S/M No.

: TCN001PEF0

Service Manual
Color Television

CHASSIS : CN-001P
Model : DTQ-14Z5SC

Caution
: In this Manual, some parts can be changed for improving. their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List)in Service Information Center.

AUG. 2005

TABLE OF CONTENTS
SAFETY PRECAUTIONS
PRODUCT SAFTY SERVICING GUIDELINES FOR AUDIO-VIDEO PRODUCS PRODUCT SAFTY SERVICING GUIDELINES FOR COLOR TELEVISION RECEIVERS

2
2 3

SPECIFICATIONS BLOCK DIAGRAM ALIGNMENT INSTRUCTIONS

SERVICE MODE ADJUSTMENTS ASSEMBLY ADJUSTMENTS PARENTAL CONTROL PASSWORD SETTINGS

5 6 7
7 9 12

VOLTAGE CHART SCHEMATIC DIAGRAM EXPLODED VIEW PRINTED CIRCUIT BOARD ELECTRICAL PARTS LIST

13 15 16 17 19

APPENDIX(Appendix is provide only by internet [http://svc,dwe.co.kr])

WAVEFORMS IC DESCRIPTION TROUBLE SHOOTING GUIDE
NO POWER NO PICTURE NO SOUND CH DONT MEMORY or CH SKIP NO COLOR NO VERTICAL DEFLECTION NO ON SCREEN DISPLY REMOTE CONTROL DOES NOT OPERATE

24 27 31
31 32 33 34 35 35 36 36

PRODUCT SAFETY SERVICING GUIDELINES FOR AUDIO - VIDEO PRODUCTS

CAUTION : DO NOT ATTEMPT TO MODIFY THIS PRODUCT IN ANY WAY. NEVER PERFORM CUSTOMIZED INSTALLATIONS WITHOUT MANUFACTURER'S APPROVAL. UNAUTHORIZED MODIFICATIONS WILL NOT ONLY VOID THE WARRANTY, BUT MAY LEAD TO YOUR BEING LIABLE FOR ANT RESULTING PROPERTY DAMAGE OR USER INJURY. SERVICE WORK SHOULD BE PERFORMED ONLY AFTER YOU ARE THOROUGHLY FAMILIAR WITH ALL OF THE FOLLOWING SAFETY CHECKS AND SERVICING GUIDELINES. TO DO OTHERWISE, INCREASES THE RISK OF POTENTIAL HAZARDS AND INJURY TO THE USER. WHILE SERVICING, USE AN ISOLATION TRANSFORMER FOR PROTECTION FROM A.C. LINE SHOCK. SAFETY CHECKS
AFTER THE ORIGINAL SERVICE PROBLEM HAS BEEN CORRECTED, A CHECK SHOULD BE MADE OF THE FOLLOWING:

SUBJECT : X-RADIATION
1. BE SURE PROCEDURES AND INSTRUCTIONS TO ALL SERVICE PERSONNEL COVER THE SUBJECT OF X-RADIATION. THE ONLY POTENTIAL SOURCE OF X-RAYS IN CURRENT T.V. RECEIVERS IS THE PICTURE TUBE. HOWEVER, THIS TUBE DOES NOT EMIT X-RAYS WHEN THE HIGH VOLTAGE IS AT THE FACTORY SPECIFIED LEVEL. THE PROPER VALUE IS GIVEN IN THE APPLICABLE SCHEMATIC. OPERATION AT HIGHER VOLTAGES MAY CAUSE A FAILURE OF THE PICTURE TUBE OR HIGH VOLTAGE SUPPLY AND UNDER CERTAIN CIRCUMSTANCES, AMY PRODUCE RADIATION IN EXCESS OF DESIRABLE LEVELS. 2. ONLY FACTORY SPECIFIED C.R.T ANODE CONNECTORS MUST BE USED. DEGAUSSING SHIELDS ALSO SERVE AS X-RAY SHIELD IN COLOR SETS. ALWAYS RE-INSTALL THEM. 3. IT IS ESSENTIAL THAT SERVICE PERSONNEL HAVE AVAILABLE AN ACCURATE AND RELIABLE HIGH VOLTAGE METER. THE CALIBRATION OF THE METER SHOULD BE CHECKED PERIODICALLY AGAINST A REFERENCE STANDARD. SUCH AS THE ONE AVAILABLE AT YOUR DISTRIBUTOR. 4. WHEN THE HIGH VOLTAGE CIRCUITRY IS OPERATING PROPERLY THERE IS NO POSSIBILITY OF AN X-RADIATION PROBLEM. EVERY TIME A COLOR CHASSIS IS SERVICED, THE BRIGHTNESS SHOULD BE RUN UP AND DOWN WHILE MONITORING THE HIGH VOLTAGE WITH A METER TO BE CERTAIN THAT THE HIGH VOLTAGE DOES NOT EXCEED THE SPECIFIED VALUE AND THAT IT IS REGULATING CORRECTLY. WE SUGGEST THAT YOU AND YOUR SERVICE ORGANIZATION REVIEW TEST PROCEDURES SO THAT VOLTAGE REGULATION IS ALWAYS CHECKED AS A STANDARD SERVICING PROCEDURE, AND THAT THE HIGH VOLTAGE READING BE RECORDED ON EACH CUSTOMER S INVOICE. 5. WHEN TROUBLESHOOTING AND MAKING TEST MEASUREMENTS IN A PRODUCT WITH A PROBLEM OF EXCESSIVE HIGH VOLTAGE, AVOID BEING UNNECESSARILY CLOSE TO THE PICTURE TUBE AND THE HIGH VOLTAGE SUPPLY. DO NOT OPERATE THE PRODUCT LONGER THAN IS NECESSARY TO LOCATE THE CAUSE OF EXCESSIVE VOLTAGE. 6. REFER TO HV, B+ AND SHUTDOWN ADJUSTMENT PROCEDURES DESCRIBED IN THE APPROPRIATE SCHEMATIC AND DIAGRAMS (WHERE USED).

SUBJECT:FIRE & SHOCK HAZARD

1. BE SURE THAT ALL COMPONENTS ARE POSITIONED IN SUCH A WAY AS TO AVOID POSSIBILITY OF ADJACENT COMPONENT SHORTS. THIS IS ESPECIALLY IMPORTANT ON THOSE MODULES WHICH ARE TRANSPORTED TO AND FROM THE REPAIR SHOP. 2. NEVER RELEASE A REPAIR UNLESS ALL PROTECTIVE DEVICES SUCH AS INSULATORS, BARRIERS, COVERS, SHIELDS, STRAIN RELIEFS, POWER SUPPLY CORDS, AND OTHER HARDWARE HAVE BEEN REINSTALLED PER ORIGINAL DESIGN. BE SURE, THAT THE SAFETY PURPOSE OF THE POLARIZED LINE PLUG HAS NOT BEEN DEFEATED. 3. SOLDERING MUST BE INSPECTED TO DISCOVER POSSIBLE COLD SOLDER JOINTS, SOLDER SPLASHES OF SHARP SOLDER POINTS. BE CERTAIN TO REMOVE ALL LOOSE FOREIGN PARTICLES. 4. CHECK FOR PHYSICAL EVIDENCE OF DAMAGE OR DETERIORATION TO PARTS AND COMPONENTS, FOR FRAYED LEADS, DAMAGED INSULATION (INCLUDING A.C. CORD), AND REPLACE IF NECESSARY. FOLLOW ORIGINAL LAYOUT, LEAD LENGTH AND DRESS. 5. NO LEAD OR COMPONENT SHOULD TOUCH A RECEIVING TUBE OR A RESISTOR RATED AT 1 WATT OR MORE. LEAD TENSION AROUND PROTRUDING METAL SURFACES MUST BE AVOIDED. 6. ALL CRITICAL COMPONENTS SUCH AS FUSES, FLAMEPROOF RESISTOR, CAPACITORS, ETC. MUST BE REPLACED WITH EXACT FACTORY TYPES. DO NOT USE REPLACEMENT COMPONENTS OTHER THAN THOSE SPECIFIED OR MAKE UNRECOMMENDED CIRCUIT MODIFICATIONS. 7. AFTER RE-ASSEMBLY OF THE STE ALWAYS PERFORM AN A.C. LEAKAGE TEST ON ALL EXPOSED METALLIC PARTS OF THE CABINET. (THE CHANNEL SELECTOR KNOB, ANTENNA TERMINALS, HANDLE AND SCREWS) TO BE SURE THE SET IS SAFE TO OPERATE WITHOUT DANGER OF ELECTRICAL SHOCK. DO NOT USE A LINE ISOLATION TRANSFORMER DURING THIS TEST USE AN A.C. VOLTMETER, HAVING 5000 OHMS PER VOLT OR MORE SENSITIVITY, IN THE FOLLOWING MANNER : CONNECT A 1500 OHM 10 WATT RESISTOR, PARALLELED BY A .15 MFD. 150V A.C. TYPE CAPACITOR BETWEEN A KNOWN GOOD EARTH GROUND (WATER POPE, CONDUIT, ETC.) AND THE EXPOSED METALLIC PARTS, ONE AT A TIME. MEASURE THE A.C. VOLTAGE ACROSS THE COMBINATION OF 1500 OHM RESISTOR AND .15 MFD CAPACITOR. REVERSE THE A.C. PLUG AND REPEAT A.C. VOLTAGE MEASUREMENTS FOR EACH EXPOSED METALLIC PART. VOLTAGE MEASURED MUST NOT EXCEED .75 VOLTS R.M.S THIS CORRESPONDS TO 0.5 MILLIAMP A.C. NAY VALUE EXCEEDING THIS LIMIT CONSTITUTES A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED IMMEDIATELY.

