Doc 9 1 5 7
AN /9 0 1
Ae rodrom e
De sign M a nua l
Pa r t 1
Runways
Approved by the Secretary General
and published under his authority
Third Edition — 2006
International Civil Aviation Organization
Doc 9157
AN/901
Aerodrome
Design Manual
Part 1
Runways
Approved by the Secretary General
and published under his authority
Third Edition — 2006
International Civil Aviation Organization
AMENDMENTS
Amendments are announced in the supplements to the Catalogue of ICAO
Publications; the Catalogue and its supplements are available on the ICAO
website at www.icao.int. The space below is provided to keep a record of
such amendments.
RECORD OF AMENDMENTS AND CORRIGENDA
AMENDMENTS
No.
Date
CORRIGENDA
Entered by
(ii)
No.
Date
Entered by
1
31/8/06
ICAO
FOREWORD
The need for a manual providing guidance on the design of aerodromes was recognized by the
Aerodromes, Air Routes and Ground Aids (AGA) Division of ICAO at its Sixth Session in 1957. The Air
Navigation Commission, after considering the recommendations of that Division, together with other
information from the Jet Operations Requirements Panel, the Third Air Navigation Conference and Regional
Air Navigation Meetings, agreed to the publication of an aerodrome manual which was progressively revised
and added to from time to time. The structure of the Aerodrome Manual was later revised and it now
comprises three distinct documents: The Airport Services Manual (Doc 9137), The Aerodrome Design
Manual (Doc 9157), and The Airport Planning Manual (Doc 9184).
This part of the Aerodrome Design Manual fulfils the requirement for guidance material on the geometric
design of runways and associated aerodrome elements, namely, runway shoulders, runway strips, runway
end safety areas, clearways and stopways.
Much of the material included herein reproduces and is closely associated with the specifications
contained in Annex 14, Aerodromes, Volume I — Aerodrome Design and Operations. The main purpose of
this document is to facilitate the uniform application of the Annex 14, Volume I specifications.
The manual has been expanded with the inclusion of guidance material relating to runway design, which
has been relocated from the Aerodrome Design Manual (Doc 9157), Part 2 — Aprons, Taxiways and
Holding Bays. Additional guidance has been added on the design of runway turn pads and the strength
requirements of runway strips.
It is intended that this manual be kept current. Future editions will improve on this edition on the basis of
experience gained and of comments and suggestions received from users of the manual. Readers are
therefore invited to send their views, comments and suggestions on this edition, in writing, to the Secretary
General of ICAO.
___________________
(iii)
TABLE OF CONTENTS
Page
Chapter 1. General ............................................................................................................................
1.1 Introduction ............................................................................................................................
1.2 Explanation of terms ..............................................................................................................
1.3 Aerodrome reference code ....................................................................................................
1-1
1-1
1-1
1-2
Chapter 2. Configuration considerations .......................................................................................
2.1 Factors relating to the siting, orientation and number of runways .........................................
2.2 Location of threshold..............................................................................................................
2-1
2-1
2-5
Chapter 3. Runway length considerations .....................................................................................
3.1 Factors affecting the length of runways .................................................................................
3.2 Actual length of runways ........................................................................................................
3.3 Runways with stopways and/or clearways ............................................................................
3.4 Calculation of declared distances ..........................................................................................
3.5 Runway length corrections for elevation, temperature and slope..........................................
3-1
3-1
3-1
3-2
3-2
3-3
Chapter 4. Aeroplane performance parameters affecting runway length ...................................
4.1 Operational terms...................................................................................................................
4.2 Take-off length requirement...................................................................................................
4.3 Landing length requirement ...................................................................................................
4-1
4-1
4-1
4-8
Chapter 5. Physical characteristics.................................................................................................
5.1 Runways ................................................................................................................................
5.2 Runway shoulders .................................................................................................................
5.3 Runway strips.........................................................................................................................
5.4 Runway end safety areas ......................................................................................................
5.5 Clearways ..............................................................................................................................
5.6 Stopways................................................................................................................................
5-1
5-1
5-7
5-9
5-13
5-15
5-16
Chapter 6. Planning to accommodate future aircraft developments...........................................
6.1 General ..................................................................................................................................
6.2 Future aircraft trends..............................................................................................................
6.3 Aerodrome data .....................................................................................................................
6-1
6-1
6-1
6-1
Appendix 1.
Appendix 2.
Appendix 3.
Appendix 4.
Aeroplane classification by code number and letter ...............................................
The effect of variable runway slopes on take-off runway lengths..........................
Aeroplane performance curves and tables for runway planning purposes..........
Runway turn pads........................................................................................................
___________________
(v)
A1-1
A2-1
A3-1
A4-1
Chapter 1
GENERAL
1.1
INTRODUCTION
1.1.1 In view of the vital function of runways in providing for safe and efficient aircraft landings and
take-offs, it is imperative that their design take into account the operational and physical characteristics of
the aeroplanes expected to use the runway, as well as engineering and economic considerations.
1.1.2 The aerodrome elements associated with runways which are directly related to the landing and
take-off of aeroplanes are: runway strips, runway shoulders, stopways, clearways and runway end safety
areas. This manual concerns the provision of runways and these associated elements and summarizes
specifications and guidance material relating to their geometric design. Pavement strength design aspects
are covered in the Aerodrome Design Manual (Doc 9157), Part 3 — Pavements.
1.2
EXPLANATION OF TERMS
Aerodrome. A defined area on land or water (including any buildings, installations and equipment) intended
to be used either wholly or in part for the arrival, departure and surface movement of aircraft.
Aerodrome elevation. The elevation of the highest point of the landing area.
Clearway. A defined rectangular area on the ground or water under the control of the appropriate authority,
selected or prepared as a suitable area over which an aeroplane may make a portion of its initial climb
to a specified height.
Displaced threshold. A threshold not located at the extremity of a runway.
Frangible object. An object of low mass designed to break, distort or yield on impact so as to present the
minimum hazard to aircraft.
Instrument runway. One of the following types of runways intended for the operation of aircraft using
instrument approach procedures:
a) Non-precision approach runway. An instrument runway served by visual aids and a non-visual aid
providing at least directional guidance adequate for a straight-in approach.
b) Precision approach runway, category I. An instrument runway served by ILS and/or MLS and visual
aids intended for operations with a decision height not lower than 60 m (200 ft) and either a visibility
not less than 800 m or a runway visual range not less than 550 m.
c) Precision approach runway, category II. An instrument runway served by ILS and/or MLS and visual
aids intended for operations with a decision height lower than 60 m (200 ft) but not lower than 30 m
(100 ft) and a runway visual range not lower than 350 m.
1-1
1-2
Aerodrome Design Manual
d) Precision approach runway, category III. An instrument runway served by ILS and/or MLS to and
along the surface of the runway and:
A
— intended for operations with a decision height lower than 30 m (100 ft), or no decision height
and a runway visual range not less than 200 m.
B
— intended for operations with a decision height lower than 15 m (50 ft), or no decision height
and a runway visual range less than 200 m but not less than 50 m.
C
— intended for operations with no decision height and no visual range limitations.
Landing area. That part of a movement area intended for the landing or take-off of aircraft.
Manoeuvring area. That part of an aerodrome to be used for the take-off, landing and taxiing of aircraft,
excluding aprons.
Movement area. That part of an aerodrome to be used for the take-off, landing and taxiing of aircraft,
consisting of the manoeuvring area and the apron(s).
Non-instrument runway. A runway intended for the operation of aircraft using visual approach procedures.
Obstacle. All fixed (whether temporary or permanent) and mobile objects, or parts thereof, that are located
on an area intended for the surface movement of aircraft or that extend above a defined surface
intended to protect aircraft in flight.
Primary runway(s). Runway(s) used in preference to others whenever conditions permit.
Runway. A defined rectangular area on a land aerodrome prepared for the landing and take-off of aircraft.
Runway end safety area (RESA). An area symmetrical about the extended runway centre line and
adjacent to the end of the strip primarily intended to reduce the risk of damage to an aeroplane
undershooting or overrunning the runway.
Runway strip. A defined area including the runway and stopway, if provided, intended:
a) to reduce the risk of damage to aircraft running off a runway; and
b) to protect aircraft flying over it during take-off or landing operations.
Shoulder. An area adjacent to the edge of a pavement so prepared as to provide a transition between the
pavement and the adjacent surface.
Threshold. The beginning of that portion of the runway usable for landing.
1.3
AERODROME REFERENCE CODE
1.3.1 The intent of the reference code is to provide a simple method for interrelating the numerous
specifications concerning the characteristics of aerodromes so as to provide a series of aerodrome facilities
that are suitable for the aeroplanes that are intended to operate at the aerodrome. The code is composed of
two elements which are related to the aeroplane performance characteristics and dimensions. Element 1 is
Part 1. Runways
Chapter 1. General
1-3
a number based on the aeroplane reference field length and element 2 is a letter based on the aeroplane
wing span and outer main gear wheel span.
1.3.2 A particular specification is related to the more appropriate of the two elements of the code or to
an appropriate combination of the two code elements. The code letter or number within an element selected
for design purposes is related to the critical aeroplane characteristics for which the facility is provided. When
applying the relevant specifications in Annex 14, Volume I, the aeroplanes which the aerodrome is intended
to serve are first identified and then the two elements of the code.
1.3.3 An aerodrome reference code — code number and letter — which is selected for aerodrome
planning purposes shall be determined in accordance with the characteristics of the aeroplane for which an
aerodrome facility is intended. Further, the aerodrome reference code numbers and letters shall have the
meanings assigned to them in Table 1-1. A classification of representative aeroplanes by the code number
and code letter is included in Appendix 1.
1.3.4 The code number for element 1 shall be determined from Table 1-1, column 1, selecting the
code number corresponding to the highest value of the aeroplane reference field lengths of the aeroplanes
for which the runway is intended. The aeroplane reference field length is defined as the minimum field length
required for take-off at maximum certificated take-off mass, sea level, standard atmospheric conditions, still
air and zero runway slope, as shown in the appropriate aeroplane flight manual prescribed by the
certificating authority or equivalent data from the aeroplane manufacturer. Accordingly, if 1 650 m
corresponds to the highest value of the aeroplane reference field lengths, the code number selected would
be ‘3’.
1.3.5 The code letter for element 2 shall be determined from Table 1-1, column 3, by selecting the
code letter which corresponds to the greatest wing span, or the greatest outer main gear wheel span,
whichever gives the more demanding code letter of the aeroplanes for which the facility is intended. For
instance, if code letter C corresponds to the aeroplane with the greatest wing span and code letter D
corresponds to the aeroplane with the greatest outer main gear wheel span, the code letter selected would
be ‘D’.
1-4
Aerodrome Design Manual
Table 1-1.
Aerodrome reference code
CODE ELEMENT 1
CODE ELEMENT 2
Code
number
Aeroplane reference
field length
Code
letter
Wing span
Outer main gear
a
wheel span
(1)
(2)
(3)
(4)
(5)
1
Less than 800 m
A
Up to but not
including 15 m
Up to but not
including 4.5 m
2
800 m up to but not
including 1 200 m
B
15 m up to but not
including 24 m
4.5 m up to but not
including 6 m
3
1 200 m up to but not
including 1 800 m
C
24 m up to but not
including 36 m
6 m up to but not
including 9 m
4
1 800 m and over
D
36 m up to but not
including 52 m
9 m up to but not
including 14 m
E
52 m up to but not
including 65 m
9 m up to but not
including 14 m
F
65 m up to but not
including 80 m
14 m up to but not
including 16 m
a. Distance between the outside edges of the main gear wheels.
___________________
Chapter 2
CONFIGURATION CONSIDERATIONS
2.1
FACTORS RELATING TO THE SITING, ORIENTATION AND
NUMBER OF RUNWAYS
General
Note.— Flexibility to accommodate any future expansion of the runway infrastructure is fundamental to
the planning and design of airports.
2.1.1 Many factors affect the determination of the siting, orientation and number of runways. The more
important factors are:
a) weather, in particular the runway/aerodrome usability factor, as determined by wind distribution, and
the occurrence of localized fogs;
b) topography of the aerodrome site and its surroundings;
c) type and amount of air traffic to be served, including air traffic control aspects;
d) aeroplane performance considerations; and
e) environmental considerations, particularly noise.
2.1.2 The primary runway, to the extent other factors permit, should be oriented in the direction of the
prevailing wind. All runways should be oriented so that approach and departure areas are free of obstacles
and, preferably, so that aircraft are not directed over populated areas.
2.1.3 The number of runways must be sufficient to meet air traffic demands, which consist of the
number of aircraft arrivals and departures, and the mixture of aircraft types, to be accommodated in one
hour during the busiest periods. The decision as to the total number of runways to be provided should also
take into account the aerodrome usability factor and economic considerations.
Type of operation
2.1.4 Particular attention should be paid to whether the aerodrome is to be used in all meteorological
conditions or only in visual meteorological conditions, and whether it is intended for use by day and night or
only by day.
2.1.5 When a new instrument runway is being located, particular attention needs to be given to areas
over which aeroplanes will be required to fly when following instrument approach and missed approach
procedures, so as to ensure that obstacles in these areas or other factors will not restrict the operation of the
aeroplanes for which the runway is intended.
2-1
2-2
Aerodrome Design Manual
Wind
2.1.6 The number and orientation of runways at an aerodrome should be such that the usability factor
of the aerodrome is not less than 95 per cent for the aeroplane that the aerodrome is intended to serve.
2.1.7 In the application of the 95 per cent usability factor it should be assumed that landing or take-off
of aeroplanes is, in normal circumstances, precluded when the cross-wind component exceeds:
— 37 km/h (20 kt) in the case of aeroplanes whose reference field length is 1 500 m or over, except
that when poor runway braking action owing to an insufficient longitudinal coefficient of friction is
experienced with some frequency, a cross-wind component not exceeding 24 km/h (13 kt) should be
assumed;
— 24 km/h (13 kt) in the case of aeroplanes whose reference field length is 1 200 m or up to but not
including 1 500 m; and
— 19 km/h (10 kt) in the case of aeroplanes whose reference field length is less than 1 200 m.
2.1.8 The selection of data to be used for the calculation of the usability factor should be based on
reliable wind distribution statistics that extend over as long a period as possible, preferably of not less than
five years. The observations used should be made at least eight times daily and spaced at equal intervals of
time, and should take into account the following:
a) wind statistics used for the calculation of the usability factor are normally available in ranges of
speed and direction, and the accuracy of the results obtained depends, to a large extent, on the
assumed distribution of observations within these ranges. In the absence of any sure information as
to the true distribution, it is usual to assume a uniform distribution since, in relation to the most
favourable runway orientations, this generally results in a slightly conservative figure for the usability
factor;
b) the maximum mean cross-wind components given in 2.1.7 refer to normal circumstances. There are
some factors which may require that a reduction of those maximum values be taken into account at
a particular aerodrome. These include:
1) the wide variations which may exist, in handling characteristics and maximum permissible crosswind components, among diverse types of aeroplanes (including future types) within each of the
three groups given in 2.1.7;
2) prevalence and nature of gusts;
3) prevalence and nature of turbulence;
4) the availability of a secondary runway;
5) the width of runways;
6) the runway surface conditions – water, snow, slush and ice on the runway materially reduce the
allowable cross-wind component; and
7) the strength of the wind associated with the limiting cross-wind component.
