CHAPTER 1

INTRODUCTION

JIF-2002 WEIGHING INDICATOR&CONTROLLER

1
1-1 Welcome
The JIF-2002 weighing indicator is a model of breakthrough
high resolution. With set-point codes, this model makes batching
control an easy task. With relatively compact size, JIF-2002
performs a remarkable accuracy and speed.
With sincere gratitude for your using our products, once any
question or problems occurred, please contact us immediately
for further services.

1-2 Features
JIF-2002 Weighing Indicator & Controller Features:

1/16,000 display resolution (Max. 1/ 60,000 depending on load

cell quality & performance).
Internal Resolution 1,000,000, A/D Conversion rate 120 times/
Sec.
Watchdog virtually eliminates malfunctions that associated
with computerized equipment or software failure.
Full Digital Calibration makes setting ZERO and SPAN
Calibration an easy task.
Drives up to 8 parallel connecting load cells.
8k bytes SRAM with Li-battery backup.
Information will not disappear even power failure.
The settings of function and weighing parameters are all
stored in the EEPROM, with storage duration over 40 years.
Important values and parameters can have storage backup.
Users can adjust the intensity of digits filter to avoid
mechanical vibration that caused by external environments
to achieve high-speed and accurate measurement.
Set point codes can store up to 100 sets of Final, SP1, SP2,

Free Fall, HI, LO.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

2
Automatic Free Fall Compensation provides closer tolerance
and precise weighing.
8 Set of control Input:
ZERO Input, TARE Input, Tare reset, Start batch,
Abort batch, Print Accumulator, Print Input,
Clear
ACC. & COUNT.
8 Set of control Output:
ZERO Band output, SP1 output, SP2 Output,
(Final-Free Fall) output, HI output, LO output,
Final Output, MD/Error output.
5 batching modes:
Customer Programmed Control Mode: Normal Batching,
Customer Programmed Control Mode: Loss-in-weight
Batching,
Built-in Automatic Program Mode: Normal Batching,
Built-in Automatic Program Mode: Loss-in-weight Batching,
Multiple-Ingredient Batching.
Standard Serial Output (20mA Current Loop) for remote
display.
Optional printer interface can automatically print or output data includes
date, time, set point code, serial number, weight, and unit.
Optional:
OP-01 I/O Interface
OP-02 RS-232 or RS422/485
OP-03 Printer Interface
OP-04 Binary Coded Decimal
OP-05 Analog Output 4 20 mA
OP-06 Analog Output 0 10 V

JIF-2002 WEIGHING INDICATOR&CONTROLLER

3
1-3 System Function Introduction
SYSTEM CHECK :
CHECK DISPLAY
CHECK SARM, EEPROM
CHECK INPUT, CODE
CHECK OUTPUT
CHECK KEY

SETTING FUNCTIONS:
SETTING GENERAL FUNCTIONS (F0XX, FCXX)
SETTING CONTROLS (F1XX)
SETTING SERIAL INTERFACE (F2XX)
SETTING PRINTER (F3XX)
PARAELLE OUTPUT (BCD) (F4XX)
ANALOGE OUTPUT (F5XX) (420 mA , 010 V)

CALIBRATION:
CAL
Setting Minimum Division
Setting Decimal
Setting Maximum Capacity
ZERO Adjust
SPAN Adjust

KEY LOCK:
Disable unimportant or useless keys.

SYSTEM PARAMETER BACKUP:

JIF-2002 another copy of preset parameters.

SYSTEM PARAMETER RESTORATION:

Restore preset parameters.

SYSTEM INITIALIZE:
Re-install resets the JIF-2002 to the initial factory setting and starts the
operation.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

4
CHAPTER 2
INSTALLATION

JIF-2002 WEIGHING INDICATOR&CONTROLLER

5
2-1 Best Conditions For Use
When installing and wire connecting on JIF-2002, please follow the
points and guide for preventing any abnormal situation occurred.

Before connecting the Electric Power Supply, please identify

the input Electric voltage type is AC 110V or AC 220V.
The Grounding Wire shall be properly connected .
The Operation Temperature shall range within 0 ~ 45 ,
please DO not install in any place of direct sun-light.
Due to the minute output signal from Load Cell, please use
isolated cables. Also, separate the Load Cell cable from the
power supply cable and control I/O cables.
The input power shall be AC 110V or AC 220V10%, if the

Electric Power Supply is not stable or the interference signal

exists, that may cause uncertain actuation or reaction, even
damages .

Therefore, please utilize Electric Power Supply Stabilizer of

adequate capacity.

2-2 Power Supply Connecting

Open the case, there is a jumperS1near the transformer, please insert
a short-circuit pin to the available side.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

6
2-3 Connecting the Load Cell
Do not plug in your power cable until you have completely connected the
load cell.

Screw Signal
1 Positive Excitation Voltage, (EXC+)
2 Positive Sense Voltage, (SEN+)
3 Negative Sense Voltage, (SEN-)
4 Negative Excitation Voltage, (EXC-)
5 Positive Signal Voltage, (SIG+)
6 Negative Signal Voltage, (SIG-)
7 Shield, (SHD)

LTo connect your load cell to the weighing Indicator use a six-wire cable
with shield-connect the wires as indicated above. If the JIF-2002 is located
near the Load Cells (Within five meters or a few yards) you may use a
4-wire cable with shield, but first connect screws 1&2 and 3&4 with
independent jumper leads.

LThe analogue output from the Load Cell and input/output signals are
sensitive to electrical noise. Do not bind these cables together as it could
result in cross-talk interface. Please also keep them away from AC power
cables.
It could be dangerous by using improper battery or wrong connection of
battery.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

7
2-4 Front and Rear Panel Dimensions

Front Panel

Rear Panel

Side View

For Mounting

JIF-2002 WEIGHING INDICATOR&CONTROLLER

8
CHAPTER 3
SPECIFICATIONS

JIF-2002 WEIGHING INDICATOR&CONTROLLER

9
3-1 Analog Input and A/D Conversion
Analog Input and A/D Conversion
Type JIF-2002
Input Sensitivity 0.3uV/D
ZERO Adjustment
0 ~20mV
Range
DC10V1%230mA, Remote Sensing.
Load Cell Excitation
Can be connected up to 8 350Load Cells
Non-Linearity 0.01 % F.S.
A/D Conversion Method
A/D Resolution 1/1,000,000
A/D Conversion Rate Approx. 120 TimesSec.
Max. Load Cell Input
32mV
Voltage
ZERO Temperature (0.2V + 0.001% of Dead Load)/
Comp.
TYP
SPAN Temperature
0.001% TYP
Comp.
Max. Resolution 1/16,000 (JIF-2002 Resolution can reach
1/60,000 depending on load cell quality &
performance).

3-2 General
General
Type JIF-2002
Power Requirements AC 110V or AC 220V 10%
5060Hz, Approx. 17VA
Net weight Approx. 3.2 kg7.054 lb
Operation Temperature 10 45
Maximum Humidity 85%non-condensing
Physical Dimensions 240 (D) 190 (W) 104(H) mm

JIF-2002 WEIGHING INDICATOR&CONTROLLER

10
3-3 Front Panel Description

DIGITAL SECTION
Main Display 7-segment7-digit display, VFD screen with a
[Green Tube] 13mm character size, displays the weight.
Minimum Division 125102050
Maximum Display +800450
Under ZERO Indicator minus sign
ZEROAnnunciator Center of Zero
MDAnnunciator Motion Detected = Unstable
GROSSAnnunciator Gross Weight displayed
NETAnnunciator Net Weight displayed
TARE ENTERED Tare has been entered
Annunciator
Annunciator Status Annunciator
kg Annunciator Kilograms Displayed
lb AnnunciatorPonds Displayed
ZERO Key Stable ZEROLeft shift key
TAREKey TAREs when stable-in Net, display ZERO
Increase the number
GROSSNETKey Changes from Gross to Net and vise versa
Decrease the number
TARE CLEARKey Tare is clearedRight shift Key
PRINTACCKey Print data will send one timePrint
Accumulation
ACCCLEARKey Display AccumulatorClear Accumulation
SET POINTCODEKey Setting set point values/ Change set point code
FnKey Unused
MODEKey Change ModeEnter Key
STANDBYESC Key Standby StatusLeave the current status

