Features

High-performance, Low-power AVR 8-bit Microcontroller Advanced RISC Architecture

130 Powerful Instructions Most Single Clock Cycle Execution 32 x 8 General Purpose Working Registers Fully Static Operation Up to 16 MIPS Throughput at 16 MHz On-chip 2-cycle Multiplier Nonvolatile Program and Data Memories 8K Bytes of In-System Self-Programmable Flash Endurance: 10,000 Write/Erase Cycles Optional Boot Code Section with Independent Lock Bits In-System Programming by On-chip Boot Program True Read-While-Write Operation 512 Bytes EEPROM Endurance: 100,000 Write/Erase Cycles 512 Bytes Internal SRAM Programming Lock for Software Security Peripheral Features Two 8-bit Timer/Counters with Separate Prescalers and Compare Modes One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode Real Time Counter with Separate Oscillator Four PWM Channels 8-channel, 10-bit ADC 8 Single-ended Channels 7 Differential Channels for TQFP Package Only 2 Differential Channels with Programmable Gain at 1x, 10x, or 200x for TQFP Package Only Byte-oriented Two-wire Serial Interface Programmable Serial USART Master/Slave SPI Serial Interface Programmable Watchdog Timer with Separate On-chip Oscillator On-chip Analog Comparator Special Microcontroller Features Power-on Reset and Programmable Brown-out Detection Internal Calibrated RC Oscillator External and Internal Interrupt Sources Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby and Extended Standby I/O and Packages 32 Programmable I/O Lines 40-pin PDIP, 44-lead TQFP, 44-lead PLCC, and 44-pad MLF Operating Voltages 2.7 - 5.5V for ATmega8535L 4.5 - 5.5V for ATmega8535 Speed Grades 0 - 8 MHz for ATmega8535L 0 - 16 MHz for ATmega8535

8-bit Microcontroller with 8K Bytes In-System Programmable Flash ATmega8535 ATmega8535L Preliminary Summary

Rev. 2502ESAVR12/03

Note: This is a summary document. A complete document is available on our Web site at www.atmel.com.

Pin Configurations

Figure 1. Pinout ATmega8535

(XCK/T0) PB0 (T1) PB1 (INT2/AIN0) PB2 (OC0/AIN1) PB3 (SS) PB4 (MOSI) PB5 (MISO) PB6 (SCK) PB7 RESET VCC GND XTAL2 XTAL1 (RXD) PD0 (TXD) PD1 (INT0) PD2 (INT1) PD3 (OC1B) PD4 (OC1A) PD5 (ICP1) PD6 PA0 (ADC0) PA1 (ADC1) PA2 (ADC2) PA3 (ADC3) PA4 (ADC4) PA5 (ADC5) PA6 (ADC6) PA7 (ADC7) AREF GND AVCC PC7 (TOSC2) PC6 (TOSC1) PC5 PC4 PC3 PC2 PC1 (SDA) PC0 (SCL) PD7 (OC2)

PLCC
PB4 (SS) PB3 (AIN1/OC0) PB2 (AIN0/INT2) PB1 (T1) PB0 (XCK/T0) GND VCC PA0 (ADC0) PA1 (ADC1) PA2 (ADC2) PA3 (ADC3) PB4 (SS) PB3 (AIN1/OC0) PB2 (AIN0/INT2) PB1 (T1) PB0 (XCK/T0) GND VCC PA0 (ADC0) PA1 (ADC1) PA2 (ADC2) PA3 (ADC3)
33 32 31 30 29 28 27 26 25 24 23 PA4 (ADC4) PA5 (ADC5) PA6 (ADC6) PA7 (ADC7) AREF GND AVCC PC7 (TOSC2) PC6 (TOSC1) PC5 PC4

44 43 42 41 40 39 38 37 36 35 34

(MOSI) PB5 (MISO) PB6 (SCK) PB7 RESET VCC GND XTAL2 XTAL1 (RXD) PD0 (TXD) PD1 (INT0) PD2

1 2 3 4 5 6 7 8 9 10 11

12 13 14 15 16 17 18 19 20 21 22

PD3 PD4 PD5 PD6 PD7 VCC GND (SCL) PC0 (SDA) PC1 PC2 PC3

(INT1) (OC1B) (OC1A) (ICP1) (OC2)

NOTE: MLF Bottom pad should be soldered to ground.

Disclaimer

Typical values contained in this data sheet are based on simulations and characterization of other AVR microcontrollers manufactured on the same process technology. Min and Max values will be available after the device is characterized.

