Basics of Grinding

Training Objectives After watching the video and reviewing this printed material, the viewer will gain knowledge and understanding of the primary industrial grinding processes. cylindrical, internal, centerless and surface grinding are demonstrated types of abrasives and bonding methods are shown grinding wheel maintenance is explained specifics of surface finishing are detailed

The Grinding Process Grinding is a material removal and surface generation process used to shape and finish components made of metals and other materials. The precision and surface finish obtained through grinding can be up to ten times better than with either turning or milling. Grinding employs an abrasive product, usually a rotating wheel brought into controlled contact with a work surface. The grinding wheel is composed of abrasive grains held together in a binder. These abrasive grains act as cutting tools, removing tiny chips of material from the work. As these abrasive grains wear and become dull, the added resistance leads to fracture of the grains or weakening of their bond. The dull pieces break away, revealing sharp new grains that continue cutting. The requirements for efficient grinding include: abrasive components which are harder than the work shock- and heat-resistant abrasive wheels abrasives that are friable. That is, they are capable of controlled fracturing

Most abrasives used in industry are synthetic. Aluminum oxide is used in three quarters of all grinding operations, and is primarily used to grind ferrous metals. Next is silicon carbide, which is used for grinding softer, non-ferrous metals and high density materials, such as cemented carbide or ceramics. Superabrasives, namely cubic boron nitride or "CBN" and diamond, are used in about five percent of grinding. Hard ferrous materials are ground with "CBN", while non-ferrous materials and non-metals are best ground with diamond. The grain size of abrasive materials is important to the process. Large, coarse grains remove material faster, while smaller grains produce a finer finish. The binders that hold these abrasive grains together include: vitrified bonds, a glass-like bond formed of fused clay or feldspar organic bonds, from synthetic resins, rubber, or shellac metal or single-layer bond systems for superabrasives

Wheels are graded according their strength and wear resistance. A "hard" wheel is one that resists the separation of its individual grains. One that is too hard will wear slowly and present dulled grains to the work and overheat, affecting the final finish. If too soft a wheel is used, it will deteriorate quickly, requiring frequent replacement.

Fundamental Manufacturing Processes Video Series Study Guide

- 1 -

Basics of Grinding

Another aspect of grinding wheels is their pore structure or density, which refers to the porosity between individual grains. This pore structure creates spaces between the grains that provide coolant retention and areas for the chips to form. Dense wheels are best for harder materials, while more open densities are better for the softer metals. The three factors of grain size, bond type, and pore structure are closely related, and together determine how well a wheel will perform. Damaged wheels or even wheels suspected of being damaged should not be used. Safety steps for proper use of grinding wheels include, but are not limited to: always having machine guards in place before turning on a grinding wheel running wheels for at least one minute before actual work begins always using eye protection properly balancing and dressing wheels before use

Wheel dressing and truing is done with special tools designed for that purpose. Although wheel dressing is often done manually between work cycles, some grinding machines perform the dressing task automatically. The application of coolants to the grinding process is important. Coolants reduce grinding machine power requirements, maintain work quality, stabilize part dimensions, and insure longer wheel life. Coolants are either emulsions, synthetic lubricants or special grinding oils. Coolants are applied by either flooding the work area or by high pressure jet streams.

Types of Grinding There are many forms of grinding, but the four major industrial grinding processes are: cylindrical grinding internal grinding centerless grinding surface grinding

In cylindrical grinding, the workpiece rotates about a fixed axis and the surfaces machined are concentric to that axis of rotation. Cylindrical grinding produces an external surface that may be either straight, tapered, or contoured. The basic components of a cylindrical grinder include a wheelhead, which incorporate the spindle and drive motor; a cross-slide, that moves the wheelhead to and from the workpiece; a headstock, which locates, holds, and drives the workpiece; and a tailstock, which holds the other end of the work. Internal diameter or "I.D." grinders finish the inside of a previously drilled, reamed, or bored hole, using small grinding wheels at high RPM. The principle elements of a internal grinding machine are the workhead, which holds the work and has its own drive; and the wheelhead, which is the internal grinding spindle. In addition to the rotary motions of work and wheel, an internal grinder has a traverse movement to bring the wheel to and from the work zone, and a reciprocating spindle movement for both the wheel's approach to the work surface and for the feed movement of the wheel during grinding. Several

