Kathrein Antenna

Photo on title page: Selection of products for UMTS networks.
Catalogue Issue 02/04 All data published in previous catalog issues hereby becomes invalid. We reserve the right to make alterations in accordance with the requirements of our customers, therefore for binding datas please check valid datasheets!
Please note:
As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions.
The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4, which include the static mechanical load imposed on an antenna by wind at maximum velocity. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground. These facts must be considered during the site planning process.
The details given in our data sheets have to be followed carefully when installing the antennas and accessories. In addition, please use our information brochure about mounting configurations. The installation team must be properly qualified and also be familiar with the relevant national safety regulations.
Quality leads the way

Being the oldest and largest antenna manufacturer worldwide, we take on every day the challenge arising from our own motto. One of our basic principles is to look always for the best solution in order to satisfy our customers. Our quality assurance system conforms to DIN EN ISO 9001 and applies to the product range of the company: Antenna systems, communication products as well as active and passive distribution equipment.
GSM 900 GSM-R GSM 850 CDMA 800
XPol
VPol
XPol GSM 1800 GSM 1900 PCS
XXPol Dual-band
VPol
XPol Multi-band
XXPol 2-Multi-band
UMTS
XXPol Dual-band
XXXPol Triple-band
VPol Single-/Multi-band
Omni
VPol
Indoor
VPol
RET
Remote Electrical Tilt-System
Electrical Accessories
Splitters / Tappers Filter Products
Mechanical Accessories
Clamps, Downtilt Kits, ...
List of available Catalogues for Mobile Communication Antennas and Accessories
790 2500 MHz Base Station Antennas for Mobile Communications
27 512 MHz Base Station Antennas for Mobile Communiations
Ground-to-Air Communication Antennas
Antennas for Trains and Busses
790 2500 MHz Filters, Combiners, Amplifiers for Mobile Communications
450 MHz Filters, Combiners, Amplifiers for Mobile Communications
80 / 160 MHz Filters, Combiners Amplifiers for Mobile Communications
The listed catalogues are also available on CD-ROM
Summary of Types
The articles are listed by type number in numerical order.
Type No.
Page
Type No.
Page
Type No.
Page
Type No.
Page
730 ...
730 368 730 376 730 378 730 380 730 382 730 677 730 691 43 46 48 49 50 43 44
734 328 734 330 734 360 734 361 734 362 734 363 734 364 734 365
74 75 194 194 194 194 194 194
737 547 737 971 737 972 737 973 737 974 737 975 737 976 737 978
45 190 189 189 189 189 190 189
739 630 739 632 739 633 739 634 739 636 739 637 739 648 739 649 739 650
23 17 18 20 24 24 26 29 31 28 26 29 32 27 30 33 19 22 25 56 57 57 58 133 45 50 52
731 ...
731 651 186
735 ...
735 147 735 727 73 40
738 ...
738 187 738 192 738 440 134 126 201 114 114 129 122 136 186 198
739 655 739 658 739 660 739 662 739 664 739 665 739 666 739 684 739 685 739 686 739 695 739 707
732 ...
732 317 732 318 732 319 732 321 732 322 732 327 732 689 732 691 732 967 197 197 197 197 197 197 46 44 48
736 ...
736 347 736 349 736 350 736 854 736 855 736 801 736 802 736 803 736 804 127 128 125 47 47 170 ... 170 ... 170 ... 170 ... 170 ...
738 445 738 446 738 449 738 450 738 454 738 546 738 908
739 ...
739 136 739 489 739 490 72 83 53 53 54 55 55 16 16 17 20 23
739 708 739 710 739 785 739 854 739 856 739 927
733 ...
733 677 733 678 733 679 733 680 733 695 733 736 186 186 186 186 41 41 ...
736 805
737 ...
737 190 737 303 737 304 737 305 737 306 135 171 171 171 171 171 171 199
739 491 739 494 739 495 739 498 739 619 739 620 739 622 739 623 739 624
741 ...
741 264 741 316 741 320 741 322 741 324 54 60 61 64 66
734 ...
734 304 734 318 73 74
737 307 737 308 737 398
Summary of Types
The articles are listed by type number in numerical order.
Type No.
Page
Type No.
Page
Type No.
Page
Type No.
Page
741 326 741 327 741 328 741 336 741 344 741 415 741 572 741 573 741 622 741 623 741 717 741 785 741 786 741 790 741 794 741 862 741 984 741 987 741 988 741 989 741 990
62 65 67 68 69 116 143 142 21 52 14 15 120 137 89 131 91 92 93 94 95
742 211 742 212 742 213 742 215 742 218 742 219 742 222 742 226 742 233 742 234 742 235 742 241 742 263 742 264 742 265 742 266 742 270 742 271 742 272 742 290 742 351 742 445
84 87 90 88 80 81 103 102 98 99 100 111 195 104 105 106 108 109 110 118 79 117
800 10111 800 10137 800 10141 800 10147 800 10173 800 10177 800 10202 800 10203 800 10204 800 10207 800 10247 800 10251
132 143 14 130 144 144 34 35 36 37 85 78
K 61 ...
K 61 14 02 K 61 14 03 K 61 14 04 K 61 14 05 K 61 33 5 K 61 33 6 40 40 ... 40 ... 40 ... 200 200
K 63 ...
K 63 20 62 1 K 63 20 62 7 K 63 23 60 01 K 63 23 60 67 170 170 175 174 174 174
850
850 10002 850 10003 850 10006 850 10007 186 ... 186 ... 188 191
K 63 23 61 07 K 63 23 61 57
K 73 ...
K 73 22 67 K 73 45 64 7 42 41
860
860 10002 860 10003 860 10006 164 161 162 163 172 172 172 173 173 173 175 162 165 166
K 75 ...
K 75 11 61 K 75 15 64 1 123 124
742 ...
742 033 742 034 742 035 742 036 742 047 742 113 742 149 742 151 742 192 742 196 742 210 187 187 187 187 70 196 141 63 115 86 82
782
782 10147 782 10148 782 10149 782 10253 782 10254 782 10255 782 10256 167 167 167 168 168 168 168
860 10007 860 10017 860 10018 860 10019 860 10020 860 10021 860 10022 860 10023 860 10026
800
800 10046 119
860 10030 860 10031
Antenna Designs: Antenna Families Harmony of Design and Technology
Omni
A-Panel C-Panel
F-Panel
Eurocell Panel
Antenna Designs: Antenna Families Distinguishing features
Design Radome
Small size and elegant design are the distinguishing features of Kathreins antenna families. The radomes cover the internal antenna components. Fiberglass material guarantees optimum performance with regards to stability, stiffness, UV resistance, painting and best weather protection. The design of Kathrein antennas is based on fundamental engineering knowledge and also on decades of practical experience, during which the various constructions and materials used have proved their outstanding reliability. Kathrein cellular antennas are designed to operate under the environmental conditions as described in ETS 300 019-1-4 class 4.1 E. The antennas exceed this standard with regards to the following items: Low temperature: 55 C High temperature (dry): +60 C According to the antenna type selected, customer can choose from different half-power beam widths. Gain values up to 22.5 dBi and electrical downtilts up to 15 for panel antennas are available. Downtilts are either fixed or adjustable or even controlled by remote electrical tilt system (RET).
Environmental influences
Environmental conditions
Large variety of half-power beam width, gain values, electrical downtilt
Low intermodulation After many years of experience in the construction of antennas and after products (typically 150 dBc) intensive research into the effects of intermodulation, we have been able to optimize the material and technology used for antennas (the given value refers to 3rd order products measured with 2 carriers of 20 W each). Multi-band design Depending on antenna family broad-band, multi-band, dual-band and triple-band versions can be offered. Therefore the varity of antennas used can be kept to a minimum. The antennas are DC grounded according EN 50083-1. Depending on the type, the antennas are equipped with up to 3 fixing points. Panels can be wall mounted without any additional hardware. For mast mounting, stainless steel brackets and mechanical downtilt kits are available. To assist the installation technicians in aligning the panels, an azimuth adjustment tool can be supplied (see Mechanical Accessories).
Excellent grounding Multi-functional installation hardware
Directional Antenna Designs: Special Directional Antennas For Particular Applications
Antennas for
tunnel use
The distinguishing features of these special versions, e.g. parabolic panels or log. periodic antennas, are: very small half-power beam width (high gain)
railway use high sidelobe suppression micro cells (street use) also Dual-band and Multi-band versions high gain link for repeaters bidirectional horizontal pattern.
LogPer
ParPanel BiDir
10
Downtilting of Antennas: Downtilt Possibilities
Mechanical downtilt Electrical downtilt
For further technical information please see Mechanical Accessories, pages 189 and 197. Description of the interface (protective cap removed):
1 2
Adjustment wheel with twist-lock function. Downtilt spindle with integrated scale.
Thread for fixing of the protective cap or the RCU (Remote Control Unit). Gearwheel for RCU-power drive.
To set the downtilt angle exactly, you must look horizontally at the scale. The lower edge of the gearwheel must be used for alignment purposes.
Manual adjustment procedure: (General example)

max. 0
0 max.
Remove protective cap.
Set downtilt angle by rotating the adjustment wheel.
Screw on the protective cap again.
For antennas without RET, the interface looks different. In this case you just have to rotate the adjustment wheel in order to set the downtilt.
Remote Electrical Tilt (RET) For further technical information please see RET, page 150...
11
Kathrein Antennas Product Description (Type)
XXPol A-Panel 870960/17101880 C 65/ 60 17/18dBi 28T/2T
Polarization(s): (X) Dual +45/ 45 (V) Vertical
Antenna Family
Frequency Range(s)
Integrated Combiner
Horizontal Half-power Beam Width(s)
Gain Value(s)
Variable / Fixed Electrical Tilt(s)
12
Summary Directional Antennas Dual Polarization + 45/ 45 GSM 900 / GSM-R / GSM 850 / CDMA 800
Dual Polarization + 45/ 45
Type Type No. Height [mm] 656 1296 2580 Connector position bottom bottom bottom Page
XPol A-Panel XPol A-Panel XPol A-Panel
870960 806960 870960
30 30 30
15.5dBi 18.5dBi 21dBi
741 717 800 10141 741 785
14 14 15
XPol A-Panel XPol A-Panel XPol A-Panel XPol A-Panel XPol A-Panel XPol A-Panel XPol A-Panel XPol A-Panel XPol A-Panel XPol A-Panel XPol A-Panel XPol A-Panel XPol A-Panel XPol A-Panel XPol A-Panel
806960 806960 806960 806960 806960 806960 806960 806960 824960 824960 870960 806960 806960 806960 806960
65 65 65 65 65 65 65 65 65 65 65 65 65 65 65
9dBi 12.5dBi 15.5dBi 15dBi 15dBi 15dBi 17dBi 17dBi 17dBi 16.5dBi 18dBi 18dBi 18dBi 18dBi 17.5dBi
739 619 739 620 739 739 739 739 739 739 741 739 739 739 739 739 739 622 632 633 684 623 634 622 685 630 624 636 637 686
256 656 1296 1296 1296 1296 1936 1936 1936 1996 2580 2580 2580 2580 2580
bottom or top bottom or top bottom or top bottom bottom bottom bottom or top bottom bottom bottom bottom or top bottom or top bottom bottom bottom
16 16 17 17 18 19 20 20 21 22 23 23 24 24 25
6T 12T 014T
6T 9T 010T
6T 9T 07T
XPol A-Panel XPol A-Panel XPol A-Panel XPol A-Panel XPol A-Panel XPol A-Panel XPol A-Panel XPol A-Panel XPol A-Panel XPol A-Panel
806960 806960 824960 870960 806960 806960 806960 806960 806960 806960
90 90 88 90 88 88 88 88 88 88
13.5dBi 13.5dBi 13.5dBi 15.5dBi 15.5dBi 15.5dBi 15dBi 17dBi 17dBi 16dBi
6T 014T
739 648 739 658 739 664 739 739 739 739 655 649 660 665
1296 1296 1296 1936 1936 1936 1996 2580 2580 2580
bottom or top bottom bottom bottom or top bottom or top bottom bottom bottom or top bottom bottom
26 26 27 28 29 29 30 31 32 33
6T 010T
6T 07T
739 650 739 662 739 666
Compact Panel (C-Panel)

XPol XPol XPol XPol C-Panel C-Panel C-Panel C-Panel 806960 806960 806960 806960 65 65 65 65 15.5dBi 17dBi 18dBi 15dBi 800 800 800 800 10202 10203 10204 10207 1294 1934 2254 1294 bottom bottom bottom bottom 34 35 36 37
6T
New Products
13
GSM 900 XPol
A-Panel Dual Polarization Half-power Beam Width

XPol A-Panel 870960 30 15.5dBi
Type No. Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Front-to-back ratio, copolar Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth
800/900 X 30
741 717
870 960 MHz +45, 45 2 x 15.5 dBi
10
30
Horizontal: Vertical: > 30 dB > 30 dB 50 < 1.5
30 27
3 0
Horizontal Pattern
< 150 dBc

27
500 W (at 50 C ambient temperature) 2 x 7-16 female Bottom

3 10
13 kg
0
Frontal / Lateral / Rearside: 330 N / 60 N / 470 N 200 km/h 656 / 560 / 116 mm
Vertical Pattern
dB
dB
800/900 45
800/900 +45
7-16
7-16

Type No. Frequency range 806 894 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Front-to-back ratio, copolar Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth +45, 45 2 x 18 dBi Horizontal: Vertical: > 25 dB > 30 dB 50 < 1.5 < 150 dBc 500 W (at 50 C ambient temperature) 2 x 7-16 female Bottom 22 kg Frontal / Lateral / Rearside: 680 N / 130 N / 970 N 200 km/h 1296 / 560 / 116 mm
3 0
dB
800 10141
806960 880 960 MHz +45, 45 2 x 18.5 dBi Horizontal: Vertical: > 29 dB > 30 dB 50 < 1.5
14
10
29
31 15
29 14
3 0
Horizontal Pattern
10
Vertical Pattern
14
Mounting accessories are not included in the scope of delivery (see page 185)
dB

XPol A-Panel 870960 30 21dBi
Type No. Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Front-to-back ratio, copolar Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth
870 960 X 30
741 785
870 960 MHz +45, 45 2 x 21 dBi
10
30
30 7
3 0
Horizontal Pattern
< 150 dBc 400 W (at 50 C ambient temperature) 2 x 7-16 female Bottom
3 10
dB
40 kg
0
Vertical Pattern
dB
870960 45
870960 +45
7-16
7-16
Mounting accessories are not included in the scope of delivery (see page 185)
15
XPol
XPol

Type No. Frequency range 806 880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Front-to-back ratio, copolar Cross polar ratio Maindirection Sector Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth 0 60 +45, 45 2 x 8.5 dBi Horizontal: Vertical: > 27 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5 < 150 dBc 70 70
806 960 X 65
739 619
806960 880 960 MHz +45, 45 2 x 9 dBi Horizontal: Vertical: > 27 dB Typically: 25 dB > 10 dB
68
10 3 0
125
65
65 68
Horizontal Pattern
10
350 W (at 50 C ambient temperature) 2 x 7-16 female Bottom or top 3 kg Frontal / Lateral / Rearside: 40 N / 25 N / 90 N 200 km/h 256 / 262 / 116 mm
Vertical Pattern
dB
dB
806960 45
806960 +45
7-16
7-16

Type No. Frequency range 806 880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Front-to-back ratio, copolar Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth +45, 45 2 x 12 dBi Horizontal: Vertical: 68 29 > 30 dB > 30 dB 50 < 1.5 < 150 dBc 500 W (at 50 C ambient temperature) 2 x 7-16 female Bottom or top 6 kg Frontal / Lateral / Rearside: 110 N / 60 N / 240 N 200 km/h 656 / 262 / 116 mm
3 0
dB
739 620
806960 880 960 MHz +45, 45 2 x 12.5 dBi Horizontal: Vertical: 65 27
10
120
65
3 0
Horizontal Pattern
dB
27
10
Vertical Pattern
16
Mounting accessories are not included in the scope of delivery (see page 186 191)

Type No. Frequency range 806 880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Front-to-back ratio, copolar Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth +45, 45 2 x 15 dBi Horizontal: Vertical: 68 16 > 30 dB > 30 dB 50 < 1.4 < 150 dBc
806 960 X 65
739 622
10
120
65
3 0
Horizontal Pattern
dB
15
10
3 0
Vertical Pattern
dB
806960 45
806960 +45
7-16
7-16
XPol A-Panel 806960 65 15dBi 6T

Type No. Frequency range 806 880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth +45, 45 2 x 14.5 dBi Horizontal: Vertical: 6, fixed 14 dB > 28 dB > 30 dB 50 < 1.5 < 150 dBc
3
739 632
806960 880 960 MHz +45, 45 2 x 15 dBi Horizontal: Vertical: 6, fixed 16 dB > 30 dB > 32 dB 50 < 1.3
10 10
120
65
68 16
65 15
3 0
Horizontal Pattern
dB
15
600 W (at 50 C ambient temperature) 2 x 7-16 female Bottom 11 kg Frontal / Lateral / Rearside: 230 N / 130 N / 500 N 200 km/h 1296 / 262 / 116 mm
Vertical Pattern 6 electrical downtilt
dB
17
XPol
XPol

Type No. Frequency range 806 880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth +45, 45 2 x 14.5 dBi Horizontal: Vertical: 12, fixed 14 dB > 28 dB > 30 dB 50 < 1.5 < 150 dBc 68 17
806 960 X 65
739 633
806960 880 960 MHz +45, 45 2 x 15 dBi Horizontal: Vertical: 12, fixed 16 dB > 30 dB > 30 dB 50 < 1.3
10 10
120
65
65 16
3 0
Horizontal Pattern
dB
16
dB
806960 45
806960 +45
7-16
7-16
18
A-Panel Dual Polarization Half-power Beam Width Adjust. Electr. Downtilt

Type No. Frequency range 806 866 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression for sector 030 above horizon Front-to-back ratio, copolar Cross polar ratio Maindirection Sector Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 0 60 +45, 45 14.5 dBi Horizontal: Vertical: 0 14 70 16
806 960 X 65 0 14
set by hand or by optional RCU (Remote Control Unit)
739 684
806 960 824 894 MHz +45, 45 14.7 dBi Horizontal: 68 Vertical: 15.5 0 14 880 960 MHz +45, 45 15 dBi Horizontal: Vertical: 0 14 65 15
14 dB > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5
15 dB > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5 < 150 dBc 400 W (at 50 C ambient temperature)
15 dB > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5
Isolation, between ports
880 960 MHz: +45/ 45 Polarization

125 65 15
10 3 0
10
dB
3 0
Horizontal Pattern
Vertical Pattern 0 14 electrical downtilt 806 960 45
dB

130 68
806 960 +45
7-16
15.5
7-16
10 3 0
10
Mechanical specifications Input Connector position Adjustment mechanism Weight Wind load Frontal: Lateral: Rearside: 2 x 7-16 female Bottom 1x, Position bottom continuously adjustable 14 kg 230 N (at 150 km/h) 130 N (at 150 km/h) 500 N (at 150 km/h) 200 km/h 1562 x 287 x 165 mm 1296 / 262 / 116 mm
dB
dB
3 0
Horizontal Pattern
Vertical Pattern 0 14 electrical downtilt

135 70 16
Max. wind velocity

10 10
Packing size
dB
dB
3 0
3 0
Height/width/depth
Horizontal Pattern
Vertical Pattern 0 14 electrical downtilt 19
Mounting accessories are not included in the scope of delivery (see page 186 191) For more information about downtilt adjustment and preparation for Remote Control Unit (RCU) refer to pages 150 160
XPol
XPol

Type No. Frequency range 806 894 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth +45, 45 2 x 16.5 dBi Horizontal: Vertical: 68 10 15 dB > 30 dB > 30 dB 50 < 1.5 < 150 dBc
806 960 X 65
739 623
806960 880 960 MHz +45, 45 2 x 17 dBi Horizontal: 65 Vertical: 9.5
10
120
65
3 0
Horizontal Pattern
dB
9.5
10
3 0
Vertical Pattern first null-fill below horizon better or equal 25 dB below maximum gain
dB
806960 45
806960 +45
7-16
7-16

Type No. Frequency range 806 894 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth 20 +45, 45 2 x 16.5 dBi Horizontal: Vertical: 6, fixed 14 dB > 30 dB > 32 dB 50 < 1.5 < 150 dBc
10
739 634
806960 880 960 MHz +45, 45 2 x 17 dBi Horizontal: 65 Vertical: 9.5 6, fixed 18 dB > 30 dB > 32 dB 50 < 1.3
9.5
10
120
65
68 10
3 0
Horizontal Pattern
7-16 female Bottom 12 kg Frontal / Lateral / Rearside: 350 N / 200 N / 770 N 200 km/h 1936 / 262 / 116 mm
3 0
dB
600 W (at 50 C ambient temperature)
dB

Type No. Frequency range 824 880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth +45, 45 2 x 16.5 dBi Horizontal: Vertical: 9, fixed 14 dB > 30 dB > 32 dB 50 < 1.5 < 150 dBc 68 10
824 960 X 65
741 622
824960 880 960 MHz +45, 45 2 x 17 dBi Horizontal: 65 Vertical: 9.5 9, fixed 16 dB > 30 dB > 32 dB 50 < 1.3
10 10
120
65
3 0
Horizontal Pattern
dB
9.5
dB
824960 45
824960 +45
7-16
7-16
21
XPol
XPol

XPol A-Panel 806960 65 16.5dBi 010T
Type No. Frequency range 806 866 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable +45, 45 2 x 16 dBi Horizontal: Vertical: 0.5 10 70 10
806 960 X 65 0 10
739 685
806960 824 894 MHz +45, 45 2 x 16 dBi Horizontal: Vertical: 68 10 880 960 MHz +45, 45 2 x 16.5 dBi Horizontal: Vertical: 0.5 10 65 9.5
0.5 10
Sidelobe suppression for 0 ... 3 ... 6 ... 10T 0 ... 3 ... 6 ... 10T 0 ... 3 ... 6 ... 10T first sidelobe above horizon 15 ... 14 ... 12 ... 12 dB 15 ... 15 ... 15 ... 14 dB 17 ... 17 ... 17 ... 17 dB sector 0 30 above horizon 12 dB 13 dB 15 dB Front-to-back ratio, copolar Cross polar ratio Maindirection Sector Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 0 60 > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5 > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5 < 150 dBc 400 W (at 50 C ambient temperature) > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5

125 65 9.5
10 3 0
10
dB
3 0
Horizontal Pattern
Vertical Pattern 0.5 10 electrical downtilt 806 960 45
dB

130 68
806 960 +45
7-16
10
7-16
10 3 0
10
dB
dB
3 0
Horizontal Pattern
Vertical Pattern 0.5 10 electrical downtilt

135 70 10
Max. wind velocity

10 3 0 0 10
Packing size
dB
dB
Height/width/depth
Horizontal Pattern
22

Type No. Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth
800/900 X 65
739 630
870 960 MHz +45, 45 2 x 18 dBi
10
120
65
Horizontal: Vertical: 15 dB > 30 dB > 32 dB 50 < 1.3
65 7
3 0
Horizontal Pattern
dB
< 150 dBc

10
800/900 45 800/900 +45
3 0
dB
7-16
7-16

Type No. Frequency range 806 880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Front-to-back ratio, copolar Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth +45, 45 2 x 17.5 dBi Horizontal: 68 Vertical: 7.5 > 30 dB > 30 dB 50 < 1.5 < 150 dBc
7
739 624
806960 880 960 MHz +45, 45 2 x 18 dBi Horizontal: Vertical: > 30 dB > 32 dB 65 7
10
120
65
3 0
Horizontal Pattern
10
3 0
Vertical Pattern
dB
dB
23
XPol
XPol

Type No. Frequency range 806 880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth < 1.5 < 150 dBc +45, 45 2 x 17.5 dBi Horizontal: 68 Vertical: 7.5 18 dB > 30 dB > 32 dB 50
806 960 X 65
739 636
806960 880 960 MHz +45, 45 2 x 18 dBi Horizontal: Vertical: 65 7
10
120
65
3 0
Horizontal Pattern
6, fixed
dB
10
< 1.3
3 0
dB
806960 45
806960 +45
7-16
7-16

Type No. Frequency range 806 870 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth 24 < 1.5 < 150 dBc
3
739 637
806960 870 960 MHz +45, 45 2 x 18 dBi 65 7.5
10
120
65
+45, 45 2 x 17.5 dBi Horizontal: Vertical: 9, fixed
3 0
Horizontal Pattern
better 18 dB below maximum gain > 30 dB > 32 dB 50 < 1.3

10
dB
7.5
dB

Type No. Frequency range 806 866 MHz Polarization Gain Half-power beam width Copolar +45/ -45 Electrical tilt continuously adjustable +45, 45 2 x 17 dBi Horizontal: 70 Vertical: 7.9 0 7
806 960 X 65 0 7
739 686
806960 824 894 MHz +45, 45 2 x 17.2 dBi Horizontal: 68 Vertical: 7.7 0 7 880 960 MHz +45, 45 2 x 17.5 dBi Horizontal: Vertical: 0 7 65 7.5
Sidelobe suppression for 0 ... 2 ... 4 ... 7 T 0 ... 2 ... 4 ... 7 T 0 ... 2 ... 4 ... 7 T first sidelobe above horizon 17 ... 17 ... 17 ... 17 dB 18 ... 18 ... 18 ... 18 dB 18 ... 18 ... 18 ... 18 dB sector 030 above horizon 14 ... 14 ... 14 ... 14 dB 15 ... 15 ... 15 ... 15 dB 17 ... 17 ... 17 ... 17 dB Front-to-back ratio, copolar Cross polar ratio Maindirection Sector Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 0 60 > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5 > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5 < 150 dBc 400 W (at 50 C ambient temperature) > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5

125 65 7.5
10 3 0
10
dB
3 0
Horizontal Pattern
dB

130 68
806 960 +45
7-16
7.7
7-16
10 3 0
10
Mechanical specifications Input Connector position Adjustment mechanism Weight Wind load 2 x 7-16 female Bottom 1x, Position bottom continuously adjustable 22 kg Frontal: 470 N (at 150 km/h) Lateral: 280 N (at 150 km/h) Rearside: 1040 N (at 150 km/h) 200 km/h 2846 x 287 x 165 mm 2580 / 262 / 116 mm
dB
dB
3 0
Horizontal Pattern

135 70 7.9
Max. wind velocity

10 3 0 0 10
Packing size
dB
dB
Height/width/depth
Horizontal Pattern
XPol
XPol

Type No. Frequency range 806 880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth +45, 45 2 x 13 dBi Horizontal: Vertical: 90 16 16 dB > 25 dB > 32 dB 50 < 1.5 < 150 dBc
806 960 X 90
739 648
3 0
dB
90 170
Horizontal Pattern
15
10
3 0
Vertical Pattern
dB
806960 45
806960 +45
7-16
7-16

Type No. Frequency range 806 880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth 26 < 1.5 < 150 dBc
3
739 658
806960 880 960 MHz +45, 45 2 x 13.5 dBi Horizontal: Vertical: 15 dB > 25 dB > 30 dB 50 < 1.3
10
90 170
+45, 45 2 x 13 dBi Horizontal: Vertical: 90 16
90 15
3 0
6, fixed
Horizontal Pattern
dB
15
dB
824 960 X 88 0 14

Type No. Frequency range 824 894 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Cross polar ratio Maindirection Sector Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 0 60 +45, 45 13.5 dBi Horizontal: 85 Vertical: 15.5 014
739 664
824960 880 960 MHz +45, 45 13.5 dBi Horizontal: Vertical: 014 88 15
0 ... 4 ... 8 ... 14 T 0 ... 4 ... 8 ... 14 T 16 ... 16 ... 16 ... 16 dB 15 ... 16 ... 16 ... 16 dB > 23 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5 < 150 dBc 400 W (at 50 C ambient temperature) > 23 dB Typically: 25 dB > 10 dB

88 170
15
824 960 45
10
824 960 +45
10 3 0
dB
3 0
dB
7-16 Mechanical specifications Input Connector position Adjustment mechanism Weight

15.5
7-16
Horizontal Pattern
Vertical Pattern 0 14 electrical downtilt continuously adjustable
2 x 7-16 female Bottom 1x, Position bottom continuously adjustable 14 kg Frontal: Lateral: Rearside: 230 N (at 150 km/h) 130 N (at 150 km/h) 500 N (at 150 km/h) 200 km/h 1562 x 287 x 165 mm 1296 / 262 / 116 mm

85 170
Wind load
10
10
Max. wind velocity

dB
dB
3 0
3 0
Packing size Height/width/depth
Horizontal Pattern
Vertical Pattern 0 14 electrical downtilt continuously adjustable 27
XPol
XPol

Type No. Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth
870 960 X 90
739 655
870 960 MHz +45, 45 2 x 15.5 dBi Horizontal: Vertical: 15 dB > 25 dB > 32 dB 50 < 1.3 90 10
3 0
dB
90 170
Horizontal Pattern
10
< 150 dBc

10
870960 45 870960 +45
3 0
dB
7-16
7-16
28

Type No. Frequency range 806 894 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth +45, 45 2 x 15 dBi Horizontal: 85 Vertical: 10.5 18 dB > 25 dB > 30 dB 50 < 1.5 < 150 dBc
806 960 X 88
739 649
10 3 0 dB
88 165
Horizontal Pattern
10
10
600 W (at 50 C ambient temperature) 2 x 7-16 female Bottom or top 17.1 kg Frontal / Lateral / Rearside: 330 N / 200 N / 770 N 200 km/h 1936 / 262 / 116 mm
3 0
dB
806960 45
806960 +45
7-16
7-16

Type No. Frequency range 806 894 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth < 1.3 < 150 dBc
3
739 660
806960 880 960 MHz +45, 45 2 x 15.5 dBi Horizontal: Vertical: 18 dB > 25 dB > 30 dB 50 < 1.3
10
88 165
+45, 45 2 x 15 dBi Horizontal: 85 Vertical: 10.5
10 3 0 dB
88 10
6, fixed
Horizontal Pattern
10
dB
29
XPol
XPol