Part 1. Runways
Chapter 2. Configuration considerations
2-3
2.1.9 The 95 per cent criterion recommended by Annex 14, Volume I is applicable to all conditions of
weather; nevertheless, it is useful to examine wind speed and direction for different visibility conditions.
Weather records can usually be obtained from government weather bureaux. The velocities are generally
grouped into 22.5 degree increments (16 points of the compass). The weather records contain the
percentage of time certain combinations of ceiling and visibility occur (e.g. ceiling, 500 to 274 m; visibility,
4.8 to 9.7 km), and the percentage of time winds of a specific velocity occur from different directions; for
example NNE, 2.6 to 4.6 kt. The directions are relative to true north. Often wind data for a new location have
not been recorded. If that is the case, records of nearby measuring stations should be consulted. If the
surrounding area is fairly level, the records of these stations should indicate the winds at the site of the
proposed aerodrome. However, if the terrain is hilly, the wind pattern often is dictated by the topography,
and it is dangerous to utilize the records of stations some distance from the site. In that event, a study of the
topography of the region and consultation with local residents may prove useful but a wind study of the site
should be initiated. Such a study would involve the installation of wind gauges and the keeping of wind
records. Guidance material on the preparation and analysis of wind data for aerodrome planning purposes is
given in the Airport Planning Manual (Doc 9184) Part 1 — Master Planning.
Visibility conditions
2.1.10
Wind characteristics under poor visibility conditions are often quite different from those
experienced under good visibility conditions. Therefore a study should be made of the wind conditions
occurring with poor visibility and/or low cloud base at the aerodrome, including the frequency of occurrence
and the accompanying wind direction and speed.
Topography of the aerodrome site, its approaches and surroundings
2.1.11
The topographical features of the aerodrome and its surroundings should be examined. In
particular the following should be reviewed:
a) compliance with the obstacle limitation surfaces;
b) current and future land use. The orientation and layout should be selected so as to protect as far as
possible the particularly sensitive areas such as residential, school and hospital zones from the
discomfort caused by aircraft noise;
c) current and future runway lengths to be provided;
d) construction costs; and
e) the possibility of installing suitable non-visual and visual aids for approach-to-land.
Air traffic in the vicinity of the aerodrome
2.1.12
When considering the siting of runways the following should be taken into account:
a) proximity of other aerodromes or ATS routes;
b) traffic density; and
c) air traffic control and missed approach procedures.
2-4
Aerodrome Design Manual
Environmental factors
2.1.13 The effect of a particular runway alignment on wild life, the general ecology of the area, and
noise-sensitive areas of communities should be considered.
2.1.14 The noise level produced by aircraft operations at and around the aerodrome is generally
considered a primary environmental cost associated with the facility. Most noise exposure lies within the
land area immediately beneath and adjacent to the aircraft approach and departure paths. Noise levels are
generally measured through some formulation of decibel level, duration and number of occurrences. A large
number of noise measuring techniques exist (see Annex 16 — Environmental Protection and
Recommended Method for Computing Noise Contours around Airports (Cir 205)). Proper site selection and
adjacent land use planning can serve to greatly reduce and possibly eliminate the noise problem associated
with the aerodrome.
Parallel runways
2.1.15 The number of runways to be provided in each direction depends on the forecast of aircraft
movements (see the Airport Planning Manual (Doc 9184), Part 1).
2.1.16 VMC operations. Where parallel runways are provided for simultaneous use under visual
meteorological conditions only, the minimum distance between their centre lines should be:
— 210 m where the higher code number is 3 or 4;
— 150 m where the higher code number is 2; and
— 120 m where the higher code number is 1.
2.1.17 IMC operations. Where parallel runways are provided for simultaneous operations under
instrument meteorological conditions, the minimum separation distance between their centre lines should be:
— 1 035 m for independent parallel approaches;
— 915 m for dependent parallel approaches;
— 760 m for independent parallel departures;
— 760 m for segregated parallel operations;
except that:
a) for segregated parallel operations the specified separation distance:
1) may be decreased by 30 m for each 150 m that the arrival runway is staggered toward the
arriving aircraft, to a minimum of 300 m; and
2) should be increased by 30 m for each 150 m that the arrival runway is staggered away from the
arriving aircraft;
b) lower separation distances than those specified above may be applied if, after aeronautical study, it
is determined that such lower separation distances would not affect the safety of operations of
aircraft.
Part 1. Runways
Chapter 2. Configuration considerations
2-5
2.1.18 Guidance on planning and conducting simultaneous operations on parallel or near-parallel
instrument runways is contained in the Manual of Simultaneous Operations on Parallel or Near-Parallel
Instrument Runways (SOIR) (Doc 9643).
Terminal area between parallel runways
2.1.19 To minimize taxi operations across active runways and to better utilize the area between the
parallel runways, the terminal area and other operational areas may be placed between parallel runways. To
accommodate these areas, greater separation distances than those recommended in the preceding
paragraph may be required.
2.2
LOCATION OF THRESHOLD
2.2.1 The threshold is normally located at the extremity of a runway, if there are no obstacles
penetrating above the approach surface. In some cases, however, due to local conditions it may be
desirable to displace the threshold permanently (see 2.2.3). When studying the location of a threshold,
consideration should also be given to the height of the ILS reference datum and the determination of the
obstacle clearance limits. (Specifications concerning the height of the ILS reference datum are given in
Annex 10, Volume I.)
2.2.2 In determining that no obstacle penetrates above the approach surface, account should be taken
of mobile objects (vehicles on roads, trains, etc.) at least within that portion of the approach area within
1 200 m longitudinally from the threshold and of an overall width of not less than 150 m.
2.2.3 If an object extends above the approach surface and the object cannot be removed,
consideration should be given to displacing the threshold permanently.
2.2.4 To meet the obstacle limitation objectives of Annex 14, Volume I, Chapter 4, the threshold
should ideally be displaced down the runway for the distance necessary to ensure that the approach surface
is clear of obstacles.
2.2.5 However, displacement of the threshold from the runway extremity will inevitably cause reduction
of the landing distance available, and this may be of greater operational significance than penetration of the
approach surface by marked and lighted obstacles. A decision to displace the threshold, and the extent of
such displacement, should therefore have regard to an optimum balance between the considerations of
clear approach surfaces and adequate landing distance. In deciding this question, account will need to be
taken of the types of aeroplanes which the runway is intended to serve, the limiting visibility and cloud base
conditions under which the runway will be used, the position of the obstacles in relation to the threshold and
extended centre line and, in the case of a precision approach runway, the significance of the obstacles to
the determination of the obstacle clearance limit.
2.2.6 Notwithstanding the consideration of landing distance available, the selected position for the
threshold should not be such that the obstacle-free surface to the threshold is steeper than 3.3 per cent
where the code number is 4 or steeper than 5 per cent where the code number is 3.
___________________
Chapter 3
RUNWAY LENGTH CONSIDERATIONS
3.1
3.1.1
FACTORS AFFECTING THE LENGTH OF RUNWAYS
Factors which have a bearing on the runway length to be provided are:
a) performance characteristics and operating masses of the aeroplanes to be served;
b) weather, particularly surface wind and temperature;
c) runway characteristics such as slope and surface condition; and
d) aerodrome location factors, for example, aerodrome elevation which affects the barometric pressure
and topographical constraints.
3.1.2 The relationship between runway length and aeroplane performance characteristics is discussed
in Chapter 4. The greater the head wind down a runway, the shorter the runway length required by an
aeroplane taking off or landing. Conversely, a tail wind increases the length of runway required. The higher
the temperature, the longer the runway required because higher temperatures create lower air densities
resulting in lower output of thrust and reduced lift. The effect of runway slopes on runway length
requirements is discussed in detail in Appendix 2, however it is evident that an aeroplane taking off on an
uphill gradient requires more runway length than it would on a level or downhill gradient; the specific amount
depends on the elevation of the aerodrome and the temperature. All other factors being equal, the higher the
elevation of the aerodrome with correspondingly lower barometric pressure, the longer the runway required.
The runway length which can be provided at an aerodrome may be constrained by property boundaries or
topographical features such as mountains, the sea or steep valleys.
3.2
ACTUAL LENGTH OF RUNWAYS
Primary runways
3.2.1 Except where a runway is associated with a stopway and/or clearway, the actual runway length
to be provided for a primary runway should be adequate to meet the operational requirements of the
aeroplanes for which the runway is intended and should be not less than the longest length determined by
applying the corrections for local conditions to the operations and performance characteristics of the relevant
aeroplanes.
3.2.2 Both take-off and landing requirements need to be considered when determining the length of
runway to be provided and the need for operations to be conducted in both directions of the runway. Local
conditions that may need to be considered include elevation, temperature, runway slope, humidity and the
runway surface characteristics.
3-1
3-2
Aerodrome Design Manual
3.2.3 When performance data on aeroplanes for which the runway is intended are not known, the
actual length of a primary runway may be determined by application of general correction factors as
described in 3.5. However, it is advisable that the aeroplane manufacturers document entitled Aeroplane
Characteristics for Airport Planning — NAS 3601 be consulted for the most up-to-date information.
Secondary runways
3.2.4 The length of a secondary runway should be determined similarly to primary runways except that
it needs only to be adequate for those aeroplanes which require to use that secondary runway in addition to
the other runway or runways in order to obtain a usability factor of at least 95 per cent.
3.2.5 Flight manuals providing data on aeroplane operational requirements and performance
characteristics are available for most modern aeroplanes. Aeroplane performance curves and tables for
landing and take-off operations have also been developed for basic runway length planning purposes.
Information on these aeroplane performance curves and tables is given in Appendix 3.
3.3
RUNWAYS WITH STOPWAYS AND/OR CLEARWAYS
3.3.1 Where a runway is associated with a stopway or clearway, an actual runway length less than
that resulting from application of 3.2.2 or 3.2.3, as appropriate, may be considered satisfactory, but in such a
case any combination of runway, stopway and/or clearway provided should permit compliance with the
operational requirements for take- off and landing of the aeroplanes the runway is intended to serve.
3.3.2 The decision to provide a stopway and/or a clearway as an alternative to an increased length of
runway will depend on the physical characteristics of the area beyond the runway end, and on the operating
performance requirements of the prospective aeroplanes. The runway, stopway and clearway lengths to be
provided are determined by the aeroplane take-off performance, but a check should also be made of the
landing distance required by the aeroplanes using the runway to ensure that adequate runway length is
provided for landing. The length of a clearway, however, cannot exceed half the length of take-off run
available.
3.4
CALCULATION OF DECLARED DISTANCES
3.4.1 The introduction of stopways and clearways and the use of displaced thresholds on runways has
created a need for accurate information regarding the various physical distances available and suitable for
the landing and take-off of aeroplanes. For these purposes, the term “declared distances” is used with the
following four distances associated with a particular runway:
a) Take-off run available (TORA), i.e. the length of runway declared available and suitable for the
ground run of an aeroplane taking off.
b) Take-off distance available (TODA), i.e. the length of the take-off run available plus the length of the
clearway, if provided.
c) Accelerate stop distance available (ASDA), i.e. the length of the take-off run available plus the
length of the stopway, if provided.
Part 1. Runways
Chapter 3. Runway length considerations
3-3
d) Landing distance available (LDA), i.e. the length of runway which is declared available and suitable
for the ground run of an aeroplane landing.
3.4.2 Annex 14, Volume I, calls for the calculation of declared distances for a runway intended for use
by international commercial air transport, and Annex 15 calls for the reporting of declared distances for each
direction of the runway in the State Aeronautical Information Publication (AIP). Figure 3-1 illustrates typical
cases, and Figure 3-2 shows a tabulation of declared distances.
3.4.3 Where a runway is not provided with a stopway or clearway and the threshold is located at the
extremity of the runway, the four declared distances should normally be equal to the length of the runway as
shown in Figure 3-1A.
3.4.4 Where a runway is provided with a clearway (CWY), then the TODA will include the length of
clearway as shown in Figure 3-1B.
3.4.5 Where a runway is provided with a stopway (SWY), then the ASDA will include the length of
stopway as shown in Figure 3-1C.
3.4.6 Where a runway has a displaced threshold, then the LDA will be reduced by the distance the
threshold is displaced as shown in Figure 3-1D. A displaced threshold affects only the LDA for approaches
made to that threshold; all declared distances for operations in the reciprocal direction are unaffected.
3.4.7 Figures 3-1B through 3-1D illustrate a runway provided with a clearway, a stopway or having a
displaced threshold. Where more than one of these features exist then more than one of the declared
distances will be modified - but the modification will follow the same principle illustrated. Figures 3-1E and
3-1F illustrate two situations where all these features exist.
3.4.8 A suggested format for providing information on declared distances is given in Figure 3-2. If a
runway direction cannot be used for take-off or landing, or both, because it is operationally forbidden, then
this should be declared and the words “not usable” or the abbreviation “NU” entered.
3.4.9 Where provision of a runway end safety area may involve encroachment in areas where it would
be particularly prohibitive to implement, and the appropriate authority considers a runway end safety area
essential, consideration may have to be given to reducing some of the declared distances.
3.5
RUNWAY LENGTH CORRECTIONS FOR ELEVATION,
TEMPERATURE AND SLOPE
3.5.1 As stated in 3.2.3, when the appropriate flight manual is not available the runway length must be
determined by applying general correction factors. As a first step, a basic length should be selected for the
runway adequate to meet the operational requirements of the aeroplanes for which the runway is intended.
This basic length is a runway length selected for aerodrome planning purposes which is required for take-off
or landing under standard atmospheric conditions for zero elevation, zero wind and zero runway slope.
3.5.2 The basic length selected for the runway should be increased at the rate of 7 per cent per 300 m
elevation.
3.5.3 The length of runway determined under 3.5.2 should be further increased at the rate of 1 per
cent for every 1°C by which the aerodrome reference temperature exceeds the temperature in the standard
atmosphere for the aerodrome elevation (see Table 3-1). If, however, the total correction for elevation and
3-4
Aerodrome Design Manual
A
D
TORA
TODA
ASDA
LDA
LDA
TORA
TODA
ASDA
B
E
CWY
TORA
ASDA
LDA
SWY CWY
LDA
TORA
ASDA
TODA
TODA
SWY
CWY
F
C
LDA
TORA
SWY
TORA
TODA
LDA
ASDA
TODA
ASDA
(All above declared distances are illustrated
for operations from left to right)
Threshold
Displaced
threshold
150 m
1 850 m
Threshold
27
Runway
09
Stopway
Illustration of declared distances
Threshold
Clearway
350 m
Displacement
Runway
extremity
Figure 3-1.
17
Runway
Figure 3-2.
35
1 800 m
Runway
09
27
17
35
TORA
m
2 000
2 000
NU
1 800
Determination of declared distances
Clearway
580 m
300 m
Stopway
ASDA
m
2 300
2 350
NU
1 800
TODA
m
2 580
2 350
NU
1 800
LDA
m
1 850
2 000
1 800
NU
Part 1. Runways
Chapter 3. Runway length considerations
3-5
temperature exceeds 35 per cent, the required corrections should be obtained by means of a specific study.
