CONTENTS

1 General Description....................................................................................... 1
1.1 Functions and Characteristics ....................................................... 1
1.2 Front Panel......................................................................................... 2
1.3 Technical Specifications................................................................... 3
1.3.1 Common................................................................................ .3
1.3.2 Analog.....................................................................................4
1.3.3 Digital...................................................................................... 4
2 Installation and Wiring................................................................................... 5
2.1 Connection of Power Supply........................................................... 5
2.2 Connection of Load Cell................................................................... 5
2.2.1 6-wired Connection.............................................................. 6
2.3 I/O terminals....................................................................................... 7
2.4 Optional Expansion Board Output.................................................. 8
2.4.1 Analog Output (Optional) ................................................. 8
2.4.2 Serial Interface RS485 Output..........................................11
2.4.3 Serial Interface RS232 Output......................................... 12
3 Calibration..................................................................................................... 13
3.1 Instruction......................................................................................... 13
3.2 Flow Chart of Calibration............................................................... 14
3.3 Millivolt Value Display..................................................................... 20
3.4 Calibration with Weights.................................................................20
3.5 Millivolt Calibration.......................................................................... 20
3.6 Calibration Switch for Communication Interface........................ 22
3.7 Explanation for Calibration Parameters.......................................23
4 Working Parameters Setting...................................................................... 25
4.1 Flow Chart of Working Parameters Setting.................................25
4.2 Parameter Setting Method.............................................................27
4.3 Descriptions of Operation Parameters........................................ 28
4.4 Set point parameters...................................................................... 31
5 I/O Definition................................................................................................. 33
5.1 I/O Definition.................................................................................... 33
5.2 I/O testing......................................................................................... 35
6 Serial Communication................................................................................. 36
 6.1 r-Cont................................................................................................ 37
6.2 r-SP1................................................................................................. 37
6.2.1 Parameters Code Chart.................................................... 37
6.2.2 Error Code Explanation..................................................... 40
6.2.3 Command............................................................................ 40
6.3 tt TOLEDO....................................................................................... .48
6.4 Cb920................................................................................................49
6.5 rECont............................................................................................... 50
6.6 rEREAD............................................................................................ 51
6.7 Modbus............................................................................................. 52
6.7.1 Modbus Communication Address.................................... 53
7 Password Input and Setting, Reset.......................................................... 59
7.1 Password Input................................................................................ 59
7.2 Password Setting............................................................................ 59
7.3 Factory Reset.................................................................................. 61
8 Display Testing............................................................................................. 63
9 Errors and Alarm Messages.......................................................................64
10 Dimension of Indicator.............................................................................. 65
1 General Description
M02 weighing indicator is specially designed for weight transmitting in industrial
fields.
This indicator has the features of small volume, plenty communicating commands,
stable performance, easy operation and practicability. It can be widely applied to
concrete and bitumen mixing equipment, metallurgy furnace and converter, chemical
industry and feed, etc. .
1.1 Functions and Characteristics
Small volume, unique design, easy operation
Applicable to all kinds of resistance strain gauge bridge load cell
Front panel numerical calibration
Multilevel of digital filter
Automatic zero -tracking
Automatically zero when powered on
4 set points
1 input and 2 outputs
Serial communication interface:RS232 or RS485
Calibration via serial interface
Optional interfaces: Analog output, serial interface

1
1.2 Front Panel

M02 Front panel

Main Display:6 digits, for displaying weight and the information of parameters.
Status Indicator Lamp:
ZERO: Light on when present weight is within 0±1/4d.
STAB: Light on when changes of weight values are within the range of motion
detecting during motion detecting time.
HOLD: Light on when indicator displays the value of D/A output.
Keypad:

2
 : Zero/Esc, Used to exit from current operation or go previous.

: Used to scroll optional values of parameter and to make flashing digit

increase 1 while data inputting.

: Function Selecting Key, To make flashing position move to the right digit
when data inputting.

: Confirming Key. Used to confirm present operation.

1.3 Technical Specifications

1.3.1 Common:
Power supply: DC24V±5%
Working temperature: -10 40
Max humidity: 90%R.H without dew
Power consumption: About 10W
Dimension: 110×89×60 mm

3
1.3.2 Analog:
Load cell power: DC5V 200mA MAX
Input impedance: 10M
Zero steady range: 0.00 12mV(Load cell 3mV/V)
Input sensitivity: 0.1uV/d
Input range: 0.00 15mV(Load cell 3mV/V)
Transfer mode: Sigma - Delta
A/D conversion speed: 15, 30, 60, 120, 480, 960 times/sec
Non-linearity: 0.01% F.S
Gain drift: 10PPM/
Display Precision: 1/100,000
1.3.3 Digital:
Weight display: 6 digits red high-brightness LED
Minus display: -
Overload display: OFL
Decimal point: 5 kinds (optional)
Function keys: 4 keys soniferous keypad

