Pulsar DTSi Service Manual

Identification Data Salient Features
Performance :
Refined engine power delivery by optimization of Exhaus TEC

location and revised ignition timing with intelligent CDI
New clutch
provide better torque
& revamped gear shifting mechanism that gives smooth, positive, virtually friction-free gear shift feel
The Engine and Frame serial numbers are used to register the vehicles. They are the only means of identifying your particular vehicle from the other of the same model and type. These serial numbers may be needed by your dealer when ordering the parts. In the event of theft, the investigating authorities will require both these numbers in addition to the model, type and any special features of your vehicle that can help identifications.
New Bigger twin foam filter with an optimized intake system to Optimized valve timing and Roller rocker with NR bearing for
friction reduction that improves drivability.
Location of Parts
maintenance
LED tail lamp that consumes negligible power & require zero Stainless steel silencer that overcomes rusting problem All sensor type electrical switches that enables switches to
function for the life of the bike. Absolutely no maintenance in absence of mechanical contacts.
Style :
Stylish fairing and head lamp assembly with owleye A new black mask that separates headlamp from parking lights
adds to aesthetics.
Clear lens indicator with amber bulbs. New age, sharp and attractive 2 Row Tail lamp with LED lights New seat cowl to match stylish LED tail lamp. Louver type LH & RH covers with wire mesh gives sturdy look. Ergonomically designed self-letting switches
Convenience and Comfort
LCD Speedo Console with digital fuel gauge (12 level indicator) Digital speed display, odometer and two trip meter with resetting
provision.
Self-canceling indicators After completion of turn, the indicator

will be switched off automatically.
1. Control Switch RH
5. Hall Sensor for Indicator
Engine oil level window for easy to monitor level. Maintenance free battery once a year electrolyte top up. In addition to Fuel gauge, Reserve indicator bulb is provided that
glows continuously till the petrol filled to main level.
2. LCD Speedo Console
6. Vehicle Speed Sensor
3. Control Switch LH
7. ExhausTEC
Self check provision for Tachometer for its functioning
4. Body Control Unit
8. Tail Light LED display
(Placed inside Head Light fairing)
Pulsar DTS-i UG-III-180cc Training Notes
Dealer Development Center
Salient Features
Engine and Transmission
Type No. of cylinders Bore Stroke Engine displacement Compression ratio Idling Speed Max. net power Max. net torque Ignition System Ignition Timing : Fuel Carburettor Spark Plug Spark Plug Gap Lubrication Starting Clutch Transmission Primary Reduction Gear Ratios: 1st 2nd 3rd 4th 5th Final drive ratio gear gear gear gear gear : : : : : : : : : : : : : : : : : : : : : 9.5 + 0.5:1 1400 + 100 rpm. 12.15 kW (16.51 Ps) at 8000 rpm. 15.22 Nm at 6000 rpm. Microprocessor controlled digital C.D.I. 100 BTDC at 1500 rpm. 280 BTDC at 3500 rpm. Unleaded petrol UCAl-MIKUNI BS29, Side Drought, CV Type. : 178.60 cc. : 56.40 mm. : 63.50 mm. : One : Four stroke DTS-i, Natural air cooled.
Technical Specifications
Safety :
Day night mode of Speedo console The turn Indicator, neutral, high beam, and side stand Indicator bulb
glow brightly in the day for clarity, and Intensity reduces during night to reduce irritance to the rider's eye
High RPM warning lamp
when engine reaches to 9000 RPM automatically Red LED bulb starts blinking. This enables the rider to control the speed to avoid damages if any that may take place to engine components.
Engine cut-off at 10000 RPM Spark gets cut-off at 10000 RPM
to bring down the engines RPM for safety.
LED illumination for tell-tale icons on electrical switches that glows in the night for positive access of individual functions.
2 Nos. Champion RG4HC, Bosch UR3DC (Resistive) 0.7 to 0.8 mm. Wet sump, Forced. Kick start / Electric start. Wet, Multidisc type. 5 speed constant mesh. 3.47 : 1 (66/19) 26.93 18.31 13.43 10.54 8.98 : : : : : 1 1 1 1 1 (36/13) (32/17) (29/21) (26/24) (24/26) 2.80 : 1 (43/15)
CHASSIS & BODY

Frame Type Suspension Front Rear Brakes Front Rear Tyres Tyre Pressure Front Rear Front Rear Solo Rear Pillion Rims (Alloy Wheels) Front Rear : : : : : : : : : : : : Double cradle. Telescopic front fork with DU bush (Stroke 135mm) Trailing arm with coaxial hydraulic cum gas filled adjustable shock absorbers, and triple rate coil springs. Mechanically expanding shoe and drum type. Hydraulically operated disc type. Mechanically expanding shoe and drum type. 2.75 x 17, 41 P 100/90 x 17, 55 P 1.75 kg/cm2 (24.5 Psi) 2.00 kg/cm2 (28.0 Psi) 2 2.25 kg/cm (32.0 Psi) 1.60 x 17 2.15 x 17
Technical Specifications
B What is so special in this 'PULSAR DTS-i 180 UG III '? What are the special features of 'PULSAR DTS-i 180 UG III '? OR
Frequently Asked Questions (FAQs)
Fuel Tank Capacity
15 liters Full
3.2 liters Reserve
2.0 liters Usable reserve
CONTROLS
B
Steering
Handle Bar
Pulsar UGIII is next version of Pulsar breed. It is loaded with lots of unique & contemporary features and that distinguishes the Pulsar not only in the category of Power, Performance & Style but also for Comfort, Convenience & Safety from the competition.
Accelerator
Twist grip type on RH side of handle bar
Gears
Left foot pedal operated
Clutch
Lever operated on LH side of handle bar
Apart from refining the power delivery, it is loaded with the features that are meant for cars. So, here is the Comfort, Convenience & Safety of the 4 wheels (cars) available on 2 wheels. The major changes / features are Enhanced Performance Refined engine power delivery by optimization of ExhausTEC location, bigger & twin Air Filter element, optimized valve timing, reduced engine friction etc. Stainless steel silencer that lasts long & overcomes rusting. All sensor type electrical switches that function for the life of the bike. Absolutely no maintenance in absence of mechanical contacts. Enhanced Style Stylish fairing & Headlamp assembly with owl eye, new black mask to separate headlamp from parking lights New age, sharp & attractive 2 Row Tail lamp with LED lights Louver type LH & RH covers with wire mesh gives sturdy look. Ergonomically designed self-letting switches Absolutely no maintenance in absence of mechanical contacts. Enhanced Comfort & Convenience Loaded with Digital Technology like LCD Speed/Odo display, digital fuel meter, Digital trip meter that enables to count two trips. Car like self canceling indicator switches that keeps rider free from switching off the indicators after turn. Apart from digital fuel meter, warning light for low fuel level is provided. Self check provision for tachometer to ensure proper functioning. Oil level inspection window that indicates oils level at a glance. Enhanced Safety Engine cut-off at 10000 RPM Spark gets cut-off at 10000 RPM High RPM warning lamp when engine reaches to 9000 RPM automatically Red LED bulb starts blinking. Day night mode of Speedo console, LED illumination for tell-tale icons on electrical switches that glows in the night for positive access.
Brakes
Front
Lever operated on RH side of handle bar
Rear
Pedal operated by right foot
ELECTRICALS
System Battery Head Lamp Pilot Lamp Tail/Stop lamp Turn signal lamp Turn signal pilot lamp Side stand indicator lamp Hi beam indicator lamp Neutral indicator lamp Speedometer lamp Rear number plate lamp Horn
: : : : : : : : : : : : :
12 V (AC+DC) 12V 9Ah 35/35 W-HS1 5W - 2 Nos. LED 10 W (2 Nos.) LED LED LED LED LED display 5 W 12V DC
DIMENSIONS
mm. mm. mm. mm. mm. (Minimum) mm. (Minimum)
Length Width Height Wheel base Turning circle radius Ground clearance
: : : : : :
1990 750 1090 1320 2180 165
WEIGHTS
Vehicle kerb weight Gross vehicle weight
: :
143 kg. 273 Kg.
PERFORMANCE
Maximum speed Climbing ability
: :
125 km/h with single rider (68kg) 28% (160 Maximum)
Notes:
B
Values given babove are nominal and for guidance only, 15% variations is allowed to cater for production and measurement variation.
How does the digital Speedo work?
All dimensions are under UNLADEN condition.
Definitions of terminologies wherever applicable are as per relevant IS/ISO standards.
Front wheel of the bike has a sensor & magnet unit. The sensor counts no. of pulses w.r.t. wheel rotation & logically calculates number of wheel rotation & gives input to the display unit in the speedo console and the LCD display indicates accurate speed, odo reading & trip meter readings.
Specifications are subject to change without notice.

B What does non-contact Handlebar switches mean?
What are the advantages / Benefits of the digital speedometer apart from giving accurate reading?
This system is totally contact less & no mechanical transmission of drive from wheel to speedometer is available. Thus this system is totally maintenance free & lasts for the life of the bike. B B
The control switches on both sides of the handlebar are conventional to look at, in terms of switch operations & knob position etc. But the key & distinguishing difference is the principle of functioning that means these switches do not function on the basis of physical contact for ON & OFF. These are on non-contact sensor based. This feature will have any wear and tear & hence its life would be more than the life of the bike. These are absolutely maintenance free as far as wear & tear is concerned. The other feature, in these switches is the Illumination of the tell-tale icons that is lit up with LEDs inside the switch body. This gives the icons a pleasant bluish white glow that can be seen in the night clearly & coolly. The tail lamp assembly seems to be too special. What is so in that? Yes. The tail lamp is unique on this vehicle and no other competitor's vehicle has this feature. It consists of 16 (8) nos. of LED bulbs with bi-filaments. The specialties of LED bulbs are - Consume very low current - Glow brightly - Last far long - Totally maintenance free
How the digital fuel indicator meter works? OR How one can understand the available fuel level in the fuel tank? OR How to read the graphical bar of the fuel meter?
Graphic bar with 12-segment display is provided in the speedo console for indicating fuel level in the tank. If the all the 12 segments of a bar graph are 'ON', that indicates that the fuel tank is full. B B
As the float gauge in the tank starts lowering down due fuel level coming down, the segments of the bar graph starts diminishing with corresponding drop in fuel level.
When the petrol level comes down to below four liters, all the segments of the bar will vanish.
Apart from LCD graph bar, a red warning light also has been provided in the console that glows continuously when the petrol level falls down to reserve. And it will be 'ON' till petrol is filled above reserve level.
B B
When the digital fuel meter is available, why the red warning light is provided?
While the LCD graphical bar segments indicates the petrol level in the fuel tank, the red warning light continuously reminds the rider to fill the petrol.
So, the LED tail lamp apart from delivering fantastic performance, it adds to aesthetics. What is this bi-filament bulb? Bi-filament bulb means these LED bulbs have two filaments in each bulb. One filament of lower wattage for parking lights & another for brake lighting, which is of little higher wattage. If so much so electrical /electronic appliances are loaded, it may affect on Battery?
Why two trip meter reading option is given? How is it useful?
It is just to enable the rider to count reading for two different trips unlike only single trip in case of conventional type.
B B
It is like this - on selecting 'Trip1' its will indicate the distance covered in first trip that is set for. In continuation, on selecting 'Trip2', it will indicate the distance covered in the second trip. Then if one wants to know the cumulative distance covered in first & second trip, it can be found in 'Trip1' mode. For this one has to just press/select 'Trip1' mode.
This is an added advantage taken from digital technology! B B
Absolutely not. In fact, all the bulbs & backlit bulbs in the Speedo console (except Head Lamp bulb & pilot bulbs) are of LED type. Few of them works on AC & few are on DC i.e. battery. So there is hardly any drain on the battery as compared to conventional type of bulbs. Moreover, the Battery of this new Pulsar 180 is special & maintenance free. What is this maintenance free Battery? The battery is new development in DC system on two wheelers (in fact, such batteries are introduced in cars earlier than bikes) it is different than the conventional one in the material composition it is made up of. The main features of this new battery are - Electrolyte level checking is required at every one year instead of every fortnight - The unique vent mechanism that do not allow loss of electrolyte - No drainpipe unlike in conventional type battery. So no chances of spillage of electrolyte. B So, in all it is almost maintenance free battery. Moreover, the LED bulbs, & disable function of cranking after 3 successive self starts attempts, will further only enhance the life of the battery.
What do Self-canceling Indicators switches means?
In conventional type of switches, the rider has to manually depress or turn knob of indicator switch for putting 'OFF' the indicator bulbs. In case of this Self-canceling' switches the indicator goes off automatically after the rider takes a turn & brings the handle bar straight. This feature is similar to cars. That means, rider do not have to press or turn the switch to cancel the indicators.
What if one switches ON the indicator and do not physically take a turn? Will it work in such situation?
Yes. Of course. When the rider selects a right or left turn indicator, but changes his mind and physically do not take a turn, the indicators turn 'OFF' automatically after pre-set time. For this a timer function is incorporated in the system. And the timing for this timer is set around 80 seconds.

Sl. 1 LOCK OPERATION STEERING LOCK NOT WORKING/JAM SIDE COVER LOCK NOT WORKING 2 3 FUEL TANK DEFECTS LEAKAGE BLISTERS RUSTY OTHERS 4 5 FRONT / REAR WHEEL OFFSET WHEEL FR. WHEEL TYRE -Free rotation. FRONT WHEEL RUNOUT (SPECIFY) REAR WHEEL RUN OUT (SPECIFY) 7 8 SWITCHES RH switch operations LH Switch operations IGNITION SWITCH SHORT 9 LIGHTS:Side indicator blinking. HEAD LIGHT TAIL/BRAKE LED 10 11 HORN :- DISTORTED/WEAK SOUND(DO NOT SET) Speedo : SPEEDO NOT SENSING. SPEEDO Needle flickering. Tripmeter - 1/2 working -Resetting Odometer working Auto - Calibration of RPM meter Fuel level indication Reserve indication (by red lamp) Red lamp blinking after crossing Engine RPM 9000 Auto-switch off of Ind lamps(H bar straight for > 2 sec) Head light / tail light illumination after 3 seconds LED functioning - Speedounit - Both side indication, Side stand, Neutral, Hi beam, RES ind lamp SILENCER -BAFFLE NOISE 6 FUEL COCK OPERATION - HARD / LEAKAGE (Specify) PAINT FINISH - OVER FLOW (Samples / photographs) Check Points for PDI Check PDI done by BAL/ Service Engg.
Pre Delivery Inspection Checklist

PDI Done by Dealer
What is that disabling of cranking after 3 successive attempts?
A protective device has been incorporated in the system that allows rider to attempt selfstart option (pressing of self-start button) for starting only three times at times. After third attempt the battery power supply gets cut-off to the self-starter motor, thus avoid rider from further cranking of engine by self-start.
This is mainly to protect the battery from over draining by excess attempts of pressing of self-start button to start the engine.
However, one can again use the self-start option after 15 seconds after third attempt.
How come so many features are managed accurately & what is the guarantee of no malfunctioning of these features?
It is needless to say that the digital technology that works with sensors & chips works accurately. To control all the functions of these electronics features, an intelligent device has been installed in the electrical system. This is called BCU (Body Control Unit)
What exactly is BCU (Body Control Unit)? How it controls all these functioning?
BCU (Body Control Unit) is a device that integrates & controls major of all electrical / electronic functions on the vehicle. It is an intelligent device that works on microchip base.
In the eventuality of electrical overloads or short circuits, the built in intelligent protection circuit takes the control of the situation & prevent future damages on other electronic parts. For example:- During night, suppose one of the Head light filament blows OFF then there is a possibility of an accident due to sudden darkness.. To rescue, here the BSU plays an important role. It switches over the Headlight to the other beam automatically without manual shifting of any switches.
It also checks & inspects the fused circuit religiously for any corrections and thus riders' safety is ensured.
Are these type of product features available in Pulsar150cc also?
Presently not. But as in all sphere of life, technology also proliferates. When that happens you may find similar features in Pulsar 150cc also.
Can one alter the current Pulsar model & incorporate these features?
B` No. It is not possible. Physically lot of changes are there that are not easily accommodated in the existing Pulsar.
10
Pre Delivery Inspection Checklist PDI SOP

Check
Description Position SMM 0.80 GP Tools 1
Sl.
Check Points for PDI
PDI done by BAL/ Service Engg. PDI Done by Dealer

Sr. No. Identify & Park Vehicle on Work Bay 0.50 Special Tools
M & T / Service PNR & its Consumables Shop Equipments Attachment Lifter Bay
12
FLAT SPOT (GIVE CO %)
13
2 Remove the Thermocol and additional packing if any. Study PDI card and Work content. Open Petrol tank cap & pour petrol 0.50 0.10 RH RH 0.10 0.10 0.30 12-13 OE Spanner 12-13 Ring Spanner Measuring Jar, Funnel Check for smooth operation of fuel cock lever Check & top up engine oil level, if required. Check clutch cable operation & Adjust if required. Check front brakes for efficient working & Adjust if required. Front / RH
DRIVE CHAIN slack (mention amont of play)
14
BRAKE OPERATION - FRONT/REAR
FRONT BRAKE
3 4 5 6 7
REAR BRAKE EFFECTIVENESS
BRAKE LIGHT REMAINING ON CONTINUOUSLY.
Petrol, Waste Cloth
15
GAP AT THE REED SWITCH AND MAGNETO.
CHECK POINTS FOR PDI
16
LOOSE PARTS
KICK BOSS BOLT
ENGINE MOUNTING BOLT
17
8 Check and correct tyre inflation pressure - Front Wheel Front
ENGINE NOISE
Air Gun
TAPPET NOISE
0.20 Pencil Type Pressure Gauge
CHAIN TENSIONER / TIMING CHAIN
18
ENGINE OIL LEAKAGE
Analogous/Digital type Pressure gauge, Air filling Valve
DRAIN BOLT
9 Check Battery voltage, fill / top-up electrolyte, apply petroleum jelly, connect terminals properly. Inspect Rear Shock Absorber setting & correct if necessary.
MAGNETO COVER
LH
0.60
CRANKCASE JOINT
10
Screw Driver, Distilled water Filler, 10mm T Spanner RH/LH 0.10
OIL FILLING PLUG
Cloth, Fine Polish Paper, Petroleum Jelly, Distilled Water
Hydrometer, Battery Charger, Battery Tester
OHC COVER
11
TAPPET COVER
BENJO BOLT
Check Rear brakes for efficient working & adjust if required.
Rear
0.10
14-15 No. O.E. Spanner
Cloth, Graphite Grease, Fine Polish Paper
CHAIN TENSIONER 'O' RING

12 Check and Correct tyre inflation pressure - Rear Wheel. Rear 0.20 Pencil Type Pressure Gauge
OIL LEVEL INDICATOR WINDOW
OIL FILTER COVER
Analogous/Digital Type Pressure Gauge, Air Filling Valve
19
CLUTCH OPERATION
13 Lubricate chain and Check / Adjust chain slackness if required. LH 0.40
HARD
CLUTCH JUDDERING
Cloth, SAE 90 Oil
Air gun
20
PLATING DEFECTS
HANDLE BAR
14 15 16 17 18 19 Check Choke lever operation Check Accelerator cable free play Check & Adjust TPS Check gear shifter lever operation Check & Adjust steering and Handle bar for free movement. Check front mudguard alignment wrt Front Wheel LH LH LH LH RH / Front Front 0.05 0.05 0.10 0.05 0.20 0.05
20-22, 24-27 Ring Spanner, 10-11 No. OE Spanner, Torque Wrench, Socket Set, Oil Can 10-11 No. OE Spanner 8 & 10 No. OE Spanner 10-11 No. OE Spanner 8 No. T Spanner 12-13, 16-17 Ring Spanner
21
ENGINE OPENING DURING PDI (If any)
(Give engine no & reason for engine opening)
22
FRAME OPENING DURING PDI (If any)
(Give chassis no & reason for chassis opening)
23
OTHER DEFECTS :
MINOR ADJUSTMENTS
24
TRANSIT DAMAGES (Send photographs)
Fork Spanner
Marked if the ok observed
11
12
PDI SOP
Special Tools Whichever comes first M & T / Service PNR & its Consumables Shop Equipments Attachment
Periodic Maintenance & Lubrication Chart

RECOMMENDED FREQUENCY Initial Subsequent Every 2,500km Every 90 days
l l l l l l l l l l Every 5000 kms Every 5000 kms Every 10000 kms l l l l l Every 10000 kms l l R CL,A R C,A C,A C,A C,A C,A C,R C R C,A C,T R Tyre tread wear General lubrication 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. Steering stem bearing Wheel bearing Master cylinder cup and Dust seal Caliper piston seal and Dust seal Swing arm pivot pin Front fork Front fork oil Front brake hose Rr. Shock Absorber- Check gas pressure 7.0+0.5 Kg/cm2 Drive chain Drive chain slack Drive chain wear / Remove & Lubricate Engine compression pressure Cylinder head de-carbonising & valve lapping Valve oil seals L A C,R C CL R l l C,R L L,R C,L R R L C,L R C,R 2 years Every 10000kms Every 500 kms. Every 2500 kms. Every 5000kms. Every 10000kms Every 30000kms Every 30000kms l l l 1 year 1 year l l l l l l l l l l l l l l l 1 Month l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l Every Year l Every 10000 kms Every Year l l l l l l Every 10,000 kms. l l Every 20,000 kms. l l Every 10000kms Every 10000kms Every 2 years Every 2 years Every 5000kms. l Every 10000kms
Sr. No.
Description
Position
SMM
GP Tools
Check all important nut bolts for torque and tightness, OR Days
1. l C,A l A R CL CL R CL,A C,R 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. Rear brake pedal play Brake lining or pad wear Brake fluid level / top up Brake fluid change Steering play All fasteners tightness Engine mounting silent blocks Throttle play Clutch play Brake light switch Battery electrolyte level Spark plugs (2 Nos.) Spark plug / gap Fuel pipes Fuel system leakages Carburettor Air cleaner element Air cleaner element V Oil strainer / Centrifugal filter Engine oil (SAE 20W50 of API SG+JASO MA) Valve tappet clearance Idle speed / CO% Servicing l
Sr. Operation No.
Kms. 750 2,500 5,000 7,500

30~45 105~120 195~210 285~300
20
Pistol Grip PNR
Handle bar mounting bolt Stem lower & upper bracket bolts Stem of bolts Front axle nut Cylinder head nuts Engine foundation bolts Trailing arm bolts Silencer cover shield bolts Both LH/RH engine mtg. bolts
LH/RH
4.00
12-13, 14-15, 16-17, 20-22 Ring Spanner, 22 mm Box Spanner with Handle Ratchet
Check the following and lubricate if necessary
RH/LH Oil Can SAE 20W40 Oil
21
FRONT
1.00
Rear brake lever Rear brake pedal / cam Pillion foot rest Center stand Side stand Kick lever boss Clutch lever
REAR
22
OE accessories fitment Mirrors RH & LH
LH/RH
1.15
17mm OE Spanner
23
OE accessories fitment Leg guard Pistol Grip PNR
LH/RH
3.25
10-12 No. OE Spanner and 12 No. Box Spanner
24
Start vehicle, Check operation of electrical like- Head light, Tail light, Brake light, Side stand indicator, Horn, Speedometer, Odometer, Side indicators, Parking and Pass light working.
LH/RH
0.35
25
Check Idling and CO%.
LH/RH
0.60
Small Screw driver
CO-HC Analyzer; Tachometer, Proper Exhaust Sealing Arrangement of Silencer
26
Trip meter working
LH/RH
0.10
27
Check all locks for proper operation
LH/RH
0.50
28
Test drive the vehicle, check digital speedometer working. Study the job card and verify work done. Take vehicle out and park.
1.30
29
Clean/Wash the veh. before delivery
1.00
Total SMM
17.75
CL Note: Parts / Lubricants to be replaced as per Periodic Maintenance and Lubrication Chart are mandatory and the same are chargeable to customer. C -
Adjust Clean Check
L l : Indicates operation to be performed. : More frequent cleaning may be required when driving in dusty condition. T R
Lubricate Tighten Replace
30
Repair for any other defects seen or observed during test drive.
Expected Output in 480 Minutes / Man / 27 Vehicles
13
14
Periodic Service SOP