The operational characteristics of certain aeroplanes may indicate that these correction constants for
elevation and temperature are not appropriate, and that they may need to be modified by results of
aeronautical study based upon conditions existing at the particular site and the operating requirements of
such aeroplanes.
3.5.4 Where the basic length determined by take-off requirements is 900 m or over, that length should
be further increased at the rate of 10 per cent for each 1 per cent of the runway slope as defined in 5.1.4.
3.5.5 At aerodromes where temperature and humidity are both high, some addition to the runway
length determined under 3.5.4 may be necessary, even though it is not possible to give exact figures for the
increased lengths required.
Table 3-1.
Table of Standard Atmosphere Values
Altitude
(m)
Temperature
(Centigrade)
Pressure
3
(Kg/m )
0
15.00
1.23
500
11.75
1.17
1 000
8.50
1.11
1 500
5.25
1.06
2 000
2.00
1.01
2 500
–1.25
0.96
3 000
–4.50
0.91
3 500
–7.75
0.86
4 000
–10.98
0.82
4 500
–14.23
0.78
5 000
–17.47
0.74
5 500
–20.72
0.70
6 000
–23.96
0.66
3-6
Aerodrome Design Manual
Examples of the application of runway length corrections
3.5.6
The following examples illustrate the application of the runway length corrections.
Example 1:
a) Data:
1) runway length required for landing at sea
level in standard atmospheric conditions
2 100 m
2) runway length required for take-off at a
level site at sea level in standard
atmospheric conditions
1 700 m
3) aerodrome elevation
150 m
4) aerodrome reference temperature
24°C
5) temperature in the standard atmosphere for 150 m
14.025°C
6) runway slope
0.5%
b) Corrections to runway take-off length:
1) runway take-off length corrected for
elevation =
1 700 x 0.07 x
150
+ 1 700 =
300
1 760 m
2) runway take-off length corrected for
elevation and temperature =
[1 760 x (24 – 14.025) x 0.01 ] + 1 760 =
1 936 m
3) runway take-off length corrected for
elevation, temperature and slope =
[1 936 x 0.5 x 0.10 ] + 1 936 =
2 033 m
c) Correction to runway landing length:
runway landing length corrected for elevation =
2 100 x 0.07 x
150
+ 2 100 =
300
d) Actual runway length =
2 174 m
2 175 m
Part 1. Runways
Chapter 3. Runway length considerations
3-7
Example 2:
a) Data:
1) runway length required for landing at sea
level in standard atmospheric conditions
2 100 m
2) runway length required for take-off at a
level site at sea level in standard
atmospheric conditions
2 500 m
3) aerodrome elevation
150 m
4) aerodrome reference temperature
24°C
5) temperature in the standard atmosphere for
150 m
14.025°C
6) runway slope
0.5%
b) Correction to runway take-off length:
1) runway take-off length corrected for
elevation =
2 500 x 0.07 x
150
+ 2 500 =
300
2 588 m
2) runway take-off length corrected for
elevation and temperature =
[2 588 x (24 – 14.025) x 0.01 ] + 2 588 =
2 846 m
3) runway take-off length corrected for
elevation, temperature and slope =
[2 846 x 0.5 x 0.10 ] + 2 846 =
2 988 m
c) Correction to runway landing length:
runway landing length corrected for elevation =
2 100 x 0.07 x
150
+ 2 100 =
300
2 174 m
d) Actual runway length =
2 988 m
___________________
Chapter 4
AEROPLANE PERFORMANCE PARAMETERS AFFECTING
RUNWAY LENGTH
4.1
OPERATIONAL TERMS
4.1 Before discussing the relationship between aeroplane performance parameters and runway length
requirements it is necessary to explain the following operational terms:
a) Decision speed (V1) is the speed chosen by the operator at which the pilot, having recognized a
failure of the critical engine, decides whether to continue the flight or initiate the application of the
first retarding device. If the engine failure occurs before the decision speed is reached, the pilot
should stop; if failure occurs later, the pilot should not stop but should continue the take-off. As a
general rule a decision speed is selected which is lower, or at most equal, to the take-off safety
speed (V2). It should however exceed the lowest speed at which the aeroplane can still be controlled
on or near the ground in the case of failure of the most critical engine; this speed may be given in
the aeroplane flight manual.
b) Take-off safety speed (V2) is the minimum speed at which the pilot is allowed to climb after attaining
a height of 10.7 m (35 ft) to maintain at least the minimum required climb gradient above the take-off
surface during a take-off with one engine inoperative.
c) Rotation speed (VR) is the speed at which the pilot initiates rotation of the aeroplane to cause raising
of the landing gear.
d) Lift-off speed (VLOF) in terms of calibrated airspeed, is the speed at which the aeroplane first
becomes airborne.
4.2
TAKE-OFF LENGTH REQUIREMENT
4.2.1 The aeroplane performance operating limitations require a length which is enough to ensure that
the aeroplane can, after starting a take-off, either be brought safely to a stop or complete the take-off safely.
For the purpose of discussion it is supposed that the runway, stopway and clearway lengths provided at the
aerodrome are only just adequate for the aeroplane requiring the longest take-off and accelerate-stop
distances, taking into account its take-off mass, runway characteristics and ambient atmospheric conditions.
Under these circumstances, there is for each take-off, a speed, called the decision speed (V1); below this
speed, the take-off must be abandoned if an engine fails, while above it the take-off must be completed. A
very long take-off run and take-off distance would be required to complete a take-off when an engine fails
before the decision speed is reached because of the insufficient speed and the reduced power available.
There would be no difficulty in stopping in the remaining accelerate-stop distance available provided action
is taken immediately. In these circumstances the correct course of action would be to abandon the take-off.
4-1
4-2
Aerodrome Design Manual
4.2.2 On the other hand, if an engine fails after the decision speed is reached, the aeroplane will have
sufficient speed and power available to complete the take-off safely in the remaining take-off distance
available. However, because of the high speed, there would be difficulty in stopping the aeroplane in the
remaining accelerate-stop distance available.
4.2.3 The decision speed is not a fixed speed for any aeroplane, but can be selected by the pilot within
limits to suit the accelerate-stop and take-off distance available, aeroplane take-off mass, runway
characteristics, and ambient atmospheric conditions at the aerodrome. Normally, a higher decision speed is
selected as the accelerate-stop distance available increases.
4.2.4 A variety of combinations of accelerate-stop distances required and take-off distances required
can be obtained to accommodate a particular aeroplane, taking into account the aeroplane take-off mass,
runway characteristics, and ambient atmospheric conditions. Each combination requires its particular length
of take-off run.
4.2.5 The most familiar case is where the decision speed is such that the take-off distance required is
equal to the accelerate-stop distance required; this value is known as the balanced field length. Where
stopway and clearway are not provided, these distances are both equal to the runway length. However, if
landing distance is for the moment ignored, runway is not essential for the whole of the balanced field length,
as the take-off run required is, of course, less than the balanced field length. The balanced field length can,
therefore, be provided by a runway supplemented by an equal length of clearway and stopway, instead of
wholly as a runway. If the runway is used for take-off in both directions, an equal length of clearway and
stopway has to be provided at each runway end. The saving in runway length is, therefore, bought at the
cost of a greater overall length.
4.2.6 In case economic considerations preclude the provision of stopway and, as a result only runway
and clearway are to be provided, the runway length (neglecting landing requirements) should be equal to the
accelerate-stop distance required or the take-off run required whichever is the greater. The take-off distance
available will be the length of the runway plus the length of clearway.
4.2.7 The minimum runway length and the maximum stopway or clearway length to be provided may
be determined as follows, from the data in the Aeroplane Flight Manual for the aeroplane considered to be
critical from the viewpoint of runway length requirements:
a) if a stopway is economically possible, the lengths to be provided are those for the balanced field
length. The runway length is the take-off run required or the landing distance required, whichever is
the greater. If the accelerate-stop distance required is greater than the runway length so determined,
the excess may be provided as stopway, usually at each end of the runway. In addition, a clearway
of the same length as the stopway must also be provided;
b) if a stopway is not to be provided, the runway length is the landing distance required, or if it is
greater, the accelerate-stop distance required which corresponds to the lowest practical value of the
decision speed. The excess of the take-off distance required over the runway length may be
provided as clearway, usually at each end of the runway.
4.2.8 In addition to the above consideration, the concept of clearways in certain circumstances can be
applied to a situation where the take-off distance required for all engines operating exceeds that required for
the engine failure case.
4.2.9 The economy of a stopway can be entirely lost if, after each usage, it must be regraded and
compacted. Therefore, it should be designed to withstand at least a certain number of loadings of the
aeroplane which the stopway is intended to serve without inducing structural damage to the aeroplane.
Part 1. Runways
Chapter 4. Aeroplane performance parameters effecting runway length
4-3
4.2.10 Taking as a schematic illustration (Figure 4-1 (a)) the case of an aeroplane standing at the
entrance end A of a runway, the pilot starts the take-off, the aeroplane accelerates and approaches the
decision speed (V1) point B. A sudden and complete failure of an engine is assumed to occur and is
recognized by the pilot as the decision speed (V1) is attained. The pilot can either:
— brake until the aeroplane comes to a standstill at point Y (the accelerate-stop distance); or
— continue accelerating until reaching the rotation speed (VR), point C, at which time the aeroplane
rotates and becomes airborne at the lift-off speed (VLOF), point D, after which it reaches the end of
the take-off run, point X, and continues to the 10.7 m (35 ft) height at the end of the take-off distance,
point Z.
4.2.11 Figure 4-1 (b) illustrates a normal all-engines operating case where d’1 and d’3 are similar to d1
and d3, respectively, in Figure 4-1 (a).
4.2.12 The engine-inoperative take-off and accelerate-stop distances will vary according to the
selection of the decision speed (V1). If the decision speed is reduced, the distance to point B (Figure 4-1 (a))
is reduced, as is the accelerate-stop distance; but the take-off run and take-off distances are increased as a
larger part of the take-off manoeuvre is carried out with an engine inoperative. Figure 4-2 illustrates the
probable relationship which may exist between the accelerate-stop distances, the take-off distances, and the
take-off runs with respect to variations in the decision speed, (V1), within the limits stated in 4.1.1.
4.2.13 The take-off performance characteristics of a given aeroplane will not necessarily encompass
the range of decision speeds shown in Figure 4-2. Rather, under specified conditions, an individual
aeroplane may be found to be restricted to within one of the areas indicated by the horizontal brackets a, b
or c. In the case illustrated by bracket a, the take-off distance with an engine inoperative is critical. The
logical selection of V1, point (1), would be to have it equal V2 or VR depending on the aeroplane’s take-off
characteristics. In the case illustrated by bracket b, the accelerate-stop distance is critical from the V2 speed
down to a point where ground controllability may become critical. The logical selection of V1 would be to
keep it as low as is practical, point (2). In the case illustrated by bracket c, which is the more general case,
the accelerate-stop distance is critical at V1 speeds near the V2 speed and the take-off distance is critical at
speeds near the minimum speed for controllability, in this case the V1 speed selected is usually the optimum,
i.e. the V1 at which the two distances are equal, point (3). If the all-engines operating take-off distance is
critical in one or more of the cases cited, the range of possible V1 speeds is somewhat enlarged because
that distance is independent of the V1 speed.
4.2.14 It will be seen that the total length required is the least in the case of the optimum decision
speed (V1), and this is always true. Normally, therefore, the runway should be constructed to this length.
However, the part of the accelerate-stop distance not required for the take-off run (the length B in Figure 4-3)
will be used very rarely and may therefore be constructed more economically than the part A required for
take-off run, i.e. the runway itself. Further, during take-off, the length B + C will only be flown over during the
initial climb to the height specified in Annex 6 and is not expected to bear the mass of the aircraft; it requires
only to be clear of obstacles.
4.2.15 In certain circumstances, the construction of runways with surfaces such as stopways and
clearways may prove to be more advantageous than the construction of conventional runways. The choice
between a solution involving a conventional runway and one in which a combination of these surfaces is
used, will depend on the local physical and economic conditions, size and clearances of the site, soil
characteristics, possibility of acquiring land, plans for future development, nature and cost of available
materials, time interval required for carrying out the work, acceptable level of maintenance charges, etc. In
particular, the construction of stopways at each end of the runway (since there are normally two directions
for take-off) may frequently be an economical first stage in the extension of an existing runway. The
4-4
Aerodrome Design Manual
VLOF
V1
A
B
V2
10.7 m
(35′)
VR
C
D
X
Y
Z
2
Take-off run (TOR)
d1
Accelerate-stop distance (ASD)
d2
Take-off distance (TOD)
d3
a) Critical Engine Inoperative
V2
A
10.7 m
(35′)
VR VLOF
X′
d′1 (TOR)
d′3 (TOD)
b) All Engines Operating
Figure 4-1.
Z′
Part 1. Runways
Chapter 4. Aeroplane performance parameters effecting runway length
4-5
c
a
b
d2(ASD)
1
2
S
(Distance)
1.15d′3(TOD)
3
d3(TOD)
V1
Figure 4-2.
stopways, which are not used for landings and are used by the aeroplane only in exceptional cases during
take-off, can frequently be provided without considerable expenditure, and their establishment is
operationally equivalent for the aeroplane to a lengthening of the runway.
4.2.16 In order to choose between the non-conventional runway and the preferred conventional
runway, it is necessary to determine the proportions of clearway or clearway/stopway which may be
provided. Figure 4-3 illustrates how this can be done for a particular aeroplane under one set of conditions of
altitude, temperature, take-off mass, etc. As shown above, the distance for the take-off run, the take-off
distance and the accelerate-stop distance for a particular aeroplane during take-off depend on the choice of
the decision speed V1. Within a certain range (as noted in 4.1.1) any value of V1 can be chosen and
consequently many combinations of runway, stopway and clearway would appear to be possible. The
minimum requirements for the design of a non- conventional runway will normally include a runway and a
clearway, or a runway and a combination clearway/stopway, depending on the V1 speeds used. This is
illustrated in Figure 4-3.
4-6
Aerodrome Design Manual
c
b
a
d2(ASD)
Cle
arw
ay
1
2
B
Runway end
Stopway
3
C
S
(Distance)
A
Clea
rwa
y/S
topw
ay
d3(TOD)
d1(TOR)
V1
a) Engine Inoperative Critical
c
b
a
d2(ASD)
Cle
arw
ay
Stopway
1
C
Clearway / Stopway
1.15 d′1 (TOR)
B
3
Runway end
A
S
(Distance)
1.15 d′3 (TOD)
2
d3(TOD)
d1(TOR)
V1
b) All Engines Operating Critical
Figure 4-3.
Part 1. Runways
Chapter 4. Aeroplane performance parameters effecting runway length
c
W1
W1
4-7
a
b
d2(ASD)
d2(ASD)
W0
W1
W0
W1
1′
Clearway
2′
1
2
3′
Clearway
S
(Distance)
Stopway
d1(TOR)
W1
d3(TOD)
d3(TOD)
W0
d3(TOD)
Existing runway
3
Stopway
W1
d3(TOD)
W0
(d1 ) (TOR)
W0 = initial aircraft mass
W1 = final aircraft mass
a
V1
b
Figure 4-4.
