Thrufeed Centerless Grinding

Saint-Gobain Abrasives
Home > Resources > Expertise > Thrufeed Centerless OD Grinding: Parameters and Troubleshooting
Thrufeed Centerless OD Grinding:

Parameters and Troubleshooting
On April 11 2017
On many work parts, the outside diameter (OD) needs to be

highly accurate. Tight tolerances are required for OD size,
roundness, high and low frequency lobe patterns and taper.
Thrufeed centerless OD grinding can achieve precise part
quality at an economical processing cost.
William Bednarski, Application Engineer, Saint-Gobain Abrasives

The original article was published in Cutting Tool Engineering Magazine, February 15, 2017.
Overview
As the name implies, centerless grinding involves the grinding of cylindrical parts without locating the
part on a specific center line between centers. The centerless process is commonly used for high volume
production, and it’s also easily used for low volume production because the machine setups are fairly
simple.
In thrufeed centerless OD grinding the workpiece passes

between two wheels, a grinding wheel and a regulating
wheel (as illustrated in the diagram, right). Both wheels
rotate in the same direction, but at much different speeds.
The purpose of the grinding wheel is to remove material
from the workpiece and improve part OD quality. The
regulating wheel acts like a brake, controlling the rotational
speed and thrufeed rate of the workpeice. An angular-
topped workrest blade supports the workpiece as it passes
Proper setup of centerless grinding
through the grinder between the grinding and regulating
with angular-topped blade, work
wheels. above center of wheels.
The abrasive types used in the grinding wheel are determined by the part material to be ground.
Aluminum oxide, ceramic aluminum oxide and CBN grains are typically used to grind ferrous materials.
Silicon carbide and diamond grains are typically used on non-ferrous materials. These grains are used in
vitrified or resin bonds to make a grinding wheel. Generally vitrified bonds are used to grind “weak”
configured parts that may deform when high grind force is applied. Resin bond grind wheels are used to
grind stronger parts like bars or solid rollers.
Regulating wheels are made in rubber, plastic or vitrified bonds. Some applications like tapered rollers
use special shaped, hardened steel regulating wheels.
Machine Setup Parameters

1. Top angle on workrest blade.
2. Relationship of the part center height above the wheel’s centerline dimension with the regulating
wheel diamond dresser offset dimension.
3. The regulating wheel angle of inclination or work feed angle to the regulating wheel dresser angle.
4. Entrance/exit guide alignment.
The top angle on the workrest blade helps with
the rounding action of the part. With increased
angle, quicker rounding occurs, but it also
weakens the blade rigidity. The most common
top angle used in centerless grinding is 30
degrees. As the diagram below indicates, lower
angles are used when grinding heavy workpieces,
which help minimize vibration. Workrest top
angles typically range from 45 degrees down to
20 degrees. Generally speaking, 30 degrees is a
good starting point for the majority of parts to be
thrufed centerless ground.
A majority of centerless grinders are set up with the work center height above the centerline of both
wheels. There are some applications like bar grinding that set up the bar center below the centerline of
the wheels to keep bar vibration low during the grinding process. We will focus on setups with the work
center above the centerline of the wheels, which is commonly called “work height above center.” Part
diameters 1½" or less should have the height above center dimension set at half the part diameter. Parts
greater than 1½" should be proportionally less for stability reasons. The purpose of the truing device on
the regulating wheel is to have the diamond follow a similar line of contact to the wheel that the parts will
follow. This will allow parts to enter and exit the grind zone in a straight line. So there is an important
relationship that ties the work height above center dimension to the regulating wheel diamond offset
setting. (See images below.)
Typically the diamond offset is set slightly less than the workpiece height above center dimension. It is
key to understand that this relationship influences the grind pattern and part contact to the grinding
wheel as parts pass through the grinder. It is very important to calculate the ratio of the regulating wheel
diameter to the workpeice diameter, or D/d. “D” is the regulating wheel diameter and “d” is the workpeice
diameter. Once you know this ratio, then you can use the “Truing Setting” chart (below) to determine the
correct truing angle and diamond offset.
The regulating wheel angle of inclination typically is in the +1 degree to +3 degree range. This angle,
along with regulating wheel speed (RPMs), determines the part thrufeed rate in inches per minute. This
setting also affects the distance a part will travel in one workpiece revolution. A lower angle means a
shorter travel distance and this affects grind force on the workpeice. So you can affect how a grinding
wheel performs by changing regulating wheel inclination and regulating wheel RPMs. Parts that have a
high diameter-to-length ratio, such as bearing rings, should have a lower regulating wheel angle of
inclination to help keep the parts stable as they travel through the grind zone. Proper settings allow the
workpieces to smoothly enter and exit the grind zone.
Typically there are adjustable guides on the entrance and

exit sides of the grind machine. The purpose of the guides
is to align the workpeices as the wheel goes in and comes
out of the grind zone. (See diagram, right.) It is important to
correctly align the guides located on the regulating wheel
side. The workpeices should smoothly transition between
guides and regulating wheel. Even a slight “bump” during
the transition can cause a defect to be ground into your
parts.
Proper guide alignment is important to avoid your parts from having a “barrel” or “hour glass” diameter
across the part length. The illustration below shows how misaligned guides could affect part quality.
Be sure to inspect all the tooling used in the centerless grinder, and make sure all tooling is in good
condition. You can have a good machine setup, but if the diamond tools are worn, they will cause dull
dress condition on your wheels and generate poor part quality. Paying close attention to your tooling
condition and machine setup will ensure that your grinder will produce excellent part quality at low
manufacturing costs.
Related / Latest Stories

How Contour Grinding Evaluating Wide
Puts People Back on Sanding Belts
Their Feet FDMC Article on Evaluating
The quality of knee implants Wide Sanding Belts | First
depends on the shape, accuracy, Published September 16, 2016
design, and finish of the model Read more >
from the factory. Learn how
contour grinding plays a critical
role in creating a comfortable
and effective implant.
Read more >

Removing Roadblocks
to Optimizing Newly
Installed Grinding
Processes
Use the strategies in William
Plager’s article, published in
May 2016 CTE Magazine, to
remove roadblocks in the
grinding processes involved in
high volume lines producing
complex parts.
Read more >
ABOUT US
Norton has been delivering abrasive
solutions to our customers for 130 years
and counting. We care to deliver right
choices that matter to your market and
application...
Read More >
© Saint-Gobain 2020
Launch Tag

Thrufeed Centerless Grinding

Uploaded by

Copyright:

Available Formats

Thrufeed Centerless Grinding

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Thrufeed Centerless Grinding

Uploaded by

Copyright:

Available Formats

Saint-Gobain Abrasives

Thrufeed Centerless OD Grinding:

On many work parts, the outside diameter (OD) needs to be

William Bednarski, Application Engineer, Saint-Gobain Abrasives

In thrufeed centerless OD grinding the workpiece passes

Machine Setup Parameters

Typically there are adjustable guides on the entrance and

Related / Latest Stories

Read more >

Read more >

Read More >

You might also like