Diamond Owners Manual 109
Diamond Owners Manual 109
Diamond Owners Manual 109
by Meyer
Out-Front-Electric Hydraulics
Owners Manual
Diamond Snowplows
Table of Contents Page Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Tripedge Series Get to Know Your Diamond MDII Snowplow . . . . . 3-6 Get to Know Your Diamond Snowplow . . . . . . . . . . 7-8 Blade Specifications . . . . . . . . . . . . . . . . . . . . . . . 9-10 Controls & Operating Instructions . . . . . . . . . . . . 11-12 Diamond MDII Snow Plow Instructions . . . . . . . . . .13-16 Snowplow Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Removing & Attaching Snowplow . . . . . . . . . . . . . . . . 17 General Maintenance & Adjustments . . . . . . . . . . . 18-19 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-22 Efficient Snow Clearance . . . . . . . . . . . . . . . . . . . . . . . 23 Keep Snow Under Control . . . . . . . . . . . . . . . . . . . . . . 23 Selecting Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Hourly Snow Clearing Capacities . . . . . . . . . . . . . . . . 24 Plow with the Storm . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Establishing Snow Clearance Plans . . . . . . . . . . . . . . 26 Snowplowing Tips from the Pros . . . . . . . . . . . . . . 27-29 Minerals and Chemicals for Ice Control . . . . . . . . . . . 30 Ice Control Spreaders . . . . . . . . . . . . . . . . . . . . . . . 31-32 Fast Moving Parts List . . . . . . . . . . . . . . . . . . . . . . 33-34 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35-36 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-38 Warranty Card . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
Introduction
Snow, despite the beauty it may impart to a bleak winter landscape, poses the dual threat of inconvenience and danger. The environmental conditions associated with snow, not to mention the health hazards and economic loss it may impose, seriously endanger thousands of lives annually. Business and industry suffer, and millions of snowbelt residents may be affected by a single snowstorm. Diamond Equipment has published this manual to help you get maximum performance from your Diamond Snowplow and familiarize you with the features designed for efficiency and safety; be sure you recognize and understand them. Follow recommended operation and maintenance instructions, so when the storm hits, your Diamond Snowplow will be ready and you will know how to plow like a pro. Do not equip any vehicle with a snowplow without consulting manufacturer's recommendations. Vehicles with Diamond Snowplows installed may be so equipped as to meet vehicle manufacturers' specifications and recommended options for snowplowing use. Most vehicle manufacturers insist that vehicles which are to be used for snowplowing be equipped with certain options and accessories, and it is so stated in vehicle manufacturer specifications for snowplow application. WARNING: Deployment of an air bag while using a Diamond snowplow will not be covered under Diamond Equipment warranty. We also recommend that, for optimum performance, vehicles used for snowplowing be equipped with: Four-Wheel Drive Minimum 60 Amp Alternator or larger Minimum 70 Amp Battery or larger (550 C.C.A.) Mud and Snow Tires Increased Radiator Cooling Automatic Transmission Transmission Cooler Power Brakes Power Steering
Under the continuing Diamond Product Improvement Plan, Diamond Equipment reserves the right to change design details and construction without prior notice and without incurring any obligation.
Diamond snowplow equipment should only be used on vehicles equipped with the manufacturers snowplow preparation packages. Snowplowing without the original snowplow preparation package may damage your vehicle and the added weight of the equipment may impair the operation and control of the vehicle. Snowplowing with a vehicle that the manufacturer does not recommend for that purpose may void your new vehicle warranty. If your vehicle is not originally equipped with the snowplow preparation package, additional equipment may be necessary before snowplowing. Owners of these vehicles should consult their truck dealer before purchase or installation of equipment. CAUTION: The installation, on any vehicle, of these parts is not a full substitute for the original equipment snowplow preparation package.
CRANKSTAND STORAGE To store Crankstand on the Lift Frame slide the tube that is attached to the side of the Crankstand over the receiver tube on the driver's side of the Lift Frame. Insert the chain locking pin through the vertical holes on both the tubes. Note: Crankstand should always be fully retracted (up) and be pinned in the vertical transport position when not In use. Receiver Tube Cap may be placed over the driver side transport tube while the Crankstand is in use on the A-Frame. The Receiver Tube Cap may also be switched over to the Adjustment Tube of the A-Frame when the Crankstand is mounted to the Lift Frame. Storage of the Crankstand is the responsibility of the operator. The stand can be stored on the lift frame in the retracted position to the driver's side transport tube or inside the vehicle cab. HYDRAULIC COVER Install Black Hydraulic Cover before installing the Lift Assembly to the Lift Frame. Begin by sliding the Hydraulic Cover down over the Lift Ram. Slide the side covering the motor carefully over the motor, do not force or stretch the Hydraulic Cover; it will fit comfortably over all parts of the Hydraulic Unit. Feed the three coil wires (red, green and black) through the hole located on backside of cover. Route coupler weather plugs through holes in cover where power angling hoses enter. Snap Cover together. Caution: Care should be taken with the installation and or removal of the Hydraulic Cover, including partial removal when repairs are performed on the Hydraulic Lift Unit. Tearing of the Hydraulic Cover for any reason will not be covered under the Diamond Warranty.