4.2.17 Expansion of a conventional runway to a non-conventional runway to accommodate an
increase in mass of the critical aeroplane is illustrated in Figure 4-4. In Figure 4-4 (a), the critical aeroplane
uses the optimum V1 speed, point 3, at mass W o on the existing runway. With the mass increased to W 1, the
optimum V1 speed is somewhat increased, point 3’. The mass increase is limited to that which results in
take-off run (d1) equal to the length of runway. The additional take-off distance and accelerate-stop distance
can be accommodated by a combination clearway/stopway. In Figure 4-4 (b), two cases are cited. In the first
case, the aeroplane’s V1 speed is at point 1. The new V1 speed, point 1’, would increase if the initial climb
out speed (V2) increased due to the mass change. The mass increase is limited to that which would result in
a take-off run (d1) at mass W 1 equal to the take-off distance (d3) at mass W o. The increase in take-off
distance can be accommodated by a clearway. In the second case, the aeroplane’s V1 speed is at point 2.
The V1 speed, point 2’, would probably be held constant. The mass increase would be limited by the
increased take-off distance d3 at mass W 1 if a clearway was not to be provided. The increase in acceleratestop distance can be accommodated by a stopway. Note that any further increase in mass will require the
use of a combined clearway/stopway. The effect caused by the all-engines-operating case can readily be
seen by a comparison of Figure 4-3, (a) and (b). Lower values of V1 are of no interest since they result in
both greater take- off run and take-off distance.
4.2.18
The runway length determined from the take-off performance charts is the greater of either:
a) the balanced field length, that is, the runway length required when the take-off distance with one
engine inoperative and accelerate-stop distance are equal; or
b) 115 per cent of the take-off distance with all engines operative.
4-8
Aerodrome Design Manual
4.3
LANDING LENGTH REQUIREMENT
Although landing lengths are normally not critical, aeroplane landing performance charts should be
consulted to check that runway length requirements for take-off provide adequate runway length for landing.
In general a landing length is determined that provides for an aeroplane landing after clearing all obstacles
in the approach path by a safe margin and stopping safely. Allowance shall be made for variations in the
approach and landing techniques of particular aeroplanes, if such allowance has not been made in the
scheduling of performance data. The runway length determined from a landing performance chart is the
aeroplane’s landing distance required divided by 0.6. Where the length of runway required for landing is
greater than that required for the take-off run, this will determine the minimum length of runway required.
___________________
CHAPTER 5
PHYSICAL CHARACTERISTICS
5.1
RUNWAYS
Width
5.1.1
The width of a runway should be not less than the appropriate dimension specified in Table 5-1:
5.1.2 The runway widths shown in Table 5-1 are the minimum widths considered necessary to ensure
safety of operations. The factors affecting the width of runways are:
a) deviation of an aeroplane from the centre line at touchdown;
b) cross-wind condition;
c) runway surface contamination (e.g. rain, snow, slush or ice);
d) rubber deposits;
e) crab landing approaches used in cross-wind conditions;
f)
approach speeds used;
g) visibility; and
h) Human Factors.
Table 5-1.
Runway widths
Code Letter
Code Number
A
B
C
D
E
F
a
18 m
18 m
23 m
—
—
—
2
a
23 m
23 m
30 m
—
—
—
3
30 m
30 m
30 m
45 m
—
—
4
—
—
45 m
45 m
45 m
60 m
1
a.
The width of a precision approach runway should be not less than 30 m where the code number is 1 or 2.
5-1
5-2
Aerodrome Design Manual
5.1.3 Simulator studies of aborted take-offs on contaminated runways, with one engine failure and in
cross-wind conditions, and through actual observation at many airports, indicate that the specified runway
width for each aerodrome reference code is operationally required. Should aircraft operations be planned on
runways with lesser widths than specified above, the consequent impact on safety, efficiency and regularity
of operations and on airport capacity must be studied.
Longitudinal slopes
5.1.4 The slope computed by dividing the difference between the maximum and minimum elevation
along the runway centre line by the runway length should not exceed:
— 1 per cent where the code number is 3 or 4; and
— 2 per cent where the code number is 1 or 2.
5.1.5
Along no portion of a runway should the longitudinal slope exceed:
— 1.25 per cent where the code number is 4, except that for the first and last quarter of the length of
the runway the longitudinal slope should not exceed 0.8 per cent;
— 1.5 per cent where the code number is 3, except that for the first and last quarter of the length of a
precision approach runway category II or III the longitudinal slope should not exceed 0.8 per cent;
and
— 2 per cent where the code number is 1 or 2.
Longitudinal slope changes
5.1.6 Where slope changes cannot be avoided, a slope change between two consecutive slopes
should not exceed:
— 1.5 per cent where the code number is 3 or 4; and
— 2 per cent where the code number is 1 or 2.
5.1.7 The transition from one slope to another should be accomplished by a curved surface with a rate
of change not exceeding:
— 0.1 per cent per 30 m (minimum radius of curvature of 30 000 m) where the code number is 4;
— 0.2 per cent per 30 m (minimum radius of curvature of 15 000 m) where the code number is 3; and
— 0.4 per cent per 30 m (minimum radius of curvature of 7 500 m) where the code number is 1 or 2.
Sight distance
5.1.8 Where slope changes cannot be avoided, they should be such that there will be an unobstructed
line of sight from:
Part 1. Runways
Chapter 5. Physical characteristics
5-3
— any point 3 m above a runway to all other points 3 m above the runway within a distance of at least
half the length of the runway where the code letter is C, D or E;
— any point 2 m above a runway to all other points 2 m above the runway within a distance of at least
half the length of the runway where the code letter is B; and
— any point 1.5 m above a runway to all other points 1.5 m above the runway within a distance of at
least half the length of the runway where the code letter is A.
5.1.9 Consideration will have to be given to providing an unobstructed line of sight over the entire
length of a single runway where a full-length parallel taxiway is not available. Where an aerodrome has
intersecting runways, additional criteria on the line of sight of the intersection area would need to be
considered for operational safety. A clear line of sight between the ends of intersecting runways is
recommended. Terrain needs to be graded and permanent objects need to be located so that there will be
an unobstructed line of sight, as stipulated in Annex 14, Volume I, 3.1.17, from any point to any
corresponding point above an intersecting runway centre line, within the runway visibility zone. The runway
visibility zone is an area formed by imaginary lines connecting the two runways’ visibility points, as shown in
Figure 5-1. The location of each runway’s visibility point is determined as follows:
a) If the distance from the intersection of two runway centre lines to a runway end is 250 m or less, the
visibility point is on the centre line of the runway end.
b) If the distance from the intersection of the two runway centre lines to a runway end is greater than
250 m but less than 500 m, the visibility point is on the centre line 250 m from the intersection of the
two runway centre lines.
c) If the distance from the intersection of the two runway centre lines to a runway end is equal to or
greater than 500 m, the visibility point is on the centre line midway between the runway end and the
intersection of the centre lines.
Distance between slope changes
5.1.10 Undulations or appreciable changes in slopes located close together along a runway should be
avoided. The distance between the points of intersection of two successive curves should not be less than:
a) the sum of the absolute numerical values of the corresponding slope changes multiplied by the
appropriate value as follows:
— 30 000 m where the code number is 4;
— 15 000 m where the code number is 3; and
— 5 000 m where the code number is 1 or 2; or
b) 45 m;
whichever is greater.
5.1.11 The following example illustrates how the distance between slope changes is to be determined
(see Figure 5-2):
5-4
Aerodrome Design Manual
A
a
x
d
b
225 m
1/2 D
B
D
1/2 C
When
A < 225 m
Runway visibility zone
B < 450 m
but > 225 m
C
C > 450 m
c
D > 450 m
Then
xa = Distance to
end of runway
xb = 225 m
xc = 1/2 C
xd = 1/2 D
Figure 5-1.
Runway visibility zone
Part 1. Runways
Chapter 5. Physical characteristics
5-5
Point of
intersection
e
z Slop
y Slope
pe
x Slo
D
Figure 5-2.
Point of
intersection
Profile on centre line of runway
D for a runway where the code number is 3 should be at least
15 000 [|x-y| + |y-z|] m
|x-y| being the absolute numerical value of x-y
|y-z| being the absolute numerical value of y-z
Assuming
then
x
y
z
|x-y|
=
=
=
=
+0.01
-0.005
+0.005
0.015
|y-z|
=
0.01
To comply with the specifications, D should be not less than:
15 000 (0.015 + 0.01) m,
that is, 15 000 × 0.025 = 375 m
Transverse slopes
5.1.12 To promote the most rapid drainage of water, the runway surface should, if practicable, be
cambered except where a single crossfall from high to low in the direction of the wind most frequently
associated with rain would ensure rapid drainage. The transverse slope should ideally be:
— 1.5 per cent where the code letter is C, D, E or F;
— 2 per cent where the code letter is A or B;
but in any event should not exceed 1.5 per cent or 2 per cent, as applicable, nor be less than 1 per cent
except at runway or taxiway intersections where flatter slopes may be necessary. For a cambered
surface the transverse slope on each side of the centre line should be symmetrical. On wet runways with
cross-wind conditions the problem of aquaplaning from poor drainage is apt to be accentuated.
5-6
Aerodrome Design Manual
5.1.13 The transverse slope should be substantially the same throughout the length of a runway
except at an intersection with another runway or a taxiway where an even transition should be provided
taking account of the need for adequate drainage. Additional guidance is given in the Aerodrome Design
Manual (Doc 9157), Part 3 — Pavements.
Combined slopes
5.1.14 When a runway is planned that will combine the extreme values for the longitudinal slopes and
changes in slope combined with extreme transverse slopes, a study should be made to ensure that the
resulting surface profile will not hamper the operation of aeroplanes.
Strength
5.1.15 A runway should be capable of withstanding the traffic of aeroplanes the runway is intended to
serve. For details of pavement design methods refer to the Aerodrome Design Manual, Part 3.
Surface
5.1.16 The surface of a runway shall be constructed without irregularities that would result in loss in
braking action or otherwise adversely affect the take-off or landing of an aeroplane. Surface irregularities
may adversely affect the take-off or landing of an aeroplane by causing excessive bouncing, pitching,
vibration or other difficulties in the control of an aeroplane. Additional guidance is included in the Aerodrome
Design Manual, Part 3.
5.1.17 In adopting tolerances for runway surface irregularities, the following standard of construction is
achievable for short distances of 3 m and conforms to good engineering practice:
Except across the crown of a camber or across drainage channels, the finished surface of the wearing
course is to be of such regularity that, when tested with a 3 m straight-edge placed anywhere in any
direction on the surface, there is no deviation greater than 3 mm between the bottom of the straightedge and the surface of the pavement anywhere along the straight- edge.
5.1.18
Caution should also be exercised when inserting runway lights or drainage grilles in runway
surfaces to ensure that adequate smoothness of the surface is maintained.
5.1.19 The operation of aircraft and differential settlement of surface foundations will eventually lead to
increases in surface irregularities. Small deviations in the above tolerances will not seriously hamper aircraft
operations. In general, isolated irregularities of the order of 2.5 cm to 3 cm over a 45 m distance are
tolerable. Exact guidance on the maximum acceptable irregularity cannot be given as it varies between
aircraft and, even for a certain type of aircraft, depends upon its mass, mass distribution, undercarriage
characteristics and speed. A sequence of wave-like runway surface irregularities, each separately being
considered acceptable, could potentially induce great dynamic loads on the aircraft undercarriage or severe
vibrations which could impair the readability of the cockpit instruments.
5.1.20 The dynamic loads on an aircraft during the landing or take-off run on an uneven runway
surface can be determined by measuring the actual response of an aircraft rolling over that surface. Tests by
one State have shown that use of a ground-run simulation model to determine the forces acting on an
aircraft undercarriage when rolling over an actually measured or planned surface profile results in a very
useful tool for objectively judging the quality of a runway or taxiway surface. With this method the effects of
Part 1. Runways
Chapter 5. Physical characteristics
5-7
modifications of the surface on aircraft response can be analysed before those modifications have been
carried out, thus eliminating many uncertainties about the results, and the modifications to be proposed can
be assessed from a cost-benefit point of view. In the simulation model, acceptability of surface unevenness
is related to the loads acting on the undercarriage of the aircraft which are considered critical for this
purpose.
5.1.21 Deformation of the runway with time may also increase the possibility of the formation of water
pools. Pools as shallow as approximately 3 mm in depth, particularly if they are located where they are likely
to be encountered at high speed by landing aeroplanes, can induce aquaplaning which can then be
sustained on a wet runway by a much shallower depth of water. It is, of course, especially necessary to
prevent pools from forming whenever there is a possibility that they might become frozen.
Surface texture
5.1.22 The surface of a paved runway shall be so constructed as to provide good friction
characteristics when the runway is wet. Evaluation and operational experience have shown that properly
engineered and maintained asphaltic or portland cement concrete surfaces meet these criteria. This does
not preclude the use of other materials which meet these criteria.
5.1.23 Measurements of the friction characteristics of a new or resurfaced runway should be made with a
continuous friction measuring device using self-wetting features in order to assure that the design objectives
with respect to its friction characteristics have been achieved. Guidance on friction characteristics of new
runway surfaces is given in Attachment A, Section 7, of Annex 14, Volume I. Additional guidance is included
in the Airport Services Manual (Doc 9137), Part 2 — Pavement Surface Conditions.
5.1.24 The average surface texture depth of a new surface should be not less than 1.0 mm. This
normally requires some form of special surface treatment. The grease and sand patch methods as
described in the Airport Services Manual, Part 2, are two methods currently used for measuring surface
texture.
5.1.25 When the surface is grooved or scored, the grooves or scorings should be either perpendicular
to the runway centre line or parallel to non-perpendicular transverse joints, where applicable. Guidance on
methods for improving the runway surface texture is given in the Aerodrome Design Manual, Part 3 —,
Pavements.
5.2
RUNWAY SHOULDERS
General
5.2.1 Runway shoulders must be provided to ensure a transition from the full strength pavement to the
unpaved strip of the runway. The paved shoulders protect the edge of the runway pavement, contribute to
the prevention of soil erosion by jet blast and mitigate foreign object damage to jet engines. Where the soil is
susceptible to erosion, the width of the shoulders may be increased beyond the minimum values
recommended in 5.2.8, after taking into account the exhaust velocity contours of the most demanding
aircraft.
5-8
Aerodrome Design Manual
5.2.2 Runway shoulders should be provided for a runway where the code letter is D or E, and the
runway width is less than 60 m. Runway shoulders should be provided where the code letter is F.
5.2.3 The shoulder of a runway or stopway should be prepared or constructed so as to minimize any
hazard to an aeroplane running off the runway or stopway. Some guidance is given in the following
paragraphs on certain special problems which may arise, and on the further question of measures to avoid
the ingestion of loose stones or other objects by turbine engines.
5.2.4 In some cases, the bearing strength of the natural ground in the strip may be sufficient, without
special preparation, to meet the requirements for shoulders. Where special preparation is necessary, the
method used will depend on local soil conditions and the mass of the aeroplanes the runway is intended to
serve. Soil tests will help in determining the best method of improvement (e.g. drainage, stabilization,
surfacing, light paving). However, it would be prudent to provide shoulders of appropriate strength to meet
the requirements specified in 5.2.1 and to preclude possible structural damage to an aircraft veering off the
main runway pavement.
