NHPLRSC
NHPLRSC
NHPLRSC
nhp.com.au
nhp-nz.com
The solution
Applications
Key benefits
1 - direct switch
2 - M350
During
the thermal interchange which occurs decreases the resistance
2.5 run-up,
3 - 2 step metallic resistance
4 - load torque then short circuits the low residual resistance.
and a timed contactor
2
The progressive
decrease in resistance provides smooth and continuous
acceleration, hence the motor
reaches full speed in the shortest possible time
1
with1.5the absence of mechanical stress.
As the
1 resistance decreases
2 in direct relation to the motor speed, the possibility
of operator misuse is minimised and motor burn-out problems are resolved.
3
0.5
FLEXIBILITY
% speed
0 starters25
M350
are easily50adjustable75on-site to100meet changes in torque or load.
Torque
starting the electrolyte strength.
This
iscomparison
achievedduring
by altering
resistance
1
T/FLT
2.5
1 - direct switch
2 - M350
3 - 2 step metallic resistance
4 - load torque
2
1
1.5
1
2
3
0.5
% speed
0
25
50
75
100
% speed
0
25
50
100
resistance
1
75
ENVIRONMENTAL STABILITY
A layer of oil is floated on top of the electrolyte to form a seal which not only
minimises evaporation, but eliminates contamination from the atmosphere.
CLIMATIC CONDITIONS
Whether in the snow fields, or the desert regions of the outback, M350 starters
are operating almost maintenance free. Their only requirement is the need to
occasionally top them up with drinking water (pH = 7 to 9) every 12 months or so.
AVAILABILITY
For ratings up to 750 kW very quick deliveries can be achieved as all
components required for construction are available ex-stock.
M350 electrode assembly.
One of two or three used in an M350 starter.
M350 RATINGS
M350 starters are designed to meet the starting torque requirements of the application
and the starting duty (starting time and starts per hour) specified by the user. The ratings
given to M350 starters are therefore variable and application dependant.
Starter model Nominal motor kW rating at starting torque of;
Single motor drives
0.7 x FLT
1.0 x FLT
1.4 x FLT
2.0 x FLT
M350/2
500
355
250
185
M350/3
750
650
450
315
Notes:
Nominal ratings only, based on four consecutive starts followed by two starts per hour from hot.
Actual ratings will depend on start torque and run up time required.
FLT = Full Load Torque otherwise referred to as Motor Rated Torque.
Output signals
Ready to start
Shorting (Run) contactor closed
Electrolyte level (Low)
Electrolyte temperature (High)
Starter fault
1 x normally open
1 x normally open
1 x normally open
1 x normally open
1 x normally open
Indication
Start
Run
Fault
Electrolyte level low
Electrolyte temp high
Metering
Rotor current
1 x analogue meter
(displays initial start current)
Electrolyte temperature
HLR RATINGS
HLR starters are designed to meet the starting torque requirements of the application
and the starting duty (starting time and starts per hour) specified by the user. The ratings
given to HLR starters are therefore variable and application dependant.
Starter model Nominal motor kW rating at starting torque of;
Single motor drives
0.7 x FLT
1.0 x FLT
1.4 x FLT
2.0 x FLT
HLR700
1,400
1,000
700
500
HLR1100
1,600
1,100
790
550
HLR1400
2,600
1,800
1,300
900
HLR2300
4,200
3,000
2,100
1,500
HLR4000
6,200
4,500
3,100
2,200
HLR4000/2
12,400
9,000
6,200
4,400
2 x 1000
2 x 700
2 x 500
2 x 360
2 x 4,200
2 x 3,000
2 x 2,100
2 x 1,500
HLR4000 Dual
2 x 6,200
2 x 4,500
2 x 3,100
2 x 2,200
HLR4000/2 Dual
2 x 12,400
2 x 9,000
2 x 6,200
2 x 4,400
3 x 1,500
3 x 1,000
3 x 700
Notes:
Nominal ratings only, based on four consecutive starts followed by two starts per hour from hot.
One start per hour from hot for HLR4000 models.
Actual ratings will depend on start torque and run-up time required.
For higher starts per hour or for extended run-up times, a heat exchanger may be added.
Electrode movement and run-up time controlled by inbuilt variable speed drive.
FLT = Full Load Torque otherwise referred to as Motor Rated Torque.
Control of larger motors is possible. Contact NHP for selection assistance and advice.
Multi-motor applications
sales@nhp.com.au
2. Is the electrolyte prepared on-site
or is it supplied premixed in
drums?
