Dog House

Dog House
A roof over the head of that four

legged family friend is often neglected.
Sun, rain, wind and snow can make
their life uncomfortable. But here is a
design for a simple A-Frame
shelter which is easy to put
together and could be
adapted for all sizes of dogs.
While the method of building this kennel is suitable
for all sizes, the measurements given would be
satisfactory only for a medium sized dog about 400
mm high.
If you wish to adjust the size to suit your dog,
remember that the dog should not only be able to
stand upright inside the hennel but should also be
able to turn around before he/she curls up and lies
down.
TOOLS YOU WILL

NEED
Hammer
Saws
Measuring
tape/rule
Carpenter's
square and
pencil
Adjustable
spanner
Drill and bits
60o/30o set
square
MATERIALS YOU WILL NEED

TIMBER (For example only)
HARDWARE
75 x 50mm, 6 pieces 1.2m* for two AFrames (use durable timber)
4/125 x 9mm Galvanise cup

head bolts, nuts, washers.
75 x 25mm, Decking, or equivalents, 16

pieces
100/50 x 2.8mm Galvanised

flat head nails.
1.2m* (for flooring)
75 x 75mm x 1.2m length of

zincalume angle as ridge
capping OR
1.2m length of aluminium
dampcourse.
Scandinavian Pine Cladding* in 1.2m

lengths (22 lengths should be sufficient for
overall height of wall/roof and the end
walls).
*Consult your TABMA merchant for
suitable available materials and how these
can be ordered.
12/12 x 3.2m Galvanised

round head, metal thread,
screws.
Features of the Dog House
CUT A-FRAME PIECES

From the 1.2m lengths of 75 x 50mm timber, cut four A-Frame legs (A) to this
pattern using the 60o/30o set square to mark the angles shown.
CUT FLOOR PLATE

From the remaining two lengths of 75 x 50mm pieces, cut two floor plates (B) to
pattern below, using the 60o/30o set square to mark the angles shown.
CUT TWO GUSSET PLATES

From a piece of Scandinavian Pine or other flat sheet material cut two gusset
plates (C) to the pattern below using the 60o/30o set square to mark the angles
shown.
ASSEMBLE A-FRAMES
Using two of the legs (A) cut in (1), and a floor (B) as in (2) and gusset plates
(C), assemble and fix components to make two A-Frames as in sketch below.
CUT FLOORING
From the flooring material cut two short boards for side pieces each 900mm long.
Cut two boards approx. 950mm cut remaining floor boards to 1200mm length
sufficient to cover the floor plate, allowing boards to be fixed closely together.
FIX FLOORING
(a) Select one of the assembled A-Frames an fix flooring square to floor
as shown in plan diagram using two nails at each board - pre-drilling nail
holes at end of board.
FIX FLOORING
(b) To the remaining A-Frame fix the floor boards to the floor plate as shown in diagram, similarly pre-drilling
nail holes at end of boards.
CUT AND FIX SIDE CLADDING

(I) Cut lengths of cladding to 1200mm lengths. Commencing with top of (A)
temporarily fix one board square to (A) legs allowing projection of approx.
100mm both front and back beyond A-Frame. Use two nails on each end of the
cladding piece (Note: spacing at top between frames should be exactly the same
as that at flooring level i.e. 900mm).
Sarking of building paper/heavy polythene is suggested. Fix this to

open side by stapling or light tacking with cut tacks or similar. Then
permanently fix a top cladding piece to this covered side, using two
nails each leg. To complete this sarked side, continue fixing cladding
sufficient to cover exposed ends of floor plates (B).
Remove temporary top cladding piece and fix sarking to second side.
Fix cladding to second side, as in (II) above.
(Note: Allow sarking to slightly sag between frames and extend well over the edges of the outer floor boards).
CUT AND FIX END CLADDING

Cut first piece of end cladding to shape given for gusset plate (Step 3). Then continue cutting cladding pieces
as required in diagram (See Step 10).
FIX FRONT CLADDING

Fix at least two pieces of angle cut cladding to front of structure. This could be
increased so as to reduce height of door, depending on size of dog.
FIX REAR CLADDING

Loosely fix shaped piece of selected sarking to outside end frame, so as to drape
outside edges of flooring. Commencing with topmost piece, cut and nail fix
sufficient cladding to cover exposed ends of decking floor. Allow clearance
between end cladding and ground line of at least 50mm.
CUT OFF, SAND OR SMOOTH

Cut off, sand or smooth to common line the exposed ends of cladding, similarly
round off and smooth projecting floor boards.
PRIME COAT DOG KENNEL

Apply recommended prime coat(s) of selected coating system to exposed timbers
including under flooring.
CUT AND FIX RIDGE CAPPING

Cut 1200mm length of selected ridge capping. Fix to ridge using zinc plated,
round head, self tapping metal thread screws in pre-drilled holes. Prime coat
ridge capping.
COMPLETE PAINTING
Apply final coats of selected paint/stain finish and allow several days to
thoroughly dry and all odours to evaporate before introducing dog to new
residence.
LOCATING DOG KENNEL
Locate dog kennel so that the doorway is protected from the worst of the
rainy/windy weather. Place legs so that the floor would slightly slope own towards
the doorway. We suggest you put legs on bricks rather than on grass or soil.
OTHER SIZE DOG KENNELS

The size of the dog kennel can be increased to fit your dog by using longer legs to
the A-Frame and longer floor plates. However retain the angles of 60o/30o where
indicated on frames and on the end cladding.

Dog House

Uploaded by

Copyright:

Available Formats

Dog House

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Dog House

Uploaded by

Copyright:

Available Formats

Dog House

A roof over the head of that four

TOOLS YOU WILL

MATERIALS YOU WILL NEED

75 x 50mm, 6 pieces 1.2m* for two AFrames (use durable timber)

4/125 x 9mm Galvanise cup

75 x 25mm, Decking, or equivalents, 16

100/50 x 2.8mm Galvanised

1.2m* (for flooring)

75 x 75mm x 1.2m length of

Scandinavian Pine Cladding* in 1.2m

12/12 x 3.2m Galvanised

Features of the Dog House

CUT A-FRAME PIECES

CUT FLOOR PLATE

CUT TWO GUSSET PLATES

CUT AND FIX SIDE CLADDING

Sarking of building paper/heavy polythene is suggested. Fix this to

CUT AND FIX END CLADDING

FIX FRONT CLADDING

FIX REAR CLADDING

CUT OFF, SAND OR SMOOTH

PRIME COAT DOG KENNEL

CUT AND FIX RIDGE CAPPING

LOCATING DOG KENNEL

OTHER SIZE DOG KENNELS

You might also like