Type No. Frequency range 806 866 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Cross polar ratio Maindirection Sector Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 0 60 +45, 45 2 x 15 dBi Horizontal: 85 Vertical: 10.5 0.5 10
806 960 X 88 0 10
739 665
806960 824 894 MHz +45, 45 2 x 15 dBi Horizontal: 85 Vertical: 10.2 0.5 10 880 960 MHz +45, 45 2 x 15 dBi Horizontal: Vertical: 0.5 10 88 10
0 ... 4 ... 8 ... 10 T 0 ... 4 ... 8 ... 10 T 0 ... 4 ... 8 ... 10 T 16 ... 16 ... 17 ... 17 dB 16 ... 16 ... 17 ... 17 dB 16 ... 16 ... 18 ... 18 dB > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5 > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5 < 150 dBc 400 W (at 50 C ambient temperature) > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5

88 160
10
10
10 3 0 dB
3 0
dB
Horizontal Pattern
Vertical Pattern 0.5 10 electrical downtilt 806 960 45

85 160
10.2
806 960 +45
7-16 Mechanical specifications Input Connector position Adjustment mechanism Weight Wind load Frontal: Lateral: Rearside:
7-16
10
10 3 0
3 0
2 x 7-16 female Bottom 1x, Position bottom continuously adjustable 18 kg 330 N (at 150 km/h) 200 N (at 150 km/h) 770 N (at 150 km/h) 200 km/h 2262 x 287 x 165 mm 1996 / 262 / 116 mm
Horizontal Pattern
dB

85 160
10.5
dB
Max. wind velocity

10
10 dB
dB
3 0
3 0
Horizontal Pattern
30

Type No. Frequency range 806 894 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth +45, 45 2 x 16.5 dBi Horizontal: 85 Vertical: 8.5 18 dB > 25 dB > 30 dB 50 < 1.5 < 150 dBc
806 960 X 88
739 650
10 3 0 dB
88 165
Horizontal Pattern
10
600 W (at 50 C ambient temperature) 2 x 7-16 female Bottom or top 22.6 kg Frontal / Lateral / Rearside: 470 N / 280 N / 1040 N 200 km/h 2580 / 262 / 116 mm
3 0
dB
806960 45
806960 +45
7-16
7-16
31
XPol
XPol
A-Panel Dual Polarization Half-power Beam Width Fixed Electrical Downtilt

Type No. Frequency range 806 866 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Isolation Cross polar ratio Maindirection Sector Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 0 60 +45, 45 2 x 16.3 dBi Horizontal: 85 Vertical: 8.3 6 , fixed 16 dB > 25 dB > 32 dB > 23 dB > 14 dB 50 < 1.5
806 960 X 88 6
739 662
806960 824 894 MHz +45, 45 2 x 16.5 dBi Horizontal: 85 Vertical: 7.9 6 , fixed 16 dB > 25 dB > 32 dB > 23 dB > 14 dB 50 < 1.5 < 150 dBc 500 W (at 50 C ambient temperature) 880 960 MHz +45, 45 2 x 16.7 dBi Horizontal: Vertical: 6 , fixed 17 dB > 25 dB > 32 dB > 23 dB > 14 dB 50 < 1.3 88 7.5

88 165
7.5
10
10 3 0 dB
3 0
dB
Horizontal Pattern
Vertical Pattern 6 electrical downtilt 806 960 45 806 960 +45

85 160
7.9
7-16
7-16
10
10 3 0 dB
3 0
dB
Mechanical specifications Input Connector position Weight Wind load

8.3
Horizontal Pattern
2 x 7-16 female Bottom 21.4 kg Frontal: 470 N (at 150 km/h) Lateral: 280 N (at 150 km/h) Rearside: 1040 N (at 150 km/h) 200 km/h 2721 x 302 x 172 mm 2580 / 262 / 116 mm

85 160
Max. wind velocity

10
10 3 0 dB
3 0
dB
Horizontal Pattern
32

Type No. Frequency range 806 866 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression for first sidelobe above horizon Front-to-back ratio (180 30) Cross polar ratio Maindirection Sector Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 0 60 +45, 45 2 x 16 dBi Horizontal: 85 Vertical: 8.2 0 7
806 960 X 88 0 7
739 666
806960 824 894 MHz +45, 45 2 x 16.1 dBi Horizontal: Vertical: 0 7 85 8 880 960 MHz +45, 45 2 x 16.2 dBi Horizontal: Vertical: 0 7 88 7.5
0 ... 2 ... 4 ... 7 T 0 ... 2 ... 4 ... 7 T 0 ... 2 ... 4 ... 7 T 17 ... 17 ... 17 ... 17 dB 17 ... 17 ... 17 ... 17 dB 17 ... 17 ... 17 ... 17 dB Copolar: > 25 dB Total power: > 25 dB Typically: 25 dB > 15 dB > 30 dB 50 < 1.5 Copolar: > 25 dB Total power: > 25 dB Typically: 25 dB > 15 dB > 30 dB 50 < 1.5 < 150 dBc 400 W (at 50 C ambient temperature) Copolar: > 25 dB Total power: > 25 dB Typically: 25 dB > 15 dB > 30 dB 50 < 1.5

88 160
7.5
10
10 3 0 dB
3 0
dB
Horizontal Pattern

85 160
806 960 +45
7-16
8
7-16
10
Mechanical specifications Input Connector position Adjustment mechanism Weight Wind load 2 x 7-16 female Bottom 1x, Position bottom continuously adjustable 22 kg Frontal: 470 N (at 150 km/h) Lateral: 280 N (at 150 km/h) Rearside: 1040 N (at 150 km/h) 200 km/h 2846 x 287 x 165 mm 2580 / 262 / 116 mm
dB
10 3 0 dB
3 0
Horizontal Pattern

85 160
8.2
Max. wind velocity

10
10 dB
dB
3 0
3 0
Horizontal Pattern
XPol
XPol
Compact Panel Dual Polarization Half-power Beam Width Fixed Electrical Downtilt
XPol C-Panel 806960 65 15.5dBi 0T
Type No. Frequency range 806 866 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Sidelobe suppression for: first sidelobe above horizon sector 0 30 above horizon Front-to-back ratio, copolar Isolation Crosspolar ratio Maindirection Sector Sector Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 0 30 60 +45, 45 2 x 14.7 dBi Horizontal: 67 Vertical: 15.5 > 15 dB > 15 dB > 30 dB > 30 dB > 20 dB > 19 dB > 11 dB 50 < 1.5
806 960 X 65 0
800 10202
806960 824 894 MHz +45, 45 2 x 15 dBi Horizontal: 66 Vertical: 14.8 > 15 dB > 15 dB > 30 dB > 30 dB > 20 dB > 19 dB > 11 dB 50 < 1.4 < 150 dBc 500 W (at 50 C ambient temperature) 880 960 MHz +45, 45 2 x 15.3 dBi Horizontal: Vertical: > 14 dB > 14 dB > 30 dB > 30 dB > 20 dB > 20 dB > 11 dB 50 < 1.3 64 14

120 64
14
10 3 0
10
dB
3 0
Horizontal Pattern
Vertical Pattern 806 960 45 806 960 +45

124 66
dB
7-16
14.8
7-16
10 3 0
10
dB
3 0
dB
Mechanical specifications Input Connector position Weight 2 x 7-16 female Bottom 6.5 kg Frontal: Lateral: Rearside: 220 N (at 150 km/h) 140 N (at 150 km/h) 490 N (at 150 km/h) 200 km/h 1422 x 272 x 160 mm 1294 / 259 / 112 mm
Horizontal Pattern
Vertical Pattern

127 67 15.5
Wind load
10 3 0
10
Max. wind velocity Packing size Height/width/depth

dB
dB
3 0
Horizontal Pattern
Vertical Pattern
34
XPol C-Panel 806960 65 17dBi 0T
Type No. Frequency range 806 866 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Sidelobe suppression for: first sidelobe above horizon sector 030 above horizon Front-to-back ratio, copolar Isolation Cross polar ratio Maindirection Sector Sector Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 0 30 60 +45, 45 2 x 16.5 dBi Horizontal: 68 Vertical: 10.2 > 17 dB > 15 dB > 30 dB > 30 dB > 20 dB > 18 dB > 12 dB 50 < 1.5
806 960 X 65 0
800 10203
806960 824 894 MHz +45, 45 2 x 16.7 dBi Horizontal: Vertical: > 17 dB > 15 dB > 30 dB > 30 dB > 20 dB > 18 dB > 12 dB 50 < 1.4 < 150 dBc 500 W (at 50 C ambient temperature) 66 10 880 960 MHz +45, 45 2 x 17 dBi Horizontal: 64 Vertical: 9.3 > 17 dB > 15 dB > 30 dB > 30 dB > 20 dB > 18 dB > 12 dB 50 < 1.3

120 64 9.3
10 3 0
10
dB
3 0
Horizontal Pattern
Vertical Pattern

127 66 10
dB
806 960 45
806 960 +45
10 3 0
10
7-16
dB
7-16
dB
3 0
Mechanical specifications Input Connector position 2 x 7-16 female Rearside 9.5 kg Frontal: Lateral: Rearside: 340 N (at 150 km/h) 220 N (at 150 km/h) 750 N (at 150 km/h) 200 km/h 2062 x 272 x 160 mm 1934 / 259 / 112 mm
Horizontal Pattern
Vertical Pattern

130 68
10.2
Weight Wind load
10 3 0
10
dB
3 0
Horizontal Pattern
Vertical Pattern
dB
35
XPol
XPol
Type No. Frequency range 806 866 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Sidelobe suppression for: first sidelobe above horizon sector 030 above horizon Front-to-back ratio, copolar Isolation Cross polar ratio Maindirection Sector Sector Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 0 30 60 +45, 45 2 x 17.4 dBi Horizontal: 68 Vertical: 8.5 > 15 dB > 15 dB > 30 dB > 30 dB > 18 dB > 16 dB > 10 dB 50 < 1.5
806 960 X 65 0
800 10204
806960 824 894 MHz +45, 45 2 x 17.6 dBi Horizontal: 66 Vertical: 8.3 > 15 dB > 15 dB > 30 dB > 30 dB > 19 dB > 16 dB > 10 dB 50 < 1.4 < 150 dBc 500 W (at 50 C ambient temperature) 880 960 MHz +45, 45 2 x 17.8 dBi Horizontal: 64 Vertical: 7.8 > 15 dB > 14 dB > 30 dB > 30 dB > 20 dB > 17 dB > 11 dB 50 < 1.3

120 64 7.8
10 3 0
10
dB
3 0
Horizontal Pattern

127 66 8.3
dB
7-16
7-16
10 3 0
10
3 0
Mechanical specifications Input Connector position Weight Wind load Frontal: Lateral: Rearside: 2 x 7-16 female Rearside 11 kg 400 N (at 150 km/h) 260 N (at 150 km/h) 890 N (at 150 km/h) 200 km/h 2382 x 272 x 160 mm 2254 / 259 / 112 mm
dB
Horizontal Pattern
Vertical Pattern

130 68 8.5
dB
Max. wind velocity

10 3 0 0 10
Packing size
dB
dB
Height/width/depth
Horizontal Pattern
Vertical Pattern
36
Type No. Frequency range 806 866 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt Sidelobe suppression for: first sidelobe above horizon sector 030 above horizon Front-to-back ratio, copolar Isolation Cross polar ratio Maindirection Sector Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 0 60 +45, 45 2 x 14.5 dBi Horizontal: Vertical: 6, fixed > 14 dB > 14 dB > 30 dB > 30 dB Tpyically: > 20 dB Typically: > 10 dB 50 < 1.3 66 16
806 960 X 65 6
800 10207
806960 824 894 MHz +45, 45 2 x 14.7 dBi Horizontal: 65 Vertical: 15.7 6, fixed > 15 dB > 15 dB > 30 dB > 30 dB Typically: > 20 dB Typically: > 10 dB 50 < 1.3 < 150 dBc 500 W (at 50 C ambient temperature) 880 960 MHz +45, 45 2 x 15 dBi Horizontal: 63 Vertical: 14.6 6, fixed > 16 dB > 14 dB > 30 dB > 30 dB Typically: > 20 dB Typically: > 10 dB 50 < 1.3

118 63 14.6
10 3 0
10
dB
3 0
Horizontal Pattern

123 65
dB
7-16
15.7
7-16
10 3 0
10
dB
3 0
dB
Mechanical specifications Input Connector position 2 x 7-16 female Bottom 6.5 kg Frontal: Lateral: Rearside: 220 N (at 150 km/h) 140 N (at 150 km/h) 490 N (at 150 km/h) 200 km/h 1422 x 272 x 160 mm 1294 / 259 / 112 mm
Horizontal Pattern

125 66
16
Weight Wind load
Max. wind velocity

10 3 0
0 10
Packing size
dB
dB
Height/width/depth
Horizontal Pattern
Vertical Pattern 6 electrical downtilt 37
XPol
38
Vertical Polarization 800/900

Type Type No. Height [mm] 500 Connector position bottom Page
VPol Panel
870960
20
16.5dBi
735 727
40
VPol ParPanel
870960
36
20dBi
K 73 45 64 7
2250
bottom
41
VPol LogPer
790960
51
12dBi
K 73 22 67
300
bottom
42
VPol Panel VPol Panel VPol Panel VPol Panel VPol Panel VPol Panel VPol Panel VPol Panel
860960 870960 806960 870960 870960 870960 870960 870960
65 65 65 65 65 65 65 65
9dBi 15.5dBi 15.5dBi 17dBi 17dBi 18dBi 18.5dBi 18.5dBi
730 677 730 368 732 691 730 691 737 547 739 854 730 376 732 689
264 1294 1294 1934 1934 2254 2574 2574
bottom or top bottom bottom rearside rearside rearside rearside bottom
43 43 44 44 45 45 46 46
6T
9T
6T
VPol F-Panel VPol F-Panel VPol Panel VPol Panel
872960 872960 870960 870960
90 90 90 90
7.5dBi 10dBi 15.5dBi 17dBi
736 854 736 855 732 967 730 378
262 502 1934 2574
bottom or top bottom or top rearside rearside
47 47 48 48
VPol Panel
870960
105
16.5dBi
730 380
2574
rearside
49
VPol Panel VPol Panel
870960 870960
120 120
15.5dBi 16dBi
739 856 730 382
2254 2574
rearside rearside
50 50
Additional versions on request
39
GSM 900 VPol
Summary Directional Antennas Vertical Polarization GSM 900 / GSM-R / GSM 850 / CDMA 800
Panel Vertical Polarization Half-power Beam Width
870 960 V 20
VPol Panel 870960 20 16.5dBi

Type No. Input Frequency range VSWR Gain Impedance Polarization Front-to-back-ratio Half-power Beam Width Max. power Weight Wind load
735 727
7-16 female 870 960 MHz < 1.3 16.5 dBi 50 Vertical > 24 dB H-plane: 20/ E-plane: 33 500 W (at 50 C ambient temperature) 10 kg Frontal: 500 N (at 150 km/h) Lateral: 110 N (at 150 km/h) Rearside: 715 N (at 150 km/h) 230 km/h 1062 x 562 x 275 mm 492 / 992 / 190 mm Radiator: Aluminum. Reflector screen: Weather-proof aluminum. Radome: Fiberglass, colour: White. All screws and nuts: Stainless steel. Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. All metal parts of the antenna as well as the inner conductor are DC grounded.
Max. wind velocity Packing size Height/width/depth Material:
Ice protection:
Grounding:
Accessories (order separately)

Type No. K K K K 61 61 61 61 14 14 14 14 02 03 04 05 Description 2 2 2 2 clamps clamps clamps clamps Remarks Mast: 60 115 mm diameter Mast: 115 210 mm diameter Mast: 210 380 mm diameter Mast: 380 521 mm diameter
20
33
10 dB
10
3 0
3 0
Horizontal Pattern
Vertical Pattern
40
dB
K 61 14 03
VPol ParPanel 870960 36 20dBi

Type No. Input Frequency range VSWR Gain Impedance Polarization Front-to-back ratio Half-power Beam Width Max. power Weight Wind load
K 73 45 64 7
7-16 female 870 960 MHz < 1.3 20 dBi 50 Vertical > 30 dB H-plane: 36/ E-plane: 8 500 W (at 50 C ambient temperature) 30 kg Frontal: 950 N (at 150 km/h) Lateral: 600 N (at 150 km/h) Rearside: 950 N (at 150 km/h) 200 km/h 2420 x 640 x 465 mm 2250 / 591 / 406 mm Radiator: Weather-proof aluminum. Reflector screen: Weather-proof aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel.
429
Ice protection:
Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. All metal parts of the antenna are DC grounded. The inner conductor is coupled capacitively.
Grounding:
2250
2300

Type No. 733 736 K 61 14 03 K 61 14 04 K 61 14 05 733 695 Description 2 2 2 2 1 clamps clamps clamps clamps downtilt kit Remarks Mast: 50 125 mm diameter Mast: 115 210 mm diameter Mast: 210 380 mm diameter Mast: 380 521 mm diameter Downtilt angle: 0 10 Use the downtilt kit together with 2 clamps suitable for the mast diameter.
11
13 591 140
406
36
10
10
dB
3 0
3 0
Horizontal Pattern
Vertical Pattern K 61 14 03
dB
2360
41
VPol
Parabolic Panel Vertical Polarization Half-power Beam Width
870 960 V 36
VPol
Logarithmic periodic Vertical Polarization Half-power Beam Width
790 960 V 51
VPol LogPer 790960 51 12dBi

Type No. Input Frequency range VSWR Gain Impedance Polarization Side-lobe supression Front-to-back ratio Half-power Beam Width Max. power Weight Wind load
K 73 22 67
7-16 female 790 960 MHz < 1.4 12 dBi 50 Vertical > 25 dB > 30 dB H-plane: 51/ E-plane: 45 500 W (at 50 C ambient temperature) 6.3 kg Frontal: 20 N (at 150 km/h) Lateral: 260 N (at 150 km/h) Rearside: 30 N (at 150 km/h) 200 km/h 1000 x 360 x 175 mm 300 / 155 / 785 mm Radiator: Weather-proof aluminum. Reflector screen: Weather-proof aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. The antenna can be mounted on tubular mast with a diameter of 30 70 mm with supplied clamps. Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. All metal parts of the antenna as well as the inner conductor are DC grounded.
Mounting:
Ice protection:
Grounding:
51
45
10
10
dB
3 0
3 0
Horizontal Pattern
Vertical Pattern
42
dB
VPol Panel 860960 65 9dBi

Type No. Frequency range Polarization Gain Half-power beam width Front-to-back ratio Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth
730 677
860 960 MHz Vertical 9 dBi
10
120
65
H-plane: 65 E-plane: 70 > 25 dB (890 960 MHz) > 20 dB (860 890 MHz) 50 < 1.3 < 150 dBc 350 W (at 50 C ambient temperature) N female Bottom or top 1.2 kg Frontal / Lateral / Rearside: 40 N / 25 N / 90 N 230 km/h 264 / 258 / 103 mm
3 0
Horizontal Pattern
dB
70
10
3 0
Vertical Pattern

730 368
870 960 MHz Vertical 15.5 dBI
10
dB
120
65
H-plane: 65 E-plane: 13 > 25 dB 50 < 1.3 < 150 dBc 500 W (at 50 C ambient temperature) 7-16 female Bottom 6 kg
3 0
Horizontal Pattern
dB
13
10
Vertical Pattern
dB
43
VPol
Eurocell Panel Vertical Polarization Half-power Beam Width
900 V 65
VPol

VPol Panel 806960 65 15.5dBi 6T
Type No. Frequency range Polarization Gain Half-power beam width Electrical downtilt Front-to-back ratio Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth
800/900 V 65
732 691
806 960 MHz Vertical 15.5 dBi
10
120
65
H-plane: 65 E-plane: 13 6, fixed > 25 dB 50 < 1.3 < 150 dBc
3 0
Horizontal Pattern
dB
13
500 W (at 50 C ambient temperature) 7-16 female Bottom

3 10
6 kg Frontal / Lateral / Rearside: 220 N / 140 N / 490 N 200 km/h 1294 / 258 / 103 mm

730 691
10
dB
120
65
H-plane: 65 E-plane: 8.5 > 25 dB 50 < 1.3 < 150 dBc 500 W (at 50 C ambient temperature)
3 0
Horizontal Pattern
dB
8.5
7-16 female Rearside 9 kg

3 10
Vertical Pattern
44
dB
VPol Panel 870960 65 17dBi 9T

737 547
10
120
65
H-plane: 65 E-plane: 8.5 9, fixed > 25 dB 50 < 1.3 < 150 dBc 500 W (at 50 C ambient temperature) 7-16 female Rearside
3 0
Horizontal Pattern
dB
9
10
9 kg Frontal / Lateral / Rearside: 340 N / 220 N / 750 N 200 km/h 1934 / 258 / 103 mm

739 854
10
dB
120
65
3 0
Horizontal Pattern
dB
7.5
7-16 female Rearside 10.5 kg

3 10
Vertical Pattern
dB
45
VPol
870 960 V 65
VPol

870 960 V 65
730 376
10
120
65
3 0
Horizontal Pattern
dB
6.5

3 10
Vertical Pattern
VPol Panel 870960 65 18.5dBi 6T

732 689
10
dB
120
65
H-plane: 65 E-plane: 6.5 6, fixed > 25 dB 50 < 1.3 < 150 dBc 500 W (at 50 C ambient temperature) 7-16 female Rearside
3 0
Horizontal Pattern
dB
6.5
10
12 kg
0
46
dB
VPol F-Panel 872960 90 7.5dBi

736 854
872 960 MHz Vertical 7.5 dBi H-plane: 90 E-plane: 70 > 20 dB 50 < 1.5 < 140 dBc
10 3 0
dB
90 180
Horizontal Pattern
70
350 W (at 50 C ambient temperature) N female Bottom or top 1.5 kg

3 10
Frontal / Lateral / Rearside: 45 N / 20 N / 60 N (at 150 km/h) 200 km/h 262 / 155 / 49 mm
Vertical Pattern
VPol F-Panel 872960 90 10dBi

736 855
872 960 MHz Vertical 10 dBi H-plane: 90 E-plane: 36 > 20 dB 50 < 1.4 < 150 dBc 400 W (at 50 C ambient temperature) 7-16 female Bottom or top 2.3 kg Frontal / Lateral / Rearside: 90 N / 40 N / 110 N 200 km/h 502 / 155 / 49 mm
10 dB
10 3 0
dB
dB
90 180
Horizontal Pattern
36
3 0
Vertical Pattern
47
VPol
F-Panel Vertical Polarization Half-power Beam Width
872 960 V 90
VPol

870 960 V 90
732 967
870 960 MHz Vertical 15.5 dBi H-plane: 90 E-plane: 8.5 > 23 dB 50 < 1.3 < 150 dBc 500 W (at 50 C ambient temperature)
10 3 0
dB
90 180
Horizontal Pattern
8.5

3 10
Frontal / Lateral / Rearside: 340 N / 220 N / 750 N (at 150 km/h) 200 km/h 1934 / 258 / 103 mm
Vertical Pattern

730 378
870 960 MHz Vertical 17 dBi H-plane: 90 E-plane: 6.5 > 23 dB 50 < 1.3 < 150 dBc 500 W (at 50 C ambient temperature)
10 3 0
dB
dB
90 180
Horizontal Pattern
6.5

3 10
Vertical Pattern
48
dB

730 380
870 960 MHz Vertical 16.5 dBi H-plane: 105 E-plane: 6.5 > 22 dB 50 < 1.3 < 150 dBc 500 W (at 50 C ambient temperature)
195
105
3 0
Horizontal Pattern
dB
6.5

3 10
Vertical Pattern
dB
49
VPol
870 960 V 105
VPol

870 960 V 120
739 856
10
120
215
3 0
Horizontal Pattern
dB
7.5
7-16 female Rearside 10.5 kg

3 10
Vertical Pattern

730 382
10
215
3 0
Horizontal Pattern
dB
dB
120
6.5

3 10
Vertical Pattern
50
dB
Summary Directional Antennas Dual Polarization + 45/ 45 GSM 1800 / GSM 1900 / PCS
GSM 1800 XPol
Dual Polarization + 45/ 45 1800/1900

Type Type No. Height [mm] 982 1942 Connector position bottom bottom Page
XPol F-Panel XPol F-Panel
17101880 17101880
33 33
19.5dBi 22dBi
2T 2T
739 927 741 623
52 52
XPol F-Panel XPol F-Panel XPol F-Panel XPol F-Panel XPol F-Panel XPol F-Panel
17101880 17101880 17101880 17101880 17101990 17101990
65 65 65 65 65 65
15.5dBi 15.5dBi 15dBi 18dBi 18dBi 19.5dBi
6T 12T
739 490 739 491 741 264 739 494 739 495 739 498
662 662 662 1302 1302 1942
bottom or top bottom bottom bottom or top bottom bottom
53 53 54 54 55 55
2T 2T
XPol F-Panel XPol F-Panel XPol F-Panel XPol F-Panel
17101990 17101880 17101880 17101880
90 90 90 90
8dBi 16.5dBi 16.5dBi 17.5dBi 2T 6T 2T
739 695 739 707 739 708 739 710
174 1302 1302 1902
bottom or top bottom bottom bottom
56 57 57 58
51
F-Panel Dual Polarization Half-power Beam Width Fixed Electrical Downtilt

XPol F-Panel 17101880 33 19.5dBi 2T
Type No. Frequency range Polarization Gain Half-power beam width Copolar Electrical tilt Sidelobe suppression Front-to-back ratio, copolar Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth +45 Horizontal: Vertical:
17101880 X 33 2
739 927
1710 1880 MHz +45, 45 2 x 19.5 dBi
10
33
33 9
45 Horizontal: Vertical:
33 9
3 0
2, fixed above horizon for first sidelobe better or equal 14 dB below maximum gain > 30 dB > 30 dB 50 < 1.5 < 150 dBc 200 W (at 50 C ambient temperature) 2 x 7-16 female Bottom 7 kg Frontal / Lateral / Rearside: 260 N / 95 N / 370 N 200 km/h 982 / 262 / 59 mm
Horizontal Pattern
dB
10 3 0 dB
Vertical Pattern 2 electrical downtilt first null-fill below horizon better or equal 25 dB below maximum gain
17101880 45 17101880 +45
7-16
7-16
XPol F-Panel 17101880 33 22dBi 2T

Type No. Frequency range Polarization Gain Half-power beam width Copolar Electrical tilt Sidelobe suppression Front-to-back ratio, copolar Isolation Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth 52 +45 Horizontal: Vertical:
741 623
1710 1880 MHz +45, 45 2 x 22 dBi
10
33
33 5
45 Horizontal: Vertical:
33 5
3 0
2, fixed above horizon for first sidelobe better or equal 14 dB below maximum gain > 30 dB > 30 dB 50 < 1.5 < 150 dBc
Horizontal Pattern
dB
5
10
dB
F-Panel Dual Polarization Half-power Beam Width

XPol F-Panel 17101880 65 15.5dBi
Type No. Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Front-to-back ratio, copolar Isolation, between ports Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth
17101880 X 65
1710 1880 MHz +45, 45 2 x 15.5 dBi

10
120
65
65 13
3 0
Horizontal Pattern
< 150 dBc

13
200 W (at 50 C ambient temperature) 2 x 7-16 female Bottom or top

3 10
3.5 kg
0
Vertical Pattern
17101880 45
dB
dB
17101880 +45
7-16
7-16

Type No. Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt Front-to-back ratio, copolar Isolation, between ports Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth
739 491
1710 1880 MHz +45, 45 2 x 15.5 dBi
10
120
65
Horizontal: Vertical: 6, fixed > 30 dB > 30 dB 50 < 1.5
65 14
3 0
Horizontal Pattern
< 150 dBc 200 W (at 50 C ambient temperature) 2 x 7-16 female

3 10
dB
14
Bottom 3.5 kg Frontal / Lateral / Rearside: 150 N / 55 N / 120 N 200 km/h 662 / 155 / 49 mm
dB
53
XPol
739 490

XPol Type No. Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt Front-to-back ratio, copolar Isolation, between ports Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth
17101880 X 65
741 264
1710 1880 MHz +45, 45 2 x 15 dBi
10
120
65
Horizontal: Vertical: 12, fixed > 30 dB > 30 dB 50 < 1.4
65 14
3 0
Horizontal Pattern
< 150 dBc 200 W (at 50 C ambient temperature) 2 x 7-16 female

3 10
dB
14
Bottom 3.5 kg Frontal / Lateral / Rearside: 150 N / 55 N / 120 N 200 km/h 662 / 155 / 49 mm
17101880 45
dB
17101880 +45
7-16
7-16
XPol F-Panel 17101880 65 18dBi

Type No. Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Front-to-back ratio, copolar Isolation, between ports Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth
739 494
1710 1880 MHz +45, 45 2 x 18 dBi
10
120
65
65 6.5
3 0
Horizontal Pattern
< 150 dBc

6.5
200 W (at 50 C ambient temperature) 2 x 7-16 female Bottom or top

3 10
6 kg
0
Vertical Pattern
54
dB
dB

Type No. Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Isolation, between ports Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth
17101990 X 65
1710 1990 MHz +45, 45 2 x 18 dBi

10
120
65
Horizontal: Vertical: 2, fixed 14 dB > 30 dB > 30 dB 50
65 7
3 0
Horizontal Pattern
dB
< 1.4 (1710 1880 MHz) < 1.5 (1880 1990 MHz) < 150 dBc
7
10
17101990 45 17101990 +45
dB
7-16
7-16

739 498
1710 1990 MHz +45, 45 2 x 19.5 dBi (1880 1990 MHz) 2 x 19 dBi (1710 1880 MHz) Horizontal: Vertical: 2, fixed 14 dB > 30 dB > 30 dB 50 < 1.5 < 150 dBc
3 10 10
120
65
65 5
3 0
Horizontal Pattern
dB
200 W (at 50 C ambient temperature) 2 x 7-16 female Bottom 8.5 kg Frontal / Lateral / Rearside: 480 N / 180 N / 380 N 200 km/h 1942 / 155 / 49 mm
dB
55
XPol
739 495

XPol F-Panel 17101990 90 8dBi
XPol Type No. Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Front-to-back ratio, copolar Isolation, between ports Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth
1710 1990 X 90
739 695
1710 1990 MHz +45, 45 2 x 8 dBi Horizontal: Vertical: > 20 dB > 30 dB 50 < 1.4 < 150 dBc 200 W (at 50 C ambient temperature) 2 x 7-16 female Bottom or top
3 10
90 170
90 55
3 0
Horizontal Pattern
dB
55
3 kg
0
Vertical Pattern
17101990 45
dB
17101990 +45
7-16
7-16
56