SUBJECT : IMPLOSION
1. ALL DIRECT VIEWED PICTURE TUBES ARE EQUIPPED WITH AN INTEGRA IMPLOSION PROTECTION SYSTEM. BUT CARE SHOULD BE TAKEN TO AVOID DAMAGE DURING INSTALLATION. AVOID SCRATCHING THE TUBE. OF SCRATCHED REPLACE IT. 2. USE ONLY RECOMMENDED FACTORY REPLACEMENT TUBES.

SUBJECT : TIPS ON PROPER INSTALLATION

1. NEVER INSTALL ANY PRODUCT IN A CLOSED-IN RECESS, CUBBYHOLE OR CLOSELY FITTING SHELF SPACE, OVER OR CLOSE TO HEAT DUCT, OR IN THE PATH OF HEATED AIR FLOW. 2. AVOID CONDITIONS OF HIGH HUMIDITY SUCH AS: OUTDOOR PATIO INSTALLATIONS WHERE DEW IS A FACTOR, NEAR STEAM RADIATORS WHERE STEAM LEAKAGE IS A FACTOR, ETC. 3. AVOID PLACEMENT WHERE DRAPERIES MAY OBSTRUCT REAR VENTING. THE CUSTOMER SHOULD ALSO AVOID THE USE OF DECORATIVE SCARVES OR OTHER COVERINGS WHICH MIGHT OBSTRUCT VENTILATION. 4. WALL AND SHELF MOUNTED INSTALLATIONS USING A COMMERCIAL MOUNTING KIT, MUST FOLLOW THE FACTORY APPROVED MOUNTING INSTRUCTIONS. A PRODUCT MOUNTED TO A SHELF OR PLATFORM MUST RETAIN ITS ORIGINAL FEET (OR THE EQUIVALENT THICKNESS IN SPACERS)TO PROVIDE ADEQUATE AIR FLOW ACROSS THE BOTTOM, BOLTS OR SCREWS USED FOR FASTENERS MUST NOT TOUCH ANY PARTS OR WIRING. PERFORM LEAKAGE TEST ON CUSTOMIZED INSTALLATIONS. 5. CAUTION CUSTOMERS AGAINST THE MOUNTING OF A PRODUCT ON SLOPING SHELF OR A TILTED POSITION, UNLESS THE PRODUCT IS PROPERLY SECURED. 6. A PRODUCT ON A ROLL-ABOUT CART SHOULD BE STABLE ON ITS MOUNTING TO THE CART. CAUTION THE CUSTOMER ON THE HAZARDS OF TRYING TO ROLL A CART WITH SMALL CASTERS ACROSS THRESHOLDS OR DEEP PILE CARPETS. 7. CAUTION CUSTOMERS AGAINST THE USE OF A CART OR STAND WHICH HAS NOT BEEN LISTED BY UNDERWRITERS LABORATORIES. INC. FOR USE WITH THEIR SPECIFIC MODEL OF TELEVISION RECEIVER OR GENERICALLY APPROVED FOR USE WITH T.V.S OF THE SAME OR LARGER SCREEN SIZE. 8. CAUTION CUSTOMERS AGAINST THE USE OF EXTENSION CORDS, EXPLAIN THAT A FOREST OF EXTENSIONS SPROUTING FROM A SINGLE OUTLET CAN LEAD TO DISASTROUS CONSEQUENCES TO HOME AND FAMILY.

A.C. VOLTMETER

0.15 uF

GOOD EARTH GROUND SUCH AS THE WATER PIPE, CONDUIT, ETC.

1500

OHM

10WATT

PLACE THIS PROBE ON EACH EXPOSED METAL PART

SUBJECT : GRAPHIC SYMBOLS

THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE SERVICE PERSONNEL TO THE PRESENCE OF UNINSULATED DANGEROUS VOLTAGE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK. THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE SERVICE PERSONNEL TO THE PRESENCE OF IMPORTANT SAFETY INFORMATION ON SERVICE LITERATURE.

PRODUCT SAFETY SERVICING GUIDELINES FOR COLOR TELEVISION RECEIVERS

CAUTION : Do not attempt to modify this product in any way. Unauthorized modifications will not only void the warranty, but may lead to your being liable for any resulting property damage or user injury. Service work should be performed only after you are thoroughly familiar with all of the following safety checks and servicing guidelines. To do otherwise, increases the risk of potential hazards and injury to the user.

GRAPHIC SYMBOLS :
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the service personnel to the presence of uninsulated dangerous voltage that may be of sufficienty magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the service personnel to the presence of important safety information in service literature. Fuse symbol is printed on pcb adjacent to the fuse, with RISK OF FIRE REPLACE FUSE AS MARKED . The symbol is explained in the service manual with the following wording or equivalent. CAUTION : FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH SAME TYPE (4A, 125V) and ATTENTION: AFIN D ASSU UNE PROTECTION PERMANENTE CONTRE LES RISQUES D INCENDIE, REMPLACER UNIQUEMENT PAR UN FUSIBLE DE MEME TYPE ET DE 4A, 125V .

SAFETY CHECKS
After the original service problem has been corrected, a check should be made of the following:

SUBJECT : FIRE & SHOCK HAZARD

1. Be sure that all components are positioned in such a way as to avoid possibility of adjacent component shorts. This is especially important on those chassis which are transported to and from the repair shop. 2. Never release a repair unless all protective devices such as insulators, barriers, covers, shields, strain reliefs, and other hardware have been reinstalled per original design. 3. Soldering must be inspected to discover possible cold solder joints, frayed leads, damaged insulation (including A.C. cord), solder splashes or sharp solder points. Be certain to remove all loose foreign particals. 4. Check for physical evidence of damage or deterioration to parts and components, and replace if necessary follow original layout, lead length and dress. 5. No leads or components should touch a receiving tube or a resistor rated at 1 watt or more. Lead tension around protruding metal surfaces must be avoided. 6. All critical components such as fuses, flameproof resistors, capacitors, etc. must be replaced with exact factory types. Do not use replacement components other than those specified or make unrecommended circuit modifications. 7. After re-assembly of the set always perform an A.C. leakage test on all exposed metallic parts of the cabinet, (the channel selector knob, antenna terminals, handle and screws) to be sure the set is safe to operate without danger of electrical shock. Do not use a line isolation transformer during this test. Use an A.C. voltmeter, having 5000 ohms per volt or more sensitivity, in the following manner : connect a 1500 ohm 10 watt resistor, paralleled by a 15 mfd. 150V A.C. type capacitor between a known good earth ground (9water pipe, conduit, etc.) and the exposed metallic parts, one at a time. Measure the A.C. voltage across the combination of 1500 ohm resistor and 0.15 MFD capacitor. Reverse the A.C. plug and repeat A.C. voltage measurements for each exposed metallic part. Voltage measured must not exceed 0.75 volts R.M.S. This corresponds to 0.5 milliamp A.C. Any value exceeding this limit constitutes a potential shock hazard and must be corrected immediately.
A.C. VOLTMETER

SUBJECT : X-RADIATION
1. Be sure procedures and instructions to all service personnel cover the subject of X-rays in current T.V. receivers is the picture tube. However, this tube does not emit X-rays when the high voltage is at the factory specified level. The proper value is given in the applicable schematic. Operation at higher voltages may cause a failure of the picture tube or high voltage supply and, under certain circumstances, may produce radiation in excess of desirable levels. 2. Only factory specified C.R.T. anode connectors must be used. Degaussing shields also serve as X-ray shield in color sets. Always re-install them. 3. It is essential that the serviceman has available an accurate and reliable high voltage meter. The calibration of the meter should be checked perio - dically against a reference standard. Such as the one available at your distributor. 4. When the high voltage circuitry is operating properly there is no possibility of an X-radiation problem. Every time a color chassis is serviced, the brightness should be run up and down while monitoring the high voltage with a meter to be certain that the high voltage does not exceed the specified value and that it is regulating correctly. We suggest that you and your service organization review test procedures so that voltage regulation is always checked as a standard servicing procedure. And that the high voltage reading be recorded on each customer s invoice. 5. When troubleshooting and making test measurements in a receiver with a problem of excessive high voltage, avoid being unnecessarily close to the picture tub eand the high voltage compartment. Do not operate the chassis longer than is necessary to locate the cause of excessive voltage. 6. Refer to HV, B+and Shutdown adjustment procedures described in the appropriate schematic and diagrams(where used).

