This document provides troubleshooting steps for issues with RB433AHr3 and RB433UAHr3 boards, including no power, PoE not working, board not booting properly, Ethernet or USB not working. It lists components to check and potential replacements if issues are found with voltage regulation, switching controllers, connectors, crystals and more. Replacement part numbers are provided for common components.
This document provides troubleshooting steps for issues with RB433AHr3 and RB433UAHr3 boards, including no power, PoE not working, board not booting properly, Ethernet or USB not working. It lists components to check and potential replacements if issues are found with voltage regulation, switching controllers, connectors, crystals and more. Replacement part numbers are provided for common components.
This document provides troubleshooting steps for issues with RB433AHr3 and RB433UAHr3 boards, including no power, PoE not working, board not booting properly, Ethernet or USB not working. It lists components to check and potential replacements if issues are found with voltage regulation, switching controllers, connectors, crystals and more. Replacement part numbers are provided for common components.
This document provides troubleshooting steps for issues with RB433AHr3 and RB433UAHr3 boards, including no power, PoE not working, board not booting properly, Ethernet or USB not working. It lists components to check and potential replacements if issues are found with voltage regulation, switching controllers, connectors, crystals and more. Replacement part numbers are provided for common components.
Copyright:
Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
You are on page 1/ 8
TroubleShooting for RB433AHr3, RB433UAHr3
These repair instructions are for NON WARRANTY repairs only! Please make visual inspection for signs of corrosion or mechanical damages before starting.
No power, blue LED isnt lit
NOT OK
Check Schottky diode D802
OK
Change faulty diode D802
OK
NOT OK Check PNP transistor Q802 and Zener diode D803 Change faulty components
Check Zener diode D804
OK
NOT OK
Check P-channel MOSFET Q801
OK NO 10 Ohm
Change faulty P-channel MOSFET Q801
Check R819 resistor resistance. It should be 10 Ohm
OK
Change faulty resistor R819
Check PWM controller U803. On the pin#1 should be 4.45.0V
OK
NOT OK
Change faulty PWM controller U803
NOT OK
Check N-channel MOSFETs Q806, Q808
OK
Change faulty MOSFETs
Short circuit
Check short circuit on 1.8V, for example, on C612 pins
Unsolder Ethernet Switch U601 and check 1.8V for short circuit OK
Problem still appears
Change faulty Ethernet Switch U601
The board is unrepairable
PoE doesnt work
NOT OK
Check Schottky diode D801
OK NOT OK
Change faulty diode D801
Check Ethernet connector J601
Problem still appears
Change faulty connector J601
The board is unrepairable
Doesnt boot, green and blue LEDs are lit
NOT OK Check 2.5V output, for example, on C841 pins Check N-channel MOSFET Q807 NOT OK
Check voltage on PWM controller pin#7 (PGOOD). It voltage should be 3.3V OK
OK
Check resistor R307 resistance. It resistance should be 68KOhm.
NO 1.2V Check 1.2V CPU core output, for example, on C848 pins
Check ferrite bead FB801. It resistance should be less than 1 Ohm NOT OK
OK
Check Step Down DC-DC convector U806 NOT OK Change faulty Step Down convector U806
OK
Change faulty ferrite bead FB801
NOT OK Check 40.000MHz clock on oscillator Y301 pin#3 Change faulty oscillator Y301
Problem still appears
The board is unrepairable
Ethernet doesnt work
Check termination resistance between Tx and Rx lines in the each Ethernet connector J601, J602, J603. It should be 150 Ohm +/-2% OK NOT OK
Change faulty connectors
Check voltage drop between D601, D602 or D603 pin#1 and Ground. This value should be in the range from 0.4 0.5V measured in diode mode (hold positive wire on the ground and COM wire to D601 pin#1)
NOT OK
Change faulty Ethernet Switch U601
OK
Check ferrite beads FB602 (for J601), FB604 (for J602), FB603 (for J603). It resistance should be less than 1 Ohm OK
NOT OK
Change faulty ferrite beads
No 1.8V
Check 1.8V output, for example, on PNP transistor Q601 pins
OK
Check Q601 transistor
NOT OK
Change faulty U601
OK
Change faulty Q601
NO 25.000 MHz
Check 25.000MHz clock on crystal Y601 Problem still appears
Change faulty Y601
The board is unrepairable
USB doesnt work (only for RB433UAH)
NOT OK
Check USB connectors J302, J303 for mechanical damage
Change faulty USB connectors
OK
NO 5.0V
Check 5.0V output, for example, on C814 pins
Check resistor R804 OK Check N-channel OK resistance. It should Dual MOSFET Q805 be 10 Ohm NOT OK
Check PWM controller U802. On pin#1 should be 0.8V
NOT OK
Change faulty MOSFET Q805
NO 10 Ohm
Change faulty PWM controller U802
Check ferrite beads FB302, FB301, FB703. It resistance should be less than 1 Ohm OK