17101880 X 90
90 170
1710 1880 MHz +45, 45 2 x 16.5 dBi Horizontal: Vertical: 2, fixed 14 dB > 27 dB > 30 dB 50 < 1.4 < 150 dBc 200 W (at 50 C ambient temperature) 2 x 7-16 female Bottom 6 kg Frontal / Lateral / Rearside: 130 N / 110 N / 310 N 200 km/h 1302 / 155 / 69 mm 90 7
3 0
Horizontal Pattern
dB
7
10
3 0
17101880 45 17101880 +45
dB
7-16
7-16

739 708
1710 1880 MHz +45, 45 2 x 16.5 dBi Horizontal: Vertical: 6, fixed 14 dB > 27 dB > 30 dB 50 90 7
3 0
dB
90 170
Horizontal Pattern
< 1.4 < 150 dBc 200 W (at 50 C ambient temperature) 2 x 7-16 female Bottom 6 kg Frontal / Lateral / Rearside: 130 N / 110 N / 310 N 200 km/h 1302 / 155 / 69 mm 57
10
3 0
dB
XPol
739 707
F-Panel Dual Polarization Half-power Beam Width Fixed Electrical Downtilt

XPol Type No. Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Isolation, between ports Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth
17101880 X 90 2
739 710
1710 1880 MHz +45, 45 2 x 17.5 dBi Horizontal: Vertical: 2, fixed 14 dB > 25 dB > 30 dB 50 < 1.4 < 150 dBc 200 W (at 50 C ambient temperature) 2 x 7-16 female Bottom 9 kg Frontal / Lateral / Rearside: 190 N / 160 N / 470 N 200 km/h 1902 / 155 / 69 mm
10
90 170
90 5
3 0
Horizontal Pattern
dB
3 0
17101880 45 17101880 +45
dB
7-16
7-16
58
Summary Directional Antennas Dual-band GSM 900 / GSM 1800 / GSM 1900 / PCS
Dual-band 800/900 1800/2000 Dual Polarization + 45/ 45
Type Type No. Height [mm] 656 1296 1296 1296 1936 1936 2580 2580 2580 2580 2580 Page
XXPol A-Panel XXPol A-Panel XXPol A-Panel XXPol A-Panel XXPol A-Panel XXPol A-Panel XXPol A-Panel XXPol A-Panel XXPol A-Panel XXPol A-Panel XXPol A-Panel
870960/17101880 870960/17101880 870960/17101880 824960/17101880 870960/17101880 870960/17101880 870960/17101880 870960/17101880 870960/17101880 870960/17101880 870960/17101880
C C C C
65/65 65/60 65/60 65/63 65/60 65/60 65/60 65/60 65/60 65/60 65/ 60
12.5/13dBi 15/16.5dBi 15/17dBi 14.5/16.5dBi 17/18dBi 17/18.5dBi 18/19dBi 18/19.5dBi 17.5/17.5dBi 17.5/18dBi 17/18dBi 6T 6T 28T/2T
741 316 741 320 741 326 742 151 741 322 741 327 741 324 741 328 741 336 741 344 742 047
60 61 62 63 64 65 66 67 68 69 70
GSM 1800 XXPol 59
010T/2T
C C
Connector position: Bottom
Dual-band A-Panel Dual Polarization Half-power Beam Width Integrated Combiner
870 960 X 65
1710 1880 X 65 C
XXPol A-Panel 870960/17101880 C 65/ 65 12.5/13dBi

Type No. Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Front-to-back ratio, copolar Isolation, between ports Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input
741 316
900 870 960 870 960 MHz +45, 45 2 x 12.5 dBi Horizontal: Vertical: > 30 dB > 30 dB 50 < 1.5 < 150 dBc 65 28 1800 17101880 1710 1880 MHz +45, 45 2 x 13 dBi Horizontal: Vertical: > 30 dB > 30 dB 50 < 1.5 < 150 dBc 60 19
250 W 150 W (at 50 C ambient temperature) The insertion loss is included in the given antenna gain values.
Integrated combiner
870 960 +45/ 45 Polarization

65 28
120
1710 1880 45 C 7-16

dB
870 960 45
870 960 +45 C
1710 1880 +45
10
10
7-16
dB
3 0
3 0
Horizontal Pattern
Vertical Pattern Mechanical specifications
Input Connector position* Weight
2 x 7-16 female Bottom or top 7 kg Frontal: Lateral: Rearside: 110 N (at 150 km/h) 60 N (at 150 km/h) 240 N (at 150 km/h) 200 km/h 782 x 287 x 165 mm 656 / 262 / 116 mm
120
65 19
Wind load
Max. wind velocity

10 10
Packing size
dB dB
3 0
3 0
Height/width/depth
Horizontal Pattern
Vertical Pattern
* Inverted mounting: Connector position top: Change drain hole screw.
60
870 960 X 65
1710 1880 X 60 C
XXPol A-Panel 870960/17101880 C 65/ 60 15/16.5dBi

Type No. Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Front-to-back ratio, copolar Isolation, between ports Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input XXPol 1710 1880 45
14
741 320
900 870 960 870 960 MHz +45, 45 2 x 15 dBi Horizontal: Vertical: > 30 dB > 30 dB 50 < 1.5 < 150 dBc 65 14 1800 17101880 1710 1880 MHz +45, 45 2 x 16.5 dBi Horizontal: Vertical: > 30 dB > 30 dB 50 < 1.5 < 150 dBc 60 8
Integrated combiner

65
120
870 960 45 C
870 960 +45 C
1710 1880 +45
10
10
7-16
dB
7-16
dB
3 0
3 0
Horizontal Pattern
115
60
8
Wind load
Max. wind velocity

10
10
Packing size
dB
dB
3 0
3 0
Height/width/depth
Horizontal Pattern
Vertical Pattern
61
Dual-band A-Panel Dual Polarization Half-power Beam Width
870 960 X 65
1710 1880 X 60
XXPol A-Panel 870960/17101880 65/ 60 15/17dBi

Type No. XXPol Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Front-to-back ratio, copolar Isolation, between ports
741 326
900 870 960 870 960 MHz +45, 45 2 x 15 dBi Horizontal: Vertical: > 30 dB 65 14 1800 17101880 1710 1880 MHz +45, 45 2 x 17 dBi Horizontal: Vertical: > 30 dB 60 8
> 30 dB (GSM 900 GSM 900)1 > 30 dB (GSM 1800 GSM 1800) > 30 dB (GSM 900 GSM 1800) 50 < 1.5 < 150 dBc 50 < 1.5 < 150 dBc
Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input
400 W 200 W (at 50 C ambient temperature)

65
14
120
1710 1880 45
870 960 45
870 960 +45
1710 1880 +45
7-16
10
10
7-16
7-16
7-16
dB
3 0
3 0
Horizontal Pattern
dB
115
60
8
Wind load
Max. wind velocity

10
10
Packing size
dB
dB
3 0
3 0
Height/width/depth
Horizontal Pattern
Vertical Pattern
62
Dual-band A-Panel Dual Polarization Half-power Beam Width Adjust. Electr. Downtilt Integrated Combiner
824 960 X 65 010
1710 1880 X 63 2 C
XXPol A-Panel 824960/17101880 C 65/63 14.5/16.5dBi 010T/2T

Type No. Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Cross polar ratio Maindirection Sector 0 60 XXPol 824 960 45 C 7-16
10 10
dB dB
742 151
824960 824 880 MHz 880 960 MHz +45, 45 2 x 14 dBi Horizontal: 69 Vertical: 14.5 010 +45, 45 2 x 14.5 dBi Horizontal: 65 Vertical: 14 010 17101880 1710 1880 MHz +45, 45 2 x 16.5 dBi Horizontal: 63 Vertical: 8.5 2 16 dB > 27 dB Typically: 20 dB > 10 dB > 30 dB 50 < 1.5 < 150 dBc
0 ... 6 ... 10T 0 ... 6 ... 10T 16 ... 13 ... 12 dB 17 ... 15 ... 13 dB > 30 dB Typically: 20 dB > 10 dB > 30 dB Typically: 20 dB > 10 dB
Isolation, between ports Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input
> 30 dB 50 < 1.5 < 150 dBc
Integrated combiner

65 14
1710 1880 45
824 960 +45 C
1710 1880 +45
130
7-16
3 0
3 0
Horizontal Pattern
Vertical Pattern 010 electrical downtilt continuously adjustable
Mechanical specifications Input Connector position Adjustment mechanism Weight Wind load 2 x 7-16 female Bottom 1x, Position bottom continuously adjustable 14 kg Frontal: Lateral: Rearside: 230 N (at 150 km/h) 130 N (at 150 km/h) 500 N (at 150 km/h) 200 km/h 1422 x 287 x 165 mm 1296 / 262 / 116 mm
120
63
8.5
10
Max. wind velocity

10
dB
3 0
3 0
dB
Horizontal Pattern
870 960 X 65
1710 1880 X 60 C
XXPol A-Panel 870960/17101880 C 65/ 60 17/18dBi

Type No. XXPol Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Isolation, between ports Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input
741 322
900 870 960 870 960 MHz +45, 45 2 x 17 dBi Horizontal: 65 Vertical: 9.5 > 15 dB > 30 dB > 30 dB 50 < 1.5 < 150 dBc 1800 17101880 1710 1880 MHz +45, 45 2 x 18 dBi Horizontal: 60 Vertical: 5.5 > 15 dB > 30 dB > 30 dB 50 < 1.5 < 150 dBc
Integrated combiner

65
9.5
120
1710 1880 45 C
870 960 45
870 960 +45 C
1710 1880 +45
10
10
dB
3 0
3 0
dB
7-16
7-16
Horizontal Pattern
115
60 5.5
Wind load
Max. wind velocity

10 10
Packing size
dB dB
3 0
3 0
Height/width/depth
Horizontal Pattern
Vertical Pattern
64
870 960 X 65
1710 1880 X 60
XXPol A-Panel 870960/17101880 65/ 60 17/18.5dBi

Type No. Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Isolation, between ports > 30 dB XXPol 1710 1880 45
10
741 327
900 870 960 870 960 MHz +45, 45 2 x 17 dBi Horizontal: 65 Vertical: 9.5 > 15 dB > 30 dB 1800 17101880 1710 1880 MHz +45, 45 2 x 18.5 dBi Horizontal: 60 Vertical: 5.5

65
9.5
120
870 960 45
870 960 +45
1710 1880 +45
10
dB
3 0
3 0
dB
7-16 Vertical Pattern
7-16
7-16
7-16
Horizontal Pattern
Mechanical specifications
115
60 5.5
Wind load
Max. wind velocity

10 10
Packing size
dB dB
3 0
3 0
Height/width/depth
Horizontal Pattern
Vertical Pattern
65
870 960 X 65
1710 1880 X 60 C
XXPol A-Panel 870960/17101880 C 65/ 60 18/19dBi

Type No. XXPol Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Front-to-back ratio, copolar Isolation, between ports Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input
741 324
900 870 960 870 960 MHz +45, 45 2 x 18 dBi Horizontal: Vertical: > 30 dB > 30 dB 50 < 1.5 < 150 dBc 65 7 1800 17101880 1710 1880 MHz +45, 45 2 x 19 dBi Horizontal: Vertical: > 30 dB > 30 dB 50 < 1.5 < 150 dBc 60 4
Integrated combiner

65
7
120
10
1710 1880 45
10
dB
870 960 45 C
870 960 +45 C
1710 1880 +45
3 0
3 0
dB
Horizontal Pattern
Vertical Pattern
7-16 Mechanical specifications
7-16
2 x 7-16 female Bottom or top 25 kg Frontal: 470 N (at 150 km/h) Lateral: 280 N (at 150 km/h) Rearside: 1040 N (at 150 km/h) 200 km/h 2692 x 287 x 165 mm 2580 / 262 / 116 mm
115
60 4
Wind load
Max. wind velocity

10 10
Packing size
dB dB
3 0
3 0
Height/width/depth
Horizontal Pattern
Vertical Pattern
66
870 960 X 65
1710 1880 X 60
XXPol A-Panel 870960/17101880 65/ 60 18/19.5dBi

Type No. Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Front-to-back ratio, copolar Isolation, between ports XXPol 1710 1880 45
10
741 328
900 870 960 870 960 MHz +45, 45 2 x 18 dBi Horizontal: Vertical: > 30 dB 65 7 1800 17101880 1710 1880 MHz +45, 45 2 x 19.5 dBi Horizontal: Vertical: > 30 dB 60 4

65
7
120
870 960 45
870 960 +45
1710 1880 +45
10
dB
3 0
3 0
dB
7-16 Vertical Pattern
7-16
7-16
7-16
Horizontal Pattern
4 x 7-16 female Bottom or top 25 kg Frontal: 470 N (at 150 km/h) Lateral: 280 N (at 150 km/h) Rearside: 1040 N (at 150 km/h) 200 km/h 2692 x 287 x 165 mm 2580 / 262 / 116 mm
115
60 4
Wind load
Max. wind velocity

10 10
Packing size
dB dB
3 0
3 0
Height/width/depth
Horizontal Pattern
Vertical Pattern
67
Dual-band A-Panel Dual Polarization Half-power Beam Width Fixed Electrical Downtilt Integrated Combiner
870 960 X 65 6
1710 1880 X 60 6 C
XXPol A-Panel 870960/17101880 C 65/ 60 17.5/17.5dBi 6T

Type No. XXPol Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt Front-to-back ratio, copolar Isolation, between ports Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input
741 336
900 870 960 870 960 MHz +45, 45 2 x 17.5 dBi Horizontal: Vertical: 6, fixed > 30 dB > 30 dB 50 < 1.5 < 150 dBc 65 7 1800 17101880 1710 1880 MHz +45, 45 2 x 17.5 dBi Horizontal: 60 Vertical: 6.5 6, fixed > 30 dB > 30 dB 50 < 1.5 < 150 dBc
Integrated combiner

65 7
120
10
10
1710 1880 45
dB
870 960 45 C
870 960 +45 C
1710 1880 +45
dB
3 0
3 0
Horizontal Pattern
7-16
7-16
Mechanical specifications Input 2 x 7-16 female Bottom 25 kg Frontal: 470 N (at 150 km/h) Lateral: 280 N (at 150 km/h) Rearside: 1040 N (at 150 km/h) 200 km/h 2692 x 287 x 165 mm 2580 / 262 / 116 mm
115
60
Connector position Weight

6.5
Wind load
10
10
dB
3 0
3 0
dB
Horizontal Pattern
68
Dual-band A-Panel Dual Polarization Half-power Beam Width Fixed Electrical Downtilt
870 960 X 65 6
1710 1880 X 60 6
XXPol A-Panel 870960/17101880 65/ 60 17.5/18dBi 6T

Type No. Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt Front-to-back ratio, copolar Isolation, between ports XXPol 1710 1880 45
dB
741 344
870 960 870 960 MHz +45, 45 2 x 17.5 dBi Horizontal: Vertical: 6, fixed > 30 dB 65 7 17101880 1710 1880 MHz +45, 45 2 x 18 dBi Horizontal: 60 Vertical: 6.5 6, fixed > 30 dB

65 7
120
10
10
870 960 45
870 960 +45
1710 1880 +45
dB
3 0
3 0
7-16
7-16
7-16
7-16
Horizontal Pattern
Vertical Pattern 6 electrical downtilt Mechanical specifications Input 4 x 7-16 female Bottom 25 kg Frontal: 470 N (at 150 km/h) Lateral: 280 N (at 150 km/h) Rearside: 1040 N (at 150 km/h) 200 km/h 2692 x 287 x 165 mm 2580 / 262 / 116 mm
115
60
Connector position Weight

6.5
Wind load
10
10
dB
3 0
3 0
dB
Horizontal Pattern
69
Dual-band A-Panel Dual Polarization Half-power Beam Width Adjust. Electr. Downtilt Integrated Combiner
870 960 X 65 2 8
1710 1880 X 60 2 C
XXPol A-Panel 870960/17101880 C 65/ 60 17/18dBi 28T/2T

Type No. XXPol Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Isolation, between ports Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input
742 047
900 870 960 870 960 MHz +45, 45 2 x 17 dBi (0.5 dB) Horizontal: Vertical: 65 7 1800 17101880 1710 1880 MHz +45, 45 2 x 18 dBi (0.5 dB) Horizontal: Vertical: 2, fixed 2 T 17 dB > 30 dB > 30 dB 50 < 1.5 < 150 dBc 60 6
2 8, adjustable 2 ... 4 ... 6 ... 8 T 20 ... 18 ... 17 ... 15 dB > 30 dB > 30 dB 50 < 1.5 < 150 dBc
Integrated combiner

65
7
120
10
1710 1880 45
10
dB
870 960 45 C
870 960 +45 C
1710 1880 +45
3 0
3 0
dB
Horizontal Pattern
7-16 Mechanical specifications Input Connector position Adjustment mechanism Weight

6
7-16
2 x 7-16 female Bottom 1x, Position bottom continuously adjustable 25 kg Frontal: 470 N (at 150 km/h) Lateral: 280 N (at 150 km/h) Rearside: 1040 N (at 150 km/h) 200 km/h 2692 x 287 x 165 mm 2580 / 262 / 116 mm
120
60
Wind load
10
10
dB
3 0
3 0
dB
Horizontal Pattern
70
Summary Directional Antennas Vertical Polarization GSM 1800 / GSM 1900 / PCS
Vertical Polarization
Type Type No. Height [mm] 1942 Connector position bottom or top Page
VPol F-Panel
17101990
33
22.5dBi
739 136
72
VPol F-Panel VPol F-Panel
17101900 17101900
65 65
10dBi 18dBi 2T
734 304 735 147
182 1302
bottom or top bottom
73
GSM 1800 VPol 71
73
VPol F-Panel VPol F-Panel VPol F-Panel
17101900 17101900 17101900
90 90 90
8dBi 16.5dBi 17.5dBi 2T 2T
734 318 734 328 734 330
182 1302 1942
bottom or top bottom bottom
74 74 75
Additional versions on request

17101990 V 33
739 136
1710 1990 MHz Vertical 22.5 dBi (1880 1990 MHz) 22 dBi (1710 1880 MHz) H-plane: 33 E-plane: 4.5 > 25 dB 50 < 1.5 < 150 dBc 200 W (at 50 C ambient temperature) 7-16 female Bottom or top 11 kg Frontal / Lateral / Rearside: 540 N / 210 N / 770 N 200 km/h 1942 / 262 / 59 mm
3 0
dB
33
10
3 0
Horizontal Pattern
dB
4.5
10
Vertical Pattern
72

17101900 V 65
734 304
10
120
65
H-plane: 65 E-plane: 55 > 25 dB 50 < 1.3 (1710 1880 MHz) < 1.5 (1880 1900 MHz) < 150 dBc 200 W (at 50 C ambient temperature) 7-16 female Bottom or top 1.3 kg Frontal / Lateral / Rearside: 30 N / 5 N / 40 N 200 km/h 182 / 155 / 36 mm
3 0
Horizontal Pattern VPol

55
10 3 0
Vertical Pattern
VPol F-Panel 17101900 65 18dBi 2T

Type No. Frequency range Polarization Gain Half-power beam width Electrical downtilt Side lobe suppression Front-to-back ratio Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth
735 147
10
dB
dB
120
65
H-plane: 65 E-plane: 7 2, fixed above horizon for first sidelobe better or equal 14 dB below maximum gain > 25 dB 50 < 1.3 (1710 1880 MHz) < 1.5 (1880 1900 MHz) < 150 dBc 200 W (at 50 C ambient temperature) 7-16 female Bottom 4.6 kg Frontal / Lateral / Rearside: 260 N / 55 N / 310 N 200 km/h 1302 / 155 / 36 mm
3 0
Horizontal Pattern
dB
7
10
3 0
Vertical Pattern 2 electrical downtilt first null-fill below horizon better or equal to 25 dB below maximum gain
dB
73

Type No. Frequency range Polarization Gain Half-power beam width Front-to-back ratio Impedance VPol VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth
17101900 V 90
734 318
1710 1900 MHz Vertical 8 dBi H-plane: 90 E-plane: 55 > 19 dB 50 < 1.3 (1710 1880 MHz) < 1.5 (1880 1900 MHz) < 150 dBc 200 W (at 50 C ambient temperature) 7-16 female Bottom or top 1.4 kg Frontal / Lateral / Rearside: 30 N / 15 N / 40 N (at 150 km/h) 200 km/h 182 / 155 / 49 mm
3 0
dB
90 180
3 0
Horizontal Pattern
dB
55
10
Vertical Pattern
VPol F-Panel 17101900 90 16.5dBi 2T

Type No. Frequency range Polarization Gain Half-power beam width Electrical downtilt Side lobe suppression Front-to-back ratio Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth
734 328
1710 1900 MHz Vertical 16.5 dBi H-plane: 90 E-plane: 7 2, fixed above horizon for first sidelobe better or equal 14 dB below maximum gain > 23 dB 50 < 1.3 (1710 1880 MHz) < 1.5 (1880 1900 MHz) < 150 dBc 200 W (at 50 C ambient temperature) 7-16 female Bottom 4.6 kg Frontal / Lateral / Rearside: 250 N / 110 N / 310 N 200 km/h 1302 / 155 / 49 mm
10 3 0
dB
90 180
Horizontal Pattern
3 0
74
dB
F-Panel Vertical Polarization Half-power Beam Width Fixed Electrical Downtilt

VPol F-Panel 17101900 90 17.5dBi 2T
Type No. Frequency range Polarization Gain Half-power beam width Electrical downtilt Sidelobe suppression Front-to-back ratio Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power Input Connector position Weight Wind load (at 150 km/h) Max. wind velocity Height/width/depth
17101900 V 90 2
734 330
1710 1900 MHz Vertical 17.5 dBi H-plane: 90 E-plane: 5 2, fixed above horizon for first sidelobe better or equal 14 dB below maximum gain > 23 dB 50 < 1.3 (1710 1880 MHz) < 1.5 (1880 1900 MHz) < 150 dBc 200 W (at 50 C ambient temperature) 7-16 female Bottom 6.9 kg Frontal / Lateral / Rearside: 380 N / 180 N / 480 N 200 km/h 1942 / 155 / 49 mm
10 3 0
dB
90 180
Horizontal Pattern VPol

5
3 0
dB
75
76
Summary Directional Antennas Dual Polarization + 45/ 45 UMTS

Dual Polarization + 45/ 45 1800/1900/2000
Type Type No. Height [mm] 1046 1302 Page
17102170 17102170
33 33
20dBi 21dBi
010T 800 10251 08T 742 351
78 79
17102170 17102170
45 45
19.5dBi 21.5dBi
08T 06T
742 218 742 219
1306 1942
80 81
XPol XPol XPol XPol XPol XPol XPol XPol XPol
F-Panel F-Panel F-Panel F-Panel F-Panel F-Panel F-Panel F-Panel F-Panel
17102170 17102170 17102170 17102170 17102170 17102170 17102170 17102170 17102170
65 65 65 65 65 65 65 65 65
9dBi 12dBi 15.5dBi 15.5dBi 16dBi 18dBi 18dBi 18.5dBi 19.5dBi
0T 742 210 2T 739 489 010T 742 211 012T 800 10247 0T 742 196 08T 742 212 010T 742 215 2T 741 794 06T 742 213
155 342 662 735 735 1302 1302 1302 1942
82 83 84 85 86 87 88 89 90
XPol XPol XPol XPol XPol
F-Panel F-Panel F-Panel F-Panel F-Panel
17102170 17102170 17102170 17102170 17102170
88 88 88 88 88
11.5dBi 17dBi 14dBi 17dBi 18dBi
0T 2T 010T 08T 06T
741 741 741 741 741
984 987 988 989 990
342 1302 662 1302 1942
91 92 93 94 95
New Products
77
UMTS XPol
Multi-band F-Panel Dual Polarization Half-power Beam Width Adjust. Electrical Downtilt
Type No. Frequency range 1710 1880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression: Vertical Pattern first sidelobe above horizon Horizontal Pattern Front-to-back ratio, copolar (180 30) Cross polar ratio Maindirection Sector Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 0 30 +45, 45 2 x 19.5 dBi Horizontal: Vertical: 0 10 36 9
1710 2170 X 33 0 10
800 10251
17102170 1850 1990 MHz +45, 45 2 x 19.8 dBi Horizontal: 35 Vertical: 8.5 0 10 1920 2170 MHz +45, 45 2 x 20.0 dBi Horizontal: Vertical: 0 10 33 8
0 ... 5 ... 10T 15 ... 15 15 dB > 14 dB > 30 dB
0 ... 5 ... 10T 15 ... 15 ... 15 dB > 14 dB > 30 dB
0 ... 5 ... 10T 15 ... 15 ... 15 dB > 14 dB > 30 dB
Typically: 20 dB > 10 dB > 30 dB 50 < 1.5
Typically: 20 dB > 10 dB > 30 dB 50 < 1.5 < 150 dBc
36
10
10
3 0
dB
3 0
Horizontal Pattern
dB
1710 2170 45
1710 2170 +45

7-16
35
7-16
8,5
10
dB
10
dB
3 0
3 0
Horizontal Pattern
33
Max. wind velocity

10
10
Packing size
dB
dB
3 0
3 0
Height/width/depth
Horizontal Pattern
78
Type No. Frequency range 1710 1880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression: Vertical Pattern first sidelobe above horizon Horizontal Pattern Front-to-back ratio, copolar Cross polar ratio Maindirection Sector Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 0 30 +45, 45 2 x 20.2 dBi Horizontal: 36 Vertical: 7.4 0 8
1710 2170 X 33 0 8
742 351
17102170 1850 1990 MHz +45, 45 2 x 20.5 dBi Horizontal: 35 Vertical: 7.0 0 8 1920 2170 MHz +45, 45 2 x 20.7 dBi Horizontal: 33 Vertical: 6.7 0 8
0 ... 4 ... 8 T 18 ... 17 16 dB > 14 dB > 30 dB Typically: 20 dB > 10 dB > 30 dB 50 < 1.5
0 ... 4 ... 8 T 18 ... 18 ... 17 dB > 14 dB > 30 dB Typically: 20 dB > 10 dB > 30 dB 50 < 1.5 < 150 dBc
0 ... 4 ... 8 T 18 ... 17 ... 16 dB > 14 dB XPol 1710 2170 +45 7-16 2 x 7-16 female Bottom 1x, Position bottom continuously adjustable 12 kg Frontal: Lateral: Rearside: 570 N (at 150 km/h) 110 N (at 150 km/h) 570 N (at 150 km/h) 200 km/h 1574 x 320 x 92 mm 1302 / 299 / 69 mm 79 > 30 dB Typically: 20 dB > 10 dB > 30 dB 50 < 1.5
36
7.4
10
10
3 0
dB
3 0
Horizontal Pattern
dB
1710 2170 45

7-16
35
10
dB
10
Mechanical specifications Input Connector position Adjustment mechanism Weight Wind load
dB
3 0
3 0
Horizontal Pattern
33
6.7
Max. wind velocity

10
10
Packing size
dB
dB
3 0
3 0
Height/width/depth
Horizontal Pattern
XPol F-Panel 17102170 45 19.5dBi 08T
Type No. Frequency range 1710 1880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression: Vertical Pattern first sidelobe above horizon Horizontal Pattern XPol Front-to-back ratio (180 30) Cross polar ratio Maindirection Sector Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 0 30 +45, 45 2 x 19 dBi Horizontal: 47 Vertical: 7.3 0 8
1710 2170 X 45 0 8
742 218
17102170 1850 1990 MHz +45, 45 2 x 19.5 dBi Horizontal: Vertical: 0 8 45 7 1920 2170 MHz +45, 45 2 x 19.6 dBi Horizontal: 44 Vertical: 6.7 0 8
0 ... 2 ... 5 ... 8 T 0 ... 2 ... 5 ... 8 T 0 ... 2 ... 5 ... 8 T 17 ... 17 ... 15 ... 15 dB 18 ... 18 ... 17 ... 17 dB 18 ... 18 ... 15 ... 15 dB > 18 dB > 18 dB > 18 dB Copolar: > 27 dB Total power: > 25 dB Typically: 18 dB > 13 dB > 30 dB 50 < 1.5 Copolar: > 30 dB Total power: > 25 dB Typically: 18 dB > 13 dB > 30 dB 50 < 1.5 < 150 dBc 300 W (at 50 C ambient temperature) Copolar: > 27 dB Total power: > 25 dB Typically: 18 dB > 13 dB > 30 dB 50 < 1.5

47 7.3
10
10
dB
3 0
3 0
Horizontal Pattern
dB
1710 2170 45
1710 2170 +45

45 7
10 10
7-16
7-16
Mechanical specifications Input Connector position Adjustment mechanism Weight Wind load Frontal: Lateral: Rearside: 2 x 7-16 female Bottom 1x, Position bottom continuously adjustable 10.2 kg 165 N (at 150 km/h) 110 N (at 150 km/h) 390 N (at 150 km/h) 200 km/h 1604 x 221 x 107 mm 1306 / 199 / 69 mm
dB
3 0
dB
3 0
Horizontal Pattern

44 6.7
Max. wind velocity

10 10
Packing size
dB
dB
3 0
3 0
Height/width/depth
Horizontal Pattern
80
XPol F-Panel 17102170 45 21.5dBi 06T
Type No. Frequency range 1710 1880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression: Vertical Pattern first sidelobe above horizon Horizontal Pattern Front-to-back ratio, copolar total power Cross polar ratio Maindirection Sector Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 0 60 +45, 45 2 x 20.5 dBi Horizontal: Vertical: 0 6 47 5
1710 2170 X 45 0 6
742 219
17102170 1850 1990 MHz +45, 45 2 x 21 dBi Horizontal: 45 Vertical: 4.7 0 6 1920 2170 MHz +45, 45 2 x 21.5 dBi Horizontal: 43 Vertical: 4.5 0 6
0 ... 2 ... 4 ... 6T 0 ... 2 ... 4 ... 6T 0 ... 2 ... 4 ... 6T 17 ... 17 ... 17 ... 17 dB 18 ... 18 ... 18 ... 18 dB 18 ... 18 ... 18 ... 18 dB > 20 dB > 20 dB > 20 dB XPol 1710 2170 +45 7-16
4.7
> 25 dB > 25 dB Typically: 18 dB > 10 dB > 30 dB 50 < 1.5
> 25 dB > 25 dB Typically: 18 dB > 10 dB > 30 dB 50 < 1.5 < 150 dBc
> 25 dB > 25 dB Typically: 18 dB > 10 dB > 30 dB 50 < 1.5
300 Watt (at 50 C ambient temperature)