JIF-2002 WEIGHING INDICATOR&CONTROLLER

11
3-4 Quick Function Table
WEIGHT FUNCTION TABLE
Decimal Point 0No Decimal 11 Decimal 22 Decimal
F 000
Adjustment 3 Decimal 44 Decimal
Weighing Unit
F 001 0None Kilogram 2Pound
Selection
Display 110 times/Sec 20 times/Sec
F 002
Update rate 340 times/Sec
F 003 Digital Filter 0 7 step digital filter
Set Zero
F 004 15% 10% 320% 430% of Max. Capacity
Range
Motion
F 005 0.5 SEC 1 DIV1 SEC 18 DIV 16 Steps (00 Stable)
Detection
Automatic
ZERO
F 006 1 SEC 0.5 DIV2 SEC 4.0 DIV 16 Steps (00 OFF)
Tracking
Compensation
ZERO &
ZERO & TARE keys always work 1only work
F 007 TARE keys
when display is STABLE
Availability
TARE Key TARE key always work 1If the GROSS is
F 008
Availability Negative (-), TARE key does not work
0OFF 1Stable 2Manual
Accumulation
F 009 Control Input Command Accumulation
Availability

20 mA Current Loop STANDARD

Same as display 2Gross Weight
F C00 Data type 3NET Weight 4TARE Weight
5Gross Weight, NET Weight, TARE Weight
Stream 2 Stable and auto print 3Manual print
F C01 Output Mode
mode4Accumulate and print
Sending without set point Code
F C02 Output Format
1Sending with set point Code

JIF-2002 WEIGHING INDICATOR&CONTROLLER

12
 Batch Weighing
F 100 Zero Band 6 digit Zero band value (Initial 000.000)
Customer Programmed Control Mode :
Batching Normal Batching Loss-in-Weight Batching
F 101
Mode Built-in Automatic Program Mode :
Normal Batching Loss-in-Weight Batching
Timer-Compar
F 102 Set between 0.0 to 2.0 Sec (Initial 0.0 Sec)
ator Inhibitor
Timer-Finish
F 103 Set between 0.0 to 9.9 Sec (Initial 0.0 Sec)
Signal
Pulse Width of
F 104 Set between 0.0 to 2.0 Sec (Initial 0.5 Sec)
Finish Signal
F 105 COM 8 Unstable 1Error
F 106 Input Mode Panel key 2 BCD Input 3 Serial Input
Please enter 6 digit free fall compensation value
Free Fall
F 107 within effective range
compensation
(Initial 000.000---Free Fall OFF)

SERIAL RS-232 OP- 02

F 200 Baud Rate 11200 BPS 2400 BPS 34800 BPS 49600 BPS
F 201 Parity 0 Non-parity Even Parity 2Odd Parity
Same as display 2Gross Weight 3NET Weight
F 202 Output Data 4TARE Weight 5Gross Weight, NET Weight, TARE
Weight
Stream 2 Stable and auto print 3Manual Print
F 203 Output Mode
Mode 4Accumulate and Print 5 Command Mode
Sending without Set point Code 1Sending with
F 204 Output Format
set point Code

PRINTER OP-03
Setting Date, Setting Year. Month, day, hour, minute, second
F 300
Time
F 301 Data Format
Not print 2Only print above the latest data
Date
3Print on all
1 Not print Only print above the latest data
Time
3Print on all

JIF-2002 WEIGHING INDICATOR&CONTROLLER

13
 Not print 2Only print above the latest data
Set
3Print on all
Serial Number Not print 1Print
Same as display 2Gross Weight
3NET Weight 4TARE Weight
Weight
5Gross Weight, NET Weight, TARE Weight
6Gross Weight, TARE Weight, NET Weight
0Not print Only print above the latest data
according to F0012Only print the latest data g
Unit
3Only print above the latest data t 4Print on all
according to F0015Print on all g 6Print on all t
1Stable and auto print Manual Print Mode
F 302 Output Mode
3Accumulate and Print
F 303 Select Printer MINI Printer 2Normal Printer

BCD OP-04
Same as display 2Gross data 3NET data
F 400 Data type
4TARE data
Stream 2 Stable and print 3Manual print
F 401 Output Mode
mode4Accumulate and print
F 402 Output Logic Positive Logic 2Negative Logic

Analog Output
Analog Output
F 500 Output 4~20 mA Output 0~+10 V
Data
F 501 Output Mode Same as display 2Gross data 3NET data
Loss-in-weight Not read Absolute Value
F 502
Absolute Value 1 BDI-2002 reads Absolute Value
Output current
F 503 when display 0.0mA through 9.99mA (Initial 0.40 mA)
ZERO
Output current
F 504 0.0mA through 9.99mA (Initial 20.0 mA)
at Full Capacity
Output Volt
F 505 when display -2.5V through +59.9V (Initial 00.0 V)
ZERO
Output Volt at -2.5V through +59.9V (Initial 10.0 V)
F 506
Full Capacity

JIF-2002 WEIGHING INDICATOR&CONTROLLER

14
3-5 Panel Key Function Table
Key Function Function Position Status
Panel Key ZERO
JIF-2002 returns to the
Pin 25 + center of ZERO if the
ZERO Control I / O
(Pin 16 or 17) weight value within F004
OP-02 range.
Z Cr Lf
Command Mode
Panel Key TARE
JIF-2002 witches to
Pin 24+ NET mode, ZEROs the
TARE Control I / O
(Pin 16 or 17) display and stores the
OP-02 TARE weight in Memory.
T Cr Lf
Command Mode
Panel Key TARE CLEAR
TARE
Pin23 + Clear TARE Value
CLEAR Control I / O
(Pin 16 or 17)
Panel Key GROSS / NET
GROSS OP-02 Shift to GROSS Mode
G Cr Lf
Command Mode
Panel Key GROSS / NET
NET OP-02 Shift to NET mode
N Cr Lf
Command Key
Panel Key PRINT / ACC
PRINT Pin19 + Print or Output latest
Control I / O Data
(Pin 16 or 17)
Panel Key PRINT / ACC
ACC Pin20 + Print Accumulator Value
Control I / O
(Pin 16 or 17)
Print Accumulator Value
ACC Panel Key ACC / CLEAR
TACC Annunciator ON
Panel Key ACC / CLEAR
Clear Accumulator and
CLEAR Pin18 +
Control I / O Count
(Pin 16 or 17)
SET
Panel Key
POINT/CODE
CODE Code Input CODE INPUT Reset Set point data
OP-02
CCXX Cr Lf
Command Key
SET Setting Final, SP1, SP2,
Panel Key
SET POINT POINT/CODE Free Fall, Hi, Lo
OP-02 S Cr Lf, SS Cr Lf

JIF-2002 WEIGHING INDICATOR&CONTROLLER

15
Key Function Function Position Status
PRINT/ACCtPRINT
ACCUMULATOR
SET POINT/CODE
Panel Key tSET POINT
ACC/CLEARtCLEAR
ACCUMULATOR
STANDBY/
Standby Mode will
STANDBY Panel Key OPERATE/
Pause all operations
ESC
STANDBY/
OPERATE Panel Key OPERATE/ Starts operation.
ESC
STANDBY/
Escape the current
ESC Panel Key OPERATE/
setting Mode
ESC
Fn Panel Key Fn Unused
Right shift key
Panel Key
while setting
Left shift key
Panel Key
while setting
Increase value
Panel Key
while setting
Decrease value
Panel Key
while setting
 Panel Key  Enter key while setting

Please refer to chapter 6 on Control I/O and OP-02

JIF-2002 WEIGHING INDICATOR&CONTROLLER

16
CHAPTER 4
SYSTEMFUNCTIONS

JIF-2002 WEIGHING INDICATOR&CONTROLLER

17
4-1 System Check
A system check should be run: after initial installation, after moving your
JIF-2002 connecting or disconnecting an attachment from the Rear Panel and
as means of locating any unexplained system error. An occasional self-check
to make sure everything is working properly is a good maintenance practice
as well.

STEP 1: Turn the Power Switch OFF on the Rear Panel.

Slide the SET switch to the set side.

STEP 2: Turn the power supply ON, the display will show blinking
SELECT.

STEP 3: Press the ZERO key and screen will show blinking CHEC,
and press key to start system check.

STEP 4: The system will check Green Tube and LED in sequence.