Special Tools PNR Consumables SMM PNR GP Tools Sr. Description No. Special Tools M & T / Service Shop Equipments LH/RH Side Consumables

M & T / Service Shop Equipments
Sr. Description No.
LH/RH Side
SMM
GP Tools
1 15 Rear Check & Adjust Rear tyre air pressure. 0.40 Pencil Type Pressure Gauge
Wash vehicle thoroughly.
Both
To be done by washing boy
Identify the Vehicle
0.30
Analogous / Digital Type Pressure Gauge, Air Filling Valve
Bring vehicle & position on bay
0.50
4 16 LH 1.80 Pistol Grip PNR Screw Driver, Distilled Water Filler, 10mm T Spanner
Raise the lift
0.30
Start veh. & Warm up. Remove RH/LH side covers, Seat, Petrol Tank & keep properly.
LH/RH
0.70
12-13 No. Ring Spanner, 12mm Socket
Check Battery, Top-up distilled water. Clean terminals & apply petroleum jelly. Route cables properly and fit terminal caps properly. Recharge battery if required.
Cloth, Fine Polish Paper, Petroleum Jelly Distilled Water
Hydrometer, Battery Charger, Battery Tester
6 Cloth 17 RH Filter Cleaning Stand, Air Gun Clean oil strainer. (Replace - if required) After 1 Year or 10000 Km whichever is later.
Drain Engine Oil
LH
1.30
16mm Socket, Extension, Tommy & Plastic Tray Oil Draining Equipment
Pistol Grip PNR
Clean Air filter. (Replace - if necessary)
RH
3.00
8mm T Spanner
Cloth, 20W40 Oil, Diesel, Air Filter Element 18 Check clutch and Adjust. Float Gauge Cloth, Diesel 19 Fill engine oil. Air gun RH 1.35 RH 0.30
8 No. Box Spanner, 12-13 OE Spanner, 12-13 Ring Spanner, 8mm T Spanner. Plastic Tray, Phillips Screw Driver 12-13 OE Spanner, Small Screw Driver 6 Combination Pliers, Measuring Jar 1Liter, Funnel
Diesel, cloth, Clutch Cover Gasket, Oil Strainer
Drain Carburetor. (Overhaul - if required)
LH
1.30
Phillips Screw Driver, Screw Driver, 10mm Nylon Brush, Plastic Tray, 10-11 & 14-15mm OE Spanner
Cloth, Oil 20W50 of API SG + JASO MA grade
Oil Dispenser
9 20 Filler Gauge 0.01~1mm 21 Cloth, Fine Polish Paper, Spark Plug Spark Plug Cleaner and Tester, Air Gun
Check Accelerator and adjust
LH
0.40
8-9, 10-11 OE spanner
Clean, Check & Adjust RH spark plug.
RH
2.40
Spark Plug Spanner, Plug Cleaner, Wire Brush Front 1.00 Phillips Screw Driver
Filler Gauge 0.01~1mm
Cloth, Fine Polish Paper, Spark Plug Cloth, Oil Dot-4
Spark Plug Cleaner and Tester, Air Gun
10
Clean, Check & Adjust (Replace - if necessary)
LH
2.40
Spark Plug Spanner, Plug Cleaner, Wire Brush
Check and Top-up brake fluid level.
22 Cloth 23
Check/ Adjust
Front
0.50
11
Check & Adjust tappet clearance. (if required) During 4th Servicing or after 5000 Km whichever is later.
LH
Filler Gauge 0.01~1mm Tappet Holder
12-13 Ring Spanner, 5 & 10 mm Allen Key
Cloth, Fine Polish Paper
Air Gun
8-9 No. Ring Spanner, 24-27 OE Spanner, 14 mm Box Spanner with Handle Ratchet, Spark Plug Spanner
Check & Adjust front tyre air pressure.
Front
0.40
Pencil Type Pressure Gauge
Analogous / Digital Type Pressure Gauge, Air filling Valve 24 Check and Adjust steering. Front 0.80 16-17 No. Ring Spanner Fork Spanner
12
Check Side bolts of Front fork Engine foundation bolts Side stand RSA top and bottom nuts Pistol Grip PNR
LH/RH
0.60
14-15, 16-17, 20-22 Ring Spanner, 12 mm Box Spanner with Handle Ratchet, 12-13 No. OE Spanner
25 Cloth, SAE 90 Oil Air gun
RH
1.30
Pistol Grip PNR
13
Adjust chain slackness & Lubricate. Remove and Clean, If required.
LH / Rear
3.90
10mm T Spanner, 20-22, 24-27 Ring Spanner, 10-11 OE Spanner
Check Engine foundation bolts Front axle nut Side bolts of Front fork Handle bar bolts RSA top and bottom nuts Swing arm axle nut Silencer protective cover screws / bolts Rear view mirror Air Gun
10-11, 12-13, 14-15, 16-17, 20-22 No. Ring Spanner, 22 mm Box Spanner with Handle Ratchet
14
Check/ Adjust
Rear
0.50
20-22, 24-27 Ring Spanner, 10-11, 14-15 OE Spanner
Cloth, Graphite Grease, Fine Polish Paper
15
16

Special Tools PNR
Type of Service 1st Free Clutch cover gasket 30~45 105~120 NIL Engine oil NIL Engine oil 195~210 285~300 7000~7500 4500~5000 2000~2500 500~750 Engine oil Days Kms. Limit Part Name
Service Wise Part Kit

Consumables M & T / Service Shop Equipments
Periodic Part Replacement Kit for Free Services Quantity 1000 ml. 1 NIL 1000 ml. NIL 1000 ml. 1 1 2 Spark plug Fork oil 2nd Paid 375~390 9500~10000 Drive chain lock & link set Brake shoes (if worn out) Starter clutch bush Fork oil seal Cylinder head gasket (If required) Front disc pad inspect / replace (If worn out) 3rd Paid 465~480 12000~12500 NIL Engine oil 4th Free 555~570 14500~15000 Drive chain lock & link set Steering cone kit 4th Paid 615~630 17000~17500 NIL Engine oil Clutch cover gasket Air filter foam element Spark plug 5th Paid 705~720 19500~20000 Brake shoes (if worn out) Front disc pad inspect / replace (If worn out) Fork oil Clutch plate Rear brake damper Drive chain lock & link set 6th Paid 7th Paid 8th Paid 795~810 885~900 975~990 22000~22500 24500~25000 27000~27500 NIL Carburettor insulator Chain sprocket kit NIL 330 ml. 1 1 1 2 1 1 NIL 1000 ml. 1 1 NIL 1000 ml. 1 1 2 1 1 330 ml. 1 1 1 NIL 1 1 NIL
Sr. Description No.
LH/RH Side
SMM
GP Tools
Lubricate
26 Grease Gun
2nd Free 3rd Free 1st Paid
20W40 Oil, Graphite Grease, Cloth Pistol Grip PNR

Clutch cover gasket Air filter foam element
Clutch lever Rear Brake pedal Rear Brake Cam Pillion Foot Rest Center Stand Side Stand Kick lever boss pin
LH/RH
0.80
Oil Can
27
Refit RH, LH side covers, Seat, Petrol tank
LH/RH
0.50
12-13 No. Ring Spanner, 12mm Socket Air Gun
28
Check and Clean fuel line & Clean petrol tank. (Replace fuel pipe - if required)
LH
0.50
29
Check all Meters for proper functioning & Correct, if reqd.
Front
0.50
30
Start vehicle, Check & Adjust the following.
RH
Head light.
Front
Screw Driver
Tail light.
Rear
Brake light.
RH/Rear
0.95
Horn
Front
Phillips Screw Driver
Speedo, Pass, Parking light
Front
Side Indicators - Front & Rear
Both
30
Tune Engine & Carburetor.
LH
2.00
Small Screw Driver
CO-HC Analyzer, Tachometer, Proper Exhaust Sealing Arrangement of Silencer
31
Study Job Card. Verify work.
1.00
32
Lower the Lift
0.30
33
Take vehicle out and park
0.50
Sub Total
32.50
34
Carry out any additional work as indicated by the Customer or as required.
10.00
Total SMM
42.50
Expected Production / 480 minutes / Man / 11
35
Test Ride of the Vehicle if required and park.
1.5
To be Carried out by Expert
36
Clean the vehicle at the time of delivery.
Will be done by Delivery boy
PNR = Pneumatic Nut Runner
17
18
Service Wise Part Kit

Cleaning
Part Name Quantity 1000 ml. 1 1 2 1 1 4 1 1 1 330 ml. 1 Engine oil Clutch cover gasket Air filter foam element Spark plug Valve oil kit Cylinder head gasket Cylinder head stud copper washer Brake shoes (If worn out) Front disc pad inspect / replace (If worn out) Steering cone kit Fork oil Drive chain lock & link set
Schedule Maintenance
Periodic Part Replacement Kit for Free Services
Type of Service
Days
Kms. Limit
The vehicle must be cleaned periodically using pressurized water. Before cleaning the vehicle cover the important parts like Ignition switch, Silencer Tail end, CDI unit, H.T. coil with plastic bags. Dont apply the jet of water directly on electrical parts such as Switches, Ignition unit, Coils etc. otherwise they may get damaged. Brushing with kerosene and wiping dry with clean rag is advisable for external cleaning of the engine. All painted surfaces should be washed with water. Do not use kerosene or hard detergent soap on painted surfaces as it damages the paint and turns it dull. After washing, dry the vehicle with compressed air and carry out the lubrication as recommended
Caution : Water may enter on the brake liners during washing & brake slippage may occur. Ensure that brake liners are dry before driving the vehicle.
9th Paid
1065~1080
29500~30000
Periodic Maintenance
Periodic maintenance (in accordance with the periodic maintenance chart) of a vehicle is most important to prolong vehicle life, trouble free running and ensure your safety while driving.
Use always Genuine Bajaj Auto parts & recommended lubricants. (Engine oil: SAE 20W50 API SG + JASO MA grade)
Notes :
Engine Oil Level Checking

Park the vehicle on level surface on center stand to check the oil level. Inspect the oil level through oil inspection window
Upper Level Mark Lower Level Mark
It should be in between upper and lower mark Top up if required

Recommended Oil Grade and Qty Grade Quantity SAE 20W50 of API SG + JASO MA Drain & Refill 1000 ml. Engine Overhaul 1100 ml. Note : It is most vital to adhere to recommended frequency of oil change for the purpose of long life of critical engine components for details refer Periodic Maintenance Chart.
Oil Strainer Cleaning
Remove : Drain engine oil. Clutch cover Oil pump mounting bolts (A) (3 Nos.) Pump with strainer. Clip (B) and take out Oil Strainer from oil pump.
19
20
Air Filter Cleaning Clean Air filter element adhering to standard SOP
Remove :
Clean oil strainer with Kerosene / Diesel blow compressed air and then refit it. Replace oil strainer if found damaged.
1st Stage: Clean with Kerosene
3rd Stage: Dip into Engine Oil (20W40)
Centrifugal Oil Filter Cleaning:
Remove : Centrifugal oil filter cover mounting screws (C) 3 Nos. The cover with gasket Replace gasket if damaged Clean centrifugal oil filter using Nylon brush/kerosene or Diesel
Squeeze
Squeeze and Remove Excess Oil
Air Filter
Air Cleaner Element Removal
Remove :
RH side panel by unlocking it with key
2nd Stage: Clean with Kerosene Again Dry with Cotton Cloth
Remove :
2 bolts (A).
Air filter cover (B).
Blow Low Pressure Compressed Air
Remove : Air Filter Element Cleaning and Inspection

Note : In dusty areas, the element should be cleaned more frequently than the recommended interval. After riding through rain or on muddy roads, the element should be cleaned immediately. Since repeated cleaning opens the pores of the foam element replace it with a new one in accordance with the Periodic Maintenance Chart. Also if there is a brakage in the element material or any other damage to the element replace the element with a new one.
Air filter element assembly along with catrej
Seperate foam filter from the catrej
Note : No need of removing flame arrestor White colour filter portion towards carburettor side Ensure beading placed properly when fitting cover
Warning : Clean the element in a well-ventilated area, and make sure that there are no sparks or flames anywhere near the working area. Because of the danger of highly flammable liquid, do not use gasoline/petrol or a low-flash point solvent to clean the element.
21
22
Position Champion RG4HC / Bosch UR3DC 0.7 ~ 0.8 mm After every 10000 Kms.
Note : Std setting is done in 2nd notch
1 Stronger 2 3 4 5 Spring Action
Spark Plug
Recommended Spark Plug
Electrode Gap
Replace Spark Plug
If the Shock Absorber sleeves on both sides are not adjusted to the same position, an unsafe riding condition may result.
Battery - 12V - 9 Ah
Nitrox Air Filling

Procedure for gas checking and Refilling Remove the Phillips-headed small screw and O ring. Clamp the cylindrical guide clamp on to the canister keeping the rubber plug in the center to support the syringe needle insertion and keeping in position. Hold the pump as shown and pierce the syringe needle into the center of rubber plug. The molded needle adaptor will rest into the clamped cylindrical guide Read the gas pressure on the dial gauge. If the gas pressure is below 6.5 Kg/cm2 refill the air by pumping, keeping the needle in as it is condition without removal. As the natural air consists of 71% of nitrogen it will serve the purpose. To fill the air into the canister, apply full stroke of pump as shown; otherwise air will not get inflated into the pump. Keep on pumping the air unless you get 7.5 kg/cm2 on the gauge Pull out the air pump along with needle carefully and take out the guide clamp Finally fix the phillips headed screw with O ring.
Battery is located inside LH cover
Check the electrolyte level in each cell and ensure that the level is between the upper and lower level lines.
Remove the battery filler caps and fill with distilled water until the electrolyte level in each cell reaches the upper level line if required.
Note : Add only distilled water to the battery. Tap water is not a substitute for distilled water and will shorten the life of the battery.
Apply petroleum jelly on to the terminals
Front Brake Fluid Level
Front brake fluid master cylinder reservior is located near RH switch on handle bar.
To check oil level, park the vehicle on Main / Center stand with handle bar in straight position.
Always ensure that brake fluid level is above MIN mark given on inspection window.
Use only DOT-3 or DOT-4 brake fluid (from sealed container) to top up if required.
Note : It is advisable that brake fluid should be replenished once
in a year.
Drive Chain Slack / Lubrication

Set the motorcycle upon its center stand. Rotate the rear wheel to find the position where the chain is tightest & measure the vertical movement midway between the sprockets. If the drive chain is too tight or too loose, adjust it so that the chain slack will be within the standard value. Check drive chain slackness at every 1000 kms. Drive Chain Slackness : 25 ~ 30 mm Service Limit 35 ~ 45 mm
Rear Shock Absorber
The rear shock absorbers can be adjusted to one of five positions to suit riding conditions. Using special tool adjust the required position you desire. They can be left soft for average road riding condition but should be adjusted harder for rough road condition.
Shock Absorbers adjusted either too soft or too hard adversely affect riding comfort and stability.
To adjust the Rear Shock Absorbers
Turn the adjusting sleeve on each shock absorber to the desired position. The higher the adjuster sleeve is positioned, the stronger the spring tension, and the harder the ride.
Check to see that both sleeves are turned to the same relative position.
23
24
Tyre Air Pressure
Keep appropriate tyre pressure as mentioned below to increase life of this tyre and for better fuel consumption. Front Rear - with Solo Rear - with Pillion 1.75 Kg/cm2 (25 PSI) 2.00 Kg/cm2 (28 PSI) 2.25 Kg/cm2 (32 PSI)
Drive Chain Cleaning / Lubrication
1st Stage:
Clean with Kerosene
2nd Stage: Important Adjustments and Checking Procedures

Idling Speed Adjustment
Clean with Cleaner Kerosene again
Blow Compressed Air
Whenever the idling adjustment is disturbed follow the procedure given below for setting proper engine idling. Start engine & drive it for at least 5 kms. or warm the engine till the oil temp reaches 600C. Remove the Bolt/Plug near Exhaus TEC Connect the probe of CO analyser. Set the CO between 1.75 ~ 2.25% by adjusting volume control screw. Then set the engine idling r.p.m. by rotating the idle adjustment screw clockwise or anticlockwise by hand. For the precise adjustment of idling speed, use of tachometer is recommended. Rotate the throttle a few times to make sure that the idling speed does not change. Readjust if necessary. Do not attempt to compensate for faults in other systems by adjusting the idle speed. Idling Sped : 1400 + 100 rpm
3rd Stage:
Dip into SAE 90 Oil
Tappet Clearance Setting

Ensure that the engine is cold. Ensure the T mark on the Rotor match with the mark on the Crankcase LH. At this stage the Piston is at TDC and both the Tappets are free. Holding tappet screw firmly with special tool loosen the tappet screw nut. Put the feeler gauge, measure and adjust the clearance. Lock the nut holding screw with special tool after getting desired clearance. Again check the tappet clearance with gauge. The gauge should slide with slight resistance between tappet and valve stem head feeler and tighten the check nut with a spanner. Inlet Valve : 0.05 mm Exhaust Valve : 0.1 mm Special Tools : Feeler Gauge - 69 7502 51 : Valve Adjusting Screw Holder - 37 1031 53
Soak into SAE 90 Oil
Final Stage:
Hook Chain for dripping of excess oil
25
26
Reed Switch Setting and Checking
Check throttle lever movement by rotating it with hand. It should not be sticky in operation and should return back it self on releasing. bracket Multimeter should show continuity.
Gap 2.5mm max.
Ignition Timing Inspection
Connect cable of stroboscope to one of the H. T. Coil carrying current to spark plug. Magnet should not touch with reed switch.
Start the engine.
Aim the stroboscope light at Magneto cover glass window.
At idling speed the F marked line on the rotor coincide with the line mark on magneto side ccase. (100 BTDC @ 1500 rpm).
Gap between Magnet & Reed Switch should not be more than 2.5mm. Movement of throttle lever with magnet assembly and Reed Switch fitted should be free.
As the engine rpm is increased the A marked on the rotor coincide with the line mark on magneto side ccase. (280 BTDC @ 3500 rpm).
Reed Switch : Setting

Accelerator cable play: 2-3 mm by adjusting the Adjuster Protude stopper of the throttle lever bracket must on idling screw tip.
This indicates the advance timing is functioning correctly.
Remember the T marked line is a reference line for TDC position of the piston and is not for Ignition timing.
B
0.00
Clutch Lever Free Play Adjustment Reed Switch : Checking

Keep throttle at zero position. On connecting multimeter to Reed Switch coupler it should show continuity.
Slide the dust cover at lever yoke end.
Check that the clutch cable outer end is fully seated in the adjuster.
Turn the adjuster (A) until the proper amount of free play can be obtained.
Tighten the lock nut (B) against the adjuster. If the clutch free play cannot be adjusted with the adjuster at the handle bar end, use the adjuster at the lower ends of the clutch cable situated on clutch cover.
C
1
Loosen the 2 lock nuts (C) on clutch cable bracket and adjust threading in the adjuster provided on the clutch cover. Tighten both the lock nuts on clutch cable bracket by holding one nut and tightening the other, after the required free play.
Clutch Lever Free Play : 2 ~ 3 mm
When throttle is open and Reed Switch magnet crosses to straight edge of fix bracket of Reed Switch multimeter should show discontinuity.
Accelerator Free Play Adjustment
Turn the adjuster (A) until the proper amount of free play can be obtained.
Tighten the lock nut (B) against the adjuster.
If the accelerator free play can not be adjusted with the adjuster at the handle bar end, use the adjuster at the lower ends of the Accelerator cable situated on carburettor.
0.00
Loosen the 2 lock nuts (C) on accelerator cable bracket end adjust by adjuster (D) provided on the cable.
Tighten both the lock nuts on bracket by holding one nut and tightening the other, after ensuring the required free play.
On De-acceleration, when of Reed Switch magnet re-coinsides with straight edge of fix bracket of Reed Switch Multimeter should show continuity.
Accelerator Grip Free Play : 2 ~ 3 mm
27
28
Compression Pressure Testing
Standard Checking Procedure

For testing the compression pressure first warm up the engine. Remove the spark plug. LH side.
Caution : side. Disconnect H. T. lead cable from second spark plug i.e. RH
Front Brake Free Play Adjustment
There is no need for free play adjustment, since the pistons in caliper assembly will move towards the pads and take new positions in order to automatically compensate for pad wear. The free play will be approximately 2 ~ 3 mm.
Front Brake Lever Play : 2 ~ 3 mm.
Fit the compression gauge with adapter in the Spark plug hole. Open the throttle fully then kick 5 times instantaneously. Note the reading in the compression gauge. Release the pressure by pressing the release valve on hose pipe. Take average of 3 such readings for noting actual compression pressure. Confirm the compression pressure is between 6 to 10 Kg/cm Wet Compression Test : If the compression pressure is found below lower limit than specified, put few drops of engine oil through the spark plug hole and again check compression pressure. If you find considerable increase this time, then cause for the low compression pressure lies in Cylinder / Piston assembly. If compression pressure remains the same, then the cause for low compression pressure lies in Cylinder / Head assembly.
Caution : If wet compression is done, remove second spark plug and clean thoroughly to avoid oil fouling before fitment.
2
Rear Brake Pedal Adjustment
Check the rear brake pedal play as stated below. If it is more or less than the standard, adjust the rear brake.
Depress the rear brake pedal lightly by hand. This is free play.
If the rear brake pedal free play is incorrect, adjusting the rear brake shoe adjuster nut (A).
Operate the pedal (B) for few times to see that it returns to its rest position immediately upon release.
Rotate rear wheels to check for brake drag.
Check braking effectiveness.
If there is any doubt as to the conditions of the brake, check the brake parts for wear or damage.
Turn the adjuster until the rear brake pedal have the correct amount of play.
Rear Brake Pedal Play : 25 ~ 30 mm.
Rear Brake Pedal Position Adjustment
Chain Slack Adjustment :