47 5
10
10
dB
3 0
3 0
Horizontal Pattern

45
dB
7-16
10
10
dB
3 0
dB
3 0
Horizontal Pattern

43 4.5
10 10
Max. wind velocity Packing size
dB
dB
3 0
3 0
Height/width/depth
Horizontal Pattern
Multi-band F-Panel Dual Polarization Half-power Beam Width Fixed Electrical Downtilt
Type No. Frequency range 1710 1880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt Front-to-back ratio, copolar Cross polar ratio Maindirection Sector 0 60 +45, 45 2 x 8.5 dBi Horizontal: Vertical: 0, fixed > 25 dB Typically: 25 dB > 10 dB 70 65
1710 2170 X 65 0
742 210
17102170 1850 1990 MHz +45, 45 2 x 8.6 dBi Horizontal: Vertical: 0, fixed > 30 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.4 < 150 dBc 150 W (at 50 C ambient temperature) 68 65 1920 2170 MHz +45, 45 2 x 8.7 dBi Horizontal: Vertical: 0, fixed > 30 dB Typically: 25 dB > 10 dB 65 63
XPol

135 70
65
10
10
dB
3 0
3 0
Horizontal Pattern
Vertical Pattern
dB

130 68
65
1710 2170 45
1710 2170 +45
7-16
10 3 0
7-16
10
dB
3 0
dB
Mechanical specifications Input Connector position* Weight 2 x 7-16 female Bottom or top 1.5 kg Frontal: Lateral: Rearside: 20 N (at 150 km/h) 15 N (at 150 km/h) 40 N (at 150 km/h) 200 km/h 257 x 172 x 92 mm 155 / 155 / 69 mm
Horizontal Pattern
Vertical Pattern

127 65
63
Wind load
10 3 0
10
dB
Height/width/depth
dB
3 0
Horizontal Pattern
Vertical Pattern
82
Type No. Frequency range 1710 1880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt Front-to-back ratio, copolar Cross polar ratio Maindirection Sector 0 60 +45, 45 2 x 11.5 dBi Horizontal: Vertical: 3, fixed > 30 dB Typically: 25 dB > 10 dB 67 32
1710 2170 X 65 2
739 489
17102170 1850 1990 MHz +45, 45 2 x 12 dBi Horizontal: Vertical: 2, fixed > 30 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.4 < 150 dBc 150 W (at 50 C ambient temperature) 65 30 1920 2170 MHz +45, 45 2 x 12 dBi Horizontal: Vertical: 0, fixed > 27 dB Typically: 25 dB > 10 dB 63 28

125 67
32
10 3 0 0 10
dB
Horizontal Pattern

120 65 30
dB
1710 2170 45
1710 2170 +45
10
10
7-16
dB
7-16
3 0
dB
3 0
Mechanical specifications Input Connector position 2 x 7-16 female Bottom 2 kg Frontal: Lateral: Rearside: 35 N (at 150 km/h) 25 N (at 150 km/h) 80 N (at 150 km/h) 200 km/h 444 x 172 x 92 mm 342 / 155 / 69 mm
Horizontal Pattern

115 63 28
Weight Wind load
Max. wind velocity

10 10
Packing size
dB
dB
3 0
3 0
Height/width/depth
Horizontal Pattern
XPol
XPol F-Panel 17102170 65 15.5dBi 010T
Type No. Frequency range 1710 1880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression for first sidelobe above horizon Front-to-back ratio XPol Cross polar ratio Maindirection Sector Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input +45, 45 2 x 14.7 dBi Horizontal: 69 Vertical: 14.5 0 10
1710 2170 X 65 010
742 211
17102170 1850 1990 MHz +45, 45 2 x 15 dBi Horizontal: Vertical: 0 10 67 14 1920 2170 MHz +45, 45 2 x 15.2 dBi Horizontal: Vertical: 0 10 0 ... 4 ... 8 ... 10T 18 ... 18 ... 18 ... 16 dB Copolar: > 30 dB Total power: > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.4 64 13
0 ... 4 ... 8 ... 10T 0 ... 4 ... 8 ... 10T 18 ... 16 ... 15 .... 15 dB 18 ... 18 ... 18 ... 18 dB Copolar: > 30 dB Total power: > 25 dB Copolar: > 30 dB Total power: > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.4 < 150 dBc
0 60

130 69
14.5
10 3 0
10
dB
3 0
Horizontal Pattern
Vertical Pattern 0 10 electrical downtilt 1710 2170 45 1710 2170 +45

128 67
14
dB

dB
7-16
10 3 0
10
3 0
Input Connector position Adjustment mechanism Weight Wind load
2 x 7-16 female Bottom 1x, Position bottom continuously adjustable 4.5 kg Frontal: Lateral: Rearside: 65 N (at 150 km/h) 50 N (at 150 km/h) 160 N (at 150 km/h) 200 km/h 924 x 172 x 92 mm 662 / 155 / 69 mm
Horizontal Pattern
dB

120 64
13
Max. wind velocity

10 3 0
0 10
Packing size
dB
dB
Height/width/depth
Horizontal Pattern
84
XPol F-Panel 17102170 65 15.5dBi 012T
Type No. Frequency range 1710 1880 MHz Polarization Gain per input Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression for first sidelobe above horizon Front-to-back ratio Cross polar ratio Maindirection Sector Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 0 60 +45, 45 0 ... 4 ... 8 ... 12 T 15.5 ... 15.4 ... 15.9 ...15.1 dBi Horizontal: 67 Vertical: 12.9 0 12 0 ... 4 ... 8 ... 12 T 14 ... 14 ... 14 .... 14 dB Copolar: > 27 dB
1710 2170 X 65 012
800 10247
17102170 1850 1990 MHz +45, 45 0 ... 4 ... 8 ... 12 T 15.6 ... 15.5 ... 15.4 ...15 dBi Horizontal: 66 Vertical: 12.3 0 12 0 ... 4 ... 8 ... 12 T 14 ... 14 ... 14 ... 14 dB Copolar: > 27 dB 1920 2170 MHz +45, 45 0 ... 4 ... 8 ... 12 T 15.8 ... 15.7 ... 15.5 ...14.9 dBi Horizontal: 64 Vertical: 11.5 0 12 0 ... 4 ... 8 ... 12 T 14 ... 14 ... 14 ... 14 dB XPol Bottom 1x, Position bottom continuously adjustable 4.5 kg Frontal: Lateral: Rearside: 75 N (at 150 km/h) 55 N (at 150 km/h) 180 N (at 150 km/h) 200 km/h 1000 x 172 x 95 mm 735 / 155 / 69 mm 85 Copolar: > 27 dB
Typically: 20 dB > 10 dB > 30 dB 50 < 1.5 < 150 dBc 300 W (at 50 C ambient temperature)

122 67
12.9
10 3 0
10
dB
3 0
Horizontal Pattern

122 66
dB
7-16
12.3
7-16
10 3 0
10
dB
3 0
2 x 7-16 female
Horizontal Pattern
dB

120 64
11.5
Max. wind velocity

10 3 0
0 10
Packing size
dB
dB
Height/width/depth
Horizontal Pattern
Type No. Frequency range 1710 1880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Sidelobe suppression for first sidelobe above horizon Front-to-back ratio (180 30) Cross polar ratio Maindirection Sector 0 60 +45, 45 2 x 15.3 dBi Horizontal: 67 Vertical: 12.6 > 14 dB Copolar: > 30 dB Total power: > 25 dB Typically: 25 dB > 10 dB
1710 2170 X 65 0
742 196
17102170 1850 1990 MHz +45, 45 2 x 15.6 dBi Horizontal: 66 Vertical: 11.8 > 16 dB Copolar: > 30 dB Total power: > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.4 < 150 dBc 300 W (at 50 C ambient temperature) 1920 2170 MHz +45, 45 2 x 15.8 dBi Horizontal: Vertical: > 14 dB Copolar: > 30 dB Total power: > 25 dB Typically: 25 dB > 10 dB 64 11
XPol

125 67 12.6
10 3 0
10
dB
3 0
Horizontal Pattern
Vertical Pattern

1710 2170 45
125 66
11.8
dB
1710 2170 +45
7-16
10 3 0
0 10
dB
7-16
dB

11.1
Horizontal Pattern
Vertical Pattern
2 x 7-16 female Bottom 3.7 kg Frontal: Lateral: Rearside: 75 N (at 150 km/h) 55 N (at 150 km/h) 180 N (at 150 km/h) 200 km/h 1000 x 172 x 95 mm 735 / 155 / 69 mm

120 64
10 3 0
10
Max. wind velocity

dB
dB
3 0
Horizontal Pattern
Vertical Pattern
86
Type No. Frequency range 1710 1880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression for first sidelobe above horizon Front-to-back ratio (180 30) Cross polar ratio Maindirection Sector Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 0 60 +45, 45 2 x 17.5 dBi Horizontal: Vertical: 0 8 67 7
1710 2170 X 65 0 8
742 212
17102170 1850 1990 MHz +45, 45 2 x 17.7 dBi Horizontal: 65 Vertical: 6.7 0 8 1920 2170 MHz +45, 45 2 x 18 dBi Horizontal: 63 Vertical: 6.5 0 8 0 ... 2 ... 5 ... 8 T 20 ... 20 ... 18 ... 16 dB Copolar: > 30 dB Total power: > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5
0 ... 2 ... 5 ... 8 T 0 ... 2 ... 5 ... 8 T 17 ... 17 ... 15 .... 15 dB 20 ... 20 ... 18 ... 18 dB Copolar: > 30 dB Total power: > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5 Copolar: > 30 dB Total power: > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5 < 150 dBc

125 67
7
10 3 0 0 10
dB
Horizontal Pattern

120 65
dB
7-16
6.7
7-16
10
10
dB
dB
3 0
3 0
Horizontal Pattern

120 63 6.5
Max. wind velocity

10 10
Packing size
dB
dB
3 0
3 0
Height/width/depth
Horizontal Pattern
XPol
Type No. Frequency range 1710 1880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression for first sidelobe above horizon Front-to-back ratio (180 30) Cross polar ratio Maindirection Sector Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 0 60 +45, 45 2 x 17.5 dBi Horizontal: Vertical: 0 10 0 ... 5 ... 10T 16 ... 15 ... 14 dB Copolar: > 30 dB Total power: > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5 67 7
1710 2170 X 65 0 10
742 215
17102170 1850 1990 MHz +45, 45 2 x 17.7 dBi Horizontal: 65 Vertical: 6.7 0 10 0 ... 5 ... 10T 17 ... 16 ... 15 dB Copolar: > 30 dB Total power: > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5 < 150 dBc 300 W (at 50 C ambient temperature) 1920 2170 MHz +45, 45 2 x 18 dBi Horizontal: 63 Vertical: 6.5 0 10 0 ... 5 ... 10T 17 ... 16 ... 15 dB Copolar: > 30 dB Total power: > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5
XPol

125 67
7
10 3 0 0 10
Horizontal Pattern

120 65
dB
dB
7-16
6.7
7-16
10
10
dB
dB
3 0
3 0
Horizontal Pattern

120 63 6.5
Max. wind velocity

10 10
Packing size
dB
dB
3 0
3 0
Height/width/depth
Horizontal Pattern
88
Type No. Frequency range 1710 1880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Cross polar ratio Maindirection Sector 0 60 +45, 45 2 x 17.5 dBi Horizontal: Vertical: 2, fixed > 14 dB > 30 dB Typically: 30 dB > 10 dB 67 7
1710 2170 X 65 2
741 794
17102170 1850 1990 MHz +45, 45 2 x 18 dBi Horizontal: 65 Vertical: 6.7 2, fixed > 14 dB > 30 dB Typically: 30 dB > 10 dB > 30 dB 50 < 1.4 < 150 dBc 300 W (at 50 C ambient temperature) 1920 2170 MHz +45, 45 2 x 18.5 dBi Horizontal: 63 Vertical: 6.5 2, fixed > 14 dB > 30 dB Typically: 30 dB > 10 dB

125 67 7
10 3 0
10
dB
3 0
Horizontal Pattern

1710 2170 45
120 65 6.7
dB
1710 2170 +45
7-16
10 10
dB
7-16
3 0
3 0
dB
Mechanical specifications Input Connector position 2 x 7-16 female Bottom 6.6 kg Frontal: Lateral: Rearside: 130 N (at 150 km/h) 110 N (at 150 km/h) 310 N (at 150 km/h) 200 km/h 1404 x 172 x 92 mm 1302 / 155 / 69 mm
Horizontal Pattern

115 63 6.5
Weight Wind load
Max. wind velocity

10 10
Packing size
dB
dB
3 0
3 0
Height/width/depth
Horizontal Pattern
XPol
XPol F-Panel 17102170 65 19.5dBi 06T
Type No. Frequency range 1710 1880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression for first sidelobe above horizon Front-to-back ratio (180 30) Cross polar ratio Maindirection Sector Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 0 60 +45, 45 2 x 19 dBi Horizontal: 67 Vertical: 4.7 0 6
1710 2170 X 65 0 6
742 213
17102170 1850 1990 MHz +45, 45 2 x 19.2 dBi Horizontal: 65 Vertical: 4.5 0 6 1920 2170 MHz +45, 45 2 x 19.5 dBi Horizontal: 63 Vertical: 4.3 0 6 0 ... 2 ... 4 ... 6 T 18 ... 18 ... 17 ... 15 dB Copolar: > 30 dB Total power: > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5
XPol

125 67
4.7
10 3 0 0 10
Horizontal Pattern

120 65
dB
dB
7-16
4.5
10
7-16
10
dB
dB
3 0
3 0
Horizontal Pattern

115 63 4.3
Max. wind velocity

10 10
Packing size
dB
dB
3 0
3 0
Height/width/depth
Horizontal Pattern
90
Multi-band F-Panel Dual Polarization Half-power Beam Width Excellent Sidelobe Suppression
XPol F-Panel 17102170 88 11.5dBi
Type No. Frequency range 1710 1880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Sidelobe suppression vertical sector 45 Front-to-back ratio (180 30) Cross polar ratio Maindirection Sector 0 60 +45, 45 2 x 11.3 dBi Horizontal: Vertical: > 20 dB Copolar: > 23 dB Total power: > 23 dB Typically: 20 dB > 18 dB 86 28
1710 2170 X 88 20 dB
741 984
17102170 1850 1990 MHz +45, 45 2 x 11.5 dBi Horizontal: Vertical: > 20 dB Copolar: > 23 dB Total power: > 23 dB Typically: 25 dB > 18 dB > 30 dB 50 < 1.4 < 150 dBc 150 W (at 50 C ambient temperature) 87 26 1920 2170 MHz +45, 45 2 x 11.6 dBi Horizontal: Vertical: > 20 dB Copolar: > 23 dB Total power: > 23 dB Typically: 20 dB > 15 dB 88 26

86 155
28
10
10 3 0 dB
3 0
dB
Horizontal Pattern

87 160
26
7-16
7-16
10
10 3 0 dB
3 0
dB
Mechanical specifications Input Connector position* Weight Wind load Frontal: Lateral: Rearside: 2 x 7-16 female Bottom or top 2 kg 35 N (at 150 km/h) 25 N (at 150 km/h) 80 N (at 150 km/h) 200 km/h 444 x 172 x 92 mm 342 / 155/ 69 mm
Horizontal Pattern
Vertical Pattern

88 160
Max. wind velocity

26
10
10 3 0 dB
3 0
dB
Horizontal Pattern
Vertical Pattern 91
XPol
Type No. Frequency range 1710 1880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt Sidelobe suppression for first sidelobe above horizon Front-to-back ratio (180 30) XPol Cross polar ratio Maindirection Sector 0 60 +45, 45 2 x 16.5 dBi Horizontal: 88 Vertical: 6.9 2, fixed > 16 dB Copolar: > 25 dB Total power: > 25 dB Typically: 20 dB > 10 dB
1710 2170 X 88 2
741 987
17102170 1850 1990 MHz +45, 45 2 x 16.8 dBi Horizontal: 88 Vertical: 6.5 2, fixed > 16 dB Copolar: > 25 dB Total power: > 25 dB Typically: 20 dB > 10 dB > 30 dB 50 < 1.4 < 150 dBc 300 W (at 50 C ambient temperature) 1920 2170 MHz +45, 45 2 x 17 dBi Horizontal: 88 Vertical: 6.2 2, fixed > 16 dB Copolar: > 25 dB Total power: > 25 dB Typically: 20 dB > 10 dB

88 160
6.9
10
10 3 0 dB
3 0
dB
Horizontal Pattern

88 162
6.5
7-16
7-16
10
10 3 0 dB
3 0
dB

6.2
Horizontal Pattern

88 163
Max. wind velocity

10
10 3 0 dB
dB
3 0
Horizontal Pattern
Vertical Pattern 2 electrical downtilt Mounting accessories are not included in the scope of delivery (see page 194 197)
92
Type No. Frequency range 1710 1880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar total power Cross polar ratio Maindirection Sector Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 0 60 +45, 45 2 x 13.7 dBi Horizontal: 88 Vertical: 14.7 0 10
1710 2170 X 88 0 10
741 988
17102170 1850 1990 MHz +45, 45 2 x 14 dBi Horizontal: Vertical: 0 10 88 14 1920 2170 MHz +45, 45 2 x 14.1 dBi Horizontal: Vertical: 0 10 88 13
0 ... 4 ... 8 ... 10 T 0 ... 4 ... 8 ... 10 T 0 ... 4 ... 8 ... 10 T 18 ... 18 ... 18 ... 18 dB 18 ... 18 ... 18 ... 18 dB 18 ... 18 ... 18 ... 18 dB > 25 dB > 25 dB Typically: 20 dB > 10 dB > 30 dB 50 < 1.5 > 25 dB > 25 dB Typically: 20 dB > 10 dB > 30 dB 50 < 1.5 < 150 dBc 300 W (at 50 C ambient temperature) > 25 dB > 25 dB Typically: 20 dB > 10 dB > 30 dB 50 < 1.5

88 160
14.7
10
10 3 0 dB
3 0
dB
Horizontal Pattern

88 163
14

dB
7-16
10
10 3 0
3 0

13
Horizontal Pattern
dB

88 165
Max. wind velocity

10
10 3 0 dB
dB
3 0
Horizontal Pattern
XPol
Type No. Frequency range 1710 1880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression for first sidelobe above horizon Front-to-back ratio (180 30) Cross polar ratio Maindirection Sector Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 0 60 +45, 45 2 x 16.5 dBi Horizontal: Vertical: 0 8 88 7
1710 2170 X 88 0 8
741 989
17102170 1850 1990 MHz +45, 45 2 x 16.8 dBi Horizontal: 88 Vertical: 6.7 0 8 1920 2170 MHz +45, 45 2 x 16.7 dBi Horizontal: 88 Vertical: 6.5 0 8 0 ... 2 ... 5 ... 8 T 18 ... 18 ... 18 ... 17 dB Copolar: > 24 dB Total power: > 24 dB Typically: 20 dB > 10 dB > 30 dB 50 < 1.5
XPol

88 165
7
10
10 3 0 dB
3 0
dB
Horizontal Pattern

88 165
7-16
6.7
7-16
10
6.5
10 3 0
3 0
Horizontal Pattern
dB

88 165
dB
Max. wind velocity

10
10 3 0 dB
dB
3 0
Horizontal Pattern
94
Type No. Frequency range 1710 1880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar total power Cross polar ratio Maindirection Sector Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 0 60 +45, 45 2 x 17.7 dBi Horizontal: 88 Vertical: 4.9 0 6
1710 2170 X 88 0 6
741 990
17102170 1850 1990 MHz +45, 45 2 x 18 dBi Horizontal: 88 Vertical: 4.7 0 6 1920 2170 MHz +45, 45 2 x 18.2 dBi Horizontal: 88 Vertical: 4.5 0 6
0 ... 2 ... 4 ... 6 T 0 ... 2 ... 4 ... 6 T 0 ... 2 ... 4 ... 6 T 17 ... 17 ... 17 ...17 dB 18 ... 18 ... 18 ...18 dB 18 ... 18 ... 18 ...18 dB > 25 dB > 25 dB Typically: 20 dB > 10 dB > 30 dB 50 < 1.5 > 25 dB > 25 dB Typically: 20 dB > 10 dB > 30 dB 50 < 1.5 < 150 dBc 300 W (at 50 C ambient temperature) > 25 dB > 25 dB Typically: 20 dB > 10 dB > 30 dB 50 < 1.5

88 165
4.9
10
10 3 0 dB
3 0
dB
Horizontal Pattern

88 165
7-16
4.7
10
7-16
dB
10 3 0 dB
3 0
Horizontal Pattern

88 165
4.5
Max. wind velocity

10
10 3 0 dB
dB
3 0
Horizontal Pattern
XPol
96
Summary Directional Antennas 2-Multi-band UMTS

Dual Polarization + 45/ 45 1800/1900/2000
Type Type No. Height [mm] 679 Page
XXPol F-Panel
17102170 17102170
65 65
15dBi 15dBi
010T 010T
742 233
98
XXPol F-Panel
17102170 17102170
65 65
18dBi 18dBi
08T 08T
742 234
1304
99
XXPol F-Panel
17102170 17102170
65 65
19.5dBi 19.5dBi
06T 06T
742 235
1959
100
97
UMTS XXPol 2-Multi
2-Multi-band F-Panel Dual Polarization Half-power Beam Width Adjust. Electr. Downtilt
1710 2170 1710 2170 X 65 0 10 X 65 0 10

XXPol F-Panel 17102170/17102170 65/65 15/15dBi 010/010T
Type No. Frequency range 1710 1880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression for first sidelobe above horizon Front-to-back ratio Cross polar ratio Maindirection Sector Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 4 x 15 dBi Horizontal: Vertical: 0 10 67 14
742 233
17102170 1850 1990 MHz 4 x 15.2 dBi Horizontal: 65 Vertical: 13.7 0 10 1920 2170 MHz 4 x 15.3 dBi Horizontal: Vertical: 0 10 0 ... 4 ... 8 ... 10T 16 ... 16 ... 16 ... 16 dB Copolar: > 25 dB Total power: > 25 dB Typically: 20 dB Typically: 10 dB > 30 dB 50 < 1.5 62 13 +45, 45; +45, 45 +45, 45; +45, 45 +45, 45; +45, 45
0 ... 4 ... 8 ... 10T 0 ... 4 ... 8 ... 10T 16 ... 16 ... 15 .... 15 dB 16 ... 16 ... 16 ... 16 dB Copolar: > 25 dB Total power: > 25 dB Copolar: > 25 dB Total power: > 25 dB Typically: 20 dB Typically: 10 dB > 30 dB 50 < 1.5 < 150 dBc
0 60
Typically: 20 dB Typically: 10 dB > 30 dB 50 < 1.5
Isolation, between inputs

130 67
14
10 3 0
10
dB
3 0
Horizontal Pattern
Vertical Pattern 0 10 electrical downtilt 1710 2170 +45 1710 2170 45 1710 2170 +45 1710 2170 45

125 65
dB
7-16
13.7
7-16
7-16
7-16
10 3 0
10
dB
3 0
4 x 7-16 female Bottom 2 x, Position bottom continuously adjustable 10.4 kg Frontal: Lateral: Rearside: 290 N (at 150 km/h) 55 N (at 150 km/h) 290 N (at 150 km/h) 200 km/h 924 x 360 x 130 mm 679 / 322 / 71 mm
Horizontal Pattern
dB

120 62
13
Max. wind velocity

10 3 0
0 10
Packing size
dB
dB
Height/width/depth
Horizontal Pattern
98
1710 2170 1710 2170 X 65 0 8 X 65 0 8

XXPol F-Panel 17102170/17102170 65/65 18/18dBi 08/08T
Type No. Frequency range 1710 1880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression for first sidelobe above horizon Front-to-back ratio Cross polar ratio Maindirection Sector Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 4 x 17.5 dBi Horizontal: Vertical: 0 8 66 7
742 234
17102170 1850 1990 MHz 4 x 17.7 dBi Horizontal: 65 Vertical: 6.7 0 8 1920 2170 MHz 4 x 17.8 dBi Horizontal: 64 Vertical: 6.5 0 8 0 ... 2 ... 5 ... 8 T 20 ... 20 ... 18 ... 16 dB Copolar: > 25 dB Total power: > 25 dB Typically: 25 dB > 10 dB 50 < 1.5 XXPol 2-Multi 1710 2170 +45 1710 2170 45 7-16 7-16 7-16 4 x 7-16 female Bottom 2 x, Position bottom continuously adjustable 12 kg Frontal: Lateral: Rearside: 570 N (at 150 km/h) 110 N (at 150 km/h) 570 N (at 150 km/h) 200 km/h 1574 x 320 x 92 mm 1304 / 299 / 69 mm 99 > 30 dB +45, 45; +45, 45 +45, 45; +45, 45 +45, 45; +45, 45
0 ... 2 ... 5 ... 8 T 0 ... 2 ... 5 ... 8 T 17 ... 17 ... 15 .... 15 dB 20 ... 20 ... 18 ... 18 dB Copolar: > 25 dB Total power: > 25 dB Copolar: > 25 dB Total power: > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5 < 150 dBc
0 60

130 66
7
10 3 0 0 10
dB
Horizontal Pattern
Vertical Pattern 0 8 electrical downtilt 1710 2170 +45 1710 2170 45

125 65
dB
7-16
6.7
10 3 0
10
dB
dB
3 0
Horizontal Pattern

120 64 6.5
Max. wind velocity

10 3 0 0 10
Packing size
dB
dB
Height/width/depth
Horizontal Pattern
1710 2170 1710 2170 X 65 0 6 X 65 0 6

XXPol F-Panel 17102170/17102170 65/65 19.5/19.5dBi 06/06T
Type No. Frequency range 1710 1880 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression for first sidelobe above horizon XXPol 2-Multi Front-to-back ratio Cross polar ratio Maindirection Sector Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 4 x 19 dBi Horizontal: 65 Vertical: 4.6 0 6
742 235
17102170 1850 1990 MHz 4 x 19.2 dBi Horizontal: 64 Vertical: 4.4 0 6 1920 2170 MHz 4 x 19.5 dBi Horizontal: 63 Vertical: 4.2 0 6 0 ... 2 ... 4 ... 6T 17 ... 17 ... 15 ... 15 dB Copolar: > 30 dB Total power: > 24 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5 +45, 45; +45, 45 +45, 45; +45, 45 +45, 45; +45, 45
0 ... 2 ... 4 ... 6T 0 ... 2 ... 4 ... 6T 17 ... 17 ... 14 .... 14 dB 17 ... 17 ... 15 ... 15 dB Copolar: > 30 dB Total power: > 25 dB Copolar: > 30 dB Total power: > 25 dB Typically: 25 dB > 10 dB > 30 dB 50 < 1.5 < 150 dBc
0 60

130 65
4.6
10
10
3 0
3 0
Horizontal Pattern
Vertical Pattern 0 6 electrical downtilt 1710 2170 +45 1710 2170 45 1710 2170 +45 1710 2170 45

127 64
dB
dB
7-16
4.4
7-16
7-16
7-16
10 3 0
10
Mechanical specifications Input Connector position Adjustment mechanism Weight Wind load Frontal: Lateral: Rearside: 4 x 7-16 female Bottom 2 x, Position bottom continuously adjustable 18 kg 870 N (at 150 km/h) 230 N (at 150 km/h) 870 N (at 150 km/h) 200 km/h 2384 x 360 x 130 mm 1959 / 323 / 71 mm
dB
dB
3 0
Horizontal Pattern

124 63
4.2
10 3 0 0 10
dB
dB
Height/width/depth
Horizontal Pattern
100
Summary Directional Antennas Dual-band UMTS

Dual Polarization + 45/ 45 800/900 1800/1900/2000
XXPol A-Panel
806 960 17102170 806 960 17102170 C
65 60 65 60
12dBi 14dBi 12dBi 14dBi
0T 0T 0T 0T
742 226
102
XXPol A-Panel
742 222
579
103
XXPol A-Panel
824 960 17102170 824 960 17102170 824 960 17102170
65 65 65 65 65 65
14dBi 17dBi 16dBi 18.5dBi 17dBi 18.5dBi
014T 08T 010T 06T 07T 06T
742 264
1316
104
XXPol A-Panel
742 265
1916
105
XXPol A-Panel
742 266
2516
106
New Product
101
UMTS XXPol Dual-b.
Dual-band A-Panel Dual Polarization Half-power Beam Width Fixed Electr. Downtilt
806 960 X 65 0
1710 2170 X 60 0
XXPol A-Panel 806960/17102170 65/ 60 12/14dBi 0/0T

Type No. Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Front-to-back ratio (180 30) Cross polar ratio Maindirection Sector Isolation: Intrasystem Isolation: Intersystem Impedance VSWR XXPol Dual-b. Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 50 < 1.5 50 < 1.5 < 150 dBc 250 W (at 50 C ambient temperature) [dB] [dB] 0 60
742 226
806 960 17102170 806 866 MHz 824 894 MHz 880 960 MHz 1710 1880 MHz1850 1990 MHz1920 2170 MHz +45, 45 2 x 11.1 dBi +45, 45 2 x 11.4 dBi +45, 45 2 x 11.8 dBi +45, 45 2 x 12.8 dBi +45, 45 2 x 13.3 dBi +45, 45 2 x 13.6 dBi
Horizontal: 67 Horizontal: 66 Horizontal: 64 Horizontal: 66 Horizontal: 60 Horizontal: 60 Vertical: 34 Vertical: 33 Vertical: 30 Vertical: 20 Vertical: 18 Vertical: 17.5 Copolar: > 23 Copolar: > 23 Copolar: > 25 Copolar: > 25 Copolar: > 25 Copolar: > 25 Total power:> 20 Total power:> 20 Total power:> 22 Total power:> 22 Total power:> 22 Total power:> 22 Typically: 25 dB Typically: 25 dB Typically: 25 dB Typically: 16 dB Typically: 18 dB Typically: 20 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB > 30 dB > 30 dB > 30 dB 50 < 1.5 > 30 dB 50 < 1.5 > 30 dB 50 < 1.5 < 150 dBc 200 W (at 50 C ambient temperature) > 30 dB 50 < 1.5
> 50 dB (806 960 // 1710 2170 MHz)

125 65
33
10 3 0
10
dB
3 0
Horizontal Pattern
Vertical Pattern

120 60 18
10
10
dB
dB
dB
3 0
3 0
1710 2170 45
806 960 45
806 960 +45
1710 2170 +45
Horizontal Pattern
Vertical Pattern 7-16 7-16 7-16 7-16
102
Dual-band A-Panel Dual Polarization Half-power Beam Width Fixed Electr. Downtilt Integrated Combiner
806 960 X 65 0
1710 2170 X 60 0 C
XXPol A-Panel 806960/17102170 C 65/ 60 12/14dBi 0/0T

Type No. Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Front-to-back ratio (180 30) Cross polar ratio Maindirection Sector Isolation: Intrasystem Isolation: Intersystem Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Integrated combiner 50 < 1.5 50 < 1.5 < 150 dBc 250 W (at 50 C ambient temperature) [dB] [dB] 0 60
742 222
806 960 17102170 806 866 MHz 824 894 MHz 880 960 MHz 1710 1880 MHz1850 1990 MHz1920 2170 MHz +45, 45 2 x 11.5 dBi +45, 45 2 x 11.8 dBi +45, 45 2 x 12 dBi +45, 45 2 x 13.5 dBi +45, 45 2 x 13.7 dBi +45, 45 2 x 14 dBi
Horizontal: 68 Horizontal: 66 Horizontal: 64 Horizontal: 64 Horizontal: 60 Horizontal: 58 Vertical: 34 Vertical: 33 Vertical: 32 Vertical: 18.5 Vertical: 17.5 Vertical: 17.3 Copolar: > 23 Copolar: > 23 Copolar: > 25 Copolar: > 25 Copolar: > 25 Copolar: > 25 Total power:> 20 Total power:> 20 Total power:> 22 Total power:> 22 Total power:> 22 Total power:> 22 Typically: 20 dB Typically: 20 dB Typically: 20 dB Typically: 16 dB Typically: 18 dB Typically: 20 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB > 30 dB > 30 dB > 30 dB 50 < 1.5 > 30 dB 50 < 1.5 > 30 dB 50 < 1.5 < 150 dBc 200 W (at 50 C ambient temperature) XXPol Dual-b. 103 > 30 dB 50 < 1.5
> 50 dB (806 960 // 1710 2170 MHz)
The insertion loss is included in the given antenna gain values.