STEP 5: Check MEMORYEEPROMSRAM

When the screen shows SRAN, please press key. The
screen will subsequently show a series blinking dots
indicating system checking in process. If the screen shows
PASS, it means checking passed. If the screen shows FAIL,
it means system error.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

18
STEP 6: System check will go to EEPRON 1 checking.
The screen will show EE-1. Please press key and the screen
will subsequently show a series blinking dots indicating
system checking in process. If the screen shows PASS,
it means checking passed. If the screen shows FAIL,
it means system error.

STEP 7: System check will go to EEPRON 2 checking.

The screen will show EE-2. Please press key and the screen
will subsequently show a series blinking dots indicating
system checking in process. If the screen shows PASS,
it means checking passed. If the screen shows FAIL,
it means system error.

STEP 8: System check will go to BCD checking.

The screen will show CODE 00.Please make SHORT-CIRCUIT
test on 9-Pin D shape Code Input on the rear panel. When
short-circuiting COM9 with other pins, the short-circuit pin will
show the accordance value on the screen. If not, there
suggests an error occurred.

STEP 9: System check will go to Input/Output checking.

When the screen show I - O , please enter key. Subsequently,
the screen will show INPUT 0 with the 0 blinking. Please make
SHORT-CIRCUIT test on 25-Pin D shape Code Input on the
rear panel. When short-circuiting COM17 or COM16 with pin
25pin18, the short-circuit pin will light up a specific LED on
the screen. If not, there suggests an error occurred.

When short-circuiting COM17.COM16 with pin13pin16 , the

short-circuit pin will light up a specific LED on the front panel.
If two or more LED light up or turned off at the same time, there
suggests an error occurred.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

19
 STEP 10: When press a key, the key number will show in the middle of
the screen. The lower side from left to right: KEY 001KEY
008. The upper side from left to right: KEY 009KEY 010.
If the key number does not match, it suggests an error
occurred. Please contact us.

STEP 11: Finish checking, display END .

Slide the SET switch to the original side.

Above testing if any FAIL or error shows on the screen,

please contact us or distributors.

4-2 Functions
STEP 1: Turn the Power Switch OFF on the Rear Panel, Slide the SET
switch to the set side.

STEP 2: Turn the power supply ON, the display will show blinking
SELECT.

STEP 3: Press TARE key and screen will show blinking FUNC and
blinking F000 afterward.

STEP 4: Please press or key to move through the function

category (F000, F200, F300, F400 or F500). Then press the
Key to enter the category. Use the or key to choose
specific function (F000 ~ FC02, F100 ~ F107, F200 ~ 204,
F400 ~ F402 or F500 ~ F506). In each function, please use
or key to set function value. If you want to return to
previous function category, please press ESC key, or press
key to enter.

L If any errors occurred, please check if each setting value within

effective range.

L note Indicates initial factory setting.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

20
STEP 5: When you finished changing the Function setting, slide SET
Switch to the original side. The screen will show END.

General Functions

F000 Decimal Point Adjustment

0 No Decimal 1234567
1 1 Decimal 123456.7
2 2 Decimal 12345.67
3 3 Decimal 1234.567
4 4 Decimal 123.4567

F001 Weighing Unit Selection

0 None
1 Kilogram
2 Pound

F002 Display Update Rate

10 10 Times/Sec
20 20 Times/Sec
40 40 Times/Sec

F003 Digital Filter

Environmental Response
Filter
Vibration Speed
0 No stage Weak Bad Fast
1 1st stage
2 2ed stage
3 3rd stage
th
4 4 stage
th
5 5 stage
6 6th stage
7 7th stage Strong Good Slow

F004 Set ZERO Range

5 5% of weighing platform Full Capacity
10 10% of weighing platform Full Capacity
20 20% of weighing platform Full Capacity
30 30% of weighing platform Full Capacity

JIF-2002 WEIGHING INDICATOR&CONTROLLER

21
F005 Motion Detection
00 Stable
01 0.5 SEC 1 DIV
02 0.5 SEC 2 DIV
03 0.5 SEC 3 DIV
04 0.5 SEC 4 DIV
05 0.5 SEC 5 DIV
06 0.5 SEC 6 DIV
07 0.5 SEC 7 DIV
08 0.5 SEC 8 DIV
11 1 SEC 1 DIV
12 1 SEC 2 DIV
13 1 SEC 3 DIV
14 1 SEC 4 DIV
15 1 SEC 5 DIV
16 1 SEC 6 DIV
17 1 SEC 7 DIV
18 1 SEC 8 DIV

F006 Automatic ZERO Tracking Compensation

00 OFF
11 1 SEC 0.5 DIV
12 1 SEC 1.0 DIV
13 1 SEC 1.5 DIV
14 1 SEC 2.0 DIV
15 1 SEC 2.5 DIV
16 1 SEC 3.0 DIV
17 1 SEC 3.5 DIV
18 1 SEC 4.0 DIV
21 2 SEC 0.5 DIV
22 2 SEC 1.0 DIV
23 2 SEC 1.5 DIV
24 2 SEC 2.0 DIV
25 2 SEC 2.5 DIV
26 2 SEC 3.0 DIV
27 2 SEC 3.5 DIV
28 2 SEC 4.0 DIV

JIF-2002 WEIGHING INDICATOR&CONTROLLER

22
F007 ZERO & TARE keys Availability
0 ZERO & TARE keys always work
ZERO & TARE keys only work
1
when display is STABLE

F008 TARE key Availability

0 TARE key always work
If the GROSS is negative,
1
TARE key does not work

F009 Accumulation Availability

0 OFF
1 Stable
2 Manual
3 Control Input--Command Accumulation

Standard 20 mA Current Loop

FC00 Output Data

1 Same as display
2 GROSS Weight
3 NET Weight
4 TARE Weight
5 GROSS Weight, NET Weight, TARE Weight

FC01 Output Mode

1 Stream
2 Stable and auto print
3 Manual Print Mode
4 Accumulate and Print

FC02 Output Format

0 Sending without set point Code
1 Sending with set point Code

JIF-2002 WEIGHING INDICATOR&CONTROLLER

23
Batching Weighing

F000 Set ZERO Range

6 digit Zero band value ( Initial 000.000)

F101 Batching Mode

Customer Programmed Control Mode:
1
Normal Batching
Customer Programmed Control Mode:
2
Loss-in-Weight Batching
3 Built-in Automatic Program Mode: Normal Batching
Built-in Automatic Program Mode:
4
Loss-in weight Batching

F102 Timer-Comparator Inhibitor

Set between 0.0 to 2.0 Sec ( Initial 0.0 Sec)

F103 Timer-Finish Signal

The finish signal timer can be Set between 0.0 to 9.9 Sec
Initial 0.0 Sec
Finish Signal sent ON at 0.0 Sec. And stays ON until the next
START Signal

JIF-2002 WEIGHING INDICATOR&CONTROLLER

24
 F104 Pulse Width of Finish Signal
Set between 0.0 to 2.0 Sec
Initial 0.5 Sec
Stable at 0.0 Sec. which is apply to F101 setting at
3 or 4.

F105 COM 8
0 Unstable
1 Error

F106 Input Mode

1 Panel key
2 BCD Input
3 Serial Input

F107 Automatic Free Fall Compensation

Please enter 6 digit free fall compensation value within effective
range
Initial 000.000--- Free Fall OFF

SERIAL (RS-232)

F200 Band Rate

12 1200BPS
24 2400BPS
48 4800BPS
96 9600BPS

JIF-2002 WEIGHING INDICATOR&CONTROLLER

25
 F201 Parity
0 Non-parity
1 Even- Parity
2 Odd- Parity

F202 Parity
1 Same as display
2 GROSS Weight
3 NET Weight
4 TARE Weight
5 GROSS Weight, NET Weight, TARE Weight

F203 Output Mode

1 Stream
2 Stable and auto print
3 Manual Print Mode
4 Accumulate and Print
5 Command Mode

F204 Output Format

0 Sending without set point Code
1 Sending with set point Code

Printer

F300 Setting Date, Time

YY / MM / DD HHMMSS

JIF-2002 WEIGHING INDICATOR&CONTROLLER

26
F301 Data Format

Set point Serial

Date Time Weight Unit
code Number
0 Not Print Not Print Not Print Not Print Not Print
Only print
Only Print Only Print
Only Print above the
above the above the Same as
1 above the Print latest data
Latest Latest display
Latest data according to
data data
F101
Only Print
GROSS above the
2 Print on all Print on all Print on all
Weight Latest data g

