Manual Service MT1389se

SERVICE MANUAL MODEL
DVP-767
CAUTION : Before servicing this chassis, read the "PRODUCT SAFETY SERVICE FOR VIDEO PRODUCTS" section
on page 2 of this manual.
DVD and CD CONTENTS
PLAYER SERVICE PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . 2,3

BLOCK DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ELECTRICAL TROUBLE SHOOTING GUIDE. . . . . . . . . . 5,15
PRINTED CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16,21
REPLACEMENT PARTS LIST . . . . . . . . . . . . . . . . . . . . . . 22,28
PRODUCT SAFETY SERVICING GUIDELINES FOR VIDEO PRODUCTS
CAUTION: DO NOT ATTEMPT TO MODIFY THIS PRODUCT IN ANY WAY AND SUBJECT: X-RADIATION
N E V E R P E R F O R M C U S T O M I Z E D I N S T A L L AT I O N S W I T H O U T
MANUFACTURER'S APPROVAL. UNAUTHORIZED MODIFICATIONS WILL NOT 1. BE SURE PROCEDURES AND INSTRUCTIONS TO ALL SERVICE PERSONNEL
ONLY VOID THE WARRANTY, BUT MAY LEAD TO YOUR BEING LIABLE FOR COVER THE SUBJECT OF X-RADIATION. THE ONLY POTENTIAL SOURCE OF
ANY RESULTING PROPERTY DAMAGE OR USER INJURY. X-RAYS IN CURRENT T.V. RECEIVERS IS THE PICTURE TUBE. HOWEVER,
THIS TUBE DOES NOT EMIT X-RYS WHEN THE HIGH VOLTAGE IS AT THE
SERVICE WORK SHOULD BE PERFORMED ONLY AFTER YOU ARE FACTORY SPECIFIED LEVEL. THE PROPER VALUE IS GIVEN IN THE
THOROUGHLY FAMILIAR WITH ALL OF THE FOLLOWING SAFETY CHECKS APPLICABLE SCHEMATIC. OPERATION AT HIGHER VOLTAGES MAY CAUSE A
AND SERVICING GUIDELINES. TO DO OTHERWISE, INCREASES THE RISK OF FAILURE OF THE PICTURE TUBE OR HIGH VOLTAGE SUPPLY AND, UNDER
POTENTIAL HAZARDS AND INJURY TO THE USER. CERTAIN CIRCUMSTANCES, MAY PRODUCE RADIATION IN EXCESS OF
WHILE SERVICING, USE AN ISOLATION TRANSFORMER FOR PROTECTION DESIRABLE LEVELS.
FROM A.C. LINE SHOCK. 2. ONLY FACTORY SPECIFIED C.R.T ANODE CONNECTORS MUST BE USED.
DEGAUSSING SHIELDS ALSO SERVE AS AN X-RAY SHIELD IN COLOR SETS,
SAFETY CHECKS ALWAYS RE-INSTALL THEM.
AFTER THE ORIGINAL SERVICE PROBLEM HAS BEEN CORRECTED, A CHECK 3. IT IS ESSENTIAL THAT SERVICE PERSONNEL HAVE AVAILABLE AN
SHOULD BE MADE OF THE FOLLOWING. ACCURATE AND RELIABLE HIGH VOLTAGE METER. THE CALIBRATION OF
SUBJECT: FIRE & SHOCK HAZARD THE METER SHOULD BE CHECKED PERIODICALLY AGAINST A
REFERENCE STANDARD, SUCH AS THE ONE AVAILABLE AT YOUR
1. BE SURE THAT ALL COMPONENTS ARE POSITIONED IN SUCH A WAY AS DISTRIBUTOR.
TO AVOID POSSIBILITY OF ADJACENT COMPONENT SHORTS. THIS IS
ESPECIALLY IMPORTANT ON THOSE MODULES WITCH ARE 4. WHEN THE HIGH VOLTAGE CIRCUITRY IS OPERATING PROPERLY, THERE IS
TRANSPORTED TO AND FROM THE REPAIR SHOP. NO POSSIBILITY OF AN X-RADIATION PROBLEM. EVERY TIME A COLOR
CHASSIS IS SERVICED, THE BRIGHTNESS SHOULD BE RUN UP AND DOWN
2. NEVER RELEASE A REPAIR UNLESS ALL PROTECTIVE DEVICES SUCH AS WHILE MONITORING THE HIGH VOLTAGE WITH A METER TO BE CERTAIN
INSULATORS, BARRIERS, COVERS, SHIELDS, STRAIN RELIEFS, POWER THAT THE HIGH VOLTAGE DOES NOT EXCEED THE SPECIFIED VALUE AND
SUPPLY CORDS, AND OTHER HARDWARE HAVE BEEN REINSTALLED PER THAT IT IS REGULATING CORRECTLY. WE SUGGEST THAT YOU AND YOUR
ORIGINAL DESIGN. BE SURE THAT THE SAFETY PURPOSE OF THE SERVICE ORGANIZATION REVIEW TEST PROCEDURES SO THAT VOLTAGE
POLARIZED LINE PLUG HAS NOT BEEN DEFEATED. REGULATION IS ALWAYS CHECKED AS A STANDARD SERVICING
3. SOLDERING MUST BE INSPECTED TO DISCOVER POSSIBLE COLD PROCEDURE AND THAT THE HIGH VOLTAGE READING BE RECORDED ON
SOLDER JOINTS, SOLDER SPLASHES OR SHARP SOLDER POINTS. BE EACH CUSTOMER'S INVOICE.
CERTAIN TO REMOVE ALL LOOSE FOREIGN PARTICLES. 5. WHEN TROUBLESHOOTING AND MAKING TEST MEASUREMENTS IN A
4. CHECK FOR PHYSICAL EVIDENCE DF DAMAGE OR DETERIORATION TO PRODUCT WITH A PROBLEM OF EXCESSIVE HIGH VOLTAGE AVOID BEING
PARTS AND COMPONENTS, FOR FRAYED LEADS AND DAMAGED UNNECESSARILY CLOSE TO THE PICTURE TUBE AND THE HIGH VOLTAGE
INSULATION (INCLUDING A.C. CORD), AND REPLACE IF NECESSARY SUPPLY DO NOT OPERATE THE PRODUCT LONGER THAN IT IS NECESSARY
FOLLOW ORIGINAL LAYOUT, LEAD LENGTH AND DRESS. TO LOCATE THE CAUSE OF EXCESSIVE VOLTAGE.
5. NO LEAD OR COMPONENT SHOULD TOUCH A RECEIVING TUBE OR A 6. REFER TO HV. B+ AND SHUTDOWN ADJUSTMENT PROCEDURES
RESISTOR RATED AT 1 WATT OR MORE. LEAD TENSION AROUND DESCRIBED IN THE APPROPRIATE SCHEMATIC AND DIAGRAMS(WHERE
PROTRUDING METAL SURFACES MUST BE AVOIDED. USED).
6. ALL CRITICAL COMPONENTS SUCH AS FUSES. FLAMEPROOF RESISTORS, SUBJECT: IMPLOSION

