ip/hot-standby-router-protocol-hsrp/13781-7.html#conf “…has a 256 unique HSRP group ID limit.” “…the allowed group ID range (0-255). … MSFC2A (Supervisor Engine 32) can use any number of group IDs from that range.” QUESTION 2 Which two options describe benefits of aggregated chassis technology ( choose 2) A. B. C. D. E. F. it reduces management overhead switches can be located anywhere regardless of there physical location it requires only one IP add per VLAN it requires only three IP add per VLAN it supports HSRP VRRP GLBP it support redundant configuration files Correct Answer: AC Section: (none) Explanation Explanation/Reference: QUESTION 3 When troubleshooting client DNS issues, which two task must you perform? (Choose two) A. B. C. D. E. Ping a public website IP address. Ping the DNS Server. Determine whether a DHCP address has been assigned. Determine whether the hardware address is correct. Determine whether the name servers have been configured Correct Answer: BC Section: (none) Explanation Explanation/Reference: https://l.facebook.com/l.php?u=http%3A%2F%2Fwww.cisco.com%2Fen%2FUS%2Fdocs% 2Finternetworking%2Ftroubleshooting%2Fguide%2Ftr1907.html% 23wp1021264&h=ATMT6hWMWKar6G3cbMd8vYoG64obKG4CIuxXlmCWtCLencP9vUG0hrC3C0azv18a RsmIsdrKko8ew_O6UkUwYCVqgYvxTz3TFquXNKyrnrAa1arE1V4HBFjg4_E2gJSawoz2_g Ping the destination by name perform a DNS lookup on the destination QUESTION 4 Which utility can you use to identify redundant or shadow rules ? A. B. C. D. The ACL trace tool in Cisco APIC-EM. The ACL analysis tool in Cisco APIC-EM. The Cisco APIC-EM automation scheduler. The Cisco IWAN application. Correct Answer: B Section: (none) Explanation Explanation/Reference: QUESTION 5 Which 2 statements about extended traceroute command is true? A. B. C. D. E. it can send packets from specified interface or ip add it can use a specified TTL value it can validate the reply data it can use a specificed TOS it can repeated automatically to a specified interval Correct Answer: AB Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/support/docs/ip/routing-information-protocol-rip/13730-ext-pingtrace.html#ext_troute “This table lists the traceroute command field descriptions: Source address: The interface or IP address of the router to use as a source address for the probes. The router normally picks the IP address of the outbound interface to use. Minimum Time to Live [1]: The TTL value for the first probes. The default is 1, but it can be set to a higher value to suppress the display of known hops. Maximum Time to Live [30]: The largest TTL value that can be used. The default is 30. The traceroute command terminates when the destination is reached or when this value is reached.” QUESTION 6 A BPDU guard is configured on an interface that has PortFast Enable. Which state does the interface enter when it recives a BPDU ? A. Blocking B. Shutdown. C. Listening. D. Errdisable. Correct Answer: D Section: (none) Explanation Explanation/Reference: QUESTION 7 Which command can you enter to determine the addresses that have been assigned on a DHCP Server? A. B. C. D. Show ip DHCP database Show ip DHCP pool Show ip DHCP binding Show ip DHCP server statistic Correct Answer: C Section: (none) Explanation Explanation/Reference: http://www.aubrett.com/InformationTechnology/RoutingandSwitching/Cisco/CiscoRouters/ DHCPBindings.aspx “Router#show ip dhcp binding Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type 10.16.173.0 24d9.2141.0ddd Jan 12 2013 03:42 AM Automatic” QUESTION 8 Which statement about SNMPv2 is true ? A. B. C. D. Its privacy algorithms use MD5 encryption by default. it requires passwords to be encrypyed. Its authetication and privacy algorithms are enable without default values. It requires passwords at least eight characters en length. Correct Answer: C Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/td/docs/ios/12_2/configfun/configuration/guide/ffun_c/ fcf014.html#wp1010901 “Model___Level_________Authentication_____Encryption__What Happens v2c_____noAuthNoPriv___Community String__No________Uses a community string match for authentication.” So B & D must be wrong, because there is no “password” in SNMPv2. A is wrong because there is no encryption in SNMPv2. QUESTION 9 which type of IP address of ipv6 that also exist in IPv4 but barely used? A. B. C. D. unicast multicast anycast broadcast Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 10 Which symptom most commonly indicates that 2 connecting interface are configured with a duplex mismatch? A. B. C. D. an int with up/down state an int with down/down state late collisions on the interface the spanning tree process shutting down Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 11 How Eigrp for ipv6 configuration done? ( choose 2) A. B. C. D. E. uses process number neighbor configured directly configured driectly on interface configured globally interface have shutdown feature Correct Answer: CE Section: (none) Explanation Explanation/Reference: QUESTION 12 Which VTP mode can not make a change to vlan? A. B. C. D. Server Client Transparent Off Correct Answer: B Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/support/docs/lan-switching/vtp/10558-21.html#vtp_modes “Client—VTP clients behave the same way as VTP servers, but you cannot create, change, or delete VLANs on a VTP client. Transparent—VTP transparent switches do not participate in VTP.” QUESTION 13 Which function does IP SLA ICMP ECHO operation perform to assist with troubleshooting A. B. C. D. one way jitter measurement congestion detection hop-by-hop response time packet-loss detection Correct Answer: C Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipsla/configuration/15-mt/sla-15-mt-book/ sla_icmp_pathjitter.html QUESTION 14 Which two EtherChannel PAgP modes can you configure? (choose two) A. B. C. D. E. Auto Desirable Active Passive On Correct Answer: AB Section: (none) Explanation Explanation/Reference: http://www.omnisecu.com/cisco-certified-network-associate-ccna/etherchannel-pagp-and-lacp-modes.php QUESTION 15 What routing protocol use first-hand information from peers? A. B. C. D. link state distance-vector path-vector other Correct Answer: A Section: (none) Explanation Explanation/Reference: http://www.ciscopress.com/articles/article.asp?p=24090&seqNum=4 QUESTION 16 In an Ethernet network, under what two scenarios can devices transmit? (Choose two.) A. B. C. D. E. when they receive a special token when there is a carrier when they detect no other devices are sending when the server grants access when the medium is idle Correct Answer: CE Section: (none) Explanation Explanation/Reference: QUESTION 17 Which two protocols are used by bridges and/or switches to prevent loops in a layer 2 network? (Choose two.) A. B. C. D. E. 802.1d VTP 802.1q SAP STP Correct Answer: AE Section: (none) Explanation Explanation/Reference: QUESTION 18 At which layer of the OSI model does PPP perform? A. B. C. D. E. Layer 2 Layer 3 Layer 4 Layer 5 Layer 1 Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 19 What are three reasons that an organization with multiple branch offices and roaming users might implement a Cisco VPN solution instead of point-to-point WAN links? (Choose three.) A. B. C. D. E. F. reduced cost better throughput broadband incompatibility increased security scalability reduced latency Correct Answer: ADE Section: (none) Explanation Explanation/Reference: QUESTION 20 Which two statements about IPv4 multicast traffic are true? (Choose two.) A. B. C. D. E. It burdens the source host without affecting remote hosts. It uses a minimum amount of network bandwidth. It is bandwidth-intensive. It simultaneously delivers multiple streams of data. It is the most efficient way to deliver data to multiple receivers. Correct Answer: BE Section: (none) Explanation Explanation/Reference: IP multicast is a bandwidth-conserving technology that reduces traffic by simultaneously delivering a single stream of information to potentially thousands of corporate recipients and homes. http://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/mcst_ovr.html QUESTION 21 Which IPv6 header field is equivalent to the TTL? A. B. C. D. E. Scan Timer TTD Flow Label Hop Limit Hop Count Correct Answer: D Section: (none) Explanation Explanation/Reference: Time To Live (TTL)/Hop Limit (8 bits) http://ipv6.com/articles/general/IPv6-Header.htm QUESTION 22 which port security mode can assist with troubleshooting by keeping count of violations? A. B. C. D. access protect restrict shutdown Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 23 which 2 options are requirements for configuring ripv2 for ipv4 (choose 2) A. enabling RIP authentication B. connecting RIP to a WAN Interface C. enabling auto route sumamrization D. allowing unicast updates for RIP E. enabling RIP on the router Correct Answer: DE Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/td/docs/ios/12_2/ip/configuration/guide/fipr_c/1cfrip.html#wp1000889 “Enabling RIP (Required) Allowing Unicast Updates for RIP (Required)” RIP Version 1 and Version 2 have the same basic requirements! QUESTION 24 which statement about EIGRP on IPv6 device is true A. B. C. D. E. It is configured on the interface It is globally configured If is configured using a network statement It is vendor agnostic. It supports a shutdown feature. Correct Answer: AE Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/support/docs/ip/enhanced-interior-gateway-routing-protocol-eigrp/113267eigrp-ipv6-00.html QUESTION 25 which command can you enter to troubleshoot the failure of address assignment ? A. B. C. D. sh ip dhcp database sh ip dhcp pool sh ip dhcp import sh ip dhcp server statistics Correct Answer: B Section: (none) Explanation Explanation/Reference: QUESTION 26 which three technical services support cloud computing ? A. B. C. D. E. F. network-monitored power sources layer 3 network routing ip localization redundant connections VPN connectivity extended SAN services Correct Answer: DEF Section: (none) Explanation Explanation/Reference: QUESTION 27 which add prefix does OSPFv3 use when multiple IPv6 address are configured on a single interface ? A. B. C. D. All prefixes on the interface The prefix that the administrator configure for OSPFv3 use The lowest prefix on the int The highest prefix on the int Correct Answer: A Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_ospf/configuration/15-sy/iro-15-sy-book/ip6-routeospfv3.html#GUID-05F3F09C-FE3E-41D6-9845-111FB17AD030 “In IPv6, you can configure many address prefixes on an interface. In OSPFv3, all address prefixes on an interface are included by default. You cannot select some address prefixes to be imported into OSPFv3; either all address prefixes on an interface are imported, or no address prefixes on an interface are imported.” QUESTION 28 which IP configuration does the CIDR notation 192.168.1.1/25 refer? A. B. C. D. E. 192.168.1.1 255.255.255.64 192.168.1.1 255.255.255.1 192.168.1.1 255.255.255.32 192.168.1.1 255.255.255.256 192.168.1.1 255.255.255.128 Correct Answer: E Section: (none) Explanation Explanation/Reference: QUESTION 29 CIDR notation (255.255.255.252 ) / notation A. B. C. D. 30 31 32 33 Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 30 Which two of these statements regarding RSTP are correct? (Choose two) A. B. C. D. E. RSTP cannot operate with PVST+. RSTP defines new port