Only Print
NET
3 above the
Weight
Latest data t

Print on all
TARE
4 according to
Weight
F001
GROSS
Weight,
NET
5 Print on all g
Weight,
TARE
Weight
GROSS
Weight,
NET
6 Print on all t
Weight,
TARE
Weight
Initial 1 2 1 0 1 1

JIF-2002 WEIGHING INDICATOR&CONTROLLER

27
 F302 Output Mode
1 Stable and auto print
2 Manual print mode
3 Accumulate and print

F303 Select Printer

1 MINI Printer
2 Normal Printer

BCD
F400 Data Type
1 Same as display
2 GROSS Weight
3 NET Weight
4 TARE Weight

F401 Output Mode

1 Stream
2 Stable and auto print
3 Manual Print Mode
4 Accumulate and Print

F402 Output Logic

1 Positive Logic
2 Negative Logic

Analog Output
F 500 Analog Output Data
1 Output 4~20 mA
2 Output 0~+10 V

F 501 Output Mode

1 Same as display
2 GROSS Weight
3 NET Weight

JIF-2002 WEIGHING INDICATOR&CONTROLLER

28
 F 502 Loss-in-weight Absolute Value
0 Not read Absolute Value
1 BDI-2002 reads Absolute Value

F 503 Output current when display ZERO

0.0mA through 9.99mA
Initial 4.0mA

F 504 Output current at Full Capacity

0.0mA through 9.99mA
Initial 20.0mA

F 505 Output Volt when display ZERO

-2.5V through +59.9V
Initial 00.0 V

F 506 Output Volt at Full Capacity

-2.5V through +59.9V
Initial 10.0 V

4-3 CALIBRATION
1. Select FULL CALIBRATION

STEP 1: Turn the Power Switch OFF on the rear panel. Slide the SET
switch to the set side.

STEP 2: Turn the power switch ON. The screen will show blinking
SELECT.

STEP 3: Please press GROSS/NET key and a blinking CAL will show
on the screen. Then press the key.

STEP 4: The screen will show F-CAL. Please press the key.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

29
 1Setting Minimum Division
The display of di 1 shows the smallest division. Use the

or key to move through the available divisions.125

102050. Press the key to set the minimum division.

2Setting Decimal F000 will change---see 4-2

The screen will show dp d000.000. A blinking decimal will
show on the screen. Use the or key to move through the
available decimal Point position. Press the key to set the
decimal position.

3Setting Maximum Capacity

When setting maximum capacity, the screen will show CAP

C000.000. Use the or key to set the numeric value, Use

the or key to move through digits. Press the to finish

the step.

4ZERO Adjust
The Screen will display ZERO . Please move the calibration
mass and objects away on the Weighing device then press
key. A display of ....... means finishing the Adjustment.

5SPAN Calibration
The screen will show SPAN . Press key and place your
calibration mass on the weighing device and input weight value.
Use the or key to set the available value, and the or key
to move through digits. Please press the key to finish the
calibration. The screen will show ........

STEP 5 : The screen will show END .

Slide the SET switch to the original side.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

30
 2. Select Digital Calibration
An easy way to make calibration by inputting Load Cells Full Scale Output
voltage

STEP 1: Turn the Power Switch OFF on the rear panel. Slide the SET
switch to the set side.

STEP 2: Turn the power switch ON. The screen will show blinking
SELECT.

STEP 3: Please press GROSS/NET key and a blinking CAL will show
on the screen. Then press the key. The screen will show

F-CAL. Please use the or key to choose digital Calibration

(d-CAL).

STEP 4: The screen will show F-CAL. Please use the or key to
choose digital Calibration (d-CAL). Please press the key.

1Setting Minimum Division

The display of di 1 shows the smallest division. Use

the or key to move through the available divisions.12

5102050. Press the key to set the minimum division.

2Setting Decimal F000 will change---see 4-2

The screen will show dp d000.000. A blinking decimal will
show on the screen. Use the or key to move through the
available decimal Point position. Press the key to set
the decimal position.

3Setting Maximum Capacity

When setting maximum capacity, the screen will show CAP

C000000.Use the or key to move through digits. Use

JIF-2002 WEIGHING INDICATOR&CONTROLLER

31
 the or key to set the numeric value. Press the key to
finish the step.

4Setting Full Scale Output Voltage of the Load Cell Sensors

When setting full scale output voltage of the load cell sensors,
the screen will show LC-CAPL000000.. Please use the
or key to move through digits. Use the or key to set
the numeric value. Press the key to finish the step.

5ZERO Adjust
The Screen will display ZERO . Please move the calibration
mass and objects away on the Weighing device then press
key. A display of ....... means finishing the Adjustment.

6d-SPAN Calibration
The screen will show d-SPAN . Press key and place your
calibration mass on the weighing device and input weight value.
Use the or key and the or key to enter Load Cell O/P
Volt. Please press the key to finish d-SPAN. The screen will
show ........

STEP 5: The screen will show END .

Slide the SET switch to the original side.

Example of selecting FULL CALIBRATION

(Div 2, 3 decimal, Max cap.20)

JIF-2002 WEIGHING INDICATOR&CONTROLLER

32
 Key Screen will display
Turn the Power Switch
OFF
Slide Set switch to the
set side
Turn the power ON. Blinking SECECT
Press GROSS/NET. Blinking CAL
Press key Blinking F-CAL
Press key di 01(Blinking at 01)
Press key di 02(Blinking at 02)
dp d000.000
(Blinking at the Decimal Point---- F000 will
Press key
subject to change if or key been
pressed)
CAP C010.000
Press key
(Blinking at the latest decimal)
Press key 4 times 010.000(Blinking at 1)
Press key 020.000(Blinking at 2)
Press key ZERO
Press key SPAN
Press key 000.000(Blinking at the latest decimal)
Place 1kg Calibration 001.000(Twinkle at 1)
Mass, press key 3
times, press key
Press key End

4-4 PANEL KEY DISABLE

Disable unimportant or unused keys.

STEP 1: Turn the Power Switch OFF on the rear panel. Slide the SET
switch to the set side.

STEP 2: Turn the power switch ON. The screen will show blinking
SELECT.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

33
STEP 3: Please press TARE/CLEAR key and a blinking LOC will show
on the screen. After enter key, a will show on the
screen. Please press the key you wish to disable. The screen
will show the keys number. JIF-2002 will inquire if you want to
lock or unlock the key: 00u or L (Key number00: Unlock
or Lock the key).

STEP 4: Use the or key to choose lock or unlock the key and press
key for confirmation.

STEP 5 : Slide the SET switch to the original side for finishing the step.

4-5 COPY SYSTEM PARAMETER

A backup can be stored to prevent data loss.

System Parameter:
includes functions FXXX, Calibration parameters, disable keys.

STEP 1: Turn the Power Switch OFF on the rear panel. Slide the SET
switch to the set side.

STEP 2: Turn the power switch ON. The screen will show blinking
SELECT.

STEP 3: Please press ACC/CLEAR key and a blinking COPY will show
on the screen. Please enter key.

STEP 4: Use the or key to choose NO or YES . If NO is entered, the

screen will show END. If YES is entered, the screen will
show END .

STEP 5 : Slide the SET switch to the original side for finishing the step.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

34
4-6 RESTORE SYSTEM PARAMETERS
Restoration can be used when system failed or human operation error

happens.

L Restoration will not restore set-point parameters.

System Parameter:
includes functions FXXX, Calibration parameters, disable keys.
Set-point Parameter: includes Final, SP1, SP2, Free Fall, Hi, Lo.

STEP 1: Turn the Power Switch OFF on the rear panel. Slide the SET
switch to the set side.

STEP 2: Turn the power switch ON. The screen will show blinking
SELECT.

STEP 3: Please press Fn key and a blinking RESTORE will show on

the screen. Please enter key.

STEP 4: Use the or key to choose NO or YES . If NO is entered,

the screen will show END. If YES is entered, the screen will
show END .

STEP 5 : Slide the SET switch to the original side for finishing the step.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

35
4-7 CLEAR SET POINT DATA

STEP 1: Turn the Power Switch OFF on the rear panel. Slide the SET
switch to the OFF side (The SET switch remain in OFF status).

STEP 2: Turn the power switch ON. The screen will show Normal
operation condition.

