Design of Fixture
Design of Fixture
Design of Fixture
DESIGN OF FIXTURES
Introduction
A fixture is a device for holding a work piece during machining operation. The name is
derived from the fact that a fixture is always fastened to a machine or bench in a fixed position. It
does not contain special arrangements for guiding the cutting tool, as drill jigs do. In a setup using a
fixture the responsibility for accuracy depends upon the operator and the construction of the
machine tool.
Other types of tooling used for positioning parts relative to each other for fabricating
purpose are also commonly referred to as fixture. Assembly fixtures and weld fixtures are example
of this type.
Many machining operations can be performed by clamping the work piece to the machine
table without using a fixture, especially when a few parts are to be machined. However, when the
number of parts is large enough to justify its cost, a fixture is generally used for holding and
locating the work.
Types of Fixtures
Examples of common types of fixtures are vise, milling, boring, broaching, lathe and
grinding. Each will be described in the following section.
1. Vise Fixtures:
Standard machine vises adopted with special jaws provides an easy way on holding
parts for machining. They may be used with various types of machine tools and therefore may be
classed as a type of fixture by themselves.
All machinists know that is very easy to clamp a work piece with parallel sides in a vise
but that work pieces with round or irregular contours are very difficult to clamp properly. It is also
well known that unless precautions are taken, the clamping action of vise jaws is likely to mar
finished surfaces. Special jaws are designed to hold work pieces with irregular contours properly
and at the same time avoid damaging important surfaces.
When it is necessary to hold the work piece firm against pressure in all directions the
wedge type jaws may b useful. All the jaws considered up to now here held the work piece more or
less in vertical position. However, many work pieces requires surfaces machines at a specified
angle other than 90o for these workspaces. One of the jaws is recessed to take the work piece at the
proper angle.
Small casting or forgings with irregular contours can be held in standard machine vises
by using epoxy resin to from a nest within the vise jaws to fit the irregular contour.
2. Milling Fixture
A mill fixture holds the parts in the correct relation to the milling cutter as the table
movement carries the parts through the cutters. It consists of five main parts, the base, clamps, rest
blocks or rest, locating points and gauging surfaces.
i) The Base:
The base of a mill fixture consists of a base plate which has a flat and
accurate undersurface and forms the main body on which various components are mounted. A
heavy base is the most important element of a milling fixture. The complete fixture is built up from
this plate, Keys are provided on the under surface of the plate which are used for easy and accurate
Roll # 08MR-20 1 / 4
CH # 04 Tool Design
aligning on the fixture on the milling machine table by inserting them into one of the T-slots in the
table.
d) Indexing fixture: Work piece is indexed into the next position during the
machining cycle of the mill.
e) Rise and fall fixtures: These fixtures allow rising and lowing of the work
piece in conjunction with the mill feed.
3. Lathe Fixtures
A large majority of lathe operations can be accomplished by using standard chucks and
holding methods. However, many parts such as casting and forging cannot readily be mounted
by any of the standard methods. It is therefore necessary to manufacture special work-holding
fixtures for machining these parts.
The basic principles of fixture design apply to lathe fixtures. However, these are
additional considerations that apply specially to lathe fixtures, since the fixture and the work
piece revolve. They are as follow:
1- Clamps and other holding devices should be designed in such a way that they will
not be loosened by centrifugal force.
2- The work piece should be gripped on its largest diameter, and whenever possible
the gripping diameter should be larger than the diameter being machined.
3- The fixture should be well balanced. Irregular-shaped work pieces may have to be
counterweighted to prevent vibration. It is not necessary to achieve prefect balance unless
the work piece is rotating at high speeds.
4- The fixture should be as light as possible, since it is rotating.
5- Projections and sharp corners should be avoided as the operator may not be able to
see them while the tool is rotating.
6- Thin section of the work pieces may require support to resist the pressure of the
lathe tool.
Lathe holding methods are usually some adaptation of chucks, faceplates and mandrels or a
combination of the three. Each of the foregoing methods has a standard counterpart, such as
three-jaw universal chucks, spring collets, rubber flex collets, standard mandrels etc. Such
standard work-holding methods are universal, i.e. they will hold a variety of work sizes as long
as they are of the same shape or geometry.
Chucks: - Widely used lathe holding devices are universal self-centering scroll chucks with
two, three, four and six jaws and independent four-jaw chucks used for odd-shaped work
pieces. There are several variations, such as combination chucks with self-centering and
independent jaw action and jaw powered by air or hydraulic cylinders on the rear of the
spindle.
Special top jaws may be designed for better fit to the gripping diameter of the work piece.
Standard jaws usually will not be in full contact with the work piece. Soft top-jaw blanks
available from chuck companies can be machined to the desired shape directly on the chuck.
The jaw height should be kept short inn order to grip parts as close to the chuck face as
possible. The finished jaw may be hardened or left soft as desired.
circular bases indicating grooves or accurately machined holes for the purpose of aligning the
fixture by a dial indicator.
4. Grinding Fixtures
The design of grinding fixtures is basically the same as the design of fixtures for
use on other machine tools. For instance, there is little difference in a mill fixture and a
fixture to be used on surface grinder. Likewise, a lathe fixture is similar to a fixture
designed for use on a cylindrical grinder. There are, however, conditions unique to the
grinding process that must be taken into consideration.
The grinding process is usually a finishing operation where the work piece
dimensions are held to close tolerance; therefore great accuracy is required in the design
and construction of grinding fixture. Work pieces cannot deflect under clamping
pressure and locating methods must be precise and exacting. Location of work pieces is
made easier, however, since by the time they are ready for grinding, most work pieces
have sufficient machined surface by which they can be positioned and held.
For the time of grinding at the point of grinding heat generated at the point of
grinding-wheel contact is controlled by a heavy application of coolant. Coolant nozzles
must be designed properly and located where they will do the most good. The entire
contact zone between the wheel and work should be flooded with an abundant supply of
clean coolant. It should be applied in large quantities under very little pressure.
Roll # 08MR-20 4 / 4