4
2 Installation and Wiring
2.1 Connection of Power Supply
M02 weighing indicator connects DC24V power supply as follows:

Power supply connection

2.2 Connection of Load Cell

M02 weighing indicator connects bridge type resistance strain gauge load
cells by 6 wires or 4 wires as follows. When you use 4-wired load cells, you must
bridge the SN+ with EX+ and bridge the SN- with EX-.
The signal definition of each port of the load cell connector is as follows:
EX+: Excitation+ EX-: Excitation- SN+: Sense+ SN-: Sense- SIG+: Signal+ SIG-: Signal-

5
 6 wires EX+ SN+ EX- SN- SIG+ SIG- Shield

4 wires EX+ EX- SIG+ SIG- Shield

2.2.1 6 wires connection

Note:
1. As load cell output sensitive analog signal, please use shield cable to separate
with other cables, especially AC power.
2. 4 wires connection is suitable for short distance and stable temperature or low
precision field, otherwise use 6 wires connection.
3. For more load cells parallel connection, their sensitivity (mV/V) should be same.

6
2.3 I/O terminals

I/O tolerant definition as follows:

Output Input
OUT1 Stable IN1 Reset
all
OUT2 OFL

Indicator input terminal connection:

Indicator input terminal connection:

7
2.4 Optional Expansion Board Output
M02 weighing indicator supports analog output, RS232 or RS485 as optional

output function, please confirm it when place orders.

2.4.1 Analog Output (Optional)

At normal displaying status, press to check the analog output.

The definition of analog output as below:

8
 The definition of analog output:
V+: voltage-output+, V-: voltage-output-
I+: current-output +, I-: current-output -

Analog output two types:

1) Voltage output: 0-5V/0-10V is optional .
2) Electric current output: 4-20mA/0-20mA/0-24mA is optional.
3) User-define function, users can define analog output type and output range.

The analog output has been calibrated before the delivery of the indicators, so
users do not need to make calibration. If analog output is abnormal, users can
calibrate by themselves as follows: Suggestion: please calibrate under the
instruction of professionals)

Normal display status

Note: only support calibration under current

mode. 4 points must be finished for current

SET UP calibration.

9
 and
In this interface the
Current calibration interface multimeter measured
should be 4.000mA.

If not,press
Measured 4.000mA

This interface is current DA If yes,press

D/A,press to adjust the value, In this interface the

and the current value measured will multimeter measured
vary accordingly.To adjust it when the should be 4.000mA.
measured value to be 4.000mA, then

press to save and exit. Finish the calibration referring to the process of
4.000mA calibration, and the same for the
Then press to calibrate calibration of 20mA.
12.000mA.

10
 This interface is the highest
point calibration of analog
output.

In the interface of highest point calibration,press to enter into analog

display value interface, the display will be 5 digits (initial value is 24000, means

24.000mA),press to input the value measured by the multimeter.

Note: Analog output calibration, highest point must be calibrated.
2.4.2 Serial Interface RS485 Output
Serial Interface RS485 output is optional, please refer to chapter 6.0 for
communication protocol.
RS485 serial interface connection:

11
3 Calibration
3.1 Instruction
1 Calibration procedure must be executed when a M02 indicator is put in use at the
first time, the preset parameters may no longer meet the user s needs, and any part of
the weighing system was changed. Position of decimal point, minimum division,
maximum capacity, zero, and gain can be set and confirmed through calibration.

2 If you want to set only one parameter, please press to save parameter s

value and then press to exit.

3 Please see section 3.7 for parameter instruction.

4 Please record each value in the blank table in section 3.4 during calibration for the
emergency use in future.
5 See chapter 9 for error alarm message that may be displayed during calibration.

13
3.2 Flow Chart of Calibration
1. Under this status, press (twice),
indicator will display CAL, then

Normal Status press to enter password input.

2. After password is input, the indicator will

display CALON for one second, then go to

next step.

Password input 3. Press to select a desired value for

decimal point among 0,
0.0, 0.00, 0.000 and 0.0000, and then

press to save it and enter next step.

If no need to change the value,

Decimal point
press directly to enter next step.

14
 4. Press to select a desired value for min.
division among 1,2,
5,10,20 and 50, and then to save it and enter next
step.
Min. divistion If there no need to change the value, then

press directly to enter next step.

5. Input max. capacity( min. division×100000),

press to save it and enter next step.

If there no need to change the value, then
Max. capacity
press directly to enter next step.

6. Under this status, press to enter zero

calibration.
Display value near the output value in millivolt
between SIG+/SIG- of load cell.
Millivolt value display See section 3.3 for details about this function.

15
 7.Unloaded scale first, when STAB lamp is on,

press to finish zero calibration.

If there no need to calibrate zero,
Zero calibration
press directly to enter gain calibration.

16
8. The process of gain calibration is as follows. If there s no need to do gain calibration, press

directly to enter serial ports calibration switch setting.