Good earth ground, such as the water pipe, conduit, etc.

0.15 uF

1500

OHM

10WATT

Place this probe on each exposed metal part.

SUBJECT : IMPLOSION
1. All direct viewed picture tubes are equipped with an integral implosion protection system, but care should be taken to avoid damage during installation. Avoid scratching the tube. If scratched, replace it. 2. Use only recommended factory replacement tubes.

SUBJECT : TIPS ON PROPER INSTALLATION

1. Never install any receiver in closed-in recess, cubbyhole or closely fitting shelf space over, or close to heat duct, or in the path of heated air flow. 2. Avoid conditions of high humidity such as : Outdoor patio installations where dew is a factor. Near steam radiators where steam leakage is a factor, etc. 3. Avoid placement where draperies may obstruct rear venting. The customer should also avoid the use of decorative scarves or other coverings which might obstruct ventilation.

4. Wall and shelf mounted installations using a commercial mounting kit, must follow the factory approved mounting instructions. A receiver mounted to a shelf or platform must retain its original feet(or the equivalent thickness in spacers) to provide adequate are flow across the bottom, bolts or screws used for fasteners must not touch and parts or wiring. Perform leakage test on customized installations. 5. Caution customers against the mounting of a receiver on sloping shelf or a tilted position, unless the receiver is properly secured. 6. A receiver on a roll-about cart should be stable on its mounting to the cart. Caution the customer on the hazards of trying to roll a cart with small casters across thresholds or deep pile carpets. 7. Caution customers against the use of a cart or stand which has not been listed by underwriters laboratories, inc. For use with their specific model of television receiver or generically approved for use with T.V. s of the same or larger screen size.

SPECIFICATIONS

MODEL ITEM TV STANDARD POWER INPUT

POWER CONSUMTION

DTQ -14Z5SC NTSC - M

REMARK

AC 120V / 60 Hz 55 WATTS FREQUENCY SYNTHESIZER(FS) TUNING SYSTEM VHF : 2 ~ 13 (12) UHF : 14 ~ 69 (56) CATV : 1 ~ 125 (125)

TUNING SYSTEM TUNING RANGES

SOUND OUTPUT SPEAKER ANTENA INPUT IMPEDANCE AUXILIARY INPUT TERMINAL INTERMEDIATE FREQUENCIES

1.3W 3W 8 ohm 75ohm Unbalanced

Front : Video, Audio Picture IF Carrier Frequency : 45.75MHz Sound IF Carrier Frequency : 41.25MHz
Color Sub- Carrier Frequency : 3.579545MHz

REMOTE CONTROL SPECIAL FUNCTIONS

R-48C04 3-Language OSD With CAPTION Wake - up On/Off Time Sleep Timer Power Restore

BLOCK DIAGRAM

ALIGNMENT INSTRUCTIONS
1. SERVICE MODE ADJUSTMENTS
Follow the steps below whenever service adjustment is required. See Table- A and Table- B to determine if service adjustments are required. 1) How to enter the service mode using the user remote control. Turn the set on. Direct the remote control to the reception window of TV. Push buttons of remote control in sequence as follows. 1 MUTE DISPLAY MUTE Then, the screen will appear as follows.

S2
S5 S6 S7 S8 S9 S11 S12

SCRN
IFC GEO PTRN NORMAL W/B DP LA76950 FACT

Using the channel up or channel down button, select the item you wish to adjust.

(The color of selected item turns into the red.)

Press the volume up or down button to enter in the service mode you wish to adjust.

2) How to memorize the adjusted values in the service mode. Must press DISPLAY button the state which the screen is displaying each of service menus after all adjustments are completed each of all service menu. Table-A : Adjust the values of service mode when a part is replaced.
PART REPLACED
I701 (U-COM) I101 (MAIN)

ADJUSTMENT NECESSARY UNNECESSARY

O O Data is stored in I703.

NOTES

Initial setting values are written from I701. Adjusting Items I703 (EEPROM) O
S5 S6 S8 S9 RFAGCD H.SHIFT/V.SHIFT/V.SIZE RD/BD/RB/GB/BB Brightness

CRT

Adjust items related to picture tube only.(White Balance adjustment)

ALIGNMENT INSTRUCTIONS
Table-B

ALIGNMENT INSTRUCTIONS

2. ASSEMBLY ADJUSTMENTS
1) SCREEN ADJUSTMENT (S2) Enter the service mode and select service adjustment S2. You cna see the one horizontal line on the screen. Adjust the Screen Control Volume (located on FBT) so that the horizontal line onscreen may be disappeared. Press the volume up or down button to exit in the screen adjustment mode.

NOTE
IN THE SCREEN ADJUSTMENT MODE, DONT PRESS OTHER BUTTONS EXCEPT VOLUME UP OR DOWN BUTTON.

2) FOCUS ADJUSTMENT Turn in a local station and adjust the Focus Control knob (located on FBT) for best picture details at high light condition. 3) RF AGC DELAY ADJUSTMENT (S5) Receive a good local channel. Enter the service mode and select service adjustment S5. You can see the OSD as shown in below.

IF CONTROL AUTO RFAGC VIDEO RFAGCD AGC ST AGC POINT AGC CH NO NO SD POWER OFF

START 4 35 55 3.75 10 NO

Select RFAGCD item, press the volume up or down button until noise or beat in picture disappears. Press the DISPLAY button to memorize the data.

ALIGNMENT INSTRUCTIONS
4) GEOMETRIC ADJUSTMENTS (S6) Enter the service mode and select service adjustment S6.

You can see the OSD as shown in below.

GEOMETRY H. SHIFT V. SHIFT V. SIZE V. SC V.LIN MOVE V.DC ADJUST 18 16 38 53 11 2

RECALL:SET

4-1. Horizontal SHIFT Adjustment Select H.SHIFT item, adjust H.SHIFT data value to obtain proper horizontal centering of the internal cross pattern at the left and right of the screen. 4-2. Vertical SHIFT Adjustment Select V.SHIFT item, adjust V.SHIFT data value to center the raster properly on thescreen. 4-3. Vertical Size Adjustment Select V.SIZE item, adjust V.SIZE data value to proper vertical size as follows.

10

ALIGNMENT INSTRUCTIONS
5) WHITE BALANCE ADJUSTMENT(S8) Receive a good local channel. Enter the service mode and select service adjustment S8. You can see the OSD as shown in below.
RD GD BD RB GB BB
MOVE

96 10 REF 96 128 128 128

ADJUST RECALL : SET

Using volume up or volume down, adjust service adjustment data of RD/GD/BD and RB/GB/BB until a good gray

scale with normal whites is obtained.ALIGNMENT INSTRUCTIONS Press the DISPLAY button to memorize the data. 6) DIGITAL PRESET(D.P) ADJUSTMENTS(S9) SUBBRIGHTNESS ADJUSTMENT Receive a good local channel. Enter the service mode and select service adjustment S9. You can see the OSD as shoown in below.
D.P. Subbrightness Contrast Tint Color Sharp
MOVE

64 8 44 15 15
ADJUST RECALL : SET

Select Subbrightness item, adjust Subbrightness data value to obtain normal brightness level. Press the DISPLAY button to memorize the data.