125 65
33
10 3 0
10
dB
3 0
Horizontal Pattern
Vertical Pattern

120 60
17.5
10
10
dB
dB
3 0
3 0
dB
1710 2170 45 C 7-16
806 960 45
806 960 +45 C
1710 2170 +45
Horizontal Pattern
Vertical Pattern 7-16
Dual-band A-Panel Dual Polarization Half-power Beam Width Adjust. Electr. Downtilt
824 960 X 65 0 14
1710 2170 X 65 0 8

XXPol A-Panel 824960/17102170 65/ 65 14/17dBi 014/08T
Type No. Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Cross polar ratio Maindirection Sector Isolation: Intrasystem Isolation: Intersystem Impedance VSWR XXPol Dual-b. Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 50 < 1.5 < 150 dBc 250 W 0 60 824960 824 894 MHz 870 960 MHz +45, 45 2 x 14 dBi Horizontal: 68 Vertical: 16 0 14 +45, 45 2 x 14 dBi Horizontal: 65 Vertical: 14.5 0 14
742 264
17102170 1710 1880 MHz 1850 1990 MHz 1920 2170 MHz +45, 45 2 x 16.5 dBi Horizontal: 65 Vertical: 7.8 0 8 +45, 45 2 x 16.8 dBi Horizontal: 65 Vertical: 7.3 0 8 +45, 45 2 x 17 dBi Horizontal: 63 Vertical: 6.8 0 8
0 ... 7 ... 14 T 0 ... 7 ... 14 T 0 ... 4 ... 8 T 0 ... 4 ... 8 T 0 ... 4 ... 8 T 14 ... 14 ... 13 dB 14 ... 14 ... 13 dB 14 ... 14 ... 14 dB 16 ... 16 ... 15 dB 15 ... 16 ... 15 dB > 26 dB Typically: 20 dB > 10 dB > 30 dB > 26 dB Typically: 20 dB > 10 dB > 30 dB 50 < 1.5 > 25 dB Typically: 16 dB > 10 dB > 30 dB 50 < 1.5 > 25 dB Typically: 18 dB > 10 dB > 30 dB 50 < 1.5 < 150 dBc 200 W (at 50 C ambient temperature) > 25 dB Typically: 20 dB > 10 dB > 30 dB 50 < 1.5
> 50 dB (824 960 // 1710 2170 MHz)

65
14.5
125
1710 2170 45
824 960 45
824 960 +45
1710 2170 +45
10 3 0
10
dB
dB
3 0
7-16
7-16
7-16
7-16
Horizontal Pattern
Mechanical specifications Input 4 x 7-16 female Bottom 2 x, Position bottom continuously adjustable 16.5 kg Frontal: Lateral: Rearside: 230 N (at 150 km/h) 180 N (at 150 km/h) 430 N (at 150 km/h) 200 km/h 1615 x 302 x 192 mm 1316 / 262 / 139 mm

65 7
Connector position Adjustment mechanism
120
Weight Wind load
10
10
Max. wind velocity

dB
dB
3 0
3 0
Horizontal Pattern
104
824 960 X 65 010
1710 2170 X 65 0 6

XXPol A-Panel 824960/17102170 65/ 65 16/18.5dBi 010/06T
Type No. Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Cross polar ratio Maindirection Sector Isolation: Intrasystem Isolation: Intersystem Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 50 < 1.5 < 150 dBc 250 W 0 60 824960 824 894 MHz 880 960 MHz +45, 45 2 x 15.5 dBi Horizontal: 68 Vertical: 10.5 0.59.5 +45, 45 2 x 16 dBi Horizontal: 65 Vertical: 10 0.59.5
742 265
17102170 1710 1880 MHz 1850 1990 MHz 1920 2170 MHz +45, 45 2 x 17.8 dBi Horizontal: 66 Vertical: 5.2 0 6 +45, 45 2 x 18.2 dBi Horizontal: 65 Vertical: 5.0 0 6 +45, 45 2 x 18.3 dBi Horizontal: 63 Vertical: 4.7 0 6
0 ... 5 ... 10 T 0 ... 5 ... 10 T 0 ... 3 ... 6 T 0 ... 3 ... 6 T 0 ... 3 ... 6 T 16 ... 16 ... 17 dB 18 ... 18 ... 18 dB 14 ... 13 ... 13 dB 18 ... 17 ... 14 dB 18 ... 17 ... 14 dB > 27 dB Typically: 20 dB > 10 dB > 30 dB > 25 dB Typically: 20 dB > 10 dB > 30 dB 50 < 1.5 > 25 dB Typically: 16 dB > 10 dB > 30 dB 50 < 1.5 > 25 dB Typically: 18 dB > 10 dB > 30 dB 50 < 1.5 < 150 dBc 200 W (at 50 C ambient temperature) > 25 dB Typically: 18 dB > 10 dB > 30 dB 50 < 1.5 XXPol Dual-b. 824 960 +45 1710 2170 +45 7-16 7-16 4 x 7-16 female Bottom 2x, Position bottom continuously adjustable 23 kg Frontal: Lateral: Rearside: 340 N (at 150 km/h) 280 N (at 150 km/h) 640 N (at 150 km/h) 200 km/h 2215 x 302 x 192 mm 1916 / 262 / 139 mm 105
> 50 dB (824 960 // 1710 2170 MHz)

65
125
10
10 3 0
0 10
1710 2170 45
dB
824 960 45
dB
7-16 Vertical Pattern 0.59.5 electrical downtilt
7-16
Horizontal Pattern
Mechanical specifications Input Connector position Adjustment mechanism Weight

65
120
5
10 10
Wind load
dB
3 0
3 0
dB
Horizontal Pattern
824 960 X 65 07
1710 2170 X 65 0 6

XXPol A-Panel 824960/17102170 65/ 65 17/18.5dBi 07/06T
Type No. Frequency range Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Cross polar ratio Maindirection Sector Isolation: Intrasystem Isolation: Intersystem Impedance VSWR XXPol Dual-b. Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input 50 < 1.5 < 150 dBc 250 W 0 60 824960 824 894 MHz 880 960 MHz +45, 45 2 x 16.5 dBi Horizontal: 68 Vertical: 8.1 0.57 +45, 45 2 x 17 dBi Horizontal: 65 Vertical: 7.5 0.57
742 266
17102170 1710 1880 MHz 1850 1990 MHz 1900 2170 MHz +45, 45 2 x 17.8 dBi Horizontal: 66 Vertical: 5.2 0 6 +45, 45 2 x 18.2 dBi Horizontal: 65 Vertical: 5.0 0 6 +45, 45 2 x 18.5 dBi Horizontal: 63 Vertical: 4.7 0 6
0 ... 4 ... 7 T 0 ... 4 ... 7 T 0 ... 3 ... 6 T 0 ... 3 ... 6 T 0 ... 3 ... 6 T 16 ... 16 ... 14 dB 16 ... 16 ... 14 dB 13 ... 13 ... 13 dB 16 ... 15 ... 14 dB 15 ... 15 ... 15 dB > 28 dB Typically: 20 dB > 10 dB > 30 dB > 28 dB Typically: 20 dB > 10 dB > 30 dB 50 < 1.5 > 25 dB Typically: 16 dB > 10 dB > 30 dB 50 < 1.5 > 25 dB Typically: 18 dB > 10 dB > 30 dB 50 < 1.5 < 150 dBc 200 W (at 50 C ambient temperature) > 25 dB Typically: 20 dB > 10 dB > 30 dB 50 < 1.5
> 50 dB (824960 // 17102170 MHz)

65
125
7.5
10 3 0
10
1710 2170 45
dB
824 960 45
824 960 +45
1710 2170 +45
dB
3 0
7-16 Vertical Pattern 0.57 electrical downtilt
7-16
7-16
7-16
Horizontal Pattern
Mechanical specifications Input Connector position Adjustment mechanism Weight 4 x 7-16 female Bottom 2x, Position bottom continuously adjustable 26 kg Frontal: Lateral: Rearside: 460 N (at 150 km/h) 380 N (at 150 km/h) 860 N (at 150 km/h) 200 km/h 2815 x 302 x 192 mm 2516 / 262 / 139 mm

65 5
120
Wind load
10
10
dB
3 0
3 0
dB
Horizontal Pattern
106
Summary Directional Antennas Triple-band UMTS

Dual Polarization + 45/ 45 800/900 1800/1900 2000
XXXPol A-Panel
806 960 17101880 19202170 806 960 17101880 19202170 806 960 17101880 19202170 824 960 17102170 17102170
66 66 65 67 65 65 66 67 65 65 65 65
15dBi 16.5dBi 17dBi 16.5dBi 17.5dBi 18dBi 17.5dBi 17.5dBi 18dBi 17dBi 17dBi 16.5dBi
012T 08T 08T 010T 06T 06T 07T 06T 06T 07T 08T 08T
742 270
108
XXXPol A-Panel
742 271
2058
109
XXXPol A-Panel
742 272
2628
110
XXXPol A-Panel
742 241
2628
111
New Products
107
UMTS XXXPol
Triple-band A-Panel Dual Polarization Half-power Beam Width Adjust. Electr. Downtilt
806 960 1710 1880 1920 2170 X 66 0 1 2 X 66 0 8 X 65 0 8

XXXPol A-Panel 806960/17101880/19202170 66/ 66/65 15/16.5/17dBi 012/08/08T
Type No. Frequency range 806 866 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Cross polar ratio Maindirection Sector Isolation: Intrasystem Isolation: Intersystem 50 < 1.5 0 60 +45, 45 2 x 14.8 dBi Horizontal: 69 Vertical: 14.3 0.5 12 806 960 824 894 MHz +45, 45 2 x 15 dBi Horizontal: 68 Vertical: 14 0.5 12 880 960 MHz +45, 45 2 x 15.2 dBi Horizontal: 66 Vertical: 13.3 0.5 12
742 270
1710 1880 +45, 45 2 x 16.5 dBi Horizontal: 66 Vertical: 7.1 0.5 8 1920 2170 +45, 45 2 x 17.2 dBi Horizontal: 65 Vertical: 6.5 0 8 1710 1880 MHz 1920 2170 MHz
0 ... 6 ... 12 T 0 ... 6 ... 12 T 0 ... 6 ... 12 T 0 ... 4 ... 8 T 0 ... 4 ... 8 T 13 ... 12 ... 10 dB 14 ... 14 ... 14 dB 16 ... 16 ... 16 dB 17 ... 16 ... 15 dB 17 ... 15 ... 13 dB > 27 dB Typically: 25 dB > 10 dB > 30 dB > 27 dB Typically: 25 dB > 10 dB > 30 dB > 27 dB Typically: 25 dB > 10 dB > 30 dB > 23 dB Typically: 18 dB > 10 dB > 30 dB > 23 dB Typically: 20 dB > 10dB > 30 dB
> 50 dB (806 960 // 1710 1880 MHz)11 > 50 dB (806 960 // 1920 2170 MHz)11 > 30 dB (1710 1880 // 1920 2170 MHz) 50 < 1.5 < 150 dBc 50 < 1.5 50 < 1.5 < 150 dBc 50 < 1.5 < 150 dBc 200 W

130 66 14
10 3 0
10
dB
3 0
dB
Horizontal Pattern
806 960 45 1920 2170 1920 2170 +45 45
806 960 +45 1710 1880 1710 1880 +45 45

125 66
7.1
7-16
7-16
7-16 7-16
7-16
7-16
10 3 0
10
dB
dB
3 0
Input Connector position Adjustment mechanism Weight
6 x 7-16 female Bottom 3 x, Position bottom continuously adjustable 25 kg Frontal: Lateral: Rearside: 260 N (at 150 km/h) 210 N (at 150 km/h) 580 N (at 150 km/h) 200 km/h 1819 x 304 x 204 mm 1498 / 262 / 149 mm
Horizontal Pattern

120 65 6.5
Wind load
10
10

dB
dB
3 0
3 0
Horizontal Pattern
108
806 960 1710 1880 1920 2170 X 67 0 10 X 65 0 6 X 65 0 6

XXXPol A-Panel 806960/17101880/19202170 67/ 65/65 16.5/17.5/18dBi 010/06/06T
Type No. Frequency range 806 866 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Cross polar ratio Maindirection Sector Isolation: Intrasystem Isolation: Intersystem 50 < 1.5 +45, 45 2 x 16 dBi Horizontal: 69 Vertical: 11 0 10 806960 824 894 MHz +45, 45 2 x 16.1 dBi Horizontal: 68 Vertical: 10.7 0 10 880 960 MHz +45, 45 2 x 16.3 dB Horizontal: 67 Vertical: 9.8 0 10
742 271
17101880 +45, 45 2 x 17.5 dBi Horizontal: 65 Vertical: 5.1 0 6 19202170 +45, 45 2 x 18 dBi Horizontal: 65 Vertical: 4.8 0 6 1710 1880 MHz 1920 2170 MHz
0 ... 5 ... 10 T 0 ... 5 ... 10 T 0 ... 5 ... 10 T 0 ... 3 ... 6 T 0 ... 3 ... 6 T 15 ... 15 ... 13 dB 15 ... 15 ... 13 dB 15 ... 15 ... 13 dB 14 ... 15 ... 16 dB 14 ... 14 ... 14 dB > 25 dB Typically: 25 dB > 10 dB > 30 dB > 25 dB Typically: 25 dB > 10 dB > 30 dB > 25 dB Typically: 25 dB > 10 dB > 30 dB > 24 dB Typically: 18 dB > 10 dB > 30 dB > 25 dB Typically: 20 dB > 10 dB > 30 dB

130
10
10 3 0
10
dB
3 0
dB
806 960 45 1920 2170 1920 2170 +45 45
806 960 +45 1710 1880 1710 1880 +45 45
Horizontal Pattern

125 65
7-16
5.1
7-16
7-16 7-16
7-16
7-16
10 3 0 0 10
dB
dB
6 x 7-16 female Bottom 3 x, Position bottom continuously adjustable 33 kg Frontal: Lateral: Rearside: 370 N (at 150 km/h) 300 N (at 150 km/h) 820 N (at 150 km/h) 200 km/h 2379 x 304 x 204 mm 2058 / 262 / 149 mm
Horizontal Pattern

120 65
4.8
10
10
dB
3 0
3 0
Horizontal Pattern
dB
XXXPol
67
806 960 1710 1880 1920 2170 X 66 07 X 67 0 6 X 65 0 6

XXXPol A-Panel 806960/17101880/19202170 66/ 67/65 17.5/17.5/18dBi 07/06/06T
Type No. Frequency range 806 866 MHz Polarization Gain Half-power beam width Copolar +45/ 45 Electrical tilt continuously adjustable Sidelobe suppression for first sidelobe above horizon Front-to-back ratio, copolar Cross polar ratio Maindirection Sector Isolation: Intrasystem Isolation: Intersystem 50 < 1.5 +45, 45 2 x 17 dBi Horizontal: 69 Vertical: 7.8 0.5 7 806960 824 894 MHz +45, 45 2 x 17.2 dBi Horizontal: 68 Vertical: 7.4 0.5 7 880 960 MHz +45, 45 2 x 17.5 dBi Horizontal 66 Vertical: 7 0.5 7
742 272
17101880 +45, 45 2 x 17.5 dBi Horizontal: 67 Vertical: 5.2 0 6 19202170 +45, 45 2 x 18 dBi Horizontal: 65 Vertical: 4.8 0 6 1710 1880 MHz 1920 2170 MHz
0 ... 4 ... 7 T 0 ... 4 ... 7 T 0 ... 4 ... 7 T 0 ... 3 ... 6 T 0 ... 3 ... 6 T 15 ... 15 ... 14 dB 15 ... 15 ... 14 dB 15 ... 15 ... 15 dB 14 ... 14 ... 14 dB 14 ... 14 ... 14 dB > 25 dB Typically: 25 dB > 10 dB > 30 dB > 25 dB Typically: 25 dB > 10 dB > 30 dB > 25 dB Typically: 25 dB > 10 dB > 30 dB > 25 dB Typically: 18 dB > 10 dB > 30 dB > 25 dB Typically: 20 dB > 10 dB > 30 dB

XXXPol
130 66
7.5
10 3 0
10
dB
3 0
dB
806 960 45 1920 2170 1920 2170 +45 45
806 960 +45 1710 1880 1710 1880 +45 45
Horizontal Pattern
Vertical Pattern 0.57 electrical downtilt

125 67
7-16
5.2
7-16
7-16 7-16
7-16
7-16
10 3 0 0 10
dB
dB
6 x 7-16 female Bottom 3 x, Position bottom continuously adjustable 40 kg Frontal: 480 N (at 150 km/h) Lateral: 390 N (at 150 km/h) Rearside: 1060 N (at 150 km/h) 200 km/h 2949 x 304 x 204 mm 2628 / 262 / 149 mm
Horizontal Pattern

120 65
4.8
10
10
dB
3 0
3 0
Horizontal Pattern
110
dB
Triple-multiband A-Panel Dual Polarization Half-power Beam Width Adjust. Electr. Downtilt
824 960 1710 2170 1710 2170 X 65 07 X 65 0 8 X 65 0 8

XXXPol A-Panel 824960/17102170/17102170 65/ 65/65 17/17/16.5dBi 07/08/08T
Type No. Frequency range 824960 824 894 MHz 880 960 MHz +45, 45 +45, 45 2 x 16.5 dBi 2 x 17 dBi
742 241
17102170 17102170 1710 1880 MHz 1850 1990 MHz 1920 2170 MHz +45, 45 +45, 45 +45, 45 2 x 16.5 dBi 2 x 16 dBi Horizontal: 65 Vertical: 7.8 0 8 2 x 16.8 dBi 2 x 16.3 dBi Horizontal: 65 Vertical: 7.3 0 8 2 x 17 dBi 2 x 16.5 dBi Horizontal: 63 Vertical: 6.8 0 8
Polarization Gain: 824960 MHz 17102170 MHz (Syst. 1) 17102170 MHz (Syst. 2) Half-power beam width Horizontal: 68 Copolar +45/ 45 Vertical: 8.1 Electrical tilt 0.57 continuously adjustable Sidelobe suppression for 0 ... 4 ... 7 T first sidelobe above horizon 16 ... 16 ... 14 dB Front-to-back ratio, copolar > 26 dB Cross polar ratio Typically: Maindirection 0 20 dB Sector 60 > 10 dB Isolation: Intrasystem > 30 dB Isolation: Intersystem Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input
Horizontal: 65 Vertical: 7.5 0.57
0 ... 4 ... 7 T 0 ... 4 ... 8 T 0 ... 4 ... 8 T 0 ... 4 ... 8 T 16 ... 16 ... 14 dB 14 ... 14 ... 14 dB 16 ... 16 ... 15 dB 15 ... 16 ... 15 dB > 26 dB > 25 dB > 25 dB > 25 dB Typically: Typically: Typically: Typically: 20 dB 16 dB 18 dB 20 dB > 10 dB > 10 dB > 10 dB > 10 dB > 30 dB > 30 dB > 30 dB > 30 dB > 50 dB (824 960 // 1710 2170 MHz)11 > 38 dB (1710 2170 // 1710 2170 MHz) 50 50 50 50 50 < 1.5 < 1.5 < 1.5 < 1.5 < 1.5 < 150 dBc < 150 dBc 250 W 200 W (at 50 C ambient temperature)

125
7.5
10 3 0
10
dB
3 0
dB
824 960 45 1710 2170 1710 2170 +45 45
824 960 +45 1710 2170 1710 2170 +45 45
Horizontal Pattern
Vertical Pattern 0.57 electrical downtilt

125 65
7-16
7.8
7-16
7-16 7-16
7-16
7-16
10 3 0 0 10
dB
dB
6 x 7-16 female Bottom 3 x, Position bottom continuously adjustable 34 kg Frontal: 480 N (at 150 km/h) Lateral: 390 N (at 150 km/h) Rearside: 1060 N (at 150 km/h) 200 km/h 2944 x 304 x 204 mm 2628 / 262 / 149 mm
Horizontal Pattern

115 63 6.8
10
10
dB
3 0
3 0
dB
111
XXXPol
65
112
Summary Directional Antennas Vertical Polarization Single-band and Multi-band UMTS

Type Type No. Height [mm] 310 310 300 982 1302 328 Page
VPol BiDir VPol BiDir VPol LogPer VPol F-Panel Vpol F-Panel VVPol F-Panel
824960/17102170 824960/17102170 8062170 19202170 17102170 824960 17102170 824960 17102170 1920210 C
65 65 65 60 65 90 90 90 90 120
5dBi 5dBi 11dBi 17.5dBi 18dBi 7dBi 7dBi 10dBi 11.5dBi 14.5dBi 010T
738 445 738 446 742 192 741 415 742 445 742 290
114 114 115 116 117 118
VVPol F-Panel
800 10046
662
119
VPol F-Panel
741 786 New Products
982
120
113
UMTS VPol
Multi-band Bidirectional Antenna Vertical Polarization Half-power Beam Width
824 960/1710 2170 V 65
VPol BiDir 824960/17102170 65 5dBi

Type No. Input Frequency range VSWR Gain
738 445
1 x 7-16 female < 1.5
738 446
1 x N female
824 960 MHz, 1710 2170 MHz
372 mm 8.5 mm
Impedance Polarization Max. power (total) Weight Wind load Frontal: Lateral: Rearside:
50 Vertical 200 W (at 50 C ambient temperature) 0.8 kg 25 N (at 150 km/h) 65 N (at 150 km/h) 35 N (at 150 km/h) 200 km/h 422 x 212 x 95 mm 310 / 55 / 190 mm Radiator: Tin plated copper. Reflector: Weather-proof aluminum. Radome: High impact plastic, colour: Grey. All screws and nuts: Stainless steel. Wall mounting: No additional mounting kit needed. For pipe mast mounting use clamps listed on the datasheet (order separately). The radiating system is protected by the radome. Due to its very sturdy construction, the antenna remains operational even under icy conditions. All metal parts of the antenna as well as the inner conductor are DC grounded.
Mounting:
Ice protection:
Grounding:
10
3 0
Typical Horizontal Pattern
114
dB
400 mm
824 960 MHz: 5 dBi 1710 1880 MHz: 5.5 dBi 1880 2170 MHz: 6.5 dBi
Logarithmic Periodic Vertical Polarization Half-power Beam Width
806 2170 V 65
VPol LogPer 8062170 65 11dBi

Type No. Input Connector position Frequency range VSWR Gain Impedance Polarization Front-to-back ratio Half-power Beam Width horizontal vertical Intermodulation IM3 (2 x 43 dBm carrier) Max. power Weight Wind load Frontal: Lateral: Rearside: 806 1000 MHz < 1.5 11 dBi 50 Vertical > 25 dB 65 55 < 150 dBc 300 W
742 192
1 x 7-16 female Bottom 1000 1700 MHz < 1.5 11.3 dBi 50 Vertical > 25 dB 55 50 < 150 dBc 1700 2170 MHz < 1.5 11.5 dBi 50 Vertical > 23 dB 50 45 < 150 dBc
250 W 200 W (at 50 C ambient temperature) 5.7 kg 20 N (at 150 km/h) 260 N (at 150 km/h) 30 N (at 150 km/h) 200 km/h 360 x 175 x 1000 mm 300 / 155 / 785 mm
Radiator: Weather-proof aluminum. Reflector screen: Weather-proof aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. The antenna can be mounted on tubular mast with a diameter of 30 70 mm with supplied clamps. Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. All metal parts of the antenna as well as the inner conductor are DC grounded.
Mounting:
Ice protection:
Grounding:
806 1000 MHz

65 55
1700 2170 MHz

50 45
10 dB
10 dB
10 dB
10 dB
3 0
3 0
3 0
3 0
Horizontal Pattern
Vertical Pattern
Horizontal Pattern
Vertical Pattern
115
VPol
1920 2170 V 60

Type No. Frequency range Polarization Gain Half-power beam width Front-to-back ratio Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power
741 415
1920 2170 MHz Vertical 17.5 dBi H-plane: 60 E-plane: 8 > 25 dB 50 < 1.5 < 150 dBc 200 W (at 50 C ambient temperature)
110
60
VPol
10
3 0
Horizontal Pattern Mechanical specifications Input Connector position* Weight

8
dB
7-16 female Bottom or top 3.7 kg Frontal: Lateral: Rearside: 190 N (at 150 km/h) 40 N (at 150 km/h) 230 N (at 150 km/h) 200 km/h 1084 x 172 x 62 mm 982 / 155 / 36 mm
Wind load
10
3 0
dB
Vertical Pattern
116
Multi-band F-Panel Vertical Polarization Half-power Beam Width Adjust. Electrical Downtilt
1710 2170 V 65 0 10
VPol F-Panel 17102170 65 18dBi 010T

Type No. Frequency range 1710 1880 MHz Polarization Gain Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above horizon Front-to-back ratio Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power Vertical 17.5 dBi Horizontal: Vertical: 68 7
742 445
17102170 1850 1990 MHz Vertical 17.9 dBi Horizontal: 65 Vertical: 6.7 1920 2170 MHz Vertical 18.1 dBi Horizontal: 63 Vertical: 6.5
0 10 0 10 0 10 continuously adjustable continuously adjustable continuously adjustable 0 ... 5 ... 10 T 18 ... 16 .... 13 dB > 25 dB 50 < 1.5 0 ... 5 ... 10 T 18 ... 17 ... 14 dB > 25 dB 50 < 1.5 < 150 dBc 300 W (at 50 C ambient temperature) 0 ... 5 ... 10 T 18 ... 17 ... 14 dB > 25 dB 50 < 1.5
1710 1880 MHz

130 68
7
10 3 0 0 10
dB
Horizontal Pattern
1850 1990 MHz

125 65 6.7
1710 2170 VPol
10 3 0
10
dB
3 0
dB
Horizontal Pattern
1920 2170 MHz

120 63 6.5
Max. wind velocity

10 10
Packing size
dB
dB
3 0
3 0
Height/width/depth
Horizontal Pattern
Vertical Pattern 0 10 electrical downtilt continuously adjustable 117
VPol
dB
Dual-band F-Panel Vertical Polarization Half-power Beam Width Integrated Combiner
824 960 V 90
1710 2170 V 82 C
VVPol F-Panel 824960/17102170 C 90/82 7/7dBi

742 290
824 960 MHz Vertical 7 dBi Horizontal: Vertical: > 18 dB 50 90 60 1710 2170 MHz Vertical 7 dBi Horizontal: Vertical: > 20 dB 50 82 70
< 1.7 (824 960 MHz) < 1.7 (1710 2170 MHz) < 1.5 (870 960 MHz) < 1.5 (1710 1990 MHz) < 150 dBc < 150 dBc
824 960
90
824 960 VPol

60
1710 2170 VPol C 7-16
VPol
180
10
10 3 0
dB
Horizontal Pattern
1710 2170
82 170
dB
Input Connector position

70
Weight Wind load
10
Max. wind velocity

dB
10 3 0
dB
3 0
Horizontal Pattern
Vertical Pattern
118
Dual-band F-Panel Vertical Polarization Half-power Beam Width Integrated Combiner
824 960 V 90
1710 2170 V 82 C
VVPol F-Panel 824960/17102170 C 90/82 10/11dBi

800 10046
824 960 MHz Vertical 10 dBi Horizontal: Vertical: > 18 dB 50 < 1.7 (824 960 MHz) < 1.5 (870 960 MHz) < 150 dBc 90 33 1710 2170 MHz Vertical 11 dBi Horizontal: Vertical: > 20 dB 50 < 1.5 < 150 dBc 82 19
824 960
90 180 33
824 960 VPol C
1710 2170 VPol VPol 1 x 7-16 female Bottom 4.4 kg 65 N (at 150 km/h) 50 N (at 150 km/h) 160 N (at 150 km/h) 200 km/h 744 x 172 x 92 mm 662 / 155 / 69 mm 119
7-16
10 10
dB dB
3 0
3 0
Horizontal Pattern
1710 2170
82 170
Input Connector position Weight Wind load

19
Frontal: Lateral: Rearside:
10
Max. wind velocity

dB
10 3 0
dB
3 0
Horizontal Pattern
Vertical Pattern
1920 2170 V 120
VPol F-Panel 19202170 120 14.5dBi

741 786
1920 2170 MHz Vertical 14.5 dBi H-plane: 120 E-plane: 8 > 18 dB 50 < 1.5 < 150 dBc 200 W (at 50 C ambient temperature)
120
215
VPol
10
3 0
Horizontal Pattern Mechanical specifications Input Connector position* Weight

8
dB
7-16 female Bottom or top 3.7 kg Frontal: Lateral: Rearside: 180 N (at 150 km/h) 80 N (at 150 km/h) 230 N (at 150 km/h) 200 km/h 1084 x 172 x 72 mm 982 / 155 / 49 mm
Wind load
10
3 0
dB
Vertical Pattern
120
Summary Omnidirectional Antennas 800/900/1800/2000