Fundamental Manufacturing Processes Video Series Study Guide

- 2 -

Basics of Grinding

different internal contours can be produced within a workpiece using I.D. grinding. In centerless grinding, the workpiece rotates between a grinding wheel and a regulating drive wheel. The work is supported from below by a fixed work-rest blade. The two basic modes of centerless grinding are "thru-feed" and "in-feed" or "plunge" mode. In the thru-feed mode, the work proceeds in the axial direction through the slowly narrowing gap between the grinding wheel and the regulating wheel. Work is advanced by the axial force exerted on it by the rotating surface of the regulating wheel. This is a highly productive form of grinding in that a number of workpieces can be ground simultaneously and in a continuous stream. The "infeed" mode is used for work with projecting heads that would prohibit "thru-feeding," the work is placed on the work-rest blade while one wheel is retracted and fed to an end stop. The wheel is then brought back, reducing the gap between the wheels, grinding the work. Surface grinding produces flat, angular, or contoured surfaces by feeding work in a horizontal plane beneath a rotating grinding wheel. Work is most often magnetically attached to the table, and may be ground by either a traversing or rotating movement of the table. Most surface grinding machines use a horizontal spindle which adjusts up and down allowing either the edge or the face of the wheel to contact the work. Workpiece surfaces produced by grinding are influenced by the following factors: workpiece material - harder materials allow finer finishes type of wheel - fine grains yield finer finishes dressing procedure - improperly dressed wheels will mar the work surface feed rate - finer finishes are obtained with slower feed rates machine rigidity - older, worn machines yield a poor quality finish wheel condition - clogged wheels cannot produce a good finish lubricant cleanliness - coolant filtration removes waste that could damage workpiece surface

Fundamental Manufacturing Processes Video Series Study Guide

- 3 -

Basics of Grinding

Review Questions 1. Friable means: a. capable of resisting heat buildup b. extremely porous c. capable of controlled fracturing d. tendency to clog wheel 2. The most commonly used abrasive is: a. silicon carbide b. aluminum oxide c. diamonds d. cubic boron nitride 3. Coolant retention is affected by the grinding wheels: a. hardness b. bond type c. grain size d. porosity 4. The cylindrical grinding methods finish: a. internal diameter surfaces b. horizontal surfaces c. external surfaces d. protruding surfaces 5. Internal grinding requires the grinding wheel to move: a. vertically up and down b. transversely c. longitudinally d. transversely and reciprocally 6. Workpiece movement in centerless grinding is accomplished by: a. a conveyor system b. air or hydraulic pressure c. regulating wheel axial force d. radial table tilt 7. Most surface grinding machines have spindles that are: a. vertical b. horizontal c. multiple d. orbiting 8. The most important aspect of grinding coolant is: a. cleanliness through filtration b. temperature control c. high pressure application d. compatibility with work material

Fundamental Manufacturing Processes Video Series Study Guide

- 4 -

Basics of Grinding

Answer Key 1. 2. 3. 4. 5. 6. 7. 8. c b d c d c b a

Fundamental Manufacturing Processes Video Series Study Guide

- 5 -

Basics of Grinding

Grinding Glossary abrasive Natural (sandstone, emery, corundum, diamonds) or artificial (silicon carbide, aluminum oxide) material used for making grinding wheels, sandpaper, abrasive cloth, and lapping compounds. A process related to grinding, which uses a thin, bonded abrasive wheel to cut materials for further processing. Disc wheel. A grinding wheel shaped like a straight wheel, but usually mounted on a plate for grinding on the side of the wheel. Any of several processes for removing scale and other surface contaminants using bonded grinding wheels, coated abrasives, honing stones or bonded abrasive sticks. Abrasive finishing leaves a surface with a controlled pattern of fine scratches- usually exhibiting a specific lay characteristic of the abrasive grit size and form, and type of equipment used. A process for finishing holes, inaccessible areas or restricted passages by clamping the part in a fixture, then extruding semisolid abrasive media through the passage. Often, multiple parts are loaded into a single fixture and finished simultaneously. Wheels of a hard abrasive, such as Carborundum, used for grinding.

