JMS 616 GS-N.L: Technical Specification

Jenbacher gas engines
Technical Specification
JMS 616 GS-N.L

Natural gas 2.433kW el.
GE Jenbacher GmbH & Co OHG
Tel. +43 5244 600-0
http://information.jenbacher.com
A-6200 Jenbach, Austria
Fax +43 5244 63255
jenbacher.info@ge.com

JMS 616 GS-N.L

Natural gas 2.433kW el.
CO-GEN Module data:
Additional information:
Electrical output
kW el.
2.433
Sound pressure level (engine, average value 1m)
dB(A)
101
Recoverable thermal output (120 C)
kW
2.420
Sound pressure level exhaust gas (1m, 30 off engin
dB(A)
119
Energy input
kW
5.669
Fuel Consumption based on a LHV of
Exhaust gas mass flow rate, wet

Exhaust gas volume, wet
9,5 kWh/Nm
Nm/h
597
Electrical efficiency
42,9%
Exhaust gas temperature at full load
Thermal efficiency
42,7%
Combustion air mass flow rate
Total efficiency
85,6%
Combustion air volume
kW
134
Heat to be dissipated (LT-Circuit)

Emission values:
Max.admissible exhaust back pressure after engine
Max. inlet cooling water temp. (intercooler)
mbar
C
[8]
60
395
kg/h
14.389
Nm/h
11.131
40
10
Return temperature
70
Forward temperature
90
m/h
103,9
Hot water flow rate
Engine data:
14.797
11.658
mbar
Max. pressure drop in front of intake-air filter

NOx < 250 mg/Nm (5% O2)
kg/h
Nm/h
Alternator:
Engine type
J 616 GS-E02
Configuration
V 60
No. of cylinders
16
Manufacturer
STAMFORD
Type
LVSI 804 W
Type rating
kVA
3.555
Bore
mm
Stroke
mm
220
lit
99,80
Efficiency at p.f. = 1,0
97,5%
Nominal speed
rpm
1.500
Efficiency at p.f. = 0,8
96,6%
Mean piston speed
m/s
11
Ratings at p.f. = 1,0
kW
2.433
Mean effe. press. at stand. power and nom. spe
bar
20,00
Ratings at p.f. = 0,8
kW
2.410
Epsilon
11,0
Frequency
Hz
50
kW
2495
Voltage
690
Piston displacement
Compression ratio
ISO standard fuel stop power ICFN
Spec. fuel consumption of engine
Specific lube oil consumption
Weight dry
Filling capacity lube oil
Based on methane number|Min. methane numb
190
kWh/kWh
2,27
Protection Class
g/kWh
0,30
Insulation class
IP 23
kg
10.000
Speed
rpm
1.500
lit
530
Mass
kg
6.752
MZ
94|80
Technical parameters:
Applicable standards:
Based on DIN-ISO 3046
Standard conditions:
Air pressure:
Based on VDE 0530 REM with specified tolerance

1000 mbar or 100 m above sea level
Air temperature:
25C or 298 K
Relative Humidity:
30%
Engine output derating:
for plants installed at > 500m above see level and/or intake temperature > 30C, the reduction of engine power is
determined for each project.
Gas quality:
according to TA 1000-0300
Gas flow pressure:
80 - 200 mbar
(Lower gas pressures upon inquiry)
Prechamber gas pressure: 3,3-4,0 bar
Max. variation in gas pressure: 10%
All data are based on engine full load at specified media temperatures and are subject to change.
The technical Instruction TA 1100-0110 "PARAMETER FOR GE Jenbacher GAS ENGINES" must be strictly observed.

>>> Scope of supply genset - JGS 616 GS-N.L
Basic engine equipment:
Module equipment:
*Exhaust gas turbocharger, Intercooler
*Base frame for gas engine,
*Motorized carburator for LEANOX control
alternator and heat exchangers
*Electronic contactless high performance ignition system
*Internal pole alternator with excitation alternator and
*Lubricating oil pump (gear driven)
with automatic voltage regulator; p.f. 0,8 lagging to 1,0
*Lubricating oil filters in main circuit
*Flexible coupling, bell housing
*Lubricating oil sump; Lubricating oil heat exchanger
*Anti-vibration mounts
*Jacket water pump
*Air filter
*Fuel-, lubricating oil and jacket water pipe work on engine
*Automatic lube oil replenishing with level control
*Flywheel for alternator operation; Exhaust gas manifold
*Wiring of components to module interface panel
*Viscous damper
*Crankcase breather
*Knock sensors
*Jacket water electric preheating
Engine accessories:
*Electric starter motor
*Electronic speed governor
*Electronic speed monitoring device including starting and
overspeed control
Module control panel:

*Totally enclosed , single door cubicle, wired to terminals and
*Transducers and switches for oil pressure, jacket water temp.,

jacket water pressure, charge pressure and mixture temperature
ready to operate, protection IP 41 outside,

IP 10 inside, according to VDE-standards
Control equipment:
*One thermocouple per cylinder
*Engine-Management-System dia.ne (Dialog Network)
Supplied loose:
**Visualisation (industry PC-10'' color graphics display): Operation data,
Gas train according to DIN-DVGW consisting of:

*Manual stop valve, fuel gas filter, two solenoid valves,
Leakage control device, gas pressure regulator
controller display,Exh. gas temp.,Generator electr. connection,etc.