STEP 3: Please press STANDBY key and hold SET POINT/ CODE key
at the same time until the screen shows C Lr cd .Please
release the STANDBY key ( SET POINT/CODE key still
holding). Please release the SET POINT/CODE key in
sequence. Please press the key and the JIF-2002 will
subsequently ask the operator to clear set point data.

STEP 4: Use the or key to choose NO or YES and press the key to
confirm.

4-8 SYSTEM INITILAIZE

Re-install resets the JIF-2002 to the initial factory settings. Use

Re-install only if you want to return Function, Set Point or Calibration

to their initial settings.

STEP 1: Turn the Power Switch OFF on the Rear Panel, and slide SET
switch to he set side.

STEP 2: Turn the power switch ON. The screen will show blinking
SELECT.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

36
 STEP 3: Please press ESC key and a blinking INIT will show on the
screen. Please enter key.

STEP 4: Use the or key to choose NO or YES . If NO is entered, the

screen will show END. If YES is entered, the screen will
show END .

STEP 5 : Slide the SET switch to the original side for finishing the step.

Calibration Errors

C.Err 1The resolution exceeds 116,000.

Change the minimum division and maximum capacity within
116,000.Resolution ratio= Minimum divisionmaximum capacity

C.Err 2The load cell output is too large at ZERO calibration.

Add an additional resistor (50k500K) between EXC+
and SIG.

Refer to the Right Figure

C.Err 3The load cell output is too small at ZERO calibration.

Add an additional resistor (50k500K) between
EXC+ and SIG+.

Refer to the Right Figure

JIF-2002 WEIGHING INDICATOR&CONTROLLER

37
C.Err 4The calibration mass has been mistakenly entered as a
value greater than the maximum capacity.
Please reduce the weight of calibration mass, and re-enter the
weight value.

C.Err 5: The calibration mass has been wrongly entered zero or it is

smaller than the minimum capacity.
Please increase the weight of calibration mass, and re-enter the
weight value.
C.Err 6: The load cell output is too low.
Replace your load cell with a more sensitive one or adjust the
minimum division.

C.Err 7: The load cell signal pins are reversed, or the load cell output
voltage is too low.
Check the load cell connections if reversed or load cell failure.

C.Err 8: The load cell output voltage at maximum capacity is too high.
Check the load cell specification or load cell failure.

C.Err 9: The maximum, capacity has been wrongly entered as a value

smaller than 100.
Check Resolution Table.

C.Err10 :The maximum, capacity has been wrongly entered as a value

greater than 750,000.
Check the load cell specification or load cell failure.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

38
 Display Resolution Table
Maximum Resolution
1 Min. Div. 2 Min. Div. 5 Min. Div. 10 Min. 20 Min. Div. 50 Min. Div.
300 1300 ------------ ------------ ------------ ------------ ------------
400 1400 ------------ ------------ ------------ ------------ ------------
500 1500 ------------ ------------ ------------ ------------ ------------
600 1600 1300 ------------ ------------ ------------ ------------
800 1800 1400 ------------ ------------ ------------ ------------
1,000 11000 1500 ------------ ------------ ------------ ------------
1,200 11200 1600 ------------ ------------ ------------ ------------
1,500 11500 1800 1300 ------------ ------------ ------------
2,000 12000 11000 1400 ------------ ------------ ------------
2,500 12500 11200 1500 ------------ ------------ ------------
3,000 13000 11500 1600 1300 ------------ ------------
4,000 14000 12000 1800 1400 ------------ ------------
5,000 15000 12500 11000 1500 ------------ ------------
6,000 16000 13000 11200 1600 1300 ------------
8,000 18000 14000 11500 1800 1400 ------------
10,000 110000 15000 12000 11000 1500 ------------
12,000 112000 16000 12500 11200 1600 ------------
15,000 115000 18000 13000 11500 1800 1300
20,000 ------------ 110000 14000 12000 11000 1400
25,000 ------------ 112500 15000 12500 11200 1500
30,000 ------------ 115000 16000 13000 11500 1600
40,000 ------------ ------------ 18000 14000 12000 1800
50,000 ------------ ------------ 110000 15000 12500 11000
60,000 ------------ ------------ 112000 16000 13000 11200
80,000 ------------ ------------ ------------ 18000 14000 11500
100,000 ------------ ------------ ------------ 110000 15000 12000
120,000 ------------ ------------ ------------ 112000 16000 12500
150,000 ------------ ------------ ------------ 115000 18000 13000
200,000 ------------ ------------ ------------ ------------ 110000 14000
250,000 ------------ ------------ ------------ ------------ 112500 15000
300,000 ------------ ------------ ------------ ------------ 115000 16000
400,000 ------------ ------------ ------------ ------------ ------------ 18000
500,000 ------------ ------------ ------------ ------------ ------------ 110000
600,000 ------------ ------------ ------------ ------------ ------------ 112000
700,000 ------------ ------------ ------------ ------------ ------------ 114000
750,000 ------------ ------------ ------------ ------------ ------------ 115000
JIF-2002 Display Resolution can reach 1/60,000. (Depends on load cell
quality and performance).
JIF-2002 WEIGHING INDICATOR&CONTROLLER
39
4-9 20mA Current Loop
20 mA Current Loop Specifications

1. Baud Rate 1200 bps

2. Data bit 7 bit
3. Parity Even Parity
4. Stop bit 1 bit
5. Output Code ASCII

CURRENT LOOP
1 20 mA
0 0 mA

Pin Assignment

Pin 1Serial Output

Pin 2Frame Ground
Pin 3Serial Output
Output has no polarity , rather it is
bi-directional.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

40
CHAPTER 5
SET POINTS

JIF-2002 WEIGHING INDICATOR&CONTROLLER

41
5-1 SET POINTS
5-1-1 Change Set point code and Set point values
F106 Input Mode Set Point Input
1 Panel key From Panel key
BCD Input: Code Input From Panel key
2
from rear panel
Serial Input: RS-232 or From Panel key or Serial
3 RS-422/482 when Input
F203=5

How to change Set point Code: After press SET POINT/ CODE key,

please press the key to show the current set-point code.

Use the or key to change set point code and the or
key to change value. Please press the key to finish changing
set-point code. The relay will work according to the specific
set-point code.Please identify the function F106=1.
Otherwise, the operator can only review the set-point codes.

5-1-2 Change Set point values

How to change Values within Set point Codes: Please presskey,
then press SET POINT/CODE key. The screen will show blinking
CODE 00.

STEP 1: Use the or key to change position and the or key to

change set point code. Please press the key to finish
changing set-point code.

STEP 2: The screen will show Final. Please press the key, and the
screen will show 6-digit value with blinking 0 000.000. Use the
or key to change position and or key to change
value. Please press the key to confirm FINAL value.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

42
STEP 3: The screen will show SP1, please press the key. The screen
will show a 6-digit value with blinking 0 000.000. Please use
the or key to change position and the or key to
change value. Please press the key to confirm SP1 value.

STEP 4: The screen will show SP2, please press the key. The screen
will show 6-digit value with blinking 0 000.000. Please use the
or key to change position and the or key to
change value. Please press the key to confirm SP2 value.

STEP 5 : The screen will show Free, please press the key. The screen
will show 6-digit value with blinking 0 000.000. Please use the
or key to change position and the or key to
change value. Please press the key to confirm Free Fall
value.

STEP 6: The screen will show Hi, please press the key. The screen
will show 6-digit value with blinking 0 000.000. Please use the
or key to change position and the or key to
change value. Please press the key to confirm Hi (Over
Limit) value.

STEP 7 : The screen will show Lo, please press the key. The screen
will show 6-digit value with blinking 0 000.000. Please use the
or key to change position and the or key to
change value. Please press the key to confirm Lo (Under
Limit) value.

STEP 8: The screen will show CODE 00, please press the STANDBY
key to leave set point codes. If you wish to continue reset other
SET POINT CODES. Please enter values according to step1 to
step 8 again.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

43
5-2 BATCHING MODES
Batching Modes
1. Customer Programmed Control Mode: Normal Batching
2. Customer Programmed Control Mode: Loss-in-Weight Batching
3. Built-in Automatic Program Mode: Normal Batching
4. Built-in Automatic Program Mode: Loss-in weight Batching
5. Multiple-Ingredient Batching

Customer Programmed Control Mode: Normal Batching

( F101 = 1)

SP1 Full Flow Gate

SP2 Medium Flow Gate
Free Dribble Flow Gate

1. The Weighing Hopper is empty, the display shows "0", and all Gates are
closed. If the display is not at ZERO, input a TARE signal (Pin 24) to
re-ZERO the display.