17
9. Press to enter setting interface,

press to choose the switch position,

press to set password to set

switch position, then press to enter password

setting.

10. See section 7.2 for reference to set password.

If there s no need to set password,

press directly to go back to normal

status.

18
3.3 Millivolt Value Display
This function is mainly used for system test, position-error test for weighing
mechanism and linearity test for load cell.
1. System Test
(1) If display data changes with loaded weight changes, it shows that connection
of load cell is correct and weighing mechanism works well.
(2)If display value is OFL (or OFL), it means that loaded weight on load cells is
too large (or too small). Please unload the weight (or load more), if display value is still
OFL (or OFL), the possible reasons are as follows:
a. There is something wrong with weighing mechanism, please check and clear.
b. The connection of load cell is incorrect, please check and clear.
c. Load cells may be damaged, please replace.
2. Position-error Test for Weighing Mechanism
Load a same weight on each corner of weighing mechanism and record
displayed millivolt value respectively. If differences among these values are obvious,
please adjust weighing mechanism.
3. Linearity Test for Load Cell
Load same weight for several times, and record displayed value every time. If
one or two values are obviously much larger or smaller than any others, it means that
the linearity of load cell is bad.
*NOTE: You must use to zero display data before weight is
loaded for each time.

19
3.4 Calibration with Weights
During calibration with weight please record the zero millivolt value, gain millivolt
value and the loaded weight value in the blank table below. If it is not convenient to load
a weight to calibrate, these values can be used for calibration without weights.
Zero millivolt Gain millivolt Loaded Date Remarks
value(mV) value(mV) Weight
1
2
3
4
5
3.5 Millivolt Calibration
When it is not convenient to load a weight to calibrate alibration can be done without
weights using recorded data in the table in section 3.4.
However, this method is just used for some emergencies, it will make calibration
result incorrect if load cells, or indicator has been replaced.

20
21
22
3.6 Calibration Switch for Communication Interface
When calibrate the transmitter through serial port( Rs SP1 or Modbus), must set to
ON status for the calibration switch for communication interface.
3.7 Explanation for Calibration Parameters
Symbol Parameter Types Value of parameter Default
Pt Decimal Point 5 0 0.0 0.00 0.000 0.0000 0
1d Min. Division 6 1 2 5 10 20 50 1
CP Max. Capacity Min. Division×100000 10000

t Millivolt Value

o Zero

C Gain
Switch for
Calibration
SIOCAL via serial OFF
interface

PASS Password Setting 000000

23
Log Table for Calibration Parameters
Parameter Calibrated Value Date Remarks
Decimal Point
Min. Division
Max. Capacity
Load cell sensitivity
Password

24
4 Working Parameters Setting

4.1 Flow Chart of Working Parameters Setting

Normal Status

SET UP If F4.1(Password Switch) is ON, you

should input password first.

F1 F1.1 F1.7

1 .Use to select between the same level. Switch from

display F1 to F2, press .

25
F2 F2.1 F2.7

2 .Press to enter into sub-selection, press to

return back to previous menu.

When it displays F2,press to enter into F2.1.

F3 F3.1 F3.2

F4 F4.1

26
4.2 Parameter Setting Method
M02 has 2 kinds of working parameters: Selection type and data type. For

selection type parameters, press to choose. For data type parameter in

parameter interface, press to choose digit position, pressto choose value.

Selection:

F1.1 OFF ON F1.1

Enter setting status Change OFF to ON Confirm the change

Data:

F1.4 50 50 60

Enter setting status Move the flashing from 0 to 5 Adjust value

Confirm change
F1.4
27
4.3 Descriptions of Operation Parameters
Code Default Description
F1 Null The first major term of working parameter.
F1.1 OFF Switch for Auto-Zeroing when power-on,
OFF: disabled ON: enabled
F1.2 0 Zero-tracking Range 0 9d optional .
This parameter is for automatic calibration, disabled
when is set .
F1.3 1 Motion Detecting Range 1 9d optional)

F1.4 50 Zeroing Range 00% 99% of Maximum capacity

F1.5 5 Digital filtering parameter: (1-9 as optional)

0: without filtering
9: strongest digital filtering
Stable filter parameter the second filter based on the
F1.6 0 first filter : (1-9 as optional)
0: without filtering
9: strongest digital filtering
F1.7 0 A/D conversion rate: 120,480,960,15,30,60 as optional

28
 F2 Null The second major term of working parameter.
F2.1 01 Scale no., indicator no.
F2.2 9600 Baud rate of serial port

F2.3 Cb920 Serial ports communication mode:

Modbus-RTU MODBUS RTU mode;
r-Cont:SP1 continuous mode;
r-SP1: SP1 command mode
tt:TOLEDOcontinuous mode
Cb920 Cb920 continuous mode
rE-Cont:rE continuous mode
rE- rEAd:rEcommand mode

F2.4 Data format:

7-E-1 7 data bits even parity check 1 stop bit
7-O-1 7data bits odd parity check 1 stop bit
7-E-1 8-E-1 8 data bits even parity check 1 stop bit
8-O-1 8 data bits odd parity check 1 stop bit
8-n-1 8 data bits no parity check 1 stop bit
8-n-2 8 data bits no parity check 2 stop bit

29
 HiLo MODBUS dual-byte register storage turn Hi Lo
F2.5 High byte in the front, low byte at the back Lo Hi Low
byte in the front, high byte at the back
F2.6 nonE Cont mode automatic sending time interval
tt(TOLEDOcontinuous mode)If send the checksum
F2.7 0
0 not send, 1 send.
The third major term of working parameter.
F3 Null
(For analog output only)
Analog output:
4-20 4-20mA
0-20 0-20mA
0-24 0-24mA
F3.1 0-5 0-5: 0-5V
0-10: 0-10V
I_out Current customized
V_out Voltage customized
In customized mode,F3.2-F3.5 parameters available
F3.2 3920 Minimum output
F3.3 4000 Zero point output

30
 F3.4 20000 Maximum capacity output
F3.5 20020 Maximum output
F4 Null The fourth major term of working parameter.
F4.1 OFF Parameters password setting switch.
F4.2 000000 Parameters password setting:Valid when F4.1 is ON
4.4 Set point parameters
Code Default Description
P1-P4 Null The first term of working parameters
PX.1 OFF Change of state if need stable

PX.2 0.0 Change of state minimum duration

PX.3 P1.3=1 Condition of validity

0 forbid
P2.3=5 1 <
2 <=
P3.3=0
3 ==
P4.3=0 4 >=
5 >

31
 6 != compare to minimum value
7 _<>_outside the range, need to set 2 edge value
8 =< >=inside the range, need to set 2 edge value
9 external trigger. If it s IO do 1 state change for 1
trigger, if it s command, then decide according to
valid or invalid command.
PX.4 0 Set value 1 Set value 1 and set value 2, choose the
minimum to compare
PX.5 0 Set value 2

Set point has 4 major terms which are user defined.

32
5 I/O Definition
5.1 I/O Definition
Output/Input code table:

Output

Code Definition Description

O0 None No definition

O1 Stable Effective output in stable status.

O2 Overflow Effective output when overflow.

O3 Sp1 Effective output when set point 1 status output.

O4 Sp2 Effective output when set point 2 status output.

O5 Sp3 Effective output when set point 3 status output.

O6 Sp4 Effective output when set point 4 status output.

33
 Input

Code Definition Description

I0 None No definition

I1 Zeroing Effective input for zeroing, pulse input signals

I2 Sp1 If this signal is valid, Sp1 status will be regarded as

invalid. Output valid state when comparision condition
turns to invalid, and be effective again.
I3 Sp2 If this signal is valid, Sp2 status will be regarded as
invalid. Output valid state when comparision condition
turns to invalid, and be effective again.
I4 Sp3 If this signal is valid, Sp3 status will be regarded as
invalid. Output valid state when comparision condition
turns to invalid, and be effective again.
I5 Sp4 If this signal is valid, Sp4 status will be regarded as
invalid. Output valid state when comparision condition
turns to invalid, and be effective again.

34
I6 Reset all Reset all paramater value when this signal is valid.

5.2 I/O testing

Under weighing status,press (5 times) then

display TESTio press enter into I/O testing

interface.
Normal Status

Press OUT1 status flash, press OUT2

status flash.

This interface shows:IN1 input valid, OUT1 output valid.

35
6 Serial Communication
M02 has RS232 or RS485 as optional to realize communication with upper
computer Support r-Cont r-SP1 Modbus(bus) tt TOLEDO Cb920 rECont
protocols and rErEAD protocol.
Serial communication terminal please refer to chapter 2.4.2 2.4.3. Baud rate and
communication format setting please refer to F2.2 F2.3 and F2.4.

Under main display display weight value), long press to enter into serial
communication checking interface, it will display ------ if no communication, and ------
will flash if there s communication.

6.1 r-Cont
Indicator will send weighing data to host computer without command.
Data Format:
STX Scale Channel Status Value CRC CR LF
no. no.
Here:
STX 1bit start character 02H
Scale no. 2bits 00~99
Status 2bits high byte:40H low byte definition as follows:

36
 D6 D5 D4 D3 D2 D1 D0
G./N. Zero
Null Null +/- OFL Stable
weight point
0 + 0 0 0 not
1 0 0 1 - non/zero normal stable
1 zero 1 OFL 1 stable
Weight Value 6 bits when weight is+ - overflow,return to space space OFL
space
CRC 2 bits,check sum
CR 1 bit 0DH
LF 1 bit 0AH
For example:
02 30 31 31 4041202020373030 32 34 0D 0A
Means: stable,positive data,present weight 700