ATmega8535(L)
2502ESAVR12/03

(INT1) (OC1B) (OC1A) (ICP1) (OC2)

PD3 PD4 PD5 PD6 PD7 VCC GND (SCL) PC0 (SDA) PC1 PC2 PC3

18 19 20 21 22 23 24 25 26 27 28

(MOSI) PB5 (MISO) PB6 (SCK) PB7 RESET VCC GND XTAL2 XTAL1 (RXD) PD0 (TXD) PD1 (INT0) PD2

6 5 4 3 2 1 44 43 42 41 40

7 8 9 10 11 12 13 14 15 16 17

39 38 37 36 35 34 33 32 31 30 29

PA4 (ADC4) PA5 (ADC5) PA6 (ADC6) PA7 (ADC7) AREF GND AVCC PC7 (TOSC2) PC6 (TOSC1) PC5 PC4

ATmega8535(L)
Overview
The ATmega8535 is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By executing instructions in a single clock cycle, the ATmega8535 achieves throughputs approaching 1 MIPS per MHz allowing the system designer to optimize power consumption versus processing speed. Figure 2. Block Diagram
PA0 - PA7 VCC PC0 - PC7

Block Diagram

PORTA DRIVERS/BUFFERS

PORTC DRIVERS/BUFFERS

GND

PORTA DIGITAL INTERFACE

PORTC DIGITAL INTERFACE

AVCC

MUX & ADC

AREF PROGRAM COUNTER

ADC INTERFACE

TWI

STACK POINTER

TIMERS/ COUNTERS

OSCILLATOR

PROGRAM FLASH

SRAM

INTERNAL OSCILLATOR XTAL1

INSTRUCTION REGISTER

GENERAL PURPOSE REGISTERS X

WATCHDOG TIMER

OSCILLATOR

XTAL2 MCU CTRL. & TIMING RESET

INSTRUCTION DECODER

Y Z

CONTROL LINES

ALU

INTERRUPT UNIT

INTERNAL CALIBRATED OSCILLATOR

AVR CPU

STATUS REGISTER

EEPROM

PROGRAMMING LOGIC

SPI

USART

+ -

COMP. INTERFACE

PORTB DIGITAL INTERFACE

PORTD DIGITAL INTERFACE

PORTB DRIVERS/BUFFERS

PORTD DRIVERS/BUFFERS

PB0 - PB7

PD0 - PD7

3
2502ESAVR12/03

The AVR core combines a rich instruction set with 32 general purpose working registers. All 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent registers to be accessed in one single instruction executed in one clock cycle. The resulting architecture is more code efficient while achieving throughputs up to ten times faster than conventional CISC microcontrollers. The ATmega8535 provides the following features: 8K bytes of In-System Programmable Flash with Read-While-Write capabilities, 512 bytes EEPROM, 512 bytes SRAM, 32 general purpose I/O lines, 32 general purpose working registers, three flexible Timer/Counters with compare modes, internal and external interrupts, a serial programmable USART, a byte oriented Two-wire Serial Interface, an 8-channel, 10-bit ADC with optional differential input stage with programmable gain in TQFP package, a programmable Watchdog Timer with Internal Oscillator, an SPI serial port, and six software selectable power saving modes. The Idle mode stops the CPU while allowing the SRAM, Timer/Counters, SPI port, and interrupt system to continue functioning. The Power-down mode saves the register contents but freezes the Oscillator, disabling all other chip functions until the next interrupt or Hardware Reset. In Power-save mode, the asynchronous timer continues to run, allowing the user to maintain a timer base while the rest of the device is sleeping. The ADC Noise Reduction mode stops the CPU and all I/O modules except asynchronous timer and ADC, to minimize switching noise during ADC conversions. In Standby mode, the crystal/resonator Oscillator is running while the rest of the device is sleeping. This allows very fast start-up combined with low-power consumption. In Extended Standby mode, both the main Oscillator and the asynchronous timer continue to run. The device is manufactured using Atmels high density nonvolatile memory technology. The On-chip ISP Flash allows the program memory to be reprogrammed In-System through an SPI serial interface, by a conventional nonvolatile memory programmer, or by an On-chip Boot program running on the AVR core. The boot program can use any interface to download the application program in the Application Flash memory. Software in the Boot Flash section will continue to run while the Application Flash section is updated, providing true Read-While-Write operation. By combining an 8-bit RISC CPU with In-System Self-Programmable Flash on a monolithic chip, the Atmel ATmega8535 is a powerful microcontroller that provides a highly flexible and cost effective solution to many embedded control applications. The ATmega8535 AVR is supported with a full suite of program and system development tools including: C compilers, macro assemblers, program debugger/simulators, InCircuit Emulators, and evaluation kits.

AT90S8535 Compatibility The ATmega8535 provides all the features of the AT90S8535. In addition, several new
features are added. The ATmega8535 is backward compatible with AT90S8535 in most cases. However, some incompatibilities between the two microcontrollers exist. To solve this problem, an AT90S8535 compatibility mode can be selected by programming the S8535C fuse. ATmega8535 is pin compatible with AT90S8535, and can replace the AT90S8535 on current Printed Circuit Boards. However, the location of fuse bits and the electrical characteristics differs between the two devices. AT90S8535 Compatibility Mode Programming the S8535C fuse will change the following functionality: The timed sequence for changing the Watchdog Time-out period is disabled. See Timed Sequences for Changing the Configuration of the Watchdog Timer on page 43 for details. The double buffering of the USART Receive Register is disabled. See AVR USART vs. AVR UART Compatibility on page 143 for details.