Type Type No. Connector Height female [mm] N N N 7-16 7-16 7-16 7-16 180 273 635 1543 3237 3033 2954 Remarks Page
VPol Omni VPol Omni VPol Omni VPol Omni VPol Omni VPol Omni VPol Omni
870960 806960 890960 870960 806894 870960 870960
360 360 360 360 360 360
2 dBi 2 dBi 5 dBi 8 dBi 11 dBi 11 dBi 5T
738 450 K 75 11 61 K 75 15 64 1 736 350 738 192 736 347 736 349
indoor/outdoor 122 123 124 125 126 127 128
360 10.5 dBi
Vertical Polarization Dual-band

VPol Omni VPol Omni 870960/17101880 360 824960/18052170 360 2 dBi 2 dBi 2 dBi 2 dBi 2 dBi 2 dBi 738 449 800 10147 741 862 N N N 216 216 493 indoor/outdoor 129 indoor/outdoor 130 seperate inputs seperate inputs 131
VVPol Omni 870960/17101880 360 870960/17101880 360 VVPol Omni 870960/17101880 360 19202170 360
800 10111
493
132
Vertical Polarization 1800

VPol Omni VPol Omni VPol Omni 17101880 17101880 17101880 360 360 360 8 dBi 11 dBi 11 dBi 739 785 738 187 737 190 7-16 7-16 7-16 800 1570 1560 133 134 135
6T

VPol Omni VPol Omni 17102170 19202170 360 360 2 dBi 11 dBi 738 454 741 790 N 7-16 115 1387 indoor/outdoor 136 137
121
Omni VPol
Omnidirectional Antenna Vertical Polarization Indoor and outdoor use
870 960 V
VPol Omni 870960 360 2dBi

Type No. Input Connector position Frequency range VSWR Gain Impedance Intermodulation IM3 (2 x 43 dBm carrier) Polarization Max. power Weight Radome diameter Height Material:
738 450
N female Bottom or top 870 960 MHz < 1.5 2 dBi 50 < 150 dBc Vertical 100 Watt (at 50 C ambient temperature) 200 g 20 mm 180 mm Radiator: Brass. Radome: Fiberglass, colour: White. One hole mounting (16 mm diameter) to surfaces of max. 10 mm thickness. All metal parts of the antenna as well as the inner conductor and the mounting kit are DC grounded. 180 mm
Mounting:
Grounding:
78
10
3 0
Vertical Pattern
122
dB
Omnidirectional Antennas Vertical Polarization
806 960 V

Type No. Frequency range Polarization Gain Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power Mounting:
K 75 11 61
806 960 MHz Vertical 2 dBi 348 mm 50 < 1.5 < 150 dBc 100 W (at 50 C ambient temperature) The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of a tubular mast of 40 54 mm diameter (connecting cable runs inside the mast). 2. Laterally at the tip of a tubular mast of 20 54 mm diameter (connecting cable runs outside the mast). Radiator: Brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. All metal parts of the antenna as well as the inner conductor and the mounting kit are DC grounded.
Material:
Grounding:
78
10
3 0
Vertical Pattern
Mechanical specifications Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size On the tip Laterally at the tip Height N female Bottom 0.74 kg 21 mm 17 N (at 150 km/h) 200 km/h 455 x 112x 97 mm 348 mm
Brackets for side mounting (see page 198 200)
123
VPol
dB
890 960 V

K 75 15 64 1
890 960 MHz Vertical 5 dBi 50 < 1.5 < 150 dBc 250 W (at 50 C ambient temperature) The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of a tubular mast of 40 54 mm diameter (connecting cable runs inside the mast). 2. Laterally at the tip of a tubular mast of 20 54 mm diameter (connecting cable runs outside the mast). Radiator: Brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. All metal parts of the antenna as well as the inner conductor and the mounting kit are DC grounded. 715 mm N female Bottom 0.90 kg 21 mm 20 N (at 150 km/h) 200 km/h 825 x 112 x 97 mm 715 mm Brackets for side mounting (see page 198 200)
Material:
Grounding:
30
10
VPol
3 0
Vertical Pattern
dB
Mechanical specifications Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size On the tip Laterally at the tip Height
124
870 960 V

736 350
870 960 MHz Vertical 8 dBi 50 < 1.5 < 150 dBc 500 W (at 50 C ambient temperature) The antenna can be attached laterally at the tip of a tubular mast of 50 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. From the solid metal tip right down to the base of the high gain antennas the grounding crosssection is 22 mm2 copper or more, exceeding EN 50083-1. The inner conductor is coupled capacitively. 1543 mm
Material:
Excellent grounding:
13
10
3 0
dB
Vertical Pattern
um maxim p to mast
736 350 7-16 female Bottom 5.5 kg 51 mm 130 N (at 150 km/h) 200 km/h 1846 x 148 x 112 mm 1543 mm

230
Weight Radome diameter Wind load Max. wind velocity Packing size
150
104
Height
125
VPol
806 894 V

738 192
806 894 MHz Vertical 11 dBi 50 < 1.5 < 150 dBc 500 W (at 50 C ambient temperature) The antenna can be attached laterally at the tip of a tubular mast of 50 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. From the solid metal tip right down to the base of the high gain antennas the grounding crosssection is 22 mm2 copper or more, exceeding EN 50083-1. The inner conductor is coupled capacitively. 3237 mm 7-16 female Bottom 8.5 kg 51 mm 230 N (at 150 km/h) 180 km/h 3516 x 148 x 112 mm 3237 mm Brackets for side mounting (see page 198 200)
Material:
10 3
VPol
Vertical Pattern
dB
um maxim p to mast

230
150
104
Height
126
870 960 V

736 347
870 960 MHz Vertical 11 dBi 50 < 1.5 < 150 dBc 500 W (at 50 C ambient temperature) The antenna can be attached laterally at the tip of a tubular mast of 50 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. From the solid metal tip right down to the base of the high gain antennas the grounding crosssection is 22 mm2 copper or more, exceeding EN 50083-1. The inner conductor is coupled capacitively. 3033 mm
Material:
10 3 0
dB
Vertical Pattern
um maxim p to mast
736 347 7-16 female Bottom 8 kg 51 mm 210 N (at 150 km/h) 200 km/h 3316 x 148 x 112 mm 3033 mm

230
150
104
Height
127
VPol
Omnidirectional Antennas Vertical Polarization Fixed Electrical Downtilt
870 960 V 5
VPol Omni 870960 360 10.5dBi 5T

Type No. Frequency range Polarization Gain Electrical tilt Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power Mounting:
736 349
870 960 MHz Vertical 10.5 dBi 5, fixed 50 < 1.5 < 150 dBc 500 W (at 50 C ambient temperature) The antenna can be attached laterally at the tip of a tubular mast of 50 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. From the solid metal tip right down to the base of the high gain antennas the grounding crosssection is 22 mm2 copper or more, exceeding EN 50083-1. The inner conductor is coupled capacitively. 2954 mm 736 349 7-16 female Bottom 8 kg 51 mm 210 N (at 150 km/h) 200 km/h 3316 x 148 x 112 mm 2954 mm Brackets for side mounting (see page 198 200)
Material:
10 3
VPol
dB
um maxim p to mast

230
150
104
Height
128
Dual-band Omni Antenna Vertical Polarization Indoor and outdoor use
870 960 / 17101880 V
VPol Omni 870960/17101880 360 2dBi

Type No. Input Connector position Frequency range VSWR Gain Impedance Intermodulation IM3 (2 x 43 dBm carrier) Polarization Max. power
738 449
1 x N female Bottom or top 870 960 MHz / 1710 1880 MHz < 1.7 2 dBi 50 < 150 dBc Vertical 50 Watt: 870 960 MHz 50 Watt: 1710 1880 MHz (at 50 C ambient temperature) 250 g 20 mm 216 mm Radiator: Brass. Radome: Fiberglass, colour: White. One hole mounting (16 mm diameter) to surfaces of max. 10 mm thickness.
Weight Radome diameter Height Material:
Mounting:
78
10
216 mm
3 0
Vertical Pattern
129
VPol
dB
824 960 /1805 2170 V
VPol Omni 824960/18052170 360 2dBi

Type No. Input Connector position Frequency range VSWR Gain Impedance Polarization Max. power
800 10147
1 x N female Bottom or top 824 960 MHz / 1805 2170 MHz < 2.0 2 dBi 50 Vertical 50 Watt: 824 960 MHz 50 Watt: 1805 2170 MHz (at 50 C ambient temperature) 250 g 20 mm 216 mm Radiator: Brass. Radome: Fiberglass, colour: White. One hole mounting (16 mm diameter) to surfaces of max. 10 mm thickness. All metal parts of the antenna as well as the inner conductor and the mounting kit are DC grounded. 216 mm
Mounting:
Grounding:
78
10
VPol
3 0
Vertical Pattern
130
dB
Dual-band Omni Antenna Vertical Polarization
870 960 17101880 V
870 960 17101880 V
VVPol Omni 870960/17101880 360/360 2/2dBi

Type No. Frequency range
741 862
Upper unit 870 960 MHz 1710 1880 MHz Vertical 2 dBi > 25 dB 50 < 1.8 < 150 dBc 50 W (at 50 C ambient temperature) Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit and screws: Stainless steel. The antenna can be attached laterally at the tip of a tubular mast of 40 70 mm diameter with a mounting clamp supplied with the antenna. The connecting cables (not supplied) run outside the mast. The metal parts of the antenna and the mounting kit (exclusive the inner conductor of the upper unit) are DC grounded. Lower unit 870 960 MHz 1710 1880 MHz Vertical 493 mm 870 960 17101880 870 960 17101880 N
dB
Polarization Gain Isolation, between ports Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Material:
2 dBi > 25 dB 50 < 1.8
Mounting:
78
10
3 0
Vertical Pattern Mechanical specifications Input Connector position Weight Wind load Max. wind velocity Packing size Height Radome diameter 2 x N female Bottom 1.2 kg 30 N (at 150 km/h) 200 km/h 665 x 112 x 97 mm 496 mm 30 mm
Bottom view 131
VPol
130 mm
Multi-band Omni Antenna Vertical Polarization
870 960 1710 1880 V
1920 2170
VVPol Omni 870960/17101880/1920-2170 360/360 2/2dBi

Type No. Frequency range
800 10111
Upper unit 870 960 MHz 1710 1880 MHz Vertical 2 dBi > 25 dB 50 < 1.7 < 150 dBc 50 W (at 50 C ambient temperature) Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit and screws: Stainless steel. The antenna can be attached laterally at the tip of a tubular mast of 40 70 mm diameter with a mounting clamp supplied with the antenna. The connecting cables (not supplied) run outside the mast. The metal parts of the antenna and the mounting kit (exclusive the inner conductor of the upper unit) are DC grounded. Lower unit 1920 2170 MHz Vertical 493 mm 870 960 17101880 1920 2170 N
dB
Polarization Gain Isolation, between ports Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Material:
2 dBi > 25 dB 50 < 1.5
Mounting:
78
10
VPol
3 0
Vertical Pattern Mechanical specifications Input Connector position Weight Wind load Max. wind velocity Packing size Height Radome diameter 2 x N female Bottom 0.85 kg 30 N (at 150 km/h) 200 km/h 665 x 112 x 97 mm 493 mm 30 mm
Bottom view 132
130 mm
Omnidirectional Antenna Vertical Polarization
17101880 V

739 785
1710 1880 MHz Vertical 8 dBi 50 < 1.5 < 150 dBc 200 W (at 50 C ambient temperature) The antenna can be attached laterally at the tip of a tubular mast of 50 94 mm diameter with one U-bolt bracket supplied with the antenna (connecting cable runs outside the mast). Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. From the solid metal tip right down to the base of the high gain antennas the grounding crosssection is 22 mm2 copper or more, exceeding EN 50083-1. The inner conductor is coupled capacitively. 807 mm
Material:
13
10
3 0
dB
Vertical Pattern
um maxim p to mast
Input
130
7-16 female Bottom 4 kg 51 mm 90 N (at 150 km/h) 200 km/h 986 x 148 x 112 mm 807 mm
Connector position Weight Radome diameter
104
Wind load Max. wind velocity Packing size Height
133
VPol
17101880 V
VPol Omni 17101880 360 11dBi

738 187
1710 1880 MHz Vertical 11 dBi 50 < 1.3 < 150 dBc 200 W (at 50 C ambient temperature) The antenna can be attached laterally at the tip of a tubular mast of 50 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. From the solid metal tip right down to the base of the high gain antennas the grounding crosssection is 22 mm2 copper or more, exceeding EN 50083-1. The inner conductor is coupled capacitively. 1568 mm Mechanical specifications
um maxim p to mast
Material:
10
VPol
Vertical Pattern
dB
738 187 7-16 female Bottom 5.5 kg 51 mm 130 N (at 150 km/h) 200 km/h 1846 x 148 x 112 mm 1568 mm

230
150
104
Height
134
Omnidirectional Antenna Vertical Polarization Fixed Electrical Downtilt
17101880 V 6
VPol Omni 17101880 360 11dBi 6T

Type No. Frequency range Polarization Gain Electrical tilt Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power Mounting:
737 190
1710 1880 MHz Vertical 11 dBi 6, fixed 50 < 1.3 < 150 dBc 200 W (at 50 C ambient temperature) The antenna can be attached laterally at the tip of a tubular mast of 50 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. From the solid metal tip right down to the base of the high gain antennas the grounding crosssection is 22 mm2 copper or more, exceeding EN 50083-1. The inner conductor is coupled capacitively. 1560 mm
Material:
7
10
3 0
dB
um maxim p to mast

230
7-16 female Bottom 5.5 kg 51 mm 130 N (at 150 km/h) 200 km/h 1846 x 148 x 112 mm 1560 mm
150
104
Height
135
VPol
17102170 V

738 454
N female Bottom or top 1710 2170 MHz < 1.5 2 dBi 50 < 150 dBc Vertical 50 W (at 50 C ambient temperature) 150 g 20 mm 115 mm Radiator: Brass. Radome: Fiberglass, colour: White. One hole mounting (16 mm diameter) to surfaces of max. 10 mm thickness. All metal parts of the antenna and the mounting kit are DC grounded. The inner conductor is not DC grounded. 115 mm
Mounting:
Grounding:
78
10
VPol
3 0
Vertical Pattern
136
dB
Omnidirectional Antenna Vertical Polarization
19202170 V
VPol Omni 19202170 360 11dBi

741 790
1920 2170 MHz Vertical 11 dBi 50 < 1.5 < 150 dBc 150 W (at 50 C ambient temperature) The antenna can be attached laterally at the tip of a tubular mast of 50 94 mm diameter with one U-bolt bracket supplied with the antenna (connecting cable runs outside the mast). Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. From the solid metal tip right down to the base of the high gain antennas the grounding crosssection is 22 mm2 copper or more, exceeding EN 50083-1. The inner conductor is coupled capacitively. 1387 mm
Material:
10
3 0
dB
Vertical Pattern
um maxim p to mast
Input
130
7-16 female Bottom 5 kg 51 mm 120 N (at 150 km/h) 200 km/h 1570 x 148 x 112 mm 1387 mm
Connector position Weight Radome diameter
104
Wind load Max. wind velocity Packing size Height
137
VPol
138
Summary Indoor Antennas
Vertical Polarization Multi-band

Type Type No. Frequency range 824 960 MHz and 1710 2170 MHz 824 960 MHz and 1710 2170 MHz 1710 2500 MHz 824 960 MHz and 1425 2170 MHz 876 960 MHz and 1710 2500 MHz 824 960 MHz and 1425 2170 MHz 876 960 MHz and 1710 2500 MHz Connector female N Page
VPol BiDir 824960/17102170
65
5dBi
738 446
140
VPol Indoor 824960/17102170
90
7dBi
742 149
141
VPol Indoor 17102170 VPol Indoor 824960/14252170
360 360
2dBi 2dBi
741 573 741 572
N N
142 143
VPol Indoor 876960/17102500
360
2dBi
800 10137
143
VPol Indoor 824960/14252170
360
2dBi
800 10177
144
VPol Indoor 876960/17102500
360
2dBi
800 10173
144
Indoor / Outdoor Single-band

VPol Omni 870960 360 2dBi 738 450 870 960 MHz N 145
Indoor / Outdoor Dual-band / Multi-band

VPol Omni 870960/17101880 360 2dBi 738 449 870 960 MHz and 1710 1880 MHz 1710 2170 MHz N 146
VPol Omni 17102170
360
2dBi
738 454
147
139
Indoor VPol
Multi-band Bidirectional Antenna Vertical Polarization Half-power Beam Width
824 960/1710 2170 V 65
VPol BiDir 824960/17102170 65 5dBi

Type No. Input Frequency range VSWR Gain
738 446
1 x N female 824 960 MHz, 1710 2170 MHz < 1.5 824 960 MHz: 5 dBi 1710 1880 MHz: 5.5 dBi 1880 2170 MHz: 6.5 dBi 50 Vertical 200 W (at 50 C ambient temperature) 0.8 kg Frontal: Lateral: Rearside: 25 N (at 150 km/h) 65 N (at 150 km/h) 35 N (at 150 km/h) 200 km/h 422 x 212 x 95 mm 310 / 55 / 190 mm Radiator: Tin plated copper. Reflector: Weather-proof aluminum. Radome: High impact plastic, colour: Grey. All screws and nuts: Stainless steel. Wall mounting: No additional mounting kit needed. For pipe mast mounting use clamps listed on the datasheet (order separately). The radiating system is protected by the radome. Due to its very sturdy construction, the antenna remains operational even under icy conditions. All metal parts of the antenna as well as the inner conductor are DC grounded. 8.5 mm
372 mm
Impedance Polarization Max. power (total) Weight Wind load
Mounting:
Ice protection:
Grounding:
10
3 0
Typical Horizontal Pattern
140
dB
400 mm
Indoor Multi-b. Direct. Antenna Vertical Polarization Half-power Beam Width Integrated Combiner
824 960 V 90
1710 2170 V 90 C
VVPol Indoor 824960/17102170 90 7dBi

Type No. Frequency range Polarization Gain Half-power beam width Impedance VSWR Max. power Input Weight Packing size Height/width/depth Material:
742 149
824 960 MHz / 1710 2170 MHz Vertical 7 dBi Horizontal: 90 50 870 960 MHz and 1710 1900 MHz: < 1.6 824 960 MHz and 1710 2170 MHz: < 2.0 50 W (at 50 C ambient temperature) Cable RG 223/CU of 1m length, white, with N female connector 500 g 321 x 165 x 50 mm 205 / 155 / 42 mm
N
824 960 VPol C 1710 2170 VPol
Radiator: Brass. Radome: ABS, colour: White. Reflector: Aluminum. Mounting plates: Stainless steel. Two holes of 6 mm diameter in the mounting plate. All metal parts inclusive the inner conductor are DC grounded. Broadband power splitter (800 2500 MHz).
90
Mounting:
Grounding:
10 dB
Available accessories:
3 0
Horizontal Pattern
Mounting:
Mount the attachment plate to the wall using two screws of 4 mm diameter in the position as indicated.
Align the antenna over the attachment plate, keeping the cable in the middle of the plate.
Pull the antenna downwards until it clicks into place.
141
VPol
Indoor Omnidirectional Antenna Vertical Polarization Multi-band

q
1710 2500 V
The antenna can be operated in the total frequency range simultaneously. q The antenna needs no additional groundplane. VPol Indoor 17102500 360 2dBi
Type No. Frequency range VSWR
741 573
1710 2500 MHz 1710 1850 1920 2170 1880 1990 2170 2500 MHz: MHz: MHz: MHz: < < < < 1.6 1.6 1.6 2.0
100 mm dia.
Input Gain Impedance Polarization Max. power (per band) Weight Diameter Height Material:
1 x N female 2 dBi 50 Vertical 50 W (at 50 C ambient temperature) 150 g 100 mm 50 mm (without connector) Base: Aluminum. Protective housing: High impact polystyrol, colour: White. Additional painting is possible. Holes in the base enable a mounting on the ceiling. Screws are supplied. For the N connector a hole in the ceiling with a diameter of 35 mm is required. All metal parts including the inner conductor are DC grounded. Broadband power splitters and tappers (800 2500 MHz). min. dia. 35 mm N connector, female 2 holes dia. 5 mm
Mounting:
Grounding:
80 mm
VPol
12.9 mm
Clip the protective housing into position after the antenna has been mounted with the help of the three supplied screws.
142
Indoor Omnidirectional Antennas Vertical Polarization Multi-band

The antenna can be operated in all frequency ranges simultaneously. q The antennas need no additional groundplane.
q
800/2000/2500 V
741 572: VPol Indoor 824960/14252170 360 2dBi 800 10137: VPol Indoor 876960/17102500 360 2dBi
260 mm
741 572
824 960 MHz 1425 2170 MHz < 2.0: 824 960 MHz < 2.0: 1425 1710 MHz < 1.6: 1710 1990 MHz < 2.0: 1990 2170 MHz
800 10137
876 960 MHz 1710 2500 MHz < 1.9: 876 890 MHz < 1.6: 890 960 MHz < 1.6: 1710 2170 MHz < 2.0: 2170 2500 MHz
1 x N female 2 dBi 50 Vertical 50 W (at 50 C ambient temperature) 400 g 260 mm 300 g 210 mm 741 572
78 mm (without connector) Base: Aluminum. Protective housing: High impact polystyrol, colour: White. Additional painting is possible. Three holes in the base enable a mounting on the ceiling. Two types of screws are supplied. For the N connector a hole in the ceiling with a diameter of 35 mm is required. All metal parts including the inner conductor are DC grounded. Broadband power splitters and tappers (800 2500 MHz).
Mounting:
Grounding:
min. dia. 35 mm N connector, female
3 holes dia. 5 mm
dia. 160 mm
13 mm
143
VPol
Indoor Omnidirectional Antennas Vertical Polarization Multi-band

New pleasant design. The antenna can be operated in all frequency ranges simultaneously. q The antennas need no additional groundplane. 800 10177: VPol Indoor 824960/14252170 360 2dBi 800 10173: VPol Indoor 876960/17102500 360 2dBi
q q
800/2000/2500 V
265 mm
800 10177 800 10173

824 960 MHz 1425 2170 MHz < 2.0: 824 960 MHz < 2.0: 1425 1710 MHz < 1.6: 1710 1990 MHz < 2.0: 1990 2170 MHz 876 960 MHz 1710 2500 MHz < 1.8: 876 890 MHz < 1.6: 890 960 MHz < 1.6: 1710 2170 MHz < 2.0: 2170 2500 MHz
1 x N female 2 dBi 50 Vertical 50 W (at 50 C ambient temperature) 480 g 265 mm 340 g 215 mm 800 10177
85 mm (without connector) Base: Aluminum. Protective housing: High impact polystyrol, colour: White. Additional painting is possible. Three holes in the base enable a mounting on the ceiling. Two types of screws are supplied. For the N connector a hole in the ceiling with a diameter of 35 mm is required. All metal parts including the inner conductor are DC grounded. Broadband power splitters and tappers (800 2500 MHz).
Mounting:
Grounding:
min. dia. 35 mm N connector, female
VPol
3 holes dia. 5 mm
dia. 160 mm
13 mm
144
870 960 V

738 450
N female Bottom or top 870 960 MHz < 1.5 2 dBi 50 < 150 dBc Vertical 100 W (at 50 C ambient temperature) 200 g 20 mm 180 mm Radiator: Brass. Radome: Fiberglass, colour: White. One hole mounting (16 mm diameter) to surfaces of max. 10 mm thickness. All metal parts of the antenna as well as the inner conductor and the mounting kit are DC grounded. 180 mm
Mounting:
Grounding:
78
10
3 0
Vertical Pattern VPol 145
dB
870 960 / 17101880 V
VPol Omni 870960/17101880 360 2dBi

Type No. Input Connector position Frequency range VSWR Gain Impedance Intermodulation IM3 (2 x 43 dBm carrier) Polarization Max. power
738 449
1 x N female Bottom or top 870 960 MHz / 1710 1880 MHz < 1.7 2 dBi 50 < 150 dBc Vertical 50 W: 870 960 MHz 50 W: 1710 1880 MHz (at 50 C ambient temperature) 250 g 20 mm 216 mm Radiator: Brass. Radome: Fiberglass, colour: White. One hole mounting (16 mm diameter) to surfaces of max. 10 mm thickness.
Mounting:
78
10
3 0
Vertical Pattern VPol
146
dB
216 mm
17102170 V

738 454
N female Bottom or top 1710 2170 MHz < 1.5 2 dBi 50 < 150 dBc Vertical 50 W (at 50 C ambient temperature) 150 g 20 mm 115 mm Radiator: Brass. Radome: Fiberglass, colour: White. One hole mounting (16 mm diameter) to surfaces of max. 10 mm thickness. All metal parts of the antenna and the mounting kit are DC grounded. The inner conductor is not DC grounded. 115 mm
Mounting:
Grounding:
78
10
3 0
Vertical Pattern VPol 147
dB
148
Summary Remote Electrical Tilt (RET)
Type
Type No.
Page
RET-system Components Controlling the RCU Communication between OMC and CCU Browser Application Attachment of the RCU Instructions of Feederline Installation
F-Panel with four connectors arranged on two levels A-Panel with four connectors arranged on two levels Triple-band antennas with Kathrein installation tool
150
151
154
156
157
158 159 160
Datasheets of RET-components
Remote Control Unit (RCU) Central Control Unit (CCU) Power Supply and Signal Cable DC Power and Signal Splitter Lightning Protection Device Earthing Clamp Double Tower Mounted Amplifier Smart Bias Tee 860 10003 860 10006 / 860 10026 860 10007 860 10002 860 10030 860 10031 782 10147 / ..48 / ..49 782 10253 / ..54 / ..55 / ..56 161 162 163 164 165 166 167 168
149
RET
System for Remote Electrical Tilt (RET) RET-system Components
RCU (Remote Control Unit)
Remote controlled motor, mounted at the antenna and used to adjust the downtilt angle
CCU (Central Control Unit)
Controls several RCUs Provides power for connected devices; e.g. RCU, TMA and/or Smart Bias Tees Handles alarming Designed for indoor BTS installation
Control cable
Feeds power supply and control signals to the RCUs
DC power and signal splitter
Allocates power supply and control signals from a common input onto three outputs for multiple RCU-control
Lightning protection device
Protects the RET system against lightning Needs to be utilised if RCUs are controlled with separate cable
Earthing clamp
Grounds the control cable
Optional
TMA (Tower Mounted Amplifier) Installed to enhance coverage and improve voice quality Forwards power supply and control signals to connected RCUs
Smart Bias Tee
Employed to feed control signals and power supply onto the RF cables
150
System for Remote Electrical Tilt (RET) Controlling the RCU
Alarm interface OC
RS 232
Ethernet
RCU interface
DC power supply 48 V
AC power supply 110 240 V (optional)
The major component to control the RCU is the Central Control Unit (CCU), which is located at the BTS. In order to cover all required applications, the CCU can be accessed from the Operational Maintenance Center (OMC) via the Ethernet input and/or directly by a personal computer via the RS 232 input.
The number of RCUs and the maximum usable cable length, depend on power losses along the cables. Following, a summary of different examples is given about how to connect RCUs using separate cables:
XXPol Antenna
XXPol Antenna
Connection between CCU and RCU Three options may be offered: using Smart Bias Tees in the feeder lines via TMA
Max. cable length 150 m Max. cable length 25 m
RCU
RCU
Separate cables
Splitter
Utilising splitters up to nine RCUs may be connected to a single CCU.
Use of separate cables

RET
BTS
The 5-conductor cable consists of two wires for the HDLC data, two wires for the +29 V respectively +13 V power supplies and one for grounding.
CCU
Example to connect 3 RCUs with separate cables
XXPol Antenna RCU
151

Via feeder cable employing two Smart Bias
XXPol Antenna XXPol Antenna XXPol Antenna
Tees In order to reduce installation efforts and costs,
RCU
RCU
RCU
RCU
RCU
RCU
Kathrein offers a solution, which uses the feeder line to forward the control signal and the power supply up to the RCU.
Max. cable length 25 m
3:1 Splitter
3:1 Splitter
3:1 Splitter
One of Kathreins Smart Bias Tees is added into

Max. cable length 100 m 3:1 Splitter
the feeder line close to the base station. A second Smart Bias Tee is mounted near the antennas to recover the control signal and DC voltage from the feeder. Due to the use of the existing feeder line for the RCU controlling, there is no need to install a
CCU
BTS
separate cable with its own lightning protection system.
Example to connect 6 RCUs with separate cable
XXXPol Antenna
XXXPol Antenna
XXXPol Antenna
XXPol Antenna
XXPol Antenna
RCU
RCU
RCU
RCU
RCU
RCU
RCU
RCU
RCU
RCU
RCU
RCU
RCU
RCU
XXPol Antenna RCU
Splitter
Splitter Splitter Smart Bias-Tee
Splitter
Splitter
Splitter
3:1 Splitter
Feeder cable
RET
Smart Bias-Tee
3x
BTS UMTS
CCU
CCU
3x BTS GSM 1800
BTS
Example to connect 9 RCUs with separate cables 152
Example to connect 6 RCUs utilising two Smart Bias Tees

