Bs 205 0512e

1
CONTENTS
Introductions . . . . . . . . . .
The Features of BS-205 . .
Technical Specification . .
Dimensions . . . . . . . . . . . . .
Front Panel . . . . . . . . . . . .
Rear Panel . . . . . . . . . . . . . . 9
Parameter . . . . . . . . . . .
16
ZERO Calibration
21
. . . . . . .
Actual Load Calibration
. . . 22
Equivalent Calibration . . . 24
Comparator Data
. . . . . . .
26
. . . . . . . . .
34
Key Lock . . . . . . . . . . .
36
Option
37
Hold Function
. . . . . . . . . . .
Error Message
and Trouble Shooting . . .
47
2
Introduction
1. Introduction
Thank you for purchasing BS-205 High precision digital indicator.
Check for any breakdown during transit and discrepancy of the
specification. Always keep this manual at hand.
The BS-205 Series are configured as follows :
Check that there is no discrepancy between the model and its
specifications you have chosen when ordering and the model and its
specifications under your hand.
In order to obtain the highest performance of your BS-205, thoroughly
read this manual before use.
2. Precautions
Place the indicator on a flat and stable surface.
Applying voltage and current exceeding the maximum permissible

value results in the breakdown of the meter.
Do not severely press because the light pressing of keys can incite
the operation.
Do not subject the scale to sudden temperature changes.

Operating temperature : -10~+50
Keep the scale away from strong EMI noises may cause incorrect
weight readings.
Keep the main body from rain and keep in dry area.
Do not use inflammable materials in cleaning.
The contents of this manual are subject to change without notice

for further improvement.
3
The Features of BS-205
1. Features
Appropriate for weight and measurement system.
24 bit Sigma-Delta A/D converter for high accuracy.
Simple full digital calibration.
Simulative (mV/V memory) or live load calibration.
Watchdog circuitry (system restoration)

Weight Back-up (power on actual weight)
2. Main Function
Various specification of weight conversion speed.
(Digital Filter Function)
3 Set point relay output.
Hold, peak hold and auto zero.
Option serial output or analog output.
User can set the max. weight which users want to and division
at ones disposal.
4
Technical Specification
1. Analog Input & A/D Conversion
Analog signal input range
0 mV ~ 20 mV
Non-linearity
0.01% F.S. max.
Max. Display resolution
1/20,000
Min. Input sensitivity
0.5V/Digit (min.)
Temperature drift
Zero : 0.1 V/ RTI max.

Span : 10ppm/ max.
Load cell excitation
DC 5V 5%, 60
Voltage
up to 4 x 350 ohm load cells
Input Noise
0.3 V p.p or less
Input Impedance
10 (Min.)
A/D converter
24bit Sigma-Delta system
A/D internal resolution
Approximately 200,000 counts
A/D sampling speed
50 times/sec
2. Digital Part
Display
7 Segment LED,
5-Digits, 14.1mm(Height)
Display below zero
-minus signal
Display speed
50 times/sec ~ 1 times/sec
Additional symbols
Hold, Zero, Stable,

Relay point(LO, OK, HI)
Min. Division
1, 2, 5, 10, 20, 50, 100, 200 selectable
Decimal Point
0, 0.0, 0.00, 0.000
5
3. Technical
AC adapter
AC 110, 220V 10%, 50/60Hz
Power consumption
10 VA
Data Memory
10 year
Operating temperature
-10~+50
Humidity
85% Rh Max.
Overall dimensions
96(W) x 48(H) x 136(D)
Weight
530 g
4. Option
Standard
Relay 3CH Output
Option 1
Serial Interface : RS-232C
Option 2
Serial Interface : RS-422
Option 3
Serial Interface : RS-485
Option 4
Analog Output : DC 0 ~10 V
Option 5
Analog Output : DC 4 ~20 mA
Example) Option 4 : Relay 3CH + DC 0 ~ 10V
6
Dimensions
96
High Precision DIGITAL INDICATOR
BS - 205
OK
HI
HOLD
ZERO
STABLE
48
LO
M
BONGSHIN
136
119
11
92
43
91
44
Dimensions for cutting panel
To mount the BS-205 to the panel, remove its fittings and insert it through
the hole in the front of the panel. From the back of the panel, fix the
product to the panel with the fittings.
7
Front Panel
BS - 205
LO
OK
HI
HOLD
ZERO
STABLE
4
BONGSHIN
1. Display Lamp (
LO (L1) lamp : It will lamp when 1step control works.