abrasive cutoff

abrasive disc

abrasive finishing

abrasive flow machining

abrasive wheels

abrasive-wire bandsawing A variation of bandsawing that uses a smalldiameter wire with diamond, cubic boron nitride or aluminum oxide abrasives bonded to the surface as the cutting blade. Abrasive-wire bandsawing is an alternative to electrical discharge machining for producing dies, stripper plates, electrodes and cams from difficult-to-machine conductive and nonconductive materials. arbor The spindle of a grinding machine on which the wheel is mounted. The portion of the circumference of a grinding wheel in contact with the work. An adjustable stop that determines the amount of wheel withdrawal for dressing. Also called back-off stop.

arc of contact

back-off stop

Fundamental Manufacturing Processes Video Series Study Guide

- 6 -

Basics of Grinding

Balance (dynamic)

A wheel in static balance is also in dynamic balance if, upon rotating, there is no vibration or whip due to unequal distribution of weight throughout its mass. A grinding wheel is in static balance when, centered on a frictionless horizontal arbor, it remains at rest in any position. A small grinding machine for shaping and sharpening the cutting edges of tools. A pliable, compressible paper disc used between a grinding wheel and its mounting flanges. The material which cements the grains together making up the wheel. Bond may be rubber, shellac, resin, silicate, vitreous material, or metal, depending upon the abrasive material. Visible discoloration or subsurface damage from excessively high temperature produced by grinding. A trade name for an abrasive compounded of silicon and carbon (silicon carbide). Grinding in which the workpiece is supported on its OD and rotated around an axis created by this reference surface. The workpiece is free to shift, and if the support surface is the one being ground, the axis of rotation also shifts. Grinding by rotating the workpiece around a fixed centerline established by the chuck or centers in which it is held. The device that advances (crossfeeds) the grinding wheel to compensate for wear and dressing. Shaping stone or other hard nonmetallic material with a grinding wheel. The tendency of a grinding wheel to wear on its corner so that it does not grind up to a shoulder without leaving a fillet. A natural abrasive of the aluminum oxide type. A technique of plunge grinding with special design in which the table speeds are kept very low and the wheel is fed down to full depth of cut in one or two passes.

balance (static)

bench grinder

blotter

bond

burn

carborundum

centerless grinding

center-type grinding

compensator

coping

corner wear

corundum creep-feed grinding

Fundamental Manufacturing Processes Video Series Study Guide

- 7 -

Basics of Grinding

critical speed

1. That rotating speed beyond which the vibration of a spindle carrying an abrasive wheel or point would be hazardous. 2. A characteristic speed such that the predominant response of the system or rotor occurs at a resonance. In surface grinding, the amount of horizontal feed of the wheel across the table, or of the table across the wheel. The process of using rolls or special forms to form or dress the face of a grinding wheel to a specific contour. A form of boron nitride (BN), is a superabrasive crystal, second in hardness and abrasion resistance only to diamond. It is produced by a highpressure/high-temperature process similar to that used to make synthetic diamonds. CBN crystals are used most commonly in superabrasive wheels for precision grinding of steels and superalloys. The crystals are also compacted to produce polycrystalline cutting tools. A grinding wheel shaped like a cup or bowl. A thin abrasive wheel used to cut off or slot any material or part; usually made with an organic bond. The section removed by the milling cutter or grinding wheel in entering or leaving a flute. 1. A substance, generally liquid, used to enhance workpiece characteristics and reduce costs in a metalcutting operation. Cutting fluids may be oilbased fluids, water-oil emulsions, or chemicals in water solution. 2. Fluid used during grinding or dressing to cool, lubricate, and clean the work, wheel, and diamond. Sometimes called grinding fluid. Grinding the outer surface of a part that rotates on centers or in a chuck. Cycle in which dressing comes after finish grinding. Cycle in which dressing is done before finish grinding. A machine on which abrasive discs are used.

