IS : 8380

( Part III ) - 1977 ( Reaffirmed 1992 ) ( Reaffirmed 1997 )

Indian Standard
SPECIFICATION FOR FABRICATED HIGH DENSITY POLYETHYLENE (HDPE) FITTINGS FOR POTABLE WATER SUPPLIES
PART Ill SPECIFIC REQUIREMENTS FOR 90 BENDS

( Second Reprint JANUARY 1998 )

UDC

621.643.4.062.3

: [ 678.742.2

] : 696.115

0 Copyright

1977

BUREAU
MANAK

OF

INDIAN

STANDARDS
ZAFAR MARG

BHAVAN,

9 BAHADUR SHAH NEW DELHI 110002

Gr2

May 1977

IS : $360 ( Part III ) - 1977

Indian Standard
SPECIFICATION FOR FABRICATED HIGH DENSITY POLYETHYLENE ( HDPE ) FITTINGS FOR POTABLE WATER SUPPLIES
PART III
Sanitary

SPECIFIC

REQUIREMENTS

FOR 90 BENDS
Committee, BDC 3

Appliances

and Water Fittings Sectional

Chairman SHRYV. D. DESAI Members

Refwesenting Bombay Municipal Corporation

Ministry of Health ADVISER SHRI B. B. RAU ( Alternate ) Indian Iron & Steel Co Ltd, Calcutta SHR~ H. R. BADYAL SHRI K. D. BISWAS ( Alternate ) Central Building Research Institute ( CSIR ), SHRI S. P. CHAKRABARTI Roorkee SHRI S. K. SHARMA ( Alternate ) Central Public Works Department, New Delhi CHIEF ENGINEER SUPERINTENDING ENGINEER ( Alternate ) Tamil Nadu Water Supply & Drainage Board, CHIEF ENGINEER Madras U. P. Jal Nigam, Lucknow CHIEF ENGINEER SUPERINTENDINGI ENOIMEER ( Alternate ) Municipal Corporation of Delhi GRIEF ENGINEER ( WATER ) DRAINAQE ENQINEER ( Alternate ) Bombay Municipal Corporation CITY ENGINEER HYDRAULIC ENGINEER ( Alternate ) Indian Institute of Architects, Bombay SRRI H. N. DALLAS National Test House, Calcutta LALA G. C. DAS Institution of Engineers ( India ), Calcutta SHRI T. R. DE Directorate General of Supplies & Disposals SHRI M. T. KANSE Delhi Development Authority SHRI S. C. KAPOOR Central Glass 8~ Ceramic Research SHRI R. V. LELE Institrrtc ( CSIR ), Calcutta National Environmental Engineering Research PROF N. MAJUMDER Institute I CSIR 1. Namur SHRI J. M. DAVE ( Altcmnte ) Directorate General of Technical Development SERI R. N. MALLICK SHRI N. R. SRINIVASAN ( Alternate ) ( Continued on page 2 ) @ Copyright 1977

BUREAU OF INDIAN STANDARDS This publication is protected under the In&a -cOprighf Act ( XIV of 1957 ) a& reproduction in whols or in part by any means except with ~written permissinn of the publisher shall be deemed to be an infringement of copyright under the said Act.

IS I 8369 -( Part III ) - 1977

( Conrinucdfrom page 1 ) MCdWS SHRI R.M. MEHRA SHRI R. N. MUKE~RJEE SARI 9. K. NEOQI ( Alternate ) SRRI D. APPUKUTTAN NAYAR Bombay Calcutta Representing Potteries & Tiles Ltd, Bombay Metropolitan Planning Organization

Public Health Engineering Department, Government of Kerala, Trivandrum SHRI K. RAMACHANDRAN( Alternate ) COL RAJ KUMAR Engineer-in-Chiefs Branch, Army Headquarters SHRI I. S. BEDI ( Alternate ) Public Health Engineering Department, -Government SHRI P. S. RAJVANSHI of Rajasthan, Jaipur SHRI RANJIT SINCWI Ministry qf Railways National Buildings Organization, New Delhi DR A. V. R. RAO SHRI G. T. BRIDE ( Al&n&e ) SBRI P. JAQANATH RAO E. I. D. Parry Ltd, Madras SHRI T.S. CHINTAYANI (Alternate) Public Health Engineering Department, Government SARI J. L. SETHI of Haryana, Chandigarh SERI A. N. MEHAXDALE ( Alternate ) Ltd, & Industries Sanitaryware Sari R. K. SOMANY Hindustan Bahadurgarh SERI V. S. BHAIT ( A&mats ) Director General, BIS ( Ex-o&o Member ) SHBI D. AJITHA bSHA, Director ( Civ Engg ) Secretary Assistant SRRI S. P. hdAWV Director ( Civ Engg ), ISI