ATTACHING MOLDBOARD ASSEMBLY ONLY Attach A-Frame to Lift Frame by connecting Crankstand to the adjustment tube in the center of the A-Frame Frame. Insert the chained locking pin all the way through the vertical holes on both the tubes. Crank up A-Frame until the holes on the back ears of the AFrame are about 12 off the ground. Pull out the Yellow Handle Pins on both sides of the Lift Frame. Twist handle slightly to the right or left disengaging the pin. Pull truck up to the A-Frame / Moldboard assembly aligning the A-Frame ears between the two lift frame plates until contact is made with the Clevis Frame. Once you feel contact, push the moldboard assembly a few inches forward, this insures proper alignment so that the A-Frame is square to the Clevis Frame. Adjust the Crankstand up until the front of the truck raises slightly. Rotate the Yellow Handled Pins so that the small leg realigns with the slot, engaging the pin. The spring loaded pin should snap into place locking the A-Frame to the lift frame. Note: If pins do not properly engage move the truck slightly forward a few more inches and/or adjust (raise or lower) the Crankstand until pins lock into place. If only one pin should engage, retract the stand to the full upright position. Remove the Crankstand from the A-frame by removing the chained locking pin. Reattach the Crankstand to the transport tube on the driver's side of the Lift Frame in the vertical transport position. Attach the Lift Chain to the Lift Arm through the two hooks on the lift arm. Adjust the lift chain at the lift arm so that there are 2-3 links of slack. This ensures that the plow blade will lift fully and be able to follow the ground contour while plowing. Raise the plow with the hydraulics and swing the moldboard slightly left or right until the pin engages.
DETACHING THE COMPLETE ASSEMBLY Leave control switch in lower float position and push down on the Lift Arm. Disconnect the electrical plug and slip on weather caps over both ends. Attach Crankstand to the adjustment tube in the center of the A Frame using the chained locking pin. Caution: Crankstand must be secured at all times. Adjust the Crankstand down until the bottom of stand touches the ground. Pull and twist the two rear Blue Handle Pins to disengage. Next pull and twist the two front Blue Handle Pins to disengage. If the pins do not pull easily, adjust stand up or down slightly to remove tension on the pins until they disengage. At this time the lift frame should be leaning forward slightly, at rest on the top of the Crankstand. Pull truck away. DETACHING MOLDBOARD ASSEMBLY ONLY Leave control switch in lower float position and push down on the Lift Arm. Disconnect hydraulic couplers and Lift Chain from Lift Arm. Attach Crankstand to the adjustment tube in the center of the AFrame using the chained locking pin. Caution: Crankstand must be secured at all times. Adjust the Crankstand down until the bottom of stand touches the ground. Pull and twist the Yellow Handled Pins to disengage. If the pins do not pull easily, adjust stand up or down slightly to remove tension on the pins until they disengage. Pull truck away. ATTACHING THE COMPLETE ASSEMBLY Check that all four Blue Handle Pins are disengaged. Drive the truck up to the MDII assembly centering the hood of the truck to the lift arm to assure proper alignment with lift frame guide plates until contact is made. Once contact is made drive forward, pushing the assembly a few inches. This insures the A-Frame is square to the Clevis Frame for proper pin attachment. Adjust the Crankstand up
until the front of the truck raises slightly. The rear Blue Handle Pins should now be aligned with the rear holes on the clevis frame. Twist all Blue Handle Pins so that the small leg re-aligns with the slot, engaging the pins. The rear spring loaded pins should snap into place. Note: If pins do not lock immediately the A-Frame is not square to the Clevis Frame. Move truck slightly forward and/or adjust the Crankstand up or down until rear pins engage. Once the back pins are locked push the top of the Lift Frame towards the truck locking the front pins to the clevis frame. Remove the Crankstand from the A-frame by removing the chained locking pin. Reattach the Crankstand to the transport tube on the driver's side of the Lift Frame in the vertical, retracted position. Caution: Crankstand must be secured at all times. Reattach the one step electrical connection.