Indicates the result of judgment and turns on
if the measured value < LO judgment value.
OK (L2) lamp : It will lamp when 2step control works.
if LO judgment value the measured value
HI judgment value.
HI (L3) lamp : It will lamp when 3step control works.
if the measured value > HI judgment value.
HOLD lamp : Lamp is on when moving object is weighed.
Turns on if peak hold/ instant hold is on.
ZERO lamp : ON when the current weight is 0 kg.
Turns on if digital zero is on.
STABLE lamp : ON when the weight is stable.
2. Keyboard
1) Pressing the increments and mode keys together changes

to the parameter setting mode.
2) Returns to the measurement mode.(ESC)
3) Selects the item to be set.
1) Holding down the increment key for about two second

moves to the peak hold & instant mode.
2) Changes the value or content of a selected digit.
(Increments the value)
1) Holding down the increment key for about one second

moves to the peak hold & instant clear mode.
2) Changes the digit to be set.
1) Store current condition and exit.

4
M
M
+
1
= Parameter setting mode

2
+
1
= Relay setting mode

3
+
4
= Digital zero function

2
+
4
= Key LOCK or Key LOCK clear mode

3
9
Rear Panel
F.G
POWER
LO (L1)
OK (L2)
HI (L3)
RELAY OUTPUT
HOLD
ZERO
SHIELD
COM1
INPUT
4
E+
E-
S+
S-
COM2
OPTION
1
F.G (GROUND) : It is a grounding terminal.

Ground it to prevent an electric shock and a trouble of
static electricity.
POWER(AC IN) :
Use a stable power supply AC110/220V 10%, 50/60Hz
- Set up voltage AC220V
Connect power supply to terminals No.13(L) and No.14(N).
Pin No.
13
POWER
14
POWER
15
F.G
Power terminal without polarity for both

DC and AC
Power terminal without polarity for both
DC and AC
Frame Ground
10
LOAD CELL :
Please connect the indicator connector with the wire of

load cell according to the color.
Pin no.
Signal name
Contents
SIG- (Blue)
Load cell output (-)
SIG+ (Green)
Load cell output (+)
EXC- (White)
Load cell Input Voltage (-)
EXC+ (Red)
Load cell Input Voltage (+)
SHIELD
Shield
The wire color of load cell according to a manufactures.
Maker
1
SIG-
2
SIG+
3
EXC-
4
EXC+
5
SHIELD
BONGSHIN
BLUE
GREEN
WHITE
RED
SHIELD
CAS, TMI, AND

BLH
INTERFACE
KYOWA
P.T.
SHOWA
SHINKOH
TML
TFAC
HUNTLEIGH
BLUE
RED
WHITE
WHITE
WHITE
BLACK
WHITE
GREEN
BLACK
WHITE
GREEN
WHITE
GREEN
GREEN
GREEN
WHITE
GREEN
WHITE
WHITE
RED
WHITE
BLACK
BLACK
BLACK
BLACK
BLUE
BLACK
BLACK
BLUE
BLACK
RED
GREEN
RED
RED
RED
RED
RED
RED
RED
GREEN
SHIELD
YELLOW
SHIELD
SHIELD
SHIELD
SHIELD
SHIELD
SHIELD
YELLOW
SHIELD
Because wire color may be different according to a manufacture and

load cell models.
Please refer for the data sheet of load cell.
Cautions 1. When connecting a six-wire type strain gage sensor, shortcircuit (EXC+ and SEN+)(EXC- and SEN-), respectively.
Cautions 2. Applied voltages to the strain gage sensor are 10.
When any sensor rated below the applied voltage is connected,
it may generate heat or be damaged
11
IN-PUT : COM1, ZERO, HOLD
This key is to control a equipment from the outside .
Please connect between COM terminal and each input terminal .
Because the power of input terminal was connected with 12V voltage
From the inside.
* An electric current is about 10mA.
* Please make the minimum time to input a data with over 50msec.
Pin No.
Name
COM1
ZERO
HOLD
Description
Common for all external control terminals.
Control for digital zero function. Enabled when
short-circuited or at the same potential as COM.
Control for hold function. Enabled when shortcircuited or at the same potential as COM.
12
RELAY OUTPUT :
COM2, HI(L3), OK(L2), LO(L1)
Connect between COM terminal and OUTPUT terminal

With the earth of no electric power.
Please use the output data For a signal only, dont use it for working.
Max earth capacity : AC250V / 0.5A
Pin No.
Name
Description
COM2
Common terminal for relay output
10
HI (L3)
HI (L3) output terminal (a, b contact)
11
OK (L2)
OK (L2) output terminal (a, b contact)
12
LO (L1)
LO (L1) output terminal (a, b contact)
13
OPTION :
Analog output (0~10V, 4~20mA) & Serial communication

(RS-232C, RS-422/485) option.
Analog output (0~10V, 4~20mA) option

Pin No.
Name
1
2
3
4
V-OUT
COM
COM
A-OUT
Description
Voltage output terminal (0 to 10V)
Common terminal for analog output.
Current output terminal (4 to 20mA)
Serial output (RS-232C) option

Pin No.
Name
Description
1
2
3
4
RX
TX
SG
NC
RS-232C reception
RS-232C transmission
Common terminal for communications
Do not connect this terminal
Serial output (RS-422) option