ATmega8535(L)
2502ESAVR12/03

ATmega8535(L)
Pin Descriptions
VCC GND Port A (PA7..PA0) Digital supply voltage. Ground. Port A serves as the analog inputs to the A/D Converter. Port A also serves as an 8-bit bi-directional I/O port, if the A/D Converter is not used. Port pins can provide internal pull-up resistors (selected for each bit). The Port A output buffers have symmetrical drive characteristics with both high sink and source capability. When pins PA0 to PA7 are used as inputs and are externally pulled low, they will source current if the internal pull-up resistors are activated. The Port A pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port B (PB7..PB0) Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port B output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port B pins that are externally pulled low will source current if the pull-up resistors are activated. The Port B pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port B also serves the functions of various special features of the ATmega8535 as listed on page 58. Port C (PC7..PC0) Port C is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port C output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port C pins that are externally pulled low will source current if the pull-up resistors are activated. The Port C pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port D is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port D output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port D pins that are externally pulled low will source current if the pull-up resistors are activated. The Port D pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port D also serves the functions of various special features of the ATmega8535 as listed on page 62. RESET Reset input. A low level on this pin for longer than the minimum pulse length will generate a reset, even if the clock is not running. The minimum pulse length is given in Table 15 on page 35. Shorter pulses are not guaranteed to generate a reset. Input to the inverting Oscillator amplifier and input to the internal clock operating circuit. Output from the inverting Oscillator amplifier. AVCC is the supply voltage pin for Port A and the A/D Converter. It should be externally connected to VCC, even if the ADC is not used. If the ADC is used, it should be connected to VCC through a low-pass filter. AREF is the analog reference pin for the A/D Converter.

Port D (PD7..PD0)

XTAL1 XTAL2 AVCC

AREF

5
2502ESAVR12/03

Register Summary
Address
0x3F (0x5F) 0x3E (0x5E) 0x3D (0x5D) 0x3C (0x5C) 0x3B (0x5B) 0x3A (0x5A) 0x39 (0x59) 0x38 (0x58) 0x37 (0x57) 0x36 (0x56) 0x35 (0x55) 0x34 (0x54) 0x33 (0x53) 0x32 (0x52) 0x31 (0x51) 0x30 (0x50) 0x2F (0x4F) 0x2E (0x4E) 0x2D (0x4D) 0x2C (0x4C) 0x2B (0x4B) 0x2A (0x4A) 0x29 (0x49) 0x28 (0x48) 0x27 (0x47) 0x26 (0x46) 0x25 (0x45) 0x24 (0x44) 0x23 (0x43) 0x22 (0x42) 0x21 (0x41) 0x20(1) (0x40)(1) 0x1F (0x3F) 0x1E (0x3E) 0x1D (0x3D) 0x1C (0x3C) 0x1B (0x3B) 0x1A (0x3A) 0x19 (0x39) 0x18 (0x38) 0x17 (0x37) 0x16 (0x36) 0x15 (0x35) 0x14 (0x34) 0x13 (0x33) 0x12 (0x32) 0x11 (0x31) 0x10 (0x30) 0x0F (0x2F) 0x0E (0x2E) 0x0D (0x2D) 0x0C (0x2C) 0x0B (0x2B) 0x0A (0x2A) 0x09 (0x29) 0x08 (0x28) 0x07 (0x27) 0x06 (0x26) 0x05 (0x25) 0x04 (0x24) 0x03 (0x23) 0x02 (0x22) 0x01 (0x21)

Name
SREG SPH SPL OCR0 GICR GIFR TIMSK TIFR SPMCR TWCR MCUCR MCUCSR TCCR0 TCNT0 OSCCAL SFIOR TCCR1A TCCR1B TCNT1H TCNT1L OCR1AH OCR1AL OCR1BH OCR1BL ICR1H ICR1L TCCR2 TCNT2 OCR2 ASSR WDTCR UBRRH UCSRC EEARH EEARL EEDR EECR PORTA DDRA PINA PORTB DDRB PINB PORTC DDRC PINC PORTD DDRD PIND SPDR SPSR SPCR UDR UCSRA UCSRB UBRRL ACSR ADMUX ADCSRA ADCH ADCL TWDR TWAR TWSR

Bit 7
I SP7 INT1 INTF1 OCIE2 OCF2 SPMIE TWINT SM2 FOC0

Bit 6
T SP6 INT0 INTF0 TOIE2 TOV2 RWWSB TWEA SE ISC2 WGM00

Bit 5
H SP5 INT2 INTF2 TICIE1 ICF1 TWSTA SM1 COM01

Bit 4
S SP4 OCIE1A OCF1A RWWSRE TWSTO SM0 COM00

Bit 3
V SP3 OCIE1B OCF1B BLBSET TWWC ISC11 WDRF WGM01

Bit 2
N SP10 SP2 TOIE1 TOV1 PGWRT TWEN ISC10 BORF CS02

Bit 1
Z SP9 SP1 IVSEL OCIE0 OCF0 PGERS ISC01 EXTRF CS01

Bit 0
C SP8 SP0 IVCE TOIE0 TOV0 SPMEN TWIE ISC00 PORF CS00

Page
8 10 10 83 47, 67 68 83, 113, 131 84, 114, 132 225 178 30, 66 38, 67 81 83 28