2. Open the Supply Bin's: Full-Flow Gate, Medium-Flow Gate, and

Dribble-Flow Gate.

3. When the display reaches "Final - SP 1", the SP 1 Output (Pin 12) signal will
come ON. Closed the Full-Flow Gate by using the SP 1 Output ON signal.

4. When the display reaches "Final - SP 2", the SP 2 Output (Pin 11) signal will
come ON.

Closed the Medium-Flow Gate by using the SP 2 Output ON signal.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

44
5. When the display reaches "Final - FREE", the FREE Output (Pin 10) signal
will come ON. Closed the Dribble-Flow Gate by using the FREE Output ON
signal.

6. After Free Fall has stopped - check if the HI and LO (Pin 9, 8) signals are
OFF. If both outputs are OFF then the batch is completed correctly.

7. An Automatic Free Fall Compensation Command (Min. 200ms pulse to Pin

21) may be given at this time. If you change the Free Fall Set Point value
either from the Front Panel or the RS-232C, RS-422/485 the learned
Free Fall value will be cleared.

8. Use the FREE (Pin 10) signal to delay a time period as the control signal is
processing empty the Weighing Hopper.

9. When the GROSS weight is below the ZERO band, the ZERO Band Output
will come ON -signifying the Weighing Hopper is empty. Closed the
Weighing Hopper Discharge Gate by using the ZERO Band (Pin 13) Output
ON signal.

10. You are now ready for your next batching event.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

45
 Customer Programmed Control Mode: Loss-in-Weight
( F101 = 2)

SP1 Supplying Bin Gate

SP2 Full Flow Gate
Free Dribble Flow Gate

1. The Weighing Hopper is empty as is the Receiving Bin. The display shows
"0", and all Gates are closed.

2. Open the Supplying Bin Gate.

3. When the GROSS Weight reaches "SP 1", the SP 1 Output (Pin 12) signal
will come ON. Closed the Supplying Bin Gate by using the SP 1 Output ON
signal.

4. The displayed weight will exceed the SP 1 value by the Free Fall value.
This weight is not necessarily accurate - but accuracy is not needed at this
moment since the purpose of this event is to fill up the Weighing Hopper.
The SP 1 value is always compared to GROSS weight.

5. Input a TARE signal (Pin 24) to ZERO the display.

6. Open the Full-Flow Gate and the Dribble-Flow Gate for Full-Flow filling into
the Receiving Bin.

7. When the display reaches "Final - SP 2", the SP 2 Output (Pin 11) signal will
come ON.

Closed the Full-Flow Gate by using the SP 2 Output ON signal.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

46
8. When the display reaches "Final - FREE", the FREE Output (Pin 10) signal
will come ON. Closed the Dribble-Flow Gate by using the FREE Output ON
signal.

9. After Free Fall has stopped - check to see if the HI and LO (Pin 9, Pin 8)
signals are OFF. If both outputs are OFF then the batch is completed
correctly.

10. An Automatic Free Fall Compensation Command (Min. 200ms pulse to Pin
21) may be given at this time.

11. If the GROSS weight of the Weighing Hopper is below the ZERO Band
(Pin 13), the ZERO Band Output will be ON. The ZERO Band Output will
refill Weighing Hopper if needed.

12. Ready for next batching event.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

47
 Built-in Automatic Program Mode: Normal Batching( F101 = 3 )

SP1 - Full Flow Gate

SP2 - Medium Flow Gate
Free - Dribble Flow Gate
Start signal Pin22

1. The Weighing Hopper is empty, the display shows "0", and all Gates are
closed. If the display is not at ZERO, input a TARE signal (Pin 24) to
re-ZERO the display.

2. Check if the Weighing Hopper is empty using the ZERO Band Output
(Pin 13).

3. Input the Start signal via the Control I/O Interface connector (Pin 22).
When the Start signal is received, then SP 1, SP 2, and Free Output
signals will "come ON".

Note: When the Final Weight is 0, the Pin 12, 11 and 10 are kept OFF.

4. Open the Supply Bin's: Full-Flow Gate, Medium-Flow Gate, and

Dribble-Flow Gate.

5. When the display reaches "Final - SP 1", the SP 1 Output (Pin 12) signal
will come OFF. Closed the Full-Flow Gate by using the SP 1 Output OFF
signal.

6. When the display reaches "Final - SP 2", the SP 2 Output (Pin 11) signal
will come OFF.

Closed the Medium-Flow Gate by using the SP 2 Output OFF signal.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

48
7. When the display reaches "Final - Free", the Free Output (Pin 10) signal
will come OFF. Closed the Dribble-Flow Gate by using the Free Output
OFF signal.

8. Batch Finish signal is sent after the set time period (F103) or when the
display is stable.

9. After Free Fall has stopped - check to see if the HI and LO (Pin 9, 8)
signals are OFF. If both outputs are OFF then the batch is completed
correctly.

10. Automatic Free Fall is now recalculated for the next event.

11. The Weighing Hopper Discharge Gate will be opened using the Finish
Output (Pin7) ON signal.

12. Data Output is sent (Auto print Mode: BCD, RS-232C, RS-422/485,
Printer or Current Loop). The NET Weight data will be accumulated.

13. Ready for the next batching event.

14. If an Abort signal is sent (Pin 21) anytime after the Start signal is
received, then:
(1) SP 1, SP 2 and Free signals will go OFF, and Gates will be closed.
(2) Batch Finish and Data Output signals will be sent.
(3) NET Weight data will be accumulated.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

49
 Built-in Automatic Program Mode: Loss-in-Weight Batching
(F101=4)

SP1 Supplying Bin

Gate
SP2 Full Flow Gate
Free Dribble Flow Gate
Start signal Pin22

1. The Weighing Hopper is empty as is the Receiving Bin. The display shows
"0", and all Gates are closed.

2. Open the Supplying Bin Gate.

3. When the GROSS Weight reaches "SP 1", the SP 1 Output (Pin 12) signal
will come ON. Closed the Supplying Bin Gate by using the SP 1 Output ON
signal.

4. The displayed weight will exceed the SP 1 value by the Free Fall value.
This weight is not necessarily accurate - but accuracy is not needed at this
moment since the purpose of this event is to fill up the Weighing Hopper.
The SP 1 value is always compared to GROSS weight.

5. Input a TARE signal (Pin 24) to ZERO the display.

6. Input the Start signal via the Control I/O interface connector (Pin 22). When
the Start signal is received, the SP 2 and Free Outputs "come ON".

Note : When the Final Weight is 0, the Pin 11 and 10 are kept OFF .

7. Open the Full-Flow Gate and the Dribble-Flow Gate for Full-Flow filling into
the Receiving Bin.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

50
8. When the display reaches "Final - SP 2", the SP 2 Output (Pin 11) signal will
come OFF. Closed the Full-Flow Gate by using the SP 2 Output OFF signal.

9. When the display reaches "Final - FREE", the FREE Output (Pin 10) signal
will come OFF. Closed the Dribble-Flow Gate by using the FREE Output
OFF signal.

10. Batch Finish signal is sent after the set time period (F103) or when the
display is stable.

11. After Free Fall has stopped - check if the HI and LO (Pin 9, 8) signals are
OFF. If both outputs are OFF then the batch is completed correctly.

12. Automatic Free Fall is now recalculated for the next event.

13.The Weighing Hopper Discharge Gate will be opened using the Finish
Output (Pin 7) ON signal.

14. Data Output is sent (Auto print Mode: BCD, RS-232C, RS-422/485, Printer
or Current Loop). The NET Weight data will be accumulated.

15. Signal (Pin 13) will refill using ZERO Band Output if needed.

16. Ready for next batching event.

17. If an Abort signal is sent (Pin 21) anytime after the Start signal is received,
then:(1) SP 1, SP 2 and Free signals will go OFF, and Gates will be closed.
(2) Batch Finish and Data Output signals will be sent.
(3) NET Weight data will be accumulated.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

51
 Multiple-Ingredient Batching
Multiple-Ingredient Batching can be done in any of the four Batch
settings of Function (F101). Accumulation will be performed by
Automatic Free Fall Compensation Command (control I/O Pin 10) in
the Customer-Programmed Control mode and at Final Output in the
Built-in Automatic
Program mode. The
example below is a
Normal Batching
operation in the
Customer
Programmed Control
Mode.