Set the motorcycle upon its centre stand. Rotate the rear wheel to find the position where the chain is tightest and measure the vertical movement midway between the sprockets. If the drive chain is too tight or too loose, adjust it so that the chain slack will be within the standard value i.e. 25-30 mm. Loosen the rear torque link nut (A) & rear brake adjusting nut (F). Loosen the left and right chain adjuster lock nuts (B). Loosen the axle nut (C). Loosen the bearing carrier nut (D). If the chain is too tight, back out the left & right chain adjusting nuts evenly & kick the wheel forward until the chain is too loose. F A Turn both chain adjusting nuts evenly until the drive chain has the correct amount of slack. To keep the chain and wheel properly aligned, the notch (E) on the left chain adjuster should align with the same swing arm mark that the right chain adjuster notch (E) aligns with.
Warning : Misalignment of the wheel will result in abnormal wear, and may result in unsafe riding condition.
To suit rider foot comfort / operating style the angle of the rear brake pedal can be adjusted by loosening the lock nut (A) and adjusting the bolt (B).
Ensure free play by turning the adjuster clockwise or anticlockwise to achieve specified free play. Fix the rubber sleeve on the bolt.
Note : After pedal position adjustment, it is necessary to set the free play.
Rear Brake Light Switch Adjustment
When either the front or rear brake is applied, the brake light glows on. The front brake light switch requires no adjustment but the rear brake light switch should be adjusted in accordance with the periodic maintenance chart. Inspection : Turn on the ignition switch. The brake light should go on wheel the front brake is applied. If it does not, then inspect the front brake light switch. Check the operation of the rear brake light switch by depressing the brake pedal. The brake light should glow after about 15 mm of pedal travel. If it does not, adjust the rear brake light switch. Adjustment : Adjust the rear brake light switch (A) by rotating the switch nut to create adequate tension in spring to operate the switch.
29
30

Air Bleeding of Disc Brake System :
Tighten both chain adjuster lock nuts.
Tighten the sleeve nuts securely.
For air bleeding from front Hydraulic brake system first top up the master cylinder with hydraulic oil. Operate the brake lever slowly in order to get filled the oil in the circuit.
Connect transparent tube to the bleeder screw at caliper Operate the brake lever and keeping in pressed position loosens the bleeder screw so that some oil escapes with the air bubbles. Keep on operating the brake lever till the air bubble escape out completely through bleeder screw, and top up the master cylinder if required. Once the air escapes out from the hose pipe the brake lever meets resistance, which indicates completion of air bleeding After completing the bleeding, top up the master cylinder up to the maximum level mark.
Warning : Tighten the bearing carrier nut before tightening the axle nut. If the nut tightening order is reversed, the rear axle will not be securely mounted on the swing arm. This may cause misalingment of the wheels and result in loss of control.
Nitrox Air Filling

Remove the Phillips head screw & small O ring fitted on air valve of Nitrox RSA. Fix the guide to canister of Nitrox shocker in such a way that guide hole is concentric with air filling valve.
Center the brake panel assembly in the brake drum. This is done by tightening the axle nut lightly, spinning the wheel, and depressing the brake pedal forcefully. The partially tightened axle nut allows the brake panel assembly to center itself within the brake drum. Tighten the Axle Nut Tighten the torque link nut Fix the snap ring Adjust the correct brake play
Note : This procedure can prevent a soft or spongy feeling brake.
Insert the Nitrox air filling pumps needle end into the guide & carefully pierce the rubber pin fitted inside the air valve of Nitrox RSA. Note the pressure indicated by pressure gauge of Nitrox air pump. Refill the pressure. Once the pressure reaches upto 7.5 Kg/cm2, take out the needle slowly from canister. Fit the Phillips head screw & small O ring fitted on air valve of Nitrox RSA.
Piston Ring Fitment :
Piston rings must always be fitted with respect to exhaust mark on the piston.
First place the bottom oil rail ring with end gap 280 towards left of the exhaust mark in the last groove.
Place oil expander ring with butting end downward and end gap facing opposite to the exhaust mark.
Power Up the Jig

The Jig should carry out a self test, where first all Red LED; glow sequentially and then all Green LED; flash twice.
Now fit top oil rail ring on the expander ring with end gap 300 towards right of the exhaust mark.
Fit the second piston ring with Top 2 mark facing upward and end gap facing opposite to the exhaust mark.
Manual Testing
Connect wiring harness to C1 connector. Through this harness the following testing can be carried out : - Vehicle sensor speed. - Hall sensor. - Starter relay.
Finally fit the first ring with Top 1 mark upward and end gap facing towards the exhaust mark.
Remember fitment of 2nd ring upside down may lead to passing of oil above the piston and ultimately leading to smoky exhaust.
31
32

Details of Exclusive Special Tool
Special Tools
LCD Speedo Console Test
Connect wiring harness number 2 to C2 connector.
After connecting speedo console wait unitl console LCD goes blank.
Engine
For carrying out repairs / overhauls, 1 new special tools for Pulsar DTS-i UG III have been developed. Rest of the special tools required remains the same which were earlier required for Pulsar and Pulsar DTSi
Now press speedo console test switch to start the test.
Observe for working of speedo console till test ends. Sprocket Catcher Drawing No.: 37 10DH 36
Body Control Unit (BCU) Test
Connect wiring harness number 3 to C3, C4 and C5 connectors respectively.
Press the BCU test switch.
At the end of complete test, Green colour glowing of Result LED indicates BCU test passed.
Application : For holding sprocket during removal / refitting of Cam sprocket allen bolt. Camshaft Big Bearing Puller Drawing No.: 37 10DH 32 Application : To remove bearing (Decompression assembly side) of camshaft.
At the end of complete test, Red glowing of Result LED indicates BCU test failed at respective Red indications.
Camshaft Small Bearing Puller Drawing No.: 37 10DH 31 Application : To remove small bearing of camshaft.
Rocker Pin Remover Drawing No.: 37 10DH 35 Application : To remove rocker pin from cylinder head.
Silent Bush Puller Drawing No.: 37 10DH 33 Application : To remove silent bush from cylinder head cover.
33
34
Special Tools
Bearing Extractor Drawing No.: 37 10DJ 76 Application : Used to extract the input shaft bearing from crankcase LH.
Special Tools
Rotor Puller with Butt Pin
Drawing No.: 37 10DJ 32
Application : Used to pull out the rotor from crankshaft assembly.
Primary Gear Holder Drawing No.: 37 10DJ 77
Bearing Puller
Application : Use to hold primary gear while loosening / tightening the clutch nut.
Application : Used to pull out the bearing for body balancer from crankcase LH.
Balancer Gear Holder
Adaptor & Valve Spring compressor
Application : Used to load the pre-tensioned scissor gears of Assly balancer Idler gear.
Adaptor - Drawing No.: 37 10DJ 78 Valve Spring Compressor - Drawing No.: 37 1031 07 Application : Used for assembling / dismantling inlet, exhaust valves by compressing spring in cylinder head. Rotor Holder Drawing No.: H6 0721 00 Application : To hold rotor while loosening bolt.
Special Nut
Application : Used to remove / fit of centrifugal oil filter nut.
Dia. = 25.9+0.1
Note : Existing tool can be used by reducing diameter to 25.9 + 0.1 mm
Piston Ring Holder
Drift Drawing No.: 74 9309 89 Application : To remove piston pin.
Application : Used for compressing the piston rings when assembly piston in the cylinder block.
Bearing Race Extractor
Thrust plate aligner/holder Drawing No.: T-1011168 Application : To align the clutch hub concentricity w.r.to clutch wheel, clutch housing and thrust plate
Application : Used for removing the lower bearing race from T
35
36
Special Tools
Chassis
Special Tools
Crankshaft Bearing Extractor Fork oil seal fitment punch Drawing No.: 37 0040 03 Application : To fit fork oil seal on outer pipe
Drawing No.: 37 1001 14
Application : To remove bearing from crankshaft
Output Sprocket Holder Rear Shock absorber adjuster Drawing No.: 37 00DH 14 Application : For adjusting the notch position of RSA to achieve hard or soft rear suspension Fork Inner & Outer Tube Extractor Drawing No.: 74 9310 15 Application : Used for removing front fork inner tube from outer tube.
Drawing No.: 37 1030 53
Application : To hold the output sprocket while removing sprocket bolt
Bearing Driver Set
Drawing No.: 37 1030 61
Application : Common bearing driver set for fitting and removing bearings from crankcase.
37
38
Carburettor and Fuel System

Fuel Tank
Turn the fuel tap to the off position. Pulsar 180cc Ucal-Mikuni BS29 DJ - U3 1400 +100 2.5 +2 turns out 117.5 Remove : Side cover LH and RH by unlocking it with key. 4DHL42 922MP-1 2nd from top 17.5 Fixed type Fixed type 2 stage with push pull type mechanism Remove : Pull the cable from the cover LH to unlock the seat lock Seat assembly
Carburettor
Specifications :
Item
Disconnect the fuel pipe connections from the petrol cock. Disconnect the fuel indicator wiring harness connection.
Make and Type
Identification No.
Idling Speed
VC Screw setting
Main Jet
Jet needle mark
Needle jet mark
Jet needle clip position
Pilot Jet
Note : To remove the side covers LH and RH, unlock with the key then hold the front end of the cover and pull the front end out then pull the cover in forward direction to remove it from the lug.
Starter jet
Throttle valve
Chock Lever
Notes :
Note : To remove the seat assembly hold the seat assembly and lift it from the rear end and pull it back.
Remove : 1 bolt (A). Fuel gauge wiring connection. Drain pipe connection. Fuel pipe connection. Fuel tank assembly
Note : To remove the fuel tank assembly from the chassis lift the fuel tank assembly by holding it at the rear end and pull it back.
Fuel Tank Inspection Remove the hoses from the fuel tank, and open the tank cap. Check to see if the breather pipe and water drain pipe in the tank for clogging. If they are clogged, remove the tank and drain it, and then blow pipes free with compressed air. Fuel Tank Cleaning
Warning : Clean the tank in well ventilated area, and take care that there are no smokes or flame anywhere near the working area. Because of the danger of highly flammable liquids, do not use gasoline or lowflash point solvents to clean the tank.
39
40

Bowl Strainer Gasket Selector Body 2 hole subber seal
Remove the fuel tank and drain it. Pour some high-flash point solvent into the fuel tank and shake the tank to remove dirt and fuel deposits. Pour the solvent out of the tank. Dry the tank and the fuel tap with compresses air. Install the fuel tank.
Note : While installing the fuel tank on chassis make sure that the dampers (A) on petrol tank are mounted on the chassis.
Notes :
Fuel Tank Cap Dismantling
To unlock the Fuel tank cap, insert the key in the key slot and turn it anticlockwise direction and lift open the tank cap. bolts (A) Fitting is the vent hole. To
Now remove the anti theft screw and then remove the allen and remove the fuel tank cap assembly from the fuel tank. the reverse procedure of dismantling. But take care that hole is free from any foreign particles that may clog the lock the fuel tank cap, just press the cap without key.
Fuel Cock Removal
Remove :
2 bolts (A)
Fuel cock assembly from the fuel tank.
Note :
Always loosen the bowl of the fuel cock on vehicle itself
Check the fuel cock strainer for any breaks or deterioration.
If the fuel cock strainer have any breaks or are deteriorated, they may allow dirt to reach the carburettor, causing poor running. Replace the strainer.
Clean the fuel cock strainer in a high-flash point solvent.
Pour high flash point solvent through the cock in all lever positions.
Dry the tank and the fuel cock with compressed air.
Install the cock in the tank.
41
42
Working of Carburettor
Pilot Circuit : Constant Velocity Carburettor
Cut Section View of Mixing Chamber
1. Pilot Jet 2. Pilot Outlet Hole 3. Butterfly Valve 4. Volume Control Screw 5. Idling Adjustment Screw 6. Fuel Inlet
Starter Circuit : Constant Velocity Carburettor
Air inlet for choke
Towards Engine Towards Engine
1. Plunger Cap 1. Plunger 2. Mixing Chamber 3. Starter Jet
2. Diaphragm Cap
3. Diaphragm Piston Valve
Towards Engine
Air Inlet for pilot jet
4. Piston Valve with Jet Needle
5. Float Chamber
Function
Function
The pilot circuit provides the air fuel mixture at idling when not enough air is being drawn through the carburettor to cause the main circuit to operate.
The function of starter circuit is to provide rich air fuel mixture on starting / cold starting. At cold engine condition the air is dense also the engine parts are cold enough this does not allow the petrol to vaporize properly this leads to starting trouble.
Construction
The pilot circuit consists of pilot jet, pilot air jet and volume control screw. The pilot jet meters the fuel and the pilot air jet meters the air quantity. The volume control (VC) screw controls the amount of air fuel mixture flowing through the pilot outlet.
Construction
The Starter Circuit consists of a starter jet and a plunger. The starter jet is used to meter the fuel and a plunger that opens an air passage from the inlet of the carburettor (underneath the diaphragm) which passes the mixture to the mainfold.
Working
As the air enters the pilot air inlet the fuel is metered by pilot jet and air quantity is metered by pilot air jet. The atomized / vaporized mixture is discharged through the pilot outlet. The pilot outlet is located on the manifold side of the carburettor. Since the throttle valve is almost at fully closed position, air fuel mixture is supplied mainly by pilot outlet only. Air fuel mixture volume is adjusted by volume control (VC) screw and mixture becomes lean when volume control (VC) screw turned clockwise and rich when it is turned Anticlockwise direction.
Working
On pulling the choke lever the plunger is lifted by a cable. This uncovers the fuel passage that leads to the starter jet, air inlet passage and the outlet passage towards the manifold. This creates enough suction to draw fuel up from the bowl into the mixing chamber (below the plunger). Here the fuel is mixed with the air and the mixture is drawn into the engine through the outlet passage.
43
44
1. Pilot Jet 2. Pilot Outlet Hole 3. Bypass / Progression Holes 1. Piston Valve 2. Piston Valve Diaphragm 3. Jet Needle 4. Needle Jet 5. Jet Holder 6. Main Jet 4. Butterfly Valve 5. Volume Control Screw 6. Throttle Lever
Main Circuit : Constant Velocity Carburettor
Progression Circuit : Constant Velocity Carburettor
Towards Engine
Air Inlet for main jet
Function
Air Inlet for pilot jet
The Main Circuit provides air fuel mixture by lifting up the piston valve in direct proportion to the engine demand. This assures the correct venture size & air velocity throughout the mid range operation of the engine.
Towards Engine
Construction
This circuit consists of jet needle, needle jet and main jet. To assist in atomization an air bleed circuit is incorporated in the main metering system and it aids fuel vaporization by introducing the air into the fuel before it enters the main air stream. The piston valve movement is controlled by spring and carburettor venture vacuum which is generated below the piston valve diaphragm.
Function
The progression circuit provides the air / fuel mixture at small throttle opening when pilot circuit is still working but unable to meet the engine demands on small throttle opening.
Working
When the butterfly valve is opened and air flow through the venturi increases, the air pressure in the venturi (and the upper chamber) decreases. As the atmospheric pressure in the bottom chamber is greater than the venturi pressure above the diaphragm, the piston valve along with jet needle is pushed up and more air fuel mixture is drawn into the engine from main jet through needle jet into the main air stream. When the butterfly valve is closed, air flow through the venturi decreases; air pressure in the venturi increases and approaches atmospheric pressure, & the spring pushes the piston valve along with jet needle down.
Construction
The progression circuit follows the path of pilot circuit and the construction is same as that of pilot circuit.
Working
As like pilot circuit the fuel is metered by pilot jet and air volume is metered by pilot air jet. This mixture in vaporized / atomized form is discharged through the bypass ports when the butterfly valve is opened from idling further.
45
46
Working of Carburettor Digital Twin Spark Plug Ignition (DTS-i)
Dos
1. Never use oversize screw drivers. Do not over tighten the jets and screws. These will damage the jets and their seats. 2.
Donts
Pulsar DTSi is the first bike in the world (In small cc engine) to have twin spark ignition system.
Handling
Use appropriate screw drivers.
The most obvious feature is the Twin Spark Plug configuration o f the Engine. The cylinder head has 2 spark plugs one on either side. The spark plugs are of the smae Heat range (Champion RG4HC/Bosh UR3DC (Resistive) and have similar electrode gaps. These also spark simultaneuosly, This has been done to improve the combustion process by reducing the time of combustion. The end results are low emissions, good fuel economy and good driveability
Cleaning
Never clean the carburettor with water. Jets & air passages will get clogged due to sediments if cleaned by water.
For cleaning always use carburettor cleaner like - Acetone - Carbon Tetra chloride - Aerosol - CVC spray 3.
To enable the sparking of the 2 spark plugs, a intelligent CDI capable of handling this was developed. Further more, the ignition timing has been optimised to give the best output from engine (100 BTDC @ 1500 rpm, 280 BTDC @ 3500 rpm). To enable optimum igntion timing for part throttle loads and full throttle loads, there are separate igntion maps stored in the memory of the CDI. These are activated depending on the throttle opening and engine speed. The Digital CDI has a bit Microprocessor which handles all these inputs and gives out the required and correct spark advance. The intelligent CDI can be easily indentified by 2 green dots marked on CDI case. To enable switching the required igntion maps, a magnetically operated need switch is incorporated on the carburettor throttle shaft and carburettor body. This is known as TRICS. Throttle Responsive Igntion Control System. 4.
Maintenance
Replace Jets - Worn out jet. - Incorrect size jet.
Ensure Jets - Holes are clean. - Holes are not worn out. - Size as per specification.
Float is in good condition.
- Punctured, Squeezed and distorted float.
Float Pin - Tip having no wear mark. - Spring loaded pin is free in movement.
- Worn out tip. - If spring loaded pin is sticky.
These engines are capable of of reviving very high, quite easily. To keep them mechanically safe, a engine rpm limiter has been incorporated in the Digital CDI. This curtails the sparks to the spark plugs thereby limiting the engine rpm Max upto 9000 and thus keeps the engine mechanically safe. There are 2 spark plugs. LH spark plug fires at 350 rpm and then continues to give spark till at 9000 rpm of engine. The spark is cut off from LH plug 9000 rpm to protect engine from excessively high speed. RH spark plug gives spark at 750 rpm and then continues to give till 6000 rpm of engine. If engine rpm exceeds 6000 rpm then RH plug is cut off. This is done to reduce combustion noise created in engine. 5. 6. This engine has been extensively tuned for more Power and Torque. The DTSi technology has enabled the Pulsar to meet 2006 norms without any Secondary air injection devices. Troubleshooting : Malfunctioning of the Reed switch assly will not harm the engine, neither it will give any physical indicators like starting trouble or misfiring. However checking of proper functioning of Reed Switch Assly at PDI and at every service is essential. Following symptoms may indicate as malfunctioning of Reed Switch Assly as one of the cause. Symptom Cause Remedy Sudden drop in mileage & power The igntion systems is working only Replacement of Reed Switch Assly lack in mid range rpm in 2nd map due to reed switch is stuck in open circuit
Needle Jet - No wear at taper portion. - Circlip position is in specified groove. - Needle worn out at taper portion.
Piston valve - No wear mark. - Diaphragm condition.
- Piston valve worn out. Scoring marks. - Diaphragm punctured.
Overhaul carburettor at every 10,000 kms. and insepct the parts.
47
48
Digital Twin Spark Plug Ignition (DTS-i) Important Points to Remember
Customer Eductaion Tips : While starting the engine in any case throttle should not be rotated more. Even if this happens, engine will start, but the engine rpm will shoot uo too much (due to too high throttle opening) Whenever there is a sudden subtantial drop in mileage, customer should report to Bajaj Autos Authorised Service Centres.
Remove the Allen Head Grub Screw before removing the Sleeve Spark Plug. Before fitting the Sleeve Spark Plug apply thin layer of molybdenum disulphite grease on the entry chamfers for the O rings for smooth sliding inside.
CO % Checking and Tune Up (To ensure betten mileage) : Do not apply liquid gasket at location (A) which may block the lubrication passage.
Check following before CO % checking / Tune up Air filter connections, intake manifold, insulator fitment, connecting tube fitment. Spark Plug gap (0.7 to 0.8 mm) All pipes and connections of fuel system for any cracks, leakage, plucking, pinching and loose connections. Ensure Tappet Clearance : Inlet : 0.05 mm Exhaust : 0.1 mm Ensure compression pressure inside the cylinder (6 to 10 Kg/cm2) Check the ignition timing (100 BTDC at 1500 rpm and 280 BTDC at 3500 rpm)
A
Valve timing Ensure the sprocket marks (A) are aligned horizontally with cylinder head top machined face and the piston is at TDC.
CO % checking and carburettor VC screw setting Start and warm up the engine The oil temperature should be above 600 C. This can be achieved by running vehicle in top gear at the speed of minimum 40 Kmph for 5 ~ 6 Kms. Adjust the engine speed to 1400 + 100 rpm with idling adjustment screw of carburettor. Adjust the CO with the VC screw. It should be in between 1.75 to 2.25 % Confirm the engine speed whether it is within 1400 + 100 rpm or not. When setting Idle CO %, idle rpm and VCS have to be adjusted together to achieve 2 % CO and 1400 + 100 engine rpm.
A A
Secure the Cam Chain Sprocket in the special tool firmly and then tighten the sprocket allen bolt (A). Ensure that the O mark on washer always faces outwards when tightening the allen bolt.
Item Make Identification No Type Idling Speed VC Screw Setting Main Jet Jet needle mark Needle jet mark Jet needle clip position 2 from top Pilot Jet Starter Jet Throttle valve Chock lever Fixed type Fixed type 17.5 922MP-1 4DHL42 117.5 2.5+2 turns out 1400+100 CV Type DJ - U3 Ucal-Mikuni BS 26
Pulsar 180cc
A
Inlet Rocker Arm Shaft is longer in length.
Rocker arm has 20 Rollers inside the outer cage. Doesn't have inner cage. Take utmost care while dismantling. Rollers should not fall inside engine. Apply grease for fixing needle rollers inside rocker arm.
While removing / refitting of piston pin circlip, cover the crankcase chamber with clean cotton cloth to avoid falling of circlip inside the engine.
Blow pressurised air to oil passages in reverse direction to that of oil flow. 2 stage with push pull type mechanism
49
50
Important Points to Remember
Important Points to Remember

Load the assly balancer idler gear with 2 teeths from either side using the special tool.
Belleville Washer
Plain Washer
Ensure While assembling hub clutch place plain washer first and then place belleville washer. Concave face should be upwards i.e. toward technician.
Clutch Hub
12
10
14
16
17
13
After placing Belleville, fit clutch plate with 48 friction material cubs (A) with more I.D. 4 Nos. of clutch plates with 36 friction material cubs (B) alternatively along with steel plates. Fit top clutch plate with 40 friction material cubs (C).
11
15
Take the Assembly Balancer Idler Gear along with Thrust Washer which is preloaded and is held in special tool, Slide down the special tool with Gear to engage the bottom half of the Assembly Balalncer Idler Gear with the Body Balancer Gear Assembly Fit Thrust washer on the other side. On assembly of Assembly Balancer Idler Gear the itched/Dot mark of ;Body Balancer Gear Assembly should match with the line mark on the Crankcase. Holding the Assembly Balancer Gear in special tool now slide inside the Clutch Housing so that the Clutch Housing smoothly engages with the top half of Assembly Balancer Idler Gear. Remove the special tool gently. Fit 2 dowels and Assly Balancer Idler Gear Cover Ensure perfect marking of gear marks with respect to crankcase mark.
Input shaft has special nut. Thick spacer washer tapered I.D. it should be placed on tapped portion of Input Shaft. Input Shaft has left hand threads.
When splitting crankcase always remove 1 long bolt fitted from clutch side first.
Remove long bolt immediately after removal of long bolt clutch side. Ensure proper fitment of bolt with copper washer to avoid oil leakage.
Shifter fork is having a roller. These roller are one side tappered inner dia. Taper portion of roller should face towards fork gear shift.
Ensure damper rubber fitment on magneto side guide plate.
Fit primary gear drive (A). The mark teeth of the primary gear should match with the line mark on the ccase. This indicated that the piston is at TDC position. This procedure should be carried before fitting the Clutch Housing & this position should not be disturbed while fitting the Clutch Housing.
51
52
Removal of Engine from Frame