Via feeder cable utilising one Smart Bias Tee and one TMA Especially with UMTS, tower mounted amplifiers (TMA) are implemented to the system to enhance coverage and improve voice quality. An elegant way of controlling the RET system is to combine a Kathrein TMA and a RCU. Both, the control signal and DC power supply are fed onto the RF cable via a Smart Bias-Tee. The TMA includes a Smart Bias-Tee to recover signals and voltage from the feeder cable forwarding them to the connected RCUs. Each of the three CCU outputs is suitable for the connection of one TMA and max. 3 RCUs. Kathreins overall RET system works according the AISG standard. The AISG was founded in 2001 as a sub-group of the UMTS standardisation group 3GPP (3G Partnership Project). The purpose of the AISG standard is to embed the RET control into the UMTS standard and
XXPol Antenna XXPol Antenna XXPol Antenna
AISG (Antenna Interface Standards Group)
define all interfaces and protocols between the CCU and the RCU. The link between the OMC
RCU Max. cable length 25 m
RCU
RCU
RCU
RCU
RCU
and the BTS is not standardised by the AISG! Several antenna and TMA manufacturers (including Kathrein) as well as operators and OEMs are members of the AISG. The groups overall goal is to guarantee the basic interoperability of antennas and the control infrastructure.
Splitter
Splitter
Splitter
TMA
TMA
TMA
Feeder cable
Smart Bias-Tee
Smart Bias-Tee
Smart Bias-Tee
CCU
3x BTS UMTS
3x BTS GSM 1800
Example to connect 6 RCUs utilising Smart Bias Tees and TMAs
153
RET
System for Remote Electrical Tilt (RET) Communication between OMC and CCU
Overview of general CCU network integration
The electrical tilt can be controlled either locally or remotely. Local control: Configuration of the RET system and simple adaptation to network changes can be made via local control. In this case, an installation team has to be sent out to the site. A laptop is connected to the RS232 interface and PPP link at the CCU.
RET
pattern has to be adjusted much more often compared to a GSM network. To meet this demand, a remote controlled system via OMC is inevitable. The Ethernet interface may be selected for remote control in a local area network (LAN) or wide area network (WAN). The following transport and application protocols are served by the CCU: TCP/IP, PPP, UDP, DHCP, HTML and ICMP/Ping. In future, the CCU will also be able to support a selection from the application protocols: XML-RPC, FTP, Telnet, SNMP and NFS.
Alternatively, you may use the Ethernet interface. Remote control: Due to the required network optimisation with UMTS, the downtilt of the vertical radiation
154
It is also anticipated that the software of the CCU will be extended to allow the operation of a
System for Remote Electrical Tilt (RET) Communication between OMC and CCU
cablemodem or GSM-modem connected to the RS232 interface. The hardware interface RS232 on the CCU can Different ways to communicate with the CCU from the OMC (Operational Maintenance Center) can be chosen depending on the network connections implemented: be utilised to connect modems. If a fixed telephone line is available at the site, the link between the OMC and the CCU can be accomplished using cable modems on both sides. Connection via ethernet The base station transceivers on different sites are surveyed from the OMC via a supplier specific Ethernet connection. Kathrein is also using the medium Ethernet to address and control the CCU from the OMC.
Antenna CCU-Control
RS232
Connection via modems
Fixed Line
Antenna RCU Ethernet

RS485
OMC
CCU
RS232
Modem BTS-Control Fixed line
Modem BTS Fixed line
Ethernet
RCU OMC Ethernet

RS485
Communication between OMC and CCU via fixed line
In case of missing Ethernet and fixed telephone lines at the site a GSM-modem enables a wireless solution. Wireless
Antenna RCU OMC CCU-Control
RS232
CCU-Control
CCU
BTS-Control
BTS
Communication between OMC and CCU via Ethernet
Ethernet
RS485
CCU
RS232
Modem BTS-Control
Modem BTS
Communication between OMC and CCU via wireless units RET 155
System for Remote Electrical Tilt (RET) Browser Application

The CCU runs a webserver. RCUs and CCUs as part of a network can be configured and controlled through a standard browser, e.g. Netscape, Internet Explorer no additional software is required. You can control the RETsystem directly on site or via a long distance. The connection to each CCU is generated easily by typing in its individual IP-address. The appearing website contains all required control functions for normal service and installation. The CCU program allows in addition to the configuration and control of the connected RCUs, to also display the device status, command history list and various system errors. It is also possible to perform CCU software updates. The browser application is a helpful tool for the installation team on site, especially during initial configuration of a RET-system Each CCU and with it each of the connected RCUs can be addressed and controlled individually. Therefore, the browser application also offers a comfortable solution to respond on new situations by changing the individual downtilt angles fast and easily.
on rmati r info rthe For fu see the al ! manu ware soft

RET Screenshot of CCU browser application 156
Attachment of the RCU
Attachment of the RCU (Remote Control Unit) for remote-controlled downtilt adjustment:
Remove the protective cap completely from the antenna. Check the proper functioning of the phase-shifter over the entire adjustment range, by twisting the adjustment wheel in such a way that the spindle moves completely in and out. Reset the downtilt to the previous value.
Completely remove the black adjustement wheel by simply pulling it downwards.
Push the attachment nut of the RCU down towards the housing. Place the RCU carefully over the adjustment spindle, observing the correct alignment of the RCU with regards to the antenna, i.e. the flat surfaces of the attachment fixture on the antenna side and those inside the RCU housing must lie flat against each other. Push-up the RCU carefully to the stop at the antenna. Please note! Do not twist the RCU in any way during attaching to the antenna, as this could damage the adjustment spindle.
Tighten the RCU attachment nut using a torque-wrench; wrench width = 41 mm, min. torque = 15 Nm max. torque = 18 Nm. Connect the RCU control cable immediately after attachment of the RCU. Please note! In cases where a mechanical downtilt unit is installed, this must not be set for a downtilt of more than 14 degrees.
157
RET
General Instructions for Feederline Installation for F-Panels with four Connectors arranged on two Levels
Please note: In order not to damage the interfaces, please make sure that only the right tools are used. For fixing the nut of the connector we recommend using a common torque-wrench with a suitable wrench width.
Description of connector arrangement:
4 2
3 1
To make the installation of the feederlines and the connectors easier, the interfaces are arranged on two levels.
There are four interfaces for feeding the antenna located at the bottom.
Attachment of the feederline connector and the RCU:
Start with the rearside located interface no. 1. Place the connector carefully and fix the nut using a torque-wrench (according to the manufacturers guidelines). The further sequence for the installation is: feederlines no. 2, 3, 4.
After feederline installation the remote control units (RCU) can be attached.
For full description of RCU installation see datasheet Type no. 860 10003.
RET
Please note: Sealing of the correctly installed connectors cap nuts for additional weather protection is not required, nor is it recommended by the connector manufacturers.
158
General Instructions for Feederline Installation for A-Panels with four Connectors arranged on two Levels
Please note: In order not to damage the interfaces, please make sure that only the right tools are used. For fixing the nut of the connector we recommend using a common torque-wrench with a suitable wrench width.
Description of connector arrangement:
4 2
3 1
To make the installation of the feederlines and the connectors easier, the interfaces are arranged on two levels.
There are four interfaces for feeding the antenna located at the bottom.
Attachment of the feederline connector and RCU:
Start with the rearside located interface no. 1. Place the connector carefully and fix the nut using a torque-wrench (according to the manufacturers guidelines). The further sequence for the installation is: feederlines no. 2, 3, 4.
After feederline installation the remote control units (RCU) can be attached.
For full description of RCU installation see datasheet Type no. 860 10003.
Please note: Sealing of the correctly installed connectors cap nuts for additional weather protection is not required, nor is it recommended by the connector manufacturers.
159
RET
General Instructions for Feederline Installation for Triple-band Antennas with Kathrein Installation Tool, Type No. 850 10005
Note: To avoid any damage to the interfaces, please ensure that only suitable tools are used. To tighten the nuts of the feederline connectors, we strongly recommend using a special Kathrein installation tool (as shown below) in combination with a standard torque-wrench. Description of connector arrangement: Kathrein installation tool: Type No. 850 10005
1/2 square actuation according to DIN 3120 Form C 2 1 3 RET interfaces (13) 27 or 32 mm
Feederline connectors (49) 8 6 4 5 7 9 This tool is suitable for 7-16 connectors with a wrench size of 27 mm or 32 mm. Tighten nut within a torque range of 25 33 Nm depending on connector manufacturers specifications. The tool has to be ordered separately! Two tools per type no. (27 and 32 mm) were delivered in a common package.
There are six RF-Connections and three RET-interfaces located at the bottom of the antenna.
Attachment of the feederline connector and RCU:
The sequence for installation is: feederline no. 4, 5, 6, 7, 8, 9. Put the connector carefully in place and hand-screw the nut on. Use a torque-wrench to finish installation (see installation tool). Repeat operations as shown in figures A and B for each feederline!
Note: In order to protect the RET interface the protective caps have to be attached during feederline installation! Before RCU installation, it is absolutely essential to set the downtilt to 0 (either manually or by remote control).
After feederline installation, the remote control units (RCU) can be attached, The sequence for the installation of the RCUs is: RCU no. 1, 2, 3. For full description of RCU installation please refer to data sheet type no. 860 10003.
Not following these instructions may damage the downtilt spindle!
RET
Note: Sealing of the correctly installed connectors cap nuts for additional weather protection is not required, nor is it recommended by the connector manufacturers.
160
Remote Control Unit (RCU)
Remote Control Unit (RCU) for Kathrein base station antennas with adjustable electrical downtilt and appropriate mechanical interface.
Type No. Power supply Hardware interface Logical interface Adjustment time (full range) Adjustment cycles Temperature range Material of housing Weight Packing size Dimensions Scope of supply:
860 10003
10 30 V RS485 HEX coded commands based on HDLC protocol, conform to AISG typically 30 sec., depending on antenna type > 50000 40 C +60 C Aluminum approx. 1.1 kg 297 x 217 x 135 mm 85 x 130 x 150 mm (without connectors) RCU with suitable attachment interface for the antenna. The RCU can be easily attached without dismantling of the antenna. The RCU is suitable for operation under outdoor conditions. RCU in combination with antenna 742 212
Features:
Two RCUs in combination with antenna 742 234
Please note:
As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4, which includes the static mechanical load imposed on an antenna by wind at maximum velocity. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna/RCU or even cause it to fall to the ground.These facts must be considered during the site planning process. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. The details given in our data sheets have to be followed carefully when installing the antennas and accessories. The limits for the coupling torque of RF-connectors, recommended by the connector manufacturers must be obeyed. Any previous datasheet issues have now become invalid. RET
161
Central Control Unit (CCU) For Remote Electrical Tilt (RET/RCU) and Tower Mounted Amplifier (TMA) Control, Indoor Use
Central Control Unit

Type No. Connectors to RCU Power supply from BTS Power supply to RCU Power supply to RCU (via TMA) Interface to RCU and TMA Protocol Interface to BTS and protocol Alarm interface to BTS Modem support Max. number of RCUs and/or TMAs Max. length of control cable Temperature range Packing size Height/width/depth * HU = Height Unit
860 10006
DC: 48 V / max. 1.5 A AC: 110 V 240 V / max 0.7 A
860 10026
DC: 48 V / max. 1.5 A
3 x 8 pin connector according DIN 41 326, IEC 130, female, conform to AISG
3 x +29 V / max. 2 A / max. 50 W 3 x 13 V / max. 1.5 A / max. 50 W RS 485 / power supply HDLC hex-coded command set, conform to AISG Ethernet (10 base T) or RS 232 SNMP, HTTP, XML-RPC 8 x open collector output GSM, Siemens MC35 Terminal or TC35 Terminal 6 9 pcs., depending on cable configuration and max. power 100 m / 6 RCUs (depending on configuration) 25 C ... +55 C ambient temperature 597 x 367 x 148 mm 19" 1 HU* (43.6 / 483 / 250 mm)
Antenna
Antenna
Antenna
Antenna
Smart Smart Smart Smart
Bias Tee Bias Tee Bias Tee Bias Tee
782 782 782 782
10253 10255 10254 10255
(12 (24 (12 (24
V), BTS V), BTS V), Antenna V), Antenna
RCU
RCU
RCU
RCU RS 485
Smart Bias Tee
TMA Splitter 1:3

Type No. 860 860 860 860 860 860 860 860 860 860 860 860 860 860 860 10002 10003 10007 10008 10029 10009 10010 10032 10011 10012 10033 10013 10014 10015 10034 Description Splitter for RCU Remote Control Unit (RCU) RCU-Cable RCU-Cable RCU-Cable RCU-Cable RCU-Cable RCU-Cable RCU-Cable RCU-Cable RCU-Cable RCU-Cable RCU-Cable RCU-Cable Ethernet Cable Crossover Length
Smart Bias Tee
Smart Bias Tee
To Splitter or to RET/TMA via Smart Bias Tee 3 x RS 485 and 3 x +13 V / 3 x +29 V Central Control Unit AC Depending on Type No.
1 2 3 5 10 20 25 40 50 60 80 100 3
m m m m m m m m m m m m m
Interface Network
Alarm interface
RS 232
Ethernet 8 x Open Collector PC/Modem
DC: 48 V
AC: 110 V 240 V
RET
162
Antenna RCU
Power Supply and Signal Cable For Remote Control Unit (RCU) Indoor and Outdoor Use
Cable for RCU assembled with suitable connectors for Remote Control Unit / Splitter / Central Control Unit
Type No. Connectors
860 10007
2 x 8 pin connector according DIN 41 326, IEC 130, female/male Screen 1 x twisted pair 100 /1 MHz 2 x power supply, 1 x ground AWM style 20317 I/II A/B 4 A (power supply) (at 50 C air temperature) 40 C to +80 C, (fixed position) IP 67 (connected) 8 mm VL 1581 VW-1 CSA FT 1 one time 60 mm several times 120 mm
Construction
Rated current Temperature range Protection class Cable diameter Flammability
Minimum bending radius:
RCU-Cable
Type No. 860 860 860 860 860 860 860 860 860 860 860 860 10007 10008 10029 10009 10010 10032 10011 10012 10033 10013 10014 10015 Description RCU-Cable RCU-Cable RCU-Cable RCU-Cable RCU-Cable RCU-Cable RCU-Cable RCU-Cable RCU-Cable RCU-Cable RCU-Cable RCU-Cable Length 1 2 3 5 10 20 25 40 50 60 80 100 m m m m m m m m m m m m
163
RET
DC-Power and Signal Splitter For Remote Control Unit (RCU) Indoor and Outdoor Use
3-way-Splitter for RCU

Type No. Connectors
860 10002
4 x 8 pin connector according DIN 41 326, IEC 130-9 1 x male, 3 x female Screwing 3 A (at 50 C) 60 V IP 65 250 g 114 x 117 x 117 mm 91 / 103 / 72 mm Connector plate: Aluminum. Cap: Plastic. To masts, 50 145 mm diameter by clamp (supplied). Wall mounting by screws (not supplied). Connectors must be situated at the bottom. No inverted mounting possible.
Locking of connector Rated current (power supply) Max. voltage Protection class Weight Packing size Height/width/depth Material: Mounting:
Note:
2 pins (power supply, max. 3 A)
6 pins (max. 0.1 A)
Input
Output 1
Output 2
Output 3
RET
Clamp, Art. No. 1311847
164
Lightning Protection Device (LPD) For Remote Electrical Tilt (RET) Indoor and Outdoor Use
The device is designed for lightning protection of control cables carrying partial lightning currents up to 25 kA (shield) and 2,5 kA (inner conductor), according IEC 61643-1, IEC 61312-3. Each pin is protected individually. Lightning Protection Device for RET
Type No. Connectors
860 10030
2 x 8 pin connector according DIN 41 326, IEC 130-9, input: male, output: female 8 x bipolar gas tube 25 kA (housing, shield) (10/350 s) inner conductors: 2,5 kA/pin (10/350 s) < 700 V < 100 V Via mounting plate / clamps at metallic surfaces or via separate cable, min. cross-section 5 mm2 Cu (screw M6) 4 A at 50 C 60 V 250 g 114 x 117 x 117 mm 91 / 103 / 72 mm Connector plate: Aluminum. Cap: Plastic. To masts, 50 145 mm diameter by clamp (supplied). Wall mounting by screws M4 (not supplied). No decoupling elements are integrated. The coordination with additional LPDs (device input) should be checked according to IEC 61312. Grounding of the device via the mounting plate at metallic surfaces or via additional grounding cable (not included in the delivery extend). Connectors must be situated at the bottom. No inverted mounting possible. Important: A control cable with a minimum length of 2 meters is required between Lightning Protection Device and Central Control Unit at the BTS to achieve the required decoupling.
SPD-Type Max. impuls current Max. dynamic overvoltage at spark gap (1 kV/s) Static overvoltage (100 V/s) Grounding
Max. operation current Max. operation voltage Weight Packing size Height/width/depth Material: Mounting:
Note:
Clamp, Art. No. 1311847
165
RET
Earthing Clamp For Power Supply and Control Cable For Remote Control Unit (RCU)
The clamp is designed for lightning protection of control cables according to EN 50164-1
Earthing clamp for RCU power supply and signal cable

Type No. Max. lightning current Contact resistance Protection class Grounding
860 10031
100 kA (pulse 10/350 sec) < 1 m IP 68 Via stranded grounding wire, 16 mm2, length 1 m, with integrated cable eyes, hole diameter 8 mm Plastic bag: 210 x 210 mm 240 g Body: Stainless steel with vulcanized EthylenePropylene-Caoutchouc Screw: Stainless steel Skin: Copper alloy Grounding wire: Copper
Packing size Weight Material:
Please note:
The earthing clamp is suitable only for the Kathrein Power Supply and Signal Cables, Type No. 860 10007 to 860 10015, 860 10029, 860 10032 and 860 10033 or shielded cables with shield diameter 6.1 mm jacket diameter 7.8 mm 0.3 mm
RET 166
DTMA UMTS AISG

Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier)
Double unit for easy use with XPol antennas Kathrein Cold Redundancy (patent pending) amplifier design for improved system reliability By-pass mode to ensure cell operation in case of TMA failure Built-in lightning protection Compact size Suitable for antenna RET control according to AISG standard RET = Remote Electrical Tilt AISG = Antenna Interface Standards Group Technical Data
Type No.
782 10147
782 10148
782 10149
Ant 1
DTMA UMTS 12 AISG DTMA UMTS 24 AISG DTMA UMTS 32 AISG (12 dB gain) (24 dB gain) (32 dB gain)
Tx Characteristics Frequency range Bandwidth Insertion loss Ripple Input power Intermodulation products in Rx band Return loss Rx Characteristics Frequency range Bandwidth Loss in by-pass mode Gain ripple Return loss 2110 2170 MHz 60 MHz Typically 0.3 dB < 0.2 dB < 100 W (+50 dBm) CW < 1.6 kW (+62 dBm) Peak < 120 dBm (2 Tx carriers at +43 dBm) Typically 20 dB
Ant 0
1920 1980 MHz 60 MHz < 2.6 dB (DC OFF) < 0.3 dB Typically 20 dB 20 dB (DC ON) > 12 dB (DC OFF) 12 1.0 dB 12 0.5 dB Typically 1.5 dB > 15 dBm > 25 dBm 24 1.0 dB 24 0.5 dB Typically 1.5 dB > 20 dBm > 30 dBm 32 1.0 dB 32 0.5 dB Typically 1.8 dB > 27 dBm > 37 dBm
BTS 1 BTS 0
Gain 40 +65 C +22 +28 C Noise figure Output 1-dB compression point 3rd order intercept point (OIP3) Environmental Characteristics Operating temperature range IP rating MTBF EMC DC and Alarm Characteristics DC supply voltage Power consumption Alarm management Modem Characteristics Mechanical Characteristics Material Connectors RF RET DC Mounting Weight Packing size Dimensions (w x h x d)

Type No. 734 360 734 361 Clamp set suitable for mast diameter of 34 60 mm 60 80 mm 80 100 mm 100 120 mm 120 140 mm 45 125 mm
40 +65 C IP67 > 500 000 hours (Double TMA) ETS 300 343-3
734 362 734 363 734 364 734 365
+24 V nominal (minus grounded) Typically 1.5 W per TMA Typically 3 W per TMA Typically 8 W per TMA According to AISG standard According to AISG standard
+12 V nominal (minus grounded)
Aluminium housing 7-16 female 8-pin female, IEC 60130-9 (Pin 1: +12 V DC nominal, pin 3: RS485A, pin 5: RS485B, pin 7: DC return, pin 6: 24 V DC; other pins: Not connected) Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 5 kg 502 mm x 262 mm x 214 mm 172 mm x 262 mm x 84 mm (without connectors, without mounting brackets) 167 RET
Smart Bias Tee 800 2170 MHz
The Smart Bias Tee combines the performance of a standard Bias Tee (e. g. type 793 304) with the function of an additional modem (AISG standard) in order to provide either DC voltage as well as remote control signals via an RF feeder cable to a TMA or RCU. The Smart Bias Tee provides low RF signal insertion loss from port 1 to port 2 and vice versa.The measures taken to protect against static discharge and lightning ensure a high level of reliability and operational safety. 782 10253: 12 V version for use near the BTS, in order to feed-in DC voltage and RCU control signals into a feeder cable 782 10254: 12 V version for use near the antenna, in order to control an RCU (only required if no TMA is in use) 782 10255: 24 V version for use near the BTS, in order to feed-in DC voltage and RCU control signals into a feeder cable 782 10256: 24 V version for use near the antenna, in order to control an RCU (only required if no TMA is in use) Abbreviations: RCU = Remote Control Unit for remote electrical control of antenna tilt BTS = Base Transceiver Station TMA = Tower Mounted Amplifier AISG = Antenna Interface Standards Group Port 1 = Port for BTS/Antenna Port 2 = Port for feeder cable Port DC/RCU = Port for DC voltage and remote control unit signals
782 10253
Port 2 Port DC/RCU
Port 1
Block diagram 782 10254 782 10256
Block diagram 782 10253 782 10255
Antenna system (1 sector) without TMA
Antenna system (1 sector) with Kathrein TMA
Application Examples
Technical Data
Type No. Connectors Port 1 Port 2 Port DC/RCU
782 10253
12 V / BTS
782 10254
12 V / Antenna
782 10255
24 V / BTS
782 10256
24 V / Antenna
Frequency range Insertion loss Port 1 Port 2 Isolation for DC and RCU signals Port 1 Port 2 Port 1 Port DC/RCU Port 2 Port DC/RCU VSWR (all ports) Input power Port 1 or port 2 Port DC/RCU Intermodulation products Impedance Temperature range Modem carrier frequency Application Weight Dimensions (w x h x d)
7-16 male 7-16 female 8-pin male connector 8-pin female connector 8-pin male connector 8-pin female connector (IEC 60130-9) (IEC 60130-9) (IEC 60130-9) (IEC 60130-9) Pin 1: 12 VDC in Pin 1: 12 VDC out Pin 6: 24 VDC in Pin 6: 24 VDC out (Pin 3: RS485-A, pin 5: RS485-B. pin 7: ground, other pins: not connected) 800 2170 MHz < 0.1 dB (800 2170 MHz) > 70 dB > 70 dB 0 dB < 1.1 (800 2170 MHz) < 250 W (800 2170 MHz) < 250 W (800 2170 MHz) < 2.5 A / +8 +14 VDC < 2.5 A / +14 +30 VDC < 160 dBc (3rd order; with 2 x 20 W) 50 40 ... +60 C 2.176 MHz Indoor or outdoor (IP66) 0.65 kg 128 mm x 76 mm x 46 mm (including connectors)
RET
168
Summary Electrical Accessories
Splitters
Type Type No. Frequency range Remark Max. power Connector Page female N 7-16 N 7-16 N 7-16 N 7-16 N N N 170 170 171 171 171 171 171 171 172 172 172
2-way-Splitter 800/900 2-way-Splitter 800/900 2-way-Splitter 2-way-Splitter 3-way-Splitter 3-way-Splitter 4-way-Splitter 4-way-Splitter 8002200 8002200 8002200 8002200 8002200 8002200
K 63 20 62 1 K 63 20 62 7 737 737 737 737 737 737 303 304 305 306 307 308
790 960 MHz Indoor/Outdoor 500 W 790 960 MHz Indoor/Outdoor 1000 W 800 800 800 800 800 800 2200 2200 2200 2200 2200 2200 MHz MHz MHz MHz MHz MHz Indoor/Outdoor Indoor/Outdoor Indoor/Outdoor Indoor/Outdoor Indoor/Outdoor Indoor/Outdoor Indoor Indoor Indoor 200 700 200 700 200 700 W W W W W W
2-way-Splitter 8002500 3-way-Splitter 8002500 4-way-Splitter 8002500
860 10017 860 10018 860 10019
800 2500 MHz 800 2500 MHz 800 2500 MHz
100 W 100 W 100 W
Tappers
Type Type No. Frequency range 800 2500 MHz 800 2500 MHz 800 2500 MHz Remark Max. power 100 W 100 W 100 W 500 W 500 W 500 W Connector Page female N N N 7-16 7-16 7-16 173 173 173 174 174 174
2-way-Tapper 8002500 7.0/1.0 dB 2-way-Tapper 8002500 10.4/0.4 dB 2-way-Tapper 8002500 15.1/0.1 dB
860 10020 860 10021 860 10022
Indoor Indoor Indoor
2-way-Tapper 8002200 7.0/1.0 dB K 63 23 60 67 2-way-Tapper 8002200 10.4/0.4 dB K 63 23 61 07 2-way-Tapper 8002200 15.1/0.1 dB K 63 23 61 57
800 2200 MHz Indoor/Outdoor 800 2200 MHz Indoor/Outdoor 800 2200 MHz Indoor/Outdoor
Continuously adjustable ratio

2-way-Tapper 824960/17102170 K 63 23 60 01 824 960 MHz 5.015.0dB 1710 2170 MHz 2-way-Tapper 870960/17102500 5.015.0dB 860 10023 870 960 MHz 1710 2500 MHz Indoor 100 W N 175
Indoor
100 W
175
Filter products summary Combiners, Filters, Bias Tees Duplexers DTMA 3-dB Couplers
tion orma ed inf gue etail For d the catalo lters, i see MHz F 2500 Amplifiers s 790 ners, i cation Comb Communi obile for M
176 177 178 179
169
Electrical Accessories
Multi-band Low-loss Power Splitters
790 960
For indoor and outdoor use.
2-way-Splitter 790960
Type No. Frequency range For connecting ... antennas Insertion loss Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power Connector (female) Weight Packing size Max. size Material:
K 63 20 62 1 K 63 20 62 7
790 960 MHz 2 < 0.05 dB 50 < 1.1 < 150 dBc 500 W 1000 W (at 50 C ambient temperature) N approx. 1.3 kg 240 x 93 x 107 mm 210 / 80 / 80 mm Housing: Aluminum. Inner conductor: Brass. Bracket for wall mounting included in the scope of supply: For pipe mast mounting use clamps listed below (order separately). DC transmission between all terminations (suitable for remote power supply systems). Input K 63 20 62 7 7-16
Mounting:
DC capability:
Clamps (order separately)

Type No. 736 736 736 736 736 801 802 803 804 805 Description 1 1 1 1 1 clamp clamp clamp clamp clamp Mast: Mast: Mast: Mast: Mast: 34 60 80 100 120 Remarks 60 80 100 120 140 mm mm mm mm mm diameter diameter diameter diameter diameter 736 805
170
800 2200
For indoor and outdoor use. 2-way-Splitter 8002200 3-way-Splitter 8002200 4-way-Splitter 8002200
Type No. Frequency range For connecting ... antennas Insertion loss Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power (at 50 C ambient temperature) Connector (female) Weight Packing size Max. size Material: Housing: Aluminum. Inner conductor: Brass. Bracket for wall mounting included in the scope of supply. For pipe mast mounting use clamps listed below (order separately). DC transmission between all terminations (suitable for remote power supply systems). 200 W N 700 W 7-16 2
737 303 737 304 737 305 737 306 737 307 737 308
800 2200 MHz 3 < 0.05 dB 50 < 1.15 < 150 dBc 200 W N 700 W 7-16 200 W N 700 W 7-16 4
approx. 1.5 kg 310 x 93 x 107 mm 294 / 82 / 82 mm
Mounting:
DC capability:
Input

Type No. 736 736 736 736 736 801 802 803 804 805 Description 1 1 1 1 1 clamp clamp clamp clamp clamp Mast: Mast: Mast: Mast: Mast: 34 60 80 100 120 Remarks 60 80 100 120 140 mm mm mm mm mm diameter diameter diameter diameter diameter
737 308
736 805
171
Splitters
800 2500
For indoor use. 2-way-Splitter 8002500 3-way-Splitter 8002500 4-way-Splitter 8002500

Type No. Frequency range For connecting ... antennas Insertion loss Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power Connector Weight Profile cross-section Packing size Max. size Material: Housing: Aluminum. Inner conductor: Brass. DC transmission between all terminations (suitbale for remote power supply systems). < 1.25 2
860 10017 860 10018 860 10019

800 2500 MHz 3 < 0.05 dB 50 < 1.25 < 150 dBc 100 W (at 50 C ambient temperature) N female approx. 0.6 kg 25 x 25 mm 242 x 110 x 95 mm 204 / 63 / 41 mm < 1.3 4
DC capability:
Input 860 10019
Splitters 172
Multi-band Low-loss Power Tappers
800 2500
For indoor use. 2-way-Tapper 8002500 7.0 /1.0dB 2-way-Tapper 8002500 10.4/0.4dB 2-way-Tapper 8002500 15.1/0.1dB
Type No. Frequency range Tap Loss Input P1 Input P2 For connecting ... antennas Insertion loss Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power Connector Weight Profile cross-section Packing size Max. size Material: Housing: Aluminum. Inner conductor: Brass. DC transmission only between input and port P1. P2 is coupled capacitively. 1.0 dB 7.0 dB
P1
860 10020 860 10021 860 10022

800 2500 MHz 0.4 dB 10.4 dB 2 < 0.05 dB 50 < 1.5 < 150 dBc 100 W (at 50 C ambient temperature) N female approx. 0.5 kg 25 x 25 mm 267 x 95 x 111 mm 244 / 64 / 25 mm 0.1 dB 15.1 dB
P2
DC capability:
Input 860 10020
173
Tappers
Multi-band Low-loss Power Tappers
800 2200
For indoor and outdoor use. 2-way-Tapper 8002200 7.0 /1.0dB 2-way-Tapper 8002200 10.4/0.4dB 2-way-Tapper 8002200 15.1/0.1dB
Type No. Frequency range Tap Loss Input P1 Input P2 For connecting ... antennas Insertion loss Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power Connector Weight Packing size Max. size Material: Housing: Aluminum. Inner conductor: Brass. 1.0 dB 7.0 dB
P1
800 2200 MHz 0.4 dB 10.4 dB 2 < 0.05 dB 50 < 1.5 < 150 dBc 500 W (at 50 C ambient temperature) 7-16 female approx. 1.3 kg 310 x 93 x 112 mm 244 / 90 / 55 mm 0.1 dB 15.1 dB
K 63 23 60 67 K 63 23 61 07 K 63 23 61 57
P2
Input
DC capability: DC transmission only between input and port P1. P2 is coupled capacitively. Bracked for wall mounting included in the scope of supply. For pipe mast mounting use clamps listed below (order separately).
K 63 23 60 67
Mounting:

Type No. 736 736 736 736 736 801 802 803 804 805 Description 1 1 1 1 1 clamp clamp clamp clamp clamp Mast: Mast: Mast: Mast: Mast: 34 60 80 100 120 Remarks 60 80 100 120 140 mm mm mm mm mm diameter diameter diameter diameter diameter 736 805 Tappers 174
Multi-band Low-loss Power Tapper Continuously Adjustable