CAPACITORS, ETC. MUST BE REPLACED WITH EXACT FACTORY TYPES, 1. ALL DIRECT VIEWED PICTURE TUBES ARE EQUIPPED WITH AN INTEGRAL
DO NOT USE REPLACEMENT COMPONENTS OTHER THAN THOSE IMPLOSION PROTECTION SYSTEM, BUT CARE SHOULD BE TAKEN TO
SPECIFIED OR MAKE UNRECOMMENDED CIRCUIT MODIFICATIONS. AVOID DAMAGE DURING INSTALLATION, AVOID SCRATCHING THE TUBE. IF
7. AFTER RE-ASSEMBLY OF THE SET, ALWAYS PERFORM AN A.C. LEAKAGE SCRATCHED REPLACE IT.
TEST ON ALL EXPOSED METALLIC PARTS OF THE CABINET, (THE 2. USE ONLY RECOMMENDED FACTORY REPLACEMENT TUBES.
CHANNEL SELECTOR KNOB, ANTENNA TERMINALS. HANDLE AND
SCREWS) TO BE SURE THE SET IS SAFE TO OPERATE WITHOUT DANGER SUBJECT: TIPS ON PROPER INSTALLATION
OF ELECTRICAL SHOCK. DO NOT USE A LINE ISOLATION TRANSFORMER
DURING THIS TEST, MAKE SURE TO USE AN A.C. VOLTMETER. HAVING 1. NEVER INSTALL ANY PRODUCT IN A CLOSED-IN RECESS. CUBBYHOLE OR
5000 OHMS PER VOLT OR MORE SENSITIVITY, IN THE FOLLOWING CLOSELY FITTING SHELF SPACE, OVER OR CLOSE TO HEAT DUCT, OR IN
MANNER; CONNECT A 1500 OHMS 10 WATT RESISTOR, PARALLELED BY THE PATH OF HEATED AIR FLOW.
A.15 MFD. 150V A.C. TYPE CAPACITOR BETWEEN A KNOWN GOOD EARTH 2. AVOID CONDITIONS OF HIGH HUMIDITY SUCH AS: OUTDOOR PATIO
GROUND (WATER PIPE, CONDUIT, ETC.) AND THE EXPOSED METALLIC INSTALLATIONS WHERE DEW IS A FACTOR, NEAR STEAM RADIATORS
PARTS, ONE AT A TIME. MEASURE THE A.C. VOLTAGE ACROSS THE WHERE STEAM LEAKAGE IS A FACTOR, ETC.
COMBINATION OF 1500 OHM RESISTOR AND 15 MFD CAPACITOR.
REVERSE THE A.C. PLUG AND REPEAT A.C. ANY VOLTAGE 3. AVOID PLACEMENT WHERE DRAPERIES MAY OBSTRUCT REAR VENTING.
MEASUREMENTS FOR EACH EXPOSED METALLIC PART. VOLTAGE THE CUSTOMER SHOULD ALSO AVOID THE USE OF DECORATIVE
MEASURED MUST NOT EXCEED 75 VOLTS R.M.S. THIS CORRESPONDS SCARVES OR OTHER COVERINGS WHICH MIGHT OBSTRUCT VENTILATION.
TO 0.5 MILLIAMP A.C. ANY VALUE EXCEEDING THIS LIMIT CONSTITUTES A 4. WALL AND SHELF MOUNTED INSTALLATIONS USING A COMMERCIAL
POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED IMMEDIATELY. MOUNTING KIT, MUST FOLLOW THE FACTORY APPROVED MOUNTING
INSTRUCTIONS. A PRODUCT MOUNTED TO A SHELF OR PLATFORM MUST
RETAIN ITS ORIGINAL FEET (OR THE EQUIVALENT THICKNESS IN SPACERS)
TO PROVIDE ADEQUATE AIR FLOW ACROSS THE BOTTOM. BOLTS OR
SCREWS USED FOR FASTENERS MUST NOT TOUCH ANY PARTS OR
WIRING. PERFORM LEAKAGE TEST ON CUSTOMIZED INSTALLATIONS.
5. CAUTION CUSTOMERS AGAINST THE MOUNTING OF A PRODUCT ON
SLOPING SHELF OR A TILTED POSITION, UNLESS THE PRODUCT IS
PROPERLY SECURED.
GOOD EARTH GROUND PLACE THIS PROBE 6. A PRODUCT ON A ROLL-ABOUT CART SHOULD BE STABLE ON ITS
SUCH AS THE WATER ON EACH EXPOSED MOUNTING TO THE CART CAUTION THE CUSTOMER ON THE HAZARDS OF
PIPE, CONDUIT, ETC. METAL PART TRYING TO ROLL A CART WITH SMALL CASTERS ACROSS THRESHOLDS
OR DEEP PILE CARPETS.
7. CAUTION CUSTOMERS AGAINST THE USE OF A CART OR STAND WHICH
SUBJECT GRAPHIC SYMBOLS HAS NOT BEEN LISTED BY UNDERWRITERS LABORATORIES, INC. FOR USE
THE LIGHTNING FLASH WITH APROWHEAD SYMBOL. WITHIN AN WITH THEIR SPECIFIC MODEL OF TELEVISION RECEIVER OR
EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE SERVICE GENERICALLY APPROVED FOR USE WITH TV'S OF THE SAME OR LARGER
PERSONNEL TO THE PRESENCE OF UNINSULATED "DANGEROUS SCREEN SIZE.
VOLTAGE" THAT MAY BE OF SUFFICIENT MAGNITUDE TO 8. CAUTION CUSTOMERS AGAINST THE USE OF EXTENSION CORDS. EXPLAIN
CONSTITUTE A RISK OF ELECTRIC SHOCK. THAT A FOREST OF EXTENSIONS SPROUTING FROM A SINGLE OUTLET
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS CAN LEAD TO DISASTROUS CONSEQUENCES TO HOME AND FAMILY.
INTENDED TO ALERT THE SERVICE PERSONNEL TO THE
PRESENCE OF IMPORTANT SAFETY INFORMATION IN SERVICE
LITERATURE.
2
SERVICING PRECAUTIONS
CAUTION : Before servicing the DVD covered by this Electrostatically Sensitive (ES) Devices
service data and its supplements and ADDENDUMS, read Some semiconductor (solid state) devices can be damaged
and follow the SAFETY PRECAUTIONS NOTE : if easily by static electricity. Such components commonly are
unforeseen circumstances create conflict between the called Electrostatically Sensitive (ES) Devices. Examples of
following servicing precautions and any of the safety typical ES devices are integrated circuits and some field
precautions in this publications, always follow the safety effect transistors and semiconductor chip components.
precautions.
The following techniques should be used to help reduce the
Remember Safety First: incidence of component damage caused by static electricity.
General Servicing Precautions 1. Immediately before handling any semiconductor