5.2.5 When designing shoulders, prevention of the ingestion of stones or other objects by turbine
engines should be an important consideration. The rate of damage caused to engines from ingesting foreign
objects is substantial and, therefore, a matter of continuing concern. With new larger aeroplanes equipped
with more powerful engines, the problem is likely to be aggravated. Protection of the runway shoulders is
therefore needed. Similarly, it should be ascertained whether the planned type of surface of the shoulder will
be adequate to resist erosion from engine blast.
5.2.6 Where shoulders have been treated specially, either to provide the required bearing strength or
to prevent the presence of stones or debris, difficulties may arise because of a lack of visual contrast
between the runway surface and that of the adjacent strip. This difficulty can be overcome either by
providing a good visual contrast in the surfacing of the runway or strip, or by providing a runway side stripe
marking.
5.2.7 At airports subjected to snow and ice conditions, the problem caused by foreign object damage
is particularly critical on the entire movement area. The extent to which snow/ice clearance is carried out will
determine the risk level not only for foreign object damage but likewise for run-offs.
5.2.8 The runway shoulders should extend symmetrically on each side of the runway so that the
overall width of the runway and its shoulders is not less than 60 m for code letter E and 75 m for code
letter F.
Slopes
5.2.9 The surface of the shoulder that abuts the runway should be flush with the surface of the runway
and its transverse downward slope should not exceed 2.5 per cent.
Strength
5.2.10 A runway shoulder should be prepared or constructed so as to be capable, in the event of an
aeroplane running off the runway, of supporting the aeroplane without inducing structural damage to the
aeroplane and of supporting ground vehicles which may operate on the shoulder.
Part 1. Runways
Chapter 5. Physical characteristics
5-9
5.3
RUNWAY STRIPS
Purpose of a runway strip
5.3.1 A runway strip extends laterally to a specified distance from the runway centre line, longitudinally
before the threshold, and beyond the runway end. It provides an area clear of objects which may endanger
aeroplanes. The strip includes a graded portion which should be so prepared as to not cause the collapse of
the nose gear if an aircraft should leave the runway. There are certain limitations on the slopes permissible
on the graded portion of the strip. The runway strip is also required to protect ILS/MLS sensitive/critical
areas. Within the strip, there is an object-free area. Any equipment or installation, required for air navigation
purposes, located in this object-free area, should be frangible and mounted as low as possible. A runway
and any associated stopways are included in a strip.
Length
5.3.2 A strip should extend before the threshold and beyond the end of the runway or stopway for a
distance of at least:
— 60 m where the code number is 2, 3 or 4;
— 60 m where the code number is 1 and the runway is an instrument one; and
— 30 m where the code number is 1 and the runway is a non-instrument one.
Width
5.3.3 A strip including a precision approach runway shall, wherever practicable, extend laterally for a
distance of at least:
— 150 m where the code number is 3 or 4; and
— 75 m where the code number is 1 or 2;
on each side of the centre line of the runway and its extended centre line throughout the length of the strip.
5.3.4
least:
A strip including a non-precision approach runway should extend laterally to a distance of at
— 150 m where the code number is 3 or 4; and
— 75 m where the code number is 1 or 2;
on each side of the centre line of the runway and its extended centre line throughout the length of the strip.
5.3.5 A strip including a non-instrument runway should extend, on each side of the centre line of the
runway and its extended centre line throughout the length of the strip, for a distance of at least:
— 75 m where the code number is 3 or 4;
5-10
Aerodrome Design Manual
— 40 m where the code number is 2; and
— 30 m where the code number is 1.
Objects
5.3.6 An object, other than equipment or installation required for air navigation purposes, situated on a
runway strip which may endanger aeroplanes should be regarded as as an obstacle and should, as far as
practicable, be removed. Any equipment or installation required for air navigation purposes which must be
located on the runway strip should be of minimum practicable mass and height, frangibly designed and
mounted, and sited in such a manner as to reduce the hazard to aircraft to a minimum.
5.3.7 No fixed object, other than visual aids required for air navigation purposes, shall be permitted on
a runway strip:
a) within 77.5 m of the runway centre line of a precision approach runway category I, II or III where the
code number is 3 or 4 and the code letter is F; or
b) within 60 m of the runway centre line of a precision approach runway category I, II or III where the
code number is 3 or 4; or
c) within 45 m of the runway centre line of a precision approach runway category I where the code
number is 1 or 2.
5.3.8 Visual aids required for air navigation which must be located on this part of the strip shall be of
minimum practicable mass and height, frangibly designed and mounted, and sited in such a manner as to
reduce the hazard to aircraft to a minimum. No mobile object shall be permitted on this part of the runway
strip during the use of the runway for landing or take-off.
5.3.9 Within the general area of the strip adjacent to the runway, measures should be taken to prevent
an aeroplane’s wheel, when sinking into the ground, from striking a hard vertical face as significant damage
to the aircraft landing gear may result. Special problems may arise as the result of runway light fittings or
other objects mounted in the strip or at the intersection with a taxiway or another runway. In the case of
construction, such as runways or taxiways, where the surface must also be flush with the strip surface, a
vertical face can be eliminated by chamfering from the top of the construction to not less than 30 cm below
the strip surface level. Other objects, the functions of which do not require them to be at surface level,
should be buried to a depth of not less than 30 cm.
Grading
5.3.10
That portion of a strip of an instrument runway within a distance of at least:
— 75 m where the code number is 3 or 4; and
— 40 m where the code number is 1 or 2;
from the centre line of the runway and its extended centre line should provide a graded area for aeroplanes
which the runway is intended to serve in the event of an aeroplane running off the runway.
Part 1. Runways
Chapter 5. Physical characteristics
5-11
5.3.11 For a precision approach runway it may be desirable to adopt a greater width where the code
number is 3 or 4. Figure 5-3 shows the shape and dimensions of a wider strip that may be considered for
such a runway. This strip has been designed using information on aircraft running off runways. The portion
to be graded extends to a distance of 105 m from the centre line, except that the distance is gradually
reduced to 75 m from the centre line at both ends of the strip, for a length of 150 m from the runway end.
5.3.12
That portion of a strip of a non-instrument runway within a distance of at least:
— 75 m where the code number is 3 or 4;
— 40 m where the code number is 2; and
— 30 m where the code number is 1;
from the centre line of the runway and its extended centre line should provide a graded area for aeroplanes
which the runway is intended to serve in the event of an aeroplane running off the runway.
5.3.13 The surface of that portion of a strip that abuts a runway, shoulder or stopway shall be flush
with the surface of the runway, shoulder or stopway.
5.3.14 That portion of a strip to at least 30 m before a threshold should be prepared against blast
erosion in order to protect a landing aeroplane from the danger of an exposed edge.
Longitudinal slopes
5.3.15
A longitudinal slope along that portion of a strip to be graded should not exceed:
— 1.5 per cent where the code number is 4;
— 1.75 per cent where the code number is 3; and
— 2 per cent where the code number is 1 or 2.
300 m
300 m
150 m
150 m
Runway
75 m
75 m
105 m
105 m
Figure 5-3. Graded portion of a strip including a precision
approach runway where the code number is 3 or 4
5-12
Aerodrome Design Manual
Longitudinal slope changes
5.3.16 Slope changes on that portion of a strip to be graded should be as gradual as practicable and
abrupt changes or sudden reversals of slopes avoided.
5.3.17 In order to accommodate aeroplanes making auto-coupled approaches and automatic landings
(irrespective of weather conditions) it is desirable that slope changes before the threshold of a precision
approach runway be avoided or kept to a minimum on that portion of the strip within a distance of at least
30 m on each side of the extended centre line of the runway. This is desirable because these aeroplanes
are equipped with a radio altimeter for final height and flare guidance, and when the aeroplane is above the
terrain immediately prior to the threshold, the radio altimeter will begin to provide information to the
automatic pilot for auto-flare. Where slope changes cannot be avoided on this portion, the rate of change
between two consecutive slopes should not exceed 2 per cent per 30 m.
Transverse slopes
5.3.18 Transverse slopes on that portion of a strip to be graded should be adequate to prevent the
accumulation of water on the surface but should not exceed:
— 2.5 per cent where the code number is 3 or 4; and
— 3 per cent where the code number is 1 or 2;
except that to facilitate drainage the slope for the first 3 m outward from the runway, shoulder or stopway
edge should be negative as measured in the direction away from the runway and may be as great as 5 per
cent.
5.3.19 The transverse slopes of any portion of a strip beyond that to be graded should not exceed an
upward or downward slope of 5 per cent as measured in the direction away from the runway.
Strength
5.3.20
That portion of a strip of an instrument runway within a distance of at least:
— 75 m where the code number is 3 or 4; and
— 40 m where the code number is 1 or 2;
from the centre line of the runway and its extended centre line should be so prepared or constructed as to
minimize hazards arising from differences in load-bearing capacity to aeroplanes which the runway is
intended to serve in the event of an aeroplane running off the runway.
5.3.21
That portion of a strip containing a non-instrument runway within a distance of at least:
— 75 m where the code number is 3 or 4;
— 40 m where the code number is 2; and
— 30 m where the code number is 1;
Part 1. Runways
Chapter 5. Physical characteristics
5-13
from the centre line of the runway and its extended centre line should be so prepared or constructed as to
minimize hazards arising from differences in load-bearing capacity to aeroplanes which the runway is
intended to serve in the event of an aeroplane running off the runway.
5.3.22 Since the graded portion of a strip is provided to minimize the hazard to an aircraft running off
the runway, it should be graded in such a manner as to prevent the collapse of the nose landing gear of the
aircraft. The surface should be prepared in such a manner as to provide drag to an aircraft and below the
surface, it should have sufficient bearing strength to avoid damage to the aircraft. To meet these divergent
needs, the following guidelines are provided for preparing the strip. Aircraft manufacturers consider that a
depth of 15 cm is the maximum depth to which the nose gear may sink without collapsing. Therefore, it is
recommended that the soil at a depth of 15 cm below the finished strip surface be prepared to have a
bearing strength of California Bearing Ratio (CBR) value of 15 to 20. The intention of this underlying
prepared surface is to prevent the nose gear from sinking more than 15 cm. The top 15 cm may be of lesser
strength which would facilitate deceleration of aircraft.
5.4
RUNWAY END SAFETY AREAS
Purpose of a RESA
5.4.1 ICAO Aircraft Accident/Incident Data Reports (ADREP) have indicated that aircraft
undershooting or overrunning the runway during landings or take-offs suffer significant damage. To minimize
such damage, it is considered necessary to provide an additional area beyond the ends of the runway strip.
These areas, known as Runway End Safety Areas, should be capable of adequately supporting any aircraft
which overruns or undershoots the runway and should be clear of all equipment and installations which are
not frangible.
5.4.2
A runway end safety area is required to be provided at each end of a runway strip where:
— the code number is 3 or 4; and
— the code number is 1 or 2 and the runway is an instrument one.
Length
5.4.3 A runway end safety area is required to extend from the end of a runway strip for as great a
distance as practicable, but at least 90 m.
5.4.4 A runway end safety area should, as far as practicable, extend from the end of the runway strip
to a distance of at least:
— 240 m where the code number is 3 or 4:
— 120 m where the code number is 1 or 2.
5.4.5 When deciding the length to be provided, consideration should be given to providing an area
long enough to contain overruns and undershoots resulting from a reasonably probable continuation of
adverse operational factors. On a precision approach runway, the ILS localizer is normally the first
5-14
Aerodrome Design Manual
upstanding obstacle, and the runway end safety area should extend up to this facility. In other circumstances
and on a non-precision approach or non-instrument runway, the first upstanding obstacle may be a road, a
railroad or other manmade or natural feature. In such circumstances, the runway end safety area should
extend as far as the obstacle.
Width
5.4.6
runway.
The width of a runway end safety area is required to be at least twice that of the associated
Objects
5.4.7 An object, other than equipment or an installation required for air navigation purposes, situated
on a runway end safety area which may endanger aeroplanes should be regarded as an obstacle and
should, as far as practicable, be removed. Any equipment or installation required for air navigation purposes
which must be located on the runway end safety area is required to be frangible, mounted as low as
possible and sited in such a manner as to reduce the hazard to aircraft to a minimum.
Clearing and grading
5.4.8 A runway end safety area should provide a cleared and graded area for aeroplanes which the
runway is intended to serve in the event of an aeroplane undershooting or overrunning the runway. The
surface of the ground in the runway end safety area does not need to be prepared to the same quality as the
runway strip.
Combined slopes
5.4.9 The slopes of a runway end safety area should be such that no part of the runway end safety
area penetrates the approach or take-off climb surface.
Longitudinal slopes
5.4.10 The longitudinal slopes of a runway end safety area should not exceed a downward slope of
5 per cent. Longitudinal slope changes should be as gradual as practicable and abrupt changes or sudden
reversals of slopes avoided.
5.4.11 In order to accommodate aeroplanes making auto-coupled approaches and automatic landings
(irrespective of weather conditions) it is desirable that slope changes be avoided or kept to a minimum on an
area symmetrical about the extended runway centre line approximately 60 m wide, and 300 m long before
the threshold of a precision approach runway. This is desirable because these aeroplanes are equipped with
a radio altimeter for final height and flare guidance, and when the aeroplane is above the terrain immediately
prior to the threshold, the radio altimeter will begin to provide information to the automatic pilot for auto-flare.
Where slope changes cannot be avoided, the rate of change between two consecutive slopes should not
exceed 2 per cent per 30 m.
Part 1. Runways
Chapter 5. Physical characteristics
5-15
Transverse slopes
5.4.12 The transverse slopes of a runway end safety area should not exceed an upward or downward
slope of 5 per cent. Transitions between differing slopes should be as gradual as practicable.
Strength
5.4.13 A runway end safety area should be so prepared or constructed as to reduce the risk of
damage to an aeroplane undershooting or overrunning the runway, enhance aeroplane deceleration, and
facilitate the movement of rescue and fire fighting vehicles. See 5.3.22 for guidance on the minimum
strength of the runway end safety area.
5.5
CLEARWAYS
Location
5.5.1
The origin of a clearway should be at the end of the take-off run available.
Length
5.5.2
The length of a clearway should not exceed half the length of the take-off run available.
Width
5.5.3 A clearway should extend laterally to a distance of at least 75 m on each side of the extended
centre line of the runway.
Slopes
5.5.4 The ground in a clearway should not project above a plane having an upward slope of 1.25 per
cent, the lower limit of this plane being a horizontal line which:
a) is perpendicular to the vertical plane containing the runway centre line; and
b) passes through a point located on the runway centre line at the end of the take-off run available.
5.5.5 Because of transverse or longitudinal slopes on a runway, shoulder or strip, in certain cases the
lower limit of the clearway plane specified above may be below the corresponding elevation of the runway,
shoulder or strip. It is not intended that these surfaces be graded to conform with the lower limit of the
clearway plane nor is it intended that terrain or objects which are above the clearway plane beyond the end
of the strip but below the level of the strip be removed unless it is considered they may endanger aeroplanes.
5.5.6 Abrupt upward changes in slope should be avoided when the slope on the ground in a clearway
is relatively small or when the mean slope is upward. In such situations, in that portion of the clearway within
5-16
Aerodrome Design Manual
a distance of 22.5 m on each side of the extended centre line, the slopes, slope changes and the transition
from runway to clearway should generally conform with those of the runway with which the clearway is
associated.