Conttrast Fixed value = 8 Tint Fixed value = 44 Color Fixed value = 15 Sharp Fixed value = 15 7) FACTORY OUTGOING MODE (S12 : FACT) If you select the S12, then the set becomes factory outgoing status. You can see the OSD outgoing OK

11

ALIGNMENT INSTRUCTIONS

3. PARENTAL CONTROL PASSWORD SETTINGS

If user forget Parental Control Password as follows. 1) CHANGE THE PASSWORD. Turn the set on. Direct the remote control to the reception window of your TV/VCR Using the MENU buttons, select the Special menu. Using the the channel up ( ) or down ( ) duttons, select prental control. Using the volume up ( ), set the password Menu. Push buttons of remote control in sequence as follows. 2 2 1 1 Parental control password is reset. Using the 0~9 buttons, enter the password. Using the 0~9 buttons, repeat the password.
Special
Closed Caption : OFF CC on Mute : OFF Power Restore : OFF Parental Control Select Adjust n Exit [0 - 9] : Adjust n Prev. Enter the Password ####

Parental control

Parental control
Enter a New Password

Parental control
Repeat the Password ####

[0 - 9] : Adjust

n Prev.

[0 - 9] : Adjust

n Exit

2) RESET THE PASSWORD Turn the set on. Direct the remote control to the reception window of your TV/VCR. Push buttons of remote control in sequence as follows. 1 MUTE DISPLAY MUTE Then, the screen will appear as follows.

S2 S5 S6 S7 S8 S9 S11 S12

SCRN IFC GEO PTRN NORMAL W/B DP LA76950 FACT

Using the channel up ( ) or down ( ) buttons, select S12 FACT. Press the volume up ( ) button, the set becomes factory outgoing status. Parental control password is reset. Using the MENU buttons, select the parental control menu, set the new password.

12

VOLTAGE CHART
L/C I501 PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 MODE ON 2.46 2.55 3.12 2.39 1.98 1.99 2.27 4.89 2.2 3.28 8.17 2.46 2.43 2.47 0 2.18 2.37 1.66 5.07 0 0.57 0 0.5 0.49 0 5.01 0 0 0 4.8 5.03 5.03 1.58 2.55 5.02 5.02 1.95 0 0 4.46 2.84 0 0 0.75 2.42 2.62 0 2.62 OFF 0.07 0 0.04 0 0 0 0 0 0.46 0.05 0.07 0.08 0.06 0.05 0 0 0 0 0 0 0 0 0.33 0.33 0 4.94 4.86 0 0.27 0 4.96 4.96 1.55 2.5 4.96 4.95 0 0 0 4.44 2.73 0 0 0 0.03 0.04 0 0.04 L/C PIN 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 L/C I301 PIN 1 2 3 4 5 6 7 PIN 1 2 3 4 5 6 7 8 PIN 1 2 3 1 2 3 4 5 6 7 8 MODE OFF 0.03 0.05 0.04 0.06 0 0.3 0.07 0 0.07 0 0.04 0 0.06 0 0 0 MODE ON OFF 2.24 0 26.2 0 2.14 0 0 0 12.61 0 26.7 3.12 2.24 0 MODE ON OFF 6.12 0.25 13.3 8.94 1.6 0 0 0 0 1.06 0 0 1.59 0 0 0 MODE ON OFF 9.23 6.41 0 0 2.495 1.99 0 0 0 0 0 0 0 0 5.01 4.97 5.01 4.97 0 0 5.01 4.97 ON 0.43 2.69 0 1.9 3.38 2.49 4.88 2.81 2.43 2.34 2.48 2.46 1.96 0 2.75 2.75

L/C I601

L/C 1803

I703

13

VOLTAGE CHART

L/C I801

PIN 1 2 3 4 5 6 7

MODE ON 1.58 NC 0 20.4 0.18 0.9 1.74 OFF 167.8 NC 0 11.7 0.08 1.57 0.2

L/C I401

PIN 1 2 3

MODE ON 8.46 0 5.03 OFF 0 0 0

L/C Q401

PIN E C B E C B E C B E C B E C B E C B

Q404

Q450

Q510

Q575

Q805

MODE ON OFF 0 0 2.26 35.2 0.3 0 0 0 10 0.07 0 0 0 0 0.57 0 0.02 0.64 3.2 0 0 0 3.8 0.07 10 0.43 0.5 0.45 10.33 0 5.01 4.98 13.3 8.93 5.63 5.58

L/C Q806

PIN E C B E C B E C B E C B E C B

MODE ON 5.01 5.11 4.52 0 6.36 0.02 0 0 0.69 0 0 0.69 1.44 0 0.72 OFF 4.98 0 4.95 0 0.02 0.65 0 7.3 0 0 4.94 0 0 0 0

Q835

Q845

Q848

Q977

14

15

EXPLODED VIEW

16

17

18

ELECTRICAL PARTS LIST

CAUTION is a safety patt, so it must be used the same part. is a recommendable part for essential stock.
LOC
ZZ100 ZZ110 10000 M821 ZZ120 M211 M211B ZZ130 10 M801 M811 M821 ZZ131 ZZ132 ZZ140 40 CRT1 V01 V04 V05 V06 V901 M201A M201B M211A M541 M601 M681 ZZ200 M201 M481 M481A ZZ202 PA601 SP01 ZZ290 C404 C801 C804 I301 00001 0000A 0000B I401 I501 I601 I703 I801 IL701 JP01 L801 M491 P401 P501 PWC1 PWC2 Q402 00001 0000A 0000B R801 RLY1 RS801 SCT1

PART CODE
48B5748C10 PTACPWH728 48586001E2 4858213803 PTBCSHH728 4852174100 4857817611 PTPKCPH728 6520010100 4858070100 485819C100 4858215701 58G0000169 48519A7310 PTCACAH728 2TF01612CL PTRTPWH394 58D0000082 2224050029 4850PM00148A96R00448A96314C2 4856017302 4856215402 7172401412 4855415800 4856017306 4856812001 PTFMSJH728 4852091400 4854870500 4856716000 PTSPPWH407 4850703S50 4858314010 PTMPMSH728 CMYH3C722H CL1UC3104M CEYD2D221D PTE2SW7100 1LA78040 4857027100 7174300811 1S7805P1C1DW7695YA1 1LA4224E 124LC04B 1STRW67351KRT30 4859109950 5PLF24A1 4854962400 4859240020 4850708N11 48599BL001 4859289320 PTF2SW7201 TTT21404857027201 7174300811 RX05B229JQ 5SC0101335 DSVC471D14 4859303930

PART NAME
TRANSMITTER REMOCON ACCESSORY AS MANUAL INSTRUCTION BAG INSTRUCTION COVER BACK AS COVER BACK CLOTH BLACK PACKING AS STAPLE PIN BOX CARTON PAD BAG P.E COIL DEGAUSSING CRT GROUND NET CABINET AS TAPE FILAMENT CRT AS COIL DY BOND SILICON PCM RUBBER WEDGE CRT BARE SCREW CRT FIX WASHER RUBBER SCREW TAPPTITE SPEC PLATE SCREW CRT FIX TIE CABLE MASK FRONT AS MASK FRONT BUTTON POWER SPRING SPEAKER AS CONNECTOR SPEAKER PCB MAIN MANUAL AS C MYLAR C LINE ACROSS C ELECTRO HEAT SINK ASSY IC VERTICAL HEAT SINK SCREW TAPPTITE IC REGULATOR IC MICOM IC SOUND AMP IC MEMORY IC POWER IC PREAMP JACK PIN BOARD FILTER LINE BUTTON CH CONN WAFER CONNECTOR CORD POWER AS CONN WAFER HEAT SINK ASS`Y TR HEAT SINK SCREW TAPPTITE R CEMENT SW RELAY VARISTOR SOCKET CRT