1. Always unplug the DVD AC power cord from the AC component or semiconductor-equipped assembly, drain
power source before: off any electrostatic charge on your body by touching a
(1) Removing or reinstalling any component, circuit board, known earth ground. Alternatively, obtain and wear a
module, or any other assembly. commercially available discharging wrist strap device,
which should be removed for potential shock reasons
(2) Disconnection or reconnecting any internal electrical prior to applying power to the unit under test.
plug or other electrical connection.
(3) Connecting a test substitute in parallel with an
electrolytic capacitor 2. After removing an electrical assembly equipped with ES
devices, place the assembly on a conductive surface
Caution : A wrong part substitution or incorrect such as aluminum toil, to prevent electrostatic charge
polarity installation of electrolytic capacitors may buildup or exposure of the assembly.
result in an explosion hazard.
3. Use only a GROUNDED-tip soldering iron to solder or

2. Do not spray chemicals on or near this DVD or any of its unsolder ES devices.
assemblies.
4. Use only an anti-static solder removal device. Some

3. Unless specified otherwise in this service data, clean solder removal devices not classified a "anti-static" can
electrical contacts by applying an appropriate contact generate electrical charges sufficient to damage ES
cleaning solution to the contacts with a pipe cleaner, devices.
cotton-tipped swab, or comparable soft applicator.
Unless specified otherwise in this service data,
lubrication of contacts is not required. 5. Do not use freon-propelled chemicals. These can
generate electrical charge sufficient to damage ES
devices.
4. Do not defeat any plug/socket B+ voltage interlocks with
witch instruments covered by this service manual might
be equipped. 6. Do not remove a replacement ES device from its
protective package until immediately before you are
ready to install it. (Most replacement ES devices are
5. Do not apply AC power to this DVD and/or any of its packaged with leads electrically shorted together by
electrical assemblies unless all solid-state device heat conductive foam, aluminum foil, or comparable
sinks are correctly installed. conductive material.)
6. Always connect test instrument ground lead to the 7. Immediately before removing the protective material
appropriate ground before connection the test from the leads of a replacement ES device, touch the
instrument positive lead. Always remove the test protective material to the chassis or circuit assembly
instrument ground lead last. into which the device will be installed.
Insulation Checking Procedure Caution : Be sure no power is applied to the chassis or

Disconnect the attachment plug trom the AC outlet and turn circuit, and observe all other safety precautions.
the power on. Connect an insulation resistance meter(500V)
to the blades of the attachment plug. The insulation 8. Minimize bodily motions when handling unpackaged
resistance between each blade of the attachment plug and replacement ES devices. (Normally harmless motion
accessible conductive parts (Note 1) should be more than such as the brushing together of your clothes fabric or the
1M ohm. lifting of your foot from a carpeted floor can generate
Note 1 : Accessible Conductive Parts including Metal static electricity sufficient to damage an ES device.)
panels, input terminals, Earphone jacks, etc.
3
OVERALLBLOCKDIAGRAM
XS1 XS3 XS14
POWER-ON
CD/DVD
LD-DVD
VFDCLK
FORUPDATE
VRDVD
RMC-IN
TOPICKUP TOPOWERASS'Y
LD-CD
L-VCC
VRCD
AVCC
PD1.2
URST
GND
GND
PIC12C508A
GND
VCC
MECHANISM
MD
NC
NC
VC
RF
SW
T+
F+
T-
F-
GND
GND
D
C
E
B
A
F
12V
XS4
-5V
CHANISSIS
6V
6V
MUT-R
5VV NC
LOAD- GND
LOAD+ GND
5VV MUT-L
SP- TV-DVD
SP+ RGB-EN
SL+ 27MHz 4;3/16:9
SL- GND
GND TC4W53 SCART V5V
LIMIT HCU04 -5V
5VV GND
TIN 12V
NC
CV
TOPICKUP 64MSDRAM GND
MECHANISM NC
R-V
CHANISSIS GND
27MHz NC
V5V
GND
NC
B-U
OPTICAL V5V
XS2
SERVO
VO HCU04 &COAXIAL
TOSCART
&TRAY SERVO&DVDPROCESSOR OUTPUT OUTPUTASS'Y
DRIVER MPEG-2DECODER BA7660 S-VIDEO
D5954 &VIDEOENCODER OUTPUT
&BA6287 MT1389SE VIDEO
BA7660 OUTPUT
PDYP
33375STY-5.0
5V
16MFLASH AUDIODAC
RMC
VFDDATA EEPROM AUDIO
NJM4558 OUTPUT
STB
VFDCLK 24C02 29F160 CS4360
GND
5VV
VCC
POWERSW
LED
XS15
TOKEYASS'Y
XS10
FOR
UPGRADE
4
ControlSignals
TROUT
FLASHROM BusofData
TRIN
GND
5VV
Electrical Trouble Shooting Guide
Connection of the unit is correct
Setting of the unit is correct
No
Is power normal? Refer to power guide
Yes
No
Is fluoresce display correct? Refer to display guide
Yes
No
Is open/close normal? Refer to open/close guide
Yes
No
Can disc be read? Refer to read disc guide
Yes
No
Is video normal? Refer to video guide
Yes
No
Is audio is normal? Refer to audio guide
Yes
Normal operation.
A Power Circuit abnormal
Scart
No F301 is open.
XP302 or XP303 is open.
Is C320 AC 220V?
Power cord isn't inserted firmly
or power cord is open.
Yes
No
Check commute circuit.
Is C307 DC 310V?
Check L301 and L302.
Yes
No
Is the voltage between 7,5 pin of N301 15V? Replace N301.
Yes
Check if transformer is damaged.