Pin No.
Name
1
2
3
4
RXD (-)
RXD (+)
TXD (-)
TXD (+)
Description
RS-422
RS-422
RS-422
RS-422
RX(-)
RX(+)
TX(-)
TX(+)

Pin No.
Name
1
2
3
4
NC
NC
TXD (-)
TXD (+)
Description
RS-485
RS-485
14
TERMINAL BLOCK
AC Voltage change
Available to change AC110/220V with multiple.
Before setting up, please confirm the power voltage.
Please change the connect terminal of 110V/220V after opening the
cover. If you need to change. (It was setted with AC220V at the first)
15
AC 220V change
AC 110V change
16
Information on Each Parameter
Indication
Name
Calibration data
Load cell
LC.CAL Rated output
set
Maximum
SCALE
Capacity set
Span weight
At.CAL
set
Function data
biP
Display Mode
Setup options
Default
value
1 mV/V ~3 mV/V
2.0000
0~99999
10000
0~99999
20000
biP (+/- display)/ uniP (+ display)
biP
Decimal
0(0)/1(0.0)/2(0.00)/3(0.000)/4(0.0000)
2
Point set
Minimum
ds.1
1/ 2/ 5/ 10/ 20/ 50/ 100/ 200 digit
1
Division set
Number of
average
dU.2
1/ 2/ 5/ 10/ 25/ 50
2
operations
setup
Zero
Zt.oFF
OFF/ON
OFF
Tracking set
Auto zero
AZ.oFF
OFF/ON
OFF
backup set
Hold function OFF(No used)
Hd.oFF
OFF
set
/P(Peak Hold)/ I(Instant Hold)
Manual Tare
tare
0~99999
00000
weight set
Condition data (Serial interface option)
Equipment
Id.0
0 ~15
0
ID setup
Baud rate
1200/2400/4800/9600/1920(19200)/
r.9600
9600
setup
3840(38400)
CommunicaRc.on
ON(Data is required)/OFF(Stream mode) ON
tion mode
dP.2
Condition data (Analog output option)

dA.LO
Analog
output LO
indication
setup
0~99999
00000
17
dA.HI
Analog
output HI
indication
setup
Indication
Name
0~99999
10000
Setup options
Default
value
Comparator data
rLY.1H
rLY.1L
r1H.on
rLY.2H
rLY.2L
r2H.on
rLY.3H
rLY.3L
r3H.on
L1 HI side
judgment
value setup
L1 LO side
judgment
value setup
L1 Relay
motion mode
L2 HI side
judgment
value setup
L2 LO side
judgment
value setup
L2 Relay
motion mode
L3 HI side
judgment
value setup
L3 LO side
judgment
value setup
L3 Relay
motion mode
-9999 ~ 99999
10000
-9999 ~ 99999
10000
r1H.on /r1L.on/ r1r.on
r1H.on
-9999 ~ 99999
9999
-9999 ~ 99999
5001
r2H.on
-9999 ~ 99999
5000
-9999 ~ 99999
5000
r3H.on
18
1. Calibration data
1-1 Load cell rated output set (LC.CAL)
Set the rated output value(mV/V value) for the strain gauge sensor.
The setting rage of the rated output value for strain gauge sensor is 0.1 to
3.0 mV/V.
1-2 Maximum Capacity set (SCALE)
Set the indicated value when the rated output value is acquired and
finalized.
Setting range of SCALE set value (indicated value) 100 to 99999.
Acquire both load cell rated output set value and measured value (SCALE
value) and finalize with ENTER key.
1-3 Span weight set (At.CAL)
Actual load is performed by applying actual load to the connected strain
gauge sensor, and by setting the indicated value (SPAN set value) at the
time.
Setting range of SCALE set value (indicated value) 100 to 99999.
Resolution in this meter is 20000 at the time of a 2.0000 mV/V value.
2. Function data
2-1 Display mode (biP)
biP +/- display, uniP + display,
2-2 Decimal point set (dP.2)
Set the decimal point position displayed on the set-value select screen.
Setting items : 0(0), 1(0.0), 2(0.00), 3(0.000), 4(0.0000)
2-3 Minimum Division set (ds.1)
Set the minimum updating width of indicated values.
Set it on the set-value select screen.
Setup items : 1, 2, 5, 10, 20, 50, 100, 200
2-4 Average operations setup
(dU.2)
This function is provided for the moving average of data after A/D
conversion so as to reduce the fluctuation of the indicated values.
As the number of times of moving average is increased, the indicated
value is stabilized. However response becomes slow.
Set it on the set-value select screen.