crossfeed (grinding)

crush dressing

cubic boron nitride (CBN)

cup wheel cutoff wheel

cutter sweep

cutting fluid

cylindrical grinding

DAF (dressing after finishing) DBF (dressing before finishing) disc grinder

Fundamental Manufacturing Processes Video Series Study Guide

- 8 -

Basics of Grinding

disc wheel

A grinding wheel shaped like a straight wheel, but usually mounted on a plate for grinding on the side of the wheel. Also referred to as abrasive disc. A grinding wheel shaped like a dish. In surface grinding, the rate at which the grinding wheel is fed into the work. The distance between successive diamond cuts for each revolution of the wheel; usually given in thousandths of an inch or millimeters. One dressing traverse of the diamond across the wheel. Time it takes to dress the length of the wheel. An adjustable stop that determines the amount of wheel withdrawal for dressing. Also called back-off stop. Device for manually or automatically dressing or trueing the grinding wheel. Also referred to as wheel dresser. Arm that carries the diamond holder. Stop pads or stop screws on the dresser to limit its travel relative to the wheel. Resharpening and renewing the cutting face of the wheel by removing or severing dull grains with a diamond or other type of dressing tool. Also referred to as trueing. Cycle in which dressing comes after finish grinding. Cycle in which dressing is done before finish grinding. In shoe centerless grinding, usually a flat plate attached to the work spindle and against which the part is held. It drives, but does not actually support the workpiece. Area in which driver and work touch each other. A method for deburring or chamfering sheet stock, tubing or rod ends, or workpiece edges by passing the stock across small grinding wheels or rotating angled cutters, or between pinch rolls.

dish wheel downfeed

dress lead

dress pass

dress rate dress stop

dresser

dresser arm dresser stop

dressing

dressing after finish (DAF) dressing before finish (DBF) driver

driver contact edging

Fundamental Manufacturing Processes Video Series Study Guide

- 9 -

Basics of Grinding

EDM grinding

This is done with an EDM power supply connected to a machine that resembles a surface grinder, but uses a wheel made from electrode material, usually graphite. A process similar to electrical discharge machining except that the electrode is a rotating wheel, generally graphite but sometimes brass. A nontraditional machining process in which a-c or pulsating d-c current is passed from a conductive grinding wheel made of bonded graphite to a positively charged workpiece through an electrolyte. There is no mechanical contact between wheel and workpiece. Rather, workpiece material is removed by the action of electrochemical grinding, and oxides formed by the electrochemical action are removed by intermittent random-spark discharges as in electrical discharge grinding.

electrical discharge grinding (EDG)

electrochemical discharge grinding (ECDG)

electrochemical grinding A special form of electrochemical machining that uses the combined actions of electrochemical attack (ECG) and abrasion to rapidly remove material; only 2 to 5% is done by the grinding wheel. electrochemical honing (ECH) A process similar to electrochemical grinding in which nonconductive honing stones rather than a grinding wheel provide the abrasive action. Electrochemical action removes about 90% of the workpiece metal; the honing stones cut most aggressively on high or tight areas to maintain size and surface finish. A natural abrasive of the aluminum oxide type. A compound (usually containing chlorine, sulfur, or phosphorus) which reacts with the surface of the metal or tool to form compounds (chlorides, sulfides, or phosphates) which have a low shear strength. These compounds can help provide longer tool and grinding wheel life in the moderate to heavy-duty operations. An objectionable spiral pattern produced on the work during grinding. A slow feed of the wheel away from the work. Used to improve the finish. In surface grinding, the rate at which the grinding wheel is fed into the work.

emery extreme pressure (EP) lubricant

feed lines

feed reversal

feed, down

Fundamental Manufacturing Processes Video Series Study Guide

- 10 -

Basics of Grinding

feed, index

In cylindrical grinding. an arrangement by which the amount of infeed is indicated on a dial. On most machines, the reference is to the diameter of the work; on a few machines, the reference is to the radius. Stop which limits crossfeed of wheel into work. The final cuts taken with a grinding wheel to obtain the accuracy and surface finish desired. The circular metal plates which retain and drive a grinding wheel. The tendency of abrasive grains to shatter under pressure. A wheel with a cutting surface too smooth (or dull) to grind efficiently. Glazing is caused by worn or improperly dressed grains. The strength of bonding of a grinding wheel; sometimes referred to as hardness. The tiny particles of abrasive which, with the bond, make up the wheel. Grains do the actual cutting. Also referred to as grit. The relative density of the abrasive particles in a grinding wheel. Usually referred to as structure and designated by a numeral in the wheel marking. A measure of grinding performance defined as the volume of metal removed divided by the volume of grinding wheel worn away in the process. Removing material from a workpiece with a grinding wheel or coated abrasives. Cutting fluid used in a grinding operation to cool, lubricate and clean the work and grinding wheel. Grinding wheel that retains its dull abrasive grains or is less friable. In cylindrical grinding. an arrangement by which the amount of infeed is indicated on a dial. On most machines, the reference is to the diameter of the work; on a few machines, the reference is to the radius. Designating disc, segmental, or cylindrical wheels with nuts embedded in the back to facilitate mounting on the grinding machine.