No
Check secondary commute circuit.
Are transfoemer secondary 7V,5V,12V output? Check secondary feedback circuit.
Check if secondary short.
Check V304.
Yes
No
Check regulated circuit.
Is XP303 normal?
Check N302 and perpheral components.
Yes
Normal
B Display abnormal
Scart
No
Check if screen normal.
Does the screen appear?
Yes
No
Check if connection cord between screen
and decoder ass'y is broken.
Is display normal?
Check if PT6320 pin is connected.
check if pin of screen is connected.
Yes
Normal
C Open/close abnormal
Scart
Is"open"showed on the screen?
Yes
No
Is there voltage difference in XS4

UNLOAD pin and LOAD pin? Check if RMC pin of XS15 have waveform.
No Yes
Yes
No
No
Does XS14 power have voltage?
Does drive motor have voltage?
No
Yes
Yes
Replace key ass'y.

Replace connection cord.
Replace motor.
END
D Read disc abnormal
Disc in
No
Fouse on? Refer to fouse guide.
Yes
No
Is laser normal? refer to laser guide.
Yes
No
Does the disc turn? Refer to fouse guide.
Yes
No
Can TOC be read? Refer to TOC guide.
Yes
Normal
E Video abnormal
Scart
Yes
No picture,no sound. Replace decoder ass'y.
No
Yes
Check jack of output board or replace
No picture,have sound.
decoder ass'y.
No
Yes
Have picture,no color or lolor
Check decoder ass'y and replace G1(27MHz).
disappeared during playback.
No
Yes
Have picture,but picture
Check decoder ass'y and replace G1(27MHz).
disappearedduring playback.
No
END
F Audio abnormal
Have picture,no sound
No
Check if voltage of R,L pin or
Check CS4360 and peripheral components.
CS4360 is normal?
Yes
No
Is N1 signal output? Check NJM4558 and peripheral components.
No
Yes
Is transistor VD2 and VD3 for
Replace transistoe.
mute usage broken down?
Yes
Normal
G Focus abnormal
No focus
No
Does normal voltage at FCS+ Check connection cord.
and FCS- of XS3? Replace pickup.
Yes
Check connection between 14,7 pin of

No
Does normal voltage at 14,7 BA5954 and FCS+,FCS- of XS001.
pin of D001? Check if G1 normal operation.
Check BA5954 and peripheral components.
Yes
No
Check connection between MT1389
Does data output at 59 pin of D2? and BA5954.
Check MT1389 and peripheral components.
Yes
Normal
H Laser abnormal
No laser
Yes Check connection between pickup

Is LD pin of XS3(19,23) 4.5V? and decoder ass'y.
Replace pickup.
No
Yes Check connection between LD pin of

Does voltage at LD pin of D2? MT1389 and LD pin of XS3.
No
No
Does noraml voltage at VCC
pin of D2?
Yes
Normal
I Turn abnormal
Disc doesn't turn
Yes
Check if voltge of SP+ of SP- of XS4
Check connection of mechanism.
are different.
No
Yes
Check if voltage of 11 and 12 pin of Check connections between BA5954 and XS4
D001 are different. Check BA5954 and peripheral components.
No
Yes Check connections between 16 pin of MT1389

Check if voltage of 16 pin of D2 is noraml. and 4,27 pin of BA5954.
No
No Check connections between D001 pins 5,23

Check if data signal of 5,23
and MT1389 pin 18,19.
pin of D001 is normal.
Check D2 and peripheral components.
Yes
Normal
J TOC abnormal
TOC doesn't read
No
Limited switch is closed. Refer to laser guide.
Is laser on? Check slide motor and connections
Is FOK noraml to decoder ass'y
Yes
check connections between A.B.C.D pin of D2

No
Does normal A.B.C.D signal and 5,6,9,10 pin of XS3.
at A.B.C.D pin of D2? Check connections between XS3 and pickup.
Replace pickup.
Yes
No
Does normal RFIN at RFIN pin of MT1389?
Check D2 and peripheral components.
Yes
Yes
Have sound,no picture.? Check MT1389 and peripheral components.
No
Yes
Have picture,no sound.
Check CS4360 and peripheral components.
No
Normal
V501 LTG-0122M
G1
G2
G3
G4
G5
G6
G7
S1
S2
S3
S4
S5
S6
S7
10
11
12
13
14
1
2
3
4
5
6
7
8
9
S501 S502 S503
OPEN/PLAY PLAY PAUSE

X501 S1 VD501
RMC 1 OSB GND 32 1N4148
2 31 S504 S505 S505
DATA DOUT GR1
3 DIN GR2 30 C502
STB
CLK 4 CLK GR2 29 0.1U STOP PREV NEXT
5 SGB GND 28 R504
GND 6 27 S2 VD502
+5V K1 GR4 180
R514 7 26 1N4148
5V R507 R508 R509 51K K2 U503 GND
POWER 10K 10K 10K 8 K3 VDD 25 C503
PT6961 S507
9 VDD GR5 24 100U/6.3V
10 SG1/KS1 GR6 23
11 22 POWER
SG2/KS2 SG12/GR7 S3 VD503
12 SG3/KS3 SG11 21
R502 VD507 13 NC SG10/KS10 20 1N4148
10 LED1 14 SG4/KS4 SG9/KS9 19
15 SG5/KS5 SG8/KS8 18
16 SG6/KS6 SG7/KS7 17
R506
RMC 1
GND 2 4.7K
VCC 3
R522
1K
U501
C501 C502
100U/6.3V 0.1U
R511
10K
R512
10K
R510
10K
DVP767 KEY CIRCUIT DIAGRAM