Setup items : 1, ,2, 5, 10, 25, 50
19
2-5 Zero Tracking set (Zt.oFF)

This function is provided to correct automatically the slow change of the
zero point due to a change in the environment etc.
When the indicated value is below the ZT width, the indicated value is set
to 0 and internal correction is performed at every ZT cycle.
2-6 Auto ZERO backup set (AZ.oFF)
ON/OFF setting can be performed by pressing by pressing the
increment key one at a time.
When backup is set to OFF, Digital ZERO continues even when power is
turned OFF/ON.
2-7 HOLD Function set (Hd.oFF)
This function is provided to detect one sample with a peak, instant hold,
and point of inflection, holds the indicated value, performs HI/OK/LO limit
comparison simultaneously, and outputs the result.
Turning on Hold control terminal signal with both HOLD key turned on
will not be accepted. Priority is given to HOLD key.
Peak HOLD :
The peak hold function retains one of the maximum values and provides
output for that value. Selection from these values is made using the hold
function data.
Instant HOLD :
The Hold function temporarily retains the indication.
2-8 Manual TARE Weight set (tare)
The purpose of using tare is to subtract a certain weight on the real
weight.
When you already know the tare weight, press key tare and input tare
weight with arrow keys and memorize it by pressing ENTER key.
Setting range of TARE set value (indicated value) 99999.
3. Condition data (Serial Interface option)

3-1 Equipment ID setup (Id.0)
The ID is necessarily required to connect several indicators to control
together with a host PC.
Setting range : 0 to 15
20
3-2 Baud rate setup (r.9600)
To enable the communication mode, proper baud rate should be set
within r1200~r3840, in which r1920 means 19200bps and r3840 means
38400bps.
Setup items : 1200, 2400, 4800, 9600, 1920(19200), 3840(38400)
3-3 Communication mode setup (Rc.on)
Rc on : Transmit when data is required
Rc oFF : Stream mode
Serial communication protocol.
4. Condition data (Analog output option)

4-1 Analog output LO indication setup (dA.LO)
Set an indicated value when analog output is 0V or 4mA.
4-2 Analog output HI indication setup (dA.HI)
21
ZERO Calibration
The digital zero function zeros the indication given at an arbitrary timing.
Thereafter, the function shows the amount of change from the point of
zeroing. However, this function serves as an indication resetting function for
a frequency measuring unit. Thus, the digital zero function can be used to
reset the indication when there is no input signal at all.
Note that, the on/off control of the digital zero function can be achieved by
means of terminal control or front panel keys. In the case of terminal control,
the digital zero function is turned on by short circuiting the ZERO and COM1
terminals or setting both terminals to the same voltage level. The indication
at that moment is zeroed. In the case of control with the front panel keys,
hold down the enter key and press the increment for about 1 second to zero
the indication at that moment.
1. Method of Setting zero

Pressing the
key while pressing the
key
2
and zero set mode.
Note : The setup condition are protect clear.

If these conditions are not satisfied, an error indication appears
and the display returns.
2. Digital ZERO Backup

Function data
AZ.oFF
Auto zero
backup set
OFF/ON
OFF
ON/OFF setting can be performed by pressing by pressing the increment

key one at a time.
When backup is set to OFF, Digital ZERO continues even when power is
turned OFF/ON.
22
Actual Load Calibration
Actual load calibration means that calibration is carried out by applying
actually measured pressure to a sensor such as a load cell connected to
the meter.
1. Method of setting
Pressing the

1
and actual load calibration mode. (CAL MODE)
2. Calibration Manu (CAL 1 ~ CAL 5)
CAL 1 : Zero Calibration

CAL 2 : Rated Output set
CAL 3 : Maximum Capacity set
CAL 4 : Setting Weight & Span Calibration
CAL 5 : End
key
2
23
Press the increment key, and enter key

together during measurement.
(Digital zero)
Press the increment key, and mode key
Press the enter change to the equivalent

calibration mode.
Press the shift key (change digit) and
increment key (change numeric value) to
set load cell rated output. (specifications)
(example : 2mV/V)
Press the enter key to move to the
maximum capacity mode.
Press the enter key. Press the shift key
(change digit) and increment key (change
numeric value) to set load cell maximum
capacity. (specifications)
(example : 10000kg)
Press the enter key to move to the span
calibration mode.
Press the enter key to change to the
span indicating value setup mode.
set 20000.
function data mode.
Press mode or enter key to return to the
measurement mode.
24
Equivalent Calibration
Equivalent calibration means that calibration is carried out according to the
ratings (specifications) of such a sensor as a load cell. It is not necessary
to connect the sensor or to apply pressure to the sensor. Set the rated
value for the strain gauge sensor and the indicated value at the time.
Equivalent calibration can be performed only by setting the rated
output(mV/V) of the strain gauge sensor and the indicated value at the time,
without actual load.
Pressing the

1
and equivalent calibration mode. (CAL MODE)
2. Calibration Manu (CAL 1 ~ CAL 4)
CAL 1 : Zero Calibration

CAL 2 : Rated Output set
CAL 3 : Maximum Capacity set
CAL 4 : End
key
2
25
Press the increment key, and enter key

together measurement. (Digital zero)
Press the increment key, and mode key
Press the enter change to the equivalent

calibration mode.
set load cell rated output. (specifications)
(example : 2mV/V)
maximum capacity mode.
numeric value) to set load cell maximum
capacity. (specifications)
(example : 10000kg)
Press the enter key to move to the span
calibration mode.
Press mode key to return to the
measurement mode.
Press not enter key.
26
Comparator Data (Relay setting)
Pressing the