Timer/Counter0 Output Compare Register

Timer/Counter0 (8 Bits) Oscillator Calibration Register ADTS2 COM1A1 ICNC1 ADTS1 COM1A0 ICES1 ADTS0 COM1B1 COM1B0 WGM13 ACME FOC1A WGM12 PUD FOC1B CS12 PSR2 WGM11 CS11 PSR10 WGM10 CS10

57,86,133,200,220 108 111 112 112 112 112 112 112 112 112

Timer/Counter1 Counter Register High Byte Timer/Counter1 Counter Register Low Byte Timer/Counter1 Output Compare Register A High Byte Timer/Counter1 Output Compare Register A Low Byte Timer/Counter1 Output Compare Register B High Byte Timer/Counter1 Output Compare Register B Low Byte Timer/Counter1 Input Capture Register High Byte Timer/Counter1 Input Capture Register Low Byte FOC2 WGM20 COM21 COM20 WGM21 CS22 CS21 CS20 Timer/Counter2 (8 Bits) Timer/Counter2 Output Compare Register URSEL URSEL UMSEL UPM1 WDCE UPM0 USBS AS2 WDE TCN2UB WDP2 UCSZ1 OCR2UB WDP1 UBRR[11:8] UCSZ0 UCPOL EEAR8 TCR2UB WDP0

126 128 129 129 40 166 164 17 17 17

EEPROM Address Register Low Byte EEPROM Data Register PORTA7 DDA7 PINA7 PORTB7 DDB7 PINB7 PORTC7 DDC7 PINC7 PORTD7 DDD7 PIND7 SPIF SPIE RXC RXCIE ACD REFS1 ADEN PORTA6 DDA6 PINA6 PORTB6 DDB6 PINB6 PORTC6 DDC6 PINC6 PORTD6 DDD6 PIND6 WCOL SPE TXC TXCIE ACBG REFS0 ADSC PORTA5 DDA5 PINA5 PORTB5 DDB5 PINB5 PORTC5 DDC5 PINC5 PORTD5 DDD5 PIND5 DORD UDRE UDRIE ACO ADLAR ADATE PORTA4 DDA4 PINA4 PORTB4 DDB4 PINB4 PORTC4 DDC4 PINC4 PORTD4 DDD4 PIND4 MSTR FE RXEN ACI MUX4 ADIF EERIE PORTA3 DDA3 PINA3 PORTB3 DDB3 PINB3 PORTC3 DDC3 PINC3 PORTD3 DDD3 PIND3 CPOL DOR TXEN ACIE MUX3 ADIE EEMWE PORTA2 DDA2 PINA2 PORTB2 DDB2 PINB2 PORTC2 DDC2 PINC2 PORTD2 DDD2 PIND2 CPHA PE UCSZ2 ACIC MUX2 ADPS2 EEWE PORTA1 DDA1 PINA1 PORTB1 DDB1 PINB1 PORTC1 DDC1 PINC1 PORTD1 DDD1 PIND1 SPR1 U2X RXB8 ACIS1 MUX1 ADPS1 EERE PORTA0 DDA0 PINA0 PORTB0 DDB0 PINB0 PORTC0 DDC0 PINC0 PORTD0 DDD0 PIND0 SPI2X SPR0 MPCM TXB8 ACIS0 MUX0 ADPS0

17 64 64 64 64 64 65 65 65 65 65 65 65 140 140 138 161 162 163 166 200 216 218 219 219 180

SPI Data Register

USART I/O Data Register

USART Baud Rate Register Low Byte

ADC Data Register High Byte ADC Data Register Low Byte Two-wire Serial Interface Data Register TWA6 TWS7 TWA5 TWS6 TWA4 TWS5 TWA3 TWS4 TWA2 TWS3 TWA1 TWA0 TWPS1 TWGCE TWPS0

180 180

ATmega8535(L)
2502ESAVR12/03

ATmega8535(L)
Register Summary (Continued)
Address
0x00 (0x20)

Name
TWBR

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Page
178

Two-wire Serial Interface Bit Rate Register

Notes:

1. Refer to the USART description for details on how to access UBRRH and UCSRC. 2. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses should never be written. 3. Some of the status flags are cleared by writing a logical one to them. Note that the CBI and SBI instructions will operate on all bits in the I/O Register, writing a one back into any flag read as set, thus clearing the flag. The CBI and SBI instructions work with registers 0x00 to 0x1F only.