R404
100k
R438 V401 R405 R407

100 8050
3 1 100k 10k
RP401 R417 +
R408 C405
C415 10k 10k 47u/16v
3
100u/16v
+
2
R416
4.7k
VD401 + C419
5.6v C416 0.1 C418 +
C417 R411
1
C414 0.1 0.1

100u/16v 47u/16v 100
+
C411
1
C410
0.1 100u/16v
cci
vcc
ref
op1out cco
vco
dgnd
agnd
op2out clk-
PT2399
N403B
o
N402
C403 1/2 4558
4.7/50 5 + V402
lf2out
lf1out
vcc
op1i
op2i
3 9014 1
f2in
f1in
+
7
n
out2
lp
lp
p
p
6 - R414
C413 2k
R401
10
11
12
13
14
15
16
4.7/50
9
100k R409
2
12k
R439
R412 2k
C421 C424
0.1 C422 510p C406 XP401
3k
0.1 C423 20p
510p + C408 1
X401 47/16 2
N401A @ 3
1/2 4558 12v 4
5
4
C404 R403
1/50 1k R420
+
3 R421
vdd
+ R419 15k R418

o1 1 10k 10k 6.8k R423
2 - 10k
R427 R428
R413 4.7k 10k C430
R402 2k R425 10u/16v
+ C409 10k
+
15k
10u/16V R410
+
C429
120k C427 4.7/50
+
C407 22u/16v
20p
C420
5n6
C412
+
+ C426 R426
4.7/50 C428 3n9 R424
C425 30k 100k
3
10u/16v
5n6
3
R415
10k
2 RP404
1
2 RP403
1
2
DVP767 MIC CIRCUIT DIAGRAM

R315
180
4 1 V301 UTC431
R305
3 2 NC
C321 V304
334 C307
VD301-VD304
HS817 104
IN4007 VD308 R313 R312

SR560 R314 4.7k 3.6k
- + 100K
5 6
R302 C306 7 R325 L305

C301 103/630V NC 20UH
47U/400V 47K/2W C308 C318
3 8 VD310 1000U 1000U
L302 SF16
2 9
HGL-UF103A 10
VD305 1
SF16 11
R310
L301 47 R309 N306
LV-R1487 T301 2K MC33375ST-5.0T3
C302 L304 BCK-A85 1 3
GND
1
22U/50V ZRF253L IN OUT
2 V307 CON
C326 8550d C311
47UF R308 22U/50V
2
820
3
C320 47P/1KV
3
0.22U/280V C303
V306 2
9014
VD306 VD316 VD310 R326
SF16 R311 4.7K
1
HER108 L303 SF16
4.7K +5V
N305
79L05 GND
1 3
XP305
GND
F301 ZBF253L IN OUT -5V
C326
22U/50V
C319
2
T1.6A 250V 47U/50V on/off
D8
D7
D6
Vstat 5
N301 N304 5.5V

79L05
DM0265RN 1 3 1 3
GND
IN OUT
V302 5.5V
4 I_limit
1GND
R329
2VCC
9014
3 Vfb
C312 R318 1 3 680/.25w C325

47U/50V 220K 22U/50V GND
2
V303
9014
GND
2
R321
R319 4.7K
33K
-5V
230VAC/50HZ
3 1
+12V XP303
V305 R320
8550d 6.8K VD315
C305
2
HZ12A1
4700P/400V
AD85UAHPOWERCIRCUITDIAGRAM
+5V
R442 10K
+5V
C402 + R447 10
C398 390P R443 104
C325
10 R348
R430 3K
C385 8.2K C389
C400 + C399
+
104
1N5 + C322 C332 33P
47K
R429 8 R350
C384 8.2K R441 1.8K 8 R344 2
V+ L315 L600
V+ C359 47K C320 -
+
2 - 1
1 3
+
3
+ C324 R451 100
+ R439 000 C396 R345 C403 VD361
R435 R440 1.8K C397 R346 601
NC 4558 120P
3K N302
10K 390PN304 4558
100K 1
R438 R338 5 C327 L316 L600
5 000 C394 47K C321 + 7 2
+
C387 R431 8.2K R433 1.8K +
+
7 6 - R452 100 C404
+
6 - V- 4 3
V- 4 R347 VD362
R434 10 R339 C380 R448 120P 601 4
C390 R445 C393 R449 3K 100K C326 +
10K C391 C401 + 47K 104 10 X301
XP302 1N5 104 104
C388 R432 8.2K R436 1.8K 390P R444 5V
1 R349 3K C333 33P
+
1 --5V
2
2 GND C392 390P --5V R82
R350
XP301 + C323 R351 47K 10K
3
3 R437 10K 47K R83 10K 709
1 XP303 R472 10K VD18
2 3
VD17 +5V
601 XP303
1 VD19 ISS355 R85 1K
4 5
000 2 5
R461 6 7
3 4
8 9 GND VD358
10 11
4 5V VD352 ISS355 R480
3
+5V
R463 5 2
000 R460 000 12 13 ISS355
1
14 15 1K
R77
16 17
R462 10K
18 19 R78 10K 709
000
20 21
R31 10K +5V R471 10K VD15
VD14 1K
C31 560P R32 601 VD16 ISS355 R80
10
NC R19 VD359
R455 R454 C19 8.2K C22 2.7N +5V R79
C33 + C32
+
104 NC
000 NC ISS355
R456 R453
R18 1K
C18 8.2 R30 1.8K 8 R475 R52 VD353 ISS355 R481
R466 C407 2
V+ C28 100 L321 L600
+
000 R458 - 1
10K
+
000 R459 104
3 + R28 000 C29 R53 10K 709 VD354 ISS355
000 R24 R29 1.8K C30 NC C417
000 10K 560P R479 10K VD350
4558 120P
N2 VD349
R27 R476 601 VD355 ISS355 R482
C21
5 + 000 100 L322 L600 +5V 1K
R20 8.2K R22 1.8K 7
+
6 R483
+
- 4 R33 C27 C418 R487 VD356 ISS355
R23
V- 10 C26
C23 R34 NC 120P 10K 1K
48
47
46
45
44
43
42
41
40
39
38
37
10K C24 C34 + R488 10K 709