1
key
3
and equivalent calibration mode. (Comparator MODE)
2. Calibration Manu
3. Output Specifications
Conditions for comparison
Indicated value
> Upper limit judgment value
Judgment result
HI
Lower limit judgment value Indicated value

Upper limit judgment value
OK
Lower limit judgment value > Indicated value
LO
27
4. Method of Setting Comparator Data (L1 ~ L3)
M
Press the shift key, and mode key

Press the enter key to change to the relay 1
High setup mode.
increment key (change numeric value) to set
relay 1 High output. (example : 10000)
Press the enter key to move to the relay 1 Low
setup mode.
numeric value) to set relay 1 Low.
Press the enter key to move to the relay mode.
Press increment key a few times set the relay

mode.
Press the enter key to change to the relay 2
High setup mode.
The same method applies to other parameters.
.
3
28
4
29
Indication
Setup options
Relay mode (r1H.on /r1L.on/ r1r.on)

The r1H.on mode means the relay 1 motion mode, in which
the load within the limits will activate a relay on and the load
beyond the limits will activate a relay off.
Weight
Relay OFF
Relay ON
r1H.on
Relay 1 Hi
Relay 1 LO
Time
The r1L.on mode means the relay 1 motion mode, in which

the load within the limits will activate a relay off and the
load beyond the limits will activate a relay on.
Weight
Relay OFF
Relay ON
r1L.on
Relay 1 Hi
Relay 1 LO
Time
The r1r.on mode means the range mode, in which the load
within the limits will activate a relay on and the load beyond
the limits will activate LO LED on as a warning of high NG or
low NG.
Weight
r1r.on
Relay OFF
Relay ON
Relay 1 Hi
Relay 1 LO
Time
The same method applies to other parameters.
30
5. Relay Motion Mode
5-1 HI ON relay motion mode : r1H.on, r2H.on, r3H.on
: The load within the limits will activate a relay ON.
Weight
L3 ON
L3 Hi value
[ HI ]
L3 Lo value
L3 OFF
L2 ON
L2 Hi value
[ OK ]
L2 Lo value
L2 OFF
L1 Hi value
[ LO ]
L1 ON
L1 Lo value
L1 OFF
0
Time
OFF
ON
OFF
OFF
ON
OFF
OFF
ON
OFF
LO (L1) Relay Output

OK (L2) Relay Output
HI (L3) Relay Output
Example 1)
rLY.1H
rLY.1L
HI ON
mode
rLY.2H
rLY.2L
rLY.3H
rLY.3L
L1 HI side
judgment value
L1 LO side
judgment value
L2 HI side
judgment value
L2 LO side
judgment value
L3 HI side
judgment value
L3 LO side
judgment value
1000 within the limits

will activate a relay ON
900 beyond the limits
900
(or 1000) will activate a relay OFF
1000

1900
2000

2900
3000
31
5-2 LO ON relay motion mode : r1L.on, r2L.on, r3L.on
: The load within the limits will activate a relay OFF.
Weight
L3 OFF
L3 Hi value
[ HI ]
L3 Lo value
L3 ON
L2 OFF
L2 Hi value
[ OK ]
L2 Lo value
L2 ON
L1 Hi value
[ LO ]
L1 OFF
L1 Lo value
L1 ON
0
Time
ON
OFF
ON
ON
OFF
ON
ON
OFF
ON

Example 1)
rLY.1H
rLY.1L
LO ON
mode
rLY.2H
rLY.2L
rLY.3H
rLY.3L
L1 HI side
judgment value
L1 LO side
judgment value
L2 HI side
judgment value
L2 LO side
judgment value
L3 HI side
judgment value
L3 LO side
judgment value
1000
900
2000
1900
3000
2900

will activate a relay OFF
32
5-3 Range ON relay motion mode : r1r.on, r2r.on, r3r.on
: Indicates the result of judgment and turns on
if LO judgment value the measured value Hi judgment value.
Weight
L3 OFF
L3 Hi value
[ HI ]
L3 ON
L3 ON
L3 Lo value
L3 OFF
L2 OFF
L2 Hi value
[ OK ]
L2 ON
L2 ON
L2 Lo value
L2 OFF
L1 Hi value
[ LO ]
L1 Lo value
L1 OFF
L1 ON
L1 ON
L1 OFF
0
Time
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF

Example 1).
rLY.1H
L1 HI side
judgment value
1000
rLY.1L
L1 LO side
judgment value
900
rLY.2H
L2 HI side
judgment value
2000
rLY.2L
L2 LO side
judgment value
1900
rLY.3H
L3 HI side
judgment value
3000
rLY.3L
L3 LO side
judgment value
2900
Range
mode