Plastic
C0fM?b?r

Pipes Subcommittee,
Bombay Municipal

BDC

3 :8

SH~I K. D. MULEKAR MClllbUS

Corporation

S-1 S. H. MEUTRE ( Aftcrnatr to Shri K. D. Mulekar ) Ministry of Health ADVIBEB S&I V. A. ANAIQDADOW ( Aft@na& ) Calico Chemicals, Plastics and Fibres Division, Da B. R. C. ANAND &JUibay SHB~ S. MITBA ( Altemafe ) Housing & Urban Development Corporation Ltd, SEEI P. M. ANTE New Delhi SJXEIB. K. CEAJSBABAIWY (-Alrmurtr ) Public Health Engineering Department, Government Smu S. BHWXHALIN~AM of Kcrala, Trivandrum Garware Plastics ( Pvt ) Ltd, Bombay SESI H. R. BUTANI SHBI B. K. CMWLA ( Al-8 ) ( Continued oa bags 6

IS t 8366 ( Part III ) - 1977

Indian Standard
SPECIFICATION FOR FABRICATED HIGH DENSITY POLYETHYLENE ( HDPE ) FITTINGS FOR POTABLE WATER SUPPLIES
PART 111 SPECIFIC REQUIREMENTS FOR 90 BENDS

0.

FOREWORD

0.1 This Indian Standard ( Part III ) was adopted by the Indian Standards Institution on 17 January 1977, after the draft finalized by the Sanitary Appliances and Water Fittings Sectional Committee had been approved by the Civil Engineering Division Council. 0.2 The fabricated HDPE fittings are used for connection, process, to HDPE pipes covered by IS : 4984-1972*. by welding

0.3 The requirements of fabricated -HDPE fittings are covered in three parts of this standard, Part I of the series deals with the general requirements applicable to all fabricated HDPE fittings, and specific requirements of different types of fittings are covered in separate parts This Part III deals with the specific requirements for of the standard. 90 bends. 0.4 For the purpose of deciding whether a particular requirement of this standard is complied with, the final values, observed or calculated, expressing the result of a test or analysis, shall be rounded off in accordance with IS : 2-196Ot. The number of significant places retained in the rounded off values should be the same as that of the specified values in this standard.

1. SCOPE 1.1 This standard ( Part III ) lays down the requirements for manufacture, dimensions and tolerances and marking for fabricated HDPE 90 bends for potable water supplies. *Specific&on for high density polyethylene pipes for potable (fist r0oiSi411) . tRutea for rounding off numerical valuea ( ruiwd ). 3
water supplies

IS : 8360 ( Part III ) - 1977 2. REQUIREMENTS 2.1 General

2.2

- The general requirements for material, sizes, methods of test and sampling shall conform to IS :8360 ( Part I )-1977*. Manufacture 2.2.1 A typical
illustration of 90 fabricated bend is shown in Fig. I.

FIG. 1 2.2.2 thereon

90 BEND

Luyiag Length shall comply

The overall laying length 5 and the tolerances with those given in Table 1 read with Fig. 1.

2.2.3 The outside diameters and wall thicknesses of pipes out of which 90 bends are fabricated shall comply with those given in IS : 8360 The wall thickness of fabricated bend shall not be ( Part I )-1977. less than that of the pipe to which it is to be welded. 3. MARKING

3.1 Each
information:

fabricated

90 bend fitting name

shall

be marked mark,

with the following and

a) Manufacturers

or identification

b) The size of the pressure ) to which

fitting and the pressure

the appropriate class (working rating of the fitting corresponds.

*Specification for fabricated high density polyethylene ( HDPE ) fittings for potable ~watersupplies: Part I General requirements. 4

IS: 8360 ( Part III ) - 1977

.TABLE

1 DIMENSIONS

FOR COVERALL LAYING FABRICATED 90 BENDS ( Clause 2.2.2 and Fig. 1 )

LENGTH

OF

SIZE

90"BEND,%ERALL
LAYING LENQTH,~ (2) mm

(1) mm

20
25 32 40 50 63 75 90 110 125 140 160 180 200 225 250 280 315 355 400 450 500 3.1.1

loo-& 3
LOO-& 3 100 & 100% lOO* 108&128f 154* 188 f 213 f 239 f 273 & 307 f 341 & 384 f 478 f 538 f 606 f 683 f 769 f 855 f 3 3 3 5 5 5 5 5

a
8 8 8 10 10 10 12 1.2 12 r2 with the

427 & 10

Standard

Each fabricated mark.

90 bend

fitting

may

also be marked

3.15 The use of the Standard Mark is govered by the provisions of the Bureau of Indian Standards Act, 1986 and the Rules and -Regulations made thereunder. The details of conditions under which the licence for the use of Standard Mark may be granted to manufacturers or producers may be obtained from the Bureau of Indian Standards.