2.7N 104 VD357 ISS355
C20 R26 8.2K R25 1.8K 560P R470 10K VD370 R484
+5V VD369
+
1 36 601 R54 1K
2
3
35
34
C25 560P --5V NC
R498
4 33 R1 R485
5 D501 32 NC
L317 R26 10K
6 31 L318 10K 1K
7 PT6320 30 R2
+ C405 10K 709
C406 8 29 + C412
L600 9 28 C413 R469 10K VD2
104 10 27 L600 VD1
11 26 104 601 R490 1K
12 25 VD365
+5V R3 601
13
14
15
16
17
18
19
20
21
22
23
24
NC
R5
10K
R6 10K 709 R4 1K
VD366
R468 10K VD4 601
VD3 1
601
2
R7 +5V
3
NC R8 1K
R9 VD367 4
601
R48 10K +5V R10
10K X302
10K 709
R465 NC C409 + C408
C48 560P R49 R467 10K VD6
R464 104 VD5
000 C414 10 601 R12 1K
R36 VD368
104 C36 8.2K C39 2.7N 601
C50 + C49 R11
+
104 U301 R301

NC OPT OUT
220
C411 + C410 1
R35 R304 10 D-IN
104 C35 8.2K R47 1.8K R477
8 2
2
V+ C45 100 L323 L600 +5V VCC
+
- C383
+
1 3
C304 + C302 GND
3 + R45 000 C46 120P
R41 R46 1.8K C47 C419 104
NC R302
10K 560P
N3 4558 120P C301 330 L301 L600 X301
R44 R478 104 1
5 000 100 L324 L600
C38 R37 8.2K R39 1.8K + 7 C303
+
6 R303
+
- 4 R50 C44 C420 120P

R40
V- 000 91
C40 R51 C43 120P
10K 2.7N C41 C51 +
104 NC D301
1
C37 R38 8.2K R42 1.8K 560P
74HCU04
+
C42 560P --5V
10
11
12
13
14
8
9
R43 10K
DVP767 OUTPUT CIRCUIT DIAGRAM

