Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 234 views

    Ats With Acb With MG Controller (LS)

    Uploaded by

    KhajaBurhan
    1. This document provides notes on connecting an ATS with ACBs that uses an M/G controller circuit and optional OCR-II or OCR-III trip relays. 2. It specifies control power requirements and connections for the OCR-II and OCR-III trip relays. 3. The notes indicate a self-maintenance circuit may be needed with OCR-II due to its instantaneous alarm contact, but is not needed with OCR-III, and control power should be input from the primary power source.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Ats With Acb With MG Controller (LS)

    Uploaded by

    KhajaBurhan
    234 views1 page
    1. This document provides notes on connecting an ATS with ACBs that uses an M/G controller circuit and optional OCR-II or OCR-III trip relays. 2. It specifies control power requirements and connections for the OCR-II and OCR-III trip relays. 3. The notes indicate a self-maintenance circuit may be needed with OCR-II due to its instantaneous alarm contact, but is not needed with OCR-III, and control power should be input from the primary power source.

    Original Description:

    Ats With Acb

    Original Title

    Ats With Acb With Mg Controller (Ls)

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    1. This document provides notes on connecting an ATS with ACBs that uses an M/G controller circuit and optional OCR-II or OCR-III trip relays. 2. It specifies control power requirements and connections for the OCR-II and OCR-III trip relays. 3. The notes indicate a self-maintenance circuit may be needed with OCR-II due to its instantaneous alarm contact, but is not needed with OCR-III, and control power should be input from the primary power source.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    234 views1 page

    Ats With Acb With MG Controller (LS)

    Uploaded by

    KhajaBurhan
    1. This document provides notes on connecting an ATS with ACBs that uses an M/G controller circuit and optional OCR-II or OCR-III trip relays. 2. It specifies control power requirements and connections for the OCR-II and OCR-III trip relays. 3. The notes indicate a self-maintenance circuit may be needed with OCR-II due to its instantaneous alarm contact, but is not needed with OCR-III, and control power should be input from the primary power source.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    ATS with ACBs (M/G controller circuit)

    Note) 1.
    part shows optional featureNandRdistributing wires are in same condition and applied OCR-II.
    2. In case of connecting the trip relay (OCR-II) Control power R+/R1-: AC110V, R+/R2-: AC220V common
    3. In case of connecting the trip relay (OCR-III) Control power R+/R2-: AC/DC110V220V common use, DC48V, DC24V (R1- contact is not provided)
    4. Please composeSelf maintenance circuitbecause alarm contact (AL1+/AL1-, AL2+/AL2-) is a instantaneous operating (under 15ms) type in case of using OCR-II.
    You may not composeSelf maintenance circuit, provided when OCR-III is using for a trip relay.
    5. Please input power to the MCB1, MCB2 of controller from the primary power.
    (If it is tripped OCR at the load part when power is connected, power will not be transfered automatically)
    6. Please connect the control power of trip relay (OCR-II. III) at the primary power section.
    7. According to this circuit drawing, ACB position isconnectedstandard, and ACB status is motor charged and tripped.

    41

    You might also like