**Central engine- and module control: Speed-, Power output-,
LEANOX-Control and knock control, etc.
Prechamber Gas Train
*Multi-transducer
Documentation:
*Lockable operation mode selector switch
*Operating and maintenance manual
Positions: "OFF", "MANUAL", "AUTOMATIC"
*Spare parts manual
*Demand switch
*Drawings
Assembly, painting, testing in Jenbach/Austria
>>> Scope of supply module - JMS 616 GS-N.L

Identical to Genset except that heat recovery is included.
*jacket water heat exchanger mounted on module frame
*exhaust gas heat exchanger mounted as separate heat recovery module
*all heat exchangers with complete pipework
*Heat exchangers and all inherent auxiliaries
Scope of Supply & Design Subject to Local Regulations and product development

Genset
Main dimensions and weights (approximate value)
Connections (at genset)
Length L
mm
8.300
Jacket water inlet and outlet
DN/PN
Width B
mm
2.200
Exhaust gas outlet
DN/PN
600/10
Height H
mm
2.800
Fuel gas (at gas train)
DN/PN
100/16
DN/PN
65/10
100/10
Weight empty
kg
23.300
Intercooler water connection:
Weight filled
kg
24.300
Low Temperature Circuit
100/10
Module
Connections (at module)
Length L
mm
8.300
Hot water inlet and outlet
DN/PN
Width B
mm
2.200
Exhaust gas outlet
DN/PN
600/10
Height H
mm
2.800
Fuel gas (at gas train)
DN/PN
100/16
DN/PN
65/10
Weight empty
kg
23.800
Intercooler water connection:
Weight filled
kg
24.800
Intercooler water-Inlet/Outlet 2nd stage
Heat recovery module
Connections (on heat recovery module)
Width B
mm
1.962
Hot water inlet and outlet
DN/PN
100/10
Height H
mm
4.600
Exhaust gas outlet
DN/PN
600/10
Length L
mm
5.800
Condensate drain
DN/PN
65/10
''
''
Drain line
GE Jenbacher GmbH & Co OHG

A-6200 Jenbach, Austria
Tel. +43 5244 600-0
http://information.jenbacher.com
Fax +43 5244 63255
jenbacher.info@ge.com
04. Jul 2006

JMS 616 GS-N.L: Technical Specification

Uploaded by

Copyright:

Available Formats

JMS 616 GS-N.L: Technical Specification

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

JMS 616 GS-N.L: Technical Specification

Uploaded by

Copyright:

Available Formats

Jenbacher gas engines

JMS 616 GS-N.L

GE Jenbacher GmbH & Co OHG

Tel. +43 5244 600-0

A-6200 Jenbach, Austria

Fax +43 5244 63255

Jenbacher gas engines

JMS 616 GS-N.L

Sound pressure level (engine, average value 1m)

Recoverable thermal output (120 C)

Sound pressure level exhaust gas (1m, 30 off engin

Fuel Consumption based on a LHV of

Exhaust gas mass flow rate, wet

Exhaust gas temperature at full load

Combustion air mass flow rate

Combustion air volume

Heat to be dissipated (LT-Circuit)

Max.admissible exhaust back pressure after engine

Max. inlet cooling water temp. (intercooler)

Hot water flow rate

Max. pressure drop in front of intake-air filter

Efficiency at p.f. = 1,0

Efficiency at p.f. = 0,8

Mean piston speed

Ratings at p.f. = 1,0

Mean effe. press. at stand. power and nom. spe

Ratings at p.f. = 0,8

Based on DIN-ISO 3046

Based on VDE 0530 REM with specified tolerance

Engine output derating:

Prechamber gas pressure: 3,3-4,0 bar

Max. variation in gas pressure: 10%

Jenbacher gas engines

*Exhaust gas turbocharger, Intercooler

*Base frame for gas engine,

*Motorized carburator for LEANOX control

alternator and heat exchangers

*Electronic contactless high performance ignition system

*Internal pole alternator with excitation alternator and

*Lubricating oil pump (gear driven)

with automatic voltage regulator; p.f. 0,8 lagging to 1,0

*Lubricating oil filters in main circuit

*Flexible coupling, bell housing

*Lubricating oil sump; Lubricating oil heat exchanger

*Jacket water pump

*Fuel-, lubricating oil and jacket water pipe work on engine

*Automatic lube oil replenishing with level control

*Flywheel for alternator operation; Exhaust gas manifold

*Wiring of components to module interface panel

*Jacket water electric preheating

Module control panel:

*Transducers and switches for oil pressure, jacket water temp.,

ready to operate, protection IP 41 outside,

*One thermocouple per cylinder

*Engine-Management-System dia.ne (Dialog Network)

**Visualisation (industry PC-10'' color graphics display): Operation data,

Gas train according to DIN-DVGW consisting of:

controller display,Exh. gas temp.,Generator electr. connection,etc.