DVP767KUH KEY BOARD DIAGRAM
DVP767M3 MIC BOARD DIAGRAM OUT767 OUTPUT BOARD DIAGRAM

AD85UAH POWER BOARD DIAGRAM DHC777 DECODER BOARD DIAGRAM
ELECTRICAL PARTS LIST
PART No. PART NAME Q'TY
DVP767
21490 DHC777 DECODER ASS'Y 1
S7494 D767KNH3 KEY ASS'Y 1
21492 OUT767 OUTPUT ASS'Y 1
S7527 D767M3(AU) MIC ASS'Y 1
S7468-3 AD85NAH-B-L-AU POWER ASS'Y 1
S2701 7# BATTERY 2
S2684 VDE POWER CORD 1
S8101 SL260 LOADING ASS'Y 1
S1658e DVP767 OWNER MANUAL 1
S8501 SCART COMMUTATOR 1
S3022 RCA CORD VIDEO 1
S3035 RCA CORD AUDIO 1
S3134 CC-1.0×12×270 1
S3451 CC-1.0×21×70 1
S3251h CC-0.5×24×210-MT(8+/-0.5) 1
S3709 CC-1.0×8×140 1
S0692e DC-380H REMOTE CONTROLLER (WHITE) 1
REF No. PART No. PART NAME REF No. PART No. PART NAME
D767KNH3 KEY ASS'Y a9198 KEY CONNECTOR WIRE
S501 a6434 TOUCH EVQ11L04W D767M3(AU) MIC ASS'Y
S502 a6434 TOUCH EVQ11L04W RESISTOR
S503 a6434 TOUCH EVQ11L04W R401 G0753 RT13-0.167W-100K±5%
CAPACITOR R409 G0737 RT13-0.167W-12K±5%
C501 a3540 CD110-6.3V-100uF±20% R410 G0754 RT13-0.167W-120K±5%
C502 a3304 CT4D-2F4-63V-0.1uF-S R411 G0705 RT13-0.167W-10±5%
C503 a3540 CD110-6.3V-100uF±20% R412 G0724 RT13-0.167W-3K±5%
C504 a3304 CT4D-2F4-63V-0.1uF-S R413 G0721 RT13-0.167W-2K±5%
RESISTOR R414 G0721 RT13-0.167W-2K±5%
R502 G0705 RT13-0.167W-10±5% R415 G0735 RT13-0.167W-10K±5%
R504 G0714 RT13-0.167W-180±5% R417 G0735 RT13-0.167W-10K±5%
R506 G0728 RT13-0.167W-4.7K±5% R418 G0731 RT13-0.167W-6.8K±5%
R507 G0735 RT13-0.167W-10K±5% R419 G0735 RT13-0.167W-10K±5%
R508 G0735 RT13-0.167W-10K±5% R420 G0738 RT13-0.167W-15K±5%
R509 G0735 RT13-0.167W-10K±5% R421 G0735 RT13-0.167W-10K±5%
R510 G0735 RT13-0.167W-10K±5% R423 G0735 RT13-0.167W-10K±5%
R511 G0735 RT13-0.167W-10K±5% R424 G0743 RT13-0.167W-30K±5%
R512 G0735 RT13-0.167W-10K±5% R425 G0735 RT13-0.167W-10K±5%
R514 G0749 RT13-0.167W-51K±5% R427 G0728 RT13-0.167W-4.7K±5%
R522 G0719 RT13-0.167W-1K±5% R428 G0735 RT13-0.167W-10K±5%
R523 G0785 RT13-0.167W-510±5% R438 G0705 RT13-0.167W-10±5%
LED R439 G0721 RT13-0.167W-2K±5%
Q500 a1576 RED LED RHEOSTAT
V500 a7371 LTG-0122M RP401 a0648a WH09JT11-B503-F30
DIODE RP403 a0511 WH0615-22K
VD501 a5004 1N4148 RP404 a0640 WH0615-47K
VD502 a5004 1N4148 CAPACITOR
VD503 a5004 1N4148 C403 a3508 CD110-16V-4.7uF-M
VD504 a5004 1N4148 C404 a3505 CD110-1u-M-16V
IC C406 a2015 CC1-63V-05B-20K-CH
D500 P90294 PT6961 C407 a2015 CC1-63V-05B-20K-CH
SOCKET C408 a3512 CD110-47u-M-16V
XP500 P7075 8 PINS SOCKET C409 a3509 CD110-16V-10u-M
OTHER C410 a3513 CD110X-16V-100u-M
RMC500 a6733 HS0038B RECEIVER C411 a3304 CT4D-2F4-63V-0.1uF-S
C412 a3508 CD110-16V-4.7uF-M C302 a3607 CD110X-22uF-M-50V
C413 a3508 CD110-16V-4.7uF-M C303 a2063 CC81-06B-47K-1KV-SL
C415 a3513 CD110X-16V-100u-M C306 a2544 CBB21-103J-630V
C416 a3304 CT4D-2F4-63V-0.1uF-S C307 a2056 CS1-06B-104Z-63V-Y5V
C417 a3512 CD110-16V-47uF-M C308 a3676 CD288-1000uF-M-10V
C418 a3304 CT4D-2F4-63V-0.1uF-S C312 a3210 CD110X-47uF-M-50V
C419 a3304 CT4D-2F4-63V-0.1uF-S C318 a3676 CD288-1000uF-M-10V
C420 a3044 CL11-100V-5600P-K C320 a3447 CIS-0.22uF-280VACX2-K
C421 a3304 CT4D-2F4-63V-0.1uF-S C321 a3307 CT4D-2F4-0.33uF-63V-S
C422 a3304 CT4D-2F4-63V-0.1uF-S C325 a3607 CD110X-22uF-M-50V
C423 a2038 CC1-63V-10B-511K-SL C3051 a2081 CT81-18B-2E4-472M-400VAC-YA
C424 a2038 CC1-63V-10B-511K-SL DIODE
C425 a3044 CL11-100V-5600P-K VD301 a5005b 1N4007-YH
C426 a3041 CL11-100V-3900P-K VD302 a5005b 1N4007-YH
C427 a3510 CD110-16V-22uF-M VD303 a5005b 1N4007-YH
C428 a3509 CD110-16V-10u-M VD304 a5005b 1N4007-YH
C429 a3508 CD110-16V-4.7uF-M VD305 a1202a SF16-YG
C430 a3509 CD110-16V-10u-M VD306 a1205c HER108-YH
C450 a3304 CT4D-2F4-63V-0.1uF-S VD308 a5136 SR560(BL)
C451 a3513 CD110X-16V-100u-M VD310 a1202a SF16-YG
OTHER TRIODE.IC
V402 a5009a C9014C N301 a4764 DM0265R
N401 a4042b UTC4558 N304 a4766 79L05
N402 a4503 PT2399 V301 a4557a UTC431
X401 a6871b CKX-6.35-7 JACK V302 a5009a C9014C
XP401 a9246 MIC WIRE V303 a5009a C9014C
AD85NAH-B-L-AU POWER ASS'Y V304 a5094 HS817
RESISTOR V305 a5104a C8550D
R302 a0472 RY27-2W-47K±5% INDUCTOR
R312 G0909 RT13-0.167W-3.6K±5% L301 a6686 LV-R1487 FILTER
R313 G0728 RT13-0.167W-4.7K±5% L302 a7279 HGL-UF103A
R314 G0753 RT13-0.167W-100K±5% L303 a7020 Reluctance jumper ZBF253L-4
R315 G0714 RT13-0.167W-180±5% L304 a7020 Reluctance jumper ZBF253L-4
R318 G0759 RT13-0.167W-220K±5% L305 a6621 COIL-0.02mH
R319 G0744 RT13-0.167W-33K±5% OTHER
R320 G0728 RT13-0.167W-4.7K±5% T301 a7443 BCK-A85 Transformer
R321 G0731 RT13-0.167W-6.8K±5% XP302 a7278 2 pins connector
R329 G0036 RT14-0.25W-470±5% XP303 a9175 DC power cord
CAPACITOR F301 a6763 FUSE 61801.6M
C301 a2548 CD288-47uF-M-400V(18X20) a6443 FC502H FUSE HOLDER
OUT767 OUTPUT ASS'Y R48 P11013 RC-03K103JT
RESISTOR R49 P11003 RC-03K100JT
R1 P11013 RC-03K103JT R50 P11003 RC-03K100JT
R2 P11013 RC-03K103JT R52 P11013 RC-03K103JT
R4 P11009 RC-03K102JT R53 P11013 RC-03K103JT
R5 P11013 RC-03K103JT R77 P11013 RC-03K103JT
R6 P11013 RC-03K103JT R78 P11013 RC-03K103JT
R8 P11009 RC-03K102JT R80 P11009 RC-03K102JT
R9 P11013 RC-03K103JT R82 P11013 RC-03K103JT
R10 P11013 RC-03K103JT R83 P11013 RC-03K103JT
R12 P11009 RC-03K102JT R85 P11009 RC-03K102JT
R18 P11055 RC-03K822JT R301 P11071 RC-03K221JT
R19 P11055 RC-03K822JT R302 P11024 RC-03K331JT
R20 P11055 RC-03K822JT R303 P11167 RC-03K910JT
R21 P11055 RC-03K822JT R304 P11003 RC-03K100JT
R22 P11028 RC-03K182JT R338 P11209 RC-03K443JT
R23 P11013 RC-03K103JT R339 P11052 RC-03K302JT
R24 P11013 RC-03K103JT R344 P11209 RC-03K443JT
R25 P11028 RC-03K182JT R345 P11052 RC-03K302JT
R26 P11013 RC-03K103JT R346 P11019 RC-03K104JT
R27 P11006 RC-03K101JT R347 P11019 RC-03K104JT
R28 P11006 RC-03K101JT R348 P11052 RC-03K302JT
R29 P11028 RC-03K182JT R349 P11052 RC-03K302JT
R30 P11028 RC-03K182JT R350 P11018 RC-03K473JT
R31 P11013 RC-03K103JT R351 P11018 RC-03K473JT
R32 P11003 RC-03K100JT R429 P11055 RC-03K822JT
R33 P11003 RC-03K100JT R430 P11055 RC-03K822JT
R35 P11055 RC-03K822JT R431 P11055 RC-03K822JT
R36 P11055 RC-03K822JT R432 P11055 RC-03K822JT
R37 P11055 RC-03K822JT R433 P11028 RC-03K182JT
R38 P11055 RC-03K822JT R434 P11013 RC-03K103JT
R39 P11028 RC-03K182JT R435 P11013 RC-03K103JT
R40 P11013 RC-03K103JT R436 P11028 RC-03K182JT
R41 P11013 RC-03K103JT R437 P11013 RC-03K103JT
R42 P11028 RC-03K182JT R438 P11000 RC-03K000JT
R43 P11013 RC-03K103JT R439 P11000 RC-03K000JT
R44 P11006 RC-03K101JT R440 P11028 RC-03K182JT
R45 P11006 RC-03K101JT R441 P11028 RC-03K182JT
R46 P11028 RC-03K182JT R442 P11013 RC-03K103JT
R47 P11028 RC-03K182JT R443 P11003 RC-03K100JT
R444 P11003 RC-03K100JT C18 a3594 CD11CX-47uF-M-16V
R449 P11018 RC-03K473JT C22 P20042 GRM39B222K50PT
R461 P11000 RC-03K000JT C33 P20015 GRM39F104Z25PT
R483 P11009 RC-03K102JT C303 P20020 GRM39CH121J50PT
CAPACITOR C325 a3594 CD11CX-47uF-M-16V
C326 a3594 CD11CX-47uF-M-16V C421 P20015 GRM39F104Z25PT
C327 a3594 CD11CX-47uF-M-16V C422 P20015 GRM39F104Z25PT
C332 P20026 GRM39CH330J50PT C423 P2000 GRM39CH150J50PT
C333 P20026 GRM39CH330J50PT C424 P2000 GRM39CH150J50PT
C380 P20015 GRM39F104Z25PT C425 P2000 GRM39CH150J50PT
C383 P20015 GRM39F104Z25PT R34 P20015 GRM39F104Z25PT
C384 a3594 CD11CX-47uF-M-16V R51 P20015 GRM39F104Z25PT
C385 a3594 CD11CX-47uF-M-16V R445 P20015 GRM39F104Z25PT
C387 a3594 CD11CX-47uF-M-16V MULTILAYER CHIP INDUCTOR
C388 a3594 CD11CX-47uF-M-16V L301 P6817 BSZ2012-600T
C389 P20010 GRM39B152K50PT L315 P6817 BSZ2012-600T
C399 a3594 CD11CX-47uF-M-16V DIODE
C400 P20015 GRM39F104Z25PT VD16 P1200 1SS355TE Switch Diode
C401 a3594 CD11CX-47uF-M-16V VD19 P1200 1SS355TE Switch Diode
C403 P20020 GRM39CH121J50PT VD353 P1200 1SS355TE Switch Diode
C411 P20015 GRM39F104Z25PT TRIODE
C412 a3594 CD11CX-47uF-M-16V VD1 P5073a 2SD601AR
C413 P20015 GRM39F104Z25PT VD2 P5700 2SB709AR
C414 P20015 GRM39F104Z25PT VD3 P5073a 2SD601AR
C415 P20020 GRM39CH121J50PT VD4 P5700 2SB709AR
C416 P20020 GRM39CH121J50PT VD5 P5073a 2SD601AR
REF No. PART No. PART NAME
VD18 P5700 2SB709AR
VD349 P5073a 2SD601AR
VD350 P5700 2SB709AR
VD361 P5073a 2SD601AR
VD362 P5073a 2SD601AR
VD365 P5073a 2SD601AR
VD366 P5073a 2SD601AR
VD367 P5073a 2SD601AR
VD368 P5073a 2SD601AR
VD369 P5073a 2SD601AR
VD370 P5700 2SB709AR
IC
D301 P4516 SN74HCU04DR
D302 P90252 CS4362-KQ
N2 P4577 LM833M
N3 P4577 LM833M
N303 P4577 LM833M
N304 P4577 LM833M
SOCKET
U2 a7294 TX179AP
X303 a6936 AV-8.4-4A
X304 a7539 AV4-RWRW
X305 a7292 AV4-BBRW-757
XP301 a7244 FABSD2152
XP303 a6511 B-6B-PH