12
MDII Mounting System
E-57H 10 E-60H 9 11
8 14 13
5 6 3
4
8
TRIPEDGE SERIES Model 7.5 For 1/2 and 3/4 ton 4x4 Standard Duty Pickups and Sport Utility Vehicles
TRIPEDGE SERIES Models 8.0, 8.5, 9.0 For 3/4 and One Ton 4x4 Standard Duty Pickups and Cab-Chassis Vehicles
2 x 12
2 x 12
10
11
TRIP-EDGE
Fig. 2
12
Diamond
Snowplow Instructions
13
14
15
16
Snowplow Operation
The snowplow should only be in operation when the vehicle ignition switch and the Electro-Touch control switch are in the "ON" position. Care should be taken to insure that the ElectroTouch control switch is kept dry and free from moisture during normal operation. When the Electro-Touch control switch is turned "On," yellow lights illuminate the location of the individual touch pads for the functions of the snowplow: (Up), (Angle Left), (Angle Right), and (Down). Lowering of the snowplow an inch at a time is possible by tapping the down arrow in short intervals. Holding down the down arrow will activate a green light located in the upper left corner of the Electro-Touch switch. This green light indicates the snowplow is now in the Lower/Float position. In this position the snowplow will be able to follow the contour of the road and the snowplow can also be angled to the left or right. Touching the up arrow automatically cancels the Lower/Float position. This switch is short circuit and temperature protected. All wire connections must be securely plugged together. If any of these conditions exist, the red overload LED will light. The overload LED (red light) is located in the upper left corner below the float light of the Electro-Touch switch. Reset is accomplished by turning off the ignition switch or by turning the power switch off momentarily and then back on. If an overheating temperature condition exists, it will be necessary to allow the unit to cool down for approximately 2 minutes. If the overload light is still illuminated after attempts to reset the switch have failed, contact your nearest authorized Diamond Distributor for repairs. Note: On Model E-60 only to regulate the lower speed, locate the lower adj. screw on page 19, Fig. 0-3. Turn adj. screw in to slow down or out for faster lower speed. Adjustments must be made with moldboard on the ground. This feature is not available on model E-57. CAUTION: When the snowplow is not in operation, the Electro-Touch Control Switch should be in the "OFF" position.
Over-the-Road Operation
Based on the experience of our representatives and other background, we advise a maximum transporting speed of 40 m.p.h. or locally regulated speeds, which ever is less, dependent upon road conditions. The operators should, of course, maintain a safe stopping distance and adequate passing clearance at all times. When transporting the snowplow to avoid engine overheating, angle the moldboard completely, carrying it as low as permitted for safety by road and surface conditions.
ADJUSTING CHAIN FOR PROPER SLACK WHEN PLOWING SNOW 1. Be sure moldboard is on ground and pushframe is reattached at proper hole in front mounting frame. 2. Be sure lift piston is fully retracted. 3. Hold chains taut and choose the third link above lift arm, place that link in lift arm locking groove. This procedure will provide the proper amount of slack when snowplowing for the moldboard to follow the contour of the ground. You may wish to mark these links with paint or tape for easy identification. Due to the differences in vehicle ride heights, extra chain links may vary in length.
17
General Maintenance
Diamond Equipment recommends this maintenance information for regular service. Sustained heavy operation may call for more frequent service. Snowplowing subjects a vehicle to exceptionally rugged use. As a result, it is important to inspect and bring the snowplow and vehicle up to maximum operating conditions. Inspection should be made of both the vehicle and snowplow prior to the plowing season and after each use.
Pre-Season Maintenance
Scheduled vehicle maintenance should be performed as recommended by the manufacturer. Don't forget that in addition to keeping equipment in order: 1. Keep windshield wipers, heaters and lights working. 2. Diamond offers as standard equipment quartz halogen snowplow lights for even brighter illumination. 3. Equip vehicles with chains where necessary. 4. Provide operators with protective clothing and with rubber gloves for handling snow melting chemicals. VEHICLE ELECTRICAL SYSTEMFor maximum efficiency, the vehicle supporting the snowplow must be properly serviced. The system should consist of at least a 70 amp/hr. battery and a 60 amp alternator. Be sure to check regularly: 1. Battery terminals to assure they're clean and free of corrosion. 2. Electrical connections, to assure they're tight and corrosion-free. Taping may be called for. All wires must be held clear of moving or hot engine parts or sharp sheet metal. 3. Battery must be in top operating condition. 4. Alternator and regulator, to assure maximum electrical output.