Remove : 2 nuts (B) for silencer flange
Removal of Engine from Frame :
Remove :
Put OFF the fuel cock
Side panel LH
B
Note : Always remove the flange mounting first and then rear mounting to avoid misalignment of studs.
Side panel RH
Remove : Silencer assembly.
Remove : Bolt (A) of silencer bracket mounted on pillion RH side footstep.
Seat assembly by pulling the cable for seat lock release located on RH side. Disconnect the negative terminal of the battery. Disconnect the wiring harness socket for fuel level Indicator. Fuel pipe connections and moisture drain pipe from fuel tank. Disconnect stator plate harness Disconnect neutral switch coupler
Remove : Starter motor connection (A)
Remove : Drain bolt (A) and drain out the oil from engine. Refit the drain bolt with gasket & tighten it.
Recommended Oil Grade and Qty SAE 20W50 of API SG + JASO MA Drain & Refill 1000 ml. Engine Overhaul 1100 ml.
Grade
Quantity
Remove :
Bolt (A)
Remove : PCV pipe from breather
Petrol tank assembly.
Remove :
Bolts (A)
Gear shift pedal bolt (B)
Remove : Disconnect the reed switch coupler. Spark plug cap LH
Drive sprocket cover LH.
Using Special Tool : Sprocket Holder - 37 1030 53
Remove : Bolts (A) Plate drive sprocket Drive sprocket along with the chain. Neutral switch coupler (B).
Remove : Air filter mounting bolts to facilitate the removal of carburettor with reed switch. Clamps of carburettor and disconnect carburettor along with insulator and dismantle cables from it. Bracket bolts securing clutch cable on clutch cover. Spark plug cap RH
53
54

Engine Top End Dismantling :
Dismantling Engine
Remove :
While removing engine foundation bolts, first remove the topmost bolt
and then go down progressively.
Note : Bolts (A) holding the engine to the chassis. (4 bolts of 12 mm and 1 bolt needs deep socket for removing it).
Remove : Pull out the cover on the spark plug cap RH and the spark plug cap itself Using a plug spanner, loosen and remove the spark plug RH Loosen and unscrew the allen head grub screw of the sleeve spark plug
Note : Wrap a piece of cloth around the protruding edge of the sleeve spark plug and using a plier, pull out the sleeve.
Remove : There are 2 O rings fitted in the cylinder head, one on the cam chain wall and the other near the spark plug threading Using a thin, sharp pointed tool pierce the O rings and remove them. (If required)
Note : Remove these only if the O ring protrusim in the bore is non-existant (which means that the O ring has set and it has lost its compression or sealing ability.)
Lift up the engine off the chassis and place it on engine stand.
Remove : Loosen bolt (A) and unscrew chain tensioner plunger Cam chain tensioner assembly 2 bolts (B) Cam chain tensioner assembly A B Remove : Both tappet caps Magneto cover cap seal and rotate crankshaft to get piston at TDC. Ensure both tappets are at free state (i.e. at the end of compression stroke)
Note : After disconnecting all the sub assemblies and control cables from the engine lift up the engine and remove it from RHS of the vehicle.
Remove : 2 dummy plug 2 gaskets
55
56
Dismantling Engine
Remove : Piston pin lock LH & RH side
Dismantling Engine
Remove :
Cylinder head securing head cover 2 bolts (A)
Cylinder head securing head cover 4 bolts (B)
Cylinder head securing head cover 4 domed cap nuts (C)

Note : Place a piece of clean cloth above hallow portion of crankcase to arrest piston pin circlip if it falls during fitment.
4 copper plated steel washers
Note : Improper tightening sequence may cause warpage in cylinder head cover and it can be damaged permanently.
Remove :
Cylinder head cover complete
Cam shaft cap
Using Special Tool : Drift 74 9309 89 Remove : Remove piston pin Piston assembly
Using Special Tool : Sprocket Catcher - 3710 DH 36

Caution : When tapping the drift for removal of piston pin, confirm that the connecting rod is held firmly against the direction of tapping to avoid damage to big end bearing connecting rod of crankshaft.
Using Sp. Tool : Sprocket Catcher - 3710 DH 36
Remove : Remove : Block gasket 2 dowels (A) A

Sprcoket Catcher
Allen bolt
Spacer
Cam sprocket
Collar
Cam shaft assly
Note : Hold the cam chain up right using soft copper wire or thread. Do not use cotton waste for holding the cam chain.
Note : Tie the cam chain firmly using soft copper wire/thread firmly to avoid slipping down into crankcase.
Remove : A
Engine LH (Magneto Side) :

Remove : 5 bolts (A)
Cylinder head assembly
2 dowels
Gasket cylinder head
Remove :
Remove : Cover magneto.
Non tensioner side chain guide
Cylinder block assembly
57
58
Dismantling Engine
Rotor A 3 Screw (A) Guide starter assembly along with oil seal. Remove :
Dismantling Engine
Using Special Tool : Holder - H6 0721 00
Hold the rotor assembly
Remove :
Caution : Ensure that the woodruff key of rotor is removed prior to the removal of guide starter assembly. The lips of magneto oil seal housed in guide starter assembly will get damaged if not done so.
Rotor bolt (A)
Washer
Using Special Tool - Rotor Puller with butt pin : 37 10DJ 32 Remove : Kick starter bolt Kick starter
Engine RH : (Clutch Side)
Remove :
Rotor assembly
Woodruff key.
Remove : 1 screw - (A) Starter motor cover A
Note : Holding the gear complete starter clutch rotate the rotor and pull it out in Anticlockwise direction to prevent rollers and springs coming out. Rotor puller has left hand threads.
Warning : These components remain hot for a long time especially if removed from a hot engine. Wear suitable hand protection to prevent burns. Rotor puller has left hand threads
Remove : C B
Remove 12 Clutch cover bolts (B) Bracket clutch cable (C) Clutch cover
Note : The rod clutch lifter, plunger oil, plate plunger oil and spring joint may fall out of their respective places into the oil collection tray. If so, ensure that these are collected & accounted for before proceeding.
Gasket
Bolt (A)
Plate starter clutch gear return (B)
Gear starter clutch
Remove : B
Remove : 3 bolts (A) Oil pump assembly 2 Dowels Clutch cover gasket
A
Collar (A)
Shaft
Gear comp. starter counter assly
Starter Motor (B)

Warning : The oil pump may be hot, hence use suitable hand protection. Also, since the oil pump houses the oil strainer / mesh also, it may retain some quantity of oil. This oil may be hot. Hence proper care should be taken to drain it. Note : The oil which is in the oil pump housing should also be drained out into the oil drain tray for measuring drained oil.
59
60
Dismantling Engine
Remove : A Cover Washer 2 Dowel 3 Assly balancer Idler gear cover bolts (A)
Dismantling Engine
Using Special Tool : Primary Gear Holder 37 10DJ 28
Remove :
3 phillips head screws (A)
Centrifugal oil filter cover
Gasket
Warning : These parts may be hot, if removed from a hot engine. Use gloves for protection.
Remove : Clutch housing

Note : For ease in removal of clutch house insert special tool (P. No.-37 10DJ 63) in Assly Balancer Idler Gear.
Note : Some amount of oil is trapped in cover and body of centrifugal oil filter, this oil should be drained into the oil tray.
Using Special Tool :
Special Nut Puller 37 10DJ43 Remove : Assly Bal. idler gear 2 Washer
Primary Gear Holder 3710 DJ28
Remove :
Centrifugal oil filter special nut
Belleville washer
Body centrifugal oil filter assly

Remove : Bolt (A) Locking plate A Body balancer gear assly
Remove :
Bearing with plunger
Using Special Tool : Special Nut Puller 37 10DJ 43
Remove : Primary gear Square key
Primary Gear Holder 3710DJ28
Remove :
Input shaft special nut

Note : Take case that square key does not fall inside the crankcase hollow portion while removing.
Belleville washer
Clutch assly comp
Spacer Remove : Cam chain Cam chain sprocket Parallel Pin
Note : The existing Special Nut Puller 37 10DJ 43 can be used by grinding the tool OD to 25.9 + 0.1 mm
Dia. = 25.9+0.1
61
62
Dismantling Engine
Remove : Bolt (B) on LH side crankcase (Magneto side)
Dismantling Engine
Remove :
Gear change lever
Remove :
Remove : 8 bolts on LH side crankcase Split the Crankcase halves.
Spring
Allen bolt (A)
Guide gear
Note : Before separating crankcase halves confirm that all the crankcase joining bolts are removed and the sprocket cam drive with parallel pin on crankshaft assembly is removed.
Spacer
Parallel Pin
Note : Check and inspect the drum change arm stopper for free movement always.
Remove : Kick spring 2 Shafts (A) & (B) of gear shifter fork. 3 fork shifts (1 small for input 2 big for output shaft. 3 Rollers Drum change A
Using Kick starter lever
Remove :
Washer
Kick shaft assly comp
Note : Rotate the kick starter lever in Anticlockwise direction for removing the kick shaft assly.
Remove : The entire gear box assembly together
Remove :
Bolt (A)
Locking Plate
Kick idler gear
Remove : Crankcase gasket 2 dowels Crankshaft assly
Engine Central Part :
Remove :
Bolt (A) on RH side crankcase (Clutch side)
63
64
Dismantling - Engine Sub Assemblies

Remove : Bolt (A) Bearing stopper Using Special Tool : Bearing Driver Set - 37 10BA 61 A Remove: Bearing for gear drum from RH crankcase
Dismantling of Oil Seals and Bearings :
Crankcase Clutch Side :
Using Special Tool : Bearing Driver set - 37 1030 61
Remove :
Bearing (A) for input shaft assembly from crankcase RH
A C B A
Dismantling of Subassemblies :
Using Special Tool : Bearing Extractor - 37 10DJ 77
Remove:
E D
Bearing (B) for output shaft assembly from crankcase RH
Magneto Cover Remove : 2 Phillips head screws (A) of pulsar coil (E) mounting. Bolts (B) of stator assembly. 1 Phillips head screw (C) of stopper. Stator coil assembly (D) along with pulsar coil.
Cylinder Head Cover Using Sp. Tool Rocker Pin remover 37 10DH 35
A
Crankcase Magneto Side :

B
Remove :
Oil seal
Remove : Rocker shaft (A) Rocker arm Set of washers (1 wave and 2 plane) (B) Rollers 20 nos. (C)
Note : Similarly remove the other Rocker shaft & Rocker Arm from head over
A C
Remove :
Bearing (A) for output shaft assembly from crankcase LH

A B D C
Remove :
Top End :
Cylinder Head Using Sp. Tool Valve Spring Compressor 37 1031 07 & Adapter 37 10DJ 78 Remove :
F
Bearing (A) for body balancer gear bearing from crankcase LH
2 Cotter valve (A) Valve spring retainer (B)

E
Springs inner (D) Spring outer (C) Valve from below (E) Washer (F) Valve steam seal (G) Similarly carry out the same procedure to dismantle the other valve from the cylinder head assembly.
Remove :
Bearing (A) for input shaft assembly from crankcase LH
65
66

Bearing Removal from Assly Balancer Idler Gear Cover and Crankcase RH Using Sp. Tool : Bearing Extractor - 37 10CD 30 Remove : Needle roller bearing from RH crankcase.
Chain Tensioner Assembly Remove : Circlip (A) from the body (I) Cap (B) along with screw internal and screw external (C) Spring (D) Thrust washer (E) O' ring (F) Assembly Balancer Idler Gear
A C D
Bolt (G) and O ring (H) Remove : Thrust washers (A) Circlip (B) from any one side of the gear Scissor gear (C) Torsion Spring (D)
B E D CB A
Clutch Assembly
Remove :
4 bolts (A)
12
Holder clutch (B)
10
4 springs (C)
14
16
17
13
Clutch center (D)
11
15
Plain washer
Similarly carry out the same procedure on other side of the gear to dismantle the idler gear completely.
Bellivellie washer Gear Complete Starter Counter Assembly Place the gear comp. starter counter assly on the arbor press as shown in the figure. Using Bearing driver set (P. No. 37 1030 61) Remove : Needle roller bearing
Disc clutch friction (E) (Qty. 6 for 180cc / Qty. 5 for 150 cc)
Plate clutch (F)
Plate clutch pressure (G) (Wheel clutch)
Clutch housing
Thrust washer - conical from inner ID
Oil Pump
Remove : Input Shaft Assembly

B C EF I K
Clip (A)
Oil strainer element (B) with O ring (C)
1st gear is integral with the shaft (A) Remove thrust washer (B) and slide out gear 2nd drive (C) Remove gear 5th drive (D) and collect the splined washer (E) behind it. Remove circlip (F) and remove gear 3rd drive (G) Remove circlip (H) and collect the splined washer (I)
D G H J A
Kick Shaft Assembly
Remove :
Remove gear 4th (J) and collect the thrust washer (K) behind it.
L M H FE CB A
Thrust washer (A) Output Shaft Assembly There are no integral gears on output shaft. Remove thrust washer (A) and slide off the gear1st driven (B) and collect the steel bush (1st driven gear is mounted on steel bush (C) with shoulder ring Slide off the gear 4th driven (D). Remove circlip (E) and spline washer (F). Remove the gear 3rd driven (G). Collect the thrust washer (H) behind the 3 gear on output shaft (I)
JK N I G D
rd
Washer thrust (B)
Circlip (C) & thrust washer (D)
Spring kick starter ratchet (E)
Ratchet kick starter (F)
C D
Circlip (G)
Washer (H)
Pinion complete kick starter (I)
Remove circlip (J) and collect the washer (K) Remove gear 2nd driven (L) mounted on bush (N) with shoulder ring Slide out gear 5th driven (M)
67
68
Crankcase Magneto Side
Remove : 3 Screws (A) Guide starter assembly (B) on which oil seal is mounted. Oil seal (C) Damper (D)
Clutch Cover Remove : Parallel Pin (A) Clutch shaft release completely (B) by slightly rotating it so, Rack (C) Plunger oil (D) Plate plunger oil (E) Spring joint A (F) Oil filler plug (G) Oil seal kick shaft (H) Wire clip (I) Oil inspection window Flanged bolt (8 Nos.) (J) Set of damper (K) Set of plate (L) Grommet (M)
Camshaft Dismantling
Using Special Tool :
Bearing Pullers :
3710DJ 74 for Bearing 39227020
3710DJ75 for Bearing 39148520
Remove :
Bigger Bearing using sp. tool from camshaft assembly(A)
Collar de-comp (B)
Decompression unit (C)
Small Bearing (E)
Lock washer (D)
Parallel pin (F)
Gear Starter Clutch
Remove : Place the gear starter clutch on arbor press as shown in photo Using Bearing Driver Set (P. No.: 37 1030 61) Remove : Needle roller bearing
69
70
Parts Inspection Parameters
Spark Plug :
Type / Heat value - RG 4 HC/Bosh UR3DC (Resistive)
Gap between electrodes - 0.7 to 0.8 mm
Electrode condition - No errosion
Colour at the electrodes tip - Brownish
Threads of reach portion - Ok / No damage
Crankshaft : Big end axial/radial play : As per Service data. Runout : As per Service data. Threading condition : Ok / No damages. Key way condition : Ok / No damages. Big end bearing : Free rotation / Jam Con-rod : No bending / twisting Oil passage : No blockage. Square slot key way for primary gear Crankcase : Mating surface : Smooth / No scratches. No Cracks, damages, breakage. Bearing seat, oil seal seat & proper pressing / positioning of oil seals, needle roller, ball bearings freely rotating No Blow holes in casting Breather pipe / hole Oil passage : : Threads of holes & studs : No clogging Clean / No clogging Ok / No damages Visible number punching on LH Crank Case Bearings : Axial play Radial play Bearing Seat Bearing class & code Bearing Rotation : : : : : Ok / Not excessive Ok / Not excessive No sign of high spot on seating area. As per specification numbers Free Rotation
Cylinder Head : Mating surface : No warpage / No scratches (Service limit for warpage: 0.05mm) Identification mark - DJ mark embossed on casting No fins breakage Spark plug hole threads - Ok / No damage Carbon built up in combustion chamber cavity- Clean it Valve seat : No pitting / No carbon deposition Proper fitment of Dampers (4 Nos) Proper fitment of Orings Proper fitment of valve stem oil seals on valve guide Valve guide for crack if any Silencer mounting studs threads - Ok / No damage
Cylinder Block : No fins breakage No Scoring marks No Seizure marks Ok Seating mating surfaces Smooth Honing pattern Correct / Same grouping mark w.r.t. piston (A & B group) Inner diameter of block as mentioned in service data. Ovality - Not more then 0.05 mm. 3 Nos. of damper rubbers Properly fitted on fins Proper fitment of O ring on bottom side
Piston : Grouping mark with respect to cylinder block must be same. Diameter of the piston - As mentioned in service data No scoring marks on the skirt No blow by marks No seizure marks. Manufacturing / Identification code and date code Piston pin - scratches dent marks
Clutch : Clutch plates / Steel plates - Thickness as per service data Warpage as per service data No Seizure / Damaged bonding of friction material Tangs (Lugs) / Teeth - No wearing Thrust plate cracked No Foreign material embedded Colour change / Signs of overheating if any No uneven wear pattern Steel plates planishing Conical face machining for spacer clutch Clutch Housing : No Wear marks on slots. Clearance between clutch plate tangs and slot in the clutch housing should not be excessive Free movement of plates in clutch housing slots. Rivets of clutch housing should not be loose. Free rotation of housing on Input shaft
Rings : No uneven wear around circumference / breakage. Discoloration at working face. Carbon built up on inner face if any. Piston ring end gap - As per Service data Piston ring width (thickness) - As per Service data Free rotation of Rings in Piston grooves - No stickyness. Piton ring identification mark Top Ring : TOP 1, Second Ring : TOP 2
71
72

Guide Kick : No presence of any burr & flashes Face to face fitment on Crankcase after tightening. Application of loctite 638 to securing allen bolts
Clutch Hub / Clutch Wheel :
Contact surface for friction plates-should not be worn out excessively
Pressure Plate free movement in clutch hub splines
Holes for lubrication
Clutch hub height
Smoothness in ID of clutch wheel Camshaft : Presence of locating washer Free rotation of bearing Lobe height - as per Service Data No cut / wear marks on cam De-comp mechanism stickyness
Spacer free movement on clutch wheel
Presence of plain and wave washer in 1st clutch plate
Transmission :
No Teeth breakage or crack
No Wear pattern on teeth
No Wear of dog teeth & dog holes on gear
No Seizure mark on gear seat. Notes :
Free movement of gears on the shaft (1st Output, 2nd Output, 3rd Output, 4th Input and 5th input gears are free on the respective shaft)
Free movement of Fork shift on the fork shaft
Gear shift drum groove profile - Ok / No damage - Wear
Free movement of Fork shift guide roller in the drum groove
Drum :
Presence of Neutral rivet on the Drum
Free rotation of Drum in LH crankcase parent hole.
Inner hollow portion must be free from casting dust / burr
Groove profile width as per Service Data
Hole available for parallel pin
Drum profile free from Hi-Spot for free sliding of bush
Carburettor :
Float - No puncture - Alignment w.r.t float pin - Ok - Not touching to bowl walls
Needle Valve - No groove formation on the tip - Smooth action of spring loaded pin, - Smooth movement in its seat.
Volume Control Screw - Not bent / Threads OK. / Not jammed / Presence of Spring Washer and O ring.
Jets - Correct size, No wear of jet hole, No clogging
Piston Valve - Smooth free sliding, clearance in its seat, no excess wear mark.
Choke Operation - Smooth (Push and pull type)
73
74
Service Data - Engine

Rocker Arm Shaft Dia. Piston Diameter Piston / Cylinder Clearance
Service Data - Engine

Piston Ring / Groove Clearn.
Compression Pressure
Valve Clearance
7mm
Inlet Std. Limit 7.994 ~ 8.0 7.98 Serv. Limit Serv. Limit 63.488 ~ 63.498 Serv. Limit Std. Limit Std. Limit 63.478 ~ 63.488 0.012 ~ 0.030 Std. Limit Serv. Limit 0.05 0.05 0.15 0.10 Exhaust TOP 0.02~0.06 0.16 SECOND 0.01~0.05 0.15
Std. Limit
6.0 ~ 10.0 Kg/cm2
Std. Limit
Serv. Limit
5.0 ~ 10.0 Kg/cm
Serv. Limit
Cam Sprocket Diameter Valve Spring Free Length Piston Ring End Gap
Cam Height
Clutch Spring Free Length
Friction Plate Thickness
Std. Limit 31.0 30.4 Std. Limit 39.10 39.00 42.6 Serv. Limit 0.55 43.6 Serv. Limit 30.2 30.8 Std. Limit 0.15~0.30
61.48 ~ 61.36
Inlet Exhaust Inner Outer
TOP
SECOND 0.30~0.45 0.70
Std. Limit Serv. Limit
30.0 29.0
2.9 ~ 3.1 2.75
Std. Limit
Serv. Limit
61.30
Serv. Limit
Valve Stem Diameter
Valve Stem Bend
Valve Head Thickness
Pressure Plate Warp
Shift Fork Guide Pin Dia.
Shift Drum Groove Width
Inlet TIR 0.01 Std. Limit 0.5 0.3 0.6 TIR 0.03 Serv. Limit 0.8
Exhaust
Std. Limit
Inlet
Exhaust
0.2 0.3
4.4 4.2
7.15 7.0
Std. Limit
4.48
4.46
Serv. Limit
4.40
4.41
Serv. Limit
Cylinder Head Warp
Camshaft Chain Lth. 20 Links Cylinder Inside Diameter
Crankshaft Run Out
20-link length
10mm 20mm 40mm
1st
2nd
21st
MEASURE THIS LENGTH
Std. Limit 127.00 ~ 127.20 128.0
63.50 ~ 63.508 63.508 ~ 63.515
0.02 Max. 0.05
Serv. Limit
0.05
Serv. Limit
75
76
Service Data - Frame

Front Brake Pad Thickness Front Fork Oil Front Fork Spring Free Length
Service Data - Frame
Brake Panel Cam Hole Dia.
Brake Cam Diameter
Fork Oil Level 218 + 2.0 mm.
Free Length
Grade : SAE 10W20