7
2502ESAVR12/03

Instruction Set Summary

Mnemonics
ADD ADC ADIW SUB SUBI SBC SBCI SBIW AND ANDI OR ORI EOR COM NEG SBR CBR INC DEC TST CLR SER MUL MULS MULSU FMUL FMULS FMULSU RJMP IJMP RCALL ICALL RET RETI CPSE CP CPC CPI SBRC SBRS SBIC SBIS BRBS BRBC BREQ BRNE BRCS BRCC BRSH BRLO BRMI BRPL BRGE BRLT BRHS BRHC BRTS BRTC BRVS BRVC BRIE BRID Rd,Rr Rd,Rr Rd,Rr Rd,K Rr, b Rr, b P, b P, b s, k s, k k k k k k k k k k k k k k k k k k k k

Operands
Rd, Rr Rd, Rr Rdl,K Rd, Rr Rd, K Rd, Rr Rd, K Rdl,K Rd, Rr Rd, K Rd, Rr Rd, K Rd, Rr Rd Rd Rd,K Rd,K Rd Rd Rd Rd Rd Rd, Rr Rd, Rr Rd, Rr Rd, Rr Rd, Rr Rd, Rr k

Description
Add two Registers Add with Carry two Registers Add Immediate to Word Subtract two Registers Subtract Constant from Register Subtract with Carry two Registers Subtract with Carry Constant from Reg. Subtract Immediate from Word Logical AND Registers Logical AND Register and Constant Logical OR Registers Logical OR Register and Constant Exclusive OR Registers Ones Complement Twos Complement Set Bit(s) in Register Clear Bit(s) in Register Increment Decrement Test for Zero or Minus Clear Register Set Register Multiply Unsigned Multiply Signed Multiply Signed with Unsigned Fractional Multiply Unsigned Fractional Multiply Signed Fractional Multiply Signed with Unsigned Relative Jump Indirect Jump to (Z) Relative Subroutine Call Indirect Call to (Z) Subroutine Return Interrupt Return Compare, Skip if Equal Compare Compare with Carry Compare Register with Immediate Skip if Bit in Register Cleared Skip if Bit in Register is Set Skip if Bit in I/O Register Cleared Skip if Bit in I/O Register is Set Branch if Status Flag Set Branch if Status Flag Cleared Branch if Equal Branch if Not Equal Branch if Carry Set Branch if Carry Cleared Branch if Same or Higher Branch if Lower Branch if Minus Branch if Plus Branch if Greater or Equal, Signed Branch if Less Than Zero, Signed Branch if Half Carry Flag Set Branch if Half Carry Flag Cleared Branch if T Flag Set Branch if T Flag Cleared Branch if Overflow Flag is Set Branch if Overflow Flag is Cleared Branch if Interrupt Enabled Branch if Interrupt Disabled

Operation
Rd Rd + Rr Rd Rd + Rr + C Rdh:Rdl Rdh:Rdl + K Rd Rd - Rr Rd Rd - K Rd Rd - Rr - C Rd Rd - K - C Rdh:Rdl Rdh:Rdl - K Rd Rd Rr Rd Rd K Rd Rd v Rr Rd Rd v K Rd Rd Rr Rd 0xFF Rd Rd 0x00 Rd Rd Rd v K Rd Rd (0xFF - K) Rd Rd + 1 Rd Rd 1 Rd Rd Rd Rd Rd Rd Rd 0xFF R1:R0 Rd x Rr R1:R0 Rd x Rr R1:R0 Rd x Rr

Flags
Z,C,N,V,H Z,C,N,V,H Z,C,N,V,S Z,C,N,V,H Z,C,N,V,H Z,C,N,V,H Z,C,N,V,H Z,C,N,V,S Z,N,V Z,N,V Z,N,V Z,N,V Z,N,V Z,C,N,V Z,C,N,V,H Z,N,V Z,N,V Z,N,V Z,N,V Z,N,V Z,N,V None Z,C Z,C Z,C Z,C Z,C Z,C None None None None None I None Z, N,V,C,H Z, N,V,C,H Z, N,V,C,H None None None None None None None None None None None None None None None None None None None None None None None None

#Clocks
1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 3 3 4 4 1/2/3 1 1 1 1/2/3 1/2/3 1/2/3 1/2/3 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2

ARITHMETIC AND LOGIC INSTRUCTIONS

1 R1:R0 (Rd x Rr) << 1 R1:R0 (Rd x Rr) << 1

PC PC + k + 1 PC Z PC PC + k + 1 PC Z PC STACK PC STACK if (Rd = Rr) PC PC + 2 or 3 Rd Rr Rd Rr C Rd K if (Rr(b)=0) PC PC + 2 or 3 if (Rr(b)=1) PC PC + 2 or 3 if (P(b)=0) PC PC + 2 or 3 if (P(b)=1) PC PC + 2 or 3 if (SREG(s) = 1) then PC PC+k + 1 if (SREG(s) = 0) then PC PC+k + 1 if (Z = 1) then PC PC + k + 1 if (Z = 0) then PC PC + k + 1 if (C = 1) then PC PC + k + 1 if (C = 0) then PC PC + k + 1 if (C = 0) then PC PC + k + 1 if (C = 1) then PC PC + k + 1 if (N = 1) then PC PC + k + 1 if (N = 0) then PC PC + k + 1 if (N V= 0) then PC PC + k + 1 if (N V= 1) then PC PC + k + 1 if (H = 1) then PC PC + k + 1 if (H = 0) then PC PC + k + 1 if (T = 1) then PC PC + k + 1 if (T = 0) then PC PC + k + 1 if (V = 1) then PC PC + k + 1 if (V = 0) then PC PC + k + 1 if ( I = 1) then PC PC + k + 1 if ( I = 0) then PC PC + k + 1