SNOWPLOW NOTE: ALWAYS lower moldboard to ground when vehicle is not in use. Check the Troubleshooting Chart, pages 20-22, and Post Season Maintenance, page 19, for advice on maintaining the unit. 1. Check and maintain hydraulic fluid reservoir level to 1 " - 1 1/2" from top cap. (Lift cylinder in down position.) 2. Check entire hydraulic system for leaks. A significant drop in hydraulic fluid level is evidence of a leak which must be corrected to prevent serious damage. See page 19 3. Before and after each season, remove sector pivot pins, thoroughly grease pivot tubes and reinstall pins. Lubricate all pivot points with chassis lube. 4. ADJUSTING TRIP SPRING TENSION - Tighten adjustment nut to the point when spring coils begin to separate. Tighten bottom locknut to hold in place. 5. WEAR SHOES A. Inspect moldboard wear shoes for wear and height adjustment. B. Always replace wear shoes as soon as they start to wear through. C. Adjust the wear shoes to maintain cutting edge height of 1/2" above ground in snowplowing position. (Can be set higher when used on gravel driveways. 6. CUTTING EDGE Replace the cutting edge before it wears to the attaching bolts. This will prevent permanent damage to the trip edge. 7. MOUNTING BOLTS Retighten all mounting bolts after first snowplowing session and at regular intervals through the season. 8. SNO-FLO PAINT At the beginning and end of each season, remove any accumulated rust, then paint the moldboard surface with Meyer Sno-Flo paint to inhibit rust formation. Touch-up paint is also available in aerosol cansboth Sno Flo yellow and black.
18
NOTE: PROTECTION AGAINST RUST AND CORROSION When the power unit is not used for extended periods, protect the chromed lift piston fully extending and coating it with chassis lubricant. Coat the exposed portions of the power angling cylinder rods with chassis lubricant to protect against corrosion.
2. 3.
SNOWPLOW STORAGE 1. When snowplow is disconnected, extend lift cylinder to end of stroke and coat chrome rod with light grease. This fills the cylinder with hydraulic fluid and protects the interior and exterior from rust and corrosion. 2. Whenever Moldboard is disconnected, coat the exposed portions of the power angling cylinder chrome rods with light grease to protect them from corrosion. 3. Be sure to reconnect quick couplers to keep them clean and prevent contamination of the system. 4. Coat all pivot pins and other wear points with chassis lubricant. 5. Unplug all electrical connections at power unit. Coat all connections with a dielectric compound to prevent corrosion and plug into their corresponding weather plugs. Unplug the snowplow lights, tape or use a dielectric compound at light connections to prevent corrosion. 6. Remove PULL-AWAY lift frame module from vehicle. Liberally coat insides of frame receiver tubes and ends of lift frame with chassis grease/anti-seize lubricant. Protect frame receiver tubes from dirt and other types of contamination by installing the receiver tube caps when the lift frame is removed from the vehicle 7. WARNING: Lift arm extends beyond bumper of vehicle. To minimize damage from a front-end collision, lift arm should be removed from vehicle when snowplow is removed.
Filler Hole and Relief Valve Pressure Relief Valve Grounding Point B Solenoid (red wire) C Solenoid (green wire) A Solenoid (black wire) Cross-over Relief Valve
4.
E-60H E-57H
Motor Right Angle Lower Adjustment Angle Left
FIGURE 0-3
19
GENERAL INFORMATION
Before any troubleshooting is started, make certain the following conditions are met. 1. The moldboard is pointing straight ahead. This can often be done by coupling the hose from the left cylinder into the right cylinder and pushing the snowplow by hand. 2. The power angling cylinders must be installed correctly. The left cylinder has a hose with a male half of a coupler attached while the right cylinder only has the female half of a coupler attached. Reverse them if installed on wrong side. 3. The solenoid coils must be on their proper valve. The "C"- coil (green wire) must be located on the valve closest to the power angling hoses. The "B"-coil (red wire) is positioned on the valve furthest from the power angling hoses. The A coil (black wire) is smaller in diameter and is easily located on the E-60 power unit. On the E-57 power unit, the "A" coil (black wire) is located on the back side of the unit. 4. The electrical installation must have been made according to instructions supplied by Diamond Equipment.
TESTING TIPS
Many tests do not require removing the Power Unit from the vehicle. However, more thorough testing can be done by using the Meyer Test Stand which allows direct pressure and Amperage readings. 1. Use a screwdriver or other small tool to check for magnetism of solenoid coils A, B & "C". Place the tool on the nut securing the coil and have an assistant operate the switch. You should feel strong magnetic attraction. 2. Use a test light or volt meter to determine whether there is power at harness or switches. 3. When determining Ampere draw of motor, always obtain the highest value possible, i.e., at maximum raise or angle with motor running. 4. Proper rotation for motor is indicated by an arrow on the top of the E-57 pump. 5. The pump shaft (all models) of a good pump can be turned smoothly using two fingers. If it can't be turned easily, the pump is too tight and must be replaced. 6. Pump pressure can be measured at an angle hose (note pressure at full angle) or in the pressure filter port (an adapter is necessary for the filter port). (See Figure 0-3.) 7. If hydraulic system is contaminated it is recommended that the hydraulic unit, power angling rams and hoses be drained and flushed clean. The system should then be refilled with Meyer M-1 oil. See pages 18-19.
