DM74LS73A Dual Negative-Edge-Triggered Master-Slave J-K Flip-Flops with Clear and Complementary Outputs
August 1986 Revised March 2000
DM74LS73A Dual Negative-Edge-Triggered Master-Slave J-K Flip-Flops with Clear and Complementary Outputs General Description This device contains two independent negative-edge-triggered J-K flip-flops with complementary outputs. The J and K data is processed by the flip-flops on the falling edge of the clock pulse. The clock triggering occurs at a voltage level and is not directly related to the transition time of the negative going edge of the clock pulse. The data on the J and K inputs is allowed to change while the clock is HIGH or LOW without affecting the outputs as long as setup and hold times are not violated. A low logic level on the clear input will reset the outputs regardless of the levels of the other inputs.
Ordering Code: Order Number DM74LS73AM DM74LS73AN Package Number M14A N14A Package Description 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150 Narrow 14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300 Wide
Devices also available in Tape and Reel. Specify by appending the suffix letter X to the ordering code.
Connection Diagram
Function Table Inputs CLR L H H H H H CLK X H J X L H L H X K X L L H H X Q0 Q L Q0 H L Toggle Q0 Outputs Q H Q0 L H
H = HIGH Logic Level L = LOW Logic Level X = Either LOW or HIGH Logic Level = Negative going edge of pulse. Q0 = The output logic level before the indicated input conditions were established. Toggle = Each output changes to the complement of its previous level on each falling edge of the clock pulse.
2000 Fairchild Semiconductor Corporation
DS006372
www.fairchildsemi.com
DM74LS73A
Absolute Maximum Ratings(Note 1)
Supply Voltage Input Voltage Operating Free Air Temperature Range Storage Temperature Range 7V 7V 0C to +70C 65C to +150C Note 1: The Absolute Maximum Ratings are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum ratings. The Recommended Operating Conditions table will define the conditions for actual device operation.
Recommended Operating Conditions
Symbol VCC VIH VIL IOH IOL fCLK fCLK tW Supply Voltage HIGH Level Input Voltage LOW Level Input Voltage HIGH Level Output Current LOW Level Output Current Clock Frequency (Note 2) Clock Frequency (Note 3) Pulse Width (Note 2) tW Pulse Width (Note 3) tSU tSU tH tH TA Clock HIGH Preset LOW Clear LOW Clock HIGH Preset LOW Clear LOW Setup Time (Note 2)(Note 4) Setup Time (Note 3)(Note 4) Hold Time (Note 2)(Note 4) Hold Time (Note 3)(Note 4) Free Air Operating Temperature 0 0 20 25 25 25 30 30 20 25 0 5 0 70 ns ns ns ns C ns ns Parameter Min 4.75 2 0.8 0.4 8 30 25 Nom 5 Max 5.25 Units V V V mA mA MHz MHz
Note 2: CL = 15 pF, R L = 2 k, TA = 25C and VCC = 5V. Note 3: CL = 50 pF, R L = 2 k, TA = 25C and VCC = 5V. Note 4: The symbol () indicates the falling edge of the clock pulse is used for reference.
www.fairchildsemi.com
DM74LS73A
Electrical Characteristics over recommended operating free air temperature range (unless otherwise noted) Symbol VI VOH VOL Parameter Input Clamp Voltage HIGH Level Output Voltage LOW Level Output Voltage II Input Current @ Max Input Voltage IIH HIGH Level Input Current IIL LOW Level Input Current IOS ICC Short Circuit Output Current Supply Current Conditions VCC = Min, II = 18 mA VCC = Min, IOH = Max VIL = Max, VIH = Min VCC = Min, IOL = Max VIL = Max, VIH = Min IOL = 4 mA, VCC = Min VCC = Max VI = 7V VCC = Max VI = 2.7V VCC = Max VI = 0.4V VCC = Max (Note 6) VCC = Max (Note 7) J, K Clear Clock J, K Clear Clock J, K Clear Clock 20 4 2.7 3.4 0.35 0.25 0.5 0.4 0.1 0.3 0.4 20 60 80 0.4 0.8 0.8 100 6 mA mA mA A mA Min Typ (Note 5) Max 1.5 Units V V
Note 5: All typicals are at VCC = 5V, TA = 25C. Note 6: Not more than one output should be shorted at a time, and the duration should not exceed one second. For devices, with feedback from the outputs, where shorting the outputs to ground may cause the outputs to change logic state, an equivalent test may be performed where VO = 2.125V with the minimum and maximum limits reduced by one half from their stated values. This is very useful when using automatic test equipment. Note 7: With all outputs OPEN, ICC is measured with the Q and Q outputs HIGH in turn. At the time of measurement, the clock is grounded.
Switching Characteristics at VCC = 5V and TA = 25C From (Input) Symbol Parameter To (Output) CL = 15 pF Min fMAX tPHL tPLH tPLH tPHL Maximum Clock Frequency Propagation Delay Time HIGH-to-LOW Level Output Propagation Delay Time LOW-to-HIGH Level Output Propagation Delay Time LOW-to-HIGH Level Output Propagation Delay Time HIGH-to-LOW Level Output Clear to Q Clear to Q Clock to Q or Q Clock to Q or Q 30 20 20 20 20 Max 25 28 24 24 28 RL = 2 k CL = 50 pF Min Max MHz ns ns ns ns Units
Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILDS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 5 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com