roles. RSTP defines no new port states. RSTP is a proprietary implementation of IEEE 802.1D STP. RSTP is compatible with the original IEEE 802.1D STP Correct Answer: BE Section: (none) Explanation Explanation/Reference: QUESTION 31 What is known as ―one-to-nearest addressing in IPv6? A. B. C. D. global unicast anycast multicast unspecified address Correct Answer: B Section: (none) Explanation Explanation/Reference: QUESTION 32 When a device learns multiple routes to a specific network, it installs the route with: A. B. C. D. Longest bit Match (highest subnet Mask) lowest AD lowest metric equal load balancing Correct Answer: B Section: (none) Explanation Explanation/Reference: http://www.ciscopress.com/articles/article.asp?p=2180208&seqNum=9 QUESTION 33 Which Cisco platform can verify ACLs? A. B. C. D. Cisco Prime Infrastructure Cisco Wireless LAN Controller Cisco APIC-EM Cisco IOS-XE Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 34 Which type of mac address learning age out? A. B. C. D. Dynamic Static Auto one more option Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 35 Which two statements about syslog logging are true? (choose two) A. B. C. D. E. Syslog logging is disabled by default Messages are stored in the internal memory of the device The size of the log file is dependent on the resources of the device Messages are stored external to the device Messages can be erased when the device reboots. Correct Answer: AD Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2960/software/release/12-2_55_se/ configuration/guide/scg_2960/swlog.html “By default, a switch sends the output from system messages and debug privileged EXEC commands to a _logging process_.” “The _logging process_ controls the distribution of logging messages to various destinations, such as the logging buffer, terminal lines, or a UNIX _syslog_ server, depending on your configuration. The process also sends messages to the console.” Reading through parts of the reference should make it clear, that “syslog logging” is not the same as “System Message Logging”. “System Message Logging” is enabled by default and sends messages to the so called “logging process”. This then sends it to console, a buffer, or even a syslog Server (this part is not configured by default = “syslog logging” is not enabled by default). Now the “logging synchronous” comes in, when all the messages showing up in your console get in the way of you, typing in commands, since the displaying of messages jumbles up your inputs. QUESTION 36 Which major component of the Cisco Network Virtualization Architecture isolate users according to policy? A. B. C. D. Policy Enforcement Network Access Control Network Services Virtualization Path Isolation Correct Answer: B Section: (none) Explanation Explanation/Reference: Network access control and segmentation of classes of users: Users are authenticated and either allowed or denied into a logical partition. Users are segmented into employees, contractors and consultants, and guests, with respective access to IT assets. This component identifies users who are authorized toaccess the network and then places them into the appropriate logical partition. QUESTION 37 Which two statements about firewalls are true ? A. B. C. D. E. They can be used with an intrusion prevention system. They can limit unauthorized user access to protect data. Each wireless access point requires its own firewall They must be placed only at locations where the private network connects to the internet. They can prevent attacks from the internet only. Correct Answer: AB Section: (none) Explanation Explanation/Reference: QUESTION 38 Which two statements about data VLANs on access ports are true ? ( Choose two) A. B. C. D. E. They can be configured as trunk ports Two or more VLANs can be configured on the interface 802.1Q encapsulation must be configured on the interface Exactly one VLAN can be configured on the interface. They can be configured as host ports. Correct Answer: DE Section: (none) Explanation Explanation/Reference: QUESTION 39 Where does the configuration reside when a helper address is configured to support DHCP ? A. B. C. D. on the switch trunk interface. on the router closest to the client. on the router closest to the server. on every router along the path. Correct Answer: B Section: (none) Explanation Explanation/Reference: QUESTION 40 Which command can you enter to configure an IPV6 floating static route? A. B. C. D. Router(config)# ipv6 route static resolve default Router(config)# ipv6 route::/0 serail0/1 Router(config)# ipv6 route FE80:0202::/32 serial 0/1 201 Router(config)# ipv6 route FE80:0202::/32 serial 0/1 1 Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 41 How does NAT overloading provide one-to-many address translation? A. B. C. D. It uses a pool of addresses It converts IPV4 addresses to unused IPv6 Addresses It assigns a unique TCP/UDP port to each session It uses virtual MAC Address and Virtual IP Addresses Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 42 Which three options are types of Layer 2 network attack ? (Choose three) A. B. C. D. E. F. Spoofing attacks Vlan Hopping botnet attacks DDOS attacks ARP Attacks Brute force attacks Correct Answer: ABE Section: (none) Explanation Explanation/Reference: QUESTION 43 Which three commands can you use to set a router boot image? (Choose three.) A. B. C. D. E. F. Router(config)# boot system flash c4500-p-mz.121-20.bin Router(config)# boot system tftp c7300-js-mz.122-33.SB8a.bin Router(config)#boot system rom c7301-advipservicesk9-mz.124-24.T4.bin Router> boot flash:c180x-adventerprisek9-mz-124-6T.bin Router(config)#boot flash:c180x-adventerprisek9-mz-124-6T.bin