20
CONDITION
Plow does not lift or lifts slowly- motor operates.
POSSIBLE CAUSE
1. 2. 3. 4. 5. 6. 7. 1. 2. 3. 4. 5. 6. 7. 1. 2. 3. 4. Low hydraulic fluid level Discharged battery. Leaking or open A cartridge. No current to B coil. (red wire) Inoperative B coil. (red wire) Malfunctioning motor. Malfunctioning pump. Improper coupler engagement. Mechanical bind or interference. Malfunctioning coupler. No current to C coil. (green wire) Inoperative C coil. (green wire) Inoperative C cartridge. Leaking or open crossover relief valve. Improper coupler engagement. Mechanical bind or interference. Malfunctioning coupler. Leaking or open crossover relief valve.
CORRECTION
1. 2. 3. 4. 5. 6. 7. 1. 2. 3. 4. 5. 6. 7. 1. 2. 3. 4. Add fluid to proper level. Recharge battery. Clean or replace A cartridge. Locate malfunction and repair. Replace B coil. (red wire) Repair or replace motor. Replace pump. Engage coupler properly. Eliminate mechanical bind or interference. Repair or replace coupler. Locate malfunction and repair. Replace C coil. (green wire) Clean or replace C cartridge. Clean or replace crossover relief valve. Engage coupler properly. Eliminate mechanical bind or interference. Repair or replace coupler. Clean or replace crossover relief valve.
1. Improper coupler engagement. 2. Mechanical bind or interference. 3. Leaking or open crossover relief valve.
1. Engage coupler properly. 2. Eliminate mechanical bind or interference. 3. Clean or replace crossover relief valve.
21
MODEL
All Power Angling Models
CONDITION
Plow will not hold in angled position.
POSSIBLE CAUSE
1. Air in cylinders and hoses. 2. 3. 4. 5. Leaking C cartridge O-rings. Leaking or open pilot check valve. Leaking crossover relief valve. Crossover relief valve opening at too low a pressure. Discharged or defective battery. Loose or corroded electrical connections. Inoperative starter solenoid. Malfunctioning control switch. Malfunctioning motor.
CORRECTION
1. Bleed cylinders and hoses. Tighten P.A. cylinder gland nut. 2. Replace O-rings. 3. Clean or replace pilot check valve. 4. Clean or replace crossover relief valve. 5. Replace crossover relief valve.
1. 2. 3. 4. 5.
1. 2. 3. 4. 5.
Recharge or replace battery. Clean and tighten electrical connections. Replace starter solenoid. Replace control switch. Repair or replace motor.
1. No current to A coil. (black wire) 2. A cartridge jammed in closed position. 3. Inoperative A coil. (black wire)
1. Locate malfunction and repair. 2. Clean or replace A cartridge. 3. Replace A coil. (black wire)
1. 2. 3. 4. 5.
A cartridge. A cartridge O-ring. B check valve. ram packing cup. O-ring at bottom of lift cylinder.
1 Clean or replace A cartridge. 2. Replace O-ring. 3. Clean or replace B check valve. 4. Replace ram packing cup. 5. Replace O-ring.
22
23
SELECTING EQUIPMENT
Where you plan to plow, and the conditions under which you will be plowing, determine to a great extent the type of vehicle you'll find most useful. In general, three types of vehicles are available as the power source of snow clearance. Each type has certain inherent advantages depending upon the particular situation. Four-wheel drive UTILITY VEHICLES and TRUCKS have proven most effective in general snowplowing situations. They have excellent traction and maneuverability and are extremely easy to handle. Two-wheel drive TRUCKS, particularly those of 1 1/2 to 3 tons, are best for straight line road clearance and in large open areas. TRACTORS are effective for trapped areas in which visibility is limited, plus a rear grader blade can be used in conjunction with the Diamond Snowplow. Diamond Snowplow's custom design for specific vehicles provides the advantage of easy, fast attaching and detaching. This feature permits utilization of vehicle versatility as weather conditions and job requirements demand. 20 m.p.h. is a maximum snowplowing speed under ideal conditions, assuming the driver is familiar with the roadway or area to be cleared. Under unfamiliar or hazardous conditions, or if there is poor visibility, we recommend reduced speed and extreme caution.