For indoor use.
824 960
1710 2500
5.0 15.0
5.0 15.0
K 63 23 60 01: 2-way-Tapper 824960/17102170 5.015.0dB 860 10023: 2-way-Tapper 870960/17102500 5.015.0dB

Type No. Frequency range Power ratio between outputs (P2 P1) For connecting ... antennas Insertion loss Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power Connector Weight Profile cross-section Packing size Max. size Material:
P1
K 63 23 60 01 860 10023
824 960 MHz and 1710 2170 MHz 870 960 MHz and 1710 2500 MHz 5.0 dB to 15.0 dB continuously adjustable 2 < 0.1 dB 50 < 1.7 < 150 dBc 100 W (at 50 C ambient temperature) N female 0.5 kg 25 x 25 mm 249 x 111 x 40 mm 235 / 100 / 25 mm 277 x 111 x 40 mm 263 / 100 / 25 mm Blocking unit
P2
Housing: Aluminum. Inner conductor: Brass. Adjustment mechanism: ASA. DC transmission only between input and port P1. P2 is coupled capacitively.
DC capability:
Input 860 10023
Splitting table
P2 / P1 [dB] 5 6 7 8 9 10 11 12 13 14 15 Splitting ratio P1 / P2 3.2 4 5 6.3 8 10 12.6 15.8 20 25.1 31.6 Splitting attenuation PInput P1 [dB] PInput P2 [dB] 1.2 1.0 0.8 0.6 0.5 0.4 0.3 0.3 0.2 0.2 0.1 6.2 7.0 7.8 8.6 9.5 10.4 11.3 12.3 13.2 14.2 15.1
175
Tappers
Combiners, Filters, Bias Tees 50 2500 MHz
Dual-band Combiner
793 532 793 533 Single Unit Double Unit 806 960 / 1710 2170 MHz 806 960 / 1710 2170 MHz
793 532 Single Unit 793 533 Double Unit
782 10250 Single Unit, built-in DC stop 782 10251 Double Unit, built-in DC stop
806 960 / 1710 2170 MHz 806 960 / 1710 2170 MHz
782 10250 Single Unit 782 10251 Double Unit
793 423 793 424
Single Unit Single Unit
1710 1880 / 1920 2170 MHz 1710 1880 / 1920 2170 MHz
782 10243 Single Unit, built-in DC stop 1710 1880 / 1920 2170 MHz 782 10244 Double Unit, built-in DC stop 1710 1880 / 1920 2170 MHz
782 10264 Single Unit
50 2200 / 2400 2500 MHz
793 423, 782 10243 Single Unit
793 424, 782 10244 Double Unit
Triple-band Combiner
793 425 793 426 782 10245 782 10246 Single Unit Double Unit 880 960 / 1710 1880 / 1920 2170 MHz 880 960 / 1710 1880 / 1920 2170 MHz
Single Unit 880 960 / 1710 1880 / 1920 2170 MHz built-in DC stop Double Unit 880 960 / 1710 1880 / 1920 2170 MHz built-in DC stop
793 425, 782 10245 Single Unit 793 426, 782 10246 Double Unit
793 528 793 529
Single Unit Double Unit
806 960 / 1710 1880 / 1920 2170 MHz 806 960 / 1710 1880 / 1920 2170 MHz
Smart Bias Tee

782 782 782 782 10253 10254 10255 10256 12 12 24 24 V BTS V Antenna V BTS V Antenna 800 800 800 800 2170 2170 2170 2170 MHz MHz MHz MHz
793 528 Single Unit
793 529 Double Unit
Bias Tee
793 304 800 2170 MHz
DC Stop
793 301 800 2170 MHz
Band-pass Filter
Filter products
793 540
1710 1880 MHz
Low-pass Filter
793 539 876 960 MHz
176
For more information please contact: filteramp@kathrein.de
Duplexers 824 2170 MHz
Duplexer GSM-R / GSM

793 004 793 005 7-16 N 876 880 / 921 925 MHz 876 880 / 921 925 MHz
793 004 793 005
782 782 782 782
10164 10165 10161 10162
7-16 1 x N, 3 x 7-16 7-16, 19" drawer 7-16, outdoor
890 890 890 890
915 915 915 915
/ / / /
935 935 935 935
960 960 960 960
MHz MHz MHz MHz
782 10164 (indoor)
782 10162 (outdoor)
782 10161 (19 drawer)
782 10167
7-16
880 915 / 925 960 MHz
Duplexer AMPS A-Band, B-Band A/B-Band

782 10168 782 10169 7-16 7-16, outdoor 824 835 / 869 880 MHz 824 835 / 869 880 MHz
782 10168, 782 10171 (indoor)
782 10171 782 10172
7-16 7-16, outdoor
835 851 / 880 896 MHz 835 851 / 880 896 MHz
782 10215 782 10216
7-16 N
824 851 / 869 896 MHz 824 851 / 869 896 MHz
782 10169, 782 10172 (outdoor)
782 10257 782 10265
7-16, 400 W 7-16, 800 W
824 846.5 / 869 891.5 MHz 824 846.5 / 869 891.5 MHz
782 10215, 782 10257 782 10216
Duplexer GSM 1800 / GSM 1900

792 542 792 544 7-16 7-16 1710 1785 / 1805 1880 MHz 1850 1910 / 1930 1990 MHz
Duplexer UMTS
782 10192 7-16 1920 1980 / 2110 2170 MHz
177
Filter products
DTMAs 1920 2170 MHz
UMTS Double Tower Mounted Amplifier

782 10071 782 10072 12 dB gain 24 dB gain UL: 1920 1980 / DL: 2110 2170 MHz UL: 1920 1980 / DL: 2110 2170 MHz
UMTS Double Tower Mounted Amplifier AISG Standard

782 10147 782 10148 782 10149 12 dB gain 24 dB gain 32 dB gain UL: 1920 1980 / DL: 2110 2170 MHz UL: 1920 1980 / DL: 2110 2170 MHz UL: 1920 1980 / DL: 2110 2170 MHz
Filter products 178
3-dB Couplers 800 2500 MHz
3-dB Coupler
793 506 793 006 793 554 7-16, outdoor 7-16, outdoor 7-16, outdoor 806 960 MHz 1700 2200 MHz 800 2200 MHz
3-dB Coupler with Cable Absorber

792 699 792 702 793 555 806 960 MHz 1700 2200 MHz 800 2200 MHz
Antenna Tx1
Tx2
Measuring Directional Coupler

792 972 824 2500 MHz
179
Filter products
180
Summary Mechanical Accessories Clamps, Downtilt Kits ...
Page
Mounting Configurations A-Panels / C-Panels / Eurocell Panels

Dimensions Clamps Three Sector Clamps and Masts 2 x A-Panel Mounting Kit Downtilt kits
182
183 185 187 188 189
F-Panels
Dimensions Detailed Connector Position Clamps Three Sector Clamp 2 x F-Panel Mounting Kit Downtilt kits Slant Compensation 192 193 194 195 196 197 197
Omnidirectional Antennas
Clamp for larger Mast Diameters Side-mounting Brackets 198 199
Tools
Azimuth Adjustment Tool Kathrein Installation Tool (Triple-band Antenna) 201 160
For additional information on the mounting of antennas, please check also our broschure:
181
Mechanical Accessories
Mounting Configurations
Small Pipe Diameter
Large Pipe Diameter
Off-set
Flat Surface
Not applicable for Eurocell Panels with connector position rearside.
Standard Downtilt
Off-set Downtilt
182
A-Panels Antenna Dimensions

72
A-Panels with 65 and 90 Half-power Beam Width

A B C 256 mm 310 mm 350 mm 656 mm 1296 mm 1936 mm 2580 mm 710 mm 1350 mm 1990 mm 2634 mm 750 mm 1390 mm 2030 mm 2674 mm
64 9
A Corresponds with the antenna height mentioned in the technical data.
Bottom view 58
-45
+45
262
72 64 9
Dual-band A-Panels with 65 Half-power Beam Width

A B C 770 mm 824 mm 864 mm 1316 mm 1367 mm 1407 mm 1916 mm 1967 mm 2007 mm 2516 mm 2567 mm 2607 mm
116 A B
Adjustment mechanism with integrated scale 58
139
52
262 Bottom view
183
A-Panels ...
A-Panels / C-Panels / Eurocell Panels Antenna Dimensions

72
Triple-band A-Panel with 65 Half-power Beam Width

A B C 1498 mm 2058 mm 2628 mm 1541 mm 2101 mm 2671 mm 1581 mm 2141 mm 2711 mm
64 9
Adjustment mechanism with integrated scale
262 Bottom view
72 64 9
C-Panels
A B C 1294 mm 1934 mm 2254 mm 1340 mm 1980 mm 2300 mm 1382 mm 2022 mm 2342 mm
Eurocell Panels
A B C 264 mm 654 mm 974 mm 1294 mm 1934 mm 2254 mm 2574 mm 710 mm 1030 mm 1350 mm 1990 mm 2310 mm 2630 mm 750 mm 1070 mm 1390 mm 2030 mm 2350 mm 2670 mm
A B C
Top view
A-Panels ...
258
184
103
149
A-Panels 30 Half-power Beam Width Mounting Hardware

A-Panels with 30 Half-power Beam Width
A B 656 mm 1296 mm 2580 mm 584 mm 1224 mm 2504 mm
11
B Side view 177 Downtilt kit 733 695 A-Panels ...
180.5 348 560 Bottom view
Clamps
Type No. 733 736 K 61 14 03 K 61 14 04 K 61 14 05 Description 2 2 2 2 clamps clamps clamps clamps Mast: Mast: Mast: Mast: Remarks 50 125 mm diameter 116 210 mm diameter 210 380 mm diameter 380 521 mm diameter Weight Units per approx. antenna 5.9 4.6 6.5 9.4 kg kg kg kg 1 1 1 1
Pair of clamps K 61 14 03
Downtilt kits
Antenna height 656 mm 1296 mm 2580 mm Downtilt angle 0 33 0 16 0 8 Type No. Weight
733 695
3.4 kg
116
185
A-Panels 65 and 90 / C-Panels / Eurocell Panels Mounting Hardware Clamps

C-Panels / Eurocell Panels C-Panels / Eurocell Panels C-Panels / Eurocell Panels Antenna height: 2574 mm Antenna height: 654 mm Antenna height: 264 mm to 2254 mm and all A-Panels 65 and 90
10 25 8 8 3 10 25 3 25 8 10 3
26
25
74
65 9 4 1274 1994 2234 54
Description Small Pipe
Mast diameter 28 64 mm 50 115 mm 110 220 mm 210 380 mm 60 115 mm 115 210 mm 210 380 mm 380 521 mm
Type No. *731 651* 738 546 850 10002 850 10003 733 733 733 733 677 678 679 680
Distance A mm 22 30 18 26 47 56 48 69 117 124 146 160 148 168 150 175
Weight Units per approx. antenna 330 g 1.0 kg 2.7 kg 4.8 kg 2.0 2.6 4.0 5.3 kg kg kg kg see sketch see sketch see sketch see sketch see see see see sketch sketch sketch sketch
Large Pipe new new Off-set
* Not allowed for panels 742 241, 742 264, 742 265, 742 266
731 651
738 546
733 678
50 mm 26 mm A-Panels ... 40 mm
186
A-Panels / C-Panels / Eurocell Panels 3 Sector Panel Arrangement Mounting Hardware 3 Sector Clamp Kit / Pipe Mast with Flange Base
Slim and unobstrusive design Nearly cylindrical optical appearance with small outer diameter q Suitable for all A-Panels 65 and 90 (Single-band, Dual-band) with weight less than 30 kg including downtilt kit q Mounting of F-Panels possible but not optimized
q q
3 Sector Clamp Kit

Type No. Angle between antennas Suitable for mast diameter Type No. of pipe mast (please order separately) Number of pieces 742 033 120 114.3 mm 742 035 742 034 120 139.7 mm 742 036
2 x 3 sector clamp 2 x 3 sector clamp 2 x mounting support 2 x mounting support clamp clamp Material 3 sector clamp Hot-dip galvanized steel Hot-dip galvanized steel Mounting support Aluminum Aluminum clamp Screws Stainless steel Stainless steel Outer diameter (Dout) of the 3 A-Panel Arrangement 460 mm 482 mm Weight Clamp kit 3.0 kg 3.2 kg 3 sector clamp 1.4 kg 1.5 kg 64 0.5 Dout 9 3 sector clamp
60
Mounting support clamp D Torque 8 Nm
Bottom view without downtilt kit
Type No. A B 742 033 114.3 88 742 034 139.7 100 all dimensions in mm
C 217 236
D 207 228
E 49 49
F 45 45
Pipe Mast with Flange Base

Type No. Pipe diameter D according DIN 2448 Wall thickness pipe Pipe length Flange diameter Flange thickness S Hole circle diameter Number of holes Hole diameter Enclosed bolts thread x length Hot-dip galvanized steel Weight Material pipe mast Material flange base 742 035 114.3 mm 742 036
6.3 mm 4 mm 3000 mm 3000 mm 210 mm 265 mm 14 1 mm 19 1 mm 170 mm 225 mm 6 6 18 1 mm 18 1 mm M16 x 100 mm M16 x 100 mm Quality min. 8.8 Quality min. 8.8 60 kg 55 kg S355 J2H (St 52-3N) DIN EN 10210-1 S235 JR G2 (RSt 37-2) DIN EN 10025
181
170 210 742 035
225 265 742 036 A-Panels ...
Maximum permissible load: According DIN 4131 and DIN 4132 Fatigue class K2
129 2
139.7 mm S
3000
187
A-Panels / C-Panels / Eurocell Panels Mounting Hardware 2 x A-/C-Panel Mounting Kit

Use this mounting kit only for antennas less than 25 kg each.
Type No. No. of pieces Suitable for A-/C-Panels 65, 90 with a max. height Material: Clamp Screws Weight Mounting
850 10006
2 x brackets 2.6 m Hot-dip galvanized steel Stainless steel Approx. 3.3 kg Screws are supplied
Recommended torque for M8 bolted connections: 12 Nm 3901 640.2
34
640.2
640.2
R1
73
0.5
2800.5
Mounting Accessories (order separately) Clamps (only the listed clamps are allowed!)
Type No. 850 10002 850 10003 Description 1 clamp 1 clamp Remarks Mast: 110 220 mm diameter Weight Units per approx. antenna 2.7 kg 2 2
Mast: 210 380 mm diameter 4.8 kg
Please chose the fitting downtilt kit that you need, from the antenna datasheet.
A-Panels ...
188
A-Panels / C-Panels / Eurocell Panels Mounting Hardware Downtilt kit

Antenna height: 654 974 1294 1934 2254 / 656 mm mm / 1296 mm / 1936 mm / 2256 mm
Use the downtilt kit together with the clamps (see page 185 and 186)
Screws supplied
Scale
Downtilt angle
Antenna height 654 / 656 mm 974 mm 1294 / 1296 mm 1934 / 1936 mm 2254 / 2256 mm Downtilt angle 0 30 0 21 0 16 0 11 0 9
Downtilt kit with scale Type No. 737 972 737 973 737 974 737 975
Mounting a downtilt kit enlarges the spacing between mast and antenna by 84 mm.
189
A-Panels ...
* Instructions to adjust the required downtilt angle are given in the datasheet or on the rearside of the antenna.
12 69
15
wed ot allo are n t more kits weigh wntilt 70, he do els with a 266, 742 2 T n 2 for Pa g, like: 74 , 742 241 191 272 25 k 42 page than 271, 7 ibility see 742 oss ntilt p r dow fo
Downtilt kit without scale* Type No. Weight
737 978
approx. 2.8 kg
A-Panels / C-Panels / Eurocell Panels Mounting Hardware Downtilt kits

Suitable for: A-Panels with an antenna height of 2580 mm C-Panels / Eurocell Panels with an antenna height of 2574 mm
Screws supplied Screws supplied
Scale
Scale
Type No. 737 971 Downtilt angle: 0 8
ed allow is not t more lt kit weigh ownti 70, The d els with a 266, 742 2 n 2 for Pa g, like: 74 , 742 241 191 272 25 k 42 page than 271, 7 ibility see 742 oss ntilt p r dow fo
Type No. 737 976 Downtilt angle: 0 8
The downtilt kits should only be mounted with clamps 738 546, 850 10002, 850 10003
A-Panels ...
190
12 69
15
12 69
15
A-Panels / C-Panels / Eurocell Panels Mounting Hardware Downtilt Kit

Special downtilt kit for Panel antennas with a weight greater than 25 kg.
Downtilt kit
Type No. Preferred range of use M10 supplied M8 supplied
850 10007
Panel antennas with a weight of 25 kg Panel antennas with attached mounting plates Downtilt kit without scale for universal use 5.9 kg Hot-dip galvanized steel Stainless steel
Weight Material All screws and nuts
Recommended mast clamps:

Type No. 738 546 850 10002 850 10003 Description 1 clamp 1 clamp 1 clamp Mast diameter 50 115 mm 110 220 mm 210 380 mm Weight approx. 1.0 kg 2.7 kg 4.8 kg Units per antenna 2 2 2
Recommended torque for all bolted connections:

Screw size M8 M10 Torque 12 Nm 26 Nm
Maximum acceptable load:

Frontal wind load Lateral wind load Antenna weight < 2500 N < 830 N 50 kg 640.5 90
9
Antenna height 1498 mm 2058 mm 2516 mm 2628 mm
Downtilt angle 0 15 0 11 0 8 0 8 300 72

9
72 640.5 232
Downtilt angle
M10 A-Panels ...
191
F-Panel Accessories Dimensions of F-Panels with 33 105 Half-power Beam Width

Dimensions [mm] (A corresponds to the antenna height given on the data sheet)
33 Half-power Beam Width

A 209 342 662 982 1302 1942 B 263 396 716 1036 1356 1996 C 303 436 756 1076 1396 2036
60 105 Half-power Beam Width

A 182 342 502 662 702 982 1302 1622 B 236 396 556 716 756 1036 1356 1676 1996 2636 C 266 426 586 746 786 1066 1386 1706 2026 2666
Front view
1942 2582
Front view
A B C
A B C
64 72 8.5 35
F-Panels
64 192
F-Panel Accessories Dimensions of F-Panels Detailed Connector Position

60 65 Half-power Beam Width
155

155 76

262 52
+45/45 Polarization

155 58

155 54
65 and 90 Half-power Beam Width adjustable electrical downtilt

45 +45
155
199 45
45 Half-power Beam Width Multi-band adjustable electrical downtilt
30 Half-power Beam Width Multi-band adjustable electrical downtilt

299 45
65 Half-power Beam Width 2-Multi-band adjustable electrical downtilt

299 48
65 Half-power Beam Width 2-Multi-band adjustable electrical downtilt

323 193 F-Panels
F-Panel Accessories Clamps for F-Panels

Clamps suitable for all F-Panels
Type No. Mast diameter 50 115 mm 110 220 mm 210 380 mm Weight approx. 1 kg 2.7 kg 4.8 kg Units per antenna For more information see data sheets 738 546 850 10002 850 10003 2 2 2
Type No. 738 546
40 mm
Clamps suitable for all F-Panels with a width of 155 mm until an antenna height of 1302 mm
Type No.
Mast diameter mm mm mm mm mm mm 182 182 182 182 182 182
Antenna height 1942 1942 1942 1942 1942 1942 mm mm mm mm mm mm
Units per approx. antenna 60 g 70 g 80 g 90 g 110 g 80 g 1 1 1 1 1 1 2 2 2 For more information see data sheets
Weight
734 734 734 734 734 734
360 34 60 361 60 80 362 80 100 363 100 120 364 120 140 365 45 125
738 546 50 115 mm 182 ... 2582 mm 1 kg 850 10002 110 220 mm 182 ... 2582 mm 2.7 kg 850 10003 210 380 mm 182 ... 2582 mm 4.8 kg
Clamps are not allowed for 2-Multi-band F-Panels like 742 233, 742 234, 742 235
Type No. 734 362
F-Panels
194
F-Panels 3 Sector Panel Arrangement Mounting Hardware 3 Sector Clamp Kit

Slim and unobstrusive design Nearly cylindrical optical appearance with small outer diameter q Suitable for all F-Panels with an antenna housing width of 155 mm
q q
3 Sector Clamp Kit

Type No. Angle between antennas Suitable for mast diameter Number of pieces 742 263 120 88.9 mm 2 x 3 sector clamp 2 x mounting support clamp Hot-dip galvanized steel Aluminum Stainless steel 315 mm 3.0 kg 1.4 kg This clamp kit is not suitable for use with additional mechanical downtilt kits
Material 3 sector clamp Mounting support clamp Screws Outer diameter (Dout) of the 3 F-Panel Arrangement Weight Clamp kit 3 sector clamp Remark
64 0.5
8.2
60
168 2
Torque 8 Nm
180 2
88
.9
65
Dout
4 5
+4 5
3 sector clamp 50
5
+4 5
42
Mounting support clamp
Bottom view
195
F-Panels
45
+45
F-Panel Accessories Mounting Hardware 2 x F-Panel Mounting Kit

For arranging two F-Panels 65, 90 side by side (on air combining). q The mounting kit consists of two mounting plates.
q
2 x F-Panel Mounting Kit

Type No. No of units Suitable for F-Panels 65, 90 with max. height of Material Weight Mounting 742 113 2 2m Hot-dip galvanized steel approx. 1.6 kg Screws are supplied
270
45
101
15 15
10
640.5
9 116
03
20 10
12 18
9 19
41
640.5
Configuration without mechanical downtilt
Configuration with mechanical downtilt
75
m 10 m
Use the 2 x F-Panel Mounting Kit together with the following mounting accessories
Type No. Description 738 733 733 733 733 737 546 677 678 679 680 978 1 1 1 1 1 1 clamp offset clamp offset clamp offset clamp offset clamp downtilt kit Remarks Mast: 50 115 mm diameter Mast: 60 115 mm diameter Mast: 115 210 mm diameter Mast: 210 380 mm diameter Mast: 380 521 mm diameter Downtilt angle: depending on antenna height Weight Units per approx. antenna 1.0 2.0 2.6 4.0 5.3 2.8 kg kg kg kg kg kg 2 2 2 2 2 1
For a three sector panel arrangement, use the mounting kit type no. 742 113 together with the three sector clamp (see page 195).
F-Panels
196
6
9 12
15
F-Panel Accessories Downtilt Kits and Slant Compensation Kit for F-Panels
Downtilt Kits with Type No. 737 ... are suitable for all F-Panels Use the downtilt kit together with the clamps (see page 194).
Downtilt kit with scale
0
Screws supplied
Downtilt kit without scale* Type No. Weight
Antenna height 342 mm 662 mm 982 mm 1302 mm 1622 mm 1942 mm 2582 mm
Downtilt angle 0 54 0 30 0 21 0 16 0 13 0 11 0 8
Type No. 737 972 737 973 737 974 737 975 737 971
Scale
Downtilt Kits with Type No. 732 ... are suitable for F-Panels until 1302 mm
Screws supplied
86 10 4 2
Scale Antenna height 342 502 662 982 1302 mm mm mm mm mm Downtilt angle 0 0 0 0 0 40 25 20 14 10
Slant Compensation Kit Type No. 732 319 for F-Panels with 60 160 Half-power Beam Width
57 mm
197
F-Panels
3
12 69
15
737 978
approx. 2.8 kg
Use the downtilt kit together with the clamps (see page 194).
Downtilt kit with scale Type No. 732 322 732 321 732 318 732 317 Downtilt kit without scale* Type No. Weight
732 327
approx. 1.0 kg
77 mm
Use the slant compensation kit type no. 732 319 together with the clamps (see page 194).
Weight: appr. 200 g
Side-mounting Clamp Omnidirectional Antennas Large Pipe

Type No. 738 908
For mast diameters of 94 125 mm
Antenna
Mast
b a
Omni
198
Side-mounting Bracket Omnidirectional Antennas

Type No. 737 398
Side-mounting bracket (for mast diameters of 40 105 mm)
Type No. Bracket 737 398 At the top and at the bottom 900 MHz 736 347 736 348 736 349 736 350 736 351 738 664 1800 MHz 739 785 738 187 739 404 737 190 A D
Fits for antenna type no:
Side-mounting is possible for four fixed distances between the tubular mast and the antenna:
900 MHz
A = 100 mm = 0.3
A
(holes 1 and 3)
1800 MHz
A = 240 mm = 0.75
A
(hole 2)
A = 160 mm = 0.5
A
A = 80 mm = 0.5 A Bracket
Antenna
Antenna base Mast
Bracket
Hole 3 D D Hole 1 D Hole 3
Hole 2 D
Pipe D
Horizontal Radiation Pattern
Spacing A Curve 100 mm
Pipe D
Pipe D Curve
Spacing A
40 mm 40 mm
dB
160 mm
3 0
100 mm
dB
160 mm
3 0 3
80 mm 100 mm
dB
direction from mast to antenna
240 mm
240 mm
199
Omni
Side-mounting Brackets Omnidirectional Antennas 900

For mast diameters of 40 105 mm
Type No. Bracket
K 61 33 5 at the bottom only
K 61 33 6 at both the top and the bottom D
Fits for antenna type no.
K 75 11 6 .. K 75 15 6 ..
738 779 741 558
Side mounting is possible for three fixed distances between the tubular mast and the antenna: 100 mm = 0.3 160 mm = 0.5 240 mm = 0.75
Pipe D
Additional gain to the nominal value of the antenna gain A 2 dB
160 mm 40 mm 3 dB
dB
240 mm
0
2 dB
direction from mast to antenna 100 mm 2.5 dB
160 mm 100 mm 3.5 dB
dB
240 mm
0
2.5 dB
K 61 33 6
Omni
200
A-Panel / C-Panel / F-Panel / Eurocell Panel Accessories Azimuth Adjustment Tool

Type No. 738 440
Precise azimuth adjustment for mast mounted antennas can easily be achieved by using the azimuth adjustment tool. This tool is suitable to all types of Eurocell Panels Panels A-Panels C-Panels F-Panels X-Pol F-Panels
Target object Scale
Target object
Elevation compensation
Move the stopper to central position*
Panel
Clamping device A-Panel
262
F-Panel 33
equivalent for
A-Panel
F-Panel
199
F-Panel F-Panel
155 equivalent for
F-Panel
X-Pol-F-Panel
F-Panel
X-Pol-F-Panel
Instruction: Use a map to work out the angle between the designed antenna azimuth and target (church, building, mountain peak). Set this angle on the scale of the adjustment tool. Place the adjustment tool onto the antenna and tighten the clamping device. Use the telescope to aim at the target object, if necessary, use elevation compensation. Then rotate the antenna until the target object appears in the telescope. * Observe the position of the stopper when fitting the azimuth adjustment tool.
201
Tools
Please contact for:

Sales queries, orders, catalogues or CD-ROM:
Fax: +49 80 31 1 84-8 20 E-Mail: central.sales@kathrein.de
Technical Information:
Fax: +49 80 31 1 84-9 73 E-Mail: antennas.mobilcom@kathrein.de
Internet: www.kathrein.de KATHREIN-Werke KG . Telephone +49 80 31 1 84-0 . Fax +49 80 31 1 84-9 91 Anton-Kathrein-Strae 1 3 . PO Box 10 04 44 . D-83004 Rosenheim . Germany
9987.147/0204/10/ZW/HA
Subject to alteration.

Kathrein Antenna

Uploaded by

Copyright:

Available Formats

Kathrein Antenna

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Kathrein Antenna

Uploaded by

Copyright:

Available Formats

Photo on title page: Selection of products for UMTS networks.

Quality leads the way

GSM 900 GSM-R GSM 850 CDMA 800

XPol GSM 1800 GSM 1900 PCS

Remote Electrical Tilt-System

Splitters / Tappers Filter Products

Clamps, Downtilt Kits, ...

List of available Catalogues for Mobile Communication Antennas and Accessories

790 2500 MHz Base Station Antennas for Mobile Communications

27 512 MHz Base Station Antennas for Mobile Communiations

Ground-to-Air Communication Antennas

Antennas for Trains and Busses

790 2500 MHz Filters, Combiners, Amplifiers for Mobile Communications

450 MHz Filters, Combiners, Amplifiers for Mobile Communications

80 / 160 MHz Filters, Combiners Amplifiers for Mobile Communications

The listed catalogues are also available on CD-ROM

74 75 194 194 194 194 194 194

45 190 189 189 189 189 190 189

737 307 737 308 737 398

62 65 67 68 69 116 143 142 21 52 14 15 120 137 89 131 91 92 93 94 95

132 143 14 130 144 144 34 35 36 37 85 78

860 10030 860 10031

Antenna Designs: Antenna Families Harmony of Design and Technology

Antenna Designs: Antenna Families Distinguishing features

Large variety of half-power beam width, gain values, electrical downtilt

Excellent grounding Multi-functional installation hardware

Directional Antenna Designs: Special Directional Antennas For Particular Applications

Downtilting of Antennas: Downtilt Possibilities

Mechanical downtilt Electrical downtilt

Manual adjustment procedure: (General example)

Remove protective cap.

Set downtilt angle by rotating the adjustment wheel.

Screw on the protective cap again.

Kathrein Antennas Product Description (Type)

XXPol A-Panel 870960/17101880 C 65/ 60 17/18dBi 28T/2T

Polarization(s): (X) Dual +45/ 45 (V) Vertical

Horizontal Half-power Beam Width(s)

Variable / Fixed Electrical Tilt(s)

XPol A-Panel XPol A-Panel XPol A-Panel

870960 806960 870960

15.5dBi 18.5dBi 21dBi

741 717 800 10141 741 785

739 650 739 662 739 666

Compact Panel (C-Panel)

GSM 900 XPol

A-Panel Dual Polarization Half-power Beam Width

Horizontal: Vertical: > 30 dB > 30 dB 50 < 1.5

< 150 dBc

500 W (at 50 C ambient temperature) 2 x 7-16 female Bottom

XPol A-Panel 806960 30 18.5dBi

A-Panel Dual Polarization Half-power Beam Width

Horizontal: Vertical: > 30 dB > 30 dB 50 < 1.5

A-Panel Dual Polarization Half-power Beam Width

XPol A-Panel 806960 65 12.5dBi

A-Panel Dual Polarization Half-power Beam Width

XPol A-Panel 806960 65 15dBi 6T

Vertical Pattern 6 electrical downtilt

A-Panel Dual Polarization Half-power Beam Width

Vertical Pattern 12 electrical downtilt

A-Panel Dual Polarization Half-power Beam Width Adjust. Electr. Downtilt