Objects
5.5.7 An object situated on a clearway which may endanger aeroplanes in the air should be regarded
as an obstacle and should be removed. Any equipment or installation required for air navigation purposes
which must be located on the clearway should be of minimum mass and height, frangibly designed and
mounted, and sited in such a manner as to reduce the hazard to aircraft to a minimum.
5.6
STOPWAYS
Width
5.6.1
A stopway shall have the same width as the runway with which it is associated.
Slopes
5.6.2 Slopes and changes in slope on a stopway, and the transition from a runway to a stopway
should comply with the specifications of 5.1.2 to 5.1.9 for the runway with which the stopway is associated
except that:
a) the limitation in 5.1.3 of a 0.8 per cent slope for the first and last quarter of the length of a runway
need not be applied to the stopway; and
b) at the junction of the stopway and runway and along the stopway the maximum rate of slope change
may be 0.3 per cent per 30 m (minimum radius of curvature of 10 000 m) for a runway where the
code number is 3 or 4.
Strength
5.6.3 A stopway should be prepared or constructed so as to be capable, in the event of an abandoned
take-off, of supporting the aeroplane which the stopway is intended to serve without inducing structural
damage to the aeroplane.
Surface
5.6.4 The surface of a paved stopway should be so constructed as to provide a good coefficient of
friction, compatible with that of the associated runway, when the stopway is wet.
5.6.5 The friction characteristics of an unpaved stopway should not be substantially less than that of
the runway with which the stopway is associated.
___________________
Chapter 6
PLANNING TO ACCOMMODATE FUTURE
AIRCRAFT DEVELOPMENTS
6.1
GENERAL
6.1.1 Annex 14, Volume I, sets forth the minimum aerodrome specifications for aircraft which have the
characteristics of those which are currently operating or for similar aircraft that are planned for introduction.
The current specifications are therefore intended to accommodate aeroplanes up to the size of the Airbus
A380-800. Accordingly, any additional safeguards that might be considered appropriate to provide for more
demanding aircraft are not taken into account in the Annex. Such matters are left to appropriate authorities
to evaluate and take into account as necessary for each particular aerodrome.
6.1.2 The information in the following paragraphs may assist in increasing the awareness of these
authorities and airport planners of the way in which some of the specifications may alter with the introduction
of larger aircraft. In this respect it is worth noting that it is probable that some increase in current maximum
aircraft size will be acceptable without major modifications to existing aerodromes. However, the upper limit
of aircraft size which is examined below is, in all probability, beyond this consideration unless aerodrome
procedures are altered, with resulting reduction in aerodrome capacity.
6.2
FUTURE AIRCRAFT TRENDS
6.2.1 The trends for future aircraft designs may be obtained from various sources, including the aircraft
manufacturers and the International Coordinating Council of Aerospace Industries Associations. For the
purpose of planning future airport development, the following aircraft dimensions may be used:
wing span
outer main gear wheel span
overall length
tail height
maximum gross mass
up to 84 m
up to 20 m
80 m or more
up to 24 m
583 000 kg or more.
6.3
AERODROME DATA
6.3.1 The trend toward longer take-off distances for larger aircraft take-off masses is considered to
have levelled off, and greater runway lengths than are currently available at major aerodromes should not be
required.
6.3.2 Using the rationale developed for implementation of the Annex 14, Volume I, aerodrome
reference code, it is possible that aircraft with larger outer main gear wheel spans could have the following
effects on the runway system.
6-1
6-2
Aerodrome Design Manual
6.3.3
WR
where
TM
and C
Runway width may be represented by the expression:
=
TM + 2C
=
=
outer main gear wheel span
clearance between the outer main gear wheel and the runway edge.
This geometry is shown in Figure 6-1.
6.3.4 Using the present value of C, a B747 on a runway of 45 m width and the increased main gear
wheel span of 20 m would indicate a runway width of 52 m. However, other factors which are not included in
this rationale indicate that it might be advisable, for planning purposes, to consider a width of up to 60 m. For
code F aircraft, (see Table 1-1) a runway width of 60 m with 7.5 m shoulders is recommended.
CL
TM
C
C
WR
Figure 6-1.
Runway width geometry
___________________
Appendix 1
AEROPLANE CLASSIFICATION BY CODE NUMBER
AND LETTER
Code
Aeroplane
reference
field length
(m)
DHC2
1A
DHC2T
Britten Norman
Cessna
(m)
Outer
main gear
wheel span
(m)
381
14.6
3.3
1A
427
14.6
3.3
BN2A
1A
353
14.9
4.0
152
1A
408
10.0
—
172 S
1A
381
11.0
2.7
180
1A
367
10.9
—
182 S
1A
462
11.0
2.9
Stationair 6
1A
543
11.0
2.9
Turbo 6
1A
500
11.0
2.9
Stationair 7
1A
600
10.9
—
Turbo 7
1A
567
10.9
—
Skylane
1A
479
10.9
—
Turbo Skylane
1A
470
10.9
—
310
1A
518
11.3
—
310 Turbo
1A
507
11.3
—
Golden Eagle 421 C
1A
708
12.5
—
Titan 404
1A
721
14.1
—
1A
2
10.7
3.2
2
10.8
3.2
2
10.8
3.4
2
11.0
3.5
2
11.0
3.5
2
11.9
3.5
2
11.8
3.2
2
Aircraft Make
DeHavilland Canada
Piper
Model
PA28-161
PA28-181
1A
PA28R-201
1A
PA32R-301
1A
PA32R-301T
1A
PA34-220T
1A
PA44-180
Raytheon/Beechcraft
1A
494
490
487
539
756
520
671
Wing span
PA46-350P
1A
637
13.1
3.9
A24R
1A
603
10.0
3.9
A36
1A
670
10.2
2.9
A1-1
A1-2
Aerodrome Design Manual
Code
Aeroplane
reference
field length
(m)
76
1A
B55
(m)
Outer
main gear
wheel span
(m)
430
11.6
3.3
1A
457
11.5
2.9
B60
1A
793
12.0
3.4
B100
1A
579
14.0
4.3
Cessna
525
1B
939
14.3
4.1
DeHavilland Canada
DHC3
1B
497
17.7
3.7
DHC6
1B
695
19.8
4.1
LET
L410 UPV
1B
740
19.5
4.0
Pilatus
PC-12
1B
452
16.2
4.5
Raytheon/Beechcraft
E18S
1B
753
15.0
3.9
B80
1B
427
15.3
4.3
C90
1B
488
15.3
4.3
200
1B
579
16.6
5.6
Short
SC7-3/SC7-3A
1B
616
19.8
4.6
DeHavilland Canada
DHC7
1C
689
28.4
7.8
Lear Jet
24F
2A
1 005
10.9
2.5
28/29
2A
912
13.4
2.5
L410 UPV-E
2B
920
20.0
1
4.0
1
4.0
1
4.0
1
Aircraft Make
LET
Model
L410 UPV-E9
L410 UPV-E20
2B
2B
952
1 050
Wing span
20.0
20.0
L420
2B
920
20.0
4.0
Shorts
SD3-30
2B
1 106
22.8
4.6
Dassault Aviation
Falcon 10
3A
1 615
13.1
3.0
Hawker Siddley
HS 125-400
3A
1 646
14.3
3.3
HS 125-600
3A
1 646
14.3
3.3
HS 125-700
3A
1 768
14.3
3.3
24D
3A
1 200
10.9
2.5
35A/36A
3A
1 287/1 458
12.0
2.5
54
3A
1 217
13.4
2.5
55
3A
1 292
13.4
2.5
Lear Jet
Part 1. Runways
Appendix 1. Aeroplane classification by code number and letter
A1-3
Code
Aeroplane
reference
field length
(m)
CRJ 100
3B
CRJ 100ER
(m)
Outer
main gear
wheel span
(m)
1 470
21.2
4.0
3B
1 720
21.2
4.0
CRJ 200
3B
1 440
21.2
4.0
CRJ 200ER
3B
1 700
21.2
4.0
Falcon 20
3B
1 463
16.3
3.7
Falcon 200
3B
1 700
16.3
3.5
F50/F50EX
3B
1 586
18.9
4.5
Falcon 900
3B
1 504
19.3
4.6
Falcon 900EX
3B
1 590
19.3
4.6
F2000
3B
1 658
19.3
5.0
Embraer
EMB-135 LR
3B
1 745
20.0
4.1
Fokker
F28-1000
3B
1 646
23.6
5.8
F28-2000
3B
1 646
23.6
5.8
SPX
3B
1 644
16.6
—
Galaxy
3B
1 798
17.7
—
Gulfstream Aero.
G IV-SP
3B
1 661
23.7
4.8
Nord
262
3B
1 260
21.9
3.4
Antonov
AN24
3C
1 600
29.2
8.8
Boeing
B717-200
3C
1 670
28.4
5.4
B737-600
3C
1 690
34.3
7.0
B737-700
3C
1 598
34.3
7.0
240
3C
1 301
28.0
8.4
440
3C
1 564
32.1
8.6
580
3C
1 341
32.1
8.6
600
3C
1 378
28.0
8.4
640
3C
1 570
32.1
8.6
DC3
3C
1 204
28.8
5.8
DC4
3C
1 542
35.8
8.5
DC6A/6B
3C
1 375
35.8
8.5
DC9-20
3C
1 551
28.5
6.0
Embraer
EMB-120 ER
3C
1 481
19.8
6.6
Fokker
F27-500
3C
1 670
29.0
7.9
F27-600
3C
1 670
29.0
7.9
F28-3000
3C
1 640
25.1
5.8
Aircraft Make
Bombardier Aero.
Dassault Aviation
I.A.I.
Convair
Douglas
Model
Wing span
A1-4
Aerodrome Design Manual
Code
Aeroplane
reference
field length
(m)
F28-4000
3C
F28-6000
(m)
Outer
main gear
wheel span
(m)
1 640
25.1
5.8
3C
1 400
25.1
5.8
F50
3C
1 355
29.0
8.0
McDonnell Douglas
MD90
3C
1 798
32.9
6.2
SAAB
340A
3C
1 220
21.4
7.3
3
Aircraft Make
Model
Wing span
340B
3C
1 220
22.8
7.3
SAAB 2000
3C
1 340
24.8
8.9
BAe
ATP
3D
1 540
30.6
9.3
DeHavilland Canada
DHC5D
3D
1 471
29.3
10.2
Airbus
A300 B2
3D
1 676
44.8
10.9
Bombardier Aero.
CRJ 100LR
4B
1 880
21.2
4.0
CRJ 200LR
4B
1 850
21.2
4.0
Dassault Aviation
Falcon 20-5 (Retrofit)
4B
1 859
16.3
3.7
Embraer
EMB-145 LR
4B
2 269
20.0
4.1
Airbus
A320-200
4C
2 480
33.9
8.7
BAC
1-11-200
4C
1 884
27.0
5.2
1-11-300
4C
2 484
27.0
5.2
1-11-400
4C
2 420
27.0
5.2
1-11-475
4C
2 286
28.5
5.4
1-11-500
4C
2 408
28.5
5.2
B727-100
4C
2 502
32.9
6.9
B727-200
4C
3 176
32.9
6.9
B737-100
4C
2 499
28.4
6.4
B737-200
4C
2 295
28.4
6.4
B737-300
4C
2 160
28.9
6.4
B737-400
4C
2 550
28.9
6.4
B737-500
4C
2 470
28.9
6.4
B737-800
4C
2 090
34.3
7.0
B737-900
4C
2 240
34.3
7.0
Fokker
F100
4C
1 840
28.1
6.0
Gulfstream Aero
GV
4C
1 863
28.5
5.1
Douglas
DC9-10
4C
1 975
27.2
5.9
DC9-15
4C
1 990
27.3
6.0
Boeing
Part 1. Runways
Appendix 1. Aeroplane classification by code number and letter
A1-5
Code
Aeroplane
reference
field length
(m)
DC9-20
4C
DC9-30
(m)
Outer
main gear
wheel span
(m)
1 560
28.4
6.0
4C
2 134
28.5
5.9
DC9-40
4C
2 091
28.5
5.9
DC9-50
4C
2 451
28.5
5.9
MD81
4C
2 290
32.9
6.2
MD82
4C
2 280
32.9
6.2
MD83
4C
2 470
32.9
6.2
MD87
4C
2 260
32.9
6.2
MD88
4C
2 470
32.9
6.2
A300 B4
4D
2 605
44.8
10.9
A300-600
4D
2 332
44.8
10.9
A310
4D
1 845
44.8
10.9
B707-300
4D
3 088
44.4
7.9
B707-400
4D
3 277
44.4
7.9
B720
4D
1 981
39.9
7.5
B757-200
4D
1 980
38. 1
8.6
B757-300
4D
2 400
38.1
8.6
B767-200
4D
1 981
47.6
10.8
B767-300ER
4D
2 540
47.6
10.9
B767-400ER
4D
3 130
51.9
10.8
Canadair
CL44D-4
4D
2 240
43.4
10.5
Ilyushin
18V
4D
1 980
37.4
9.9
62M
4D
3 280
43.2
8.0
L100-20
4D
1 829
40.8
4.9
L100-30
4D
1 829
40.4
4.9
L188
4D
2 066
30.2
10.5
L1011-1
4D
2 426
47.3
12.8
L1011-100/200
4D
2 469
47.3
12.8
L1011-500
4D
2 844
47.3
12.8
DC8-61
4D
3 048
43.4
7.5
DC8-62
4D
3 100
45.2
7.6
DC8-63
4D
3 179
45.2
7.6
DC8-71
4D
2 770
43.4
7.5
DC8-72
4D
2 980
45.2
7.6
Aircraft Make
McDonnell Douglas
Airbus
Boeing
Lockheed
Douglas
Model
Wing span
A1-6
Aerodrome Design Manual
Code
Aeroplane
reference
field length
(m)
DC8-73
4D
DC10-10
(m)
Outer
main gear
wheel span
(m)
3 050
45.2
7.6
4D
3 200
47.4
12.6
DC10-30
4D
3 170
50.4
12.6
DC10-40
4D
3 124
50.4
12.6
TU134A
4D
2 400
29.0
10.3
TU154
4D
2 160
37.6
12.4
B747-100
4E
3 060
59.6
12.4
B747-200
4E
3 150
59.6
12.4
B747-300
4E
3 292
59.6
12.4
4
Aircraft Make
McDonnell Douglas
Tupolev
Boeing
Model
Wing span
B747-400
4E
2 890
64.9
12. 6
B747-SR
4E
1 860
59.6
12.4
B747-SP
4E
2 710
59.6
12.4
B777-200
4E
2 390
61.0
12.9
B777-200ER
4E
3 110
61.0
12.9
B777-300
4E
3 140
60.9
12.9
B777-300ER
4E
3 120
64.8
12.9
4
McDonnell Douglas
MD11
4E
3 130
52.0
12. 6
Airbus
A380
4F
3 350
79.8
14.3
1.
2.
3.
4.
With wing tip tanks installed.
Over a 15m obstacle.
With extended wing tips.
Winglets
___________________
Appendix 2
THE EFFECT OF VARIABLE RUNWAY SLOPES ON
TAKE-OFF RUNWAY LENGTHS
1.
INTRODUCTION
1.1 A study was done by the University of California, sponsored by ICAO, into the effect of variable
runway slopes on take-off runway lengths. This Appendix provides a brief summary of the scope and
findings of that study.