I$ : 8360 ( Part III ) - 1977 ( Continued from page S, )

Mmbcrs SERI S. S.
CBHEDA

li%#ns~thg Small Scale Plastics Pipes and Fittings Manufacturers +sociation, Bombay Tarniapau Water Supply & Drainage Board, U. P. Jal Nigam, Lucknow Alternate ) Municipal Corporation of Delhi

Ckulep ENOINEIM CHIEF ENGINEEB SUPERINTENDINO ENQINEE~~ ( C~IEP ENQINEER ( WATTS ) DEPUTY CEIEI ENGINEER ( WATER ) ( Altematc ) SRXI J. M. DAVE

National Environmental Engineering Research Institute, Nagpur SHRI R. PARAMASIVA~~ ( Alternate ) EMCO General ( Plastic ) Industries (P) Ltd, SERI S. K. DEY Calcutta Central Building Research Institute ( CSIR ), SRRI R. K. JAIN Roorkee SERI S. P. CEAKRABARTI ( Alternate ) City & Industrial Development Corporation Ltd, SHRI A. R. KANGA Bombay National Chemical Laboratory ( CSIR ), Pune Dn S. L. KAPUR Imperial Chemical Industries ( India ) Ltd, Calcutta SBRI A. E. LADHABHOY DR V. B. V. RAJAN ( Akrnatm t nion Carbide India Ltd, Calcutta SHRI U. S. MAJMUNDAR SRRI S. P. KHURANA ( Alternate ) Directorate General of Technical Development k. PARIKSHIT Central Public Works Department SHIU G. S. RAO Ministry of Defence SERI K. C. S. RAO MAJ S. K. AQQARWAL ( Alternate ) Polyolefins Industries Ltd, Bombay SSRI P. B. RAO Sam V. DORAIRAJ ( Ahnatc ) National Buildings Organiaation, New Delhi SRRI 0. P. RATRA Public Health Engineering Department, Government REPRESENTATIVB of Haryana, Chandigarh Chemicals & Plastics ( India ) Ltd, Madras SHRI R. SIVARAMAKRISHNAN SEEI R. KALIDA~ ( dbdmat# ) Wavin India Ltd, Madras SERI G. K. SRINI~A~A~
SBRI K. R. RANQAIUJAN (

AILmate )

BUREAU

OF INDIAN STANDARDS

Headquarters: Manak Bhavan, 9 Bahadur Shah Zafar Marg, NEW DELHI 110002 Telephones: 323 0131,323 3375,323 9402 Fax : 91 11 3234062, 91 11 3239399, 91 11 3239382 Telegrams : Manaksanstha (Common to all Offices) Central Laboratory : Telephone Plot No. 20/9, Site IV, Sahibabad Industrial Area, Sahibabad 201010 Regional Offices: Central *Eastern 8-77 00 32

: Manak Bhavan, 9 Bahadur Shah Zafar Marg, NEW DELHI 110002 : l/14 CIT Scheme VII M, V.I.P. Road, Maniktola, CALCUTTA 700054
160022

32376

17

337 86 62 60 38 43 23523 15

Northern : SC0 335-336, Sector 34-A, CHANDIGARH Southern

: C.I.T. Campus, IV Cross Road, CHENNAI 600113

tWestern : Manakalaya, E9, Behind Marol Telephone Exchange, Andheri (East), MUMBAI 400093 Branch Offices:: Pushpak, Nurmohamed Shaikh Marg, Khanpur, AHMEDABAD $Peenya Industrial Area, 1 st Stage, Bangalore-Tumkur BANGALORE 560058 Road, 380001

832 92 95

550 13 48 839 49 55 55 40 21 40 36 27 21 01 41 8-28 88 01 8-71 19 96

Gangotri Complex, 5th Floor, Bhadbhada Road, T.T. Nagar, BHOPAL 462003 Plot No. 62-63, Unit VI, Ganga Nagar, BHUBANESHWAR Kalaikathir Buildings, 670 Avinashi Road, COIMBATORE Plot No. 43, Sector 16 A, Mathura Road, FARIDABAD Savitri Complex, 116 G.T. Road, GHAZIABAD 201001 781003 500001 751001 641037

121001

53/5 Ward No.29, R.G. Barua Road, 5th By-lane, GUWAHATI

54 11 37 201083 37 29 25 21 68 76

5-8-56C, L.N. Gupta Marg, Nampally Station Road, HYDERABAD E-52, Chitaranjan Marg, C- Scheme, JAIPUR 302001 117/418 B, Sarvodaya Nagar, KANPUR 208005 Seth Bhawan, 2nd Floor, LUCKNOW 226001 Behind Leela Cinema, Naval

Kishore

Road,

2389 23 52 51 71 26 23 05 32 36 35 621 17

NIT Building, Second Floor, Gokulpat Market, NAGPUR 440010 Patliputra Industrial Estate, PATNA 800013 Institution of Engineers (India) Building 1332 Shivaji Nagar, PUNE 411005 T.C. No. 14/l 421: University P. 0. Palayam, THlRUVANANlHAPURAM 695034

*Sales Cffice is at 5 Chowringhee Approach, P.O. Princep Street, CALCUTTA 700072 tSales Office is at Novelty Chambers, Grant Road, MUMBAI 400007 *Sales Cffice is at F Block, Unity Building, Narashimaraja Square, BANGALORE 560002

271085 309 65 28 222 39 71

Reprography Unit, BIS, New Delhi, India