11.95 ~ 11.98 398.50 391.00 11.88 Serv. Limit 3.8 Serv. Limit Std. Limit 7.4 Std. Limit
Std. Limit
12.00 ~ 12.03
Std. Limit
Quantity :165 ml / Fork Pipe (Drain & Refill)
Serv. Limit
12.15
Serv. Limit
Brake Shoe Lining Thickness Notes :
Brake Drum Inside Diameter
Axle Run Out
100 mm
Std. Limit 130 .0 ~ 130.16 130.75 Serv. Limit TIR 0.2 TIR 0.1 or Less
3.85 ~ 4.15
Std. Limit
Std. Limit
Serv. Limit
2.0
Serv. Limit
Axial Wheel Run Out
Radial Wheel Run Out
Drive Chain Slack
Std. Limit TIR 0.8 or Less TIR 2.0 Serv. Limit 40 ~ 50 25 ~ 35
TIR 1.0 or Less
Std. Limit
Std. Limit
Serv. Limit
TIR 2.0
Serv. Limit
Drive Chain Length
Rear Sprocket Warp
Tyre Tread Depth
20-link length
1st 2nd
21st
MEASURE THIS LENGTH
Std. Limit 0.4 or Less 0.5
254.0 ~ 254.6
Std. Limit
Front: 5.0 Rear: 6.8 Front: 1.0 Rear: 1.5
Serv. Limit
259.0
Serv. Limit
77
78
Parts Identification
UG-III
Part Name Shaft Input Transmission DH 1015 19 Part No. Description
Parts Identification - Engine UG-II
Parts Identification - Engine
Part Name Shaft Input Transmission DK 1011 25 Better clamping of clutch assly is ensured on Input Shaft for effective torque transmission with this new clutch mechanism. Taper provided on shaft near clutch mounting end. Identification Mark
Part No.
Description
Effective clamping of clutch assembly is ensured on Input Shaft by using guide plate clutch in between shaft & clutch assembly. No Taper provided on shaft near clutch mounting end. Guide Gear Shift DJ 1011 48 Guide Gear with 4 pins is meshed with gear change lever & transmits reciprocating motion into rotary motion & thus rotates drum change. Guide Gear is having 4 pins.
Identification Mark
Part Name Guide Gear Shift DK 1011 58 Guide Gear with 6 pins is meshed with gear change lever & transmits reciprocating motion into rotary motion & thus rotates drum change. Description Guide Gear is having 6 pins. Part No.
Part Name
Part No.
Description
Identification Mark
Identification Mark
Part Name Fork Gear Shift (Input & Output) Input : DK 1011 33 Output : DK 1011 34
Part Name Part No.
Fork Gear Shift (Input & Output) DH 1011 30 - Input DH 1011 32 - Output
Part No.
Description
The roller in fork gear shift roll in the drum profile smoothly as & when drum rotates & guides to transmit To & Fro motion to fork gear shift for matching respective gears.
Description
4 4.
Pin diameter is 4.4 mm U mark on fork shift.
5 mm
Identification Mark
The fork gear shift pin slides in the drum profile as & when drum rotates & guides to transmit To & Fro motion to fork gear shift for matching respective gear. Pin dia. = 5 mm. I/P shaft fork mark = S 32. O/P shaft fork mark = S 95 & S 92 respectively. Part Name Gear Drum Change Assembly
Identification Mark
Part Name Gear Drum Change Assembly DK 1011 32 It has a wide profile (groove) for smooth rolling of fork gear shift roller in drum profile for smooth shifting of gear. Profile width is 7.15 mm. It has a square window parallel to neutral stopper locater. Lever Comp Gear Shift DH 1017 05 Lever comp. gear shift is meshed with guide gear shift constantly. Thus helps in transmitting reciprocating motion to guide gear. Selector lever operates radially. Selector lever is short in length.
Part No.
5 mm
Part No. Description
DJ 1011 46 It has a wide profile (groove) for smooth sliding of fork gear shift pin in drum profile for shifting of gears. Identification Mark Profile width is 5 mm. It has a odd shape window parallel to neutral stopper locater. Part Name Part No. Description Lever Comp Gear Shift DH 1011 34 Lever comp. gear shift is meshed with guide gear shift constantly. Thus helps in transmitting reciprocating motion to guide gear. Identification Mark Selector lever operates To & Fro. Selector lever is more in length.
7.15 mm
Description
Identification Mark
Part Name
Part No.
Description
Identification Mark
79
80
UG-III
Part Name Clutch Cover DH 1011 49 It houses the entire clutch side assemblies. Part No. Description
Part Name Clutch Cover DJ 1012 41 It houses the entrire clutch side assemblies.
Part No.
Description
Identification Mark
Clutch cover has Engine oil inspection window. Identification Mark
Clutch cover does not have Engine oil inspection window. Holder Clutch (Thrust Plate) DH 1014 84
Part Name Holder Clutch (Thrust Plate) DK 1010 78 Holder clutch holds the clutch bearing & plunger. Description Part No.
Part Name
Part No.
Description
Holder clutch holds the clutch bearing & plunger.
Identification Mark Holder clutch has 4 holes for mounting.
Identification Mark
Holder clutch has 6 holes for mounting.
Part Name Clutch Spring DH 1017 43
Part Name Part No.
Clutch Spring DH 1014 83
Part No.
Description
Clutch spring helps smooth engaging & disengaging the clutch mechanism. Clutch spring height is 30.8 mm.
Description
Clutch spring helps smooth engaging & disengaging the clutch mechanism. Identification Mark Clutch spring height is 29.3 mm.
Identification Mark
Part Name Clutch Center DK 1010 01
Part Name Part No.
Clutch Center DJ 1011 79
Part No. Clutch center holds the set of clutch plate & pressure plate. Step for spacer is provided. Clutch center height is 26 mm. Clutch Wheel DK 1011 63 Clutch wheel holds the set of clutch plate & pressure plate. Clutch wheel has 4 legs for mounting clutch springs.
H
Description Clutch center holds the set of clutch plate & pressure plate.
Description
26 mm
Identification Mark
30 mm
Identification Mark
No step for guide plate provided. Clutch center height is 30 mm. Part Name Part No. Description Clutch Wheel DH 1013 44 Clutch wheel holds the set of clutch plate & pressure plate. Identification Mark Clutch wheel has 6 legs for mounting clutch springs.
Part Name
Part No.
Description
Identification Mark
81
82
UG-III
Part Name NA NA NA Part No. Description
Part Name Clutch Plain Washer 39 2161 11 New part added for preventing clutch judder.
Part No.
Description
Identification Mark Plain washer with no Identification Mark. NA
Identification Mark
Part Name Clutch Belleville Washer 39 2167 12 Description Part No.
Part Name
NA NA
Part No.
Description New part added for preventing clutch judder.
NA
Identification Mark Clutch Belleville Washer is concave in shape.
Identification Mark
NA
Part Name Disc Clutch Friction Plate DK 1011 49
Part Name Part No.
NA NA
Part No.
Description
Clutch plate ID is smaller than regular clutch plate because to accommodate the plain washer & wave washer of anti judder mechanism. This plate is fitted facing the clutch hub side.
Description
NA
Identification Mark
Internal diameter is 109.5 mm. Friction material cubs are 48 nos. Clutch Plate Pressure DK 1011 63 New part added. This plate is fitted facing the clutch wheel side. Friction material cubs = 40 nos. Clutch plate appears to be in Brownish colour. Clutch Plate (4 Nos.) DK 1011 51 New part added. 4 clutch plates of same specifications are sandwiched in between LH & RH clutch plates for torque transmission. Friction material cubs 36 nos. Clutch plate appears to be in Greenish colour.
Identification Mark
NA
Part Name
Part Name Part No. Description
Clutch Plate Pressure (6 Clutch Plates) DH 1013 44 Total 6 clutch plates of same specifications are housed in clutch assembly for torque transmission. Identification Mark All clutch plates are Brown in colour.
Part No.
Description
Identification Mark
Part Name
NA NA NA
Part No.
Description
Identification Mark
Identification Mark
NA
83
84
UG-III
Part Name Part No. DH 1015 57 Description
Part Name Plate Clutch (Pressure Plate) DK 1011 63 Pressure plate are housed in between clutch plates.
Plate Clutch (Pressure Plate)
Part No.
Description
Pressure plate are housed in between clutch plates.
Identification Mark
Pressure plate is more wide. Pressure plate width = 17 mm. Identification Mark Spacer DK 1011 26 New part added for adding is better face clamping of clutch assembly on Input Shaft. Internal diameter (ID) is in conical shape. Description Part No. Part Name
Pressure plate is not wide as compared with regular. Width = 14 mm. Guide Plate Clutch DH 1013 74 Guide plate clutch helps in better clamping of clutch assly. on Input shaft. Guide Plate clutch has a stainless steel finish with internal splines.
Part Name
Part No.
ID
Description
Identification Mark
Identification Mark
Part Name Clutch Housing DK 1010 74
Part Name Part No.
Clutch Housing DH 1015 58
Part No.
Description
Clutch housing holds the entire clutch assembly & the slots helps for effective lubrication. Slots provided in clutch housing.
Description
Clutch housing holds the entire clutch assembly.
Identification Mark
Identification Mark
No slots in clutch housing.
Part Name Head Cover Cylinder head cover is a part of Cylinder Head Comp Head cover houses the complete OHC system.
Head Cover Cylinder head cover is a part of Cylinder Head Comp Head cover houses the complete OHC system.
Part No.
Description
Identification Mark U mark embossed in casting.
Identification Mark
DJ mark embossed in casting.
Part Name Cylinder Head Comp DJ 1012 69
Cylinder Head Comp DH 1016 00 Cylinder head comp houses the complete OHC system with valve train. Identification Mark DJ mark embossed in casting. Valve springs fitment groove is not deep.
Part No.
Description
Cylinder head comp houses the complete OHC system with valve train. DJ mark along with U mark embossed in casting. Valve springs fitment groove is deep.
Identification Mark
85
86
UG-III
Part Name Camshaft Assembly DH 1016 17 Part No.
Part Name Camshaft Assembly DH 1017 03
Part No.
Description
Camshaft assly is housed in between cylinder head cover & cyl. head comp. It drives the entire valve train assly as per enhanced valve timing. Description Cam (track) width is less. Track width = 9.6 mm.
Camshaft assly is housed in between cylinder head cover & cyl. head comp. It drives the entire valve train assly. Cam (track) width is more. Track width = 12.6 mm.
9.6 mm
Identification Mark
Identification Mark
12.6 mm
Part Name Valve Spring Outer DH 1017 30 Valve spring helps in smooth closing of valves without any noise as per enhanced valve timing. It is more in length. Length = 43.6 mm. Spring is marked with White oil paint. Valve Spring Inner DH 1017 31 Description Part No.
Part Name
Valve Spring Outer DS 1011 11 Valve spring helps in smooth closing of valves without any noise. It is short in length. Length = 42 mm. Spring is marked with Blue oil paint.
Part No.
Description
Identification Mark
Identification Mark
Part Name
Part Name Part No.
Valve Spring Inner DS 1011 10
Part No.
Description
Valve spring helps in smooth closing of valves without any noise as per enhanced valve timing. It is more in length. Length = 39.1 mm. Spring is marked with White oil paint. Stator Plate DJ 1110 21 All Electrical coils like Pick-up, Exciter, Lighting, Battery charging coils with enhanced ignition timing values are fitted on this plate. Stator plate harness neutral coupler is having square shape. Magneto Assembly (Rotor) DJ 1110 20 Magneto assembly rotor is having analog ignition timing for initial starting for avoiding back kicking. UG-3 mark embossed on the body viewed from tail side.
Description
Valve spring helps in smooth closing of valves without any noise. Identification Mark It is short in length. Length = 38 mm. Spring is marked with Blue oil paint. Part Name Part No. Description Stator Plate DJ 1110 04 All Electrical coils like Pick-up, Exciter, Lighting, Battery charging coils are fitted on this plate. Identification Mark Stator plate harness neutral coupler is having bullet type terminal. Part Name Part No. Description Magneto Assembly (Rotor) DJ 1110 57 Magneto assly rotor is having only Digital Ignition Timing. Identification Mark E & M mark embossed on the body viewed from tail side.
Identification Mark
Part Name
Part No.
Description
Identification Mark
Part Name
Part No.
Description
Identification Mark
87
88
UG-III
Part Name Centrifugal Oil Filter DH 1010 64 Part No.
Part Name Centrifugal Oil Filter DH 1010 64
Part No.
Description
The centrifugal oil filter body wall thickness has been increased by reducing the internal diameter for getting better strength. Description The centrifugal oil filter has a cut mark on tail end. Identification Mark
The centrifugal oil filter body internal diameter is more as compared to UG-III filter. The centrifugal oil filter does not have cut mark on tail end.
Identification Mark
89
90
UG-III
Part Name Carburettor Assembly DJ 1210 20 Part No.
Parts Identification - Chassis UG-II
Parts Identification - Chassis
Part Name Carburettor Assembly DJ 1012 32
Part No.
Description
With enhanced valve timing & to achieve better engine performance the carburettor assembly is retuned. Description On RH side of Carburettor body BS-29, DJ-U3 mark is embossed. Identification Mark Air Filter Assembly DJ 1210 40 The new large volume air filter with fine & corse filter foam is incorporated to provide torque on demand with optimised intake system. Description Drain tube is provided on bottom side to discharge the condensed engine oil. Silencer Assembly DJ 1012 43 Part No. Part Name
To meet the requirement of UG-II engine specifications the carburettor is tuned.
Identification Mark
On RH side of Carburettor body BS-29, DJ-U2 mark is embossed. Air Filter Assembly DJ 1211 05 A large volume air filter is introduced to provide torque on demand with optimised intake system. No drain tube is provided on bottom side to discharge the condensed eng. oil.
Part Name
Part No.
Description
Drain Tube
Identification Mark
Identification Mark
Part Name
Part Name Part No.
Silencer Assembly DJ 1011 61
Part No.
Description
The silencer has been further optimised to match the changes done incorporating the new camshaft & air filter assembly. Flanged bolt on ExhausTEC is facing on LH side.
Description
The silencer has been optimised to meet the performance of Pulsar UG-II with ExhausTEC introduction. Identification Mark Flanged bolt on ExhausTEC for measuring CO% is facing perpendicular to steering. Part Name Part No. Description Head Light Assembly DJ 2011 04 The parking lamps are in line with the head light body line. Identification Mark Parking lamps are inline with head light body. No provision for mask fitment. Part Name Part No. Description Handle Holder Assembly DJ 1810 38 Handle holder assembly height is been designed low to accommodate twin pod speedo console.
Identification Mark
Part Name Head Light Assembly DJ 2011 32

The parking lamps are projected out with a new aggressive look & together with the mask that gives a real Phantom look. H/L facing has been lowered to give balanced looks.
Part No.
Description
Identification Mark
Parking lamps are projected out. Provision for mask fitment. Handle Holder Assembly DH 1810 53 Handle holder assembly height has been increased to accommodate new speedo console. Height of handle holder is more i.e. 31.5 mm.
Part Name
Part No.
Description
Identification Mark
Identification Mark
Height of handle holder is less i.e. 18.5 mm.
91
92
UG-III
Part Name Holder Fork Upper DJ 1810 17 Part No.
Part Name Holder Fork Upper DH 1810 56
Part No.
Description
Holder fork upper cover clamps the fork pipes & handle holder. Description No bracket for holding speedo console. Identification Mark
Holder fork upper cover clamps the fork pipes, handle holder & twin pod speedometer assembly. To mount the twin pod speedo console there is a bracket provided. Brace Fender DH 1612 58 Brace fender gives reinforcement to mud guard & also guides the brake hose going towards caliper assembly. No bracket provided for disc brake hose / speedo cable.
Identification Mark
Part Name Brace Fender DH 1613 04 Brace fender gives reinforcement to mud guard & also guides the wire / hose going to wheel sensor & caliper assembly respectively. Description 2 nos. of brackets provided for a) Speedometer wire. b) For disc brake hose. Front Number Plate Bracket DH 1612 92 Part No.
Part Name
Part No.
Description
Identification Mark
Identification Mark
Part Name
Part Name Part No.
Front Number Plate Bracket DJ 1811 11
Part No.
Description
The front number plate bracket holds the number plate & for firm fitment 3 point mounting is given. 3 holes for mounting on lower T. 1 hole is oblong. Speedometer Assembly DJ 2011 44
Easy to read digital speedometer displaying speed in kmph, odometer displaying distance covered & trip meter displaying distance covered per trip with resetting facility.
Description
The front number plate bracket holds the number plate & is mounted with 2 point mounting. Identification Mark 2 holes for mounting on lower T.
Identification Mark
Part Name
Speedometer Assembly DJ 1910 48 Twin pod analogue type speedometer displaying vehicle speed, engine rpm, odometer & trip meter. With trip meter adjustment facility. Identification Mark Twin pod analogue type speedometer.
Part No.
Description
Identification Mark Digital speedometer with analogue type tachometer.
Part Name Wheel Sensor Unit DK 1011 63
Case Meter DJ 1510 57 Case meter assly houses the speedometer worm gear & the pinion gear assly to drive speedometer. Identification Mark Provision for mounting pinion gear & speedometer gear.
Part No.
Description
New part added. It is a sensor sensing the vehicle speed and is a non contact type wheel sensor. NIL
Identification Mark
93
94
UG-III
Part Name Control Switch LH DJ 2010 24 Part No.
Part Name Control Switch LH DH 2010 48
Part No.
Description
The switches operate without any physical contact & thus has no wear & tear of parts. Also these have illumination of tell-tale icons through LED's which glows Bluish-White during night driving. Description Coupler colour is White. Identification Mark
These are conventional switches & operate on physical make & brake mechanism causing more wear & tear of parts. Coupler colour is Red.
Identification Mark
Part Name Control Switch RH DH 2010 49 Part No.
Part Name
Control Switch RH DJ 2010 12
Part No.
Description
The switches operate without any physical contact & thus has no wear & tear of parts. Also these have illumination of tell-tale icons through LED's which glows Bluish-White during night driving. Description Provision of engine kill switch.
These are conventional switches & operate on physical make & brake type mechanism causing more wear & tear of parts. No engine kill switch available.
Identification Mark
Identification Mark
Part Name Battery DJ 2011 25
Part Name Part No.
Battery DJ 2010 36
Part No.
Description
A low maintenance battery with a unique vent mechanism that allows only gas / vapours to escape & not the electrolyte. Hence electrolyte level inspection interval is less. Battery top side mould has orange colour. Battery has vent valve on RH side. CDI Unit DJ 1110 23
Description
Conventional type of battery with overflow tube mechanism. Electrolyte level inspection interval is more as compared to low maintenance battery. Identification Mark Battery top side mould has black colour. Battery have a vent plug on RH side. Part Name Part No. Description CDI Unit DJ 1110 17
Identification Mark
Part Name
Part No.
Description
For easy kick starting the ignition timing has been optimised by introducing analogue signaling to CDI unit till 3000 rpm & thereafter digital signaling. Two green colour dot marks on CDI unit.
CDI unit has only digital signaling.
Identification Mark
Identification Mark
One green colour dot marks on CDI unit.
Part Name Side Stand Switch DH 2010 55
Side Stand Switch DJ 2011 05 NIL
Part No.
Description
Side stand switch assembly coupler mounting position shifted hence cable is longer in length. Side stand switch cable length is more.
Identification Mark
Identification Mark
Side stand switch cable length is less.
95
96
UG-III
Part Name Side Stand Magnet Part No. NIL Description NIL
Part Name Side Stand Magnet
Part No.
Description
Identification Mark Side stand magnet body has green passivation.
Identification Mark
Side stand magnet body is black in colour.
Part Name Seat Assembly DJ 2110 03 For proper locking & proper fitment of tool kit the seat assembly is redesigned. Description Part No.
Part Name
Seat Assembly DJ 2110 01 NIL
Part No.
Description
Identification Mark
No rib at tool kit mounting area. Seat locking stud is located at extreme tail end. Seat Lock Assembly DJ 2110 06
Identification Mark
Rib at tool kit mounting area. Seat locking stud is located in central part of seat assly. Part Name Part No. Seat Lock Assembly DH 1610 46
Part Name
Part No.
Description Since seat lock is shifted to tail end of the seat.
Description
The seat lock is located at center of the seat.
Identification Mark Seat lock cable length is more.
Identification Mark
Seat lock cable length is short as compared to UG-III cable. Part Name Part No. Description Gear Change Pedal DH 1011 49 NIL
Part Name Gear Change Pedal DJ 1011 49 The gear change pedal has more curved shape for proper placing of foot & to avoid foot fouling with step holder. Gear pedal has more curved shape.
Part No.
Description
Identification Mark
Identification Mark
Gear pedal has less curved shape.
Part Name Holder RH Step & LH Step DJ 1612 57 & DJ 1612 56
Holder RH Step & LH Step DJ 1611 12 & DJ 1611 11 Holder step provided for resting pillion rider's foot.
Part No.
Description
Holder step provided for resting pillion rider's foot.
Identification Mark
Additional projected step is provided for better aesthetic look.
Identification Mark
No additional projected step is provided.
97
98
UG-III
Part Name Rear Fender DJ 1610 51 Part No. Description
Part Name Rear Fender DJ 1612 54 The rear fender is located below the rider seat for arresting dust / dirt & water splashing on. On rear fender a step is provided at rear end RH side. Identification Mark Saree Guard DH 1612 94 Saree guard is mounted on chassis as a safety feature for arresting the possibility of saree getting entangled into rear wheel while riding the bike. Description Saree guard has a less curve shape near ladies foot step as compared to UG-II. Saree guard mounting allen bolt is short in length. Part No. Part Name
Part No.
Description
The rear fender is located below the rider seat for arresting dust / dirt & washer splashing on. On rear fender no step is provided.
Identification Mark
Part Name
Saree Guard DJ 1612 15 Saree guard is mounted on chassis as a safety feature for arresting the possibility of saree getting entangled into rear wheel while riding the bike. Saree guard has more curve shape near ladies foot step as compared with Pulsar UG-III. Saree guard mounting allen bolt is more in length.
Part No.
Description
Identification Mark
Identification Mark
99
100
Tightening Torque - Engine

Cylinder Head Cover Nuts Front Axle Nut Rear Axle Nut Torque Rod Nut
Tightening Torque - Frame
Clutch Nut (LH Threads)
Cylinder Head Cover Bolts
5.0 Kg.m
3.5 Kg.m
1.0 ~ 1.5 Kg.m
4.0 ~ 5.0 Kg.m
8.0 ~ 10.0 Kg.m
3.0 ~ 4.0 Kg.m
Camshaft Sprocket Allen Bolt Rotor Mounting Bolt
Starter Motor Mounting Bolts
Sleeve Nut
Rear Sprocket Mtg. Nut
Handle Bar Holder Bolts
1.4 Kg.m (Loctite 243) 4.5 Kg.m
1.1 Kg.m
7.0 ~ 8.0 Kg.m
1.8 ~ 2.5 Kg.m (Loctite 243)
2.0 ~ 2.2 Kg.m
Kick Guide Allen Bolts
Spark Plugs (2 Nos.)
Drain Bolt
Steering Top Cap Bolt
Stg. Stem Nut (slotted)
Upper Clamp Allen Bolt
1.2 Kg.m 2.5 Kg.m
1.4 Kg.m
3.5 Kg.m
0.5 Kg.m
1.8 ~ 2.0 Kg.m
Lower Clamp Bolt
RSA Mounting Dome Nut
Swing Arm Pivot Nut
2.5 ~ 3.5 Kg.m
3.5 ~ 4.0 Kg.m
8.0 ~ 10.0 Kg.m
Caliper Install Bolts
Brake Disc Allen Bolts
Banjo Bolt Caliper
2.2 ~ 2.8 Kg.m
0.9 ~ 1.1 (Loctite 243)
2.2 ~ 2.8 Kg.m
103
104
Assembly - Engine
Fit : Oil seal for Output Shaft
Assembly - Engine
Fitting of Oil Seals and Bearings :
Crankcase RH (Clutch Side) Use Bearing Driver set (P. No. 37 1030 61) Fit : Bearing for Input Shaft Assembly
Use Bearing Driver set (P. No. 37 1030 61) Fit :
Fit : Oil seal for Gear Changer Lever
Bearing for Output Shaft Assembly
Crankcase LH (Magneto Side)
Clutch Cover Fit : Oil seal for Kick Shaft Assembly
Use Bearing Driver set (P. No. 37 1030 61)
Fit :
Bearing for Output Shaft
Fit : Oil seal for Clutch Lever on Clutch Cover
Bearing for Input Shaft
Note : Do not use inner guide while fitting the bearing for Input Shaft in Crankcase LH as this will damage the protruding lug of crankcase casting. Shield of brg. must be on crankcase side/protruding lug side.
Assembly of Sub assemblies :