6.2 r-SP1
Code : ASCII
Operation code supported: W write R, read C calibrate O, zero
6.2.1 Parameters Code Chart

37
Operation Para. code Para. Name number of character
code
R WT Read current status 8
and weight
R SP Read set point status 4
W DC Write mini. Divistion and 8
max. capacity
R/W PT Decimal point digit 1
R DD Minimum division 2
R CP Maximum capacity 6
R/W AC Auto. Zeroing switch 1
R/W TR Zero tracking range 1
R/W MR Stable range 1
R/W ZR Zeroing range 2
R/W FL digital filtering para. 1
R/W VC steady filtering 1
R/W AD AD sample rate 1
R PO Set point output status 4
R/W P1M~P4M Set point to judge if 1
need stability
R/W P1T~P4T Set point minimum 3
duration time
R/W P1F~P4F Set point comparison 1
condition to judge
R/W P1L~P4L Set point lower edge 6

38
 value to judge
R/W P1H~P4H Set point upper edge 6
value to judge
7: D6D5D4D3D2D1D0;
R AM Absolute millivolt D6:+;D5-D0: corresponding ASCII for 6 digits
millivolt,Decimal point is fixed to 3 digits
7 D6D5D4D3D2D1D0
R RM Relative zero point on D6 +/-;D5-D0:corresponding ASCII for 6
millivolt digits Decimal point is fixed to 3 digits
C ZY Zero calibration with
weight
C ZN Zero calibration 6
without weight
C GY Gain calibration with 6
weight
C GN Gain calibration 12
without weight
O CZ Zero clearing
command
O P1S~ Setting the Valid when 9,command valid when external
P4S corresponding set trigger and 1 status change for 1 external
point Trigger
O P1C~P4 Clear the
C corresponding set
point

39
6.2.2 Error Code Explanation
1 CRC check error
2 Operation code error
3 Parameters code error
4 Write data error
5 Operation invalid
6 Channel no. error
Note Default channel no. of this indicator : 1 31H
6.2.3 Command
Indicator will send weighing data to host computer after received command.
6.2.3.1 Host computer read present status
Send command:
STX Scale no. Channel No. R WT CRC CR LF
Correct response:
STX Scale Channel R WT Status Value CRC CR LF
no. No.
Wrong response:
STX Scale Channel R WT E Error code CRC CR LF
no. No.

Here

40
 STX 1bit start character 02H
R 1 bit 52H
WT 2 bit 57H 54H
E 1 bit 45H
Status 2bits high byte: 40H low byte definition as follows:
D6 D5 D4 D3 D2 D1 D0
G./N.
Null Null +/- Zero point OFL Stable
weight
0 + 0 non/zero 0 normal 0 not stable
1 0 0
1 - 1 zero 1 OFL 1 stable

Weight Value 6 bits when weight is+ - overflow,return to space space OFL
space
For example:
02 30 31 31 525754 30 31 0D 0A
Correct response 02 30 31 31 52 57 54 4041303033373533 33 36 0D 0A
stablepresent value 3753
Wrong response: 02 30 31 31 52 57 54 4531 31 39 0D 0A CRC check error
6.2.3.2 Read other parameters
Send command:
STX Scale no. Channel No. R Para. code CRC CR LF

41
Correct response:
STX Scale no. Channel No. R Para. code Value CRC CR LF
Wrong response:
STX Scale Channel R Para. E Error code CRC CR LF
no. No. code

Here:
Para. Value 1bit
Para. code 2 bits
For example:
02 30 31 31 524D52 3839 0D 0A
Correct response 02 30 31 31 52 4D 52 36 34 33 0D 0A stable range 6
Wrong response:02 30 31 31 53 4D 52 4532 30 39 0D 0A Operation code error
6.2.3.3 Write max. Capacity and min. Division
Send command:
STX Scale Channel W DC Division Max. CRC CR LF
no. No. value capacity
Correct response:
STX Scale no. Channel No. W DC O K CRC CR LF
Wrong response:
STX Scale Channel W DC E Error code CRC CR LF

42
 no. No.
Here:
DC 2 bits 44H 43H
O 1 bit 4FH
K 1 bit 4BH
Division value 2 bits 1/2/5/10/20/50
Max. capacity 6 bits
For example:
02 30 31 315744433035303130303030 36 30 0D 0A(division value 5, Max capacity
10000)
Correct response: 02 30 31 31 57 44 43 4F 4B 32 34 0D 0A
Wrong response: 02 30 31 31 57 44 43 4535 39 32 0D 0A Operation ca t execute
6.2.3.4 Write other parameters
Send command:
STX Scale Channel W Para. Para. CRC CR LF
no. No. code value
Correct response:
STX Scale Channel W Para. O K CRC CR LF
no. No. code
Wrong response:
STX Scale Channel W Para. E Error CRC CR LF