finish grind stop finishing

flanges

friability

glazed wheel

grade

grain

grain spacing

G-ratio

grinding

grinding fluid

hard-acting wheel

index feed

inserted nut

Fundamental Manufacturing Processes Video Series Study Guide

- 11 -

Basics of Grinding

internal grinding loading

Grinding the surface of a hole in the workpiece. A condition caused by grinding the wrong material with a grinding wheel or using too heavy a grinding action. A flat, smooth-surfaced work holding device which operates by magnetism to hold ferrous metal workpieces for grinding. Metal bond is used for diamond abrasives commonly used in the grinding of ceramics. There is also a trend to use metal-bonded wheels in the grinding of carbide with a technique known as single-pass, heavy-infeed grinding. Metal bonds are also used with aluminum oxide or diamond abrasive to provide conductive wheels for electrolytic grinding. Machining a groove or undercut in a shaft to permit mating parts to be screwed tightly against a shoulder or to provide clearance for the edge of a grinding wheel. A pivoted lever or sliding bolt that secures an automatic directional table control on a grinder. This is a synthetic-resin, organic bond mixed in powdered or liquid form with the abrasive grains. Resinoid-bonded wheels generally find their use in rough grinding and cutoff operations. They are also used in generating very fine finishes in roll grinding. Resin bonds are likely to be softened by prolonged exposure to water or water-based grinding fluids. Rubber-bond wheels are widely used in cutoff, centerless grinding, and polishing of drill flutes. Shellac is another organic bond used for wheels to produce high finishes on rolls, and for cutlery grinding. This bond is used to a very limited extent, primarily in operations in which the heat generated by grinding must be kept to a minimum, as in grinding edged tools. The volume of metal removed per unit of time per unit of effective grinding wheel width. The process of grinding flat surfaces on a surface grinding machine. With special setups, angular and form surfaces may also be ground.

magnetic chuck

metal bond

necking

pawl

resinoid bond

rubber bond

shellac bond

silicate bond

specific metal removal rate (q') surface grinding

Fundamental Manufacturing Processes Video Series Study Guide

- 12 -

Basics of Grinding

swarf

Metal fines and grinding wheel particles generated during grinding. The act of centering or aligning a workpiece or cutting tool so that an operation may be performed accurately. Also, correcting the eccentricity or out of round condition when dressing a grinding wheel. A versatile grinding machine designed to perform both internal and external grinding operations, including straight and tapered surfaces on tools and cutters. The chief ingredients of vitrified, or ceramic, bonds are clay and flux. The majority of grinding wheels in use today are vitrified wheels. They are strong and rigid and retain high strength at elevated temperatures, with the capability to remove stock, generate accurate geometry, and produce smooth finishes. Vitrified bonds are practically unaffected by water, oils, or ordinary temperature conditions. Poor shock resistance, however, inhibits their application when mechanical impact or large temperature differentials are likely to occur. The purpose of the bond is to hold the abrasive grains together to form a grinding wheel. Ideally, as the abrasive grains become dull and used, the bonding material breaks away, thus permitting the dull grains either to fracture or to be torn out so that, at all times, new, sharp abrasive grains are available for grinding the workpiece. Standard grinding-wheel bonds are vitrified bond, silicate, resinoid, rubber, shellac, oxychloride, and metal. A tool or device for dressing or trueing a grinding wheel.

trueing (truing)

universal grinder

vitrified bond

wheel bonds (grinding)

wheel dresser

Fundamental Manufacturing Processes Video Series Study Guide

- 13 -