R1:R0 (Rd x Rr) <<

BRANCH INSTRUCTIONS

DATA TRANSFER INSTRUCTIONS

ATmega8535(L)
2502ESAVR12/03

ATmega8535(L)
Mnemonics
MOV MOVW LDI LD LD LD LD LD LD LDD LD LD LD LDD LDS ST ST ST ST ST ST STD ST ST ST STD STS LPM LPM LPM SPM IN OUT PUSH POP SBI CBI LSL LSR ROL ROR ASR SWAP BSET BCLR BST BLD SEC CLC SEN CLN SEZ CLZ SEI CLI SES CLS SEV CLV SET CLT SEH CLH MCU CONTROL INSTRUCTIONS NOP No Operation None 1 Rd, P P, Rr Rr Rd P,b P,b Rd Rd Rd Rd Rd Rd s s Rr, b Rd, b Rd, Z Rd, Z+

Operands
Rd, Rr Rd, Rr Rd, K Rd, X Rd, X+ Rd, - X Rd, Y Rd, Y+ Rd, - Y Rd,Y+q Rd, Z Rd, Z+ Rd, -Z Rd, Z+q Rd, k X, Rr X+, Rr - X, Rr Y, Rr Y+, Rr - Y, Rr Y+q,Rr Z, Rr Z+, Rr -Z, Rr Z+q,Rr k, Rr

Description
Move Between Registers Copy Register Word Load Immediate Load Indirect Load Indirect and Post-Inc. Load Indirect and Pre-Dec. Load Indirect Load Indirect and Post-Inc. Load Indirect and Pre-Dec. Load Indirect with Displacement Load Indirect Load Indirect and Post-Inc. Load Indirect and Pre-Dec. Load Indirect with Displacement Load Direct from SRAM Store Indirect Store Indirect and Post-Inc. Store Indirect and Pre-Dec. Store Indirect Store Indirect and Post-Inc. Store Indirect and Pre-Dec. Store Indirect with Displacement Store Indirect Store Indirect and Post-Inc. Store Indirect and Pre-Dec. Store Indirect with Displacement Store Direct to SRAM Load Program Memory Load Program Memory Load Program Memory and Post-Inc Store Program Memory In Port Out Port Push Register on Stack Pop Register from Stack Set Bit in I/O Register Clear Bit in I/O Register Logical Shift Left Logical Shift Right Rotate Left Through Carry Rotate Right Through Carry Arithmetic Shift Right Swap Nibbles Flag Set Flag Clear Bit Store from Register to T Bit load from T to Register Set Carry Clear Carry Set Negative Flag Clear Negative Flag Set Zero Flag Clear Zero Flag Global Interrupt Enable Global Interrupt Disable Set Signed Test Flag Clear Signed Test Flag Set Twos Complement Overflow. Clear Twos Complement Overflow Set T in SREG Clear T in SREG Set Half Carry Flag in SREG Clear Half Carry Flag in SREG

Operation
Rd Rr Rd+1:Rd Rr+1:Rr Rd K Rd (X) Rd (X), X X + 1 X X - 1, Rd (X) Rd (Y) Rd (Y), Y Y + 1 Y Y - 1, Rd (Y) Rd (Y + q) Rd (Z) Rd (Z), Z Z+1 Z Z - 1, Rd (Z) Rd (Z + q) Rd (k) (X) Rr (X) Rr, X X + 1 X X - 1, (X) Rr (Y) Rr (Y) Rr, Y Y + 1 Y Y - 1, (Y) Rr (Y + q) Rr (Z) Rr (Z) Rr, Z Z + 1 Z Z - 1, (Z) Rr (Z + q) Rr (k) Rr R0 (Z) Rd (Z) Rd (Z), Z Z+1 (Z) R1:R0 Rd P P Rr STACK Rr Rd STACK I/O(P,b) 1 I/O(P,b) 0 Rd(n+1) Rd(n), Rd(0) 0 Rd(n) Rd(n+1), Rd(7) 0 Rd(0)C,Rd(n+1) Rd(n),CRd(7) Rd(7)C,Rd(n) Rd(n+1),CRd(0) Rd(n) Rd(n+1), n=0..6 Rd(3..0)Rd(7..4),Rd(7..4)Rd(3..0) SREG(s) 1 SREG(s) 0 T Rr(b) Rd(b) T C1 C0 N1 N0 Z1 Z0 I1 I 0 S1 S0 V1 V0 T1 T0 H1 H0