43
 no. No. code code
For example:
02 30 31 31575A523530 30 38 0D 0A Write zeroing range to 50
Correct response: 02 30 31 31 57 5A 52 4F 4B 36 31 0D 0A
Wrong response: 02 30 31 31 57 5A 53 4533 32 38 0D 0A Para. Code error
6.2.3.5 Calibration Zero
1 Calibrate zero as per current weight with weight
Send command:
STX Scale no. Channel No. C ZY CRC CR LF
Correct response:
STX Scale no. Channel No. C ZY O K CRC CR LF
Wrong response:
STX Scale no. Channel No. C ZY E Error code CRC CR LF
Here:
Z 1 bit 5AH
Y 1 bit 59H
For example:
02 30 31 31 435A59 39 34 0D 0A
Correct response:02 30 31 31 43 5A 59 4F 4B 34 38 0D 0A
Wrong response:02 30 31 34 43 5A 59 4536 32 30 0D 0A channel no. error
2 Input millivolt calibration zero in the chart without weight

44
Send command:
STX Scale no. Channel No. C ZN Zero millivolt value CRC CR LF
Correct response:
STX Scale no. Channel No. C ZN O K CRC CR LF
Wrong response:
STX Scale no. Channel No. C ZN E Error code CRC CR LF
Here:
ZN 2 bits 5AH4EH
Zero millivolt value 6 bits
For example:
02 30 31 31 435A4E303132363130 38 31 0D 0A
Correct response:02 30 31 31 43 5A 4E 4F 4B 33 37 0D 0A
Wrong response:02 30 31 31 43 5A 4E 4534 30 34 0D 0A Write data error
6.2.3.6 Gain calibration
1 With weights
Send command:
STX Scale no. Channel No. C GY Weight value CRC CR LF
Correct response
STX Scale no. Channel No. C GY O K CRC CR LF
Wrong response:
STX Scale no. Channel No. C GY E Error code CRC CR LF

45
 Here:
GY 2 bits 47H 59H
Weight value 6 bits: Write in weight value
For example:
02 30 31 31434759303030323030 36 35 0D 0A Write in: weight value 200
Correct response: 02 30 31 31 43 47 59 4F 4B 32 39 0D 0A
Wrong response: 02 30 31 35 43 47 59 4536 30 32 0D 0A Channel no. error
2 Without weights
Send command:
STX Scale no. Channel No. C GN Gain millivolt Weight value CRC CR
Correct response:
STX Scale no. Channel No. C GN O K CRC CR LF
Wrong response:
STX Scale no. Channel No. C GN E Error code CRC CR LF
Here:
Gain millivolt 6 bits
Weight value 6bits
For example:
02 30 31 3143474E303031393430303030323030 35 36 0D 0A (Write in:
weight value 200 corresponding gain millivolt 0.194
Correct response: 02 30 31 31 43 47 4E 4F 4B 31 38 0D 0A
Wrong response: 02 30 31 31 43 48 4E 4533 38 35 0D 0A Para. Code error

46
6.2.3.7 Zeroing
Send command:
STX Scale no. Channel No. O CZ CRC CR LF
Correct response:
STX Scale no. Channel No. O CZ O K CRC CR LF
Wrong response:
STX Scale no. Channel No. O CZ E Error code CRC CR LF
For example:
02 30 31 31 4F 43 5A 38 34 0D 0A
Correct response: 02 30 31 31 4F 43 5A 4F 4B 33 38 0D 0A
Wrong response: 02 30 31 31 4F 43 5A 4535 30 36 0D 0A Operation ca t execuate
6.2.3.8 CRC computation
All the values in front of the parity bit add together and convert to decimal data,
then convert the last 2 bits to ASCII code (decade in front and the unit at the back).
For example

The following is a frame of data:

0 3 3 3 4 4 5 3 3 0 0

Add 02~5A: 180(Hex),convert to decimal data: 384. We can calculate from this

47
that the check code is 38,34 for the data frame.
6.3 tt TOLEDO Protocol
When choose tt protocol in working parameter F2.3, indicator will send datas in
continuous mode with TOLEDO protocol.
Continuous sending mode format as below:
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

STX 0D
A B C display weight(6 bits) 6 30H Checksum

Here:start character is standard ASII start character 02(STX)

status byte A definition as below:
D0 0 1 0 1 0
D1 1 1 0 0 1
D2 0 0 1 1 0
Decimal point x .x .xx .xxx .xxxx
D3 D4 D6 0(not change) D5 is 1(not change)

48
 status byte B definition as below:

D6 D5 D4 D3 D2 D1 D0

Status Stable Overflow symbol G.W.

Is 0 Is 1 Is 1 1-unstable 1-overflow 1-negative Is 0
(not change) (not change) (not change) 0-stable 0-normal 0-positive (not change)
status byte C is reserved, output 20H.