33
5-4 Comparator weighing mode : r1L.on, r2r.on, r3H.on
: Indicates the result of judgment and turns on
if L1 judgment value L2 judgment value L3 judgment value.
Weight
[ HI ]
L2 OFF
L3 Hi, Lo value
L2 Hi value
L2 ON
[ OK ]
L2 Lo value
L1 Hi, Lo value
L2 ON
[ LO ]
L2 OFF
Time
ON
OFF
ON

OFF
ON
OFF
ON
OFF

OFF
ON
OFF
Example 1)
L1
LO ON
mode
L2Range
mode
L3
HI ON
mode
rLY.1H
rLY.1L
L1 HI side
judgment value
L1 LO side
judgment value
1000
1000
rLY.2H
L2 HI side
judgment value
3000
rLY.2L
L2 LO side
judgment value
1000
rLY.3H
L3 HI side
judgment value
3000
rLY.3L
L3 LO side
judgment value
3000

In the range of
relay ON
34
Hold Function
1. Hold Function
The Hold function temporarily retains the indication. The hold function is
enabled by short circuiting the HOLD and COM terminals or setting both
terminals to the same voltage level. As a result the display unit retains the
indication given at that moment.
Hold function
set
Hd.oFF
OFF(No used)
/P(Peak Hold)/ I(Instant Hold)
OFF
Method of setting Hold data
Press the increment and mode keys together during

measurement.
Press the mode key a nine times to display the hold
mode data menu. Press the increment key a few times
to display the parameter to be set. Press the enter key
to set. Press the enter or mode key to the
measurement mode.
Indication
Setup options
HOLD mode (Hd.oFF / Hold.P/ Hold.I)

BS - 205
LO
OK
HI
HOLD
ZERO
STABLE
No used (Hold off)

M
4
BONGSHIN
- Peak HOLD The peak hold function retains one of the maximum
values and provides output for that value. Selection
from these values is made using the hold function
data.
BS - 205
LO
OK
HI
HOLD
ZERO
STABLE
4
BONGSHIN
35
- Instant HOLD The Hold function temporarily retains the indication.
BS - 205
LO
OK
HI
HOLD
ZERO
STABLE
4
BONGSHIN
2. Method of Setting Hold

KEY HOLD
Press the Increment key for about 1.5 second.
2
External HOLD Controls

The hold function is enabled by short circuiting the HOLD
and COM1 terminals or setting both terminals to the same
voltage level.
The hold function is not disabled if the control terminal are made to
go through the on-off-on sequence with the function enabled by
means of the front panel keys.
3. Method of Setting Hold clear

KEY HOLD Clear
Press shift key.
3
External HOLD Clear Controls

The hold function is enabled by short circuiting the HOLD
and COM1 terminals or setting both terminals to the same
voltage level.
36
KEY Lock or KEY Lock clear
1. Method of Setting KEY Lock
Press the shift key and enter keys together during measurement.
Protect others.
BS - 205
LO
OK
HI
HOLD
ZERO
STABLE
4
BONGSHIN
2. Method of Setting KEY Lock clear
Press the shift key and enter keys together during measurement.
BS - 205
LO
OK
HI
HOLD
ZERO
STABLE
4
BONGSHIN
37
Option
1. RS-232C Serial Interface (Option-1)
OPTION
1
Pin No.
Name
Description
1
2
3
4
RXD
TXD
SG
NC
RS-232C reception
RS-232C transmission
Common terminal for communications
Function
Equipment
Id.0
0 ~15
0
ID setup
Baud rate
1200/2400/4800/9600/1920(19200)/
r.9600
9600
setup
3840(38400)
CommunicaRc.on
ON(Data is required)/OFF(Stream mode) ON
tion mode
Signal Format
Type
Method :
EIA-RS-232C
Full-Duplex , Asynchronous, Bi-direction
Baud rate : 1200, 2400, 4800, 9600, 19200, 38400bps ( Baud-Rate )

Format :
Data Bit
Start/Stop
Parity Bit
Code
:
:
:
:
8 (NO Parity)
1 bit
Even or Odd
ASCII
38
Serial Communication Protocol
The below describe an example on the settings for communication
between an indicator and a PC assuming that current display is 32.567
and the ID of a indicator is 5.
1) Transfer the current display from host PC
Byte 1 (Indicator ID)
35H
Byte 2
R(52H)
Response from Indicator

Byte 1
STX(02H)
Byte 7
5(35H)
Byte 2
35H
Byte 8
6(36H)
Byte 3
+(2BH)
Byte 9
7(37H)
Byte 4
3(33H)
Byte 10
ETX(03H)
Byte 5
2(32H)
Byte 6
.(2EH)
2) Special Functions Set
Auto Zero set

