NOISE Notes
NOISE Notes
With reference to an electrical system, noise may be defined as any unwanted form of energy which tends to interfere with proper reception and reproduction of wanted signal. OR Noise is random, undesirable electrical energy that enters the communications system via the communicating medium and interferes with the transmitted message. However, some noise is also produced in the receiver.
Classification of Noise
Noise may be put into following two categories. 1. External noises, i.e. noise whose sources are external. External noise may be classified into the following three types: 1. Atmospheric noises 2. Extraterrestrial noises 3. Man-made noises or industrial noises. 2. Internal noise in communication, i.e. noises which get, generated within the receiver or communication system. Internal noise may be put into the following four categories. 1. 2. 3. 4. Thermal noise or white noise or Johnson noise Shot noise. Transit time noise Miscellaneous internal noise.
External noise cannot be reduced except by changing the location of the receiver or the entire system. Internal noise on the other hand can be easily evaluated Mathematically and can be reduced to a great extent by proper design. As already said, because of the fact that internal noise can be reduced to a great extent, study of noise characteristics is a very important part of the communication engineering.
same frequency. Accordingly at a given receiving point, the receiving antenna picks up not only the signal but also the static from all the thunderstorms, local or remote. The field strength of atmospheric noise varies approximately inversely with the frequency. Thus large atmospheric noise is generated in low and medium frequency (broadcast) bands while very little noise is generated in the VHF and UHF bands. Further VHF and UHF components of noise are limited to the line-of-sight (less than about 80 Km) propagation. For these two-reasons, the atmospheric noise becomes less severe at Frequencies exceeding about 30 MHz.
Extraterrestrial Noise
There are numerous types of extraterrestrial noise or space noises depending on their sources. However, these may be put into following two subgroups. 1. Solar noise 2. Cosmic noise
Solar Noise
This is the electrical noise emanating from the sun. Under quite conditions, there is a steady radiation of noise from the sun. This results because sun is a large body at a very high temperature (exceeding 6000C on the surface), and radiates electrical energy in the form of noise over a very wide frequency spectrum including the spectrum used for radio communication. The intensity produced by the sun varies with time. In fact, the sun has a repeating 11-Year noise cycle. During the peak of the cycle, the sun produces some amount of noise that causes tremendous radio signal interference, making many frequencies unusable for communications. During other years. the noise is at a minimum level.
Cosmic noise
Distant stars are also suns and have high temperatures. These stars, therefore, radiate noise in the same way as our sun. The noise received from these distant stars is thermal noise (or black body noise) and is distributing almost uniformly over the entire sky. We also receive noise from the center of our own galaxy (The Milky Way) from other distant galaxies and from other virtual point sources such as quasars and pulsars.
Thermal Noise
Conductors contain a large number of 'free" electrons and "ions" strongly bound by molecular forces. The ions vibrate randomly about their normal (average) positions, however, this vibration being a function of the temperature. Continuous collisions between the electrons and the vibrating ions take place. Thus there is a continuous transfer of energy between the ions and electrons. This is the source of resistance in a conductor. The movement of free electrons constitutes a current which is purely random in nature and over a long time averages zero. There is a random motion of the electrons which give rise to noise voltage called thermal noise. Thus noise generated in any resistance due to random motion of electrons i5 called thermal noise or white or Johnson noise. The analysis of thermal noise is based on the Kinetic theory. It shows that the temperature of particles is a way of expressing its internal kinetic energy. Thus "Temperature" of a body can be said to be equivalent to the statistical rms value of the velocity of motion of the particles in the body. At -273C (or zero degree Kelvin) the kinetic energy of the particles of a body becomes zero .Thus we can relate the noise power generated by a resistor to be proportional to its absolute temperature. Noise power is also proportional to the bandwidth over which it is measured. From the above discussion we can write down. Pn TB Pn = KTB ------ (1) Where Pn = Maximum noise power output of a resistor. K = Boltzmanns constant = 1.38 x10-23 joules I Kelvin. T = Absolute temperature. B = Bandwidth over which noise is measured. From equation (1), an equivalent circuit can be drawn as shown in below figure
From equation (2), we see that the square of the rms noise voltage is proportional to the absolute temperature of le resistor, the value of the resistor, and the bandwidth over which it is measured. En is quite independent of the Frequency. Example R.F. amplifier is saving an input resistor of 8Kr and works in the frequency range of 12 to 15.5 MHz Calculate the rms noise voltage at the input to this amplifier at an ambient temperature of 17oC? Solution:
Shot Noise
The most common type of noise is referred to as shot noise which is produced by the random arrival of 'electrons or holes at the output element, at the plate in a tube, or at the collector or drain in a transistor. Shot noise is also produced by the random movement of electrons or holes across a PN junction. Even through current flow is established by external bias voltages, there will still be some random movement of
electrons or holes due to discontinuities in the device. An example of such a discontinuity is the contact between the copper lead and the semiconductor materials. The interface between the two creates a discontinuity that causes random movement of the current carriers.
Partition Noise
Partition noise occurs whenever current has to divide between two or more paths, and results from the random fluctuations in the division. It would be expected, therefore, that a diode would be less noisy than a transistor (all other factors being equal) If the third electrode draws current (i.e.., the base current). It is for this reason that the inputs of microwave receivers are often taken directly to diode mixers.
A receiver has an input signal power of l.2W. The noise power is 0.80W. The signal to noise ratio is Signal to Noise Ratio = 10 Log (1.2/0.8) = 10 log 1.5 = 10 (0.176) = 1.76 dB
Noise Figure
Noise Figure F is designed as the ratio of the signal-to-noise power at the input to the signal to noise power at the output. The device under consideration can be the entire receiver or a single amplifier stage. The noise figure F also called the noise factor can be computed with the expression F = Signal to Noise power Input/Signal to noise power output You can express the noise figure as a number, more often you will see it expressed in decibels.
http://www.daenotes.com/electronics/communication-system/noise#axzz2Mlewr87Z