6.4 Cb920
When F2.3=Cb920 in working parameter, indicator will send weighing data
continuously without command under Cb920 protocol.
Data format

Status G.W. 0/1 Symbol Display Unit CR LF

Here
Status 2 bits OL ( 4FH 4CH ) OFL ST ( 53H 54H )Stable US ( 55H
53H )unstable

49
 1 bit separator 2CH
G.W. 2 bits GS: gross weight 47H 53H
0/1 1 bit (30H/31H) interleaved transmission
Symbol 1 bit, 2BH + , 2DH -
Display 7 bits including decimal point
Unit 2 bits blank space 20H 20H
CR 1 bit 0DH
LF 1 bit 0AH
For example: When indicator send the following automatically:
53 54 2C 47 53 31 2B 20 20 31 39 30 2E 31 20 20 0D 0A
Means: Stable G.W. Data value is positive current weight is 190.1
6.5 rECont
Indicator will send weighing data to the upper computer continuously without any
command.
Return data frame format specification
Status GS +/- Display Unit CR LF

50
 2bits 2C 47 53 2C 2B/2D 7bits 6B 67 0D 0A

Here:
Status 2 bits OL(OFL):4FH 4CH; ST(stable):53H 54H; US(unstable):55H 53H
Display value 7bits, including decimal point, high bit is blank if no decimal point.
For example: When indicator send the following automatically:
5354 2C 47 53 2C 2B3031312E313230 6B 67 0D 0A
Means Stable Data value is positive display value is 11.120kg
6.6 rEREAD
Indicator will send weighing data to the upper computer under command.
Data format
Data R E A D CR LF
explain 52H 45H 41H 44H 0DH 0AH
The return data frame is the same with that of rECont protocol, please refer to rECont.

51
 6.7 Modbus
Indicator uses RTU mode to communicate, every 8-bit byte of the message are
divided into 2pcs of 4-bit hexadecimal characters to transmit at binary code.
Code: Binary
Function code:

Function code Definition Description

03 read the register
06 preset single register
16 preset several registers Command only support preset double registers.
01 read coil
05 write coil The length unit is bit.

Exception code response

Code Definition Description

02 Illegal data address Data address received from error code is not allowed
03 Illegal data value Data wrote in is not in permissible range
04 When indicator is trying to execuate operation required,
machine fault
unrecoverable error is produced.
07 Unsuccessful Command received ca t be execuated under current

52
 programming condition.
request
6.7.1 Modbus communication address
PLC addr. Display Description
addr.
The following items are only-read register(code 0x03)
40001 0000 Present weight value(4bits including sign characters, the
40002 0001 high bit is in the front)
40003 0002 D15 D14..D5 D4 D3 D2 D1 D0

All is 0 0:+ 0:non-zero 0:normal 0:unstable

1:- 1: zero 1:OFL 1:stable
40004 0003
Reserve(permit to read, reading value is 0 )
40006 0005
The following items are two bytes and are available to read and write
(write code 0x06 read code 0x03
40007 0006 Zeroing(zeroing when write in non-zero value)
40008 0007 Automatically zeroing when power on 0 OFF 1 ON
40009 0008 Zero tracking range 0-9d

53
40010 0009 Stable range 1-9d
40011 0010 Zeroing range 0%-99%
40012 0011 Digit filter parameters(0-9)
40013 0012 Stability filter series(0-9)
40014 0013 AD sample rate 0:15/s 1:30/s 2:60/s 3 120 /s
4:480/s 5:960/s
40015~ 0014~
Reserved
40018 0017
40019 0018 Decimal point place 0:0bit,1:1bit,2:2bits,3:3bits,4:4bits
40020 0019 Minimum division 1/ 2/ 5/ 10/ 20/ 50
The following items are available to read and write
(writing code 0x10 read code 0x03
40021 0020
Maximum capacity max.capacity mini.division×100000
40022 0021
40023 0022 Zero calibration with weights: write in 1 and calibrate zero
40024 0023 with the current weight.
Read: Absolute millivolt of current load cell
40025 0024 Zero calibration without weights: Write millivolt value at
zero Write in range load cell 3mV/V:millivolt value range
40026 0025 within 0.02-12.000mV) millivolt value at zero when read.

54
40027 0026 Gain calibration with weights. Write weight value( max.
capacity). Return millvolt at present weight value when
40028 0027 read
40029 0028 Gain calibration without weights input gain millivolt(load
cell 3mV/V:0.000 millivolt<15.000mV zero
40030 0029
millivolt).Read: millivolt value for gain calibration.
40031 0030 Gain calibration weight without weights. input gain
millivolt( max. capacity) Read: weight value for gain
40032 0031 calibration.
40033~40040 0032~0039 reserved
40041 0040 Set point 1 stable or not 0 no 1 yes
40042 0041 Set point 1 min. duration time 0-999 : 0-99.9sec.
40043 0042 Set point 1 valid condition
40044~40045 0043~0044 Set point 1 set value 1
40046~40047 0045~0046 Set point 1 set value2
40048 0047 Set point 2 stable or not 0 no 1 yes
40049 0048 Set point 2 min. duration time 0-999 : 0-99.9sec.
40050 0049 Set point 2 valid condition
40051~40052 0050~0051 Set point 2 set value1
40053~40054 0052~0053 Set point 2 set value2