Careful analysis of the area you intend to clear of snow will direct you to the types of equipment you'll require. Check Table 1, Average Hourly Snow Clearing Capacities, for recommended equipment depending upon the area in which you'll be working. Then, match the vehicles you already have with the snow removal equipment you need. If your vehicles do not have the capacity to clear all major access areas within two hours, you should increase clearing capacity with additional equipment or arrange for assistance through a contract plowing service.
Based upon regional interviews with knowledgeable contractors (6" snowfall cleared by operators with average ability). ** Based upon recommended maximum plowing speed of 20 mph. ~ Not recommended for use, except in very large areas of this type. Use 1 1/2 ton figures if necessary.
24
Angle Moldboard for Optimum Results. You will not be able to plow snow of any significant depth straight ahead for more than a short distance. Set the moldboard at the best angle for rolling snow sideways in the desired direction. The snowplow path, in the angled position, should exceed the tire track by at least six inches on either side. Be sure to have enough slack in the lift chain while plowing so the cutting edge of the moldboard can follow the ground contour. Use the adjustable runner shoes to set the bottom edge of the plow just above the ground for best operation. It's important to recognize the significance of even a few inches of snow. Besides being slippery, especially when wet, snow can be extraordinarily heavy, and make auto travel impossible. Snowfall of just 1 to 3 inches will produce hazardous traffic and roadway conditions even for experienced drivers. Snow is heaviest when wet, and most difficult to handle. The National Weather Service reports that a 6-inch, average weight snowfall on a 200 x 200 foot parking lot weighs 62 tons. Heavy, wet snow for the same area might weigh as much as 248 tons. If the heavy snow had to be hauled away, you'd need 74 full loads on a 10-yard truck. Obviously, the only way to assure clear traffic areas is to be prepared with the proper equipment and expertise to open arteries and areas to traffic. Remember to keep current with accurate snowfall information from local weather bureaus via radio and television.
25
2.
26
27
STRAIGHT LINE SNOWPLOWING This method is most efficient for drives, streets, roads and walkways. Moldboard type blade snowplows mounted on utility vehicles or service trucks are best for such an operation. Set the snowplow moldboard at an angle so that the snow is rolled to the shoulder or curb. Single lane walks, roads and aisles can often be cleared with one pass. When the road is more than twice the moldboard's width, plow a center lane for the first full pass. Then, in follow-up passes, work the snow to the sides. The diagram illustrates plowing sequence for a typical 20-foot road. Corner clearing is almost automatic when clearing intersecting streets. When snow is heavy, a little "stop over" snow may have to be removed from intersections by additional short passes. We recommend a speed of 5 to 15 MPH for this kind of plowing. Of course, road surface, weather conditions and equipment will influence your speed. Plow with the storm.
WIDE DRIVEWAY 1. Make one pass down center with blade in straight position. 2. Push snow to side with moldboard angled. 3. Do the same on either side.
28
DRIVEWAYS
1. Plow toward garage pushing snow to one side. 2. Set blade to straight position, lift it as high as possible and drive through snow to garage. Drop blade and back drag to street. 3. Back into driveway and angle blade again. Use as many passes as necessary to clear drive.
STACKING
When snow clearance conditions are perfect, snow can be merely pushed out of the way to unused areas. The first storm of the season, plow back from the drive area to allow space to pile future snowfall. It is usually necessary to pile snow up to considerable heights. In that case, push the snow forward and upward by raising the snowplow as you move into the pile. The vehicle's momentum will carry the plow into the pile, avoiding equipment damage. The pile should slope outward, so later snows can be pushed upward. WARNING: Stacking snow or pushing up into high snow piles with the plow in Lower/Float or Angled position can cause damage to the Snow Plow components or the vehicle that will not be covered under the Diamond Equipment Warranty Program. Such damage may include, without limitation, twisting the A-Frame, the Moldboard hitting the Lift Arm, or the Plow Markers striking the vehicle.