Flags
None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None Z,C,N,V Z,C,N,V Z,C,N,V Z,C,N,V Z,C,N,V None SREG(s) SREG(s) T None C C N N Z Z I I S S V V T T H H

#Clocks
1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 1 1 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

BIT AND BIT-TEST INSTRUCTIONS

9
2502ESAVR12/03

Mnemonics
SLEEP WDR BREAK

Operands

Description
Sleep Watchdog Reset Break

Operation
(see specific descr. for Sleep function) (see specific descr. for WDR/Timer) For On-chip Debug Only

Flags
None None None

#Clocks
1 1 N/A

10

ATmega8535(L)
2502ESAVR12/03

ATmega8535(L)
Ordering Information
Speed (MHz) Power Supply Ordering Code ATmega8535L-8AC ATmega8535L-8PC ATmega8535L-8JC ATmega8535L-8MC ATmega8535L-8AI ATmega8535L-8PI ATmega8535L-8JI ATmega8535L-8MI ATmega8535-16AC ATmega8535-16PC ATmega8535-16JC ATmega8535-16MC ATmega8535-16AI ATmega8535-16PI ATmega8535-16JI ATmega8535-16MI Package(1) 44A 40P6 44J 44M1 44A 40P6 44J 44M1 44A 40P6 44J 44M1 44A 40P6 44J 44M1 Operation Range Commercial (0C to 70C)

2.7 - 5.5V

Industrial (-40C to 85C)

Commercial (0C to 70C)

16

4.5 - 5.5V

Industrial (-40C to 85C)

Note:

1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities.

Package Type 44A 40P6 44J 44M1-A 44-lead, Thin (1.0 mm) Plastic Gull Wing Quad Flat Package (TQFP) 40-pin, 0.600 Wide, Plastic Dual Inline Package (PDIP) 44-lead, Plastic J-leaded Chip Carrier (PLCC) 44-pad, 7 x 7 x 1.0 mm body, lead pitch 0.50 mm, Micro Lead Frame Package (MLF)

11
2502ESAVR12/03

Packaging Information
44A

PIN 1 B
PIN 1 IDENTIFIER

E1

D1 D C

0~7 A1 L
COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL A A1 A2 D D1 E MIN 0.05 0.95 11.75 9.90 11.75 9.90 0.30 0.09 0.45 NOM 1.00 12.00 10.00 12.00 10.00 0.80 TYP MAX 1.20 0.15 1.05 12.25 10.10 12.25 10.10 0.45 0.20 0.75 Note 2 Note 2 NOTE

A2

Notes:

1. This package conforms to JEDEC reference MS-026, Variation ACB. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum plastic body size dimensions including mold mismatch. 3. Lead coplanarity is 0.10 mm maximum.

E1 B C L e

10/5/2001 2325 Orchard Parkway San Jose, CA 95131 TITLE 44A, 44-lead, 10 x 10 mm Body Size, 1.0 mm Body Thickness, 0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) DRAWING NO. 44A REV. B

12

ATmega8535(L)
2502ESAVR12/03

ATmega8535(L)
40P6

PIN 1

E1

SEATING PLANE

L B1 e E B

A1

C eB

0 ~ 15

REF
SYMBOL A A1 D E E1 B

COMMON DIMENSIONS (Unit of Measure = mm) MIN 0.381 52.070 15.240 13.462 0.356 1.041 3.048 0.203 15.494 NOM 2.540 TYP MAX 4.826 52.578 15.875 13.970 0.559 1.651 3.556 0.381 17.526 Note 2 Note 2 NOTE

Notes:

1. This package conforms to JEDEC reference MS-011, Variation AC. 2. Dimensions D and E1 do not include mold Flash or Protrusion. Mold Flash or Protrusion shall not exceed 0.25 mm (0.010").

B1 L C eB e

09/28/01 2325 Orchard Parkway San Jose, CA 95131 TITLE 40P6, 40-lead (0.600"/15.24 mm Wide) Plastic Dual Inline Package (PDIP) DRAWING NO. 40P6 REV. B

13
2502ESAVR12/03

44J

1.14(0.045) X 45

PIN NO. 1 IDENTIFIER

1.14(0.045) X 45 0.318(0.0125) 0.191(0.0075)

E1 B

B1

D2/E2

e D1 D A A2 A1

0.51(0.020)MAX 45 MAX (3X)

COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL A A1 A2 D D1 E Notes: 1. This package conforms to JEDEC reference MS-018, Variation AC. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010"(0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102 mm) maximum. E1 D2/E2 B B1 e MIN 4.191 2.286 0.508 17.399 16.510 17.399 16.510 14.986 0.660 0.330 NOM 1.270 TYP MAX 4.572 3.048 17.653 16.662 17.653 16.662 16.002 0.813 0.533 Note 2 Note 2 NOTE