Magneto Cover Fit : Harness in the Cover Stopper and tighten the Screw (Use Loctite 243) Pulsar Coil and tighten 2 Screws (Use Loctite 243) Stator Assembly and tighten 2 Bolts (Use Loctite 243) 2 Dowel Pins
Bearing for Body Balancer gear Assembly

C B A D E
Oil seal on Guide Starter Assembly
O ring on Guide Starter Assembly.
Damper
Camshaft Assembly Fit : Parallel Pin (A) De-compression Mechanism (B) Washer (C) Washer (D)
105
106
Assembly - Engine
Assembly - Engine
Similarly carry out the same procedure to assemble the other Valve in the Cylinder Head. Note : Ensure that there is no valve leakage. If required pour the petrol in intake and Exhaust manifold and observe leakage at valve head.
Using Arbour Press Fit : Bigger Bearing (E) Small Bearing (F)
Note : Apply thin layer of oil on sliding surfaces of parts for smooth fitting.
Head Cover
A B C D E F I H G
Chain Tensioner Assembly Fit : O ring (F) in the body (I) Thrust Washer (E) Spring (D) Cap (B) along with Screw Internal and Screw External (C) (Keep the Spring and Screw Terminal fully compressed inside) Circlip (A) Clutch Assembly
Fit :
Roller rocker arm
Tappet Screw
Tappet Nut
20 Rollers in cage outer
2 7 4 6 7 6 7 12 10 8
Note : There are 2 cages in roller rocker arm each cage holds 20 rollers Inner cage in Absent Multipurpose grease is to be applied in outer cage to hold the roller firmly while assembling
6
Assemble the clutch plates and friction plates in clutch center / clutch hub. Fit : Plain Washer in Clutch Center / Clutch Hub Bellivelli Washer
Assembling Head Cover

5 1 14 6 3 17 11 15 16 13 9
Fit :
Roller Rocker Arm
Set of Plan and Wave Washer
Clutch Plate(A) 1 Nos Pressure Plate 5 Nos Clutch Plate (B) 4 Nos Clutch Plate (C) 1 Nos Wheel Clutch Springs 4 Nos. Thrust Plate Bolt Using Special Tool T1011168 Align the clutch assly into the clutch housing. Fit : Spacer Clutch Assly
Rocker arm shaft
Gaskets
Dummy Plugs
Note : Repeat the same procedure for fitment of other roller rocker arm
Cylinder Head
Fit :
Valve steam seals
Slide the Valve from below.
Place the Valve Springs (C&D) (Inner and outer closed coiled ends placed at the bottom side)
Valve Spring Retainer (B)

Note : Ensure concentrity of Thrust Plate w.r.to Clutch Wheel, Clutch Center, Clutch Housing. Using Special Tool The Special Tool can also helps in preventing the cracking / Bending of Thrust Plate while removing and refilling the thrust plate.
Using the sp. tool Valve Spring Compressor 37 1031 07 & Adaptor 37 10DJ 78
Press the valve springs
Fit the cotter valves (A) & release the special tool
107
108
Assembly - Engine
Loading the assembly Balancer Idler Gear Using Special Tool - Balancer Gear Holder 37 10DJ 63 Slide the Assembly Balancer Idler Gear in special tool (A) Rotate the Scissor Gear anticlockwise till the lug contacts the torsion spring.
Assembly - Engine
Oil Pump Fit : O ring (A) on the Oil Strainer (B) Clip (C)
Using a marker, mark the Balancer Idler Gear and Scissor Gear Tooth Using Special Tool Turn the Scissor Gear anticlockwise such that 2 teeth pre-load is achieved. This can be confirmed by the markings done previously. Holding the Scissor Gear pre-loaded in the above position slide the Scissor Gear into the special tool completely. Repeat the same procedure for loading the other Scissor Gear.
Note : Keep this Assembly balancer idler gear in loaded condition with special tool.
Kick Shaft Assembly Fit : Pinion Complete Kick Starter (I) Washer (H) Circlip (G) Ratchet Kick Starter (F)
C D
Note : Match the dot mark of Ratchet Kick Start with respect to Spindle Kick Start Assembly and then slide Ratchet Kick Starter (F) on Spindle Kick Start
Gear Complete Starter Counter Assembly Using Arbour Press Fit : Needle Roller Bearing
Spring Kick Starter Ratchet (E) Washer Thrust (D) Circlip (C) Washer Thrust (B) Thrust Washer (A)
Assembly Balancer Idler Gear Bearing Using Bearing Driver set (P. No.: 37 1030 61) Fit : Needle roller bearings in crankcase RH and Cover Crankcase LH (Magneto Side) Fit : Guide Starter Assembly 3 Screws (A) (Use loctite 243) A
Note : Apply oil on bearing OD before pressing bearings for smooth bearing
Fit : Springs (D) Scissor Gears (C) Circlip (B) Thrust washer Similarly carry out the same procedure on other side of the gear to assemble the Balancer Idler Gear completely.
A B
CB A
H
Note : Ensure that one spring end butts against spring dowel in Balancer Idler Gear & the other end of spring should butt against the lug on Scissor Gear
K J L
D F E
Clutch Cover Fit : Kick shaft oil seal (H) Oil inspection window Wire clip (I) Set dampers (K) Set of plates (L) Bolts (J) Rack (C) Shaft Clutch Release (B) in Clutch Cover by rotating it slightly to match the teeth. Parallel Pin (A) to lock the Shaft Clutch Release Washer
109
110
Assembly - Engine
Engine Assembling
Engine Central Part Fit : (In Magneto side Crankcase) Input and Output Shaft Assembly simultaneously.
Assembly - Engine
Spring torsion clutch lever External lever Bolt Spring joint A (F) Plunger Plate (E) Plunger oil (D) 2 Dowel Pins Grommet (M) Oil feeler plug (G) Apply loctite 243 to all damper fitment bolts.
Fork shifts along with rollers on Input and Output Shaft Assembly (2 bigger fork shifts on output shaft and 1 smaller on input shaft).
Note : For ease of assembly of gears, remove gear 1st driven and insert both the input and output shaft assemblies with gears in mesh into their respective bearings. The gear box should be in neutral gear before RH Crankcase is assembled on to LH Crankcase.
Note : Ensure fitment of set of dampers and plate before fitting the above.
Fit : Drum Change Shaft Gear Shift Kick Spring (A) 2 Dowels Gasket
Input Shaft Assembly
B C
EF
Fit : From LH side of shaft (A)
Thrust washer (K)
Gear 4th (J)
Splined washer (I)
Circlip (H)
Gear 3rd drive (G)
G H
Circlip (F)
Splined washer (E)
Gear 5th drive (D)
Caution : Use a sharp blade or knife to cut off any protruding Gasket. This is very important for preventing any oil leakage from Crankcase and Cylinder Block Joint. Don't apply grease / any adhesive to Crankcase Gasket as these Gasket when comes in contact with oil expands and seals hidden cavities.
Gear 2nd drive (C) Fit : Crankshaft
Thrust washer (B)
FE
CB
Output Shaft Assembly

Caution : Check oil supply to big end bearing by pumping oil in the clutch side end of crankshaft and lets oil dribble out of con-rod big end sides.
Fit : from LH side of shaft
Gear 5th driven (M)
Bush (N) with shoulder ring
Gear 2 driven (L) Fit : Crankcase RH

rd
nd
washer (K)
Circlip (J)
Fit : from RH side of shaft
JK
Thrust washer (H) behind the 3 gear on output shaft
Bolts (LH & RH Side)
Gear 3 driven (G)
rd
Spline washer (F). Clutch Side Fit : Parallel Pin. Sprocket Cam Drive Cam Chain
Note : Hold the cam chain upright using a soft copper wire or a thread.
Circlip (E)
Gear 4th driven (D)
Steel bush (C) with shoulder ring
Gear1st driven (B)
Thrust washer (A)
111
112
Assembly - Engine
Fit : Washer Kick Shaft Assembly Washer
Note :
Assembly - Engine
Fit :
Square Key
Primary Gear.
Note : Ensure fitment of 2 Plain Washers on either side of Kick Shaft Assembly.
1. Ensure fitment of 2 Plain Washers on either side of Kick Shaft Assembly 2. Refer Skill tip for fitment procedure on page no....
Fit : Fit : Thrust Washer Assly Balancer Idler Gear with Special Tool Thrust washer
Body Balancer Gear.
Lock.
Bolt (A) (Use Loctite 243)
Fit : Fit : Align gear timing marks of .. Primary gear mark w.r.t crankcase mark Body balancer assly mark w.r.t crankcase mark
Parallel Pin.
Spacer
Guide gear shifter
Allen Bolt (A)
Fit :
Spring (A)
Fit : Clutch housing

Note : 1. Ensure perfect matching of gear alignment marks w.r.to crankcase marks. 2. Refer the skill tips section for understanding procedure for gear alignment marks given on page no 52.
Note :
a. Apply Loctite 638 at Bolt Shift Change (B) if removed.
b. Ensure free movement on Stopper Gear Shift in Bolt Shift Change.
Fit :
Fit : 2 Dowels Assly Balancer Idler Gear Cover 3 Bolt
Gear change lever assly
Fit :
Gear kick Idler
Using Special Tool - Primary gear holder 37 10DJ 28 & Special Nut 37 10DJ 43
Stopper
Stopper bolt (A) (Use loctite 243)
Note : Ensure loctite 638 on Kick Guide allen bolts, if removed
Fit : Spacer. Clutch Assembly Complete 'Washer Special Nut
113
114
Assembly - Engine
Fit : Clutch Cover 10 Bolts Bracket clutch cable Starter Motor Cap Screw Kick starter lever
Assembly - Engine
Note : Special nut for input shaft has LH threads.
Fit :
Bearing with plunger.
Using Special Tool : Primary Gear Holder - 37 10DJ 28
Using Sp. Tool : Centrifugal Oil Filter Nut - 37 10DJ 43
Fit :
Centrifugal Oil Filter.
Note : When assembling the Clutch Cover always remember that the entry of Kick Shaft into the Clutch Cover is the tightest as the tolerances are tightly controlled. One should concentrate on aligning the kick shaft bore and kick shaft first, rather than concentrating on the possibility of the plunger falling down. When working on vehicle It is advisable to loosen the RH Rider Footrest which helps in the above and helps also in loosening and tightening of the 2 M6 bolts partially masked by the Footrest.
Washer Magneto Side Fit : Shaft Starter Counter. Gear complete starter counter assly. Collar
Note : Always apply a thin layer of grease on to the roller bearing of starter counter gear.
Special Nut.
Using Special tool : Primary gear holder 37 10DJ 28
Fit :
Gasket
3 screws
Cover
Fit :
Fit : Woodruff key Magnet along with gear starter clutch.

Note : Always apply a thin layer of grease to the roller bearing of gear starter clutch. Add few drops of oil on OD of gear starter clutch for lubrication.
2 Dowels
Oil Pump Assembly
3 Bolts
Fit :
Starter Motor
Fit : Plate starter clutch return (A) Bolt (Use loctite 243) (B) A B
Clutch cover gasket
2 Dowels
Note : Do not apply any grease to stick Gaskets to the Clutch Cover / Magneto Cover or Crankcase. As grease deteriorates the gasket material and reduces sealing effeciency.
115
116
Assembly - Engine
Assembly - Engine
Note : Place clean piece of cloth on the Crankcase bottom end because their is chance of ring snap falling down while fitment.
Using Special Tool : Rotor Holder H6 0721 00
Fit :
Washer
Bolt
Fit : Fit :
2 Dowel
Using Special Tool : Piston Ring Holder 37 10DJ 30 Slide the Cam Chain upright with soft copper wire / Thread into cylinder Slide the piston assly into cylinder Note : Apply thin layer of oil in cylinder bore and piston assly when sliding inside for ease in fitment. Fit : Head gasket 2 Dowels (A) A Chain Guide (Non tensioner side)
Note : Holding the chain firmly bring the piston assly to TDC position and Ensure T mark on the rotor is matching with generator cover mark.
Gasket
Fit :
Magneto Cover
5 Bolts
Neutral switch coupler
Using Special Tool : Output sprocket holder 37 1030 53
Fit : Fit : Cylinder Head Assly. 2 Dowels
Bush.
Sprocket.
Plate drive Sprocket.
2 Bolts (Use loctite 243).
Top End
Fit : Fit : Spark Plug Sleeve. Grub Screw. Spark Plug
2 Dowels
Block Base Gasket
Using Special Tool : Drift 74 9309 89
Note : Before fitting the sleeve spark plug apply thin layer of molybdenum disulphide grease on the entry chambers for the O rings.
Fit :
Piston
Piston Pin
Circlip
117
118
Assembly - Engine
Fit : Cam Chain Tensioner 2 Bolt Release the tensioner plunger bolt Dust cap and O ring
Assembly - Engine
Fit : Cam Shaft. Collar.
Adjust : Check and adjust the tappet clearance Inlet Valve : 0.05 mm Exhaust Valve : 0.1 mm
Using Sp. Tool - 37 10DH 36 Fit : Cam Sprocket. Special Washer. Allen Bolt
Note :
Ensure the sprocket marks are aligned horizontally with cylinder head top machined face and the piston is at TDC.
Note : Always ensure that the piston is at the end of compression stroke and T is seen from Timing Inspection Window at generator cover. When adjusting tappet clearance.
Secure the Cam Chain Sprocket in the special tool firmly and then tighten the sprocket allen bolt.
Ensure that the O mark on washer always faces outwards when tightening the allen bolt.
Fit : Cam Shaft Cap. Apply thin layer of liquid gasket to head cover Head Cover
Fit : Tappet cap with O ring Cap magneto cover
Note :
Do not apply liquid gasket on to the cam shaft cap and other inside mounting areas.
Refer Skill Tip for more details
II
III
Fit : Copper Plated Washer Tighten bolts as per sequence Ist : 4 Domed cap nut IInd : 4 Long bolts of Head Cover IIIrd : 2 Longest bolts of Head cover
II
Note : Improper tightening sequence of bolts may cause permanent warpage in cylinder head cover and it can get damaged permanently.
119
120
Dismantling Front Fork

C Bellow clamp (A) Bellow (B) Remove :
Dismantling Front Fork
Remove :
Speedometer sensor cable from wheel (A) and from fender clamp (B)
Skill Tip : Keep it aside safely
Bolt fork (C) from the top of front fork assembly along with the O ring A B Remove : Seat fork spring (8 Allen bolt) Spacer tube Washer Spring Fork oil in a container The dust seal and the snap ring over the oil seal Recommended Oil Capacity per fork tube Approx 145 + 2.5 ml. (Drain and refill)
Remove :
Caliper assembly front mounting bolt (A)
Skill Tip : Place wedge between pads. Remove front brake lever.
Remove :
Front axle self locking nut(A)
Front axle (B)
Distance piece (C) A C D B
Wheel sensor (D)
Pull out front wheel assly
Using Special Tool : Fork for Cylinder Holder Handle 37 1830 06 & Adapter for Fork - 37 1830 11 Remove :
Remove :
2 allen bolts (A) (on either side)
Front mudguard assembly
Allen screw that is located at bottom with the help of allen key (A) by holding the fork piston with the help of a adapter (B) and holder Piston assembly
Skill Tip : Painted parts should be handled with utmost care to avoid scratches
Using Special Tool : Front Fork Tube Extractor - 74 9310 15 Remove :
Remove : A
The inner tube assembly will not come itself because of two DU bushes fitted. One bush is fitted on inner tube and other bush is fitted in outer tube. Fit the front fork tube on the vehicle by assembling the special tool (A) and lock it at number plate mounting screw. Rotate the special tool handle to seperate the inner tube from outer tube as shown in the fig. Skill Tip : Fit the fork tube without touching head light fairing Rotate special tool without hitting number plate. Remove : D C Inner tube (B) of front fork with DU bush Oil seal (C) for outer tube Guide bush washer (D) Spacer B Bushing
Rubber grommet (A)
A B
2 Allen bolts (B)
Remove :
Loosen bolt (C)
Pull down fork leg assembly by slowly rotating it
Similarly carry out the same procedure to take out other side fork leg
121
122
Assembling Front Fork

Master Cylinder
Working:
Front Disc Brake
Using Sp. Tool : Fork for cylinder holder adapter - 37 1830 08/11
Fit :
Place Fork cylinder set in the inner tube, cylinder base & place it in outer tube. Hold the piston with the help of special tool.
Bolt it from lower side of outer tube with Allen key.
When the brake lever is in idle condition, there is no pressure inside the cylinder. The feed & compensation aperture are open & connect the pressure chamber & compensation chamber to reservoir.
Guide bush, washer
Oil seal using special tool (A)
Snap Ring
Air Vent
Dust seal
Feed aperature Compensation operature Secondary seal Cover Diaphragm Reservoir Master cylinder body
When the brake lever is operated, the push rod pushes the piston inside the cylinder. A small quantity of fluid returns from pressure chamber to reservoir before primary seal completely blocks the feed aperture. Once this condition is achieved, any force exerted on the lever is transformed into pressure in the brake circuit.
Spring and fill oil.
Seat fork spring and Collar fork.

Brake Lever Compensattion Chamber Primary seal Spring Pressure Chamber Piston Outlet Port
Bolt
Similarly carry out the same procedure to assemble the other fork.
Skill Tip : The Part Name & No written on oil seal should face up side i.e. towards technician while fitting.
When the brake lever is released, the piston is pressed back quickly by the return spring to its idle position. Due to this, a vacuum is generated in the pressure chamber & the fluid in the compensation chamber flows to pressure chamber through the primary seal, the external edges of which flex approximately to allow fluid to pass to pressure chamber. After return of the master cyl. piston, the caliper retracts (after some relative time delay). This causes the fluid in the pressure chamber to return to the reservoir through feed aperture. Master Cylinder Dismantling and Assembling Dismantling : Remove front brake switch and its connection (A)
Fit :
Slide the front fork assly in the fork holder
Allen bolts
Bolt fork at the top end
Similarly carry out the same procedure for fitment of the other shock absorber. A Remove front brake lever by removing the nut and pivot bolt (B) The push rod boot (One end of the boot is held in a groove in the push rod and its other (larger) end is held in a groove in the cylinder body). B
Fit :
Front fender
2 Allen bolts (A) (2 on either side)
Fit :
Front wheel assembly.
Top cover by removing 2 screws (C)
Front axle (A)
Tighten self lock nut
Calliper assembly and tighten 2 bolts C Nylon Cap (D) Rubber diaphragm (E)
Speedometer sensor cable connection.
Caution : Dont apply excess grease or any other lubricant on the wheel sensor case.
123
124
Front Disc Brake

Caliper Assembly
Working :
Front Disc Brake
Brake fluid from the reservoir with the help of syringe/syphon pump
In the brake released condition, the brake fluid inside the caliper is at atmospheric pressure and the disc rotates freely as the pads do not press against it. When the brake lever is operated, the pressure generated in the hydraulic circuit acts on the caliper pistons. The caliper in turn push the friction pad on the side of the caliper body against the rotating disc. The friction pad on the other side of the disc also presses against the disc due to reaction force on caliper body. Thus both the friction pads press against the disc, thereby generating braking torque.
Master cylinder along with hose assembly from handle bar by removing the 2 flanged 8 bolts (F) on the clamp. Brake hose from master cylinder outer by removing banjo bolt (G) Wipe out clearly the outer surface of master cylinder.
Hose Bleeder Screw Banjo Bolt
Skill Tip :
When the lever is released, the pressure in the hydraulic circuit return to atmospheric level. The friction pads return to idle position due to return of the caliper pistons which is due to the spring action of the seals.
Ensure that there should not be any spillage of brake fluid on
painted parts
Safety Tip :
Pin Piston Disc Pad Disc Pad Piston Seal Caliper Body Carrier Bracket Dust Seal
When the pads wear, the pistons move further towards the Disc during brake application, but after release of pressure they retract only to the extent allowed by the spring action of the seal. The pistons therefore take up new positions in idle condition, and thus provide automatic adjustment to compensate for pad wear. Due to this reason, there is no need for free play adjustment in the Brake Lever in Master Cylinder.
Take care of your eyes while working with brake fluid.
Hold the master cylinder in a soft jaw vice.
Remove circlip with the help of a plier, by pressing the piston slightly inside the bore, with a nylon or wooden rod.
Take out the piston assembly along with the Return spring by pulling it out.
If transparent window in the cylinder body for level indication needs replacement (due to damage, etc.) proceed as follows:Disc
Remove Lock Ring on the window with screw driver
Remove window and O ring.
Master Cylinder Assembly :
Dismantling of Caliper Dismantling the Assembly A B Remove caliper mounting bolts (A) Remove banjo bolt (B) Remove caliper from fork Removal of Pads : Remove the pad retaining bodys Allen bolt Remove the pads Remove the pad spring from the caliper body with a screw driver Piston and Piston Seal Removal : Wipe out cleanly, the outer surface of the caliper. Remove LH pad retaining case by removing allen bolts Put a wooden wedge in between the piston and caliper. Blow compressed air into cylinder through benzo bolt hole where the brake hose was fitted, with the air pressure, the piston will be pushed out of cylinder.
Never allow mineral oil to come in contact with seal or other rubber parts of disc brake, since it will cause damage to these parts.
Free play at the end of the lever is provided to ensure that in the free condition, the piston does not remain in the pushed condition, This ensures that there is no pressure in the system when the brake is not applied.
125
126
Front Disc Brake

Inspection and Maintenance Frequency
Check Points Brake Fluid Level / Leakage Frequency
Front Disc Brake
Warning : Do not apply high pressure compressed air, which will cause the piston to jump out of the cylinder. The piston should be taken out gradually with moderately compressed air. Care to be taken not to damage the sealing surface of the inlet port while applying air pressure.
Do not place your finger in front of the piston while applying compressed air to push it out. Remove piston seal using a thin part like a thickness gauge, etc.
Inspect during every service / every 2500 Km refil up to upper limit (till step on the inner side of the reservoir) if level is low. Replace brake fluid every two years. (In severe operating conditions, replace in a year.)
Caution : Be careful not to damage inside (bore side) of the cylinder.
Skill Tip : While assembling use loctite paste 243 on allen bolt for mounting LH pad retainer case.
Brake Lever Operation
Inspect during every service/every 2500 Km
Assemble the caliper assly in reverse order of dismantling
Air Bleeding of Disc Brake System :
For air bleeding from front Hydraulic brake system first top up the master cylinder with hydraulic oil. Brake Pads lInspect during every 2500 Km thereafter for wear and condition of linings.
Operate the brake lever slowly in order to get filled the oil in the circuit.
Connect transparent tube to the bleeder screw at caliper or syphon pump
Operate the brake lever and keeping in pressed position loosens the bleeder screw so that some oil escapes with the air bubbles.
Keep on operating the brake lever till the air bubble escape out completely through bleeder screw, and top up the master cylinder if required. Brake Disc Inspect during every 5000 Km. and every 2500 Km thereafter.
Once the air escapes out from the hose pipe the brake lever meets resistance, which indicates completion of air bleeding
After completing the bleeding, top up the master cylinder up to the maximum level mark.
Also syphon pump can be used for air bleeding
Check for excessive scoring marks on friction surface of disc, and run out.
Brake Fluid for Disc Brakes
Always use only recommended brake fluid from sealed container to ensure durability of the system. Never reuse brake fluid removed from a system. Master Cylinder & Caliper Inspect every 5000 Km for leakage.
Important points on 2 wheeler disc brake system :
1. Since front disc brake is more powerful than drum brake, apply front and rear brake together gradually. Avoid braking during turning.
2. Use only DOT 3 or DOT 4 brake fluid from a sealed container from recommended makes.
3. Do not apply mineral oil for cleaning any brake parts. Use only brake fluid for cleaning the seals.
4. Do not apply mineral based grease on bore, pistons and seals of master cylinder and caliper. Apply only recommended assembly fluid. Brake Hose Inspect for leakage & damage during every service / every 2500 Km.
5. Do not use cotton cloth to wipe cylinder bore, fibres of cloth will remain in cylinder bore surface.
6. Ensure dust free condition during assembly.
7. Do not polish friction disc with sand paper, as hard particles deposited in the lining may damage steel disc.
8. While filling the reservoir after bleeding, ensure that drops or splashes do not remain on the painted surface or plastic surface, since brake fluid is corrosive.
127
128
Maintenance - Electricals
Remove vent plug strip Top up level with distilled water in between Min and Max. level Connect battery to charge and ensure respective terminal are connected properly Set charging current at 0.9 A DC Charge battery for 3/4 hrs., then check voltage and special gravity. Voltage should be 12.5 volts and special gravity in all 6 cells should be 1.240. This is a confirmation check for a fully charged battery. Disconnect the battery from the changer. Fit vent plug strip firmly. Hydrometer Connect battery on to vehicle. Apply petroleum jelly on to the battery terminal. Read Here a. Undercharging.
Battery
Technical Specification :
happens, the chemical reactions within the battery are affected and results in loss of capacity. Mostly the causes of sulphation are as under :
Type & Capacity