DESCRIPTION
R-48C10 (AAA) DTQ-14Z5SC DTQ-20V1FS L.D.P.E TO.05X250X400(+20) DTQ-14Z5SC FR HIPS BK 14Z5 FELT 200X20X0.7 DTQ-14Z5SC AUTO W65 SW-2 14Z5 EPS 14Z5 PE FOAM t0.5x1050x950 DC-1400 AL 1403S-1015-1P DTQ-14Z5SC 0.15X12mmX55mm NTSC 14 ITC CRT AS ODY-M1489 LDC7091 CARTRIDGE NY-225 (MINI NECK) HMR 28 SR (/0X54) A34AGT13X 5X25 L80 BK CR T2.0 TT2 TRS 4X14 MFZN BK 150ART P/E FILM (C/TV) 5X25 L140 YL NYLON66 DA100 DTQ-14Z5SC FR HIPS GY 14Z5 FR ABS GY 14Z5 SWPA PIE0.5 DTQ-14J4FC YH025-03+35098+ULW=200 SP-5070F01 3W 8 OHM DTQ-14Z5SC 1.6KV BUP 7200PF H WORLD AC250V 0.1UF M R.47 200V FHS 220MF (22*25) 1LA78040 + 7174300811 LA78040 SPCC T1.0+SN TT2 RND 3X8 MFZN S7805PIC 5.0V 1.0A TO-220F-3SL S/LEAD DW76950B-YA1 LA4224-E 24LC04B STR-W6735 KRT30 PH-JB-9710A LF-24A1 FR ABS GY 14Z5 YFW500-05 BIC-08T-25T+C-20T+ULW=300 USA KKP-10W+YH396-43V=2.0M YW396-43V TTT2140- + 7174300811 TT2140 AL T1.0 TT2 RND 3X8 MFZN 5W 2.2 OHM J BEN 25MM 4P DY2-5 SVC471D14A (BULK) ISMG03S INCHANG

REMARK

LOC
SF101 T401 T402 T801 U102 X701 ZZ200 CC104 CC152 CC185 CC538 CC544 CC545 CC548 CC551 CC573 CC578 CC594 CC595 CC596 CC725 CC730 CC731 CC741 CC902 CC903 CC904 I805 RC131 RC151 RC229 RC500 RC501 RC511 RC512 RC514 RC516 RC517 RC538 RC539 RC543 RC549 RC550 RC551 RC571 RC572 RC573 RC574 RC575 RC577 RC578 RC590 RC595 RC596 RC620 RC621 RC629 RC630 RC660 RC721 RC722 RC723 RC724 RC727 RC728 RC729 RC730

PART CODE
5PTSF5241P 50D10A350H0000292 50M2828B34859728630 5XYR03276C PTMPJ2H728 HCBK102KBA HCBK103KBA HCBK103KBA HCQK181JBA HCQK160JBA HCBK473KBA HCBK103KBA HCBK104KBA HCBK223KBA HCQK560JBA HCBK103KBA HCBK102KBA HCBK223KBA HCBK103KBA HCQK180JBA HCQK180JBA HCBK103KBA HCQK271JBA HCQK151JBA HCQK271JBA 1LTV817C-Q HRFT153JBA HRFT104JBA HRFT750JBA HRFT000-BA HRFT123JBA HRFT205JBA HRFT514JBA HRFT221JBA HRFT332JBA HRFT472FBA HRFT103JBA HRFT152JBA HRFT103JBA HRFT152JBA HRFT243JBA HRFT243JBA HRFT105JBA HRFT473JBA HRFT473JBA HRFT681JBA HRFT391JBA HRFT391JBA HRFT361JBA HRFT101JBA HRFT302JBA HRFT123JBA HRFT622JBA HRFT182JBA HRFT102JBA HRFT104JBA HRFT103JBA HRFT471JBA HRFT471JBA HRFT472JBA HRFT472JBA HRFT471JBA HRFT471JBA HRFT472JBA HRFT102JBA

PART NAME
FILTER SAW TRANS DRIVE FBT TRANS SMPS TUNER VARACTOR CRYSTAL QUARTZ PCB MAIN CHIP MOUNT B AS C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA C CHIP CERA IC CHIP PHOTO COUPLER R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP

DESCRIPTION
TSF5241P TD-10A3 LTC-529 TSM-2828B3 115-B-9A15AU C-001R 32.768000KHZ 20PPM DTQ-14Z5SC 50V X7R 1000PF K 1608 50V X7R 0.01MF K 1608 50V X7R 0.01MF K 1608 50V CH 180PF J 1608 50V CH 16PF J 1608 50V X7R 0.047MF K 1608 50V X7R 0.01MF K 1608 50V X7R 0.1MF K 1608 50V X7R 0.022MF K 1608 50V CH 56PF J 1608 50V X7R 0.01MF K 1608 50V X7R 1000PF K 1608 50V X7R 0.022MF K 1608 50V X7R 0.01MF K 1608 50V CH 18PF J 1608 50V CH 18PF J 1608 50V X7R 0.01MF K 1608 50V CH 270PF J 1608 50V CH 150PF J 1608 50V CH 270PF J 1608 LTV-817C TRAY 1/10 15K OHM J 1608 1/10 100K OHM J 1608 1/10 75 OHM J 1608 1/10 0 OHM 1608 1/10 12K OHM J 1608 1/10 2M OHM J 1608 1/10 510K OHM J 1608 1/10 220 OHM J 1608 1/10 3.3K OHM J 1608 1/10 4.7K OHM F 1608 1/10 10K OHM J 1608 1/10 1.5K OHM J 1608 1/10 10K OHM J 1608 1/10 1.5K OHM J 1608 1/10 24K OHM J 1608 1/10 24K OHM J 1608 1/10 1M OHM J 1608 1/10 47K OHM J 1608 1/10 47K OHM J 1608 1/10 680 OHM J 1608 1/10 390 OHM J 1608 1/10 390 OHM J 1608 1/10 360 OHM J 1608 1/10 100 OHM J 1608 1/10 3K OHM J 1608 1/10 12K OHM J 1608 1/10 6.2K OHM J 1608 1/10 1.8K OHM J 1608 1/10 1K OHM J 1608 1/10 100K OHM J 1608 1/10 10K OHM J 1608 1/10 470 OHM J 1608 1/10 470 OHM J 1608 1/10 4.7K OHM J 1608 1/10 4.7K OHM J 1608 1/10 470 OHM J 1608 1/10 470 OHM J 1608 1/10 4.7K OHM J 1608 1/10 1K OHM J 1608

REMARK

19

ELECTRICAL PARTS LIST

LOC
RC731 RC732 RC733 RC734 RC735 RC736 RC737 RC741 RC917 RC918 RC919 RC977 ZZ200 C310 C406 C410 C414 C415 C522 C574 C742 C809 C813 C814 C817 C820 C833 C881 C882 C912 R881 ZZ200 E010 E011 E012 E013 E014 E015 E016 E017 E018 E019 E021 E04 E05 E06 E07 E08 E09 P601 P801A P801B R601 R805 R814 R815 ZZ200 C101 C102 C103 C301 C303 C305 C307 C308 C311 C401

PART CODE
HRFT122JBA HRFT152JBA HRFT222JBA HRFT512JBA HRFT104JBA HRFT101JBA HRFT105JBA HRFT514JBA HRFT221JBA HRFT241JBA HRFT241JBA HRFT201JBA PTMPJ0H728 CEXF1E102V CMXF2E434J CEXF2E100V CEXF1V471V CEXF1C102V CEXF1C471V CEXF1C471V CEXF1C102V CBXB3D102K CBXB3D471K CEXF2C101V CEXF1C222V CEXF2C470V CEXF1C471V CH1BEE472M CH1BEE472M CH1BEE472M DDT7R0M140 PTMPJBH728 4856310300 4856310600 4856310600 4856310600 4856310300 4856310300 4856310300 4856310600 4856310600 4856310600 4856310300 4856310300 4856310300 4856310300 4856310300 4856310600 4856310300 485923162S 4857417500 4857417500 RF01Z688KRS02Z338JS RS02Z159JS RS02Z159JS PTMPJRH728 CEXF1H100V CEXF1C101V CEXF1H339V CMXM2A103J CEXF1H100V CEXF1H101V CXSL2H100D CMXM2A104J CEXD1H229Q CCXB2H102K

PART NAME
R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP PCB MAIN (RHU) AS C ELECTRO C MYLAR C ELECTRO C ELECTRO C ELECTRO C ELECTRO C ELECTRO C ELECTRO C CERA SEMI C CERA SEMI C ELECTRO C ELECTRO C ELECTRO C ELECTRO C CERA AC C CERA AC C CERA AC POSISTOR PCB MAIN M-10 AS EYE LET EYE LET EYE LET EYE LET EYE LET EYE LET EYE LET EYE LET EYE LET EYE LET EYE LET EYE LET EYE LET EYE LET EYE LET EYE LET EYE LET CONN WAFER TERM PIN TERM PIN R FUSIBLE R M-OXIDE FILM R M-OXIDE FILM R M-OXIDE FILM PCB MAIN RADIAL AS C ELECTRO C ELECTRO C ELECTRO C MYLAR C ELECTRO C ELECTRO C CERA C MYLAR C ELECTRO C CERA