SP1 Full Flow Gate

SP2 Megium Flow Gate
Free Dribble Flow Gate

1. The Weighing Hopper is empty, the display shows "0", and all Gates are
closed. If the display is not at ZERO, input a TARE signal (Pin 24) to
re-ZERO the display.

2. Input the Set Point Code number for Batching.

3. Open the supplying Bin's : Full-Flow Gate, Medium-Flow Gate, and

Dribble-Flow Gate.

4. When the display reaches "Final - SP 1", the SP 1 Output (Pin 12) signal
will come ON. Closed the Full-Flow Gate by using the SP 1 Output ON
signal.

5. When the display reaches "Final - SP 2", the SP 2 Output (Pin 11) signal
will come ON. Closed the Medium-Flow Gate by using the SP 2 Output
ON signal.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

52
6. When the display reaches "Final - FREE", the FREE Output (Pin 10)
signal will come ON. Closed the Dribble-Flow Gate by using the FREE
Output ON signal.

7. An Automatic Free Fall Compensation Command (Min. 200ms pulse to

Pin 21) may be given at this time

8. After Free Fall has stopped - check to see if the HI and LO (Pin 9, 8)
signals are OFF. If both outputs are OFF then the batch is completed
correctly.

9. Please input a TARE signal (Pin 24) and set point code, then preparing
another substance batching.

10. Load the next substance into the Supplying Bin. Prepare the proper
Program, Operator Settings (if needed). Repeat Steps 3 ~ 8.

11. Use the FREE (Pin 10) signal to delay a time period as the control signal
is processing to empty the Weighing Hopper.

12. When the GROSS weight is below the ZERO band, the ZERO Band
Output will come ON which signifying the Weighing Hopper is empty.
Closed the Weighing Hopper Discharge Gate by using the ZERO Band
(Pin 13) Output ON signal.

13. You are now ready for your next batching event.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

53
CHAPTER 6
OPTIONS

JIF-2002 WEIGHING INDICATOR&CONTROLLER

54
6-1 I/O INTERFACE
FINAL
The Total Weight of the batching event with six-digit value.

SP1Optional Preliminary, Set Point 1

Close the Weighing Hopper Full Flow Gate with six-digit value.

SP2 Preliminary, Set Point 2

Close the Weighing Hopper Medium Flow Gate with six-digit value.

FREE FALL
Close the Weighing Hopper Dribble Flow Gate with six-digit value.

HIOver Limit
Please enter six-digit Over Limit Value NET weight > Final + Over Limit
Value

LOUnder Limit
Please enter six-digit Under Limit Value NET weight < Final - Under Limit
Value

CODE INPUT
Pin Pin Name Pin Pin Name
1 11 6 210
2 21 7 410
3 41 8 810
4 81 9 Common
5 110

JIF-2002 WEIGHING INDICATOR&CONTROLLER

55
 Control I / O
Input

JIF-2002 The width of these inputs are at least 200msec

Output

JIF-2002

INPUT SCREW DESCRIPTION

Screw Signal Name Description
JIF-2002 returns to the center of
ZERO when the weighing device is
Pin 25 ZERO Input (Pulse input)
empty

JIF-2002 switches to TARE mode,

ZERO's the display and stores the
Pin 24 TARE Input (Pulse input)
TARE weight in memory.

TARE Reset (Pulse input) TARE value is cleared to "0".

Pin 23

JIF-2002 WEIGHING INDICATOR&CONTROLLER

56
 1Batching will be started when Pin 22
1Built-In program Mode,
is short-circuit to COM1
start Batch Input
2Customer Program- 2When Pin 22 is short-circuit to
Pin 22
control Mode set point COM1, JIF-2002 will stop receiving
data abort read input data from set points, keeping the
previous data.

1When Pin 21 is short-circuit to

1Built-In program Mode, COM1, the batch is aborted and
Abort the Batch (Pulse FINISH signal is sent, and the NET
Input) weight will be accumulated.
Pin 21
2Customer Program- 2When Pin 21 is short-circuit to
control Mode Automatic COM1, JIF-2002 will estimate the free
Free Fall Compensation fall value for the next batch, and the
command (Pulse input). NET weight will be accumulated.

Print Accumulator Accumulator will be printed when P20

Pin 20 short-circuited with COM1.

PRINT Input (pulse input) When FC01, F203=3, F401=3,

F302=2 shorted with COM1, Data will
Pin 19
be sent one time.

Clear Accumulated Value If this command is accepted, all the

and Count accumulated weight and accumulated
Pin 18
(pulse input) count will be cleared.

Pin 17 Input Common (COM1)

or
Pin 16

OUTPUT SCREW DESCRIPTION

Screw Signal Name Description
ZERO BAND Output GROSS Weight ZERO Band
Pin 13
1Batching Mode: NET Weight
Final Weight SP1
Pin 12 SP1 Output 2Loss-in-weight Mode: GROSS
Weight SP1

SP2 Output NET Weight Final Weight SP2

Pin 11
Free Fall Output NET Weight Final Weight Free
Pin 10 Fall

JIF-2002 WEIGHING INDICATOR&CONTROLLER

57
 HI Output NET Weight Final Weight + HI
Pin 9
LO Output NET Weight Final Weight LO
Pin 8
FINAL Output Built-In program Mode: send signal at
Pin 7 Final.

1 F105 = 0: Output at Stable; Shorted

when motion. 2 F105 = 1: 1Error
Motion Detection / Error occurred, 2over Zero Band range,
Pin 6
Output or3Over weight capacity or printer
error.

Pin3.
Output 12V
Pin4
Pin 1.
Output Common
Pin2

6-2 BATCHING MODES

SERIAL RS-232 OP- 02

11200 BPS 2400 BPS

F 200 Baud Rate
34800 BPS 49600 BPS

F 201 Parity 0 Non-parity Even Parity 2Odd Parity

Same as display 2 Gross Weight 3 NET

F 202 Output Data Weight 4 TARE Weight 5 Gross Weight, NET
Weight, TARE Weight

Stream 2 Stable and auto print 3 Manual

F 203 Output Mode Print Mode 4 Accumulate and Print
5 Command Mode

Sending without Set point Code 1 Sending

F 204 Output Format
with set point Code

JIF-2002 WEIGHING INDICATOR&CONTROLLER

58
 OP-02
RS-232 RS-232C

Specifications
Type EIA-RS-232C 12V
Transmission Half Duplex, Asynchronus Transmission
Baud Rate 1200BPS2400BPS4800BPS9600BPS
Bit
8 bit non- parity 7 bit even parity, odd parity
Parity
Stop Bit 1 bit
Output Code ASC II

I/O Specifications
25 Pin D- Shape

JIF-2002 WEIGHING INDICATOR&CONTROLLER

59
 9 Pin D- Shape

Pin 2 TDTransmit Data

Pin 5 SGSignal Ground

Serial InterfaceOP-02Data Format.

Format1Data Update speed 4 times/Sec or 17 times/Sec
C D 0 1 S T N T 0 0 5 4 3 2 1 k g Cr Lf
CODE Code Header 1 Header 2 Data8 digits in length
UNIT
number

HEADER 1
t Over Max. Capacity or under
O L
Min. Capacity
S T t STABLE
U S t UNSTABLE

HEADER 2
N T t NET
G S t GROSS
T R t TARE

UNIT
k G t Kilogram
l B t Pound

ASCII data characters

0 ~ 9
Space20H
Decimal Point2EH
Minus2DH
Plus2BH

JIF-2002 WEIGHING INDICATOR&CONTROLLER

60
Command List Table
Sending Command to JIF-2002 response
JIF-2002
R Cr Lf Sending latest data once (Data format
READ depends on F202)

Z Cr Lf JIF-2002 display will ZERO. Z Cr Lf will be

ZERO sent by JIF-2002.

T Cr Lf JIF-2002 will go to NET Mode and display

TARE will TARE. T Cr Lf will be sent by JIF-2002.

N Cr Lf JIF-2002 will go to NET Mode. N Cr Lf will

NET be sent by JIF-2002.