Manual Service MT1389se

Uploaded by

Copyright:

Available Formats

Manual Service MT1389se

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Manual Service MT1389se

Uploaded by

Copyright:

Available Formats

SERVICE MANUAL MODEL

DVD and CD CONTENTS

PLAYER SERVICE PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . 2,3

6. ALL CRITICAL COMPONENTS SUCH AS FUSES. FLAMEPROOF RESISTORS, SUBJECT: IMPLOSION

General Servicing Precautions 1. Immediately before handling any semiconductor

3. Use only a GROUNDED-tip soldering iron to solder or

4. Use only an anti-static solder removal device. Some

Insulation Checking Procedure Caution : Be sure no power is applied to the chassis or

XS1 XS3 XS14

Connection of the unit is correct

Setting of the unit is correct

Check if transformer is damaged.

Is"open"showed on the screen?

Is there voltage difference in XS4

Does drive motor have voltage?

Replace key ass'y.

Have picture,no sound

Check connection between 14,7 pin of

Yes Check connection between pickup

Yes Check connection between LD pin of

Disc doesn't turn

Yes Check connections between 16 pin of MT1389

No Check connections between D001 pins 5,23

TOC doesn't read

check connections between A.B.C.D pin of D2

OPEN/PLAY PLAY PAUSE

DVP767 KEY CIRCUIT DIAGRAM

R438 V401 R405 R407

C414 0.1 0.1

+ R419 15k R418

DVP767 MIC CIRCUIT DIAGRAM

IN4007 VD308 R313 R312

R302 C306 7 R325 L305

N301 N304 5.5V

C312 R318 1 3 680/.25w C325

10K C24 C34 + R488 10K 709

104 U301 R301

- 4 R50 C44 C420 120P

C42 560P --5V

DVP767 OUTPUT CIRCUIT DIAGRAM

DVP767M3 MIC BOARD DIAGRAM OUT767 OUTPUT BOARD DIAGRAM

You might also like