0
12V - 9 AH
Specific gravity of electrolyte for initial filling of new battery
1.24 for use above 10 C
b. Standing in a partially or completely discharge condition for long time. c. Low electrolyte permitted to fall plates, then the and will become level : If electrolyte level is below the top of the battery exposed surfaces will harden sulphated.
Specific gravity of electrolyte for initial filling of new battery
1.28 for use above 100C
Initial charging duration
10 ~ 15 hrs
Initial charging current
0.9 to 1 Amp
d. Adding acid : If acid is added to a cell in which sulphation exists the condition will be aggravated. e. High specific gravity : If specific gravity is higher than the recommended value, then sulphation may occur. f. High temp.: High temperature accelerates sulphation, particularly of an idle, partially discharged battery.
Initial Charging Procedure
1. Fill each cell with battery grade sulfuric acid of the correct Sp. gravity (1.24 at room temp. 0 for use above 10 C and 1.28 at room temp. 0 for use below10 C).
Battery Maintenance
For the optimum performance and longer battery life the maintenance of battery is important. a. Always keep the battery clean and dry.
2. Allow the battery to stand for 30 min. after filling.
Voltage of the sulphated battery : Cells of the sulphated battery will show low specific gravity. Follow the procedure given below. Check voltage before charging. Charge for 2 hours
3. Keep vent plugs open. Connect battery to charger and charge at 0.9 Amp.
4. Charge continuously for 10~15 hours taking Sp. gravity readings every hour. Fully charged condition is indicated when all cells are gassing freely and evenly and show no rise in specific gravity over 3 successive readings. battery inside the box provided on floor board. Fasten the battery firmly with bracket & allied fasteners. c. Connect cables to the positive and negative terminals properly. Reverse connections will damage the charging system permanently. d. Always connect the negative (earthling) terminal at Iast.
b. Visually inspect the surface of the battery container. If there are any signs of cracking or electrolyte leakage from battery, replace the battery. Never add acid or ordinary tap water for topping up since this will shorten Battery life.
5. After charging push vent plugs strip firmly into place and wash off acid spillage with water and dry the battery.
Non Use Maintenance

When the vehicle is likely to remain off-road for longer, time (say more than a month) then Non Use Maintenance should be carried out as follows otherwise the battery may get sulphated and permanently damaged. a. Remove the battery from vehicle. b. Maintain electrolyte at Upper Level. c. During off service period, battery should be charged once a month. d. Keep the battery fully charged. e. Store the battery in cool, dry place. f. Keep the battery away from rain, dew, moisture and direct sunlight.
Checking the Specific Gravity
Check voltage every 1 hour. If voltage increases then continue charging. But if voltage does not increase, discontinue charging. Otherwise battery charger will get permanently damaged. If battery is not badly sulphated (i.e. voltage more than 9 volts), then battery can be revived by special treatment. In such case it is advisable to give sulphated battery to authorised dealer of battery manufacturer for necessary special treatment.
The charge condition of the individual cell can be checked by measuring Sp. gravity of electrolyte in that cell. The specific gravity of electrolyte can be checked by using Hydrometer having small diameter spout. e. Clean the battery terminals and cable connections. Smear them with petroleum jelly to avoid corrosion g. Check that the battery cable connections are firm and cables do not rub against any metal components.
How to Determine Condition of Battery
For measuring the Sp. gravity bring the electrolyte in the Hydrometer to eye level, and read the graduations on the float scale bordering on the lower meniscus (i.e. curved down portion of electrolyte surface) as shown in the figure. After charging is over, fit the filling caps strip, wash acid spillage with water. Dry the battery. Ensure terminals are clean.
Battery Charging Procedure :

This is a M.F (Maintenance Free) battery. This battery is not having any exhaust tube instead it has a unique vent mechanism.
Battery Installation:
Install the battery on vehicle as described below
a. Ensure that in all six cells the level of electrolyte is near the maximum level mark. Clean battery throughly
The electrolyte level in this M.F. battery needs to be topped up with distilled water once in a year. In case battery in discharged and needs to be charged using battery changed procedure is as follows : Remove battery from vehicle
Battery Sulphation
A sulphated battery is one which has been left standing in a discharged condition or undercharged to the point where abnormal lead sulphate has formed on the plates (Sulphate cells looks like white crystal like sugar). Where this
Specific gravity check: - Whether battery is fully charged or partially charged, it will always show same no load voltage of 12 volts or more (unless battery cells are damaged due to sulphation etc). But specific gravity of the fully charged battery and partially charged battery will be different. Fully charged battery will show Sp. gravity of 1.240 while partially charged battery will show less specific gravity. Therefore, specific gravity check is very important to know condition of the battery.
b. To clean and dry the surface wipe the top of the battery with a clean cloth. Install the
129
130
Brown ON (Vehicle in neutral) OFF (Vehicle in gear) Blue CDI Unit and H. T. Coil Inspection :
CDI unit can be checked using OK H.T. coil on Electronic Test jig Similarly H.T. Coil can be checked using OK CDI unit on electronic Test jig Measure the primary winding resistance as follows Connect the hand tester between the coil terminals. Measure the secondary winding resistance as follows Remove the plug cap by turning it counter clockwise. Connect the tester between the spark plug leads. Measure primary winding resistance. Measure secondary winding resistance. If the valve does not match as per, replace the coil. Primary Winding
Reading 200+22 ohm
Switches :
a. Front Brake Light Switch Inspection :
i. ii.
iii. Brown White Black / White Black / Yellow OFF ON
Turn ON the ignition switch. The brake Light LED Blank should get on when the front brake (Lever is pressed) is applied. If it does not, check the Front brake switch.
e. Ignition Switch :
H.T. Coils : (Inspection Using Multimeter)
Brown
Blue
Lever Pressed
Lever Released
b. Rear Brake Light Timing Inspection :

i. ii. Disconnect stator plate coupler Set multimeter on ohm range. (Ohm Meter)
g. Stator Plate Coils Inspection :
i. ii.
Range Meter +ve White/Red Black/Yellow Meter -ve 2 K Connections
Pickup Coil Resistance :
iii.
0.40 to 0.49 Ohms Secondary Winding 4.23 to 5.17 K Ohms
Turn ON the ignition switch. Check the operation of the rear brake coils light switch by depressing the brake pedal If it does not operate as specified, adjust the brake light switch or check Rear brake switch
Brown
Blue
Pedal Pressed
Range Meter +ve Red Black/Yellow 14+1.4 Meter -ve 200 Reading
Excitor Coil :

Pedal Released
If the meter reads as specified, the ignition coil windings are probably good. However, if the ignition system still does not perform as it should after all other components have been checked test replace the coil with one known. Visually inspect the secondary winding lead. If it shows any damage, replace the coil.
c. Fuel Level Indicator :

Range Meter +ve Blue/White Blue/White 1.3+0.13 Meter -ve 200 Reading
i.
Battery Charging Coil :

Fuse Inspection (Capacity = 10 Amp)
Meter -ve Black/Yellow 0.7+0.07W Reading
ii.
Inspect the fuse element If it is blown out, replace the fuse.
For knowing then quantity of fuel inside the fuel tank at a glance, is provided on Speedo consle. The fuel gauge works on the principle of variable resistance. The fuel gauge works on D.C supply. For checking the resistance across the sender and across the gauge, make the connections verify the readings, make the connections verify the readings as tabulated below
Range Meter +ve Yellow/Red 200
Lighting Coil :
If a fuse fails during operation, the electrical system to determine the cause, and then replace it with a new fuse of proper amperage.
Caution : When replacing a fuse be sure the new fuse matches the specified fuse rating for that circuit. Installing of a fuse with a higher rating may cause damage to wiring and components.
Connection
Tank (Float)
Resistance
White / Yellow Meter
Full 4 - 10 W (Highest position)
10 W Black / Yellow
95~105 W Empty (Lowest position)
Relay (Inspection Using Multimeter) : Coil Resistance X 200 Ohm Meter +ve Brown Meter -ve Green/White Reading 55+5.5 Ohm Also this relay can be checked on electronic Test jig.
d. Neutral Switch :
i.
ii.
The neutral switch will be in ON position only when the engine is in neutral position. The neutral light will not glow when vehicle is in geared position
131
132
REGULATOR RECTIFIER UNIT
Rectifier & Regulator Assembly :
AC Voltage Measurement :
DC Charging Voltage Measurement : (Use fully charged battery while measuring)
To measure AC voltage, open the headlight housing. Start the engine and set it at 4000+25 RPM. Ensure that the headlight, tail light, Speedometer light are ON and the dipper switch is at Hi beam position.
L/W L/W W
Connect AC voltmeter in parallel across the AC circuit load by connecting the +ve meter lead to red/black lead from the dipper switch and the -ve meter lead to ground.
Measure AC lighting voltage at 4000+25 RPM. The voltage should be 13.5+0.5 V. Stop the engine. Disconnect the meter leads. Reassemble the headlight housing.
To measure the DC voltage; set the meter at 20VDC range. Connect the meter +ve lead to white from RR unit and meter -ve lead to ground. Start the engine and set it at 4000+25 RPM. Measure the voltage with and without headlight switch to the ON position. Stop the engine disconnect the meter leads. Meter Range Specification at 4000+25 RPM DC 20 Volt 14 ~ 15 V
Meter Range
L/W L/W W
Specification at 4000+25 RPM
AC 2o Volt
14.2
13.7 + 0.3 V
Multimeter connected in Parrallel with Battery for checking DC charging voltage
AC Lighting Circuit :
FUSE (10 Amps.)
W/B
L/W
CONTROL SWITCH RH
R
PIN NO.3 HIGH BEAM INDICATOR

STARTER RELAY WITH DAMPER MAGNETO
R/B
R/B
BATTERY 12V-9Ah
PIN NO.2 INSTRUMENT CLUSTER + INPUT BODY CONTROL UNIT AC INPUT & OUTPUT Y R/B Y/R REGULATOR RECTIFIER UNIT
Br
Br
PIN NO.11 COMMON GROUND
B/Y
B/Y
INSTRUMENT CLUSTER
PIN NO.13 POSITION LAMP ON- INPUT
PIN NO.20 PERMANENT BATTERY + INPUT
20 PIN COUPLER WITH DUST COVER

Y R R/Y Y Y/R
L/W
O O F N F
Battery DC Charging current : (Use fully charged battery while measuring)
13.5
IGNITION SWITCH
Br
Br
W R W R TAIL/ STOP LED ASSLY
L/W
FUSE 10 Amps Y/R W/B NO. PLATE LAMP 5 W
R/B LIGHTING COIL B R STARTER RELAY 70A RATING BATTERY 12V-9Ah
R/B
HEAD LAMP ASSY/LAMP 12V-35/35W HS1
B/Y
B/Y
L/W
To measure the DC charging current, set the meter at 20ADC. Connect meter+ve lead to White/black lead from RR Unit and meter -ve lead to battery +ve lead.
R/Y
R/Y
Multimeter connected in Series with Battery for checking DC charging Current

0.9
Start the engine and set it at 4000+25 RPM. Measure the DC charging current. The DC charging current should be 2 A max stop the engine and disconnect meter leads. Connect the RR unit and battery
Meter Range
L/W L/W W
POSITION LAMP 12V-5W- 2 NOS.
Connection DC10A
Specification
R MAGNETO
Meter +ve Meter -ve 2 A max at White/Black Battery (+) 4000+25 RPM terminal of lead (White) R/R
FUSE (10 Amps.)
W/B
L/W
L/W
R BATTERY 12V-9Ah STARTER RELAY WITH DAMPER

MAGNETO
133
134
Speedometer/Tachometer Console
Back-lit, Non-contact Handlebar switches : The control switches on both sides of the handlebar are conventional to look as, in terms of switch positioning. The main features of these are ... Operation is based on non-contact
The speedometer has a wide Digital LCD screen with a orange backlit display mode for superb visibility of display during night riding condition.
This entire speedo console houses following :
A large analogue tachometer with self testing mechanism.
A red LED indicator showing low fuel level inside the fuel tank. And also indicates a flashing signal when engine RPM exceeds above 9000 RPM. Thus ensuring safety of rider and engine.
mind and wants to continue straight ahead. The rider has only to re-select the opposite side indicator again to cancel the previously selected indication. (There is no depress to cancel function) The other feature which has been incorporated in the switches is the illumination of the tell-tale icons. The illumination is backlit by LEDs which again are long-life and have a pleasant bluish-white glow to them. All the icons like the turn indicators, low beam, high beam, horn, starter etc. glow when the Parking or Headlight switches are put ON.
Digital Displays for
- Odometer
- Trip meter (Unique facility of resting the trip meter 1 & 2 respectively) - Fuel level indicator
Switching is done without physical contact There is no wear and tear Life would be equal to that of the bike itself. The operational force required for the switches has been kept as low as possible to give a light feel and reduce fatigue for the rider.
A row of indication LED displaying functioning of
Checking of switches on handle bar : As like in conventional switches, since switch is not having any electrical contact, We cant check the switch functioning (Continuity) by multimeter. But it can be checked on electronic test jig. Clutch Switch : The clutch switch has 3 wires and it has contact configration of This vehicle is not having interlock relay Instead its working is taken care of by clutch
Light Green Yellow/GreenBlack/Yellow
- Neutral Light
- High beam
- Turn signal
- Side stand ON
Working of Switches : These are non-contact type switches, so instead of contact set it consists of hall sensor and magnet combination. Whenever any handlebar switches is pressed the hall sensor gets operated and its output signal is gives to a BCU (Body Control Unit) and BCU further calculates and gives precise signal to the respective unit for functioning. e.g.
with a unique Day-Night mode functioning feature for riders convenience and safety.
Horn Switch
BCU
Horn
OFF Clutch Lever Released
Note : The speedometer console has a unique builtin memory logic function which stores all the data like distance covered etc. in its memory even if DC supply is disconnected.
Pass Switch
BCU
Head Light High Beam
ON Clutch Lever Released
Vehicle Speed Sensor
Body Control Unit (BCU) : This is a sealed Electric Control Unit located inside head light assly. -
Non Contact Wheel Sensor : In LCD speedo console there are no physical moving parts as sensing of wheel speed is through a Non Contact hall effect Sensor. The hall sensor is a electronic switch which operates due to magnetic field. The sensor has 3 wires supply, earth and output whenever during rotations of wheel magnet passes through sensor. A signal is given to speedometer through a wire to speedometer which displays speed of vehicle in km/hr.
Tail Lamp : The illumination for Tail lamp and Brake lamp are done through 2 rows of LEDs each. These are high intensity LEDs the main advantage of these LEDs is they consume very less power. i.e LED consumes 3W power against 21 W power of a conventional brake lamp. When you operate light control switch to glow but intensity will be very low. As soon as you operate brake switch the brightness of LED increases to size you bright light.
This changeover of intensity is maintained with the help of electronic circuit placed inside Tail Lamp Console assly and is a totally sealed unit.
Self Indicator Switch : In the conventional type of switches the rider has to manually depress the Turn Indicator knob or return the Turn indicator knob to its non-signalling position. In UG III there is no separate press to off buttons for cancelling side indicator signal. This feature is achieved by providing a self cancelling hall sensor and magnet fitted on steering column assembly. This cancellation signal is processed through BCU and then side indicators are switched off. The self cancelling feature automatically turns of the indicator of the indicator under 3 conditions. The first indication is when after the turn has been completed and the handlebar comes to a straight ahead position, the indicators switch off by themselves. The second condition is when the rider has selected a right or left turn but not physically done the turn and is continuing to go straight ahead and may be unaware of the enabled turn signal too. A timer function gets enabled which switches off the indicators after a pre-set time. The third condition is when the rider has selected for eg. a left turn, but changes his
In case of overload or short circuit, BCU has a short circuit/overload prevention facility. This vehicle does not have a flasher. The flasher operation is carried out by BCU only. In case of failure of one of the filaments of head lamp. The BCU will automatically changeover to IInd filament. This is provided for safety rider during night driving conditions. If customer operated starter switch contunuously 3 times in a go for 4 th cranking BCU will disable cranking operation and next cranking would be possible after 20 second only. This feature is added which gives better battery life. Maintenance : Ensure no direct high pressure water water is applied on Speedo console and wheel sensor.
135
136
Br
L/W
B/Y
INSTRUMENT CLUSTER
R/Y
R/B
PIN NO.6 VEHICLE SPEED SENSOR OUTPUT PIN NO.7 TALE-TELL BLINKER- RH INPUT PIN NO.8 TALE-TELL BLINKER- LH INPUT PIN NO.9 TALE-TELL NEUTRAL INDICATOR PIN NO.10 TACHOMETER PIN NO.11 COMMON GROUND PIN NO.13 POSITION LAMP ON- INPUT PIN NO.20 PERMANENT BATTERY + INPUT
R/W
Br/B
B/Y
Br
Gr G Lg B B/Y R W
Gr FRONT BRAKE SWITCH H.T. COIL B/Y FUEL LEVEL GAUGE Br REGULATOR L SPARK PLUG B B B/Y B/W W/R R B/R G Lg B B/Y R W/Y B/Y
Gr
L/W
L/W
W/R
B/Y
Br
Y B/ Y W L/W L/W Y/R
Br
B/Y
Br
Y B/ Y W L/W L/W Y/R
H.T. COIL
SPARK PLUG
B/Y
B/Y
O/Br
HEAD LAMP ASSY/LAMP 12V-35/35W HS1 POSITION LAMP 12V-5W- 2 Nos.
B/Y R/Y B/Y
B/Y R/Y R EARTH-FRAME R L/W L/W Y/R / R W O/Br B/Y Lg B/Y B/ Y R R STARTER MOTOR Br/B Br/B R/W B/Y B/Y SIDE STAND SWITCH Lg W ASSY. LIGHT NO. PLATE
R L/W L/W Y/R W/R
Y/G
W/B
SIGNAL LAMP FRONT LH G Lg G
B/Y
B/Y
B/Y
R/B
R/B
B/Y
Y/G Y/G
NEUTRAL SWITCH
C PU OIL LS ING
137
Pulsar DTS-i UG-III-180cc Training Notes Dealer Development Center Dealer Development Center Pulsar DTS-i UG-III-180cc Training Notes
SIGNAL LAMP FRONT RH LAMP 12V-10W Gr B/Y Gr B/ Y CONTROL KIL SWITCH SWITCH RH
POSITIVE SUPPLY
Notes :
Speedo console should not be kept inverted Ensure there are no scratches/breakage on console cover Dont open rubber pins located on back side of speedo under any under any circumstances. Ensure speedo console and harness mating coupler is always covered by rubber cover. Handle wheel sensor carefully while working on front brake drum relating problems. Ensure sensor cable is intact. Do not apply in grease or lubricant in between the rotating parts. Do not open control switches and dont apply any grease or lubricant.
Main Electrical Wiring Diagram
CONTROL SWITCH LH NOT USED
LH SIDE IND. OUTPUT RH SIDE IND. OUTPUT GROUND
MAGNET ASSLY (S.C.B. UNIT)
PIN NO.1 VEHICLE SPEED SENSOR + INPUT PIN NO.2 INSTRUMENT CLUSTER + INPUT PIN NO.3 HIGH BEAM INDICATOR PIN NO.4 TALE-TELL SIDE STAND INDICATOR PIN NO.5 FUEL GAUGE INDICATOR
R/W Br R/B O/Br W/Y
R/W Br R/B O/Br W/Y
R/W VEHICLE SPEED SENSOR FROM RH SWITCH FROM LH SWITCH SWITCH- BODY CONTROL UNIT SWITCH ASSY. AC INPUT & OUTPUT DC INPUT & OUTPUT HALL SENSOR ASSLY (S.C.B. UNIT) C.D.I. ASSY. FROM S.C.B. UNIT
B/R
REAR BRAKE SWITCH
Gr B /Y
Gr B/ Y
SIGNAL LAMP REAR RH
O O F N F
IGNITION SWITCH
Br W B/W B/Y
Br W B/W B/Y R/W
L B/ Y R /W
L B/ Y R
TAIL LAMP ASSY TAIL/ STOP LED
R B/ Y G G SIGNAL LAMP REAR LH
FUSE 10 Amps
CABLE ASSEMBLY EARTH
R Lg B/Y HORN (LH) HORN (RH) STARTER RELAY 70A RATING BATTERY 12V-9Ah
B/Y CLUTCH SWITCH
MAGNETO
CABLE ASSY. RED
138
Individual Circuit Diagrams

Brake Light Circuit :
REED SWITCH ASSY. (TPS) C.D.I. ASSY.