The electrolyte is prepared on-site. The
Liquid Resistance Starter is first filled
to maximum with potable water. A
suitable container (~10 litres) is filled
with water electrolyte via the LRS drain
valve and approximately 1/2 kilogram
of the supplied Sodium Carbonate is
mixed into the container contents until
completely dissolved. The contents
of the container are then returned to
the LRS tank via the open lid, evenly
distributed with care to ensure that
the carriage linear bearings are not
splashed. This process is repeated until
the entire dose of Sodium Carbonate
delivered with the starter has been
added. During the first few actual start
cycles, most of the dissolved oxygen
will be driven out of the electrolyte.
At this stage a thin layer of oil (also
supplied with the starter) is then
floated on the electrolyte surface to
minimise evaporation.
3. If the electrolyte is prepared
on-site, are there any specific
requirements for chemical
characteristic and purity of potable
water?
Either plain potable (drinking) water
or, if not available, demineralised water
are suitable. Bore water should not be
used.
10
Company name*
Contact name*
Contact phone*
email*
Stator volts*
Motor kW rating*
Rotor volts*
Stator amps
Rotor amps*
Number of poles
Ambient temperature*
Temperature range*
Yes
No
11
Model
Height
(mm)
Width
(mm)
Length
Dry
Operating
(mm) Weight (kg) Weight (kg)
M350/2
915
1010
1060
350
M350/3
915
1010
1050
355
Model
Height
(mm)
Width
(mm)
710
HLR700
1480
1460
1700
430
1350
715
HLR1100
1640
1460
1700
440
1565
HLR1400
2040
1920
1700
800
2235
HLR2300
1730
1500
2800
1010
3365
HLR700DUAL
2040
1920
1700
800
2235
Note:
Dimensions exclude optional heat exchangers and subject to change without notice.
Not to be used for construction purposes.
12
Length
Dry
Operating
(mm) Weight (kg) Weight (kg)
Length
Dry
Operating
(mm) Weight (kg) Weight (kg)
Model
Height
(mm)
Width
(mm)
1880
4320
3700
3200
11400
HLR4000/2DUAL 1880
4320
3700
3200
11400
Height
(mm)
Width
(mm)
HLR2000DUAL
1700
5800
HLR4000DUAL
HLR4000
1520
5620
HLR4000/2
1880
2140
3700
1700
5800
HLR4000/3
1890
5990
HLR1300/3
1890
5990
Length
Dry
Operating
(mm) Weight (kg) Weight (kg)
Note:
Dimensions exclude optional heat exchangers and subject to change without notice.
Not to be used for construction purposes.
13
HLR 2300
Application:
Motor Rating:
1 x 3,250 kW motor
Duty:
14
Starter Type
HLR 2300
Application:
Pump drive
Motor Rating:
1 x 2,700 kW motor
Duty:
Application:
Motor Rating:
3 x 630 kW motors
Duty:
HLR 2300
Application:
Motor Rating:
1 x 3,800 kW motor
Duty:
15
AUSTRALIA
Queensland
Victoria
Sydney
30-34 Day Street North
Silverwater
NSW 2128
Tel +61 2 9748 3444
Brisbane
16 Riverview Place
Murarrie
QLD 4172
Tel +61 7 3909 4999
Melbourne
43-67 River Street
Richmond
VIC 3121
Tel +61 3 9429 2999
Newcastle
575 Maitland Road
Mayfield West
NSW 2304
Tel +61 2 4960 2220
Townsville
5 Leyland Street
Garbutt
QLD 4814
Tel +61 7 4779 0700
Laverton
104-106
William Angliss Drive
Laverton North
VIC 3026
Tel +61 3 9368 2901
Campbelltown
2/8 Rose Street
Campbelltown
NSW 2560
Tel +61 2 4620 4311
Rockhampton
14 Robison Street
QLD 4701
Tel +61 7 4927 2277
Albury / Wodonga
847 Ramsden Drive
Albury
NSW 2640
Tel +61 2 6049 0600
ACT
nhp.com.au
Dandenong
40-42 Cyber Loop
Dandenong South
VIC 3175
Tel +61 3 8773 6400
Tasmania
Hobart
2/65 Albert Street
Moonah
TAS 7009
Tel +61 3 6228 9575
Launceston
3/13-17 Merino Street
Kings Meadows
TAS 7249
Tel +61 3 6345 2600
Canberra
1/187 Gladstone Street
Fyshwick
ACT 2609
Tel +61 2 6280 9888
Western Australia
Perth
38 Belmont Ave
Rivervale
WA 6103
Tel +61 8 9277 1777
Northern
Territory
Darwin
3 Steele Street
Winnellie
NT 0820
Tel +61 8 8947 2666
Toowoomba
Cnr Carroll Street and
Struan Court
QLD 4350
Tel +61 7 4634 4799
Cairns
2/1 Bramp Close
Portsmith
QLD 4870
Tel +61 7 4035 6888
South Australia
Adelaide
36-38 Croydon Road
Keswick
SA 5035
Tel +61 8 8297 9055
NEW ZEALAND
nhp-nz.com