29
30
31
32
TRIPEDGE PARTS
811000 003 001 811000 003 002 811000 003 003 811000 003 008 811000 005 811000 011 811000 095 811000 161 811000162 811000163 TRIPEDGE PIN TRIPEDGE PIN UPPER PIVOT PIN LOWER PIVOT PIN TRIP SPRING (OLD) WEAR SHOE PLOW MARKER PLOW MARKER TIP TRIPEDGE SPRING (LT) TRIPEDGE SPRING (RT)
33
TWO METER A-FRAME 13594 TM A-FRAME 10888 TM A-FRAME JEEP XJ A-FRAMES FOR HM-10.0 13604 H.M.B.F. 31 X 28 13606 H.M.B.A. 31 X 23 MDII A FRAMES 13711 MDII (11) 34 X 22 1/4 13715 MDII (15) 31 X 22 1/4 PIVOT BARS / SECTORS 12984 TM PIVOT BAR 10891 TM PIVOT BAR JEEP XJ 12793 SECTOR HM - 10.0 POWER ANGLING CYLINDERS 05810 1 1/2 X 10 TM SERIES 05752 2 X 12 HM SERIES ANGLING CYLINDER SEAL KITS 07705 1 1/2 CYLINDER (OMCO) 07831 1 1/2 CYLINDER (MONARCH) 07799 2 CYLINDER HOSE AND HOSE FITTINGS 22291 MALE COUPLER 1/4 HOSE END 22292 FEMALE COUPLER 1/4 HOSE END 21855 SWIVEL ELL 21856 45 DEGREE HOSE W/SWIVEL 22857 FITTING (TALL) 22144 HOSE ASSY. 194 X 45 15741 COUPLER COUPLER LOW SPILL HOSE END KIT - 15846 22291 MALE COUPLER 1/4 HOSE END 22292 FEMALE COUPLER 1/4 HOSE END DRIVER SIDE (LEFT) KIT - 15847 22291 MALE COUPLER 1/4 HOSE END 22294 FEMALE END 3/4-16 VALVE BLOCK SIDE PASSENGER SIDE (RIGHT) KIT - 15848 22292 FEMALE COUPLER 1/4 HOSE END 22293 MALE COUPLER 3/4-16 VALVE BLOCK SIDE
DRIVER/PASSENGER COUPLER SETS - 15876 15847 DRIVER SIDE (LEFT) KIT 15848 PASSENGER SIDE (RIGHT) KIT SNOW DEFLECTOR KITS (POLYETHYLENE) FOR STEEL MOLDBOARDS 12036 6.0 FT. LG 12037 6.5 FT. LG 12038 7.0 FT. LG 12042 9.0 FT. LG 12043 10.0 FT. LG FOR POLY MAX MOLDBOARDS 12045 6.5 FT. LG 12046 7.0 FT. LG ELECTRO-LIFT UNITS 15864 E-57H UNIT ONLY 15867 E-57 H UNIT ONLY MDII 15715 E-60 UNIT ONLY 15720 E-60H UNIT OLY 15756 E-60H UNIT ONLY - MDII CONVERSION KITS E-46 TO E-47 15532S TM-6.5 15535S HM-9.0 / HM-10.0 ELECTRO-LIFT UNITS (SEAL KITS) 15254 E-57 SEAL KIT 15456 E-57 15705 E-60/E-60H MASTER SEAL KIT 15707 E-60, E60H SEAL KIT MISC. LIFT PARTS 08594 QUICK DISCONNECT 15727 MOTOR E-60 (E-57) 15728 BRUSH KIT - FENNER 15889 PUMP ASSEMBLY - E-57 15729 PUMP ASSEMBLY - E-60 15573 BASE & STRNR. ASSY - E-57 15726 SUMP BASE ASSY. E-60 15730 COVER MTR. MOUNT E60 - E-57 15194 TOP CAP ASSY - 60H
MISC. LIFT PARTS (CONTD.) 15738 TOP CAP ASSY. - E-60 15356 A SOLENOID ASSY. - 3/8 STEM 15392 A COIL - 3/8 STEM 15393 A VALVE - 3/8 STEM 15661 A SOLENOID ASSY. 9*16 STEM 15659 A COIL - 9/16 STEM 15660 A VALVE - 9/16 STEM 15357 B SOLENOID ASSY. E-57 15380 B VLAVE E-57 15697 B SOLENOID ASSY. - E-60 15698 B VALVEE-60 15382 B COIL - E-47/E-60 (RED WIRE) 15358 C SOLENOID ASSY. - E-57 E-60 15430 C COIL - E57/E-60 (GREEN WIRE) 15381 C VALVE - E-57/E-60 15370 MOTOR SOLENOID SWITCHES 83001 MEMBRANE SWITCH W/HARN. 80115 MEMBRANDE SWITCH 15753 HARNESS 08574 SINGLE LEVER - COMP. KIT 22092 SWITCH ONLY 15680 HARNESS 08583 FLOOR MOUNT BRACKET 15346 HDWE. BAG W/SWITCHES E-57 21919 LIFT SWITCH 0 E-57 21918 ANGLE SWITCH - E-57 15375 YELLOW HANDLE EXTENSION 15376 BLACK HANDLE EXTENSION RECEIVER TUBE CAP KITS 08673 3 O.D. PIPE 08649 2-7/8 O.D. PIPE 08648 2-1/4 O.D. PIPE HYDRAULIC FLUID 15134 M-1 FLUID QUART 15487 M-1 FLUID 12QT. CASE
LIGHTS- 07223 07224 PLOW LIGHT-PASSENGER 07225 PLOW LIGHT-DRIVER 07116 CONTROL MODULE 07118 C HARNESS 07119 ROCKER SWITCH PAINT TOUCH UP 07026 BLACK AEROSOL (1) 08676 BLACK AEROSOL (2) 07027 SNO-FLO AEROSOL (1) YE 08677 SNO-FLO AEROSOL (12) YE 07028 SNO-FLO BRUSH-ON .6 OZ. (1) YE 08678 SNO-FLO BRUSH-ON .6 OZ. (12) YE 07066 SNO-FLO - QT. (12) YE SINGLE HARNESS PLUB ASSEMBLY 07240 LUG ASSEMBLY 22261 MALE PLUG (VEHICLE SIDE) 22262 FEMALE SOCKET (HYD. SIDE) 22263 WEATHER COVER HYDRAULIC UNIT COVERS 80423 E60H (DUAL TERMINAL MOTOR 80431 E-57 80394 E60H (1 TERM.)