DESCRIPTION
1/10 1.2K OHM J 1608 1/10 1.5K OHM J 1608 1/10 2.2K OHM J 1608 1/10 5.1K OHM J 1608 1/10 100K OHM J 1608 1/10 100 OHM J 1608 1/10 1M OHM J 1608 1/10 510K OHM J 1608 1/10 220 OHM J 1608 1/10 240 OHM J 1608 1/10 240 OHM J 1608 1/10 200 OHM J 1608 DTQ-14Z5SC 25V RSS 1000MF (13X20) TP 250V MPP 0.43MF J (TP) 250V RSS 10MF (10X20) TP 35V RSS 470MF (10X20) TP 16V RSS 1000MF (10X20) TP 16V RSS 470MF (8X12)TP 16V RSS 470MF (8X12)TP 16V RSS 1000MF (10X20) TP 2KV BL(N) 1000PF K (T) 2KV BL(N) 470PF K (T) 160V RSS 100MF (16X25) TP 16V RSS 2200MF (13X25) TP 160V RSS 47MF (13X25) TP 16V RSS 470MF (8X12)TP U/C/V 2.5KV 4700PF TP U/C/V 2.5KV 4700PF TP U/C/V 2.5KV 4700PF TP ECPAC7R0M140 DTQ-14Z5SC BSR T0.2 (R1.6) BSR T0.2 (R2.3) BSR T0.2 (R2.3) BSR T0.2 (R2.3) BSR T0.2 (R1.6) BSR T0.2 (R1.6) BSR T0.2 (R1.6) BSR T0.2 (R2.3) BSR T0.2 (R2.3) BSR T0.2 (R2.3) BSR T0.2 (R1.6) BSR T0.2 (R1.6) BSR T0.2 (R1.6) BSR T0.2 (R1.6) BSR T0.2 (R1.6) BSR T0.2 (R2.3) BSR T0.2 (R1.6) YW025-03 (STICK) DA-IB0214(D2.3/DY PIN) DA-IB0214(D2.3/DY PIN) 1W 0.68 OHM K (TAPPING) 2W 0.33 OHM J SMALL 2W 1.5 OHM J SMALL 2W 1.5 OHM J SMALL DTQ-14Z5SC 50V RSS 10MF (5X11) TP 16V RSS 100MF (6.3X11) TP 50V RSS 3.3MF (5X11) TP 100V 0.01MF J (TP) 50V RSS 10MF (5X11) TP 50V RSS 100MF (8X11.5) TP 500V SL 10PF D (TAPPING) 100V 0.1MF J (TP) 50V RT 2.2MF (6.3X11) TP 500V B 1000PF K (TAPPING)

REMARK

LOC
C403 C405 C411 C412 C413 C416 C418 C450 C451 C452 C509 C510 C513 C514 C515 C516 C517 C543 C546 C547 C550 C571 C576 C582 C590 C597 C598 C599 C601 C604 C620 C623 C630 C634 C701 C735 C736 C737 C810 C811 C815 C830 C831 C848 C890 C893 F801 I803 L805 L901 Q401 Q404 Q450 Q510 Q575 Q805 Q806 Q835 Q845 Q848 Q902 Q903 Q904 Q977 R301 R302 R303

PART CODE
CMXM2A103J CEXF2C109V CEXF1H100V CCXB2H102K CCXB2H102K CCXB2H102K CMXM2A104J CEXF1C100V CEXF1C101V CEXF1C221C CMXM2A102J CMXL1J334J CMXM2A153J CMXL1J474J CMXM2A153J CEXF1H109V CEXF1C101V CEXF1H470V CEXF1H478V CEXF1H470V CMXM2A473J CEXF1H109V CEXF1C101V CEXF1H109V CEXD1H109F CXCH1H809D CEXF1H109V CMXM2A103J CEXF1C331V CEXF1H470V CMXM2A153J CEXF1H109V CEXF1C221V CEXF1H100V CEXF1C101V CEXF1H338V CEXF1H229V CMXM2A333J CCXB2H222K CCXB2H222K CEXF2A100V CMXL2E104K CMXM2A103J CEXF1C101V CEXF1H100V CEXF1H479V 5FWPS4022L 1K1A431B 58CX430599 5CPX121J TKTC3207 TKTC3198YTKTC3198YTKTA1266YTKTA1275YTKTC3205YTKTA1275YTKTC3198YTKTC3198YTKTC3198YTKTC3207 TKTC3207 TKTC3207 TKTA1266YRN02B471JS RN02B681JS RN02B129JS

PART NAME
C MYLAR C ELECTRO C ELECTRO C CERA C CERA C CERA C MYLAR C ELECTRO C ELECTRO C ELECTRO C MYLAR C MYLAR C MYLAR C MYLAR C MYLAR C ELECTRO C ELECTRO C ELECTRO C ELECTRO C ELECTRO C MYLAR C ELECTRO C ELECTRO C ELECTRO C ELECTRO C CERA C ELECTRO C MYLAR C ELECTRO C ELECTRO C MYLAR C ELECTRO C ELECTRO C ELECTRO C ELECTRO C ELECTRO C ELECTRO C MYLAR C CERA C CERA C ELECTRO C MYLAR C MYLAR C ELECTRO C ELECTRO C ELECTRO FUSE IC REGULATOR(SHUNT) COIL CHOKE COIL PEAKING TR TR TR TR TR TR TR TR TR TR TR TR TR TR R METAL FILM R METAL FILM R METAL FILM

DESCRIPTION
100V 0.01MF J (TP) 160V RSS 1MF (6.3X11) TP 50V RSS 10MF (5X11) TP 500V B 1000PF K (TAPPING) 500V B 1000PF K (TAPPING) 500V B 1000PF K (TAPPING) 100V 0.1MF J (TP) RSS 16V 10MF 4X7 16V RSS 100MF (6.3X11) TP 16V RUS 220MF (8X11.5) TP 100V 1000PF J (TP) 63V MEU 0.33MF J (TP) 100V 0.015MF J (TP) 63V MEU 0.47MF J 100V 0.015MF J (TP) 50V RSS 1MF (5X11) TP 16V RSS 100MF (6.3X11) TP 50V RSS 47MF (6.3X11) TP 50V RSS 0.47MF (5X11) TP 50V RSS 47MF (6.3X11) TP 100V 0.047MF J (TP) 50V RSS 1MF (5X11) TP 16V RSS 100MF (6.3X11) TP 50V RSS 1MF (5X11) TP 50V RND 1MF (5X11) TP 50V CH 8PF D (TAPPING) 50V RSS 1MF (5X11) TP 100V 0.01MF J (TP) 16V RSS 330MF (8X11.5) TP 50V RSS 47MF (6.3X11) TP 100V 0.015MF J (TP) 50V RSS 1MF (5X11) TP 16V RSS 220MF (8X11.5) TP 50V RSS 10MF (5X11) TP 16V RSS 100MF (6.3X11) TP 50V RSS 0.33MF (5X11) TP 50V RSS 2.2MF (5X11) TP 100V 0.033MF J (TP) 500V B 2200PF K (TAPPING) 500V B 2200PF K (TAPPING) 100V RSS 10MF (6.3X11) TP 250V MEU 0.1MF K 100V 0.01MF J (TP) 16V RSS 100MF (6.3X11) TP 50V RSS 10MF (5X11) TP 50V RSS 4.7MF (5X11) TP WIDE TL 250V 4A CASE KIA431B 2.495V 0.5% TO-92 AZ-9004Y 940K TP 120UH J (RADIAL) KTC3207 (TP) KTC3198Y KTC3198Y KTA1266Y (TP) KTA1275Y (TP) KTC3205Y (TP) KTA1275Y (TP) KTC3198Y KTC3198Y KTC3198Y KTC3207 (TP) KTC3207 (TP) KTC3207 (TP) KTA1266Y (TP) 2W 470 OHM J SMALL 2W 680 OHM J SMALL 2W 1.2 OHM J SMALL

REMARK

20

ELECTRICAL PARTS LIST

LOC
R305 R406 R409 R411 R412 R413 R414 R415 R419 R420 R893 R913 R914 R915 SW701 SW702 SW703 SW704 SW705 SW706 X503 Z501 ZZ200 A001 C109 C511 C518 C523 C602 C891 C892 C894 D101 D102 D104 D301 D311 D312 D405 D406 D407 D408 D409 D415 D503 D504 D571 D572 D573 D574 D804 D807 D808 D809 D811 D812 D813 D817 D835 D881 D882 D883 D884 J1 J10 J11 J13 J15