55
40055 0054 Set point 3 stable or not 0 no 1 yes
40056 0055 Set point 3 min. duration time 0-999 : 0-99.9sec.
40057 0056 Set point 3 valid condition
40058~40059 0057~0058 Set point 3 set value 1
40060~40061 0059~0060 Set point 3 set value 2
40062 0061 Set point 4 stable or not 0 no 1 yes
40063 0062 Set point 4 min. duration time 0-999 : 0-99.9sec.
40064 0063 Set point 4 valid condition
40065~40066 0064~0065 Set point 4 set value 1
40067~40068 0066~0067 Set point 4 set value 2
40069 0068 Output 1 user-defined
40070 0069 Output 2 user-defined
40071 0070 Input 1 user-defined
40072 0071 I/O output value Note: available only when coil address
I/O input value 00016 is valid.
40073 0072 Input write 1 valid 0 invalid.
Read 1 valid 0 invalid
The following items are bit read only. read code: 0x03
49001 9000 Version no. If display10024 formatXX XXXX,main

56
 version no., hardware no., software
49002 9001 no..So main version no.01 hardware
no. 00 software no. 24
49003 9002 If display 141024, means 24th Oct.,
Develop time
49004 9003 2014
The following items are bit read only. read code 0 x 0 1
00001 0000 0 unstable 1 stable
00002 0001 0 normal 1 OFL
00003 0002 0 non-zero 1 zero
00004 0003 0 + 1 -
00005 0004 Reserved
00006 0005 Reserved
The following item are available to read and write
read code 0x01 writing code 0x05
00007 0006 Automatically zeroing when power on 0 OFF 1 ON
00008 0007 Reserved
00009 0008 Reserved
00010 0009 Reset all

57
00011 0010 Reset calibration
00012 0011 Reset paramaters
00013 0012 Reset I/O
00014 0013 Reserved
00015 0014 Reserved
00016 0015 I/O testing switch
00017 0016 Set point 1 status
00018 0017 Set point 2 status Only read
00019 0018 Set point 3 status 0:invalid 1:valid
00020 0019 Set point 4 status
00021~ 0020~
Reserved
00032 0031

58
7 Password Input and Setting, Reset

7.1 Password Input

1 Indicator calibration and working paraters setting default password: 000000.
2 User can set password in parameters when F4.1 is ON .
3 When display is PASS , need to input correct password to enter parameters.
Note:
1 When input password, if first time wrong, it will go to the second chance for
password input(display from turn to ).
2 If second input wrong, it will enter into interface for inputting password the third
time
(Display change from to ).
3 If Input wrong for three times, main display show Error4 and self-lock, but user
can operate when power on again.

7.2 Password Setting

1 User can set password in parameters when F4.1 is ON .

59
2 User must input same new password twice in setting password,If not same, main

display show Error one second and return to PASS again.

60
 7.3 Factory Reset
Note: Factory reset is only for special technicists, which will reset all of
parameters and will maybe cause not working.

Take reset all for example:

In working status,
Normal working status SET UP press 1 time to display
SET UP.

Press and the

same time to display PASS ,
PASS then password input.

Password input interface, input

fixed password 880202, then
880202 0----
press save password
and enter parameter reset.

61
 1 In F SEt interface, press to reset working
parameters, enter into reset calibration paramters
F SEt interface.

2 In F SEt interface, press not to make working
parameter reset, enter into calibration para. Reset
interface.

F 1 In F CAL interface, press to reset calibration
para., enter into reset all interface.

2 In F CAL interface, press not to make

calibration para. reset, enter into reset all interface.

1 In F ALL interface, press to make reset all of

F the paramters including working para., calibration
para., I/O etc..

Note: In all reset interfaces, press to exit and return to weighing

interface.

62
8 Display Testing
The following flow chart is to test lights on main-display and status lights.
Normal weighing status
Under parameter interface,
Press 5 times
press to switch
SEt UP t ESt t tESt interface.
Under tESt nterface,press

to make display testing,

8.8.8.8 Nixie tube display and indicator
lights all shine. Now if

press , display
will sparkle.
After testing is finished,
t ESt
press to return
t tESt nterface.

63
9 Errors and Alarm Messages
Error Input error.
wrong data beyond parameter range.

Error 2 The present weight value is out of zeroing range.

Error 3 Scale platform is not stable when zeroing.

Error 4 Input wrong password more than 3 times.

OFL Weighing value is positive overflow.

-OFL Weighing value is negative overflow.

64
 10 Dimension of Indicator

Dimension of rear panel:92×45(mm)

Dimension of front panel:105×57(mm)

Panel cutout dimension:93×46(mm)

65