1.2
The purpose of the study was to:
a) determine the effect of nonuniform slopes on runway lengths for a representative group of piston
and jet transport aeroplanes;
b) examine the methods used to correct for slope; and
c) develop a correction method that best reflects the effects of non- uniform slopes.
2.
AIRCRAFT SELECTED FOR STUDY
2.1 The following aircraft were selected for analysis as being representative of transport types being
flown in civil aviation: DC-6B, Vanguard, DC-8 and DC-9. These aircraft encompass piston-engined
propeller, turboprop, turbojet and turbofan types, respectively.
3.
ASSUMPTIONS MADE FOR STUDY PURPOSES
Aerodrome elevation
3.1 Flight operation aeroplane manuals relate runway length to pressure altitude rather than to
geographic elevation. Throughout the study it was assumed that the two were equivalent.
Aerodrome temperature
3.2 The temperatures used in the study were standard temperatures at the selected elevations of sea
level and 300 m, and a hot day temperature of 32°C was used at both elevations.
A2-1
A2-2
Aerodrome Design Manual
Wind
3.3
Calm conditions were assumed to prevail on the surface of the runway.
Runway surface conditions
3.4 Runway surface irregularities and a low runway coefficient of friction were not accounted for in the
study. Dry runway conditions were assumed to prevail.
Runway longitudinal slope
3.5 In considering runway longitudinal profiles to be analysed, the constraints detailed in Annex 14 at
that time, i.e. the Fourth Edition, were adhered to. These were:
a) the slope computed by dividing the difference between the maximum and minimum elevation along
the runway centre line by the runway length should not exceed 1 per cent;
b) along no portion of a runway should the longitudinal slope exceed: 1.25 per cent where the runway
*
basic length is 1 800 m or above; 1.5 per cent where the runway basic length is up to but not
including 1 800 m;
c) a slope change between two consecutive slopes should not exceed 1.5 per cent;
d) the slope should not exceed 0.8 per cent for the first and last quarter of the length of the runway, for
runways 1 800 m or above;
e) where slope changes cannot be avoided, they should be such that there will be an unobstructed line
of sight from any point 3 m above the runway to all other points 3 m above the runway within a
distance of at least half the length of the runway;
f)
the transition from one slope to another should be accomplished by a curved surface with a rate of
change not exceeding:
— 0.1 per cent per 30 m where the runway basic length is 1 800 m or above;
— 0.2 per cent per 30 m where the runway basic length is up to but not including 1 800 m.
Vertical curves were not used in the study profiles since their effect on runway length was considered to be
negligible.
3.6 With these constraints, several study profiles were developed as shown in Figure A2-1. The
profiles were grouped into four general types designated as “A”, “B”, “C” and “D”. Type “A” profiles consist of
uphill slopes; Type “B” downhill slopes; Type “C” convex profiles (uphill-downhill); and Type “D” concave
profiles (downhill-uphill). The majority of the profiles shown in Figure A-1 are Type “A” (uphill) with the slopes
on the first and last quarter limited to 0.8 per cent.
*
Former aerodrome reference code in Annex 14 was based on the runway basic length, which was defined as the runway length
selected for aerodrome planning purposes which is required for take-off or landing under standard atmospheric conditions for zero
elevation, zero wind and zero runway slopes.
31/8/06
Corr.
Part 1. Runways
Appendix 2. The effect of variable runway slopes on take-off runway lengths
Profile
number
Take-off
L/4
L/4
L/4
L/4
Profile
number
L
A– 3
A– 4
5
+ 1.2
A– 7
L/4
L
+ 0.75
A– 8
+ 0.50
+ 0.80
0
+ 0.35 + 0.8
5
+ 1.2
0
+ 1.2
0.00
+ 0.80
0.00
0.00
+ 0.40
+ 0.80
+ 1 .2 0
A – 10
A – 11
+ 0.75
+ 1.20
A– 9
+ 0.40
A – 12
+ 0.80
A – 13
0.00
5
+ 1.2
0.00
0.00
0.00
0
+ 0.8
L/4
L/4
L/4
0.00
Profile
number
Take-off
L/2
L/2
C–1
+ .75
– .75
C–2
+ .60
– .90
C–3
+ .90
– .60
– 0.80
D–1
– .75
+ .75
– 0.80
D–2
– .90
+ .60
D–3
– .60
+ .90
– 0.75
– 1.25
0.00
– 1.00
B–3
B–4
B–5
0.00
0.00
0.00
0.00
0.00
B–6
+ 0.40
L
– 1.00
B–2
0.00
0.00
+ 1.50
L
B–1
+ 0.80
b)
Take-off
L/4
0.00
+ 0.35
0.00
0.00
L/3
a)
Profile
number
L/4
L/4
L/4
+ 0.75
A– 5
A– 6
Take-off
+1.00
A– 1
A– 2
A2-3
– 1.20
– 0.40
– 0.75
– 0.80
– 1 .5 0
L/3
d)
c)
Figure A2-1.
Selected study profiles
31/8/06
Corr.
A2-4
Aerodrome Design Manual
4.
DEFINING A SINGLE EQUIVALENT SLOPE
4.1 A number of single slope indices for defining non-uniform profiles were chosen for comparison as
means of describing a variable slope by a single equivalent slope. Four indices, defined as follows, were
compared:
Index No. 1
Average slope, defined as the difference in elevation between the end points of the
runway divided by the length of the runway (referred to as Runway Slope Index No. 1).
Index No. 2
The United States definition of effective gradient which is the distance between the
lowest and highest point on the runway divided by the length of the runway (referred to
as Runway Slope Index No. 2).
Index No. 3
Effective gradient for take-off, which divides the runway into four equal segments;
determines the average slope in each segment; and the slopes as follows:
Ge =
G1 + G2 + 2G3 + 4G4
(referred to as Runway Slope Index No, 3)
8
where G is the average segment slope.
Index No. 4
Modification of Index No. 3 as follows:
Ge =
G1 + 1 1/3 (G2) + 2 1/3 (G3) + 3 1/3 (G4)
(referred to as Runway Slope
Index No. 4)
8
It will be noted that Indices No. 3 and No. 4 reflect the greater influence of the runway slope at the high
speed portion of the take-off run.
5.
5.1
CONCLUSIONS
From the study it was concluded that:
a) based on the data available, Indices No. 1 and No. 4 describe the influence of variable runway
profiles better than Indices No. 2 and No. 3;
b) for jet aircraft, Slope Index No. 1 is adequate for describing the effect of a variable slope on runway
length. For piston-engined aircraft, Slope Index No. 4 is superior to the other indices tested;
c) the magnitude of the correction is larger for piston-engined aircraft than for jet aircraft;
d) the magnitude of the positive correction is greater than that of the negative corrections;
e) the effect of an elevation difference of 300 m on runway correction was found to be negligible for all
aircraft included in this study; and
f)
31/8/06
Corr.
the study suggests that refinement of the methods used in 4.1 for calculating runway slope index is
not warranted for the purpose of planning runway lengths.
Part 1. Runways
Appendix 2. The effect of variable runway slopes on take-off runway lengths
6.
A2-5
RECOMMENDATIONS
6.1 If the runway length is governed by jet aircraft, it is recommended that Slope Index No. 1 be used,
with the following correction applied to the required level runway length:
Per cent runway correction = 1.0 + 6.0 (Slope Index No. 1)
where the slope index can be either a positive or a negative value. This would apply only to runways that
are not level.
6.2 If the runway length is governed by piston-engined aircraft, it is recommended that Slope Index
No. 4 be used, with the following corrections applied to the required level runway length:
For positive index values:
Per cent runway correction = 12.0 (Slope Index No. 4)
For negative index values:
Per cent runway correction = 8.0 (Slope Index No. 4)
6.3 If it is desired to use a single index for all aircraft types, it is recommended that Slope Index No. 4
be used and the following corrections applied:
For positive index values:
Per cent runway correction (jet aircraft) = 7.0 (Slope Index No. 4)
Per cent runway correction (piston aircraft) = 12.0 (Slope Index No. 4)
For negative index values:
Per cent runway correction (jet aircraft) = 4.0 (Slope Index No. 4)
Per cent runway correction (piston aircraft) = 8.0 (Slope Index No. 4)
___________________
31/8/06
Corr.
Appendix 3
AEROPLANE PERFORMANCE CURVES AND TABLES
FOR RUNWAY PLANNING PURPOSES
1.
INTRODUCTION
1.1 Runway length criteria for general airport planning information have been developed in the form of
aeroplane performance curves and tables on landing and take-off operations. An aeroplane performance
landing curve is a chart for a particular aeroplane, based on its performance capabilities, which relates
aeroplane landing mass and aerodrome elevation to the runway length required for landing. An aeroplane
performance take-off curve is a chart for a particular aeroplane based on its performance capabilities, which
relates aeroplane take-off mass or flight distance, aerodrome elevation and temperature to the runway
length required for take-off.
1.2 An aeroplane performance table serves a purpose similar to the aeroplane performance curve.
Whereas in the performance curves the relationship between the operational factors and runway length
required is expressed in a graphical form, in the performance tables the relationship is expressed in tabular
form.
1.3 Advisory Circular AC 150/5325-4B, Runway Length Requirements for Airport Design produced by
the Federal Aviation Administration (FAA), United States, contains planning data for landing and take-off
requirements of commonly used aeroplanes. The data are presented in the form of performance curves and
tables. The circular includes examples with instructions on the use of the performance curves and tables,
and a discussion of the factors considered in their development. The relationship between elevation,
temperature, aeroplane mass and runway length presented in the performance curves and tables is based
on flight test and operational data except for those cases where preliminary performance data, based on
estimated operational data, have been developed.
1.4 Aeroplane performance curves for runway planning purposes can also be found in the aircraft
characteristics documents for airport planners. These documents contain basic planning information on
aircraft and are made available in a standardized format by aircraft manufacturers with the assistance of
airlines and aerodrome authorities. The documents include data for those existing aeroplane types which
are expected to constitute the bulk of the international fleet for the next few years.
2.
PARAMETERS TAKEN INTO ACCOUNT IN THE PERFORMANCE
CURVES AND TABLES
General
2.1 Besides the basic design features including aerodynamic and powerplant characteristics of the
aeroplanes, the factors which affect the runway length requirements include: aeroplane configuration,
aeroplane mass, atmosphere (ambient air pressure, temperature and relative humidity), runway slope,
A3-1
A3-2
Aerodrome Design Manual
runway state, and wind. However in the construction of take-off and landing performance curves and tables,
it is a usual practice to relate these factors to a standard relative humidity and zero runway slope.
Aeroplane types
2.2 The differences in the certification and operational requirements between types of present day
aeroplanes demand individual consideration of the runway length required by each aeroplane at each
aerodrome. Both the landing and take-off runway length requirements must be considered in order to
determine which is greater.
Aeroplane configuration
2.3 Aeroplane configuration refers to the position of the various elements of the aeroplane affecting its
aerodynamic characteristics. The following elements affect aeroplane performance:
a) Wing flaps and other lift-increasing devices. In the construction of the FAA aeroplane performance
curves and tables (relating to the take-off and landing distance) the position of the wing flaps (and of
other lift-increasing devices as slats, droop leading edges, etc., if applicable) normally used for the
combination of aeroplane mass, temperature and altitude has been chosen.
b) Air brakes and other drag-increasing devices. In the construction of the FAA aeroplane performance
landing curves and tables the position of the air brakes and the other drag-increasing devices, if
applicable, normally used for the combination of aeroplane mass and altitude has been chosen.
c) Other systems. The use of an anti-icing system and windshield wipers, the position of cowling flaps,
etc., also affect runway length required. In developing the FAA aeroplane performance curves and
tables these systems have been assumed to be in the position requiring the shorter runway.
Atmosphere
2.4 The atmosphere plays an important part in the runway length required. The atmosphere is a
related combination of pressure, temperature and density.
a) Altitude. Generally, as height above sea level increases, the air pressure and density become less.
The consequence of these factors upon aeroplane operations is a reduction of lift for a given true
airspeed, a reduction of power and a reduction of propeller efficiency, if applicable. The combined
result of these reductions is that it takes longer to attain the forward speed necessary to produce the
required lift, thus the runway length required for take-off for a given aeroplane becomes
progressively longer as it is operated from aerodromes at higher altitudes. Similarly, at higher
altitudes, true landing speeds are greater, and less dense air reduces the drag available to assist in
decelerating during the landing roll. In the aeroplane performance curves and tables the runway
length required is given for varying pressure altitudes (defined by the ICAO Standard Atmosphere)
as is also done in the aeroplane flight manuals, but the pressure altitude lines are labelled as
aerodrome elevation. This substitution is warranted because of the degree of similarity between the
average pressure altitude and the elevation of a location. Since the likelihood of simultaneous
occurrence of both maximum pressure altitude (minimum pressure) and mean maximum
temperature (aerodrome reference temperature) is very slight, the use of both maximum altitude and
temperature may result in an uneconomical runway length.
Part 1. Runways
Appendix 3. Aeroplane performance curves and tables for runway planning purposes
A3-3
b) Temperature. The performance of an aeroplane depends on several factors among which
temperature is important. At a given pressure, higher temperature results in lower air density and so
has an adverse effect on both piston-engined and jet aeroplanes. This effect is usually greatest
when taking off, especially for aeroplanes equipped with turbo-jet engines. The efficiency of a turbojet engine depends in part on the difference between the outside air temperature and the maximum
temperature attainable in the combustion chamber. As the outside temperature increases above a
certain value depending on the altitude, engine efficiency is decreased and, therefore, the
aeroplane’s performance is reduced. A temperature not lower than the aerodrome reference
temperature, as defined in Annex 14, Chapter 2, should be used. The effect of temperature is
considerably greater on the take-off distance (and take-off run) than on the landing distance.
Moreover the landing distance given in the flight manual usually is multiplied by an operational factor
of the order of 1.67. Since the influence of the temperature alone on the landing distance is
considerably smaller, only the influence of the ambient air pressure (with the temperatures
corresponding to the Standard Atmosphere) on the landing distance is usually taken into account.
However, the take-off distances (and take-off runs) are determined taking into account the influence
of the ambient air temperature.
Wind
2.5 The aerodrome must be designed to accommodate aeroplane operations under most normal wind
conditions. A tail wind on one runway is a head wind on a runway with a reciprocal heading. Runway lengths
increase with tail wind, so when using the bi-directional runway concept (i.e. theoretically utilizing a head
wind for all conditions in establishing runway length), the zero-wind condition is critical for both take-off and
landing. This requires, however, a change in operational direction on the runway each time the wind
changes direction and does not provide adequate length when tail wind operations are conducted because
of preferential runway use. The problem is further compounded by the fact that winds up to 9.2 km/h (5 kt)
are reported as “calm”. The FAA landing performance curves and tables are usually based on a 9.2 km/h
(5 kt) tail wind to recognize the flexibility required in aeroplane landing operations. The FAA take-off
performance curves and tables, however, are developed for zero wind. The take-off performance curves in
the aeroplane characteristic documents for airport planners are developed for zero wind and the landing
performance curves are developed for zero wind at 15 m (50 ft) height.