34
ACCESSORIES
M1 HYDRAULIC FLUID
Keep your Diamond Quik-Lift snowplow control system operating at peak performance; change hydraulic fluid yearly. Meyer M1 Hydraulic Fluid has additives that insure peak efficient operation of all Meyer and Diamond electric hydraulic power units.
ELECTRO-TOUCH
The ultimate for snowplow control. You can convert to this great new Electro-Touch control system. This control pad can easily be placed in a variety of locations and the directional buttons are illuminated for night operations.
SLIK-STIK
The Slik-Stik single lever control offers you a choice of 4 mounting locations: on the floor shift selector, on the steering column shift selector, on the dash right or left, on the floor pedestal or console.
EZ-GARD
The EZ-Gard is designed to slide into the Diamond PullAway receiver tubes when the snow plow is removed. Its quick, its easy, and no tools are required. The clean, simple design doesnt overpower the appearance of your vehicle. It just gives it a powerful look!
35
NOTES
36
SPECIFICATIONS
E-60 - E-60H QUIK LIFT POWER UNITS
TORQUE SPECIFICATIONS
Thread Size 5/16 - 24 3/8 - 16 5/16 5/16 1/49/16 18 16 20 18 Torque (in Lbs.) 100 - 125 180 - 220 95 - 105 96 - 120 60 -72 75 -85 NOTE: 1 Quart = 32 Fluid Ounces Model E-60 Unit Hoses & 1-1/2" x 10" Cylinders TOTAL Model E-60 Unit Hoses & 1-1/2" x 12" Cylinders TOTAL Model E-60H Unit Hoses & 1-1/2" x 10" Cylinders (Black) TOTAL Model E-60H Unit Hoses & 2" x 12" Cylinders TOTAL
Reservoir Cover Retaining Nuts Pump Assembly Bolts End Plate of Valve Block Retaining Cap Screws Cover Motor Mounting Motor Drain and Filter Plugs
HYDRAULIC SPECIFICATIONS
PUMP Pressure Output (pump relief valve setting) CROSSOVER RELIEF VALVE Opening Pressure
2500 50 P.S.I.
37
SPECIFICATIONS
E-57H ELECTRO-LIFT POWER UNITS
TORQUE SPECIFICATIONS
Thread Size 5/16 - 24 5/16 - 24 5/16 - 18 1/4 - 20 1/2 - 20 Torque (in Lbs.) 100 - 125 100 - 125 95 - 105 45 -55 75 - 85 HYDRAULIC FLUID CAPACITY NOTE: 1 Quart = 32 Fluid Ounces Model E-57H Unit Hoses & 2" x 12" Cylinders TOTAL
Reservoir Cover Retaining Nuts Pump Assembly Retaining Nuts End Plate or Valve Block Retaining Cap Screws Motor to Pump Retaining Cap Screws Drain and Filter Plugs
HYDRAULIC SPECIFICATIONS
PUMP Pressure Output (pump relief valve setting) CROSSOVER RELIEF VALVE Opening Pressure
2000 P.S.I.
38
I purchased this Diamond Equipment From an automobile Dealer From a truck equipment distributor This is the first Diamond product I have owned. I have owned Diamond products in the past I have owned competitive brands in the past What brands? Meyer Western Fisher Other Principal use of this Diamond equipment Personal use only Contract snow removal Retail business property Industrial property
I heard about Diamond through Newspaper AD T.V. Ad Radio Ad Yellow Pages Ad Automotive Dealer Truck Equipment Distributor Friend Which of the following most influenced your purchase of Diamond Equipment? Engineering & design features Price Previous experience or reputation
SNOWPLOWS by Meyer
Form No. 109R3 802 5M Printed in the U.S.A. 2002