FRONT BRAKE SWITCH REAR BRAKE SWITCH
Ignition Circuit :
B/R
H.T. COIL No. 2 (For Secondary Spark Plug) SPARK PLUG
Br
B/Y
B/W
W/R
B/R
G Y
Br
Br
B/Y
B/W
H.T. COIL No. 1 (For Primary Spark Plug) SPARK PLUG W/R
O O F N F Br IGNITION SWITCH W L
O O F N F
IGNITION SWITCH
B/W
B/W
B/Y
B/Y
Br
W/R
B/Y
FUSE 10 Amps W/B
EXCITER COIL
Kill Switch
B/Y
W/R
B/Y
STOP LAMP LED BANK
B EARTH-FRAME STARTER RELAY 70A RATING BATTERY 12V-9Ah
MAGNETO
Battery Charging Circuit :
C PU OIL LS ING
Horn Circuit :
CONTROL SWITCH LH
BODY CONTROL UNIT
B/Y
L/W
L/W
Br
B/Y
O O F N F Br IGNITION SWITCH W W Br
B/Y
B/Y
Br/B
B/Y
L/W
L/W
FUSE 10 Amps W/B
EARTH-FRAME
Br/B
B R B/Y B/Y Br/B Br/B BATTERY 12V-9Ah
FUSE 10 Amps W/B R
BATTERY CHARGING COIL STARTER RELAY 70A RATING
STARTER RELAY 70A RATING
BATTERY 12V-9Ah
MAGNETO
HORN (LH)
HORN (RH)
139
140

Side Indicator Circuit :
CONTROL SWITCH RH POSITIVE SUPPLY Gr B/Y GROUND BODY CONTROL UNIT AC INPUT & OUTPUT Gr G G G Y Y/R R/B PIN NO.8 TALE-TELL BLINKER- LH INPUT B/Y Br B/Y B/Y PIN NO.7 TALE-TELL BLINKER- RH INPUT Gr Gr REGULATOR RECTIFIER UNIT B/Y PIN NO.2 INSTRUMENT CLUSTER- INPUT BODY CONTROL UNIT Br Br CONTROL SWITCH LH RH SIDE IND. OUTPUT LH SIDE IND. OUTPUT Gr SIGNAL LAMP FRONT RH
AC Lighting Circuit :
PIN NO.3 HIGH BEAM INDICATOR
R/B
R/B
PIN NO.2 INSTRUMENT CLUSTER + INPUT
Br
Br
B/Y
B/Y
INSTRUMENT CLUSTER
PIN NO.13 POSITION LAMP ON- INPUT
R/Y
O O F N F Y/R Gr PIN NO.20 PERMANENT BATTERY + INPUT W Br B/Y TAIL/ STOP LED Assly O O N F F Br W B/Y W Br IGNITION SWITCH W
IGNITION SWITCH
Br
Br
W R W R
Gr B/Y
Gr
SIGNAL LAMP REAR RH B/Y
R FUSE 10 Amps Y/R W/B NO. PLATE LAMP 5 W
B/Y W B/Y
R/B LIGHTING COIL B R STARTER RELAY 70A RATING BATTERY 12V-9Ah G SIGNAL LAMP FRONT LH
R/B
HEAD LAMP ASSY/LAMP 12V-35/35W HS1
B/Y
B/Y
R/Y
R/Y
G B/Y W/B FUSE 10 Amps
SIGNAL LAMP REAR LH
POSITION LAMP 12V-5W- 2 NOS.
BATTERY 12V-9Ah R B EARTH-FRAME STARTER RELAY 70A RATING
R MAGNETO
Speedometer and Tachometer Circuit :
Fuel Indicator Circuit :

W/Y PIN NO.5 FUEL GAUGE INDICATOR W/Y
PIN NO.1 VEHICLE SPEED SENSOR + INPUT
R/W
R/W
Br
Br
VEHICLE SPEED SENSOR
FUEL LEVEL GAUGE PIN NO.2 INSTRUMENT CLUSTER + INPUT Br Br
B/Y
PIN NO.6 VEHICLE SPEED SENSOR OUTPUT
L/W
L/W
INSTRUMENT CLUSTER
PIN NO.10 TACHOMETER C.D.I. ASSY.
INSTRUMENT CLUSTER
W/Y
PIN NO.11 COMMON GROUND B B/Y B/Y
O N B IGNITION SWITCH
O O N F F
O F F
Br W
Br W B/Y W
Br
Br
IGNITION SWITCH W W FUSE 10 Amps W/B BATTERY 12V-9Ah B R
B/Y
B/Y
B/Y
SPEEDOMETER COUPLER
W/Y
B/Y
B/Y
FUSE 10 Amps W/B
EARTH-FRAME STARTER RELAY 70A RATING BATTERY 12V-9Ah
141
TURN SIGNAL SELF CANCELLATION DEVICE B
142

Side Stand Indication Circuit :
Stator Motor Circuit :
PIN NO.9 TALE-TELL NEUTRAL INDICATOR
Lg CONTROL SWITCH RH
Lg
PIN NO.4 TALE-TELL SIDE STAND INDICATOR
O/Br
Br
Br
PIN NO.11 COMMON GROUND BODY CONTROL UNIT DC INPUT & OUTPUT Please note that Starter Switch is enable only if Kill Switch is in OFF condition.
Br
Br
INSTRUMENT CLUSTER
INSTRUMENT CLUSTER
Br
O O N F F
B/Y
IGNITION SWITCH Y/G W
Br
Br
PIN NO.20 PERMANANT BATTERY + INPUT
SPEEDOMETER COUPLER
R B/Y
O O N F F IGNITION SWITCH W Br W
Br W W B/Y
R/W
STARTER MOTOR
W/B
EARTH-FRAME Lg
B/Y
FUSE 10 Amps
O/Br
B/Y
B/Y
Lg R R/W STARTER RELAY 70A RATING BATTERY 12V-9Ah NEUTRAL SWITCH B
B/Y
B/Y
W/B
Lg
FUSE 10 Amps
Y/G
Y/G
O/Br
B/Y
EARTH-FRAME
SIDE STAND SWITCH
BATTERY 12V-9Ah
Neutral Light Circuit :
PIN NO.9 TALE-TELL NEUTRAL INDICATOR
Lg
Lg
Br
Br
INSTRUMENT CLUSTER
B/Y
B/Y
Br
O O F N F W W Lg FUSE 10 Amps W/B
Br
Br
IGNITION SWITCH
Lg
NEUTRAL SWITCH
BATTERY 12V-9Ah
143
144
DTSi Trouble Shooting
High Fuel Consumption

OK 4th Step : TPS Related Check accelerator cable free play for TPS function Not OK If OK Accelerator Cable Free Play 2~3 mm OK
1st Step : Idling RPM Related Adjust idling to specified idling rpm by idling adjusting screw 1400 + 100
Check idling RPM as per specification
Not OK
Adjust accelerator cable free play
Idling RPM
OK
Replace accelerator cable if sticky / jam
2nd Step : Air Induction Related

Not OK
5th Step : Front Wheel Rotation Related Adjust front brake lever free play if less than specified
Check air filter foam element for no clogging / correct oil soaking
Check front wheel for free rotation
Not OK If OK Clean air intake duct if blocked / clogged
Clean air filter foam element (fine & corse) as per SOP if clogged / excess oil soaked
Front Brake Lever Free Play 2~3 mm If OK
OK
3rd Step : Choke Related Lubricate / Replace choke plunger if sticky / jam If OK
Check disc for run out
Check free movement of choke knob
Not OK
If OK
Check proper fitment of wheel bearing Disc side
Clean choke plunger if sticky / jam

OK If OK Using following sequence Tighten the fasteners as Axle Nut, Mudgaurd Mounting Bolts, Lower T, Upper T, Cap nut
OK
Continued.....
Continued.....
145
146
OK 8th Step : Spark Plug Related Not OK If OK Adjust rear brake free play if less than specified
OK
6th Step : Rear Wheel Rotation Related
Check rear wheel for free rotation
Not OK
Clean & adjust spark plug gap as per specification
Rear Brake Pedal Free Play 25 ~ 30 mm If OK
Check spark plug for no fouling / correct heat range & gap. Check both spark plug for DTS-i engine
Replace spark plug by recommended one if incorrect heat range If OK
Lubricate rear brake pedal shaft if dry / sticky If OK OK
OK Lubricate rear brake cam if sticky / jam
Replace spark plug if fouled
9th Step : Carburettor Related Not OK Adjust VC screw as per specification & CO limit If OK
7th Step : Clutch Cable Related Adjust clutch lever free play if less / more than specified If OK
Check clutch cable for free play & smooth operation
Not OK
Check carburettor for correct air fuel mixture with the help of CO gas analyser
Standard CO % = 1.75 to 2.25% Std. VC Screw Settings = 2.5+2 Turns
Correct e clip position as per specification If OK
Clutch Cable Free Play Correct clutch cable routing If OK
2~3 mm
Clean carburettor body air passages if clogged If OK Replace carburettor jets if worn out If OK Replace needle valve & its seat if worn out Continued..... Continued.....
Replace clutch cable complete if sticky / jam
OK
147
148

OK 12th Step: Engine Compression Pressure Related
OK
10th Step : TPS Related Adjust gap between magnet & reed switch as per specification if found more
If compression pressure in wet test is NOT OK Check & Rectify cylinder head related reasons
Check TPS for correct gap / free movement / magnet presence / continuity
If OK
Not OK
Check compression pressure. Perform dry & wet compression test
If compression pressure in wet test is OK Check & Rectify cylinder block related reasons
Standard Gap Between Magnet & Reed Switch

If OK
Clean TPS switch if stuck up / sticky operation
2.5 mm Replace magnet if missing
Clean compression ring & piston groove if sticky / jam
OK
If OK
Correct valve timing if mark on cam sprocket not aligning with cyl. head when rotor T mark is aligned with crankcase L.H. mark
Replace TPS switch if reed switch short / open circuited
Replace piston ring set if compression ring worn out
11th Step : Ignition Timing Related Replace CDI if timing is incorrect

If OK
Check ignition timing
Not OK
* Reset valve tappet clearance as per specs. if found less Replace cylinder block piston assembly if worn out / excessive clearance Clean valve guide & valve stem if gummy substance deposited
Replace rotor if cam position wrong leading to incorrect ignition timing

If OK
Replace cylinder piston assembly if partially seized
Replace H.T. coil for malfunctioning
OK
Rectify valve seat and valve face by lapping if pitted / worn out / excess carbon deposition Inspect De-comp mechanism for stickness
Inlet
Exhaust 0.05 mm 0.10 mm
*Standard Tappet Clearance
Continued.....
Replace inlet & exhaust valve if bent
149
150

OK 4th Step: Engine Compression Pressure Related
Poor Pick-up & Poor Acceleration
1st Step : Fuel Related Replace fuel from petrol tank, cock & carburettor bowl
Check fuel for no adulteration / contamination
Not OK
If compression pressure in wet test is NOT OK
If compression pressure in wet test is OK
OK Clean air intake duct if blocked If OK Clean air filter foam element as per SOP if clogged / excess oil soaked
2nd Step : Air Induction Related
Check compression pressure. Perform dry & wet compression test Check & Rectify cylinder head related reasons
Check & Rectify cylinder block related reasons

Skill Tip : Do not scribe. Clean by Acetone/CCL4.
Not OK
Check air induction system for no choke-up / no clogging i.e. correct quantity & smooth supply of air
Correct valve timing if not OK
OK Re-adjust V.C. screw as per specifications
3rd Step : Carburettor Related
Not OK If OK Correct e clip position as per specification If OK Clean main jet, pilot jet if clogged If OK Clean carburettor air & mixture passages if clogged If OK Correct diaphragm position if wrong If OK Replace carburettor piston valve assly if diaphragm punctured
Check carburettor for correct air fuel mixture with the help of CO gas analyser
Reset valve tappet clearance if not as per specifications
Clean compression ring & piston ring if sticky / jam
Tighten cylinder head bolts if loose
Replace piston ring set if compression ring worn out
Standard Settings = 2.5+2.0 turns
e Clip position = 2nd from top
Replace cyl. hd. gasket if torn / cut / pressed
Replace cylinder block piston assly if worn out / excessive clearance
Replace cylinder head if spark plug mtg. hole threads washed out
Skill Tip : Ensure cylinder & piston are of the same group while replacing.
Carry out surface facing / Replace cylinder head if warpage is equal to or more than 0.05 mm
Replace cylinder piston assembly if partially seized
OK
Continued.....
Continued.....
151
152

Vehicle pulling to one side 1st Step : Steering Related
If compression pressure in wet test is OK
OK
Continued.....
Check compression pressure. Perform dry & wet compression test
If compression pressure in wet test is NOT OK
Check steering for free movement by rotating handle on either side Not OK
If stg. jam, loosen front fork side bolts, top bolts, steering ring nut & adjust the steering for free movement. Retighten the bolts as per SOP sequence.
Continued from back page
Continued from back page
Piston ring to groove clearance Std Limit

Top Ring : 0.06 mm 0.16 mm
Clean valve guide & valve stem if deposited with gummy substance
Compression Ring End Gap Std Limit
0.15 ~ 0.30 mm 0.50 mm
Service Limit
OK
2nd Step : Chain Adjuster Related Check rear wheel alignment w.r.t. drive chain adjusters Not OK Set both side drive chain adjusters equally
Service Limit
Rectify valve seat & valve face by lapping if pitted / worn out / excess carbon depostion
OK Not OK Check handle bar & upper holder bkt. for alignment
3rd Step : Handle Bar Related Replace handle bar if bent If OK Replace fork upper holder bracket if misaligned
Replace inlet / exhaust valve if bent
OK 4th Step : Fork Inner Pipe Related Not OK Check fork inner pipe & under holder bracket for alignment Replace fork inner pipes if bent If OK Replace fork under holder bracket T if bent OK Continued.....
Inspect De-compression mechanism for stickyness
Piston Standard Diameter Cylinder Standard Diameter A Group B Group 63.508~63.515 63.50~63.508
A Group
B Group
63.478~63.488
63.488~63.498
153
154

Kick lever not returning 1st Step : Kick Lever Assembly Related Replace swing arm if bent Check kick lever assembly for no fouling with silencer, for intact condition If OK Replace kick lever if bent / kick boss resting area worn out / not flat If OK If OK OK Replace frame if mounting hole of swing arm is oblonged Replace kick boss if splines / serrations worn out Not OK Replace kick boss if kick lever resting area worn out / not flat
OK
5th Step : Swing Arm Related
Check swing arm for alignment
Not OK
OK Replace frame if misaligned at steering tube area
6th Step : Frame Alignment Related
Not OK
Check frame for alignment
2nd Step : Kick Shaft Related
Dismantle clutch cover & check kick shaft assembly for Correct timing of ratchet gear w.r.t. kick shaft Return spring tension O.K.
Not OK
Match the dot mark on ratchet gear w.r.t. dot mark on kick shaft end if timing incorrect If OK Engine O/H and Replace kick shaft return spring if weak
OK Not OK Check kick guide screws for tightness and intact condition
3rd Step : Kick Guide Related Tighten kick guide allen bolts by applying loctite 638 if loose If OK Replace kick guide allen bolts if sheared off
OK 4th Step : Crankcase L.H. Related Check crankcase RH kick boss area for intact condition Not OK Replace crankcase RH if cracked at kick boss area
155
156
Clutch slippage OK Not OK Dismantle clutch & check all components for correct dimensions & no abnormal wear If OK 5th Step : Clutch Assembly Related Replace clutch springs if free length is less than standard
1st Step : Clutch Lever Free Play Related Set clutch lever free play as per specifications
Check clutch lever free play
Not OK
Std. Free Play for Clutch Lever
2~3 mm
OK Dismantle, rectify & refit clutch lever if sticky If OK Replace clutch cable if sticky / jam
2nd Step : Clutch Cable Related
Replace friction plates if worn out / burnt / friction bonding given away If OK Replace steel plates if worn out / burnt / glazy If OK Replace clutch center (clutch hub) if worn out If OK Replace clutch wheel if worn out
Not OK
Check clutch lever operation for smooth working
OK Top up engine oil level if less than specified If OK Replace engine oil if viscosity not OK
3rd Step : Engine Oil Related
Check engine oil level and viscosity
Not OK
OK
4th Step : Clutch Release Mech. Related Replace clutch release lever if bent / O.D. oversize If OK Replace clutch cover if release levers parent hole undersize / oval If OK Replace rack & Clutch Release Shaft if teeth worn out / damaged Continued.....
Not OK
Check clutch release mechanism for smooth operation
OK
157
158

OK 5th Step : Rear Damper Rubber Related
Drive chain noise
1st Step : Chain Adjustment Related Adjust slackness as per specification & lubricate the chain by SAE 90 oil Check damper rubbers of rear wheel sprocket for no abnormal wear Not OK
Check drive chain for slackness & lubrication
Not OK
Replace damper rubbers if worn out
Chain Slackness = 30 ~ 35 mm OK Not OK Refit chain covers properly If OK Fit PVC strips if missing If OK 254 ~ 254.6 mm Replace chain cover bolts & washers by O.E. ones if touching to chain If OK Correct alignment of swing arm brackets if bent Std. Limit Dismantle chain sprocket assly. & check for wear & alignment
6th Step : Chain Sprocket Related Align engine sprocket & rear wheel sprockets If OK Replace drive chain if 20 link length is more than service limit If OK Replace chain sprocket kit if worn out
OK
2nd Step : Chain Cover Related
Not OK
Check chain cover for correct fitment & alignment Drive Chain 20 Link Length Ser. Limit 260 mm
OK
3rd Step : Sprocket Mtg. Bolt Related Tighten bolts to specified torque if loose
Check rear wheel sprocket bolts for tightness
Not OK
OK
4th Step : Engine Sprocket Collar Related Carry out sanding operation of collar I.D. & apply SAE 90 oil if collar jam on O/P shaft O.D.
Check output sprocket collar for free rotation
Not OK
OK Continued.....
159
160

OK 5th Step : Muffler Related Check silencer for intact baffle plates
Tighten silencer mouth nuts if loose
Silencer noise
1st Step : Mounting Nuts Related
Check silencer mouth securing nuts for tightness
Not OK
Not OK
Replace silencer if baffle plate / plates are loose
OK 6th Step : Torque Expansion chamber Related Not OK Tighten CO nozzle bolt if loose / replace silencer if nozzle given away
Tightening Torque = 1.4~1.9 Kgm
OK
Check silencer ExhausTEC chamber for no noise
If OK
2nd Step : Gasket Related Replace silencer mouth gasket (gasket exhaust) if pressed
Check silencer mouth gasket for intact condition
Not OK
Replace silencer if noise in ExhausTEC chamber due to paint solidified from inside
OK
3rd Step : Silencer Guard Related
Check silencer guard securing screws / allen bolts for tightness
Not OK
Tighten silencer guard screws / allen bolts if loose. Apply loctite 243.
OK
4th Step : Footrest Fouling Related
Check silencer for bend pipe not fouling with riders foot rest Correct silencer fitment if fouling with riders foot rest
Not OK
OK
Continued.....
161
162

Poor braking - Disc brake system 1st Step : Master Cylinder Related Not OK Check brake fluid in master cylinder for correct level Top-up master cylinder by using DOT-3/DOT-4 brake fluid if fluid level is below minimum mark If OK Identify source of leakage, rectify & top-up leakage if any, if brake fluid level is low prematurely OK 2nd Step : Brake Disc Pad Related 3.5 Kgm 2.5~3.5 Kgm 2.5~3.5 Kgm OK Check disc pads for thickness Not OK Replace disc pads if worn out beyond service limit 0.5 Kgm Check disc pads for surface condition Not OK Clean disc pads by emery paper if found water soaked, oil / grease soaked, glazed
Steering sticky / Jam movement
1st Step : Steering Ring Nut Related
Check steering ring nut & center nut / bolt for correct tightness (No over tightening) Loosen steering center nut / bolt, fork side clamp bolts and fork top bolts, steering ring nut & tighten them in sequence as per S.O.P. to specified torque
Not OK
Tightening Torques in Kgm Torque
Description
Steering center special nut / bolt
OK
Fork side bolts
Fork top bolts
Steering ring nut
2nd Step: Steering Races Fitment Related
Check steering races for correct fitment Refit steering races as per S.O.P. if fitted in tilted condition
Not OK
OK
Disc Pad Lining Thickness Standard Limit Service Limit 7.4 mm 3.8 mm 7.4 mm 3.8 mm 3rd Step : Caliper Related Check oil seal of Caliper piston for intact lip condition Not OK Replace Caliper seals if - seal lips worn out, deformed, became hard.
OK
3rd Step: Stg. Races Condition Related
Check condition of steering races for no pitting marks & steering balls for no rusting / breakage Replace steering races & balls if pitted / rusty respectively
Not OK
OK 4th Step : Brake Disc Related Check brake disc for thickness & alignment Disc Disc Runout Standard Limit Service Limit Less than 0.2 mm 0.2 mm Not OK Replace brake disc if worn out, run out exceeds service limit.
Note : Lubricate steering races and balls by Servo Gem RR-3 grease at every 10,000 Kms.
163
164
Spongy brakes - Disc brake system
1st Step : Master Cylinder Related Top up master cylinder by DOT-3/DOT-4 brake fluid only if fluid level is below minimum mark.
Check brake fluid level in master cylinder
Not OK
OK
2nd Step : Brake Fluid leakage Related Identify source of leakage, rectify & top-up if brake fluid level is below minimum mark
Check brake hose, Caliper and Master cylinder for no leakages.
Not OK
OK
3rd Step : Air Trapping Related Carry out air bleeding of disc brake system as per SOP
Check Disc Brake system free from air trapping.
Not OK
OK Clean master cylinder cover & vent holes if clogged due to oxidation / dust.
4th Step : Master Cylinder Related
Check master cylinder vent holes for no clogging.
Not OK
OK
Check master cylinder diaphragm for no deformation teared off Replace diaphragm by new one if deformed / torn.
Not OK
OK Replace primary seal of master cylinder if worn out.
Check master cylinder primary seal for no wear.
Not OK
OK
4th Step : Caliper Related Clean & Lubricate caliper pins by silicon grease / brake fluid if jam.
Check for free floating movement of Caliper.
Not OK
165

Pulsar DTSi Service Manual

Uploaded by

Copyright:

Available Formats

Pulsar DTSi Service Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Pulsar DTSi Service Manual

Uploaded by

Copyright:

Available Formats

Identification Data Salient Features

Refined engine power delivery by optimization of Exhaus TEC

Convenience and Comfort

Self-canceling indicators After completion of turn, the indicator

5. Hall Sensor for Indicator

2. LCD Speedo Console

6. Vehicle Speed Sensor

Self check provision for Tachometer for its functioning

4. Body Control Unit

8. Tail Light LED display

(Placed inside Head Light fairing)

Pulsar DTS-i UG-III-180cc Training Notes

Dealer Development Center

Dealer Development Center

Pulsar DTS-i UG-III-180cc Training Notes

High RPM warning lamp

Engine cut-off at 10000 RPM Spark gets cut-off at 10000 RPM

to bring down the engines RPM for safety.

CHASSIS & BODY

Pulsar DTS-i UG-III-180cc Training Notes

Dealer Development Center

Dealer Development Center

Pulsar DTS-i UG-III-180cc Training Notes

Frequently Asked Questions (FAQs)

Fuel Tank Capacity

3.2 liters Reserve

2.0 liters Usable reserve

Twist grip type on RH side of handle bar

Left foot pedal operated

Lever operated on LH side of handle bar

Lever operated on RH side of handle bar

Pedal operated by right foot

1990 750 1090 1320 2180 165

Vehicle kerb weight Gross vehicle weight

143 kg. 273 Kg.

Maximum speed Climbing ability

125 km/h with single rider (68kg) 28% (160 Maximum)

How does the digital Speedo work?

All dimensions are under UNLADEN condition.

Definitions of terminologies wherever applicable are as per relevant IS/ISO standards.

Specifications are subject to change without notice.

Pulsar DTS-i UG-III-180cc Training Notes

Dealer Development Center

Dealer Development Center

Pulsar DTS-i UG-III-180cc Training Notes

Frequently Asked Questions (FAQs)

Frequently Asked Questions (FAQs)

Why two trip meter reading option is given? How is it useful?

This is an added advantage taken from digital technology! B B

What do Self-canceling Indicators switches means?

Pulsar DTS-i UG-III-180cc Training Notes

Dealer Development Center

Dealer Development Center

Pulsar DTS-i UG-III-180cc Training Notes

Frequently Asked Questions (FAQs)

Pre Delivery Inspection Checklist

What is that disabling of cranking after 3 successive attempts?

Are these type of product features available in Pulsar150cc also?

Pulsar DTS-i UG-III-180cc Training Notes

Dealer Development Center