PART CODE
RN01B331JS RN01B562JS RN02B560JS RN02B150JS RN01B109JS RN01B109JS RN01B229JS RN02B279JS RN02B100JS RN02B620JS RN01B331JS RN02B153JS RN02B153JS RN02B153JS 5S50101090 5S50101Z90 5S50101Z90 5S50101Z90 5S50101Z90 5S50101Z90 5XEX3R579C 5PXXT4R5MB PTMPJAH728 4859819891 CCZF1H103Z CCZB1H222K CCZB1H102K CBZF1H104Z CBZF1H104Z CCZB1H821K CCZB1H471K CCZB1H333K DUZ33B DUZ5R1BDMTZJ5R6BD1N4004S DBZX55C6285801060GY D1N4937G D1N4937G D1N4937G D1N4937G D1N4148D1N4937G DUZ9R1BM D1N4148D1N4148D1N4148D1N4148D1N4148D1N4937G DRGP15JD1N4937G DMTZJ6R2CD1N4937G D1N4148D1N4937G DMTZJ5R6BDMTZJ6R8CDLT2A05G DLT2A05G DLT2A05G DLT2A05G 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY

PART NAME
R METAL FILM R METAL FILM R METAL FILM R METAL FILM R METAL FILM R METAL FILM R METAL FILM R METAL FILM R METAL FILM R METAL FILM R METAL FILM R METAL FILM R METAL FILM R METAL FILM SW TACT SW TACT SW TACT SW TACT SW TACT SW TACT CRYSTAL QUARTZ FILTER CERA PCB MAIN AXIAL AS PCB MAIN C CERA C CERA C CERA C CERA SEMI C CERA SEMI C CERA C CERA C CERA DIODE ZENER DIODE ZENER DIODE ZENER DIODE DIODE ZENER WIRE COPPER DIODE DIODE DIODE DIODE DIODE DIODE DIODE ZENER DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE ZENER DIODE DIODE DIODE DIODE ZENER DIODE ZENER DIODE DIODE DIODE DIODE WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER

DESCRIPTION
1W 330 OHM J SMALL 1W 5.6K OHM J SMALL 2W 56 OHM J SMALL 2W 15 OHM J SMALL 1W 1 OHM J SMALL 1W 1 OHM J SMALL 1W 2.2 OHM J SMALL 2W 2.7 OHM J SMALL 2W 10 OHM J SMALL 2W 62 OHM J SMALL 1W 330 OHM J SMALL 2W 15K OHM J SMALL 2W 15K OHM J SMALL 2W 15K OHM J SMALL THVH472GCA THVV502GDA THVV502GDA THVV502GDA THVV502GDA THVV502GDA HC-49/U 3.579545M (TP) XT 4.5MB-TP DTQ-14Z5SC 197X246 S1B 50V F 0.01MF Z 50V B 2200PF K AXIAL 50V B 1000PF K (AXIAL) 50V F 0.1MF Z 50V F 0.1MF Z 50V B 820PF K AXIAL 50V B 470PF K (AXIAL) 50V B 0.033MF K AXL UZ-33B UZ-5.1B MTZJ 5.6B 1N4004S BZX55C-62 1/0.6 TIN COATING 1N4937G (TAPPING) 1N4937G (TAPPING) 1N4937G (TAPPING) 1N4937G (TAPPING) 1N4148 (TAPPING) 1N4937G (TAPPING) UZ-9.1BM 1N4148 (TAPPING) 1N4148 (TAPPING) 1N4148 (TAPPING) 1N4148 (TAPPING) 1N4148 (TAPPING) 1N4937G (TAPPING) RGP15J DO-204AC 600V 1.5A 1N4937G (TAPPING) MTZJ 6.2C 1N4937G (TAPPING) 1N4148 (TAPPING) 1N4937G (TAPPING) MTZJ 5.6B MTZJ 6.8C LT2A05G (TP) LT2A05G (TP) LT2A05G (TP) LT2A05G (TP) 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING

REMARK

LOC
J16 J17 J18 J19 J20 J21 J22 J23 J24 J25 J26 J27 J28 J29 J3 J30 J31 J32 J34 J35 J36 J37 J38 J39 J4 J40 J41 J42 J43 J44 J45 J46 J47 J48 J49 J50 J51 J52 J53 J54 J55 J56 J57 J58 J59 J6 J60 J7 J8 L111 L501 L503 L504 L515 L578 L701 L806 L807 L811 R104 R150 R306 R307 R308 R309 R311 R352 R353

PART CODE
85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 5CPZ220K02 5CPZ100K02 5CPZ569K02 5CPZ220K02 5CPZ270K02 5CPZ100K04 5MC0000100 5MC0000100 5MC0000100 RD-AZ103JRD-AZ472JRD-AZ273JRD-AZ303JRD-AZ222JRD-AZ113JRD-AZ752JRN-4Z1603F RN-4Z1502F

PART NAME
WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER COIL PEAKING COIL PEAKING COIL PEAKING COIL PEAKING COIL PEAKING COIL PEAKING COIL BEAD COIL BEAD COIL BEAD R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R METAL FILM R METAL FILM

DESCRIPTION
1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 1/0.6 TIN COATING 22UH K (AXIAL 3.5MM) 10UH K (AXIAL 3.5MM) 5.6UH K (AXIAL 3.5MM) 22UH K (AXIAL 3.5MM) 27UH K (AXIAL 3.5MM) 10UH 10.5MM K (LAL04TB) HC-3550 HC-3550 HC-3550 1/6 10K OHM J 1/6 4.7K OHM J 1/6 27K OHM J 1/6 30K OHM J 1/6 2.2K OHM J 1/6 11K OHM J 1/6 7.5K OHM J 1/4 160K OHM F 1/4 15K OHM F

REMARK

21

ELECTRICAL PARTS LIST

LOC
R401 R405 R416 R417 R423 R424 R450 R451 R452 R502 R509 R513 R531 R532 R533 R534 R544 R554 R576 R640 R701 R706 R725 R789 R790 R809 R818 R819 R820 R824 R825 R826 R831 R832 R835 R836 R841 R842 R845 R846 R848 R872 R888 R890 R892 R894 R901 R910 R911 R912 R923 R924 R925 R933 R934 R935 R978 R979

PART CODE
RD-4Z472JRD-2Z152JRD-2Z121JRD-4Z302JRD-AZ102JRD-AZ331JRD-AZ333JRN-4Z1502F RN-4Z1002F RD-2Z151JRD-AZ334JRD-4Z822JRD-AZ331JRD-AZ331JRD-AZ331JRD-2Z820JRD-AZ222JRD-4Z102JRD-4Z475JRD-2Z241JRD-4Z479JRD-AZ102JRD-AZ101JRD-AZ102JRD-AZ102JRD-4Z823JRD-AZ103JRD-4Z561JRD-4Z392JRD-AZ562J85801060GY RD-AZ563JRD-AZ332JRN-4Z2201F RD-AZ101JRD-AZ473JRN-4Z1003F RN-4Z1502F RD-AZ103JRD-AZ472JRD-AZ103JRD-AZ102JRC-2Z565KP RD-4Z102JRD-4Z152JRD-4Z240JRD-4Z474JRD-2Z332JRD-2Z332JRD-2Z332JRD-AZ101JRD-AZ101JRD-AZ101JRD-AZ101JRD-AZ101JRD-AZ101JRD-AZ102JRD-AZ272J-

PART NAME
R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R METAL FILM R METAL FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM WIRE COPPER R CARBON FILM R CARBON FILM R METAL FILM R CARBON FILM R CARBON FILM R METAL FILM R METAL FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON COMP R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM R CARBON FILM

DESCRIPTION
1/4 4.7K OHM J 1/2 1.5K OHM J 1/2 120 OHM J 1/4 3K OHM J 1/6 1K OHM J 1/6 330 OHM J 1/6 33K OHM J 1/4 15K OHM F 1/4 10K OHM F 1/2 150 OHM J 1/6 330K OHM J 1/4 8.2K OHM J 1/6 330 OHM J 1/6 330 OHM J 1/6 330 OHM J 1/2 82 OHM J 1/6 2.2K OHM J 1/4 1K OHM J 1/4 4.7M OHM J 1/2 240 OHM J 1/4 4.7 OHM J 1/6 1K OHM J 1/6 100 OHM J 1/6 1K OHM J 1/6 1K OHM J 1/4 82K OHM J 1/6 10K OHM J 1/4 560 OHM J 1/4 3.9K OHM J 1/6 5.6K OHM J 1/0.6 TIN COATING 1/6 56K OHM J 1/6 3.3K OHM J 1/4 2.20K OHM F 1/6 100 OHM J 1/6 47K OHM J 1/4 100K OHM F 1/4 15K OHM F 1/6 10K OHM J 1/6 4.7K OHM J 1/6 10K OHM J 1/6 1K OHM J 1/2 5.6M OHM K 1/4 1K OHM J 1/4 1.5K OHM J 1/4 24 OHM J 1/4 470K OHM J 1/2 3.3K OHM J 1/2 3.3K OHM J 1/2 3.3K OHM J 1/6 100 OHM J 1/6 100 OHM J 1/6 100 OHM J 1/6 100 OHM J 1/6 100 OHM J 1/6 100 OHM J 1/6 1K OHM J 1/6 2.7K OHM J