Hold set
Hold clear set
Host (PC)
35H
35H
35H
Indicator
Byte 2
Z(5AH)
Byte 2
H(48H)
Byte 2
L(4CH)
Example) 1(ID)+07.487
ASCII
HEXA
1+07.487
02 31 2B 30 37 2E 34 38 37 03
Example) 1(ID)+07487
ASCII
HEXA
1+07487
02 31 2B 30 37 34 38 37 03
Example) 15(ID)+07486
ASCII
HEXA
15+07486
02 3F 2B 30 37 34 38 36 03
Example) 2(ID)+074.86
ASCII
HEXA
2+074.86
02 32 2B 30 37 34 2E 38 36 03
No response
Transfer again
to enable
Transfer again
to disable
39
Connection of RS-232C
RXD
Transmit Data
TXD
Receive Data
GND
Chassis Ground
Carrier Detect
Data Terminal Ready
Data Set Ready
Request to Send
Clear to Send
RS-232C port of
BS-205
9 pin serial port of

computer
RXD
Transmit Data
TXD
Receive Data
GND
Signal Ground
Request to Send
Clear to Send
Data Set Ready
Carrier Detect
20
RS-232C port of
BS-205
Data Terminal Ready
25 pin serial port

of computer
40
2. RS-422/485 Serial Interface (Option-2)
-
RS-422 is to transmit the signal by the power difference.

Also, it is more safety rather other interface system for a electric noise.
- Specially please use the cable with shield coax cable surely.
- Recommended distance is under 1.2 km.
- Both end side of a wire must be connected by the termination of
300.
Signal Format : Same as RS-232C
Data Format : Same as RS-232C
Connecting method of RS-422/485 port

OPTION
1

Pin No.
Name
1
2
3
4
RX (-)
RX (+)
TX (-)
TX (+)
Description
RS-422
RS-422
RS-422
RS-422
RX(-)
RX(+)
TX(-)
TX(+)

Pin No.
Name
1
2
3
4
NC
NC
TXD (-)
TXD (+)
Description
RS-485
RS-485
41
3. Voltage (0~10V) Analog Output (Option-03)
The BS-205 series of unit meters can output an analog signal for an indicated
value.(when the meter is equipped with an analog output unit)
The analog output of the BS-205 series allows for arbitrary output scaling.
This scaling can be achieved by setting the indication value for an output of the
maximum scale value(10V for 0~10V output range) in the dA.HI parameter of the
scaling data.
The voltage output occurs proportionally the voltage according to
the size of a weight In 0V ~10V.
OPTION
1

Pin No.
Name
1
2
3
4
V-OUT
COM
COM
A-OUT
Description
SPECIFICATION
output Voltage
0 ~ 10V DC out
Precision
Max 1/1000
Min Impedance
Over 1 k
42
BS - 205
LO
OK
HI
HOLD
ZERO
STABLE
Analog output LO
indication setup
0~99999
00000
Analog output HI
indication setup
0~99999
10000
4
BONGSHIN
BS - 205
LO
OK
HI
HOLD
ZERO
STABLE
4
BONGSHIN
1) Analog Output LO
Setting range : + 99999
2) Analog Output HI
Example of analog output setting
Set the indicated value when analog output is 0V(or 4mA) to 400.
Note 1) When the indicated value becomes larger than analog output
set value, it is not properly output.
Note 2) When the indicated value is OVER, and analog output is less than
0V, the output is near 0V.
43
4. Electric current (4~20mA) Analog
Output (Option-4)
The BS-205 series of unit meters can output an analog signal for an indicated
value.(when the meter is equipped with an analog output unit)
The analog output of the BS-205 series allows for arbitrary output scaling.
This scaling can be achieved by setting the indication value for an output of the
maximum scale value(20mA for 4~20mA output range) in the dA.HI parameter of
the scaling data.
The current output occurs proportionally the current according to
the size of a weight In 4~20mA.
OPTION
1

Pin No.
Name
1
2
3
4
V-OUT
COM
COM
A-OUT
Description
SPECIFICATION
output Voltage
Precision
Min Impedance
4 ~ 20 mA DC Current out
Max 1/1000
Under 500
44
BS - 205
LO
OK
HI
HOLD
ZERO
STABLE
Analog output LO
indication setup
0~99999
00000
Analog output HI
indication setup
0~99999
10000
4
BONGSHIN
BS - 205
LO
OK
HI
HOLD
ZERO
STABLE
4
BONGSHIN
1) Analog Output LO
2) Analog Output HI
Example of analog output setting
Note 1) When the indicated value becomes larger than analog output
set value, it is not properly output.
Note 2) When the indicated value is OVER, and analog output is less than
0mA, the output is near 0mA.
45
5. Parallel BCD Output (Option-6)
F.G
OPTION
Pin assignment and circuit
Pin No.
SIGNAL
Pin No.
SIGNAL
GROUND/ (-) COMMON
20
4 x 104
1 x 10
21
8 x 104
2 x 100
22
4 x 10
23
8 x 10
24
Decimal Point
101
1 x 10
25
Decimal Point
102
2 x 101
26
Decimal Point
103
4 x 101
27
Decimal Point
104
8 x 10
28
10
1 x 102
29
11
2 x 10
30
12
4 x 10
31
13
8 x 102
32
14
1 x 103
33
15
2 x 10
34
16
4 x 10
35
17
8 x 103
36
ZERO (Input DC+24V)
18
1 x 10
37
ZERO (Input DC-24V)
2 x 10
19
POLAR (+/-)
BUSY
GROUND/ (-)COMMON
46
Minus common connection
Data Transfer Mode
Setting of the BCD output is done with the general functions.