Aeroplane mass
2.6 The greater an aeroplane’s mass, the longer its required runway length, both for landing and for
taking off. The mass of an aeroplane is made up of three major items:
a) aircraft prepared for service (APS) mass (or operating mass empty) which usually includes:
1) aircraft empty mass;
2) crew mass, crew’s baggage, engine oil and removable emergency equipment mass;
3) unusable fuel mass;
b) payload; and
c) fuel load.
Items b) and c) are self-explanatory.
A3-4
Aerodrome Design Manual
The total of the APS mass and payload will vary and may need to be considered on a local basis. This mass
is often referred to, for operational purposes, as the “zero fuel mass” and the maximum value is given as a
structural limitation in the flight manual.
2.7 In the FAA aeroplane performance tables, the runway lengths required are related directly to the
operating mass of the aeroplanes. However, in the FAA aeroplane performance curves, the runway lengths
required may be related to flight stage lengths. In these curves it has been assumed that aeroplanes take off
with the maximum payload permissible under the circumstances. If the take-off mass is not limited by any of
the conditions enumerated in 2.11 b), the payload can be as much as the aeroplane structure permits, i.e.
the maximum zero fuel mass minus the APS; on the other hand, if the take-off mass is limited by any of the
conditions, the payload must be reduced. These curves make allowance for this.
2.8
Annex 6, Part I, Chapter 4, specifies the amount of fuel to be carried by aeroplanes for two cases:
a) when a destination alternate aerodrome is required; and
b) when a destination alternate aerodrome is not required.
In the FAA aeroplane performance, only case b) has been taken into account. According to the Annex, in
this case a flight shall not be commenced unless, taking into account both the meteorological conditions and
delays that are expected in flight, the aeroplane carries sufficient fuel and oil to ensure that it can safely
complete the flight. In addition, a reserve shall be carried to provide for contingencies and to enable the
aircraft to reach an alternate aerodrome. In order to comply with this, the fuel shall be at least the amount
sufficient to allow the aeroplane:
a) in the case of propeller-driven aeroplanes, to fly to the aerodrome to which the flight is planned,
thence to the most critical (in terms of fuel consumption) alternate aerodrome specified in the
operational flight plan and thereafter for a period of 45 minutes;
b) in the case of aeroplanes equipped with turbo-jet engines, to fly to and execute an approach and a
missed approach at the aerodrome to which the flight is planned and thereafter:
1) to fly to the alternate aerodrome specified in the flight plan, and then
2) to fly for 30 minutes at holding speed at 450 m (1 500 ft) above the alternate aerodrome under
standard temperature conditions, and approach and land, and
3) to have an additional amount of fuel sufficient to provide for the increased consumption on the
occurrence of any of the potential contingencies listed below and specified by the operator to
the satisfaction of the State of the Operator:
a) meteorological conditions forecast;
b) expected air traffic control routings and traffic delays;
c) one instrument approach at the destination aerodrome, including a missed approach;
d) the procedures prescribed in the operations manual for loss of pressurization, or failure of
one power unit while en route; and
e) any other conditions that may delay the landing of the aeroplane or increase fuel and/or oil
consumption.
Part 1. Runways
Appendix 3. Aeroplane performance curves and tables for runway planning purposes
A3-5
Annex 6 also specifies the amount of fuel in a case where the aeroplane flies directly to the alternate
aerodrome without overflying the aerodrome to which the flight is planned. This case is not the primary
concern to aerodrome engineers and was disregarded in the FAA aeroplane performance curves.
2.9 In order to assess the required amount of fuel, the average representative fuel consumption rate
has been statistically obtained in the FAA aeroplane performance curves for each type of aeroplane by
averaging the amount of fuel consumed for a unit distance and for a unit flight time. The use of this average
is justified for aerodrome design purposes as the rate is almost constant for each aeroplane type, and there
has been no significant divergency for a wide range of different stage distances. The distance scale for the
take-off performance curves has been scaled to this average representative fuel consumption rate.
2.10 In the FAA aeroplane performance curves the distance from the aerodrome of destination to an
alternate aerodrome has uniformly been assumed to be a 30-minute flight. In addition, the amount of fuel
required for a 45-minute flight at an average altitude has been taken into account. The amount of fuel
required for a turbo-jet aeroplane to fly for 45 minutes at the average altitude at the average speed is
considered to be almost equivalent to that required for a 30-minute flight at holding speed at 450 m (1 500 ft)
above an aerodrome. Further, the average representative fuel consumption rate has been obtained by
dividing the actual fuel consumption by the distance flown and by the flight time on a block-to-block basis
and it therefore includes, on an average basis, the factors enumerated in 2.8 3) b).
2.11
Aeroplane landing and take-off masses calculated should not be greater than the following limits:
a) Landing mass. Aeroplanes land at a mass up to the maximum landing mass which falls into one of
two types;
1) Structural limitation. Maximum landing mass based on structural limitation is constant regardless
of the operational parameters such as temperature and wind.
2) Climb performance. Maximum landing mass based on a climb limitation varies with pressurealtitude and temperature. An increase in pressure-altitude and/or temperature decreases the
maximum allowable landing mass.
b) Take-off mass. Aeroplanes take off at a mass up to maximum take-off mass which falls into one of
five types:
1) Structural limitations. Maximum take-off mass based on climb structural limitations is constant
regardless of pressure-altitude, temperature, wind and runway slope.
2) Climb performance. Maximum take-off mass based on climb limitations varies with pressurealtitude and aerodrome temperature. An increase in pressure-altitude and/or temperature
decreases allowable take-off mass.
3) Tire speed. Maximum take-off mass based on tire speed limitations varies with pressure-altitude,
temperature and tail wind. An increase in any of these factors, singly or in combination,
decreases maximum allowable take-off mass.
4) Maximum landing mass. Take-off mass less the fuel mass consumed to fly to the aerodrome to
which the flight is planned should not exceed the maximum landing mass at that aerodrome to
ensure safe landing after a normal flight. (See Annex 6, Part I, 5.2.)
5) Obstacle clearance. Maximum take-off mass based on obstacle clearance limitation is
dependent on the location and height of obstacles in the vicinity of the runway end. In the
A3-6
Aerodrome Design Manual
development of the FAA aeroplane performance curves, it has been assumed that there are no
obstacles that may adversely affect aeroplane operations.
Runway surface state
2.12 A snow-, slush-, ice- or water-covered runway surface will increase the length of runway required
for take-off and for landing. In the FAA aeroplane performance curves a dry hard runway surface has been
assumed unless otherwise stated; in the tables, however, the landing lengths assume a wet runway and no
further correction to the length is necessary for a wet runway. The landing performance curves in the
aeroplane characteristics documents for airport planners are developed for dry and wet runway surface
conditions.
___________________
Appendix 4
RUNWAY TURN PADS
1.
INTRODUCTION
Annex 14, Volume I requires that aircraft turn pads be provided on runways at airports where a taxiway
system, capable of facilitating faster clearance of landing aircraft from the runway, is not provided. A runway
turn pad is defined as an area on a land aerodrome adjacent to a runway for the purpose of completing a
180-degree turn on a runway where no taxiway exists. The additional pavement of the turn pad is intended
to facilitate the safe and easy turn-around of aircraft while enhancing airport capacity at such airports. With
careful planning, additional taxiway components can be added to the system in stages to keep pace with
traffic growth. See Figure A4-1.
2.
LOCATION
Runway turn pads should be located on either side of the runway, adjoining the pavement at both ends of
the runway. Where deemed necessary, runway turn pads may also be located along the runway at
intermediate locations.
3.
DESIGN CONSIDERATIONS
3.1 To facilitate the entry of aircraft onto the turn pad from the runway, the intersection angle of the
turn pad with the runway should not exceed 30 degrees. The total width of the turn pad and runway should
be such that the nose wheel steering angle of the aircraft for which the turn pad is intended will not exceed
45 degrees. The design of the runway turn pad should be such that when the cockpit of an aeroplane is over
the turn pad marking, the wheel-to-pavement edge clearance distance should not be less than that specified
in Annex 14, Volume I. An example of the pavement required for a Code letter “A” aircraft to complete a 180degree turn on a 30 m wide runway is found in Figure A4-2. Examples of runway turn pad designs can be
found in Figures A4-3 to A4-10.
3.2 Where severe weather conditions (rain and/or snow) and resultant lowering of surface friction
characteristics prevail, a larger wheel-to-pavement edge clearance of 7 m should be provided for codes E
and F aeroplanes. Nevertheless, the surface of a runway turn pad should be so constructed as to provide
good friction characteristics for aeroplanes using the facility when the surface is wet, and it should be sloped
to prevent the accumulation of water and promote drainage. Suitable longitudinal and transverse slopes
contiguous with the associated runway slopes and not exceeding 1 per cent should be provided.
3.3 The pavement strength of the turn pad should be at least equal to that of the runway served by the
turn pad, and it should be able to withstand the higher stresses put on the pavement by a slow moving
aeroplane making hard turns. In the case of flexible pavements, the surface would need to be capable of
withstanding the horizontal shear forces exerted by the main landing gear tires during turning manoeuvres.
A4-1
A4-2
Aerodrome Design Manual
4.
SHOULDERS
4.1 Runway turn pads should be provided with shoulders that are wide enough to prevent jet blast
surface erosion from the turning aeroplane and foreign object ingestion damage to the aeroplane engines.
As a minimum, the width of the shoulders would need to cover the outer engine of the most demanding
aeroplane and thus may be wider than the associated runway shoulders.
4.2 Runway turn pad shoulders should be capable of withstanding the occasional passage of the
aeroplane it is designed to serve without inducing structural damage to the aeroplane and to the supporting
ground vehicles that may operate on the shoulder.
Future taxiway
L
(b)
(a)
W
Runway turn pad
30°
Yellow guidance line
30°
Runway centre line
Runway
Figure A4-1.
Runway turn pad. Typical design
Part 1. Runways
Appendix 4. Runway turn pads
A4-3
Code letter ‘A’ aircraft
Runway width = 30 m
Outer wheel track = 4.5 m
Aircraft cockpit to main gear distance = 5.7 m
Radius of curvature = 11.875 m
C = minimum edge clearance as specified in
Annex 14, Volume I, paragraph 3.3.6
3.6
C
Outer main gear track
30.00
C
Runway centreline
30.0
Nose wheel trace
Cockpit trace
C
Figure A4-2.
Pavement required to complete a 180-degree turn —
Code letter “A” aircraft
A4-4
Aerodrome Design Manual
Code letter ‘B’ aircraft
Runway width = 30 m
Outer wheel track = 8.0 m
Aircraft cockpit to main gear distance = 11.9 m
Radius of curvature = 18.75 m
C = minimum edge clearance as specified in
Annex 14, Volume I, paragraph 3.3.6
13.7
34.4
21.16
C
5.4
7.9
C
C
Outer main gear track
30.0
Runway centreline
37.9
Nose wheel trace
Cockpit trace
C
Figure A4-3.
Turn pad design for a Code letter “B” aircraft
Part 1. Runways
Appendix 4. Runway turn pads
A4-5
Code letter ‘C’ aircraft (MD-80)
Runway width = 45 m
Outer wheel track = 9.0 m
Aircraft cockpit to main gear distance = 20.3 m
Radius of curvature = 22.0 m
C = minimum edge clearance as specified in
Annex 14, Volume I, paragraph 3.3.6
11.7
51.3
25.5
5.2
6.8
C
C
Outer main gear track
C
45.0
Runway centreline
Nose wheel
trace
51.8
Cockpit trace
C
Figure A4-4.
Turn pad design for a Code letter “C” aircraft
A4-6
Aerodrome Design Manual
Code letter ‘D’ aircraft (A310)
Runway width = 60 m
Outer wheel track = 10.93 m
Aircraft cockpit to main gear distance = 19.48 m
Radius of curvature = 26.0 m
C = minimum edge clearance as specified in
Annex 14, Volume I, paragraph 3.3.6
59.5
21.0
35.8
C
12.1
Outer main gear track
8.7
7.00
Nose wheel
trace
45.0
57.1
C
Runway centreline
Cockpit
trace
C
Figure A4-5.
Turn pad design for a Code letter “D” aircraft (A310)
Part 1. Runways
Appendix 4. Runway turn pads
A4-7
Code letter ‘D’ aircraft (MD-11)
Runway width = 45 m
Outer wheel track = 14 m
Aircraft cockpit to main gear distance = 31.0 m
Radius of curvature = 33.25 m
C = minimum edge clearance as specified in
Annex 14, Volume I, paragraph 3.3.6
78.3
44.2
46.9
C
9.2
25.5
Outer main gear track
C
C
Nose wheel
trace
70.5
Runway centreline
45.0
Cockpit trace
C
Figure A4-6.
Turn pad design for a Code letter “D” aircraft (MD-11)
A4-8
82.0
110.9
C
10.4
47.4
92.4
C
C
Outer main gear track
45.0 Runway centreline
Cockpit trace
C
Aerodrome Design Manual
Figure A4-7. Turn pad design for a Code letter “E” aircraft
(wheel base greater than 25.6 m — Runway width = 45 m)
Code letter ‘E’ aircraft with the wheel base greater than 25.6 m
Runway width = 45 m
Outer wheel track = 12.88 m
Aircraft cockpit to main gear distance = 34.85 m
Radius of curvature = 40.0 m
C = minimum edge clearance as specified in
Annex 14, Volume I, paragraph 3.3.6
Part 1. Runways
Appendix 4. Runway turn pads
Figure A4-8. Turn pad design for a Code letter “E” aircraft
(wheel base up to 25.6 m — Runway width = 45 m)
Code letter ‘E’ aircraft with the wheel base up to 25.6 m
Runway width = 45 m
Outer wheel track = 14.0 m
Aircraft cockpit to main gear distance = 28.0 m
Radius of curvature = 40.0 m
C = minimum edge clearance as specified in
Annex 14, Volume I, paragraph 3.3.6
110.9
82.0
69.8
10.4
C
47.4
92.4
C
C
Outer main gear track
Nose wheel trace
Runway centreline
45.0.
Cockpit trace
C
A4-9
A4-10
111.7
68.9
77.7
C
44.8
C
Outer main gear track
104.8
77
7-
30
0
Runway centreline
30
0
60.0
77
7-
Cockpit trace
C
Aerodrome Design Manual
Figure A4-9. Turn pad design for a Code letter “E” aircraft
(wheel base greater than 25.6 m — Runway width = 60 m)
Code letter ‘E’ aircraft with the wheel base greater than 25.6 m
Runway width = 60 m
Outer wheel track = 12.88 m
Aircraft cockpit to main gear distance = 34.85 m
Radius of curvature = 49.0 m
C = minimum edge clearance as specified in
Annex 14, Volume I, paragraph 3.3.6
Part 1. Runways
Appendix 4. Runway turn pads
Figure A4-10.
Code letter ‘F’ aircraft
Runway width = 60 m
Outer wheel track = 16 m
Aircraft cockpit to main gear distance = 30.0 m
Radius of curvature = 46.5 m
C = minimum edge clearance as specified in
Annex 14, Volume I, paragraph 3.3.6
119.2
78.5
74.8
— END —
Turn pad design for a Code letter “F” aircraft
C
11.0
45.3
C
C
Outer main gear track
105.3
Nose wheel
trace
60.0
Runway centreline
Cockpit trace
C
A4-11