G Cr Lf JIF-2002 will go to GROSS Mode. G Cr Lf

GROSS will be sent by JIF-2002.

If an invalid character is receivedCr Lf will be sent by the JIF-2002

If the commands are not accepted for any reasonI Cr Lf will be sent
by the JIF-2002

Sending Command to JIF-2002 response

JIF-2002
Send back signal BB
BB Cr Lf
BB an only be received in the Built in
BEGIN BATCHING
Automatic Program Control Mode
Send back signal HB
HB Cr Lf
HB an only be received in the Built in
HALT BATCHING
Automatic Program Control Mode
Sending Final NET weight
RF Cr Lf
If B Cr Lf is send by JIF-2002, that means
READS FINAL NET batching is still in process.
Signal S Cr Lf will send back by JIF-2002.
S Cr Lf
JIF-2002 will send back SET POINT CODE
SETPOINT until totally receive SET POINT CODE data.
SS XX Cr Lf will send back by JIF-2002.
SS Cr Lf
JIF-2002 will send back SET POINT values
SET SETPOINT
until totally receive SET POINT values.
RS Cr Lf JIF-2002 receives signal RS xx Cr Lf, and
READ SET POINTS read xx set point value.
JIF-2002 will send back signal SA Cr Lf.
SA Cr Lf
JIF-2002 will send back ZERO band data
SET ACCESSORIES
until totally receive Zero Band Value.
RA Cr Lf JIF-2002 receives signal RS xx Cr Lf, and
READ ACCESSORIES read xx Zero Band Value.
CC Cr Lf JIF-2002 will send back signal CCXX Cr Lf
CODE CHANGE and send back ZERO band data (F1063)

JIF-2002 WEIGHING INDICATOR&CONTROLLER

61
Command Format SSXX Cr Lf
6 5 4 3 2 1 4 5 6 7 8 9 0 2 3 4 5 6
yFinal ySP1 ySP2

1 2 3 4 1 2 3 4 1 2 3 4 Cr Lf
y Free Fall y HI yLO

Command Format SA Cr Lf
0 0 3 4 5 6 Cr Lf
Zero Band Range

6-3 PRINTER INTERFACE

(INCLUDING DATE AND TIME)
PRINTER OP-03
Setting Date, Setting Year. Month, day, hour, minute, second
F 300
Time
F 301 Data Format
0Not print Only print above the latest data
Date
2Print on all
0 Not print 1Only print above the latest data
Time
Print on all
0 Not print Only print above the latest data
Set
2Print on all
Serial Number Not print 1Print
Same as display 2Gross Weight 3NET
Weight
Weight 4TARE Weight 5Gross Weight, NET Weight,
TARE Weight6Gross Weight, TARE Weight,
NET Weight
0Not print Only print above the latest data
according to F001 2Only print above the latest
Unit data g 3Only print above the latest data t
4Print on all according to F001 5Print on all g
6Print on all t
1Stable and auto print Manual Print Mode
F 302 Output Mode
3Accumulate and Print
F 303 Select Printer MINI Printer 2Normal Printer

JIF-2002 WEIGHING INDICATOR&CONTROLLER

62
 PIN ASSIGNMENTS:

PIN PIN NAME PIN PIN NAME

1 /STROBE 14 NC
2 DATA1 15 /ERROR
3 DATA2 16 /INIT
4 DATA3 17 NC
5 DATA4 18 NC
6 DATA5 19 NC
7 DATA6 20 GROUND
8 DATA7 21 GROUND
9 DATA8 22 GROUND
10 /ACKNLG 23 GROUND
11 NC 24 GROUND
12 NC 25 GROUND
13 NC

6-4 PARALLEL BCD INTERFACE

BCD OP-04
Same as display 2 Gross data 3 NET data
F 400 Data type
4 TARE data
Stream 2 Stable and print 3 Manual print
F 401 Output Mode
mode4 Accumulate and print
F 402 Output Logic Positive Logic 2 Negative Logic

JIF-2002 WEIGHING INDICATOR&CONTROLLER

63
Pin Pin Name Pin Pin Name
1 GROUND 26 NC
HiNETLo
2 11 27
GROSS
3 21 28 NC
4 41 29 NC
5 81 30 NC
6 110 31 NC
7 210 32 NC
8 410 33 LoMOTION
9 810 34 11 CODE
10 1100 35 21
11 2100 36 41
12 4100 37 81
13 8100 38 110
14 11000 39 210
15 21000 40 410
16 41000 41 810
17 81000 42 LoNegative Polarity
18 110000 43 / Decimal Point 1
19 210000 44 / Decimal Point 2
20 410000 45 / Decimal Point 3
21 810000 46 / Decimal Point 4
22 1100000 47 HiOverload
23 2100000 48 NC
24 4100000 49 PRN 1
25 8100000 50 / Busyinput

JIF-2002 WEIGHING INDICATOR&CONTROLLER

64
 OPEN COLLECTOR TYPE
Maximum Voltage30V
Maximum Current24mA
Please add a pull-up resistance if connected to a TTL LOGIC.

6-5 ANALOG OUTPUT OP-05

Analog Output
F 500 Analog Output Data Output 4~20 mA Output 0~+10 V
Same as display 2Gross data
F 501 Output Mode
3NET data
Loss-in-weight Not read Absolute Value
F 502
Absolute Value 1 JIF-2002 reads Absolute Value
Output current
F 503 0.0mA through 9.99mA (Initial 0.40mA)
when display ZERO
Output current at
F 504 0.0mA through 9.99mA (Initial 20.0mA)
Full Capacity
Output Volt when
F 505 -2.5V through +59.9V (Initial 00.0 V)
display ZERO
Output Volt at Full
F 506 -2.5V through +59.9V (Initial 10.0 V)
Capacity

OP-5 OUTPUT 4 ~ 20 mA Specifications

Output Level 4~20 mA effective range. Output range is
approximately 2 to 22 mA
Resolution More than 1 / 1000
Temperature (0.015 % / of rdg + 0.01mA) /
Coefficient
Maximum 500 Maximum
If you add a 250 resistor , the output will be 1V to 5V (4~20mA)

JIF-2002 WEIGHING INDICATOR&CONTROLLER

65
 LThis resistor must be large enough for proper power consumption.
Use the following formula: W = I R where
W: Power I: Output Current R: Resistor

If a 500 resistor is used , power consumption will be :

W = (0.02) 500 = 0.2 when the Output Current is set to 0.2mA
The resistor should have a power greater than "0.5" (w = 0.5) and
have a very low temperature coefficient. In this example power
consumption is "0.2" and thus, the500 resistor is adequate.

Setting Output Current

IOUT = IZ + ( weight / capacity ) * ( IM - IZ ) (if 2<= IOUT <=22 mA)

IOUT: Output Current
IZ: Output at ZERO (F501)
IM: Output at Maximum Capacity (F502)

Example: A weighing system has a Maximum Capacity of 10,000kg. If you

Want the Output current to be 4mA at ZERO display, and 20mA at
1/2.

Maximum Capacity then:

IM = capacity / simulated) (IOUT IZ) IZ
IM = 10000 / 5000 (20 mA 4 mA) 4 mA = 36 Ma

When Output at Full Scale is set at 36mA, and Output Current at Display
ZERO is set at 4mA, then at 1/2 Capacity (5000kg) the Output Current will be
20mA.NOTE: The Maximum Output will be saturated at 22mA.

OP-6 ANALOG OUTPUT 010V

Output Level 0~+10 V effective range. Output range is
approximately -1.25~11.25 V
Resolution More than 1 / 1000
Temperature (0.015 % / of rdg + 0.01mA) /
Coefficient
Minimum 5 K Minimum
If you add a 10 K resistor , the output will be 0mA to 1mA (0~10 V)

JIF-2002 WEIGHING INDICATOR&CONTROLLER

66
L This resistor must be large enough for proper power consumption.
Use the following formula: W = V /R where
W: Power V: Output Voltage R: Resistor

Setting Output Voltage

VOUT = VZ + (weight / capacity ) * ( VM - VZ ) (if 0<= VOUT <=10 V)
VOUT: Output Voltage
VZ: Output at ZERO (F505)
VM: Output at Maximum Capacity (F506)

NOTE: The Maximum Output will be saturated at 11.25.

JIF-2002 WEIGHING INDICATOR&CONTROLLER

67