Router(config)#boot bootldr bootflash:c4500-jk9s-mz.122-23f.bin Correct Answer: ABC Section: (none) Explanation Explanation/Reference: QUESTION 44 Which command would you configure globally on a Cisco router that to re-enable CDP if it was disabled by the administrator? directly connected Cisco devices? A. B. C. D. enable cdp cdp enable cdp run run cdp Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 45 What are three characteristics of the TCP protocol? (Choose three.) A. B. C. D. E. F. It uses a single SYN-ACK message to establish a connection. The connection is established before data is transmitted. It ensures that all data is transmitted and received by the remote device. It supports significantly higher transmission speeds than UDP. It requires applications to determine when data packets must be retransmitted. It uses separate SYN and ACK messages to establish a connection. Correct Answer: BCF Section: (none) Explanation Explanation/Reference: QUESTION 46 What is the authoritative source for an address lookup? A. B. C. D. a recursive DNS search the operating system cache the ISP local cache the browser cache Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 47 During which phase of PPPoE is PPP authentication performed? A. the PPP Session phase B. Phase 2 C. the Active Discovery phase D. the Authentication phase E. Phase 1 Correct Answer: A Section: (none) Explanation Explanation/Reference: PPP Session Phase—In this phase, PPP options are negotiated and authentication is performed. http://www.cisco.com/c/en/us/td/docs/security/asa/asa92/configuration/vpn/asa-vpn-cli/vpn-pppoe.html QUESTION 48 Which three circumstances can cause a GRE tunnel to be in an up/down state? (Choose three.) A. B. C. D. E. F. The tunnel interface IP address is misconfigured. The tunnel interface is down. A valid route to the destination address is missing from the routing table. The tunnel address is routed through the tunnel itself. The ISP is blocking the traffic. An ACL is blocking the outbound traffic. Correct Answer: BCD Section: (none) Explanation Explanation/Reference: QUESTION 49 Which two statements about northbound and southbound APIs are true? (Choose two.) A. B. C. D. E. F. Only southbound APIs allow program control of the network. Only northbound APIs allow program control of the network. Only southbound API interfaces use a Service Abstraction Layer. Only northbound API interfaces use a Service Abstraction Layer. Both northbound and southbound API interfaces use a Service Abstraction Layer. Both northbound and southbound APIs allow program control of the network. Correct Answer: BC Section: (none) Explanation Explanation/Reference: QUESTION 50 Refer to the exhibit. Switch-1 needs to send data to a host with a MAC address of 00b0.d056.efa4. What will Switch-1 do with this data? A. Switch-1 will drop the data because it does not have an entry for that MAC address. B. Switch-1 will flood the data out all of its ports except the port from which the data originated. C. Switch-1 will send an ARP request out all its ports except the port from which the data originated. D. Switch-1 will forward the data to its default gateway. Correct Answer: B Section: (none) Explanation Explanation/Reference: QUESTION 51 How many broadcast domains are shown in the graphic assuming only the default VLAN is confgured on the switches? A. B. C. D. one two six twelve Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 52 What are two reasons that duplex mismatches can be difficult to diagnose? (Choose two.) A. B. C. D. E. The interface displays a connected (up/up) state even when the duplex settings are mismatched. The symptoms of a duplex mismatch may be intermittent. Auto-negotiation is disabled. Full-duplex interfaces use CSMA/CD logic, so mismatches may be disguised by collisions. 1-Gbps interfaces are full-duplex by default. Correct Answer: AB Section: (none) Explanation Explanation/Reference: QUESTION 53 Which interface counter can you use to diagnose a duplex mismatch problem? A. B. C. D. E. F. no earner late collisions giants CRC errors deferred runts Correct Answer: B Section: (none) Explanation Explanation/Reference: QUESTION 54 What does split-horizon do? A. B. C. D. Prevent routing loop in distance vector protocol Prevent switching loop in distance vector protocol Prevent switching loop in link-state protocol Prevent routing loop in link-state protocol Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 55 A. B. C. D. E. The MAC address table will now have an additional entry of fa0/1 FFFF.FFFF.FFFF. Only host A will be allowed to transmit frames on fa0/1. This frame will be discarded when it is received by 2950Switch. All frames arriving on 2950Switch with a destination of 0000.00aa.aaaa will be forwarded out fa0/1 Hosts B and C may forward frames out fa0/1 but frames arriving from other switches will not be forwarded out fa0/1. F. Only frames from source 0000.00bb.bbbb, the first learned MAC address of 2950Switch, will be forwarded out fa0/1. Correct Answer: BD Section: (none) Explanation Explanation/Reference: QUESTION 56 Which three statements correcctly describe Network Device A? (Choose three.) A. With a network wide mask of 255.255.255.128, each interface does not require an IP address. B. With a network wide mask of 255.255.255.128, each interface does require an IP address on a unique IP subnet. C. With a network wide mask of 255.255.255.0, must be a Layer 2 device for the PCs to communicate with each other. D. With a network wide mask of 255.255.255.0, must be a Layer 3 device for the PCs to communicate with each other. E. With a network wide mask of 255.255.255.0, each interface does not require an IP address. Correct Answer: BDE Section: (none) Explanation Explanation/Reference: QUESTION 57 Refer to the exhibit At the end of an RSTP election process, which access layer switch port will assume the discarding role? A. B. C. D. E. F. Switch3, port fa0/1 Switch3, port fa0/12 Switch4, port fa0/11 Switch4, port fa0/2 Switch3, port Gi0/1 Switch3, port Gi0/2 Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 58 Refer to the exhibit Why is flash memory erased prior to upgrading the IOS image from the TFTP server? A. B. C. D. The router cannot verify that the Cisco IOS image currently in flash is valid. Flash memory on Cisco routers can contain only a single IOS image. Erasing current flash content is requested during the copy dialog. In order for the router to use the new image as the default, it must be the only IOS image in flash. Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 59 The network shown in the diagram is experiencing connectivity problems. Which of the following will correct the problems? (Choose two.) A. B. C. D. E. F. Configure the gateway on Host A as 10.1.1.1. Configure the gateway on Host B as 10.1.2.254. Configure the IP address of Host A as 10.1.2.2. Configure the IP address of Host B as 10.1.2.2. Configure the masks on both hosts to be 255.255.255.224. Configure the masks on both hosts to be 255.255.255.240. Correct Answer: BD Section: (none) Explanation Explanation/Reference: QUESTION 60 Which command can you enter to determine whether a switch port is operating in trunking mode? A. B. C. D. Show interfaces Show ip interface brief Show vlan Show Interface switchport Correct Answer: D Section: (none) Explanation Explanation/Reference: QUESTION 61 Which utility can you use to identify the cause of a traffic-flow blockage between the two devices in a network? A. B. C. D. ACL path analysis tool in APIC-EM iWAN application ACL analysis tool in APIC-EM APIC-EM automation scheduler Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 62 Which IEEE mechanism is responsible for the authentication of devices when they attempt to connect to a local network? A. B. C. D. 802.1x 802.11 802.2x 802.3x Correct Answer: A Section: (none) Explanation Explanation/Reference: EEE 802.1X is an IEEE Standard for port-based Network Access Control (PNAC). It is part of the IEEE 802.1 group of networking protocols. It provides an authentication mechanism to devices wishing to attach to a LAN or WLAN. QUESTION 63 When a router is unable to find a known route in the routing table, how does it handle the packet? A. B. C. D. It discards the packet It sends the packet over the route with the best metric It sends the packet to the next hop address It sends the packet to the gateway of last resort Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 64 Which statement about Cisco Discovery Protocol is true? A. B. C. D. It is Cisco-proprietary Protocol It can discover information from routers, firewalls and switches It runs on the network layer It runs on the physical layer and the data link layer. Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 65 Which of the three options are switchbox configurations that can always avoid duplex mismatch errors between two switches? (choose three) A. B. C. D. E. F. Set one side of the connection to the full duplex and the other side to half duplex Set both sides of the connection to full duplex Set one side of the connection to auto-negotiate and the other side to half duplex Set one side of the connection to auto-negotiate and the other side to full duplex Set both sides of the connection to auto-negotiate Set both sides of the connection to half duplex Correct Answer: BEF Section: (none) Explanation Explanation/Reference: QUESTION 66 If router R1 knows a static route to a destination network and then learns about the same destination network through a dynamic routing protocol, how does R1 respond? A. B. C. D. It refuses to advertise the dynamic route to other neighbors It sends a withdrawal signal to the neighboring router It disables the routing protocol It prefers the static route Correct Answer: D Section: (none) Explanation Explanation/Reference: By default the administrative distance of a static route is 1, meaning it will be preferred over all dynamic routing protocols. If you want to have the dynamic routing protocol used and have the static route be used only as a backup, you need to increase the AD of the static route so that it is higher than the dynamic routing protocol. QUESTION 67 Which DTP switch port mode allows the port to create a trunk link If the neighboring port is in trunk mode, or desirable auto mode? A. B. C. D. Dynamic auto Trunk Dynamic desirable Access Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 68 Which two statements about floating static routes are true? (Choose two) A. B. C. D. E. They are routes to the exact /32 destination address They are used when a route to the destination network is missing They have a higher administrative distance than the default static route administrative distance They are used as back-up routes when the primary route goes down They are dynamic routes that are learned from a server Correct Answer: CD Section: (none) Explanation Explanation/Reference: QUESTION 69 Which command can you enter to configure the switch as an authoritative NTP server with a site id: 13999902? A. B. C. D. Switch(config)#ntp master 3 Switch(config)#ntp peer 193.168.2.2 Switch(config)#ntp server 193.168.2.2 Switch(config)#ntp source 193.168.2.2 Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 70 When you enable PortFast on a switch port, the port immediately transitions to which state? A. B. C. D. Blocking Forwarding Learning Listening Correct Answer: B Section: (none) Explanation Explanation/Reference: PortFast causes a switch or trunk port to enter the spanning tree forwarding state immediately, bypassing the listening and learning states. You can use PortFast on switch or trunk ports that are connected to a single workstation, switch, or server to allow those devices to connect to the network immediately, instead of waiting for the port to transition from the listening and learning states to the forwarding state. QUESTION 71 Which two steps must you perform to enable router-on- a-stick on a switch?