REMARK

22

WAVEFORMS
(1) I501 PIN 12 (2) I501 PIN 13

V:1V/div H:25us/div

V:1V/div H:25us/div

(3) I501 PIN 14

(4) I501 PIN 17

V:1V/div H:25us/div

V:500mV/div H:5ms/div

(5) I501 PIN 56

(6) I501 PIN 60

V:500mV/div H:25us/div

V:500mV/div H:25us/div

(7) I501 PIN 63

(8) I501 PIN 53

V:10V/div H:5ms/div

V:2V/div H:25us/div

23

WAVEFORMS
(9) I801 PIN 7

V:100V/div H:10us/div

(10) T402 PIN 25.5V

(11) T402 PIN 10.5V

V:100V/div H:25us/div

V:50V/div H:25us/div

(12) T402 PIN HEATER

(13) T402 PIN 180V

V:10V/div H:25us/div

V:100V/div H:25us/div

24

WAVEFORMS
(14) T401 PIN H.V (15) T801 PIN 133V

V:100V/div H:25us/div

V:100V/div H:10us/div

(16) Q401 COLLECTOR

(17) CRT SOCKET PIN B

V:5V/div H:25us/div

V:50V/div H:25us/div

(18) CRT SOCKET PIN R

(19) CRT SOCKET PIN G

V:50V/div H:25us/div

V:50V/div H:25us/div

25

Appendix

IC DESCRIPTION

I. MICOM Outline. 1. Abstract.

This specification is 1-Tunner Mono Model for North America, CCD 1-Chip MICOM It is developing software specification for tuning only NTSC system TV F/S. LA76950B

2. H/W Outline.
1) ROM : 32K x 8bits.tsc 2) RAM : 1152 x 8bits. 3) OSD Function. . Screen Display. :32 characters x 2 lines. . Characters. 254 patterns programmable. . Character display area CC mode : 16 x 26 dots . Chatacter color : 8 colors . Attribute CC mode : smooth italic, underline, flash, automatic solid space OSD mode : border . Display position Horizontal : 128 levels Vertical : 512 levels

3. System Feature.
. . . . . The system for TV tuning is Frequency Synthesis type. Closed Caption s function is built in IC. On Screen Display s function is built in IC. Package. : 64 PIN DIP. 2 Tuner (Pre-scaler.) : I C Bus. --- 115-B-B9015AU Remote. : R-48C04 Series 2 2 : 24C04(I C Bus) a Apply one byte Read/Write mode. E PROM. 6-Local Key. : A/D Input Control.(Power, Ch Up/Down, Vol Up/Down, Menu) Option S/W : Port Input Option Check. IF/V/C/D IC : LA76950B (America, The only NTSC)

.
. . . .

4. Function.
1) C. C. D. function. . A section of C. C. D. operates FCC based specification. 2) C. C. D. controlled function. . Closed Caption Mode. (Off<-->C1<-->C2<-->T1<-->T2<-->Off) . CC On Mute.(Off / On) . When CC On Mute is On, Output is selected a item of Closed Caption Modes. 3) Tuning Function. . I 2C Bus. . PLL IC Interface. . FS 181 Channel (AIR 2-69CH, CABLE 1-125CH) . AFT Operation(Fine Tuning ) -2.5 Fn+2.5MHz . AIR/CABLE (STD, HRC, IRC ). Only Cable 5,6CH is that AFT range is cover over broad-band. -2.5MHz Fn+3.5MHz. . Auto Program.(If a channel is broadcasting, the channel is memorized.) . Direct Tuning(0 9KEY) . Channel Up/Down.(Memorized Channels) -> The Ch Up/Down buttons on the Remote and

26

Appendix

IC DESCRIPTION

on the front panel are same function. . Search Channel Up/Down.(If No-Memory or only 1CH is Memory) . Channel Memory.(ADD/DELETE) . Channel Review Function. . Last Channel Memory Function. 4) OSD Function. . In Video Mode, Things(Items) that is concerned with Air and Cable disappear in the Menu. . Channel, AV display. 2 . Volume , Picture Control --> I C Bus Control 5) The Others Function. . Video/Audio Mute Function. . If a Channel is no signal, it is Auto-Power Off Function after 15 minutes. . Heat Run Function. --- OSD White Background. . Sleep Timer , Wake-Up Time, Off Time Function. . Audio Mode :Mono . TV/Line Controlled function. ----------------------- (Option) . Prison Controlled function. ----------------------- (Option) . 3-Language.(North America : ENG/SPA/FRA ). 2 2 . E PROM Interface (I C Bus Control) . CH 6 TRAP Function.(IS-31 ) . PLL IC Band Data.(Control Byte 2-->P3~P0) VHF L : 1 / VHF H : 2 / CH6 TRAP : 5 (IS-31) AIR(Cable) CH 6 Only UHF : 8

5.The Table of Option and Schedule(SOFT OPTION)

N0 1 2 3 OPTION
NO SD BLUE BACK

FUCTION NO SIGNAL : BLUE BACK NO SIGNAL : NOISE Video Model No Video Model Normal Model Clock Menu(TIME) `

TV ONLY PRISON

Remarks SVC REMOCON S11 KEY NO SD BLUE BACK : ON NO SD BLUE BACK : OFF TV ONLY OPTION : OFF TV ONLY OPTION : ON PRISON OPTION : OFF PRISON OPTION : ON

6. KEY Matrix
MICOM #36(KEY IN) 5V

1 2 3 4 5 6

Key SW701 SW705 SW704 SW703 SW702 SW706

Function POWER VOL + VOL CH + CH MENU

VALUE(V) 0~0.55 0.87~1.19 1.59~1.9 2.2~2.5 2.79~3.1 3.52~3.9

27

Appendix

IC DESCRIPTION

II. PIN ASSIGN

PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 FUNCTION SIF Output PIF AGC SIF Input FM FILTER FM Output AUDIO Ooutput SIF APC Filter IF Vcc EXT. AUDIO Input ABL RGB Vcc Red Output Green Output Blue Output NC V. Ramp Osc. Capacitor Vertical Output VCO IREF Horizontal/Bus Vcc Horizontal AFC Filter Horzontal Output Video/Vertical/BUS Ground NC NC NC Remocon Input Sound Mute D/G Relay ST-BY LED Power IIC DATA IIC CLOCK PIN 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 FUNCTION PIF Input1 PIF Input2 IF Ground RF AGC Output Video Output AFT Filter APC Filter Black Level Det.Filter Internal Video Input Video / Vertical Vcc External Video Input Chroma APC Filter NC NC 3.58MHz Crystal NC NC X-RAY NC NC Flyback Pulse Input NC CPU Ground PLL Reset Filter NC GND AGC Input Key Input VDD XT2 XT1

"H" Active

28

Appendix

TROUBLESHOOTING GUIDE

1. NO POWER

29

I501

#6

SDA SCL

#31 #8

#32

#63

#64 #1 #3

I501
Check ATT FILTER Circut

#6

#4

5
Auto out

#2 #1 I601 LA4224 #3 C630

C623
#7

#5

Sound Mute

31

4. NO COLOR

#56

#55 VI/VE Vcc

#50

X503

I501
#12 #13 #14

5.NO VERTICAL DEFLECTION

#35 VDD Vertical IC Vcc (25V)

Check the voltage (25V)

I501
#50 X503

#6

LA78040
#17 #1 #5

32

6. REMOTE CONTROL DOES NOT OPERATE

#26

I501

#35

Check the voltage

VDD 5V

33

DAEWOO ELECTRONICS CORP.

686, AHYEON-DONG, MAPO-GU, SEOUL, KOREA. C.P.O. BOX 8003 SEOUL KOREA

PRINTED DATE : AUG. 2005