10/04/01 2325 Orchard Parkway San Jose, CA 95131 TITLE 44J, 44-lead, Plastic J-leaded Chip Carrier (PLCC) DRAWING NO. 44J REV. B

14

ATmega8535(L)
2502ESAVR12/03

ATmega8535(L)
44M1-A

Marked Pin# 1 ID

SEATING PLANE

TOP VIEW

A1 A3 A

L D2

Pin #1 Corner

SIDE VIEW

COMMON DIMENSIONS (Unit of Measure = mm)

E2

SYMBOL A A1 A3 b D

MIN 0.80

NOM 0.90 0.02 0.25 REF

MAX 1.00 0.05

NOTE

0.18

0.23 7.00 BSC

0.30

b
BOTTOM VIEW

D2 E E2 e

5.00

5.20 7.00 BSC

5.40

5.00

5.20 0.50 BSC

5.40

Notes: 1. JEDEC Standard MO-220, Fig. 1 (SAW Singulation) VKKD-1.

0.35

0.55

0.75

01/15/03 2325 Orchard Parkway San Jose, CA 95131 TITLE 44M1, 44-pad, 7 x 7 x 1.0 mm Body, Lead Pitch 0.50 mm Micro Lead Frame Package (MLF) DRAWING NO. 44M1 REV. C

15
2502ESAVR12/03

Errata

There are no errata for this revision of ATmega8535.

16

ATmega8535(L)
2502ESAVR12/03

ATmega8535(L)
Datasheet Change Log for ATmega8535
Changes from Rev. 2502D-09/03 to Rev. 2502E-12/03 Changes from Rev. 2502C-04/03 to Rev. 2502D-09/03
Please note that the referring page numbers in this section are referring to this document. The referring revision in this section are referring to the document revision. 1. Updated Calibrated Internal RC Oscillator on page 27. 2. Added section Errata on page 16. 1. Removed Advance Information and some TBDs from the datasheet. 2. Added note to Pinout ATmega8535 on page 2. 3. Updated Reset Characteristics on page 35. 4. Updated Absolute Maximum Ratings and DC Characteristics in Electrical Characteristics on page 252. 5. Updated Table 111 on page 255. 6. Updated ADC Characteristics Preliminary Data on page 260. 7. Updated ATmega8535 Typical Characteristics Preliminary Data on page 263. 8. Removed CALL and JMP instructions from code examples and Instruction Set Summary on page 8.

Changes from Rev. 2502B-09/02 to Rev. 2502C-04/03

1. Updated Packaging Information on page 12. 2. Updated Figure 1 on page 2, Figure 84 on page 176, Figure 85 on page 182, Figure 87 on page 188, Figure 98 on page 204. 3. Added the section EEPROM Write During Power-down Sleep Mode on page 20. 4. Removed the references to the application notes Multi-purpose Oscillator and 32 kHz Crystal Oscillator, which do not exist. 5. Updated code examples on page 42. 6. Removed ADHSM bit. 7. Renamed Port D pin ICP to ICP1. See Alternate Functions of Port D on page 62. 8. Added information about PWM symmetry for Timer 0 on page 77 and Timer 2 on page 124. 9. Updated Table 68 on page 166, Table 75 on page 187, Table 76 on page 190, Table 77 on page 193, Table 108 on page 250, Table 113 on page 258. 10. Updated description on Bit 5 TWSTA: TWI START Condition Bit on page 179. 17

2502ESAVR12/03

11. Updated the description in Filling the Temporary Buffer (Page Loading) and Performing a Page Write on page 228. 12. Removed the section description in SPI Serial Programming Characteristics on page 251. 13. Updated Electrical Characteristics on page 252. 14. Updated ADC Characteristics Preliminary Data on page 260. 14. Updated Register Summary on page 6. 15. Various Timer 1 corrections. 16. Added WD_FUSE period in Table 108 on page 250.

Changes from Rev. 2502A-06/02 to Rev. 2502B-09/02

1. Canged the Endurance on the Flash to 10,000 Write/Erase Cycles.

18

ATmega8535(L)
2502ESAVR12/03

Atmel Corporation
2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600

Atmel Operations
Memory
2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314

RF/Automotive
Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759

Regional Headquarters
Europe
Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500

Microcontrollers
2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60

Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom

Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80

Asia
Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369

ASIC/ASSP/Smart Cards
Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743

Japan
9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581

Literature Requests
www.atmel.com/literature

Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Companys standard warranty which is detailed in Atmels Terms and Conditions located on the Companys web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmels products are not authorized for use as critical components in life support devices or systems.

Atmel Corporation 2003 . All rights reserved. Atmel and combinations thereof, AVR, and AVR Studio are the registered trademarks of Atmel Corporation or its subsidiaries. Microsoft , Windows, Windows NT, and Windows XP are the registered trademarks of Microsoft Corporation. Other terms and product names may be the trademarks of others

Printed on recycled paper.

2502ESAVR12/03

This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.