(choose two) A. B. C. D. E. Assign the Access port to VLAN Connect the router to a trunk port Configure the subinterface number exactly the same as matching VLAN Configure an IP route to the VLAN destination network Configure full duplex Correct Answer: AB Section: (none) Explanation Explanation/Reference: QUESTION 72 Which port security mode can assist with troubleshooting by keeping count of violations? A. B. C. D. Restrict Shutdown Access Protect Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 73 Which symptom most commonly indicates that two connecting interfaces are configured with a duplex mismatch? A. Collisions on the interface B. The spanning tree process shutting down C. An interface with up/down status D. An interface with down/down status Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 74 Which command can you enter to verify that a BGP connection to a remote device is established? A. B. C. D. Show ip community list Show ip bgp summary Show ip bgp paths Show ip route Correct Answer: B Section: (none) Explanation Explanation/Reference: Show ip bgp summary displays the status of all Border Gateway Protocol (BGP) connections QUESTION 75 In which byte of an IP packet can traffic be marked? A. B. C. D. The CoS byte The ToS byte The DSCP byte The Qos byte Correct Answer: C Section: (none) Explanation Explanation/Reference: https://en.wikipedia.org/wiki/Quality_of_service https://en.wikipedia.org/wiki/Differentiated_services Differentiated services ("DiffServ") implements the prioritized model. DiffServ marks packets according to the type of service they desire. In response to these markings, routers and switches use various queueing strategies to tailor performance to expectations. Differentiated services code point (DSCP) markings use the first 6 bits in the ToS field (now renamed as the DS Byte) of the IP(v4) packet header. QUESTION 76 What type of MAC address is aged automatically by the switch? A. B. C. D. Dynamic Manual Automatic Static Correct Answer: A Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/configuration/guide/cli/ CLIConfigurationGuide/MACAddress.html QUESTION 77 What are the two minimum required components of a DHCP binding? (choose two) A. B. C. D. E. An exclusion list A hardware address An IP address A DHCP pool An ip-helper statement Correct Answer: BC Section: (none) Explanation Explanation/Reference: An address binding is the mapping between the client’s IP and hardware addresses. http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipaddr_dhcp/configuration/15-mt/dhcp-15-mt-book/dhcpoverview.html QUESTION 78 Refer to the exhibit. If R1 receives a packet destined to 172.16.1.1, to which IP address does it send the packet? A. B. C. D. 192.168.14.4 192.168.12.2 192.168.13.3 192.168.15.5 Correct Answer: A Section: (none) Explanation Explanation/Reference: It can't find the address 172.16.1.1 so it will be directed to the Gate of last resort 192.168.14.4 QUESTION 79 What is the danger of the permit any entry in a NAT access list? A. B. C. D. It can lead to overloaded resources on the router. It can cause too many addresses to be assigned to the same interface. It can disable the overload command. It prevents the correct translation of IP addresses on the inside network. Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 80 How does a DHCP server dynamically assign IP addresses to hosts? A. Addresses are permanently assigned so that the host uses the same address at all times. B. Addresses are assigned for a fixed period of time. C. Addresses are leased to hosts. A host will usually keep the same address by periodically contacting the DHCP server to renew the lease. D. Addresses are allocated after a negotiation between the server and the host to determine the length of the agreement Correct Answer: C Section: (none) Explanation Explanation/Reference: The DHCP lifecycle consists of the following: Release: The client may decide at any time that it no longer wishes to use the IP address it was assigned, and may terminate the lease, releasing the IP address. QUESTION 81 Which component of the Cisco SDN solution serves as the centralized management system? A. B. C. D. Cisco OpenDaylight Cisco ACI Cisco APIC Cisco IWAN Correct Answer: B Section: (none) Explanation Explanation/Reference: Cisco ACI is a comprehensive SDN architecture. This policy-based automation solution supports a business-relevant application policy language, greater scalability through a distributed enforcement system, and greater network visibility. These benefits are achieved through the integration of physical and virtual environments under one policy model for networks, servers, storage, services, and security. QUESTION 82 Q19 What two results would occur if the hub were to be replaced with a switch that is configured with one Ethernet VLAN? (Choose two.) A. The number of collision domains would remain the same. B. The number of collision domains would decrease. C. D. E. F. The number of collision domains would increase. The number of broadcast domains would remain the same. The number of broadcast domains would decrease. The number of broadcast domains would increase. Correct Answer: CD Section: (none) Explanation Explanation/Reference: QUESTION 83 which configuration command can u apply to a hsrp router so that its local interface becomes active if all other routers in the group fail? A. B. C. D. no additional config is required standby 1 track ethernet standby 1 preempt standby 1 priority 250 Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 84 Which statement about SNMPv2 is true? A. B. C. D. Its privacy algorithms uses MD5 encryption by default. It requires password to be encrypted. Its authentication and privacy algorithms are enable without default values. It requires passwords at least eight characters in length. Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 85 Refer to the exhibit, you determine that Computer A cannot ping Computer Which reason for the problem is most likely true? A. B. C. D. The Subnet mask for Computer A is incorrect The default gateway address for Computer A is incorrect The subnet mask for computer B is incorrect. The default gateway address for computer B is incorrect Correct Answer: A Section: (none) Explanation Explanation/Reference: /27 = 255.255.255.224 QUESTION 86 A BPDU guard is configured on an interface that has PortFast Enable. Which state does the interface enter when it receives a BPDU? A. B. C. D. Blocking. Shutdown. Listening. Errdisable. Correct Answer: D Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/support/docs/lan-switching/spanning-tree-protocol/69980-errdisablerecovery.html#anc8 QUESTION 87 Which command can you enter to troubleshoot the failure of address assignment? A. B. C. D. Show ip DHCP database Show ip DHCP pool Show ip DHCP import Show ip DHCP server statistic Correct Answer: B Section: (none) Explanation Explanation/Reference: QUESTION 88 Which effect of the passive-interface command on R1 is true? A. B. C. D. It prevents interface Fa0/0 from sending updates. Interface Fa 0/0 operates in RIPv1 mode. It removes the 172.16.0.0 network from all updates on all interfaces on R1. It removes the 172.16.0.0 network from all updates on all interfaces on R1. Correct Answer: A Section: (none) Explanation Explanation/Reference: With most routing protocols, the passive-interface command restricts outgoing advertisements only. But, when used with Enhanced Interior Gateway Routing Protocol (EIGRP), the effect is slightly different. QUESTION 89 Which three encapsulation layers in the OSI model are combined into the TCP/IP application layer? (Choose three) A. B. C. D. E. F. Session transport presentation application data-link network Correct Answer: ACD Section: (none) Explanation Explanation/Reference: QUESTION 90 Which function does traffic shaping perform? A. B. C. D. It buffers and queues excess packets It buffers traffic without queuing it It queues traffic without buffering it It drops packets to control the output rate Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 91 Which feature facilitates the tagging of frames on a specific VLAN ? A. B. C. D. Switching Routing encapsulation Hairpinning Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 92 After you apply the given configuration to R1, you notice that it failed to enable OSPF .Which action can you... A. B. C. D. Configure an IPv4 address on interface F0/0 Enable IPV6 unicast routing on R1. Configure a loopback interface on R1 Configure an autonomous system number an OSPF Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 93 How many bit represents the network ID in IPV6? A. B. C. D. 32 48 64 128 Correct Answer: C Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/srnd/ipv6/ipv6srnd/basics.pdf QUESTION 94 When is the most appropriate time to escalate an issue that you troubleshooting? A. B. C. D. When you lack the proper to resolve the issue. When a more urgent issue that requires your intervention is detected. When you have gathered all information about an issue. When you have been unable to resolve the issue after 30 min Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 95 Which two command can you enter to display the current time sources statistics on devices ? (Choose two) A. B. C. D. E. Show ntp associations. Show clock details Show clock. Show time. Show ntp status Correct Answer: AE Section: (none) Explanation Explanation/Reference: QUESTION 96 When an interface is configured with PortFast BPDU guard, how does the interface respond when it receives a BPDU? A. B. C. D. It continues operating normally it goes into a down/down state It becomes the root bridge for the configured VLAN It goes into an errdisable state Correct Answer: D Section: (none) Explanation Explanation/Reference: QUESTION 97 In which two formats can the IPv6 address fd15:0db8:0000:0000:0700:0003:400F:527B be written? (Choose two.) A. B. C. D. E. fd15:0db8:0000:0000:700:3:400F:527B fd15::db8::700:3:400F:527B fd15:db8:0::700:3:4F:527B fd15:0db8::700:3:4F:527B fd15:db8::700:3:400F:527B Correct Answer: AE Section: (none) Explanation Explanation/Reference: QUESTION 98 Which statement about RADIUS security is true? A. B. C. D. It supports EAP authentication for connecting to wireless networks It provides encrypted multiprotocol support Device-administration packets are encrypted in their entirely It ensures that user activity is fully anonymous Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 99 Which type of device can be replaced by the use of subinterfaces for VLAN routing? A. B. C. D. Layer 2 bridge Layer 2 switch Layer 3 switch router Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 100 Which statement about LLDP is true? A. B. C. D. It is a Cisco proprietary protocol It is