Name
Equipment
Setting
ID setup
Id.0
Baud rate setup
r.9600
Communication mode
Rc.oFF
Signal Logic
1)
Weight BCD DATA Output : Negative
2)
Polarity Output : + = High
3)
BUSY : BUSY = High
Specification
1)
BCD output (NPN Open Collector Type)
2)
Standard Accessory : 37P D-Type Female connector
47
Error Message and Trouble Shooting
ERROR
CAUSE
A/S
Checking for Input,
Waving a weight
Value.
Load cell damage
Output of load cell.
Insulation
Resistance Value.
resistance
Resistance value of
Load cell.
Checking Insulation
Resistance value of
Load cell damage.
A. Changing a
Load cell.
(Normal Max 100M or
Weight value,
-OL-appear)
B. Not return to
ZERO
Confirm a connect of
Appear "no.LC"
Disconnected to
Load Cell.
Load cell
Checking a single wire
Of load cell cable
Weight (-) changed
Load cell output

(SIG+,SIG-)changed.
Load cell connector
Load cell damage Load cell damage

Connection Error
Input resistance
: about 1130
Output resistance
: about 1000
badness of load cell. Checking Insulation

Weighing part error
Reference.
Load cell connector
Appear "Ovr"
"-Ovr"
Excess Max weight Remove excess weight
Insulation
Resistance
: over100M
48
Warranty and After-service
1. Warranty
The warranty period shall be one year from the date of delivery. Any failure
that arises during this period and the cause thereof is judged to be
obviously attributable to BONGSHIN LOADCELL CO., LTD. Shall be remedied
at no cost.
2. After-service
This product is manufactured, tested, inspected, and then shipped under
stringent quality control. Should the product fail, however, contact (or send
the product to) your vendor or BONGSHIN LOADCELL directly.
(It is advisable that you send a memo describing the failure in as much
detail as possible along with the product returned.)
(462-120) 148 Sangdaewon-dong, Jungwon-gu,

Seongnam-si Gyeonggi-do, KOREA
TEL : 82-31-742-6661 FAX : 82-31-742-6664
http://www.bongshin.com loadcell@bongshin.com

Bs 205 0512e

Uploaded by

Copyright:

Available Formats

Bs 205 0512e

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Bs 205 0512e

Uploaded by

Copyright:

Available Formats

1

The Features of BS-205 . .

Actual Load Calibration

Place the indicator on a flat and stable surface.

Applying voltage and current exceeding the maximum permissible

Do not subject the scale to sudden temperature changes.

Do not use inflammable materials in cleaning.

The contents of this manual are subject to change without notice

Appropriate for weight and measurement system.

24 bit Sigma-Delta A/D converter for high accuracy.

Simple full digital calibration.

Simulative (mV/V memory) or live load calibration.

Watchdog circuitry (system restoration)

3 Set point relay output.

Hold, peak hold and auto zero.

Option serial output or analog output.

0.01% F.S. max.

Max. Display resolution

Min. Input sensitivity

Zero : 0.1 V/ RTI max.

Load cell excitation

up to 4 x 350 ohm load cells

0.3 V p.p or less

24bit Sigma-Delta system

A/D internal resolution

Approximately 200,000 counts

A/D sampling speed

Display below zero

Hold, Zero, Stable,

1, 2, 5, 10, 20, 50, 100, 200 selectable

0, 0.0, 0.00, 0.000

AC 110, 220V 10%, 50/60Hz

96(W) x 48(H) x 136(D)

Relay 3CH Output

Serial Interface : RS-232C

Serial Interface : RS-422

Serial Interface : RS-485

Analog Output : DC 0 ~10 V

Analog Output : DC 4 ~20 mA

Example) Option 4 : Relay 3CH + DC 0 ~ 10V

Dimensions for cutting panel

LO (L1) lamp : It will lamp when 1step control works.

1) Pressing the increments and mode keys together changes

1) Holding down the increment key for about two second

1) Holding down the increment key for about one second

1) Store current condition and exit.

= Parameter setting mode

= Relay setting mode

= Digital zero function

= Key LOCK or Key LOCK clear mode

F.G (GROUND) : It is a grounding terminal.

Power terminal without polarity for both

Please connect the indicator connector with the wire of

Load cell output (-)

Load cell output (+)

Load cell Input Voltage (-)

Load cell Input Voltage (+)

The wire color of load cell according to a manufactures.