configured in global configuration mode The LLDP update frequency is a fixed value It runs over the transport layer Correct Answer: B Section: (none) Explanation Explanation/Reference: http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3560/software/release/12-2_55_se/ configuration/guide/3560_scg/swlldp.html QUESTION 101 Which command can you enter to verify that a BGP connection to a remote device is established? A. B. C. D. show ip bgp summary show ip community-list show ip bgp paths show ip route Correct Answer: A Section: (none) Explanation Explanation/Reference: The established state is the proper state BGP operations. In the output of the show ip bgp summary command, if the state column has a number, then the route is in the established state. QUESTION 102 Which two statements about using leased lines for your WAN infrastructure are true? (Choose two.) A. B. C. D. E. F. Leased lines provide inexpensive WAN access Leased lines with sufficient bandwidth can avoid latency between endpoints Leased lines require little installation and maintenance expertise Leased lines provide highly flexible bandwidth scaling Multiple leased lines can share a router interface Leased lines support up to T1 link speeds Correct Answer: CD Section: (none) Explanation Explanation/Reference: QUESTION 103 Which command can you enter to verify that a 128-bit address is live and responding? A. B. C. D. traceroute telnet ping ping ipv6 Correct Answer: D Section: (none) Explanation Explanation/Reference: QUESTION 104 Which switching method duplicates the first six bytes of a frame before making a switching decision? A. B. C. D. fragement-free switching store-and-forward switching cut-through switching ASIC switching Correct Answer: C Section: (none) Explanation Explanation/Reference: QUESTION 105 Which command can you enter to determine whether serial interface 0/2/0 has been configured using HDLC encapsulation? A. B. C. D. router# show platform router# show interfaces Serial 0/2/0 router# show ip interface s0/2/0 router# show ip interface brief Correct Answer: B Section: (none) Explanation Explanation/Reference: QUESTION 106 Which logging command can enable administrators to correlate syslog messages with millisecond precision? A. B. C. D. no logging console logging buffered 4 no logging monitor service timestamps log datetime mscec Correct Answer: D Section: (none) Explanation Explanation/Reference: QUESTION 107 Which functon of the IP SLAc ICMP jitter operation can you use to determine whether a VoIP issue is caused by excessive end-to-end time? A. B. C. D. packet loss jitter successive packet loss round-trip time latency Correct Answer: D Section: (none) Explanation Explanation/Reference: QUESTION 108 Which command can you enter to determine whether a switch is operating in trunking mode? A. show ip interface brief B. show vlan C. show interfaces D. show interface switchport Correct Answer: D Section: (none) Explanation Explanation/Reference: QUESTION 109 Which feature can help you implement to reverse bandwidth for VoIP calls across the call path? A. B. C. D. PQ CBWFQ round robin RSVP Correct Answer: D Section: (none) Explanation Explanation/Reference: QUESTION 110 Which condition does the err-disabled status indicate on an Ethernet interface? A. B. C. D. E. There is a duplex mismatch The device at the other end of the connection is powered off The serial interface is disabled The interface is configured with the shutdown command E. Port security has disabled the interface The interface is fully functioning Correct Answer: E Section: (none) Explanation Explanation/Reference: QUESTION 111 Which command can you enter to display duplicate IP addresses that the DHCP server assigns? A. B. C. D. show ip dhcp conflict 10.0.2.12 show ip dhcp database 10.0.2.12 show ip dhcp server statistics show ip dhcp binding 10.0.2.12 Correct Answer: A Section: (none) Explanation Explanation/Reference: QUESTION 112 Which two statements about wireless LAN controllers are true?(Choose two) A. They can simplify the management and deploymentof wireless LANs B. C. D. E. They relay on external firewall for WLAN security They are best suited to smaller wireless networks They must be configured through a GUI over HTTP or HTTPS. They can manage mobility policies at a systemwide level. Correct Answer: AE Section: (none) Explanation Explanation/Reference: QUESTION 113 Which three statements about HSRP operation are true? (Choose three.) A. B. C. D. The virtual IP address and virtual MAC address are active on the HSRP Master router. The HSRP default timers are a 3 second hello interval and a 10 second dead interval. HSRP supports only clear-text authentication The HSRP virtual IP address must be on a different subnet than the routers’ interfaces on the same LAN. E. The HSRP virtual IP address must be the same as one of the router’s interface addresses on the LAN. F. HSRP supports up to 255 groups per interface, enabling an administrative form of load balancing. Correct Answer: ABF Section: (none) Explanation Explanation/Reference: The virtual MAC address of HSRP version 1 is 0000.0C07.ACxx, where xx is the HSRP group number in hexadecimal based on the respective interface. For example, HSRP group 10 uses the HSRP virtual MAC address of 0000.0C07.AC0A. HSRP version 2 uses a virtual MAC address of 0000.0C9F.FXXX (XXX: HSRP group in hexadecimal) QUESTION 114 lf RTR01 IS configured as shown, which three addresses will be received by other routers that are running ElGRP on the network? (Choose three.) A. B. C. D. E. F. 172.16.4.0 10.0.0.0 172.16.0.0 192.168.2.0 192.168.0.0 10.4.3.0 Correct Answer: BCD Section: (none) Explanation Explanation/Reference: