Hitachi 42HDT79 Service Manual

PA No.
0217
42HDX99/DW2-U
42HDT79/DW2-U
SERVICE MANUAL 42HDS69/DW2-U
NTSC DW 2-U R/C: CLU-4352UG2 42HDS69

R/C: CLU-3861WL 42HDT79/42HDX99
ATSC Chassis
SERVICE MANUAL REVISION HISTORY INFORMATION

DATE REVISON # REASON
Apr , 28 SM00001 FIRST ISSUE OF MANUAL
09.27.06 CH 1 Part Numbers Changed
02.06.07 CH 2 Change 1 updated part description information
02.22.07 CH 3 Revised Service Menu sequence on pages 44 and 45

(FACT RESET >< MEMORY INIT)
04.19.07 CH 4 Updated part number information link
05.03.07 CH 5 Changed text, Increase > Decrease
SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT
PLASMA DISPLAY PANEL

APRIL 2006 HHEA-MANUFACTURING DIVISION
PA No. 0217
42HDX99/DW2-U
42HDT79/DW2-U
SERVICE MANUAL 42HDS69/DW2-U
NTSC P
DD W1
2 -U R/C: CLU-4352UG2 42HDS69
ATSC R/C: CLU-3861WL 42HDT79/42HDX99
AC hassis
TO GO TO A CHAPTER, CLICK ON ITS HEADING BELOW
CONTENTS
SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
PRODUCT SAFETY NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
SERVICING PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
AGENCY REGULATORY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
ACKNOWLEDGMENTS AND TRADEMARKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
BASIC SETUP & OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
TROUBLESHOOTING FLOWCHARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
BLOCK DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
CONNECTION DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
FINAL WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
QUICK DISASSEMBLY GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
FINAL ASSEMBLY GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
WAVEFORMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
DC VOLTAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
CIRCUIT SCHEMATIC DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
PRINTED CIRCUIT BOARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
QUICK REFERENCE PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of
electric shock do not perform any servicing other than that contained in the operating instructions
unless you are qualified to do so. Before servicing this chassis, it is important that the service
technician read the “IMPORTANT SAFETY INSTRUCTIONS” in this service manual.
SAFETY NOTICE
USE ISOLATION TRANSFORMER WHEN SERVICING
Components having special safety characteristics are identified by a ! on the schematics and on the parts list in this
Service Data and its supplements and bulletins. Before servicing the chassis, it is important that the service technician
read and follow the “Important Safety Instructions” in this Service Manual.
SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT
PLASMA DISPLAY PANEL

APRIL 2006 HHEA-MANUFACTURING DIVISION
DW2U
SAFETY PRECAUTIONS
NOTICE: Comply with all cautions and safety-related notes Leakage Current Hot Check
located on or inside the cover case and on the chassis or plasma Plug the AC line cord directly into a 120V AC outlet. (Do not use an
module. isolation transformer during this test.) Use a leakage current
WARNING: Since the chassis of this receiver is connected to tester or a metering system that complies with the American
one side of the AC power supply during operation, whenever the National Standards Institute (ANSI) C101.0 Leakage Current
receiver is plugged in service should not be attempted by any- for Appliances. In the case of the PDP monitor set the AC
one unfamiliar with the precautions necessary when working on switch first in the ON position and then in the OFF position,
this type of receiver. measure from across Line 1 and Line 2 of the three plug
prongs, do not connect with the third prong, which is physical
1. When service is required, an isolation transformer should be ground, to all exposed metal parts of the instrument
inserted between power line and the receiver before any (antennas, handle bracket, metal cabinet, screw heads,
service is performed on a “HOT” chassis receiver. metallic overlays, control shafts, etc.), especially any exposed
metal parts that offer an electrical return path to the chassis.
2. When replacing a chassis in the receiver, all the protective Any current measured must not exceed 0.5 MIU. Reverse the
devices must be put back in place, such as barriers, non- instrument power cord plug in the outlet and repeat test.
metallic knobs, insulating cover-shields, and isolation
resistors, capacitors, etc.
3. When service is required, observe the original lead dress.

AC LEAKAGE TEST
4. Always use manufacturer’s replacement components. Critical
components as indicated on the circuit diagram should not be (READING
replaced by another manufacturer’s. Furthermore, where a SHOULD NOT
LEAKAGE BE ABOVE 0.5MIU)
short circuit has occurred, replace those components that CURRENT
indicate evidence of over heating. DEVICE TESTER
UNDER
5. Before returning a serviced receiver to the customer, the TEST
service technician must thoroughly test the unit to be certain TEST ALL
EXPOSED
that it is completely safe to operate without danger of electrical METAL SURFACES
shock, and be sure that no protective device built into the EARTH
3-WIRE CORD
receiver by the manufacturer has become defective, or GROUND
inadvertently defeated during servicing. ALSO TEST WITH PLUG
REVERSED
Therefore, the following checks should be performed for the (USING AC ADAPTER
PLUS AS REQUIRED)
continued protection of the customer and service technician.
Leakage Current Cold Check ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED
With the AC plug removed from the 120V AC 60Hz source, ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD
place a jumper across Line 1 and Line 2 of the three plug AND MUST BE CORRECTED BEFORE RETURNING THE
prongs, do not connect with the third prong, which is physical RECEIVER TO THE CUSTOMER.
ground.
Using an insulation tester (DC500V), connect one of its leads
to the AC plug jumper and touch with the other lead each
exposed metal part (antennas, screwheads, metal overlays,
control shafts, etc.), particularly any exposed metal part
having a return path to the chassis should have a resistor
reading over 4MΩ. Any resistance value below this range
indicates an abnormality which requires corrective action. An
exposed metal part not having a return path to the chassis will
indicate an open circuit.
2
TABLE OF CONTENTS
DW2U
PRODUCT SAFETY NOTICE

Many electrical and mechanical parts in HITACHI television PDP Module Handling
receivers have special safety-related characteristics. These are
often not evident from visual inspection nor can the protection When there is need to replace a broken PDP module which is the
afforded by them necessarily be obtained by using replacement displaying device from the Plasma monitor unit, consider the
components rated for higher voltage, wattage, etc. Replacement following:
parts which have these special safety characteristics are
identified in this Service Manual. 1. When carrying the PDP module, two persons should stand at
both shorter-edge sides of the glass-panel and transport it with
Electrical components having such features are identified with a their palms. Avoid touching the Flexible Printed Circuits or the
! mark in the schematics and parts list in this Service Manual. chip tube on the corner of the glass-panel. Handle only by the
surface of the glass panel. In case of some PDP modules,
The use of a substitute replacement component which does not electrode repair is done by connecting between regular
have the same safety characteristics as the HITACHI- terminal with Cu tape and Cu wire. Please do not hook and/or
recommended replacement component, shown in the parts list in damage this repair line. If it is damaged, the module will not
this Service Manual, may create shock, fire, X-radiation, or other function unless the glass-panel is exchanged with a new
hazards. glass-panel.
2. When carrying PDP module, watch surrounding objects, such
Product safety is continuously under review and new instructions as tables, and also do not carry it alone since it may be
are issued from time to time. For the latest information, always dangerous and it will be damaged due to excessive stress to
consult the current HITACHI Service Manual. A subscription to, the module (glass-panel).
or additional copies of HITACHI Service Manuals may be 3. Please do not stand the module with the edge of the glass-
obtained at a nominal charge from HITACHI Sales Corporation. panel on the table since this might result in damage to the
glass-panel and/or flexible printed circuits due to excessive
stress to the module (glass-panel).
1. Follow the general caution recommendations from “Safety WARNING

precautions” section. Lead in solder used in this product is listed by the California
Health and Welfare agency as a known reproductive toxicant
42HDS69/HDT79/HDX99 - Plasma Monitor Unit which may cause birth defects or other reproductive harm
55HDS69/HDT79/HDX99 - Plasma Monitor Unit (California Health and Safety Code, Section 25249.5).
1. Follow the general caution recommendations from “Safety When servicing or handling circuit boards and other components
precautions” section. which contain lead in solder, avoid unprotected skin contact with
2. Since the Panel module and front filter are made of glass, solder. Also, when soldering make sure you are in a well
sufficient care shall be taken when handling the broken ventilated area in order to avoid inhalation of any smoke or
module and filter in order to avoid injury. fumes released.
3. If necessary to replace Panel module, this work must be
started after the panel module and the AC/DC Power supply SAFETY NOTICE
becomes sufficiently cool. USE ISOLATION TRANSFORMER
4. Special care must be taken with the display area to avoid WHEN SERVICING
damaging its surface.
5. The Panel Module shall not be touched with bare hands to POWER SOURCE
protect its surface from stains.
6. It is recommended to use clean soft gloves during the This plasma television is designed to operate on 120 Volts
replacing work of the Panel module in order to protect, not 60Hz, AC house current. Insert the power cord into a 120 Volts
only the display area of the panel module but also the 60Hz outlet.
serviceman.
7. The Chip Tube of the panel module (located upper left of the NEVER CONNECT THE PLASMA TELEVISION TO OTHER
back of the panel module) and flexible cables connecting THAN THE SPECIFIED VOLTAGE OR TO DIRECT CURRENT
Panel glasses to the drive circuitry Printed Wiring Boards AND TO 50HZ. TO PREVENT ELECTRIC SHOCK, DO NOT
(P.W.B.) are very weak, so sufficient care must be taken to USE THE PLASMA TELEVISION’S (POLARIZED) PLUG WITH
prevent breaking or cutting any of these. If the Chip Tube AN EXTENSION CORD, RECEPTACLE, OR THE OUTLETS
breaks the panel module will never work, replacement for a UNLESS THE BLADES AND GROUND TERMINAL CAN BE
new plasma panel module will be needed. FULLY UNSERTED TO PREVENT BLADE EXPOSURE.
8. AV Digital Block, power supply and PDP driving circuit
P.W.B.’s are assembled on the rear side of the PDP module,
take special care with this fragile circuitry; particularly, Flexible
Printed Circuits bonded to surrounding edges of the glass
panel. They are not strong enough to withstand harsh outer
mechanical forces. Avoid touching the flexible printed circuits
by not only your hands, but also tools, chassis, or any other
object. Extreme bending of the connectors must be avoided
too. In case the flexible printed circuits are damaged, the
corresponding addressed portions of the screen will not be lit
and exchange of a glass panel will be required.
3
TABLE OF CONTENTS
DW2U
SERVICING PRECAUTIONS
CAUTION: Before servicing instruments covered by this Electrostatically Sensitive (ES) Devices
service data and its supplements and addenda, read and Some semiconductor (solid state) devices can be damaged
follow the “Important Safety Instructions” on page 3 of this easily by static electricity. Such components commonly are
publication. called Electrostatically Sensitive (ES) Devices. Examples of
NOTE: If unforeseen circumstances create conflict between typical ES devices are integrated circuits and some field-
the following servicing precautions and any of the safety effect transistors and semiconductor “chip” components. The
precautions on page 3 of this publication, always follow the following techniques should be used to help reduce the
safety precautions. Remember: Safety First. incidence of component damage caused by static electricity.
General Servicing Guidelines 1. Immediately before handling any semiconductor

1. Always unplug the instrument AC power cord from the AC component or semiconductor-equipped assembly, drain
power source before: off any electrostatic charge on your body by touching a
a. Removing or reinstalling any component, circuit known earth ground. Alternatively, obtain and wear a
board, module, or any other instrument assembly. commercially available discharging wrist strap device,
which should be removed for potential shock reasons
b. Disconnecting or reconnecting any instrument prior to applying power to the unit under test.
electrical plug or other electrical connection.
2. After removing an electrical assembly equipped with ES
c. Connecting a test substitute in parallel with an devices, place the assembly on a conductive surface
electrolytic capacitor in the instrument. such as aluminum foil, to prevent electrostatic charge
buildup or exposure of the assembly.
CAUTION: A wrong part substitution or incorrect
polarity installation of electrolytic 3. Use only a grounded-tip soldering iron to solder or
capacitors may result in an explosion desolder ES devices.
hazard.
4. Use only an anti-static type solder removal device. Some
2. Do not spray chemicals on or near this instrument or any solder removal devices not classified as “anti-static” can
of its assemblies. generate electrical charges sufficient to damage ES
device.
3. Unless specified otherwise in these service data, clean
electrical contacts by applying the following mixture to the 5. Do not use freon-propelled chemicals. These can
contacts with a pipe cleaner, cotton-tipped stick or generate electrical charges sufficient to damage ES
comparable nonabrasive applicator: 10% (by volume) devices.
Acetone and 90% (by volume) isopropyl alcohol (90%-
99% strength). 6. Do not remove a replacement ES device from its
CAUTION: This is a flammable mixture. Unless protective package until immediately before you are
specified otherwise in these service data, ready to install it. (Most replacement ES devices are
lubrication of contacts is not required. packaged with leads electrically shorted together by
conductive foam, aluminum foil or comparable conductive
4. Do not defeat any plug/socket of voltage interlocks with material.)
which instruments covered by this service data might be
equipped. 7. Immediately before removing the protective material from
the leads of a replacement ES device, touch the
5. Do not apply AC power to this instrument and/or any of its protective material to the chassis or circuit assembly into
electrical assemblies unless all solid-state device heat- which the device will be installed.
sinks are correctly installed. CAUTION: Be sure no power is applied to the chassis or
circuit, and observe all other safety
6. Always connect the test instrument ground lead to the precautions.
appropriate instrument chassis ground before connecting
the test instrument positive lead. Always remove the test 8. Minimize bodily motions when handling unpackaged
instrument ground lead last. replacement ES devices. (Otherwise harmless motion
such as the brushing together of your clothes fabric or the
7. Use with this instrument only the test fixtures specified in lifting of your foot from a carpeted floor can generate
this service data. static electricity sufficient to damage an ES device.)
CAUTION: Do not connect the test fixture ground strap
to any heatsink in this instrument.
4
TABLE OF CONTENTS
DW2U
General Soldering Guidelines Removal

1. Use a grounded-tip, low-wattage soldering iron and 1. Desolder and straighten each IC lead in one operation by
appropriate tip size and shape that will maintain tip gently prying up on the lead with the soldering iron tip as
temperature within the range 500°F to 600°F. the solder melts.
2. Use an appropriate lead free solder (see page 8). Lead 2. Draw away the melted solder with an anti-static suction-
solder can be used, but there is a possibility of failure due type solder removal device (or with solder braid) before
to insufficient strength of the solder. removing the IC.
3. Keep the soldering iron tip clean and well-tinned. Replacement

1. Carefully insert the replacement IC in the circuit board.
4. Thoroughly clean the surfaces to be soldered. Use a
small wire-bristle (0.5 inch or 1.25 cm) brush with a metal 2. Carefully bend each IC lead against the circuit foil pad
handle. Do not use freon-propelled spray-on cleaners. and solder it.
5. Use the following desoldering technique. 3. Clean the soldered areas with a small wire-bristle brush.
a. Allow the soldering iron tip to reach normal (It is not necessary to reapply acrylic coating to areas.)
temperature (500°F to 600°F).
“Small-signal” Discrete Transistor Removal/Replacement
b. Heat the component lead until the solder melts. 1. Remove the defective transistor by clipping its leads as
Quickly draw away the melted solder with an anti- close as possible to the component body.
static, suction-type solder removal device or with
solder braid. 2. Bend into a “U” shape the end of each of the three leads
CAUTION: Work quickly to avoid overheating the remaining on the circuit board.
circuit board printed foil.
3. Bend into a “U” shape the replacement transistor leads.
6. Use the following soldering technique.
a. Allow the soldering iron tip to reach normal 4. Connect the replacement transistor leads to the
temperature (500°F to 600°F). corresponding leads extending from the circuit board and
crimp the “U” with long nose pliers to insure metal to
b. First, hold the soldering iron tip and solder strand metal contact, then solder each connection.
against the component lead until the solder melts.
Power Output Transistor Devices Removal/Replacements
c. Quickly move the soldering iron tip to the junction of 1. Heat and remove all solder from around the transistor
the component lead and the printed circuit foil, and leads.
hold it there only until the solder flows onto and
around both the component lead and the foil. 2. Remove the heatsink mounting screw (if so equipped).
CAUTION: Work quickly to avoid overheating the
circuit board printed foil or components. 3. Carefully remove the transistor from the circuit board.
d. Closely inspect the solder area and remove any 4. Insert new transistor in circuit board.
excess or splashed solder with a small wire-bristle
brush. 5. Solder each transistor lead, and clip off excess lead.
6. Replace heatsink.
Diode Removal/Replacement
1. Remove defective diode by clipping its leads as close as
possible to diode body.
2. Bend the two remaining leads perpendicularly to the

circuit board.
3. Observing diode polarity, wrap each lead of the new

diode around the corresponding lead on the circuit board.
Use Soldering Iron to Pry Leads
4. Securely crimp each connection and solder it.
IC Removal/Replacement 5. Inspect (on the circuit board copper side) the solder joints
Some Hitachi unitized chassis circuit boards have slotted of the two “original leads”. If they are not shiny, reheat
holes (oblong) through which the IC leads are inserted and them and, if necessary, apply additional solder.
then bent flat against the circuit foil. When holes are the
slotted type, the following technique should be used to
remove and replace the IC. When working with boards using
the familiar round hole, use the standard technique as
outlined in paragraphs 5 and 6 above.
5
DW2U
Fuses and Conventional Resistor Removal/Replacement At Other Connections

1. Clip each fuse or resistor lead at top of circuit board Use the following technique to repair defective copper
hollow stake. pattern at connections other than IC Pins. This technique
involves the installation of a jumper wire on the component
2. Securely crimp leads of replacement component around side of the circuit board.
stake 1/8 inch from top.
3. Solder the connections.

CAUTION: Maintain original spacing between the
replaced component and adjacent
components and the circuit board, to
prevent excessive component
temperatures. DEFECTIVE
COPPER
Circuit Board Foil Repair REMOVED
Excessive heat applied to the copper foil of any printed
circuit board will weaken the adhesive that bonds the foil to
the circuit board, causing the foil to separate from, or “lift-
off,” the board. The following guidelines and procedures
should be followed whenever this condition is encountered.
In Critical Copper Pattern Areas Insulated Jumper Wire

High component/copper pattern density and/or special
voltage/current characteristics make the spacing and 1. Remove the defective copper pattern with a sharp knife.
integrity of copper pattern in some circuit board areas more Remove at least 1/4 inch of copper, to ensure hazardous
critical than in others. The circuit foil in these areas is condition will not exist if the jumper wire opens.
designated as Critical Copper Pattern. Because Critical
Copper Pattern requires special soldering techniques to 2. Trace along the copper pattern from both wire sides of
ensure the maintenance of reliability and safety standards, the pattern break and locate the nearest component
contact your Hitachi personnel. directly connected to the affected copper pattern.
At IC Connections 3. Connect insulated 20-gauge jumper wire from the

To repair defective copper pattern at IC connections, use the nearest component on one side of the pattern break to
following procedure to install a jumper wire on the copper the lead of the nearest component on the other side.
pattern side of the circuit board. (Use this technique only on Carefully crimp and solder the connections.
IC connections.) CAUTION: Be sure the insulated jumper wire is
1. Carefully remove the damaged copper pattern with a dressed so that it does not touch
sharp knife. (Remove only as much copper as absolutely components or sharp edges.
necessary.)
2. Carefully scratch away the solder resist and acrylic

coating (if used) from the end of the remaining copper
pattern.
BARE JUMPER
WIRE
CRIMP AND
SOLDER
Install Jumper Wire and Solder
3. Bend a small “U” in one end of a small-gauge jumper wire

and carefully crimp it around the IC pin. Solder the IC
connection.
4. Route the jumper wire along the path of the cut-away

copper pattern and let it overlap the previously scraped
end of the good copper pattern. Solder the overlapped
area, and clip off any excess jumper wire.
6
DW2U
NOTE: These components are affixed with glue. Be careful not to break or damage any foil under the
component or at the pins of the ICs when removing. Usually applying heat to the component for a short
time while twisting with tweezers will break the component loose.
Leadless Chip Components How to Replace Flat-lC

(surface mount) —Required Tools—
Chip components must be replaced with identical • Soldering iron • iron wire or small awl
chips due to critical foil track spacing. There are no • De-solder braids • Magnifier
holes in the board to mount standard transistors or 1. Remove the solder from all of the pins of a Flat-lC
diodes. Some chip capacitor or resistor board solder by using a de-solder braid.
pads may have holes through the board, however the
hole diameter limits standard resistor replacement to De-Solder
1/8 watt. Standard capacitors may also be limited for Braid
the same reason. It is recommended that identical
chip components be used. . Soldering
Iron
Chip resistors have a three digit numerical resistance
code -1st and 2nd significant digits and a multiplier. 2. Put the iron wire under the pins of the Flat-lC and
Example: 162 = 1600 or 1.6KΩ resistor, 0 = 0Ω pull it in the direction indicated while heating the
(jumper). pins using a soldering iron. A small awl can be
Chip capacitors generally do not have the value used instead of the iron wire.
Iron
indicated on the capacitor. The color of the component Wire
indicates the general range of the capacitance. Awl
Chip transistors are identified by a two letter code. The
first letter indicates the type and the second letter, the
grade of transistor. Soldering
Chip diodes have a two letter identification code as Pull Soldering Iron
Iron
per the code chart and are a dual diode pack with
either 3. Remove the solder from all of the pads of the
common anode or common cathode. Check the parts Fiat-lC by using
list for correct diode number. a de-solder braid. Soldering
Iron
Component Removal
1. Use solder wick to remove solder from component De-Solder
end caps or terminals. Braid
2. Without pulling up, carefully twist the component
with tweezers to break the adhesive. Flat-IC
3. Do not reuse removed leadless or chip
components since they are subject to stress 4. Position the new Flat-lC in place (apply the pins of
fracture during removal . the Flat-lC to the soldering pads where the pins
Chip Component Installation need to be soldered). Properly Polarity Symbol
determine the positions of the
1. Put a small amount of solder on the board soldering pads and pins by
soldering pads. correctly aligning the polarity
2. Hold the chip component against the soldering symbol.
pads with tweezers or with a miniature alligator
clip and apply heat to the pad area with a 30 watt
iron until solder flows. Do not apply heat for more 5. Solder all pins to the soldering pads using a fine
than 3 seconds tipped soldering iron.
Chip Components
TYPE
C GRADE SOLDER
CAPS
B Solder Soldering
TRANSISTOR CAPACITOR Iron
E
1ST DIGIT
6. Check with a magnifier for solder bridge between
2ND DIGIT
COMMON CATHODE the pins or for dry joint between pins and soldering
MULTIPLIER pads. To remove a solder bridge, use a de-solder
= 1600 = 1.6K braid as shown in the figure below.
De-Solder
ANODES SOLDER CAPS Braid
MH DIODE RESISTOR
Bridge Soldering
Solder Iron
7
DW2U
Information for service about lead-free solder introduction

Hitachi introduced lead-free solder to conserve the "Earth Environment".
Please refer to the following before servicing.
(1) Characteristic of lead-free solder

Melting point of lead free solder is 40-50oC higher than solder containing lead.
(2) Solder for service

Following composition is recommended.
" Sn - 3.0Ag - 0.5Cu " , or " Sn - 0.7 Cu "
Lead solder can be used, but there is a possibility of failure due to insufficient strength of the solder.
Caution when using solder containing lead.

Please remove previous solder as much as possible from the soldering point.
When soldering, please perfectly melt the lead-free solder to mix well with the previous solder.
(3) Soldering iron for lead-free solder.

Melting point of lead-free solder is higher than solder containing lead.
Use of a soldering tool "with temperature control" and "with much thermal capacitance" is recommended.
(Recommended temperature control : 320oC - 450oC)
Recommended temperature
PWB with chip parts 320oC +/- 30oC
PWB without chip parts 380oC +/- 30oC
Chassis, metal, shield etc. 420oC +/- 30oC
(4) Identification of lead-free PWB
2004 models >> lead-free solder is introduced

2006 models >> lead-free solder apply
On lead-free PWB, "F" is added at the beginning of stamp on PWB. (e.g. DW2-POD F)
8
DW2U
AGENCY REGULATORY
INFORMATION
Federal Communications Commission Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
FCC Information
This device complies with part15 of the FCC Rules.Operation is subject to the following two conditions :
(1) This decide may not cause harmful interference and (2) This decide must accept any interference
received, including interference that may cause undesired operation.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not
expressly approved by Hitachi America ,Ltd. Home Electronics Division may void the user’s authority to
operate the equipment.
Cables
Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to
maintain compliance with FCC Rules and Regulations.
Any cables that are supplied with the system must be replaced with identical cables in order to assure
compliance with FCC rules. Order Hitachi spares as replacement cables.
Note
This Plasma Television receiver will display television closed captioning, ( or ), in accordance with
paragraph 15.119 of the FCC rules.
INDUSTRY CANADA AGENCY REGULATORY INFORMATION

Cable Compatible Television Apparatus- Tèlèvision câblocompatible, Canada.
In the United States, TV GUIDE and other related marks are registered marks of Gemstar-TV Guide International,
Inc. and/or one of its affiliates. In Canada, TV GUIDE is a registered mark of Transcontinental Inc., and is used
under license by Gemstar-TV Guide International, Inc.
The TV Guide On Screen system is manufactured under license from Gemstar-TV Guide International, Inc.
and/or one of its affiliates.
The TV Guide On Screen system is protected by one or more of the following issued United States patents
6,498,895; 6,418,556; 6,331,877; 6,239,794; 6,154,203; 5,940,073; 4,908,713; 4,751,578; 4,706,121.
Gemstar-TV Guide International Inc. and/or its related affiliates are not in any way liable for the accuracy or
availability of the program schedule information or other data in the TV Guide On Screen system and cannot
guarantee service availability in your area. In no event shall Gemstar-TV Guide International, Inc. and/or its
related affiliates be liable for any damages in connection with the accuracy or availability of the program
schedule information or other data in the TV Guide On Screen system.
9
TABLE OF CONTENTS
DW2U
ACKNOWLEDGMENTS
AND TRADEMARKS
This Plasma Television complies with VESA DDC2B specifications, Plug & Play
is a system with computer, peripherals (including monitors) and operating
system. It works when the monitor is connected to a DDC ready computer that
is running an operating system software that is capable for the plug & play.
When a Plug and Play PC is powered on, it sends a command to the Monitor
requesting identification. The Monitor sends back a string of data including its
characteristics.
TRADEMARK ACKNOWLEDGMENT
DDCTM is a trademark of Video Electronics Standard Association.
IBM PC/AT and VGA are registered trademarkds of International Business Machines Corporation of the U.S.A.
Apple and Macintosh are registered trademarks of Apple Computer, Inc.
VESA is a trademark of a nonprofit organization, Video Electronics Standard Association.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Cable Compatible Television Apparatus- Tèlèvision câblocompatible, Canada.
Notes on Closed Caption:

This Plasma Television receiver will display television closed captioning, ( or ), in accordance with
paragraph 15.119 of the FCC rules.
*Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
In the U.S. , TV GUIDE and other related marks are registered marks of Gemstar-TV Guide International, Inc. and/or
one of its affiliates. In Canada , TV GUIDE is a registered of transcontinental Inc. , and is used under license by Gemstar-TV
Guide International, Inc.
10
TABLE OF CONTENTS
DW2U
INTRODUCTION
The Digital AV Block is inside of the Panel assembly controls most of the user functions of the complete TV set and conditions the signal
to the plasma panel.
The 42” and 55” monitors contain the displaying device, which is the plasma display panel module, and the driving circuitry, which
receives the signal from the Digital AV Block and after processing, delivers the image to the display module.
This HITACHI Service Manual is intended for the qualified service personnel and it contains the necessary information for
troubleshooting the Plasma television set in case of malfunction.
DIMENSIONS:
42HDS69/HDT79/HDX99
108.5 mm
1134 mm
17 mm 90.5 mm
104 mm 104 mm
526.6 mm
926 mm
713.2 mm
648 mm
328 mm
393.2 mm
485.3 mm 365 mm
POWER RATINGS:
Indicated Value PST(W)

Max Rating Average Without POD. With POD.
No. Model Name (W) (A) Rating (W) less than 1W less than 14W Chassis
1 42HDS69/HDT79 370W 3.4A 236W 0.6W 14W DW-2U
42HDX99
CIRCUIT PROTECTION
CAUTION: Below is an EXAMPLE only. See Replacement Parts List for details. The following symbol near the fuse
indicates fast operation fuse (to be replaced). Fuse ratings appear within the symbol.
Example:
6.3 A
F
125V
6.3 A 125V
The rating of fuse F9A2 is 6.3 A - 125V.
Replace with the same type fuse for continued protection
“RISK OF FIRE - REPLACE FUSE AS MARKED”
against fire.
11
TABLE OF CONTENTS
DW2U
SPECIFICATIONS
FEATURES
A- Plasma
Model 42HDS69/42HDT79/42HDX99
Dimension Size 1 1134mm x 713.2mm x 365mm

Weight 2 39.8k g
A/C Input Input AC Voltage 3 AC108V~132V (with 3 Plug AC Power Cord i nlet
Voltage type ,1.8m length)
Input AC Frequency 4 60Hz
Power Consumption 5 370W, SBY/POD -SBY less than 1W/14W
Front End Front End(NTSC & ATSC) 6 ENGD6305
NTSC/ATSC(8VSB),64QAM,256QAM)
Available Channel 7 2~13 VHP
8 14 ~ 69 UHF
9 A-5~A-1,A~W,W+1~W+94 CATV
Input Signal Video Signal 10 N T S C
Component Signal 11 4 8 0 i / p . 1 0 8 0 i , 7 2 0 p
PC Signal 12 V G A - U X G A fH:24KHz -1 09KHz,fV:50Hz-
85Hz)
HDMI Signal 13 480i,480p,720p,1080i(EIA-861B) 3
Picture Y/C Separation 14 3D Y/C (ON fix)
Line Correction 15 No
I-P Conversion 16 Motion Adaptive & Multi Angle Interpolation FC6
Picture Mode 17 Day.Night
Display Mode 18 42:1024i,55:768p Video Signal
19 42:1024i,55:768p ComponentSignal
20 42:1024i,55:768p PinP Mode
21 -
Sound Enhancement 22 BassBoost & Surround (Normal, Wide, Off)
Adjustment Settings for Video Signal 23 Picture,Contrast,Brightness,Color,Tint , Sharpness,

W/B Temp.Black Enhancement .Contrast Mode.Color
Management/Decoding ,Auto Color.Noise
Reductfon.Auto Movie Mode, .Black Side Panel
Settings for Sound 24 Vol, Balance, Bass.Treble, Source, Internal Speakers

,Auto Noise Cancel.Perfect Volume.Mute.Soft Mute
25
26
General PinP Split 27 With(ANT/CABLE DIGITAL CHANNEL & Video.480i ,720p,1080i) Except Photo Input only HDT/HDX
Function Mode Strobe 28 With(3Pix:only ANT/CABLE DIGITAL CHANNEL,Video,480i) Except Photo Input only HDT/HDX
29
POP 30 With Main: ANT/CABLE DIGITAL CHANNEL,Video.480i ,720p,1080i) Except Photo Input only HDT/HDX
PIP 31 With(Main:ANT/CABLE DIGITAL CHANNEL,Video.480i ,720p,1080i) Except Photo Input only HDT/HDX
Freeze 32 With(3Pix:only ANT/CABLE DIGITAL CHANNEL,Video,480i) Except Photo Input only HDT/HDX
Wide Mode 33 7Mode
Aspect Video Selection 34 4:3 Standard/16:9 Standard1 /16:9 Standard 2
4:3 Expanded/Zoom1/Zoom 2/16:9 Zoom
PC 35 Full/Normal/Real (Real
42:VGA,55:VGA/SVGA/XGA/WXGA)
Film Theater 36 With(Auto Movie Mode:On/Off)
Color Temperature 37 4Mode (High/Medium/Standard/Black & White) Black & White only HDT/HDX
Input Signal Selection 38 VIDEO1/2/3/4/5, Cable/ Air,IEEE1394,Photo IEEE1394 only HDT/HDX
Input Photo Input only HDT/HDX
12
TABLE OF CONTENTS
DW2U
SPECIFICATIONS
FEATURES
Model 42HDS69/42HDT79/42HDX99
General Gamma Correction 39 Only for Service Menu
Function Picture Enhancer 40 -
Input Signal Identification 41 yes
Audio Special Mode 42 No
Power Save Mode 43 With (On/Off) (Video In) LED Normal: Blue
44 Power Save: Orange
Stand by: Red
Burning Protection 45 With (Raster Shift:3 option.AII White Pattern)
OSD Language (VIDEO) 46 ENGLISH.FRANCAIS.ESPANOL
Power Swivel 47 With 42HDT79 and 42HDX99 only
R/C Handset 48 CLU -3861WL/CLU-123S /CLU-4352UG2 P A N A S O N I C / UEI/HOSHIDEN
In/Out 49
Terminal Composite Video Input 50 5 Input: RCA pin* 5 (1 Input Side Panel)
(VIDEO1~5)
S-ln(S2 Terminal) (Video/S are 51 2 InputMini Din-4P x 2

common selector, priority is S-ln) .
Component Signal Input 52 3 lnput:RCA pin x 9(Y of VIDEO1/2/5 is common

(VIDEO3.VIDEO4.VIDEO5) input for Composite-In)
Digital Input(HDMH-HDCP) 53 3 lnput:HDMI(18P)X3 (Selected by component
Video1/2/5.Digital input priority)
Audio In (L/R) (Lch:mono) 54 5 lnput:RCApinx10
Auto Link 55 1 Input (VIDEO2 LINK) Auto Link Function

Video Control Terminal (BS) 56 No
U/V Ant Input 57 CABLE / AIR
BS-I/F Input 58 No
Video Monitor Out Terminal 59 1 Output: RCA pin x 1
Audio Output Terminal 60 1 O u t p u t U R : R C A p i n x 2( Common input for No.59 )
Audio Monitor Out Terminal 61 1 Output L/R:RCA pin x 2

IR-OUTPUT 62 2 Terminal 42HDT79/42HDX99 Only
Headphone Terminal 63 No
64
IEEE 1394 Input 65 2 (4pin connector) 42HDX99 Only
RS-232C Terminal 66 1 (Female type)
Photo Input 67 1 (On Side panel) 42HDT79/42HDX99 Only
Audio Optical Output 68 1 (Square type)
Front Main Power Switch 69 Yes , below panel
Key Power On/off Switch 70 Yes, on side panel
IR Receiving Unit 71 Yes, on front panel
Power Indicator LED 72 Yes, on front panel
Menu Control Key 73 Yes, on side panel (Channel U/D, Vol U/D, A/V Input
Select , Menu Select)
Option POP TV Stand 74 With
Wall Mount Unit 75 With
76 -
13
DW2U
FEATURES & DIFFERENCES

QAM Basic
Model Name Class Chassis Series Cabinet Aspect ATSC ATSC/NTSC Digital POD MPEG EPG M/C
Name Design 1Tuner Cable Decoder Gemstar
42HDX99 HDX DW2C Directors Leggero(ALL BLK) 16x9 X X X X X X USB
42HDT79 HDT DW2B UltraVision Leggero(SP:BLK, DECO:SIL) 16x9 X X X X X X USB
42HDS69 HDS DW2A UltraVision Leggero(ALL SIL) 16x9 X X X X X - -
DTV Memory
Model Name Class NTSC Seine 3/2 Fill by Shield Comb Resolution OSD Color Temp
FORMAT Pulldown Mode inputs Filter
42HDX99 HDX 1080i Seine2 Auto/off 7modes X 31% sputter 3DYC A4웛1024x1080 06 OSD Dir 4Mode(High, Med,Std, B&W
42HDT79 HDT 1080i Seine2 Auto/off 7modes X 36% sputter 3DYC A4웛1024x1080 06 OSD A 3Mode(High, Med,Std)
42HDS69 HDS 1080i Seine2 Auto/off 7modes X 36% sputter 3DYC A4웛1024x1080 06 OSD B 3Mode(High, Med,Std)
Remote Sound function

Model Name Class PIP AV NET Type Source Simple IR Descrete Dolby Perfect Surround BassBoost
Color UEI Pass Thru Code Volume
42HDX99 HDX Digital Tuner/Ext SPLIT X Rotate PANA/Black X X X AC3 Downmix × × ×
42HDT79 HDT Digital Tuner/Ext SPLIT - Rotate PANA/Black - X X AC3 Downmix × × ×
42HDS69 HDS Digital Tuner/Ext SPLIT - TVU Hoshiden/BLACK - - X AC3 Downmix × × ×
Rear Jacks
Model Name Class TV Output Speaker Digital I/F RS232C IR-Out YPbPr S IN AV IN S V AUDIO Y As 6CH RF
Center Watt IEEE1394 HDMI(Ver1.1) OUT OUT OUPUT Composite OUT
42HDX99 HDX L/mono 36 2FR2W 1 2 1 2 2(1H,2H,2.14H) 2 4 1 1 1 X OPT 1
42HDT79 HDT L/mono 36 2FR2W - 2 1 2 2(1H,2H,2.14H) 2 4 1 1 1 X OPT 1
42HDS69 HDS L/mono 36 2FR2W - 2 1 - 2(1H,2H,2.14H) 2 4 1 1 1 X OPT 1
Front/Side Jack
Model Name Class HDMI
Composite L/R (Ver1.1) Y,Pb,Pr
42HDX99 HDX 1 1 1 1
42HDT79 HDT 1 1 1 1
42HDS69 HDS 1 1 1 1
Downloadable Option Swivel Table Top Hotel Adjust Color Contrast

Model Name Class Power V Chip Energy Star PLC Wall mount Pow/Manual Stand Mode Color Manage Mode
LED Decoder
42HDX99 HDX Blue X X X WM51 Pow × BLK(9000) × X X X
42HDT79 HDT Blue X X X WM51 Pow × SIL(9000) × X X X
42HDS69 HDS Blue X X X WM51 Manual × SIL(9000) × - - X
White Level
Model Name Class Black Level
42HDX99 HDX X
42HDT79 HDT -
42HDS69 HDS -
14
DW2U
General Specification
Model Spec Environment Specifications

Model Name Item 42HDS69/42HDT79/42HDX99 NO Item Specification
1 Operating Temp. +5°C~+35°C
Destination U.S.A. / CANADA 2 Stock Temp. -15°C~+60°C
Exterior Cabinet Dimensions
(Main Body) (Speaker & 1134mm x 713.2mm x 365mm 3 Operating Humidity 20%~80%RH
stand inclusive) 4 Stock Humidity 20%~90%RH
Frame Color Screen Dark Charcoal Metallic (HDT/HDX)
Brightness Silver (HDS) 5 Operating Atmosphere 800~1114h Pa
Inclusive (With Power Swivel)
Pressure
Stand (1888m~-757m)
Weight (Main Body)
(Speaker & stand 6 Stock Atmosphere Pressure 300~1114h P a
39.20 kg typ. 44.0 kg
inclusive)
(4727m~-757m)
(Main Body: Packed)
922x524mm(42lnch 16:9) 7 Warranty Gravity Vertical 0.85 G
Screen Size
Display Panel Resolution 1024x1080 pixels
8 Warranty Drop High 30cm
Dot Pitch (H) 0.90mm
Dot Pitch (V) 0.485mm 9 Tilt Angle 12° Over
Viewing Angle (H) ±85°
Viewing Angle (V) ±85°
Front Filter Surface Finishing 1.2ohm Sputter
2
Brightness Peak Brightness (1% 320 cd/m or more
window) ( W h e n V I D E O , D a y m o d e , Color te m -
perature 'HIGH' Input Signal A m -
plitude 100 % is set)
2
All White Pattern 5Ocd/m or more
Contrast Contrast ratio 1000 : 1 (typ)

Color Color Reproduction 16.7 million colors or more
Reproduction
Audio Output Audio Output 18W+ 18W(6ohm>,10%Distortion)
Panel Operation Main Power Switch PUSH (LOCK) 1 switch
Power Switch PUSH (NON -LOCK) 1 switch
Input Terminal Video/Audio Input RCA , HDMI DV connector
Output Terminal Audio Line Output Sub Woofer Output 1 system

Speaker Output -
Power Supply Connector 3 Polarity Receptacle
Source Input Voltage Single Phase AC108 -132V, 6 OHz
Guaranteed Temp. (Operating) 5~35°C (41F~95F)

Environment Temperature (Stored) -15~60°C (5F~140F)
Condition Humidity (Operating) 20~80%RH ( N o n - c o n d e n s i n g )
Humidity (Stored) 20~90%RH (Non-condensing)
Atmospheric Pressure 800 to 1114hPa

(Operating) (altitude: 1888m to -757m,
6194feet to -2483feet)
Atmospheric Pressure 300 to 1114hPa (Altitude:
(Storage) 9727m to -757m, 31912feet to -
2483feet)
15
DW2U
Display Specification
웉Continuation웊
Picture Format for Each Input Source Input Auto Aspect Aspect
Aspect, Virtual HD, Black Side Panel, Vertical Position, PIP Mode Signal Aspect Video ID 16:9 16:9 16:9 4:3 4:3 4:3 4:3
Standard 1 Standard 2 Zoom Standard Expanded Zoom 1 Zoom 2
Input 4 YPBPR 1080i/720p 웎 16x9 Yes Yes Yes 웎 Yes 웎 웎
9.1.1 Aspect
480p Auto ON 16x9 Yes Initial 웎 Yes 웎 웎 웎 웎
Yes : Selectable 웎 : Un-selectable
480i Letter 웎 웎 웎 Yes Yes Yes Initial Yes
Input Auto Aspect Aspect
4x3 웎 웎 웎 Yes Yes Initial Yes Yes
Signal Aspect Video ID 16:9 16:9 16:9 4:3 4:3 4:3 4:3
No ID Yes 웎 Yes Yes Yes Yes Yes
Standard 1 Standard 2 Zoom Standard Expanded Zoom 1 Zoom 2
Auto OFF 웎
ANT Video NTSC 웎 4x3 Yes 웎 Yes Yes Yes Yes Yes
No Signal 웎 웎
Analog
Video NTSC Auto ON 16x9 Yes Initial 웎 Yes 웎 웎 웎 웎
ANT YCBCR 480p 웎 16x9 Yes 웎 Yes 웎 Yes 웎 웎
Letter 웎 웎 웎 Yes Yes Yes Initial Yes
Digital 480i 웎 4x3 웎 웎 웎 Yes Yes Yes Yes
YPBPR 1080i/720p 웎 16x9 Yes Yes Yes 웎 Yes 웎 웎
IEEE1394 YCBCR 480p 웎 16x9 Yes 웎 Yes 웎 Yes 웎 웎
Auto OFF 웎
Digital 480i 웎 4x3 웎 웎 웎 Yes Yes Yes Yes
Input 5 HDMI 1080i/720p 웎 16x9 Yes Yes Yes 웎 Yes 웎 웎
웎 웎 웎 1394DV 웎 웎 웎 Yes Yes Yes Yes
480i
No Info Yes 웎 Yes Yes Yes Yes Yes
Auto OFF 웎 Yes 웎 Yes Yes Yes Yes Yes
480i
S-Video Letter 웎 웎 웎 Yes Yes Yes Initial Yes
Auto OFF 웎
No Signal 웎 웎
Auto OFF 웎
Horizontal Expansion 16x9 105% 100% 133% 웎 133% 웎 웎
S-Video Letter 웎 웎 웎 Yes Yes Yes Initial Yes
4x3 105% 100% 133% 75% 100% 100% 133%
Vertical Expansion 105% 100% 133% 110% 110% 133% 176%
Input 3 YPBPR 1080i/720p 웎 16x9 Yes Yes Yes 웎 Yes 웎 웎
Auto OFF 웎
No Signal 웎 웎
Auto OFF 웎
16
DW2U
[Expansion]
<4x3 Format> <16x9 Format>
4:3 Expanded Mode

16:9 16:9
90%
4x3
90%
Standard1 16x9 Standard1

162%
90% 90%
Horizontal
Expansion
16:9 Ratio
16x9 Standard2 (%)

113%

16:9
16:9
75%
4x3
75%
Zoom 16x9 Zoom

Horizontal Position
75% 75%
4x3 16x9
Format Format
4:3
90%
4x3
Standard
100% 100%
4:3 4:3
90%
4x3
90%
Expanded 16x9 Expanded
4:3
Expanded
4:3
75%
4x3 Zoom1
162% 113% 162%
4:3
56%
4x3 Zoom2
75%
17
DW2U
Aspect Key Operation (3) HDMI/YPBPR: 1080i/720p

(1) ANT Analog Channel
Aspect Aspect Aspect

16:9 Key 16:9
16:9 Key 16:9 Key 4:3 Standard1 Standard2
Standard1 Zoom Standard
Aspect Aspect
Aspect Aspect
Key Key
Key Key

4:3 Key 4:3 Key 4:3
4:3 Key 16:9
Zoom2 Expanded Zoom
Zoom1 Expanded
(2) ANT Digital Channel (4) HDMI/YPBPR: 480p/480i, Video/S-Video

(a) Aspect: 16x9 (4-1) Auto Aspect OFF

16:9 Key 16:9
Standard1 Standard2 16:9 Key 16:9 Key 4:3
Standard1 Zoom Standard
(This mode is for
1080i/720p only.)
Aspect Aspect Aspect Aspect

Key Key Key Key
Aspect Aspect
Aspect 4:3 Key 4:3 Key 4:3
4:3 Key 16:9 Zoom2 Zoom1 Expanded
Expanded Zoom
(b) Aspect: 4x3
Aspect (4-2) Auto Aspect ON

4:3 Key 4:3 (a) Video ID/HDMI Info: 16x9
Standard Expanded
Aspect
Key
Video ID: 16x9 16:9 16:9
Aspect Aspect Standard1 Zoom
Power ON Initial
Key Key Aspect
Key
Aspect
4:3 Key 4:3
Zoom2 Zoom1
18
DW2U
Vertical Position Operation

(b) Video ID/HDMI Info: Letter
Input Vertical Position
Aspect 16:9 16:9 4:3 4:3 4:3 4:3
4:3 Key 4:3 Standard1/2 Zoom Standard Expanded Zoom 1 Zoom 2
Standard Expanded ANT Video NTSC 4x3 ¢0 step ¢10 step ¢0 step ¢10 step ¢10 step ¢10 step
Analog Gray out (¢30 lines) Gray out (¢10 lines) (¢30 lines) (¢50 lines)
ANT YPBPR 1080i 16x9 ¢0 step ¢10 step 웎 ¢10 step 웎 웎
Digital 720p Gray out (¢30 lines) (¢10 lines)
Aspect Aspect 480p 4x3 웎 웎 ¢0 step ¢10 step ¢10 step ¢10 step
Key Key Gray out (¢10 lines) (¢30 lines) (¢50 lines)
480i 16x9 ¢0 step ¢10 step 웎 ¢10 step 웎 웎
Aspect Gray out (¢30 lines) (¢10 lines)
4:3 Key 4:3 Video ID: Letter 4x3 웎 웎 ¢0 step ¢10 step ¢10 step ¢10 step
Zoom2 Zoom1 Gray out (¢10 lines) (¢30 lines) (¢50 lines)
Power ON Initial
IEEE1394 YPBPR 1080i 16x9 ¢0 step ¢10 step 웎 ¢10 step 웎 웎
720p Gray out (¢30 lines) (¢10 lines)
480p 4x3 웎 웎 ¢0 step ¢10 step ¢10 step ¢10 step
480i Gray out (¢10 lines) (¢30 lines) (¢50 lines)
Input 1 - 2 HDMI 1080i 16x9 ¢0 step ¢10 step 웎 ¢10 step 웎 웎
(c) Video ID/HDMI Info: 4x3
480p 16x9 ¢0 step ¢10 step ¢0 step ¢10 step ¢10 step ¢10 step
Aspect 480i 4x3 Gray out (¢30 lines) Gray out (¢10 lines) (¢30 lines) (¢50 lines)
4:3 Key 4:3 S-Video NTSC 웎 ¢0 step ¢10 step ¢0 step ¢10 step ¢10 step ¢10 step
Standard Expanded Video Gray out (¢30 lines) Gray out (¢10 lines) (¢30 lines) (¢50 lines)
Input 3 - 4 YPBPR 1080i 16x9 ¢0 step ¢10 step 웎 ¢10 step 웎 웎
Aspect 480i 4x3 Gray out (¢30 lines) Gray out (¢10 lines) (¢30 lines) (¢50 lines)
Aspect Key Video ID: 4x3 Video NTSC 웎 ¢0 step ¢10 step ¢0 step ¢10 step ¢10 step ¢10 step
Key Power ON Initial Gray out (¢30 lines) Gray out (¢10 lines) (¢30 lines) (¢50 lines)
Input5 HDMI 1080i 16x9 ¢0 step ¢10 step 웎 ¢10 step 웎 웎
Aspect 720p Gray out (¢30 lines) (¢10 lines)
4:3 480p 16x9 ¢0 step ¢10 step ¢0 step ¢10 step ¢10 step ¢10 step
Key 4:3
480i 4x3 Gray out (¢30 lines) Gray out (¢10 lines) (¢30 lines) (¢50 lines)
Zoom2 Zoom1
YPBPR 1080i 16x9 ¢0 step ¢10 step 웎 ¢10 step 웎 웎
480i 4x3 Gray out (¢30 lines) Gray out (¢10 lines) (¢30 lines) (¢50 lines)
Video NTSC 웎 ¢0 step ¢10 step ¢0 step ¢10 step ¢10 step ¢10 step
Gray out (¢30 lines) Gray out (¢10 lines) (¢30 lines) (¢50 lines)
(d) No Video ID, No HDMI Info PIP Mode SPLIT/POP/ ¢0 step
PIP/STROBE Gray out
Aspect Aspect
16:9 Key 16:9 Key 4:3
Standard Zoom Standard
9.1.4 Black Side Panel Operation
Black Side Panel OFF Black Side Panel ON

Aspect (Power ON Initial)
Aspect Black Side Panel
Key Key
Menu
4:3 4:3
Aspect Aspect Standard Standard
4:3 Key 4:3 Key 4:3
Zoom2 Zoom1 Expanded
Gray Side Black

Panel Side
19
DW2U
PIP Mode
PIP Sub Digital Component/Composite/S-IN/HDMI POP Mode:

Mode 1080i 720p 480p 480p 480i 480i 1080i 720p 480p 480p 480i 480i
341/256 Lines
341/256 Lines
Main 16x9 16x9 16x9 4x3 16x9 4x3 16x9 16x9 16x9 4x3 16x9 4x3
1024/768 Lines
POP Digital 1080i 16x9 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎 4x3
341/256 Lines
(Air or 720p 16x9 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎
Cable) 480p 16x9 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎 4x3 4x3 4x3
4x3
480p 4x3 웎 웎 웎 웎 웎 웎 Yes Yes Yes Yes Yes Yes
480i 16x9 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎
480i 4x3 웎 웎 웎 웎 웎 웎 Yes Yes Yes Yes Yes Yes 4x3
Component 1080i 16x9 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎
Composite 720p 16x9 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎
S-IN 480p 16x9 Yes*1 Yes*1 Yes*1 Yes*1 Yes*1 Yes*1 웎 웎 웎 웎 웎 웎
HDMI 480p 4x3 Yes Yes Yes Yes Yes Yes 웎 웎 웎 웎 웎 웎 PIP Mode:
480i 16x9 Yes*1 Yes*1 Yes*1 Yes*1 Yes*1 Yes*1 웎 웎 웎 웎 웎 웎
480i 4x3 Yes Yes Yes Yes Yes Yes 웎 웎 웎 웎 웎 웎
PIP Digital 1080i 16x9 웎 웎 웎 웎 웎 웎 Yes Yes Yes*2 웎 Yes*2 웎
16x9 (Air or 720p 16x9 웎 웎 웎 웎 웎 웎 Yes Yes Yes*2 웎 Yes*2 웎 4x3 4x3
1024/768 Lines
Cable) 480p 16x9 웎 웎 웎 웎 웎 웎 Yes Yes Yes*2 웎 Yes*2 웎 16x9 16x9
480p 4x3 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎
480i 16x9 웎 웎 웎 웎 웎 웎 Yes Yes Yes*2 웎 Yes*2 웎
Component 1080i 16x9 Yes Yes Yes 웎 Yes 웎 웎 웎 웎 웎 웎 웎
Composite 720p 16x9 Yes Yes Yes 웎 Yes 웎 웎 웎 웎 웎 웎 웎
S-IN 480p 16x9 Yes*2 Yes*2 Yes*2 웎 Yes*2 웎 웎 웎 웎 웎 웎 웎
HDMI 480p 4x3 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎
480i 16x9 Yes*2 Yes*2 Yes*2 웎 Yes*2 웎 웎 웎 웎 웎 웎 웎
PIP Digital 1080i 16x9 웎 웎 웎 웎 웎 웎 웎 웎 Yes*1 Yes Yes*1 Yes
16x9 16x9
341/256 Lines
4x3 (Air or 720p 16x9 웎 웎 웎 웎 웎 웎 웎 웎 Yes*1 Yes Yes*1 Yes
Cable) 480p 16x9 웎 웎 웎 웎 웎 웎 웎 웎 Yes*1 Yes Yes*1 Yes 4x3 4x3
480i 16x9 웎 웎 웎 웎 웎 웎 웎 웎 Yes*1 Yes Yes*1 Yes
Component 1080i 16x9 웎 웎 웎 Yes 웎 Yes 웎 웎 웎 웎 웎 웎
Composite 720p 16x9 웎 웎 웎 Yes 웎 Yes 웎 웎 웎 웎 웎 웎
S-IN 480p 16x9 웎 웎 웎 Yes*2 웎 Yes*2 웎 웎 웎 웎 웎 웎
HDMI 16x9 16x9
1024/768 Lines
480i 16x9 웎 웎 웎 Yes*2 웎 Yes*2 웎 웎 웎 웎 웎 웎 16x9 16x9
SPLIT Digital 1080i 16x9 웎 웎 웎 웎 웎 웎 Yes Yes Yes Yes Yes Yes
(Air or 720p 16x9 웎 웎 웎 웎 웎 웎 Yes Yes Yes Yes Yes Yes
Cable) 480p 16x9 웎 웎 웎 웎 웎 웎 Yes Yes Yes Yes Yes Yes
480p 4x3 웎 웎 웎 웎 웎 웎 Yes Yes Yes Yes Yes Yes
480i 16x9 웎 웎 웎 웎 웎 웎 Yes Yes Yes Yes Yes Yes
480i 4x3 웎 웎 웎 웎 웎 웎 Yes Yes Yes Yes Yes Yes
Component 1080i 16x9 Yes Yes Yes Yes Yes Yes 웎 웎 웎 웎 웎 웎
Composite 720p 16x9 Yes Yes Yes Yes Yes Yes 16x9 16x9
341/256 Lines
웎 웎 웎 웎 웎 웎
S-IN 480p 16x9 Yes Yes Yes Yes Yes Yes 웎 웎 웎 웎 웎 웎
HDMI 480p 4x3 Yes Yes Yes Yes Yes Yes 웎 웎 웎 웎 웎 웎 16x9 16x9
STROBE Digital 1080i 16x9 Yes 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎
(4pix) (Air or 720p 16x9 웎 Yes 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎
Cable) 480p 16x9 웎 웎 Yes 웎 웎 웎 웎 웎 웎 웎 웎 웎
480p 4x3 웎 웎 웎 Yes 웎 웎 웎 웎 웎 웎 웎 웎 SPLIT Mode: STROBE Mode:
480i 16x9 웎 웎 웎 웎 Yes 웎 웎 웎 웎 웎 웎 웎
768/576 Lines (93%)

480i 4x3 웎 웎 웎 웎 웎 Yes 웎 웎 웎 웎 웎 웎
4x3
Component 1080i 16x9 웎 웎 웎 웎 웎 웎 Yes 웎 웎 웎 웎 웎
341/256 Lines
Composite 720p 16x9 웎 웎 웎 웎 웎 웎 웎 Yes 웎 웎 웎 웎
S-IN 4x3 4x3 4x3 4x3
480p 16x9 웎 웎 웎 웎 웎 웎 웎 웎 Yes 웎 웎 웎
HDMI 480p 4x3 웎 웎 웎 웎 웎 웎 웎 웎 웎 Yes 웎 웎
480i 16x9 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎 Yes 웎 4x3
480i 4x3 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎 웎 Yes
Yes*1: Auto Aspect OFF
Yes*2: Auto Aspect ON
20
DW2U
(1) PIP Key Operation (2) Freeze Operation

Normal Viewing
Main
Frozen
Freeze
Key
PIP Exit
Freeze
Key Key
Key Main Sub
Moving Frozen
Freeze
Key
Freeze
POP Key
STROBE
SPLIT
PIP PIP
Key Key (3) SWAP Operation
PIP
4x3
Main Sub
Audio Audio
PIP Key
࿵
࿿
16x9 A B A B
Main Sub
Audio Key Audio
࿵
࿿
A A
Exit
B B
Key Main Sub
Audio Audio
Key
࿵
࿿
A B A B
PIP OFF PIP OFF
(Note)
If PIP Key is pushed from a Normal screen, PIP of Last Mode will be displayed.
A shipment setup of PIP Mode is SPLIT Mode.
A B
POP/PIP Mode cannot display 720p/480p signals. Therefore, it displays by SPLIT Mode.
ሩWhen Last mode is POP/PIP Mode and a Main signal is 1080i, PIP Mode is set to PIP.
ሩWhen Last mode is POP/PIP Mode and a Main signal is 480i/NTSC, PIP Mode is set to PIP.
ሩSURF Mode is not displayed at a V-Chip setup. SPLIT Mode is displayed at this time. (Note)
When EXIT Key is pushed, PIP turns off. When right and left Key are pushed, the sound of Main and Sub interchanges.
When PIP is turns off, PIP Mode of a display turns into Last Mode. A Channel/Input change can do the screen out of which the sound has come.
When PIP OFF [EXIT Key], the screen where sound is sounding turns into a normal screen.
21
DW2U
(4) Monitor Out

(4-1) Set the Monitor out: Monitor out
(4-2) Set the Monitor out: TV out
Main Sub
Audio Audio Main Sub
Key
࿵
࿿
Audio Key Audio
A A
࿵
࿿
B B
A B A B
Main Sub
Key Audio
Audio Main Sub
࿵
࿿
Audio Key Audio
࿵
࿿
A A
B B A A
B B
Main Sub
Audio Audio Main Sub
Key
Audio Audio
࿵
࿿
A B A B Key
࿵
࿿
A B A B
Monitor Out Monitor Out

Sub
Main
Audio
Audio
Monitor Out Monitor Out
A B D
C
(Note) (Note)
When right and left Key are pushed, the sound of Main and Sub interchanges. When right and left Key are pushed, the sound of Main and Sub interchanges.
The picture and sound of the selected picture are outputted from Monitor out. The picture and sound of ANT is outputted from Monitor out.
When the selected picture is Component or HDMI signal and audio out is monitor, When ANT is analog channel, S-Video of monitor out is no picture.
monitor out is no picture and no audio. When Macrovision signal is included in the ANT Digital channel, monitor out is no picture and no audio.
When the selected picture is Component or HDMI signal and audio out is HiFi out,
monitor out is no picture but audio is output. Main/Sub Audio Select
When the selected picture is Composite Video signal, S-Video of monitor out is no picture. Input Mode Monitor Out: TV out
When Macrovision signal is included in the ANT Digital channel, monitor out is no picture and no audio. S-Video Video L/R HiFi
ANT Digital No Macrovision S-Video YES YES YES YES
Main/Sub Audio Select (AIR or Channel ANT ANT ANT ANT
Input Mode Monitor Out CABLE) Macrovision S-Video 웎 웎 웎 YES
S-Video Video L/R HiFi ANT
Analog Channel Video 웎 YES YES YES
ANT Digital No Macrovision S-Video YES YES YES YES ANT ANT ANT
(AIR or Channel Macrovision S-Video 웎 웎 웎 YES Input_1 HDMI_1 YPBPR YES YES YES YES
CABLE) Analog Channel Video 웎 YES YES YES S-Video_1 ANT ANT ANT ANT
Input1 HDMI_1 웎 웎 웎 YES Video_1 Digital only
S-Video_1 YES YES YES YES Input_2 HDMI_2 YPBPR
Video_1 웎 YES YES YES S-Video_2
Input2 HDMI_2 웎 웎 웎 YES Video_2
S-Video_2 YES YES YES YES Input_3 YPBPR_3
Video_2 웎 YES YES YES Video_3
Input3 YPBPR_3 웎 웎 웎 YES Input_4 YPBPR_4
Video_3 웎 YES YES YES
Video_4
Input4 YPBPR_4 웎 웎 웎 YES
Input_5 HDMI_5 YPBPR
Video_4 웎 YES YES YES Side YPBPR_5
Input5 HDMI_5 웎 웎 웎 YES Video_5
Side YPBPR_5 웎 웎 웎 YES
Video_5 웎 YES YES YES
22
DW2U
(4-3) At the time of reservation videotape recording

Main Sub
Audio Audio (4) PIP Position Operation
Key
࿵
࿿
A B A B
Main Sub
Audio Key Audio
࿵
࿿
A Key Key
A
B B
Main Sub
Audio Audio
Key Key
Key
࿵
࿿
A B A B
Key Key
Monitor Out
C
(Note)
At the time of reservation videotape recording, the picture and sound of ANT is outputted from Monitor out.
When Macrovision signal is included in the ANT Digital channel, monitor out is no picture and no audio. Key
Main Audio Select

Input Mode Monitor Out: TV out
S-Video Video L/R HiFi
ANT Digital No Macrovision S-Video YES YES YES YES
(AIR or Channel ANT ANT ANT ANT Key Key
CABLE) Macrovision S-Video 웎 웎 웎 YES
ANT
Analog Channel Video 웎 YES YES YES
ANT ANT ANT
Input_1 HDMI_1 YPBPR YES YES YES YES
S-Video_1 ANT ANT ANT ANT
Video_1 Digital only Key
S-Video_2
Video_2 (Note)
Input_3 YPBPR_3 The Sub screen position of POP Mode moves up and down by the upper and lower sides Key.
Video_3 A Sub screen position of PIP Mode moves clockwise by the upper and lower sides Key.
Input_4 YPBPR_4
Video_4
Side YPBPR_5
Video_5
When Macrovision signal is included in the ANT Digital channel, monitor out is no picture and no audio.
23
How To Set Up Your New Hitachi Plasma Television
To take measures to prevent the Plasma Display from tipping over and prevent possible injury it
is important to mount the unit in a stable and flat surface.
Securing to a table-top ANTENNA

1. Using wood screws (two) fasten the set to the Unless your Plasma Television is connected to a cable
clamping screw holes on the rear of the Plasma TV system or to a centralized antenna system, a good
Display stand as shown below. outdoor color TV antenna is recommended for best
2. Using commercially available wood screws, secure performance. However, if you are located in an
the set firmly in position. exceptionally good signal area that is free from
Wire interference and multiple image ghosts,
an indoor antenna may be sufficient.
LOCATION
Wood screw Select an area where sunlight or bright indoor
two places illumination will not fall directly on the picture screen.
Securing to a Wall Also, be sure that the location selected allows a free
1. Keep the Plasma television 4 inches away from the flow of air to and from the perforated back cover of the
wall except when mounted using the wall mount set. In order to prevent an internal temperature
bracket. increase, maintain a space of 10 cm (4 inches) from the
2. Secure the television to the wall as shown in fig. (a) sides/back of the monitor, and 30 cm (12 inches) from
or (b). the top of the television to the wall. To avoid cabinet
warping, cabinet color changes, and increased chance
10cm (4 inches) 30cm (11.8 inches)
or more or more of set failure, do not place the TV where temperatures
can become excessively hot, for example, in direct
sunlight or near a heating appliance, etc.
30 cm (12 inches)
A B
42" 4 in. 12 in.
10 cm 30 cm
55" 4 in. 16 in. 10 cm (4 inches) 10 cm (4 inches)
10 cm 39 cm
(a) Power Swivel (b) Power Swivel

NOT USED USED
NOTES: 1. Do not block the ventilation holes of

the Plasma Display monitor. Blocking CONNECT POWER SWIVEL CABLE
the ventilation holes might cause fire Connect one end of cable (Arrow mark facing left) to
or defect. the swivel slot of the Plasma Rear Panel. Connect the
2. In case of an abnormal symptom, other end (Arrow mark facing front)to the swivel slot of
unplug the AC cord.
the Table Top Stand.
3. If you purchased the wall mount
bracket option, please ask for
professional installer. Do not install
by yourself.
4. If the Power Swivel feature will not be
used, the Plasma television should be
secured to the wall as shown in
fig. (a).
5. If the Power Swivel feature will be
used, the Plasma television should be
TURNING RADIUS
secured to the wall as shown in
fig. (b). The wires need to be long The maximum turning radius is 30˚ (left and right). Do
enough to allow the television to turn not place any objects on the path of the monitor when
30˚ to the left and right. using the power swivel feature.
Caution when moving the main unit

11.8in
As this product is heavy, whenever it is moved, two (30cm) C
people are required to transport it safely. Whenever the

unit is moved it should be lifted forward using the top
11.8in D
and base on both sides of the Display Monitor for (30cm)
stability. When moving the Display Monitor, lift the
handles and the bottom frame as shown below. Do not C D
42" 12 in. 12 in.
grab the speakers or the back cover when lifting. 30 cm 30 cm
55" 15.26 in. 16.46 in.
38.77 cm 41.8 cm
24
TABLE OF CONTENTS
HOW TO SET UP YOUR NEW HITACHI PLASMA TELEVISION
VIEWING
The best picture is seen by sitting directly in front of

the TV and about 10 to 18 feet from the screen.
During daylight hours, reflections from outside light

may appear on the screen. If so, drapes or screens
BEST
can be used to reduce the reflection or the TV can
VERTICAL VIEWING
be located in a different section of the room. 20 ANGLE
If the TV’s audio output will be connected to a Hi-Fi 3’

system’s external speakers, the best audio
0’ 5’ 10’ 15’ 20’
performance will be obtained by placing the
speakers equidistant from each side of the receiver
cabinet and as close as possible to the height of
the picture screen center. For best stereo
separation, place the external speakers at least
four feet from the side of the TV, place the surround R S
speakers to the side or behind the viewing area.
Differences in room sizes and acoustical
4" Minimum 80 BEST
environments will require some experimentation
with speaker placement for best performance. HORIZONTAL
5' 10' 15' 20'

VIEWING ANGLE
80
4" Minimum
ANTENNA CONNECTIONS TO REAR JACK

L S
PANEL
VHF (75-Ohm) antenna/CATV (Cable TV)

When using a 75-Ohm coaxial cable system, connect CATV coaxial cable to the AIR/CABLE (75-Ohm) terminal. Or if you
have an antenna, connect the coaxial cable to the same AIR/CABLE terminal.
AIR / CABLE
To CATV cable
VHF (300-Ohm) antenna/UHF antenna
When using a 300-Ohm twin lead from an outdoor
antenna, connect the VHF or UHF antenna leads to or
To outdoor antenna
screws of the VHF or UHF adapter. Plug the adapter
into the antenna terminal on the TV.
AIR / CABLE
When both VHF and UHF antennas are

To outdoor VHF
connected or UHF antenna
Attach an optional antenna cable mixer to the TV
antenna terminal, and connect the cables to the
antenna mixer. Consult your dealer or service store for To UHF AIR / CABLE
To outdoor antenna
the antenna mixer. antenna or CATV system
Antenna Mixer
NOTE: Connecting a 300-Ohm twin lead connector may cause interference. Using a 75-Ohm coaxial
cable is recommended.
25
Hook-up Cables and Connectors
Most video/audio connections between components can be made with shielded video and audio cables that have
phono connectors. For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be
purchased from most stores that sell audio/video products. Below are illustrations and names of common
connectors. Before purchasing any cables, be sure of the output and input connector types required by the
various components and the length of each cable.
300-Ohm Twin Lead Connector

This outdoor antenna cable must be connected to an
antenna adapter (300-Ohm to 75-Ohm).
Phono Connector
Used on all standard video and audio cables which
connect to inputs and outputs located on the
television’s rear jack panel and front control panel.
“F” Type 75-Ohm Coaxial Antenna Connector

For connecting RF signals (antenna or cable TV) to the
antenna jack on the television.
S-Video (Super Video) Connector

This connector is used on camcorders, VCRs and laser-
disc players with an S-Video feature in place of the
standard video cable to produce a high quality picture.
Optical Cable
This cable is used to connect to an audio amplifier with
an Optical Audio In jack. Use this cable for the best
sound quality.
HDMI Cable
This cable is used to connect your external devices
such as Set-Top-Boxes or DVD players equipped with
an HDMI output connection to the TV’s HDMI input.
Stereo Cable (3.8mm plug to 3.5mm plug)

Used on all standard video and audio cable which
connect to inputs and outputs located on the rear jack AUDIO OUT
2
3.8mm
panel and front control panel. STEREO RCA TYPE
PLUGS
MINI-PLUG
USB Cable (HDT & HDX only)

This cable is used to connect your digital camera to the
Photo Input in the side of the Plasma television.
IR Mouse Cable (Provided) (HDT & HDX only)

Connect the IR Mouse to the IR output of your Plasma
Television when A/V Network is used. You must place
the IR mouse in front of the corresponding IR window
of your cable box and VCR. This connection allows
your TV to control your cable box and VCR.
Power Swivel Cable (Provided) (HDT & HDX only)

This cable is used to connect the swivel stand to the
rear panel of the Plasma Television.
26
QUICK REFERENCE REMOTE CONTROL
42HDT79 and 42HDX99 Models Only
POWER BUTTON
(TV, DVD, CBL, STB, PVR/VCR, AMP/CD)
Turns the selected device on and off.
MODE INDICATOR
Turns on or blinks to show remote control
mode when the SOURCE ACCESS buttons DVD/VCR CONTROL BUTTONS
are pressed. (DVD, PVR/VCR, AMP/CD)
Controls the functions of your VCR, DVD
SOURCE ACCESS BUTTONS and audio devices.
Changes the mode of the Universal Remote PAUSE BUTTON
Control to control the device selected. (TV,PVR/VCR, DVD, AMP/CD)
Press to show and change the Freeze mode of the TV.
ASPECT BUTTON Also used to pause other devices when the remote is in
(TV) DVD, PVR/VCR, or AMP/CD mode.
Changes the aspect ratio of the TV.
PIP CONTROL BUTTONS
DAY/NIGHT (TV)
(TV) Press to show and change the Picture-in-Picture mode.
Toggles picture mode settings between
DAY and NIGHT mode.
MENU BUTTON GUIDE BUTTON

(TV, DVD, CBL, STB, PVR/VCR) (TV, STB, CBL, PVR)
Accesses the OSD menu system. TM
Accesses the TV Guide On Screen system (see page 54)
of the TV or the program guide of other devices.
CURSOR PAD/SELECT BUTTON
(TV, DVD, CBL, STB, PVR/VCR) EXIT BUTTON
The Cursor Pad is used as a cursor to navigate (TV, CBL, STB, PVR/VCR)
through the OSD and INPUT menu systems. Exits out of the OSD, INPUTS or AV NET menu
The Select button is used to Select/Activate systems if their menu is displayed.
highlighted menu items.
CURSOR UP & DOWN /CH + & CH - BUTTON LAST CHANNEL BUTTON
(TV, CBL, STB, VCR) (TV, CBL, STB, PVR)
The CH+ or CH- is used to change channels up or down. Switches between the current and last channel viewed.
The Cursor UP or DOWN to navigate through the OSD
and INPUT menu systems. INPUTS BUTTON
INFO BUTTON (TV, AMP)
(TV, STB, CBL, PVR) Accesses the INPUTS menu system.
Displays various information on the screen,
such as channel information.
VOLUME WHEEL CHANNEL WHEEL

(TV, AMP/CD) (TV, CBL, STB, PVR/VCR, AMP/CD)
Scroll up and down to adjust the audio level of your Scroll up or down to change channel. Push down on
TV. Push down on the wheel to mute. the wheel to access (FAV) Favorite Channel mode.
(Favorite channel is only available for TV mode.)
NUMERIC BUTTONS
Used to manually enter the TV channel, and used
for numeric entry when navigating through the OSD,
INPUTS, and AV NET menu systems.
(-) BUTTON LIGHT BUTTON

(TV,STB) (TV, CBL, STB, PVR)
The (-) button is used when the remote is in Press to use the back light feature. Can
Set-Top-Box (STB) mode or when the TV uses also be used to change backlight mode.
a digital input.
In addition to controlling all of the functions on your HITACHI Plasma TV, the remote control is designed to operate different types of
devices, such as, DVD Players, Cable Boxes (CBL), set-top-boxes, satellite receivers, PVRs/VCRs and audio devices. The remote
control must be programmed to control the chosen device. Refer to Instruction Book for detailed programming instructions.
LEGEND NOTES: 1. VCR precode is included in the PVR mode.

TV - Television 2. CD precode is included in the AMP mode.
DVD - Digital Video Disc Player 3. Pressing any buttons will illuminate the backlight for 4 seconds while in
CBL - Cable Box Automatic mode (Default).
STB - Set-Top-Box/Satellite Receiver
PVR - Personal Video Recorder
VCR - Video Cassette Recorder/Player
AMP/CD - Amplifier/Compact Disc
Player, Audio Devices
27
QUICK REFERENCE REMOTE CONTROL
In addition to controlling all of the functions on your HITACHI Plasma TV, the new remote control is
designed to operate different types of devices, such as, DVD Players, CBL (Cable Boxes), set-top-boxes, satellite
receivers, and VCRs. The remote control must be programmed to control the chosen device. Please see pages of
the OWNERS GUIDE for a complete description of all features and programming of the Remote Control.
42HDS69 Model Only
POWER BUTTON SOURCE ACCESS BUTTONS
(TV, CBL, VCR, DVD, SAT) (TV, DVD, VCR, CBL, SAT)
Turns the selected device on Changes the mode of the
and off. Universal Remote Control to
control the device selected.
INPUTS BUTTON (TV)
Accesses the INPUTS menu DAY/NIGHT BUTTON (TV)
system. Select picture mode settings
between DAY and NIGHT mode.
ASPECT BUTTON (TV)
Changes the aspect ratio while PIP BUTTON (TV)
watching TV. Press to show and change the
Picture-in-Picture mode.
MENU BUTTON
(CBL, DVD, SAT, TV) EXIT BUTTON
Accesses the OSD menu (TV, CBL, SAT)
system. Exits out of the OSD or INPUTS
menu systems if their menu is
CURSOR/SELECT BUTTONS displayed.
(TV, DVD, CBL, SAT)
The CURSOR buttons are used FAVORITE CHANNEL
to navigate the cursor through (FAV CH) button (TV)
the OSD and INPUTS menu Press to enter/access Favorite
systems, and the SELECT Channel (FAV) mode.
button is used to
Select/Activate the highlighted GUIDE BUTTON
menu item. (SAT, CBL)
Accesses the program guide of
VOLUME BUTTONS (TV) other devices.
Adjusts the audio level of your
TV.
INFO BUTTON
MUTE BUTTON (TV) (TV, CBL, SAT)
Reduces the audio level to 50% Displays various information on
if pressed once, and to the screen.
complete mute if pressed twice.
Press it a third time to restore CHANNEL BUTTONS
audio level. (TV, CBL, SAT, VCR)
Changes the channel.
NUMERIC BUTTONS
(TV, DVD, CBL, SAT, VCR) LAST CHANNEL (LC) BUTTON
Used to manually enter the TV (TV, CBL, SAT)
channel, and used for numeric Switches between the current
entry when navigating through and last channel viewed.
the OSD menu system.
DVD/VCR CONTROL
(-) BUTTON (TV, SAT) BUTTONS (DVD, VCR)
The (-) button is used when the Controls the precode functions
remote is in Set-Top-Box (STB) of your VCR and DVD.
mode or when the TV uses a
digital input. PAUSE BUTTON
(TV, VCR, DVD)
RECORD BUTTON (VCR) Press to show and change the
Press twice (2 times) to record Freeze mode of the TV or pause
programs. other devices.
LEGEND
TV — Television VCR — Video Cassette Recorder/Player SAT— Satellite Receiver
CBL — Cable Box DVD — Digital Video Disc Player
NOTES: 1. The TV’s remote control sensor is located on the right bottom portion of the TV screen. To
control TV functions, please point the remote control directly at the remote control sensor for
best results.
28
Front/Rear/Side Panel Controls
FRONT VIEW
42HDS69 42HDT79 & 42HDX99

Model Only Models Only
햺 햹
햸
햴 햽
REAR/SIDE VIEW
햶
햷
PB
햵 햻
PR
햳
햸 Firmly bind the cables.

Thread the square Hook the band
hole with the band. to the claw.
햲 SIDE POWER button

Press this button to turn the Plasma Television
ON/OFF. It can also be turned ON/OFF by remote NOTE: The Rear View of the 55” model is slightly
control. The “MAIN POWER” button must be at different from the 42” models. One of the
stand-by mode. differences are the handles that are only
present on the 42” models.
햳 MENU/SELECT button
This button allows you to enter the MENU, making 햸 POWER button
it possible to set TV features to your preference Television MAIN POWER button
without using the remote. This button also serves This power button is for the complete system, and
as the SELECT button when in MENU mode. must be turned ON/OFF manually. It is
recommended to leave the “MAIN POWER” to ON
햴 SIDE HDMI INPUT (5) condition (lights red) for stand-by mode.
Use the side HDMI input for extrenal devices such
as Set-Top-Boxes or DVD players equipped with an The Main Power
HDMI output connection (see page 16 for reference). button is located on
the broadside
햵 INPUT/EXIT button bottom, under the
Press this button to access the INPUT menu. label “MAIN
Press again to exit the MENU mode. POWER”.
햶 CHANNEL selector
Press these buttons until the desired channel NOTE: When the “MAIN POWER” button is set to
appears in the top right corner of the TV screen. OFF or the TV is unplugged, the clock will
stop and may eventually reset itself.
These buttons also serve as the cursor down ()
and up () buttons when in MENU mode.
햷 VOLUME level
Press these buttons to adjust the sound level. The
volume level will be displayed on the TV screen.
These buttons also serve as the cursor left () and 29
right () buttons when in MENU mode.
Front/Rear/Side Panel Controls
햹 POWER light indicator
To turn the TV ON, press the main power
switch located on the lower right side of the
TV. A red stand-by indicator lamp located on
the lower right corner of the front bezel will
illuminate. The Plasma TV is now ready for
remote ON/OFF operation. Lamp 1 Lamp 2
Indicating Lamp Power Status Operating

Lamp 1 Lamp 2
Off Off OFF. When the main power switch is set to Off.
Lights Off OFF. When the main power switch on the TV

Red (Stand-by) is ON.
Off Blinking OFF.
TV MAIN POWER is ON ; but no picture is shown.
Blue (Turning ON )
Off Lights On TV MAIN POWER is ON ; picture is shown.
Blue
Lights Off TV MAIN POWER is ON with no signal input
Orange Off (Power Saving) except antenna (no sync. signal).
햺 REMOTE CONTROL sensor 햽 PHOTO INPUT

Point your remote at this area when selecting Insert USB cable from your Digital Camera, USB
channels, adjusting volume, etc. memory or memory card USB drive to view your
(Only HDT & HDX models)
digital still pictures (see Owners Guide).
햺 LEARNING AV NET sensor
Point your equipment’s remote control at this area
while using the AV NET Learning Wizard.
햻 SIDE INPUT JACKS (for IN PUT: 5)

INPUT 5 provide Y-PBPR jacks for
connecting equipment with this capability, such as
a DVD player or Set Top Box. You may use
composite video signal for both inputs.
NOTE: 1. Your component outputs may be labeled

Y, B-Y, and R-Y. In this case, connect the
components B-Y output to the TV’s PB
input and the components R-Y output to
the TV’s PR input.
2. Your component outputs may be labeled
Y-CBCR. In this case, connect the component
CB output to the TV’s PB input and the
component CR output to the TV’s PR input.
3. It may be necessary to adjust TINT to
obtain optimum picture quality when using
the Y-PBPR inputs (see page 37).
4. INPUT 3, INPUT 4 and INPUT 5 (Y/VIDEO) can
be used for composite video and component
video input.
NOTES: 1. Your HITACHI Plasma TV will appear to be turned OFF (lights orange) if there is no video input
when INPUT : 1, 2, 3, 4 and 5. Check the Power Light to make sure the TV is turned off or
in Stand-by mode (lights red) when not in use.
2. Remote Control can not turn ON/OFF the “MAIN POWER” of the TV.
30
REAR PANEL CONNECTIONS
햲 햸
햲 Antenna Input
The remote control allows you to switch between
two separate 75-Ohm RF antenna inputs, CABLE
and AIR. CABLE input can be displayed as a main
햿
picture or sub-picture. AIR can only be displayed
as a main picture (AIR cannot be displayed as a 햺
sub-picture). 햹
햶 햽
햳 Audio/Video Inputs 1, 2, 3 and 4 햻
By using the INPUTS button, the CURSOR PAD (
and ), and the SELECT button or CURSOR PAD 햷
of the remote control, you can select each video
source. Use the audio and video inputs to connect
external devices, such as VCRs, camcorders,
laserdisc players, DVD players etc. (if you have
mono sound, insert the audio cable into the left 햴 햳 햾햵
audio jack). trademarks of HDMI Licensing LLC.
햴 MONITOR OUT & HI-FI AUDIO OUT NOTE: 1. The HDMI input is not intended for use
These jacks provide fixed and variable audio and with personal computers.
video signals (CABLE/AIR, INPUT 1, 2 and 5) 2. Only DTV formats such as 1080I, 720P, 480I
which are used for recording. Use the S-VIDEO and 480P are available for HDMI input.
Output for high quality video output. Component
signal to Input 1 and 2, and HDMI inputs will not 햸 Component: Y-PBPR Inputs
have monitor output. INPUTS 3 and 4 provide Y-PBPR jacks for
connecting equipment with this capability, such as
햵 Optical Out (Digital Audio) a DVD player or Set Top Box. You may use
This jack provides Digital Audio Output for your composite video signal for both inputs.
audio device that is Dolby® Digital and PCM
compatible, such as an audio amplifier. NOTE: 1. Do not connect composite VIDEO and
S-VIDEO to INPUT 1 or 2 at the same
NOTE: *Manufactured under license from Dolby time. S-VIDEO has priority over VIDEO input.
Laboratories. “Dolby” and the double-D 2. Your component outputs may be labeled
symbol are trademarks of Dolby Y, B-Y, and R-Y. In this case, connect the
Laboratories. components B-Y output to the TV’s PB
input and the components R-Y output to
햶 S-VIDEO Inputs 1 and 2 the TV’s PR input.
Inputs 1 and 2 provide S-VIDEO (Super Video) 3. Your component outputs may be labeled
jacks for connecting equipment with S-VIDEO Y-CBCR. In this case, connect the component
output capability. CB output to the TV’s PB input and the
component CR output to the TV’s PR input.
NOTE: 1. You may use VIDEO or S-VIDEO inputs to 4. It may be necessary to adjust TINT to
connect to INPUT 1 and 2, but only one of obtain optimum picture quality when using
these inputs may be used at a time. the Y-PBPR inputs (see page Owners Guide).
2. S-VIDEO output may be used for 5. To ensure no copyright infringement, the
recording, only when the input is of S- MONITOR OUT output will be abnormal,
VIDEO type. when using the Y-PBPR jacks and HDMI
Input.
햷 HDMI1&2 (High Definition Multimedia 6. INPUT 3 , 4 and 5 (Y/VIDEO) can be
Interface) (INPUT 1&2) used for composite video and component
ABOUT HDMI – HDMI is the video input.
next-generation all digital interface for consumer
electronics. HDMI enables the secure distribution 햹 IR Blaster
of uncompressed high-definition video and multi- This jack provides IR output to your external components
channel audio in a single cable. Because digital (VCR, Cable box, DVD player, etc.). With this connection,
television (DTV) signals remain in digital format, your external components can automatically be controlled
HDMI assures that pristine high-definition images by the A/V network feature. This connection will allow you
retain the highest video quality from the source all to control the external components with your Plasma
the way to your television screen. Television’s remote control in TV mode.
Use the HDMI input for your external devices such
as Set-Top-Boxes or DVD players equipped with an 햺 For Service Use Only
HDMI output connection. Do not connect anything to this terminal.
Specifically for Service use only.
HDMI, the HDMI logo and High-Definition 31
Multimedia Interface are trademarks or registered
FRONT/REAR/SIDE PANEL CONNECTIONS
햻 IEEE1394 (DV INPUT) If the CableCARD is properly installed or removed, the
These jacks provide a digital interface for your TV will display the following respective screens.
external digital devices, such as a Digital VCR (D-
VHS), Set-Top-Box or Digital Camcorder by means
of a single cable (see page 19). When using
IEEE1394 connections, you enable video and audio
digital data exchange between a compatible
device. This connection also enables you to CableCARD is installed
control basic equipment functions (such as VCR
play, rewind, fast forward, stop, etc.) from your TV
On-Screen Display.(Only HDT & HDX models)
햽 Upgrade Card
This card slot is for future software upgrades.
Hitachi will notify you if a software upgrade is OR
required for your TV. In order to receive written
notification, please complete and return your
warranty card.
CableCARD is not installed
햾 To Power Swivel Connector
Connects to the Power Swivel Table Top Stand.
햿 CableCARD Slot
This slot is for the CableCARD that will be provided
After the CableCARD is installed, wait until the second
by your local cable operator to gain access to
screen below appears. The third screen below will
chosen cable channels. The CableCARD will allow
appear if a channel is not authorized for viewing. Press
you to tune digital and high definition cable
the EXIT button to exit the second screen.
channels. Please call your local cable operator if
this service is available before requesting a
CableCARD (also known as Point of Deployment
(POD) module).
1. Connect a coaxial cable to cable terminal of

Acquiring Data.
the Rear Panel Jacks. Please wait.
2. Insert the CableCARD into the slot (Top of card
should be facing towards you as shown
below).
Digital Cable
In order to start cable service

for this device, please contact
your cable provider
CableCARD(tm): 123-456-789-1
Host: 123-456-789-1
Data: 123-456-789-1
INSERT Unit Address: 123-456-789-1
Press EXIT to return
OR
Not an Authorized Channel
NOTE: 1. A digital cable subscription is required. Please take note of all information on the screen (you
2. Do not insert a PCMCIA card into the will provide this information to your cable operator).
CableCARD slot. Call your cable operator and give them the information
from the card to start your cable service.
32
Connecting External Video Sources
The LEFT SIDE panel jacks are provided as a convenience to allow you to easily connect a camcorder , DVD, Video
Game or VCR as shown in the following examples:
Left Side Panel Left Side Panel

INPUT 5
INPUT 5
R L/MONO
R L/MONO AUDIO PR PB
AUDIO PR PB Y / VIDEO
Y / VIDEO
Note : Special device cables will be

according to the own device
specifications.
OUTPUT
OUTPUT R L V
R L PR /C R PB /C B Y
COMPONENT
Video Game OUTPUT CAPABILITY
DVD , Set Top Box,
Video Game Console.
Video Camera
NOTE: 1. Completely insert connection cord plugs when connecting to left side panel jacks. If you do not, the
played back picture may be abnormal.
33
Connecting External Video Sources
The RIGHT SIDE panel jacks are provided as a convenience to allow you to easily connect HDMI or DVI signals
from a DVD, Set Top Box , Video Game as shown in the following examples (When connecting DVI signal it will
need to connect the audio output into the Left Side Input jacks) :
A) Connecting HDMI signal. B) Connecting DVI signal.

Right Side Panel Right Side Panel Left Side Panel
INPUT 5
R L/MONO
AUDIO PR PB
Y / VIDEO
DVI to HDMI
Cable
Note : Special device cables will be

DIGITAL OUTPUT OUTPUT
according to the own device R L
specifications.
Back of
HDMI DIGITAL
OUTPUT CAPABILITY HDTV Set-Top-Box or
DVD , Set Top Box, DVD Player
Video Game Console.
DVI DIGITAL
OUTPUT CAPABILITY
DVD , Set Top Box,
Video Game Console.
NOTE: 1. Completely insert connection cord plugs when connecting to side panel jacks. If you do not, the
played back picture may be abnormal.
The exact arrangement you use to connect the VCR, camcorder, laserdisc player, DVD player, or HDTV Set
Top Box to your Plasma TV is dependent on the model and features of each component. Check the
owner’s manual of each component for the location of video and audio inputs and outputs.
The following connection diagrams are offered as suggestions. However, you may need to modify them to
accommodate your particular assortment of components and features. For best performance, video and
audio cables should be made from coaxial shielded wire.
Before Operating External Video Source

Connect an external source to one of the INPUT terminals, then press the INPUTS button to show the
INPUTS menu. Use the CURSOR PAD ( and ) to select the Antenna or Input of your choice. Then press
the SELECT button or the CURSOR PAD to confirm your choice (see page 26).
INPUTS
Input 4
Input 5
Air / Cable
Input 1
Input 2
Move SEL Sel.
34
CONNECTING EXTERNAL VIDEO SOURCES
Cable TV coaxial cable
2-Way signal splitter
Outside
Antenna VCR #1 DIGITAL
ANT
OUTPUT OUTPUT CAPABILITY
IN S-VIDEO V L R
DIGITAL OUTPUT
AUDIO OUT
Optional DVI
to
HDMI
DV or 1394 OUTPUT
DVHS
DV or 1394
OUTPUT CAPABILITY
HDMI
to
HDMI
Optional
OUTPUT
Y PB/CB PR/CR L R HDMI OUTPUT
S-VIDEO V L R S-VIDEO V L R Y PB PR L R
INPUT OUTPUT OUTPUT
VCR #2 HDMI DIGITAL

DVD Player Laserdisc player, VCR, HDTV Set-Top Box
camcorder, etc. OUTPUT CAPABILITY
(PROVIDED)
(PROVIDED)
CONNECT T
IR BLASTER CONNECT TO
IR BLASTER
NOTE: Cables are optional, except when specified.
35
TIPS ON REAR PANEL CONNECTIONS
• S-VIDEO, Y-PB PR, or HDMI connections are provided for high performance laserdisc players, VCRs etc. that
have this feature. Use these connections in place of the standard video connection if your device has this
feature.
• If your device has only one audio output (mono sound), connect it to the left audio jack on (L/(MONO)) the
Rear Panel.
• Refer to the operating guide of your other electronic equipment for additional information on connecting
your hook-up cables.
• A single VCR can be used for VCR #1 and VCR #2, but note that a VCR cannot record its own video or line
output (INPUT: 1 in the example on page 14). Refer to your VCR operating guide for more information on
line input-output connections.
• Connect only 1 component (VCR, DVD player, camcorder, etc.) to each input jack.
• COMPONENT: Y-PBPR (Input 3, 4 & 5) connections are provided for high performance components, such as
DVD players and set-top-boxes. Use these connections in place of the standard video connection if your
device has this feature.
• Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y
output to the TV’s PB input and the components R-Y output to the TV’s PR input.
• Your component outputs may be labeled Y-CBCR. In this case, connect the components CB output to the
TV’s PB input and the components CR output to the TV’s PR input.
• It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-PBPR inputs. (See
page 37)
• To ensure no copyright infringement, the MONITOR OUT output will be abnormal, when using the Y-PBPR, and
HDMI input jacks.
• Input 1 , 2 or 5 can accept HDMI signal.

• S-VIDEO monitor output may be used for recording only when the input is of S-VIDEO type.
• When using a HDMI input from a Set-Top-Box, it is recommended to use a 1080i or 720p input signal.
INSTALLATION RECOMMENDATION:
1. Video signals fed through a VCR may be affected by copyright protection systems and the picture will be
distorted on the television.
2. Connecting the television directly to the Audio /Video output of a Set-Top-Box will assure a more normal
picture.
36
BASIC OPERATION
IMPORTANT NOTES
No. Items Notes
1 Arching sound from A buzzing sound might be heard when the plasma display monitor is turned on in a very quiet
plasma display monitor’s room. This is due to the plasma panel drive circuit when it is functioning. This arching sound
panel. is normal and it is not a malfunction.
2 Interference for infrared Some infrared rays are emitted from the plasma display monitor’s panel that might affect other
equipment. infrared controlling equipment.
3 Bright and dark spots High-precision technology is used to manufacture the plasma display panel; But in some
cases, there are minor defects in some parts of the screen. Points that do not light, points
with brightness different from that of the periphery, points with color different from that of the
periphery, etc. Some pixels will always be on or always off. Please note that this is not a
malfunction.
4 Picture Image (Spectrum) When receving still picture signals, (e.g. channel number indication or clock indication) for a
while, you can see image-like when the picture varied. This is not a defect.
5 Display panel surface The plasma display panel is lighting the phosphors by the discharge of internal radiation. In
temperature is too high some cases, this may cause the temperature of the panel surface to increase. Please note
that this is not a malfunction. The Plasma TV surface temperature is higher than a
Cathode-ray-tube.
6 Plasma Surface The plasma panel is made from glass. Heavy shock on the front panel might damage it.
7 Transportation When the PDP monitor is transported horizontally, the glass panel has the possibility of being
broken or increasing the picture defects. At the time of transportation, horizontal style is
prohibited. More-over, please treat the plasma panel with great care because of a precision
apparatus. Please instruct transporters so that it should be put into the packing box at the time
of shipment.(There is a possibility that breakage of the panel or defects will increase.)
Rough transportation might cause damage to the panel and pixel failure.
8 Image retention The plasma monitor illuminates phosphor to display images. The phosphor has a finite
illumination life. After extended periods of illumination, the brightness of the phosphor will be
degraded to such extent that stationary images would burn-in that part of the screen as
grayed-out images.
Tips to prevent such image retention are:
- Do not display images having sharp brightness differences or hi-contrast images, such as
monochrome characters and graphic patterns, for long.
- Do not leave stationary images appearing for long, but try to refresh them at appropriate
intervals of time, or try to move them using screen saver function.
- Turn down the contrast and brightness controls.
9 Luminosity and contrast PDP television has luminosity and low contrast compared with CRT television.
10 Granular spots When a screen is seen at point-blank range, a random fine grain may be visible to a dark part.
11 Disturbance to video If an apparatus (VCR, etc.) antenna line is arranged near the monitor, the image may shake,
apparatus or disturbance may be received.
12 Lip Sync There is some time lag betweeen the picture and the sound. You can see lip motion that is
delayed compared to the sound.
13 About the use Electric discharge/luminescence characteristic of the PDP panel also changes with peripheral
environment of PDP temperature. Moreover, since there is also high power consumption value, a specified
television (temperature) temperature environment is required.
14 Caution on prolonged Storing the plasma television for a period of more than 2 to 3 months without use might cause
storage an unstable picture when the set is turned on.
15 Operating Operating altitude: 800 to 1114hPa (6194ft to -2484ft). Operating temperature: 41˚F to 95˚F.
16 Storage Storage Altitude: 300 to 1114hPa (31,912 to -2484ft). Storage temperature: 5˚F to 140˚F.
17 Power ON or OFF Frequent use of the Power ON or OFF might trigger the power protection circuit. If the TV
does not turn ON, please wait a little before turning ON again.
37
DW2U
ADJUSTMENTS TABLE OF CONTENTS

TO GO TO A SECTION, CLICK ON ITS HEADING BELOW
1 Adjustment procedure start up....................................................................................................39
1.1 How to get into adjustment mode ................................................................................39

1.2 Changing data and selecting adjustment code............................................................39
2 Memory initialize ........................................................................................................................39

2.1 Memory initialize operation ..........................................................................................39
2.2 Factory and service adjustments ................................................................................40
3 Video Adjustment .......................................................................................................................40

3.1 Sub-Contrast & Clamp Adjustment ........................................................................................40
3.2 Brightness Check .........................................................................................................40
4 POWER SUPPLY Vs, Va Voltage Adjustment....................................................................................41
5 White balance adjustment ..........................................................................................................42

5.1 Video Color Temperature Adjustment (High) ..........................................................................42
5.2 Video Color Temperature Adjustment (Medium)..........................................................42
5.3 Video Color Temperature Adjustment (Standard) ........................................................43
5.4 Video Color Temperature Adjustment (Black and White) ............................................43
5.5 White Balance Adjustment OSD Flowchart Diagram ..................................................... 44
6 DIGITAL MAIN CHECK ............................................................................................................43
7 Screen Check ............................................................................................................................46
8 HDMI Adjustment ..................................................................................................................... 46
9 Settings for Delivery .................................................................................................................47

10 OSD Design Select .................................................................................................................. 50
38
TABLE OF CONTENTS
DW2U
1 ADJUSTMENT PROCEDURE START-UP

The 42HDT79 42HDS69 and 42HDX99 PDP TV sets Remote Control Buttons
pass through adjustment procedures during the assembly
process. These adjustments must be done to assure the Change
best performance of the PDP set for the consumer. Selection (Up)
Also, after servicing, these same adjustments must be Decrease Increase

Data Value Data Value
done. The adjustments are all made through the I2C bus
by changing data in the Adjustment mode menu. Change
Selection (Down)
Table 2 on pages 38-46 shows the complete parameter
list with a brief description, signal format, the adjustment
range and the initial data.
1.1 HOW TO GET TO ADJUSTMENT MODE

Chassis adjustment mode can be access by pressing
the R/C keys MENU + MENU + 8 + SELECT to enter
adjustment mode. For some parameters the only way
to see them is by selecting the parameter number than
pressed SELECT in order to see it; then DATA can be
change if other parameter needs to change then press
key then repeat the same procedure.
ADJUST MODE
FACT RESET
MEMORY INIT
RGB
WHITE BAL HIGH
WHITE BAL MED B. To make a selection, use the NUMBER pad on the PDP
WHITE BAL STD R/C ; example : select DEVICE press 69 then SELECT
WHITE BAL B/W the DATA shown is "EB" ; if this DATA needs to be change
press the , , keys to modify, when finish press SELECT
key to store the new DATA value.
Other way to access this mode is by use JIG R/C code: (9C Hex). normal condition.
To escape from Adjustment Mode press “INPUT” key on Side
panel or EXIT key of R/C to exit service adjustment mode. C. After finishing the necessary adjustment press the R/C
EXIT key or EXIT key on the side panel.
1.2 CHANGING DATA AND SELECTING ADJUSTMENT Adjustment mode is released and PDP set returns to
CODE normal condition.
When the PDP set is in adjustment mode, the cursor , ,
, and MENU keys of the remote control or front panel 2 MEMORY INITIALIZE
may be used as the adjustment keys. 2.1 MEMORY INITIALIZE OPERATION
A. Use any Hitachi remote control when making an NOTE: The execution of this function returns the
adjustment. adjustment codes to the preset values, therefore,
, keys are used for selecting adjustment item. adjustment data will be lost.
Procedure
(1) Enter Adjustment mode by the method described in
sub-items 1.1 and 1.2 from item 1 (“Adjustment
procedure start up”).
(2) Get to the second page of Adjust Mode by pressing
remote control “Menu” key once, or with either the
R/C or front panel , cursor keys several times.
(3) Select MEMORY INIT adjust code.
(4) Activate MEMORY INIT by pressing cursor key for
, keys are used for changing data values. more than 3 seconds.
MENU key is used to advance through the adjustment (5) Check the following process for initialization opera-
mode menus and pages. tion.
CH 5
39
BACK TO ADJUSTMENTS
DW2U
3.12 525i Cb,Cr Clamp offset adjustment

·Process of Memory Initialize operation. Preparation
① A screen is be colored cyan when MEMORY INIT (1) Change signal format from 525(480)p to 525(480)i.
start. (See Fig.2)
② A screen is be colored green when MEMORY INIT Adjustment
finish normally. (1) Select ‘RGB’ of Service Adj. Menu.
③ A screen is be colored red when MEMORY INIT Press for over 2 seconds and have it perform
finish abnormally. automatic adjustment. When it’s completed, ‘Auto
Adjusting’ on the screen will be disappeared.
(6) Do not unplug from AC outlet until this operation
is complete and do not perform any key operation
either, after this operation each factory setting and 100% White
all adjust mode data should reset to delivery settings V2 V1 V1=1Vpp
automatically. Black V2=0.7Vpp
(7) After Memory Initialize, it should be unplug AC cord.
Unplug and plug AC cord and then all settings and data Black White Format : 525(480)i
are updated. Fig.2 Adjustment signal for 525(480)i format

(8) When PDP turns ON , it will tune CH03 this is the
3.2 BRIGHTNESS CHECK
complete operation of Memory Initialize process.
Preparation
(1) Start checking 20 minutes or more after the power is
2.2 FACTORY AND SERVICE ADJUSTMENTS
turned ON.
The adjustment item that is affected by the memory (2) Receive the color bar signal.
initialize operation is shown below: (3) The vertical incident illumination on the screen
* JIG. R/C FACTORY PRESET CODE:92 should be 20 lux or less.
MEMORY INITIALIZE and FACTORY PRESET (4) Picture Format is 16:9 standard mode.
ITEM MEMORY
INITIALIZE
FACTORY RESET REMARKS
(5) Select Day mode and reset.
RGB(480p) ADJUST DATA NOT INITIALIZE NOT INITIALIZE
WHITE BALANCE SETTING NOT INITIALIZE NOT INITIALIZE
OTHER ADJUSTMENT MODE DATA INITIALIZE NOT INITIALIZE Checking Procedure
FACTORY RESET ITEM INITIALIZE INITIALIZE
CHANNEL LIST INITIALIZE INITIALIZE (1) Check the brightness as below.
DW-2
Can be seen at black A1*

Can be seen slightly from black A2*
Note: If set black level is NG, readjust item Sub
Contrast adj.
Measuring Conditions
10
Note: Perform pre heat-run for more than 20 min. before (1) At the signal electric field strength 75± dBm, the 0
adjusting. specification mentioned above should be satisfied.

(2) At the input electric field 46-106dB , there should be
3.1 Sub-Contrast & Clamp Offset Adjustment
no abnormality.
Preparation for adjustment
* From color bar pattern below.
(1) Pre-heat at least 2 min. before the Final Adjust.
(2) Recall user menu and select ‘Video’ඎ ‘Picture Mode’ඎ
‘Day(Dynamic)’ඎ ‘Reset’.
(3) Receive following signal into input3 or input4(Comp) input. 7 step gray scale
Adjustment procedure A7 A6 A5 A4 A3 A2 A1
3.11 525p Sub-Contrast, Y/Cb/Cr Clamp offset adjustment
(1) Receive following 525(480)p Signal.
100% White
V2 V1 V1=1Vpp White 100%
Black V2=0.7Vpp
Format : 525(480)p Color Bar Signal
Black White
Adjustment signal for 525(480)p format A4 has tolerance.

A4 can be between black and
(2) Go into Service Adj. Menu and select ‘RGB’ . Slightly from black.
(3) Press for over 2 seconds and have it perform
automatic adjustment. When it’s completed, ‘Auto
Adjusting’ on the screen will be disappeared.
40
BACK TO ADJUSTMENTS
DW2U
4. Vs, Va voltage adjustment

Item Power Unit Vs, Va Adjustment Adj. point Refer to following
Adjustment Preparations Adjustment Procedures Remarks
(1) Turn on the set and perform (1) Turn Vs ADJ to adjust Vs voltage Permissive level of voltage in
pre-heat run more than 1 min to be within r0.1V of the value sufficient time of heat-run
on burn-in screen. specified in the label on the panel. performed is:
Vs: withinr0.1V
(2) Receive full black pattern signal (2) Turn Va ADJ to adjust Va voltage Va: withinr0.2V
(or video silence signal; but the to be within r0.2V of the value
power will be automatically turned specified in the label on the panel. 42’’: Adjusted by
off after a few seconds by power manufacturing.
save function.) 55’’: Need to be adjusted.
(3) Connect voltmeter (which has an (3) Reconfirm that Vs voltage remains
error within 0.02V or less) leads within r0.1V of the specified value.
to Vs (or Va) and GND test points Readjust if it’s outside of the margin.
of the power unit.
[Label example] Label position (Reference)
: Upper left
<LOT>N6
Vs= 80.0V Va=60.0V If it’s hard to read the voltage
V윘=140.0V Vx=60.0V value because of the wiring
positions, write it down by a
marker at visible place in
advance.
42” ̪Never touch this VR ! Vs1㧦

(This is already adjusted.) Vs Coarse ADJ. VR
Vs2㧦
Vs Fine ADJ. VR
CN99㧦Vs/Va
Test pins
(1)pin: Va
(2)pin: Vs
(3)pin: GND
̪Never touch this VR ! (Va) ̪Never touch this VR ! ̪Never touch this VR !
(This is already adjusted.) (This is already adjusted.) (This is already adjusted.)
41
BACK TO ADJUSTMENTS
DW2U
5 WHITE BALANCE ADJUSTMENTS Remarks

(1) Color temperature should be adjusted under the
General Notes for White Balance condition in which the screen is the brightest, thus
(1) If the incident illumination is more than 20 lux, the initial value for adjustment is set to its maximum.
change the environment (location, lighting, etc.) and (2) Adjustment is made by reducing brightness only.
ensure it to be less than 20 lux. Reduce a bright color for adjustment.
(2) At least one of the color drive codes must stay at its (3) Video color temperature & Adjustment No. are the
maximum value, FFH. same, but addresses in the memory are different,
thus there’s no problem.
5.1 VIDEO COLOR TEMPERATURE ADJUSTMENT 5.2 VIDEO COLOR TEMPERATURE ADJUSTMENT
(HIGH) (MEDIUM)
Preparation 1 Preparation
(1) Set the output of signal generator to white raster. (1) Same as “Video Color Temperature adjustment:
(Ratio:100%) (HIGH)”. For 55” the video level changes to
(2) Component signal 42” 55” 0.700Vp-p.
Video level: 0.700Vp-p 0.280Vp-p
SYNC: 0.300Vp-p 0.286Vp-p Adjustment
Set-up level: 0V 0V (1) Perform the following adjustment with the remote
(3) Input white raster signal into COMPONENT input control.
terminal of the PDP set. (2) Set the CRT color analyzer (CA-100) at the center of
(4) Set user control to Day mode. (Picture Mode) the panel.
(5) Confirm that the mode is set as “Factory Setting (3) Set color temperature to “MEDIUM”, using SEL key.
Mode”. (4) Ensure that Adjustment R/G/B DRIVE (MEDIUM) are
(6) Aspect: Video: Expanded all set as FF.
(5) After receiving White raster signal, step down the two
(or one) among Adjustment R/B/G DRIVE (MEDIUM)
and adjust the value shown below.
Specification
Video Color temperature (MED)
42"
Adjustment x = 0.285 ± 0.005
(1) Perform the following adjustment with the remote y = 0.293 ± 0.005
control. (Color temp: 9300K )
(2) Set the CRT color analyzer (CA-100) at the center of 55"
the panel. x = 0.285 ± 0.005
(3) Set color temperature to “HIGH”. y = 0.293 ± 0.005
(4) Ensure that Adjustment R/G/B DRIVE (HIGH) are all (Color temp: 9300K )
set as FF.
(5) After receiving White raster signal, step down the two At least one of the data should be FF.
(or one) among Adjustment R/G/B DRIVE (HIGH)
and adjust the value shown in the following:
Specification
Video Color temperature (HIGH)
42"
x = 0.273 ± 0.005
y = 0.273 ± 0.005
(Color temp: 12000K)
55"
x = 0.273 ± 0.005
y = 0.273 ± 0.005
(Color temp: 12000K)
At least one of the data should be FF.
42
BACK TO ADJUSTMENTS
DW2U
5.3 VIDEO COLOR TEMPERATURE ADJUSTMENT 6. DIGITAL MAIN CHECK

(STD)
Preparation 6.1 SYSTEM SOFTWARE VERSION CHECK
(1) Same as “Video Color Temperature adjustment:
(HIGH)”. For 55” video level changes to 0.700Vp-p. (1) Press Menu button on the R/C or control
panel.
Adjustment
(1) Perform the following adjustment with the remote (2) Enter the SETUP options, and then look
control. for UPGRADES option.
(2) Set the CRT color analyzer (CA-100) at the center of (3) The Main software version will be display
the panel. V0100.0000 as shown on Fig. 1.
(3) Set color temperature to “STD”. (4) If this version needs to be change for a
(4) Ensure that Adjustment R/G/B DRIVE (STD) are all design improvement or failure, please
set as FF. select the Upgrade Now button.
(5) After receiving White raster signal, step down the two
(or one) among Adjustment R/B/G DRIVE (STD) and Fig. 1 Software version
adjust the value shown below.
Specification
Setup
Reset The Software
Video Color temperature (STD) OR Software Version # : Main Vxxxx.xxxx
42"
MMC Software Upgrade
x = 0.314 ± 0.005
Upgrade Now
Please Insert MMC card before upgrading.
y = 0.327 ± 0.005 Reset TV Settings
No Yes
(Color temp: 6500K ) Please (Select
Insert MMC
"Yes" card
to return all settings to the factory
default after main power OFF/ON.)
55"
x = 0.314 ± 0.005 ove Return
Move SEL Return
y = 0.327 ± 0.005
(Color temp: 6500K ) (5) The upgrading process begin by filling a
bar, when finish the message will say,
“Upgrade complete …” when this appear
5.4 VIDEO COLOR TEMPERATURE ADJUSTMENT unplug the TV from the AC line outlet to
(B/W) (Only for HDX models) complete the process.
Preparation (6) Now plug again the TV and verify the
(1) Same as “Video Color Temperature adjustment: new software version.
(HIGH)”. For 55” video level changes to 0.700Vp-p. (7) The Main software version will display the
Adjustment latest version issue by design.
(1) Perform the following adjustment with the remote
control. NOTE:
(2) Set the CRT color analyzer (CA-100) at the center of
the panel. (1) A Service Bulletin will be sent when a
(3) Ensure that Adjustment R/G/B DRIVE (B/W) are all new version is issued officially to the
set as FF. Service Department every time the soft-
(4) After receiving White Raster signal, step down the ware version needs to be modified.
two (or one) among Adjustment R/B/G DRIVE (B/W)
(2) In case that the upgrade fails or when a
and adjust the value shown below.
CARD is inserted with new version and
Specification can’t upgrade ; please perform the
Video Color temperature (B/W) FACTORY RESET process to the TV,
42" then try upgrading again.
x = 0.335 ± 0.005
y = 0.343 ± 0.005
(Color temp: 5400K )
55"
x = 0.335 ± 0.005
y = 0.343 ± 0.005
(Color temp: 5400K )

Remarks
(1) Same as “Video Color Temperature adjustment
(HIGH)”
43
BACK TO ADJUSTMENTS
DW2U
5.5 WHITE BALANCE ADJUSTMENT OSD FLOW DIAGRAM

5.5.1 Adjustment OSD Flowchart
(1) Adjust Mode OSD
JIG R/C code:9C or Press [MENU]+[MENU]+[8]+[SELECT] of Control panel.
MENU
+
MENU
+
8
+
SELECT
JIG Code
CH U/D, INPUT
CYAN*
ADJUST MODE
FACT RESET GREEN : Finish Normally
MEMORY INIT
RGB Press for 2 seg.
WHITE BAL HIGH RED
: Finish Abnormally
WHITE BAL MED
WHITE BAL STD
WHITE BAL B/W

ًٕ CH U/D, INPUT
ADJUST MODE MAGENTA

FACT RESET
MEMORY INIT
GREEN : Finish Normally
WHITE BAL HIGH
WHITE BAL MED RED : Finish Abnormally
WHITE BAL STD
WHITE BAL B/W

ًٕ
CH U/D, INPUT

ADJUST MODE
FACT RESET
MEMORY INIT
WHITE BAL HIGH
WHITE BAL MED
WHITE BAL STD EXIT
WHITE BAL B/W

ًٕ

CH 3
44
BACK TO ADJUSTMENTS
DW2U
5.7.1 Adjustment OSD Flowchart (Cont.)
ًٕ CH U/D, INPUT
ADJUST MODE
FACT RESET G DRV HIGH **
MEMORY INIT R DRV HIGH **
RGB B DRV HIGH **
WHITE BAL HIGH
WHITE BAL MED
WHITE BAL STD
WHITE BAL B/W
ًٕ Press EXIT key Select DRV

ًٕ and Press → key
CH U/D, INPUT
G DRV **

ADJUST MODE R DRV **
FACT RESET
MEMORY INIT **
RGB B DRV
WHITE BAL HIGH
WHITE BAL MED
WHITE BAL STD
WHITE BAL B/W

WHITE BALANCE
ADJUST MODE
VIDEO SETTINGS
(1) CONTRAST ; MAX
(2) COLOR,TINT,SHARP,BRIGHT ; CENTER
(3) COLOR TEMP ; HIGH
ADJUST
(1) Press ↑↓ to Select the G DRV,R DRV,
B DRV.
(Initial value R/G/B DRV : FF)
(2) Press ← →to adjust
CH 3
45
BACK TO ADJUSTMENTS
DW2U
7. SCREEN CHECK 8. HDMI adjustment

Preparation a. DVI compatibility check
(1) Set AC120±1V. Preparation
(2) Turn on the power and leave it more than 5 min. 1. Prepare HDTV signal generator. (Zenith HD-SAT520)
(3) Receive circle pattern at 4:3 Expanded mode. 2. Select DVI mode then 1080i format
(4) Input 480p and 1080i circle pattern into Component 3. Connect HDMI-DVI cable to the HDMI input on the
video 3. (ASPECT 16:9 Standard) PDP set.
ATSC
Checking DVI - HDMI

conversion cable
(1) Receive RF, 480p and 1080i signal, then check Set Top Box
the following items 1~4:

1. Check the symmetry of the pattern (right/left).
2. Check the horizontal position and the balance
(right/left). b. DVI/HDCP/Timing (Display Position) Check
3. Check the symmetry of the pattern (top/bottom). 1. Set 1080i crosshatch with black background,
4. Check the vertical position and the balance with a small color bar and small multi-burst.
(top/bottom). (Confirm that the picture appears as shown
below or similar)
2. Press “INFO” button on remote control to
3 confirm that “1080i Format” indication appears.
3. Confirm that Horizontal and Vertical position
meet the following spec.
C has s is DW 2 unit
Screen Size 42” 55” inch
a 48¢8 58¢8
b 45¢8 55¢8
mm
c 58¢5 73¢5
d 56¢5 68¢5
Aspect 16:9 Standard 16:9 Standard
Remarks
A B
SCREEN
0 1 2 2 1 0
d
a b
9. FACTORY RESET
After all of the adjustments of main chassis are finished,
perform FACTORY RESET.
SIGNAL ASPECT SPEC(A,B) (1) Enter Adjustment Mode by the method described in
Hitachi circle pattern 16:9 Standard1 0 +/- 0.5 sub-items 1-1 and 1-2 from page 30. (“Adjustment
Procedure Start-up”).
(2) From the first menu in Adjustment Mode, select
FACT RESET adjustment code.
(3) Activate FACT RESET by pressing “Right” cursor
key once.
(4) Other procedure to acces the FACTORY RESET is by
sending the 92 hex code with a programable R/C.
(5) The procedure of the FACTORY RESET process is
the following and the DATA table is shown next.
46
BACK TO ADJUSTMENTS
DW2U
·Process of FACTORY RESET operation.

① A screen is colored magenta when FACTORY RESET
start.
② A screen is colored green when FACTORY RESET
finish normally.
③ A screen is colored RED when FACTORY RESET
finish abnormally.
(6) After FACTORY RESET, it should be unplug AC
cord.Unplug and plug AC cord and then all settings
and data are updated.
(7) When PDP turns ON , it will tune CH03 this is the
complete operation of FACTORY RESET process.
9 . DATA TABLE OF SETTING FOR DELIVERY
USER Control Initialization
Settings for delivery (FACTORY RESET)
Function Initial Data Condition 42HDS69 42HDT79 42HDX99

55HDS69 55HDT79 55HDX99
Input Mode Air X X X

Channel 03-1ch X X X
Favorite Channels Not Registered X X X
PIP On/Off Off X X X
PIP Mode SPLIT X X X
POP Position Middle Right X X X
PIP Position Bottom Right X X X
Freeze Mode Main Freeze X X X
(1pix)
Master Volume 20 Step X X X
Video
Picture Mode Dynamic X X X
Contrast(White Lebel) 100% X X X
Brightness(Black Lebel) 50% X X X
Color 50% X X X
Tint CENTER X X X
Sharpness 50% X X X
Color Temperature High X X X
Black Enhancement High X X X
Contrast Mode Dynamic X X X
Noise Reduction Low X X X
Auto Movie Mode Off X X X
Color Management 웎 X X 웎
Color Decoding 웎 X X 웎
Auto Color Off X X 웎
White Balance 웎 X X 웎
Aspect
Auto Aspect Off X X X
Mode 4:3 Expanded X X X
16:9 Standard1
Vertical Position 0 X X X
Black Side Panel Off X X X
Reset Video Settings 웎 X X X
47
BACK TO ADJUSTMENTS
DW2U
9. SETTING for Delivery (continued)

55HDS69 55HDT79 55HDX99
Audio
Treble 50% X X X
Bass 50% X X X
Balance CENT X X X
Surround Off X X X
Bass Boost On X X X
Audio Source Stereo Analog Broadcast X X X
Internal Speakers On X X X
Auto Noise Cancel Off Analog Broadcast X X X
Perfect Volume Off X X X
Loudness Off X X X
Language 1 (English) DTV X X X
Digital Output Dolby Digital DTV X X X
DRC On DTV X X X
Channel Manager
Signal Meter
Channel 웎 X X X
Strength 웎 X X X
Peak 웎 X X X
SNR 웎 X X X
Auto Channel Scan
Source Air X X X
Reset 웎 X X X
Start 웎 X X X
Channel List
FAV Not Set X X X
CH# Air/Cable:2-13CH X X X
Scan On X X X
Lock Off X X X
ID 웎 X X X
Locks
Change Access Code “0000”,”7777” X X X
Engage Lock
Set Channel Lock Not Set X X X
Set Front Panel Lock Not Set X X X
Movie Ratings Not Set X X X
TV Ratings Not Set X X X
Canadian Ratings (Eng.) Not Set X X X
Canadian Ratings (Frn.) Not Set X X X
Alternate Ratings U.S. X X X
Timers
Set the Clock
Time Zone PST X X X
Date Jan 2006 01 X X X
Time Not Registered X X X
Automatically Adjust off X X X
Clock for Daylight
Savings Changes.
Set Sleep Timer Not Set X X X
Set Day/Night Timer
Activate off X X X
Day Mode On 6:00 AM X X X
Day Mode Off 6:00 PM X X X
Set Event Timer Not Set 웎 㧙 X
48
DW2U
9. SETTING for Delivery (continued)

55HDS69 55HDT79 55HDX99
Setup
Menu Preference
Set The Language English X X X
Set The Menu Background Shaded X X X
Set The Screen Saver
Main Picture Moving Option 1 X X X
Image Power Max X X X
Screen Wipe Wipe X X X
Automatic Power Saving Yes X X X
Set The Inputs
Input1 Rename None X X X
Input4 Auto Link Off X X X
(Auto/Remote/Off)
Set the AV Net (Wizard will be X 웎 웎
starting.)
Set Closed Caption
Caption Display Auto X X X
Mode Captions X X X
(Captions/Text)
Channel (1/2/3/4) 1 X X X
Digital Captions
Language 1 (English) X X X
Font Default X X X
(Default/1/2/3/4/5/6/7/8)
Size Standard X X X
(Small/Standard/Large)
Style Standard X X X
(Standard/High Visibility)
Set The Output Terminals
Video Out Monitor X X X
(TV Tuner Out / Monitor)
Audio Out Fixed X X X
(Fixed/Variable)
IR Out Extended Length X X 웎
Set The Quick Start Options off X X X
Reset The Software
MMC Software Upgrade X X X
Reset TV Settings No X X X
Power Swivel Locked X X 웎
49
DW2U
10 OSD Design Select
Adjustment Preparation
(1) Go to the Adjust Mode Menu.
(2) Select “DEVICE” in the Adjust Mode Menu as follows. DEVICE menu
(3) Press [ ] button to access the DEVICE menu.
ADJUST MODE ADJUST MODE
IR BLAST DEVICE ITEM DATA
CLOCK TEST 0 2 002
MAINTENANCE
DEVICE
M306H3 V01.00
ADJ.REV V01.00
PANEL TIME 265
࡮DEVICE : Press 0 button. And press SELECT button to set.

࡮ITEM : Press 2 button. And press SELECT button to set.
࡮DATA : Press [ًٕ]buttons to select as follows. And press SELECT button to set.
DATA=2웛DIREC웉Directors Model웊

DATA=1웛A웉Regional Model웊

DATA=0웛B웉National Model웊

(4) Unpluged and pluged to update the OSD Design.
Adjustment Procedure
(1) According to a list shown below, select an OSD design.
Class Model DATA OSD Design

X 42/55HDX99 ',5(&웛'LUHFWRUV
T 42/55HDT79 $웛5HJLRQDO
S 42/55HDS69 %웛1DWLRQDO
50
BACK TO ADJUSTMENTS
DW2U
TROUBLESHOOTING FLOW CHARTS

TROUBLE SHOOTING for DIGITAL MODULE (Device error check)
Digital Main P.W.B has five LED (KNIGHT RIDER) on board.

After Power ON these LED will be turned on in sequence as follows.
It may take a few seconds for the sequence.
LED sequence
Sequence D205 D204 D203 D202 D201
(Red) (Green) (Yellow) (Orange) (Red)
<PiO04> <PiO03> <PiO02> <PiO01> <PiO00>
1 (Start) ○ ○ ○ ○ ●
2 ○ ○ ○ ● ●
3 ○ ○ ● ● ●
4 ○ ● ● ● ●
5 (End) ○ ○ ○ ○ ○
○ is turn off the LED, ● is Lighting the LED
After Program is loaded without error, all LED will be turned off.
Any LED should not light.
If some errors occur, LED will show the error pattern.
(1) Check that LED is not lit.

(2) If LED is lit, refer to the following table and check the involved devices.
(42” only)
Location of LEDs
Digital Main Board
LED5 (D205) LED1(D201)

LED4 (D204) LED2 (D202)
LED3 (D203)
51
TABLE OF CONTENTS
DW2U
TROUBLESHOOTING FLOWCHARTS
LED patterns for involved devices

No. LED5 LED4 LED3 LED2 LED1 Device Circuit No Remarks
(Orange)
(Yellow)
(Green)
(Red)
(Red)
D205
D204
D203
D202
D201
1 ○ ○ ○ ○ ○ －－ No Error
2 Digital Tuner Video/Audio of Cable/Air

○ ○ ○ ○ ●
3 Analog Tuner Video/Audio of Cable/Air

○ ○ ○ ● ○
4 ○ ○ ● ○ ○ MPEG(Seine2) Video/Audio of Cable/Air
5 ○ ○ ● ○ ● Graphics(Seine2) All OSD
6 ○ ○ ● ● ○ Flash Memory Loading Program
7 ○ ○ ● ● ● I2C(Seine2)
8 ○ ● ○ ○ ○ IEEE1394
9 ○ ○ ○ ● ● DEMUX(Seine2)
10 (42”○only) ● ○ ● ○ －－ (42” only)
11 ○ ● ○ ● ● －－
12 ○ ● ● ○ ○ －－
13 ○ ● ● ○ ● －－
14 ○ ● ● ● ○ －－
15 ○ ● ● ● ● －－
16 ● ○ ○ ○ ○ －－
17 ● ○ ○ ○ ● PDP Panel
18 ● ○ ○ ● ○ Sub Micro
19 ● ○ ● ○ ● Seine OSD
20 ● ● ● ● ○ DDR SDRAM
○ is turn off the LED, ● is lighting the LED.
52
DW2U
CIRCUIT BLOCK DIAGRAM
[42/55HDS69]
Scan Driver
Scan Driver
X Sustain Circuit Y Sustain Circuit
Address Driver
Driver Controller Logic Control

unit
Data Controller
LVDS Receiver Signal Controller

PDP Panel Module
FAN FAN
(42” only) (42” only)
Vcego CPUgo RGB

Filter PWB Vsago PDPgo (LVDS)
Power
AC Main
Inlet Power SW Supply Power2
Main-Digital PWB
Unit Power1
Sub PLD DC-DC
POD PWB Side
HDMI PWB
Micro (Stehano) Conv. PLD Terminal
Equalizer A/V (Oberon) PWB
Sub PWB Seine2 Seine2 VCXO
POD
A/V
Control A-chip D-chip PLL
Digital/ Card
PWB Analog
Video Audio I/F
SW SW
Key SW Tuner DDR2
DC-DC
Demodulator A/V (POD-Vcc)
Pin Jack
Speaker R
Speaker L
Woofer R
Woofer L
Audio Audio Digital SD/MMC

DSP DAC Audio Card
RS-232C
Amplifier I/F
OPT-Audio
Output
Remote
Control LED PWB
IR LED
Receiver
Swivel Stand
53
TABLE OF CONTENTS
DW2U
[42/55HDT79]
Scan Driver
Scan Driver
Address Driver

unit
Data Controller

PDP Panel Module
FAN FAN
(42” only) (42” only)
Vcego CPUgo RGB

Power
AC Main
Main-Digital PWB Photo
Unit Power1
Sub PLD DC-DC
POD PWB Side
HDMI PWB
POD
A/V
Digital/ Card
PWB Analog
Video Audio I/F
SW SW
Key SW Tuner DDR2
DC-DC
Pin Jack
Speaker R
Speaker L
Woofer R
Woofer L
Audio Audio Digital SD/MMC

DSP DAC Audio Card
RS-232C
Amplifier I/F
IR Out
OPT-Audio Motor
Output Driver
Remote
Control LED PWB
IR IrDA LED
Receiver Receiver
Swivel Stand
54
TABLE OF CONTENTS
DW2U
[42/55HDX99]
Scan Driver
Scan Driver
Address Driver

unit
Data Controller

PDP Panel Module
FAN FAN
(42” only) (42” only)
Vcego CPUgo RGB

Power
AC Main
Main-Digital PWB Photo
Unit Power1
Sub PLD DC-DC
POD PWB Side
HDMI PWB
POD
A/V
Digital/ Card
PWB Analog
Video Audio I/F
SW SW
Key SW Tuner IEEE DDR2
1394 DC-DC
Pin Jack
Speaker R
Speaker L
Woofer R
Woofer L
UEI Audio Audio Digital SD/MMC

DSP DAC Audio Card
RS-232C
Amplifier I/F
IR-Blaster
Driver
OPT-Audio Motor
Output Driver
Remote
Control LED PWB
IR IrDA LED
Receiver Receiver
Swivel Stand
55
TABLE OF CONTENTS
DW2U
POWER SYSTEM BLOCK DIAGRAM
AC120V
PDP Panel Module
Filter PWB Power Supply Unit Vs (+80V)
Va (+60V)
(PFC)
Vcc (+5.1V)
AC STBY+5V
SW
+12V +10.5V +5.6V STBY+3.3V (+3.3V)
+5V +3.3V +1.3V +1.8V +3.3V +9V +9V +3.3V

Reg. DC-DC DC-DC DC-DC Reg. Reg. Reg. Reg.
Sync. Digital +1.3V +2.5V +2.5V LPF Audio DAC

sep. Audio Reg. Reg. Reg.
Amp.
Seine2-D DDR2 +5V +3.3V

FLASH +1.5V Reg. Reg.
EPLD Reg.
+2.5V +3.0V
Reg. Reg. Seine2-A USB Audio Sub
+1.5V MICRO
ADC
Reg.
Audio VCXO
IEEE1394 DSP PLL Main-Digital PWB
+3.3V +1.0V +5V +9V +9V

Reg. DC-DC Reg. Reg. Reg.
Swivel
Swivel
Motor
Stand
+5V +5V +1.8V AV SW Buffer Driver
+3.3V Reg. Reg. Reg.
Reg.
IR-Blaster
OPT Tuner Demodulator +3.3V +3.3V Vari.
Cable- Driver
Output AGC Reg. DC-DC Reg.
Equalizer OOB Vari.
Reg.
HDMI PWB Sub-Digital PWB +2.5V
Reg.
FAN FAN
+1.2V
IR receiver Reg. POD- POD-
LED Vcc Vpp
SD
LED PWB MMC FPGA POD PWB
56
DW2U
AUDIO CIRCUIT BLOCK DIAGRAM
I2S IF09 IF11

Woofer L
IF15
WM8520 TPA3100
I2S I2S
DAC Digital
NJU26107 Woofer R
IF20 Volume Mute
W/amp Power Amp.
Seine SN74LV Balance
C244AP Bass/Treble
W Surround IF10 IF12 Speaker L
Bass Boost WM8520 TPA3100
AGC DAC Digital
W/amp Power Amp. Speaker R
57
DW2U
CONNECTION DIAGRAM
㪧㫆㫎㪼㫉㩷㪪㫌㫇㫇㫃㫐㩷㪬㫅㫀㫋㪧㪘㪥㪜㪣
㪚㪥㪍㪋㪚㪥㪉㪊
㪭㪟㪄㪈㪇㪧㪭㪟㪄㪈㪇㪧
㪭㪸㩿㪍㪇㪭㪀㪈㪈㪭㪸㩿㪍㪇㪭㪀
㪥㪚㪉㪉㪥㪚
㪭㪺㪺㩿㪌㪅㪈㪭㪀㪊㪊㪭㪺㪺㩿㪌㪅㪈㪭㪀
㪞㪥㪛㪋㪋㪞㪥㪛
㪞㪥㪛㪌㪌㪞㪥㪛
㪞㪥㪛㪍㪍㪞㪥㪛
㪥㪚㪎㪎㪥㪚
㪭㫊㩿㪏㪇㪭㪀㪏㪏㪭㫊㩿㪏㪇㪭㪀
㪭㫊㩿㪏㪇㪭㪀㪐㪐㪭㫊㩿㪏㪇㪭㪀
㪭㫊㩿㪏㪇㪭㪀㪈㪇㪈㪇㪭㫊㩿㪏㪇㪭㪀
㪚㪥㪍㪏㪚㪥㪍
㪧㪟㪄㪐㪧㪧㪟㪄㪐㪧
㪭㪺㪺㩿㪌㪅㪈㪭㪀㪈㪈㪭㪺㪺㩿㪌㪅㪈㪭㪀
㪞㪥㪛㪉㪉㪞㪥㪛
㪭㫇㫉㪉㩿㪪㪫㪙㪊㪅㪊㪭㪀㪊㪊㪭㫇㫉㪉㩿㪪㪫㪙㪊㪅㪊㪭㪀
㪭㫉㪸㪌㪌㪭㫉㪸
㪭㫉㫊㪍㪍㪭㫉㫊
㪭㪺㪼㪾㫆㪎㪎㪭㪺㪼㪾㫆
㪭㫊㪸㪾㫆㪏㪏㪭㫊㪸㪾㫆
㪝㪠㪣㪫㪜㪩㩷㪧㪮㪙㪧㪝㪚㪾㫆㪐㪐㪧㪝㪚㪾㫆
㪧㪧㪬㪈㪚㪥㪍㪈
㪭㪟㪄㪍㪧㪭㪟㪄㪍㪧
㪘㪚㩿㪣㪀㪈㪈㪘㪚㩿㪣㪀
㪥㪚㪉㪉㪥㪚
㪘㪚㩷㪠㪥㪘㪚㩿㪥㪀㪊㪊㪘㪚㩿㪥㪀
㪥㪚㪋㪋㪥㪚
㪥㪚㪌㪌㪥㪚
㪥㪚㪍㪍㪥㪚
㪤㪸㫀㫅㩷㪛㫀㪾㫀㫋㪸㫃㩷㪧㪮㪙
㪚㪥㪍㪊㪧㪧㪤㪈
㪜㪟㪄㪏㪧㪱㪟㪄㪇㪏㪟
㪪㪫㪙㪂㪌㪅㪇㪭㪈㪈㪪㪫㪙㪂㪌㪅㪇㪭
㪪㪫㪙㪂㪊㪅㪊㪭㪊㪊㪪㪫㪙㪂㪊㪅㪊㪭
㪧㫆㪮㪜㪩㫆㪝㪝㪋㪋㪧㫆㪮㪜㪩㫆㪝㪝
㪘㪚㪚㪣㫆㪚㪢㪌㪌㪘㪚㪚㪣㫆㪚㪢
㪧㫆㪮㪜㪩㪈㪍㪍㪧㫆㪮㪜㪩㪈
㪧㫆㪮㪜㪩㪉㪎㪎㪧㫆㪮㪜㪩㪉
㪧㫆㪮㪜㪩㪊㪏㪏㪧㫆㪮㪜㪩㪊
㪚㪥㪧㪧㪪㪧㪧㪤㪉
㪜㪟㪄㪈㪌㪧㪛㪝㪊㪛㪄㪈㪌㪟
㪂㪌㪅㪍㪭㪈㪈㪂㪌㪅㪍㪭
㪂㪌㪅㪍㪭㪉㪉㪂㪌㪅㪍㪭
㪂㪌㪅㪍㪭㪊㪊㪂㪌㪅㪍㪭
㪞㪥㪛㪌㪌㪞㪥㪛
㪂㪈㪇㪭㪎㪎㪂㪈㪇㪭
㪞㪥㪛㪏㪏㪞㪥㪛
㪂㪈㪍㪭㪐㪐㪂㪈㪍㪭
㪞㪥㪛㪈㪇㪈㪇㪞㪥㪛
㪞㪥㪛㪈㪈㪈㪈㪞㪥㪛
㪞㪥㪛㪈㪉㪈㪉㪞㪥㪛
㪂㪈㪉㪭㪈㪊㪈㪊㪂㪈㪉㪭
㪂㪈㪉㪭㪈㪋㪈㪋㪂㪈㪉㪭
㪂㪈㪉㪭㪈㪌㪈㪌㪂㪈㪉㪭
㪜㪚㪇㪈㪚㪥㪈
㪣㪭㪛㪪㪋㪈㪄㪚㪦㪥㪥㪜㪛㪝㪈㪊㪄㪊㪇㪛㪪
㪣㪚㪛㪶㪞㫆㪈㪈㪩㪘㪄
㪙㪣㪶㫆㪥㪉㪉㪞㪥㪛㩿㪣㪭㪛㪪㪀
㪠㪄㪧㪮㪤㪊㪊㪩㪘㪂
㪪㫌㪹㩷㪧㪮㪙㪙㪣㪶㫀㪥㪪㪫㪋㪋㪪㪚㪣
㪞㪥㪛㪌㪌㪩㪙㪄
㪦㪧㪫㩷㪧㪮㪙㪡㪤㪪㪬㪆㪧㪪㪤㪞㪥㪛㩿㪣㪭㪛㪪㪀㪎㪎㪩㪙㪂
㪌㪇㪈㪋㪐㪊㪄㪉㪇㪇㪭㪧㪆㪌㪇㪈㪋㪐㪎㪄㪉㪇㪇㪭㪪㪫㪘㪈㪄㪏㪏㪪㪛㪘
㪧㪮㪪㪧㪫㪮㪈㪞㪥㪛㪞㪥㪛㪉㪫㪘㪈㪂㪐㪐㪩㪚㪄
㪌㪉㪋㪈㪏㪄㪇㪎㪟㪪㪄㪛㪌㪊㪉㪐㪇㪄㪇㪎㪭㪧㪄㪛㪊㪂㪌㪅㪍㪭㪛㪂㪊㪅㪊㪭㪋㪞㪥㪛㪈㪇㪈㪇㪞㪥㪛㩿㪣㪭㪛㪪㪀
㪪㪆㪧㪛㫀㪫㪈㪈㪪㪆㪧㪛㫀㪫㪌㪂㪌㪅㪍㪭㪛㪂㪊㪅㪊㪭㪍㪫㪙㪈㪄㪈㪈㪈㪈㪩㪚㪂
㪩㪞㪙㪂㪌㪭㪉㪉㫀㪩㪂㪌㪭㪎㪂㪌㪅㪍㪭㪛㪂㪊㪅㪊㪭㪏㪫㪙㪈㪂㪈㪉㪈㪉㪚㪧㪬㪞㪦
㪞㪥㪛㪊㪊㪞㪥㪛㪐㪂㪌㪅㪍㪭㪞㪥㪛㪈㪇㪞㪥㪛㩿㪣㪭㪛㪪㪀㪈㪊㪈㪊㪩㪚㪣㪢㪄
㪤㫆㪫㫆㪩㪂㪋㪋㪤㫆㪫㫆㪩㪂㪈㪈㪞㪥㪛㪞㪥㪛㪈㪉㪫㪚㪈㪄㪈㪋㪈㪋㪧㪛㪧㪞㪦
㪤㫆㪫㫆㪩㪄㪌㪌㪤㫆㪫㫆㪩㪄㪈㪊㪪㪙㪰㪂㪌㪅㪇㪭㪪㪙㪰㪂㪊㪅㪊㪭㪈㪋㪫㪚㪈䋫㪈㪌㪈㪌㪩㪚㪣㪢㪂
㪡㫆㫀㪥㪫㪛㪜㪫㪍㪍㪡㫆㫀㪥㪫㪛㪜㪫㪈㪌㪞㪥㪛㪞㪥㪛㪈㪍㪞㪥㪛㪈㪍㪈㪍㪠㪩㪨
㪪㪮㪶㪚㫆㪤㪎㪎㪪㪮㪶㪚㫆㪤㪈㪎㪂㪈㪍㪭㪂㪈㪇㪭㪈㪏㪫㪚㪣㪢㪈㪄㪈㪎㪈㪎㪩㪛㪄
㪈㪐㪞㪥㪛㪪㪮㫀㪭㪜㪣㪶㪞㪉㪇㪫㪚㪣㪢㪈㪂㪈㪏㪈㪏㪧㪛㪮㪥
㪉㪈㫀㪩㪶㫀㪥㪤㪘㫀㪥㪶㪰㪆㪭㪉㪉㪞㪥㪛㪈㪐㪈㪐㪩㪛㪂
㪉㪊㫀㪩㫆㪬㪫㪞㪥㪛㪉㪋㪫㪛㪈㪄㪉㪇㪉㪇㪞㪥㪛㩿㪣㪭㪛㪪㪀
㪉㪌㫀㪩㫆㪝㪝㪤㪘㫀㪥㪶㪰㪶㪜㪉㪍㪫㪛㪈㪂㪉㪈㪉㪈㪩㪜㪄
㪝㪘㪥㪉㪎㪟㪧㪶㪛㪜㪫㪞㪥㪛㪉㪏㪞㪥㪛㪉㪉㪉㪉㪞㪥㪛
㪉㪐㪝㫀㪥㪤㪘㫀㪥㪶㪧㪙㪊㪇㪫㪜㪈㪄㪉㪊㪉㪊㪩㪜㪂
㪧㪝㪘㪈㪊㪈㪩㫀㪥㪞㪥㪛㪊㪉㪫㪜㪈㪂㪉㪋㪉㪋㪞㪥㪛
㪱㪟㪄㪇㪊㪟㪊㪊㪚㪧㪛㪜㪫㪤㪘㫀㪥㪶㪧㪩㪆㪚㪊㪋㪞㪥㪛㪉㪌㪉㪌㪞㪥㪛
㪭㪚㪚㪈㪈㪭㪚㪚㪊㪌㪪㪮㪭㪣㪛㪜㪫㪞㪥㪛㪊㪍㪙㫀㪫㪇㪉㪉㪍㪉㪍㪞㪥㪛
㪣㫆㪚㪢㪉㪉㪣㫆㪚㪢㪊㪎㪞㪥㪛㪪㪬㪙㪶㪰㪆㪭㪊㪏㪙㫀㪫㪇㪈㪉㪎㪉㪎㪞㪥㪛
㪞㪥㪛㪊㪊㪞㪥㪛㪊㪐㪘㪜㪧㪶㪩㪞㪥㪛㪋㪇㪙㫀㪫㪇㪇㪉㪏㪉㪏㪞㪥㪛
㪋㪈㪘㪜㪧㪶㪣㪪㪆㪧㪛㫀㪫㪋㪉㪪㪚㪣㪉㪐㪉㪐㪞㪥㪛
㪋㪊㪞㪥㪛㪞㪥㪛㪋㪋㪪㪛㪘㪊㪇㪊㪇㪞㪥㪛
㪋㪌㪘㪪㪧㪶㪩㪪㪛㪶㪰㫆㪋㪍㪩㪯㪛㪊㪈
㪋㪎㪘㪪㪧㪶㪣㪞㪥㪛㪋㪏㪫㪯㪛㪊㪉
㪝㪘㪥㪋㪐㪞㪥㪛㪪㪛㪶㪚㫆㪌㪇㪚㪫㪪㪊㪊
㪌㪈㪞㪥㪛㪌㪉㪩㪫㪪㪊㪋
㪧㪝㪘㪈
㪧㪝㪘㪉㪌㪊㪞㪥㪛㪌㪋㪧㪥㪣㪩㪪㪫㪊㪌
㪱㪟㪄㪇㪊㪟㪌㪌㪪㪜㪣㪶㪣㪶㪪㪌㪍㪧㪥㪣㫆㪥㪊㪍
㪭㪚㪚㪈㪈㪭㪚㪚㪌㪎㪪㪜㪣㪶㪩㪶㪪㪞㪥㪛㪌㪏㪫㪜㪤㪧㪶㪘㪣㪫㪊㪎
㪣㫆㪚㪢㪉㪉㪣㫆㪚㪢㪌㪐㪞㪥㪛㪟㫀㪝㫀㪶㪩㪍㪇㪛㫆㫆㪩㪶㪘㪣㪫㪊㪏
㪞㪥㪛㪊㪊㪞㪥㪛㪍㪈㪪㪚㪣㪈㪶㪊㪭㪶㪈㪇㪇㪟㫀㪝㫀㪶㪣㪍㪉㪠㪩㪨㪆㪝㪘㪥㪶㪘㪣㪫㪊㪐
㪍㪊㪪㪛㪘㪈㪶㪊㪭㪶㪈㪇㪇㪞㪥㪛㪍㪋㪧㪛㪮㪥㪋㪇
㪍㪌㪞㪥㪛㪟㪛㪛㪶㪣㪍㪍㪙㪣㪶㪧㪮㪤㪋㪈
㪍㪎㪍㪌㪍㪶㪛㪐㪟㪛㪛㪶㪩㪍㪏
㪍㪐㪍㪌㪍㪶㪛㪏㪞㪥㪛㪎㪇
㪎㪈㪍㪌㪍㪶㪛㪎㪪㪜㪣㪶㪣㪶㪤㪎㪉
㪎㪊㪍㪌㪍㪶㪛㪍㪪㪜㪣㪶㪩㪶㪤㪎㪋
㪎㪌㪍㪌㪍㪶㪛㪌㪞㪥㪛㪎㪍
㪎㪎㪍㪌㪍㪶㪛㪋㪬㪘㪫㪯㪛㪊㪎㪏
㪎㪐㪍㪌㪍㪶㪛㪊㪬㪘㪩㪯㪛㪊㪏㪇
㪏㪈㪍㪌㪍㪶㪛㪉㪞㪥㪛㪏㪉
㪏㪊㪍㪌㪍㪶㪛㪈㪬㪘㪩㪫㪪㪊㪶㪥㪏㪋
㪏㪌㪍㪌㪍㪶㪛㪇㪬㪘㪚㪫㪪㪊㪶㪥㪏㪍
㪏㪎㪞㪥㪛㪤㪛㪤㪶㪛㪚㪛㪶㪥㪏㪏
㪏㪐㪍㪌㪍㫆㪶㪚㪣㪢㪤㪛㪤㪶㪩㪪㪫㪶㪥㪐㪇
㪐㪈㪞㪥㪛㪫㪬㪥㪩㪪㪫㪶㪥㪐㪉
㪐㪊㪍㪌㪍㪶㪟㪛㪩㪜㪪㪜㪫㪉㪶㪥㪐㪋
㪐㪌㪍㪌㪍㪶㪭㪛㪧㫆㪮㪜㪩㪶㪉㪶㪫㪻㪐㪍
㪐㪎㪘㪣㪜㪩㪫㪘㪥㪫㪶㪪㪜㪣㪐㪏
㪐㪐㫀㪩㪙㪶㪩㪪㪫㪶㪥㪞㪥㪛㪈㪇㪇
㪈㪇㪈㫀㪩㪶㪚㪘㪧㫀㪥㪪㪚㪣㪇㪶㪊㪭㪶㪋㪇㪇㪈㪇㪉
㪈㪇㪊㪘㪭㫀㪩㪪㪜㪣㪪㪛㪘㪇㪶㪊㪭㪶㪋㪇㪇㪈㪇㪋
㪈㪇㪌㪧㫆㪮㪜㪩㫆㪝㪝㪞㪥㪛㪈㪇㪍
㪈㪇㪎㪞㪥㪛㪝㪜㪚㪶㪫㪤㪚㪚㪝㪈㪇㪏
㪈㪇㪐㪬㪜㫀㪶㪫㪯㪛㪶㪥㪍㪌㪍㪶㪝㪣㪛㪈㪈㪇
㪈㪈㪈㪬㪜㫀㪶㪩㪯㪛㪶㪥㪪㪫㪬㪥㪩㪜㪨㪇㪈㪈㪉
㪈㪈㪊㪞㪥㪛㪪㪫㪬㪥㪩㪜㪨㪈㪈㪈㪋
㪈㪈㪌㪝㪘㪥㪶㪛㪜㪫㪝㪜㪚㪶㪫㪤㪚㪚㪝㪉㪈㪈㪍
㪪㪠㪛㪜㩷㪫㪜㪩㪤㪠㪥㪘㪣㩷㪈㪈㪎㪤㪧㫆㪜㪈㪈㪏
㪈㪈㪐㪤㪪㪛㪪㪫㪬㪥㪩㪜㪨㪇㪶㪉㪈㪉㪇
㪈㪉㪈㪤㪧㪚㪜㪪㪫㪬㪥㪩㪜㪨㪈㪶㪉㪈㪉㪉
㪧㪝㪪㪧㪫㪝㪈㪉㪊㪤㪪㪫㪞㪥㪛㪈㪉㪋
㪱㪟㪄㪈㪊㪭㪱㪟㪄㪈㪊㪟㪈㪉㪌㪧㪥㪣㫆㪥㪪㪚㪘㪩㪫㪶㪩㪈㪉㪍
㪭㪌㪶㪚㪰㪈㪈㪭㪌㪶㪚㪰㪈㪉㪎㪣㪥㪙㪪㪟㫆㪩㪫㪪㪚㪘㪩㪫㪶㪞㪈㪉㪏
㪞㪥㪛㪉㪉㪞㪥㪛㪈㪉㪐㪘㪬㪛㫀㫆㪶㪤㪬㪫㪜㪪㪚㪘㪩㪫㪶㪙㪈㪊㪇
㪭㪌㪶㪧㪙㪊㪊㪭㪌㪶㪧㪙㪈㪊㪈㪩㪜㪚㪶㪤㪬㪫㪜㪫㪯㪫㪶㪙㪣㪢㪈㪊㪉
㪞㪥㪛㪋㪋㪞㪥㪛㪈㪊㪊㪟㪧㪶㪤㪬㪫㪜㪫㪯㪫㪶㪟㪛㪈㪊㪋
㪭㪌㪶㪧㪩㪌㪌㪭㪌㪶㪧㪩㪈㪊㪌㪟㪧㪶㪪㪜㪣㪫㪯㪫㪶㪭㪛㪈㪊㪍
㪞㪥㪛㪍㪍㪞㪥㪛㪈㪊㪎㪞㪥㪛㪞㪥㪛㪈㪊㪏
㪭㪌㪶㪣㪎㪎㪭㪌㪶㪣㪈㪊㪐㪤㪧㪜㪞㪶㪧㪛㪎㪫㪪㪊㪶㪚㪣㪢㪈㪋㪇
㪭㪌㪶㪩㪏㪏㪭㪌㪶㪩㪈㪋㪈㪤㪧㪜㪞㪶㪧㪛㪍㪞㪥㪛㪈㪋㪉
㪞㪥㪛㪐㪐㪞㪥㪛㪈㪋㪊㪤㪧㪜㪞㪶㪧㪛㪌㪫㪪㪊㪶㪜㪥㪈㪋㪋
㫀㪥㪌㪶㪛㪜㪫㪈㪇㪈㪇㫀㪥㪌㪶㪛㪜㪫㪈㪋㪌㪤㪧㪜㪞㪶㪧㪛㪋㪫㪪㪊㪶㪪㪰㪥㪚㪈㪋㪍
㪞㪥㪛㪈㪈㪈㪈㪞㪥㪛㪈㪋㪎㪤㪧㪜㪞㪶㪧㪛㪊㪫㪪㪊㪶㪛㪇㪈㪋㪏
㪞㪥㪛㪈㪉㪈㪉㪞㪥㪛㪈㪋㪐㪤㪧㪜㪞㪶㪧㪛㪉㪞㪥㪛㪈㪌㪇
㪫㪂㪐㪭㪈㪊㪈㪊㪫㪂㪐㪭㪈㪌㪈㪤㪧㪜㪞㪶㪧㪛㪈㪙㪛㪶㪻㪜㪫㪇㪈㪌㪉
㪈㪌㪊㪤㪧㪜㪞㪶㪧㪛㪇㪙㪛㪶㪻㪜㪫㪈㪈㪌㪋
㪈㪌㪌㪞㪥㪛㪙㪛㪶㪻㪜㪫㪉㪈㪌㪍
㪈㪌㪎㪤㪧㪜㪞㪶㪧㪚㪣㪢㪈㪌㪏
㪈㪌㪐㪞㪥㪛㪪㪮㫀㪭㪜㪣㪶㪘㫉㫀㪈㪍㪇
㪈㪍㪈㪤㪧㪜㪞㪶㪧㪪㪰㪥㪚㪛㪜㪪㪫㪇㪈㪍㪉
㪈㪍㪊㪤㪧㪜㪞㪶㪧㪜㪥㪛㪜㪪㪫㪈㪈㪍㪋
㪈㪍㪌㪞㪥㪛㪞㪥㪛㪈㪍㪍
㪈㪍㪎㪪㪫㪭㪶㪘㪝㪚㪘㪭㪚㪫㪯㪛㪈㪍㪏
㪈㪍㪐㪤㪫㪭㪶㪘㪝㪚㪘㪭㪚㪩㪯㪛㪈㪎㪇
㪈㪎㪈㪘㪭㪚㪚㪫㪪㪶㪥㪈㪎㪉
㪈㪎㪊㪘㪭㪚㪩㪫㪪㪶㪥㪈㪎㪋
㪈㪎㪌㪚㪈㪶㫀㪥㪞㪥㪛㪈㪎㪍
㪈㪎㪎㪪㫀㪞㪶㪛㪜㪫㪚㪩㪯㫀㪥㪈㪎㪏
㪈㪎㪐㪛㪩㪯㫀㪥㪈㪏㪇
㪈㪏㪈㪫㪭㪪㪶㪣㪪㪮㪶㪪㪜㪣㪈㪏㪉
㪈㪏㪊㪞㪥㪛㪛㫀㪧㪶㪛㪜㪫㪈㪏㪋
㪈㪏㪌㪫㪯㪛㪂㪉㪊㪉㪚㪶㪪㪜㪣㪈㪏㪍
㪈㪏㪎㪞㪥㪛㪜㪯㪫㪶㪩㪜㪪㪜㪫㪈㪏㪏
㪈㪏㪐㪫㪯㪛㪄㪛㪫㪫㪶㪧㫆㪮㪜㪩㪈㪐㪇
㪈㪐㪈㪞㪥㪛㪞㪥㪛㪈㪐㪉
㪈㪐㪊㪩㪯㫀㪥㪂㪈㪐㪋
㪈㪐㪌㪞㪥㪛㪈㪐㪍
㪈㪐㪎㪩㪯㫀㪥㪄㪈㪐㪏
㪈㪐㪐㪞㪥㪛㪞㪥㪛㪉㪇㪇
㪧㪦㪛㩷㪧㪮㪙
㪧㪮㪇㪈㪧㪘㪇㪈
㪌㪇㪈㪏㪍㪋㪄㪏㪇㪟㪣㫆㫎㪌㪇㪈㪎㪏㪍㪄㪏㪇㪈㪈
㪛㪂㪊㪅㪊㪭㪏㪇㪈㪛㪂㪊㪅㪊㪭
㪪㪙㪘㪛㪛㪈㪊㪎㪐㪉㪪㪙㪘㪛㪛㪈㪊
㪪㪙㪘㪛㪛㪈㪉㪎㪏㪊㪪㪙㪘㪛㪛㪈㪉
㪪㪙㪘㪛㪛㪈㪈㪎㪎㪋㪪㪙㪘㪛㪛㪈㪈
㪪㪙㪘㪛㪛㪈㪇㪎㪍㪌㪪㪙㪘㪛㪛㪈㪇
㪪㪙㪘㪛㪛㪐㪎㪌㪍㪪㪙㪘㪛㪛㪐
㪞㪥㪛㪎㪋㪎㪧㫆㪛㪶㪘㫉㫀
㪪㪙㪘㪛㪛㪏㪎㪊㪏㪪㪙㪘㪛㪛㪏
㪪㪙㪘㪛㪛㪎㪎㪉㪐㪪㪙㪘㪛㪛㪎
㪪㪙㪘㪛㪛㪍㪎㪈㪈㪇㪪㪙㪘㪛㪛㪍
㪪㪙㪘㪛㪛㪌㪎㪇㪈㪈㪪㪙㪘㪛㪛㪌
㪪㪙㪘㪛㪛㪋㪍㪐㪈㪉㪪㪙㪘㪛㪛㪋
㪪㪙㪘㪛㪛㪊㪍㪏㪈㪊㪪㪙㪘㪛㪛㪊
㪪㪙㪘㪛㪛㪉㪍㪎㪈㪋㪪㪙㪘㪛㪛㪉
㪪㪙㪘㪛㪛㪈㪍㪍㪈㪌㪪㪙㪘㪛㪛㪈
㪞㪥㪛㪍㪌㪈㪍㪞㪥㪛
㪪㪙㪛㪘㪫㪎㪍㪋㪈㪎㪪㪙㪛㪘㪫㪎
㪪㪙㪛㪘㪫㪍㪍㪊㪈㪏㪪㪙㪛㪘㪫㪍
㪪㪙㪛㪘㪫㪌㪍㪉㪈㪐㪪㪙㪛㪘㪫㪌
㪪㪙㪛㪘㪫㪋㪍㪈㪉㪇㪪㪙㪛㪘㪫㪋
㪪㪙㪛㪘㪫㪊㪍㪇㪉㪈㪪㪙㪛㪘㪫㪊
㪪㪙㪛㪘㪫㪉㪌㪐㪉㪉㪪㪙㪛㪘㪫㪉
㪪㪙㪛㪘㪫㪈㪌㪏㪉㪊㪪㪙㪛㪘㪫㪈
㪪㪙㪛㪘㪫㪇㪌㪎㪉㪋㪪㪙㪛㪘㪫㪇
㪪㪙㫆㪜㪶㪥㪌㪍㪉㪌㪪㪙㫆㪜㪈㪈㪶㪥
㪪㪙㪮㪜㪶㪥㪌㪌㪉㪍㪪㪙㪮㪜㪈㪈㪶㪥
㪪㪙㪙㪜㪇㪶㪥㪌㪋㪉㪎㪪㪙㪙㪜㪇㪶㪥
㪪㪙㪘㪚㪢㪶㪥㪌㪊㪉㪏㪪㪙㪘㪚㪢㪶㪥
㪞㪥㪛㪌㪉㪉㪐㪞㪥㪛
㪪㪙㪚㪣㪢㪶㪊㪌㪈㪊㪇㪪㪙㪚㪣㪢㪶㪊
㪩㪜㪪㪜㪫㪈㪶㪥㪌㪇㪊㪈㪩㪜㪪㪜㪫㪈㪶㪥
㪚㫆㪥㪝㪶㪧㪩㫆㪞㪋㪐㪊㪉㪚㫆㪥㪝㪶㪧㪩㫆㪞
㪚㫆㪥㪝㪶㫀㪥㫀㪫㪋㪏㪊㪊㪚㫆㪥㪝㪶㫀㪥㫀㪫
㪚㫆㪥㪝㪶㪛㫆㪥㪜㪋㪎㪊㪋㪚㫆㪥㪝㪶㪛㫆㪥㪜
㪞㪥㪛㪋㪍㪊㪌㪞㪥㪛
㪤㪚㪣㪢㫆㪋㪌㪊㪍㪤㪚㪣㪢㫆
㪞㪥㪛㪋㪋㪊㪎㪞㪥㪛
㪤㪛㫆㪛㪋㪊㪊㪏㪤㪛㫆㪛
㪤㫆㪭㪘㪣㪋㪉㪊㪐㪤㫆㪭㪘㪣
㪤㫆㪪㪫㪩㪫㪋㪈㪋㪇㪤㫆㪪㪫㪩㪫
㪚㪩㪯㫀㪥㪋㪇㪋㪈㪚㪩㪯㫀㪥
㪛㪩㪯㫀㪥㪊㪐㪋㪉㪛㪩㪯㫀㪥
㪞㪥㪛㪊㪏㪋㪊㪞㪥㪛
㪤㪧㪜㪞㪶㪧㪚㪣㪢㪊㪎㪋㪋㪧㫆㪛㪶㪧㪚㪣㪢
㪞㪥㪛㪊㪍㪋㪌㪞㪥㪛
㪤㪧㪜㪞㪶㪧㪛㪎㪊㪌㪋㪍㪤㪧㪜㪞㪶㪧㪛㪎
㪤㪧㪜㪞㪶㪧㪛㪍㪊㪋㪋㪎㪤㪧㪜㪞㪶㪧㪛㪍
㪤㪧㪜㪞㪶㪧㪛㪌㪊㪊㪋㪏㪤㪧㪜㪞㪶㪧㪛㪌
㪤㪧㪜㪞㪶㪧㪛㪋㪊㪉㪋㪐㪤㪧㪜㪞㪶㪧㪛㪋
㪤㪧㪜㪞㪶㪧㪛㪊㪊㪈㪌㪇㪤㪧㪜㪞㪶㪧㪛㪊
㪤㪧㪜㪞㪶㪧㪛㪉㪊㪇㪌㪈㪤㪧㪜㪞㪶㪧㪛㪉
㪤㪧㪜㪞㪶㪧㪛㪈㪉㪐㪌㪉㪤㪧㪜㪞㪶㪧㪛㪈
㪤㪧㪜㪞㪶㪧㪛㪇㪉㪏㪌㪊㪧㫆㪛㪶㪧㪛㪇
㪤㪧㪜㪞㪶㪧㪜㪥㪉㪎㪌㪋㪧㫆㪛㪶㪧㪜㪥
㪤㪧㪜㪞㪶㪧㪪㪰㪥㪚㪉㪍㪌㪌㪧㫆㪛㪶㪧㪪㪰㪥㪚
㪞㪥㪛㪉㪌㪌㪍㪞㪥㪛
㪧㪣㪣㪶㪍㪍㪤㪉㪋㪌㪎㪧㪣㪣㪶㪍㪍㪤
㪞㪥㪛㪉㪊㪌㪏㪞㪥㪛
㪪㪙㪚㪜㪍㪸㪶㪥㪉㪉㪌㪐㪪㪙㪚㪜㪍㪸㪶㪥
㪪㪙㪚㪜㪎㪶㪥㪉㪈㪍㪇㪪㪙㪚㪜㪎㪶㪥
㪧㫆㪛㪶㪚㪛㪶㪥㪉㪇㪍㪈㪧㫆㪛㪶㪚㪛㪶㪥
㫀㪩㪜㪨㪶㪥㪈㪐㪍㪉㫀㪩㪜㪨㪶㪥
㪧㪞㪶㪂㪌㪅㪍㪭㪈㪏㪍㪊㪧㪞㪶㪂㪌㪅㪍㪭
㪧㪥㪣㫆㪥㪈㪎㪍㪋㪧㪥㪣㫆㪥
㪪㪛㪛㪘㪫㪊㪈㪍㪍㪌㪪㪛㪛㪘㪫㪊
㪪㪛㪛㪘㪫㪉㪈㪌㪍㪍㪪㪛㪛㪘㪫㪉
㪪㪛㪛㪘㪫㪈㪈㪋㪍㪎㪪㪛㪛㪘㪫㪈
㪪㪛㪮㪧㪈㪊㪍㪏㪪㪛㪮㪧
㪪㪛㪛㪘㪫㪇㪈㪉㪍㪐㪪㪛㪛㪘㪫㪇
㪪㪛㪚㪛㪈㪈㪎㪇㪪㪛㪚㪛
㪪㪛㪚㪤㪛㪈㪇㪎㪈㪪㪛㪚㪤㪛
㪞㪥㪛㪐㪎㪉㪞㪥㪛
㪪㪛㪚㪣㪢㪏㪎㪊㪪㪛㪚㪣㪢
㪞㪥㪛㪎㪎㪋㪞㪥㪛
㪍㪎㪌
㪂㪌㪅㪍㪭㪌㪎㪍㪂㪌㪅㪍㪭
㪂㪌㪅㪍㪭㪋㪎㪎㪂㪌㪅㪍㪭
㪂㪌㪅㪍㪭㪊㪎㪏㪂㪌㪅㪍㪭
㪂㪌㪅㪍㪭㪉㪎㪐㪂㪌㪅㪍㪭
㪂㪌㪅㪍㪭㪈㪏㪇㪂㪌㪅㪍㪭
㪪㪠㪛㪜㩷㪟㪛㪤㪠㩷㪧㪮㪙
㪧㪟㪇㪈㪧㪋㪇㪊
㪝㪠㪩㪄㪉㪈㪟㪝㪠㪩㪄㪉㪈㪟
㪮㪧㪉㪈㪈㪮㪧
㪟㪧㪛㪉㪇㪉㪟㪧㪛
㪂㪌㪭㪛㪜㪫㪈㪐㪊㪂㪌㪭㪛㪜㪫
㪞㪥㪛㪈㪏㪋㪞㪥㪛
㪪㪛㪘㪈㪎㪌㪪㪛㪘
㪪㪚㪣㪈㪍㪍㪪㪚㪣
㪘㪚㪢㪈㪌㪎㪘㪚㪢
㪪㪰㪥㪚㪂㪌㪭㪈㪋㪏㪪㪰㪥㪚㪂㪌㪭
㪞㪥㪛㪈㪊㪐㪞㪥㪛
㪩㪯㪚㪄㪈㪉㪈㪇㪩㪯㪚㪄
㪩㪯㪚㪂㪈㪈㪈㪈㪩㪯㪚㪂
㪞㪥㪛㪈㪇㪈㪉㪞㪥㪛
㪩㪯㪇㪄㪐㪈㪊㪩㪯㪇㪄
㪩㪯㪇㪂㪏㪈㪋㪩㪯㪇㪂
㪞㪥㪛㪎㪈㪌㪞㪥㪛
㪩㪯㪈㪄㪍㪈㪍㪩㪯㪈㪄
㪩㪯㪈㪂㪌㪈㪎㪩㪯㪈㪂
㪞㪥㪛㪋㪈㪏㪞㪥㪛
㪩㪯㪉㪄㪊㪈㪐㪩㪯㪉㪄
㪩㪯㪉㪂㪉㪉㪇㪩㪯㪉㪂
㪞㪥㪛㪈㪉㪈㪞㪥㪛
㪧㪟㪇㪉㪧㪋㪇㪈
㪝㪠㪩㪄㪉㪈㪟㪌㪇㪈㪊㪊㪈㪄㪇㪉㪭
㪚㪜㪚㪈㪈㪚㪜㪚
㪧㪤㪚
㪌㪇㪈㪌㪎㪈㪄㪋㪇㪟
㪈㪪㪛㪛㪘㪫㪊㪶㪞㪥㪛㪉
㪊㪞㪥㪛㪪㪛㪛㪘㪫㪇㪶㪋
㪌㪪㪛㪚㪤㪛㪶㪞㪥㪛㪍
㪎㪞㪥㪛㪪㪛㪚㪣㪢㪶㫆㪬㪫㪏
㪐㪪㪛㪛㪘㪫㪈㪶㪞㪥㪛㪈㪇
㪈㪈㪪㪛㪛㪘㪫㪉㪶㪪㪛㪚㪛㪶㪈㪉
㪈㪊㪪㪛㪮㪧㪶㪧㫆㪮㪜㪩㪶㪉㪶㪫㪻㪈㪋
㪈㪌㪂㪌㪅㪍㪭㪛㪂㪊㪅㪊㪭㪈㪍
㪈㪎㪪㪙㪰㪂㪌㪅㪇㪭㪚㪘㪩㪛㪶㫀㪥㪈㪏
㪈㪐㪙㫀㪚㪚㪣㪢㪚㪥㪞㪪㪚㪇㪭㪚㪚㪜㪥㪶㪥㪉㪇
㪉㪈㪝㪩㪜㪪㪜㪫㪶㪥㪪㪚㪇㪚㪎㫀㫆㪉㪉
㪉㪊㪪㪚㪇㪩㪪㪫㪪㪚㪇㪛㪜㪫㪶㪥㪉㪋
㪉㪌㪞㪥㪛㪧㪮㪩㪢㪜㪰㪉㪍
㪉㪎㪘㪛㪢㪜㪰㪇㪘㪛㪢㪜㪰㪈㪉㪏
㪉㪐㪙㪘㪚㪢㪶㪩㪪㪫㪞㪣㪜㪛㪶㪣㪘㪤㪧㪊㪇
㪊㪈㪩㪶㪣㪜㪛㪧㪮㪜㪩㪣㪜㪛㪈㪊㪉㪪㪧㪄㪙㫆㫋㫋㫆㫄㩷㩿㪣㪀
㪊㪊㪧㪮㪜㪩㪣㪜㪛㪇㪘㪣㪘㪩㪤㪣㪜㪛㪇㪊㪋
㪊㪌㪂㪌㪅㪍㪭㪞㪥㪛㪊㪍
㪊㪎㪪㪙㪰㪂㪌㪅㪇㪭㫀㪩㪶㪚㪘㪧㫀㪥㪊㪏
㪚㪦㪥㪫㪩㪦㪣㩷㪧㪮㪙㪊㪐㫀㪩㪶㫀㪥㪪㪙㪰㪂㪊㪅㪊㪭㪋㪇㪈䋫
㪉㪥㪚
㪊䋭
㪧㪚㪤㪉
㪧㪟㪄㪇㪌㪟㪄㪛
㪞㪥㪛㪈
㪧㪮㪩㪢㪜㪰㪉㪪㪧㪄㪪㫀㪻㪼㩷㩿㪣㪀
㪘㪛㪢㪜㪰㪇㪊
㪘㪛㪢㪜㪰㪈㪋㪧㪪㪧㪢
㪞㪥㪛㪌㪧㪘㪄㪇㪏㪟
㪈䋫
㪮㫆㪑㪣㫆㫌㫋㪄㪧㪈㪉䋭
㪮㫆㪑㪣㫆㫌㫋㪄㪥㪉
㪪㫀㪻㪼㪑㪣㫆㫌㫋㪄㪧㪊
㪪㫀㪻㪼㪑㪣㫆㫌㫋㪄㪥㪋
㪮㫆㪑㪩㫆㫌㫋㪄㪧㪌
㪮㫆㪑㪩㫆㫌㫋㪄㪥㪍㪪㪧㪄㪙㫆㫋㫋㫆㫄㩷㩿㪩㪀
㪣㪜㪛㩷㪧㪮㪙㪪㫀㪻㪼㪑㪩㫆㫌㫋㪄㪧㪎
㪪㫀㪻㪼㪑㪩㫆㫌㫋㪄㪥㪏
㪧㪚㪤㪈㪈䋫
㪌㪇㪈㪊㪊㪈㪄㪈㪈㪭㪉㪥㪚
㪞㪶㪣㪜㪛㪈㪊䋭
㪩㪶㪣㪜㪛㪉
㪧㪮㪩㪣㪜㪛㪈㪊
㪧㪮㪩㪣㪜㪛㪇㪋
㪘㪣㪘㪩㪤㪣㪜㪛㪇㪌㪪㪧㪄㪪㫀㪻㪼㩷㩿㪩㪀
㪪㪫㪙㪰㪂㪌㪅㪇㪭㪍
㪪㫀㪞㪂㪌㪅㪍㪭㪎
㪞㪥㪛㪏
㫀㪩㪶㪚㪘㪧㫀㪥㪐㪈䋫
㪪㪫㪙㪰㪂㪊㪅㪊㪭㪈㪇㪉䋭
㫀㪩㪶㫀㪥㪈㪈
58
TABLE OF CONTENTS
DW2U
FINAL WIRING DIAGRAM
TABLE OF CONTENTS 59
DW2U
QUICK DISASSEMBLE GUIDE (Back Cover 1)
① Remove Screw M3M 6*18 P#MJ03963(2 Pcs.)

Cable Clamp M6 P#ML02111(2 Pcs.)
② Remove Screw M3M 6*25 P#MJ03973(2 Pcs.)
③ Remove Screw M3D 4*10 P#MJ03973
④ Remove Screw M3M 6*25 P#MJ03973(2 Pcs.)
STAND METAL SUPPORT
DW2U
QUICK DISASSEMBLE GUIDE (Back Cover 2)
⑤ Remove Screw M3D 4*10 P#MJ03973(22 Pcs.)
BACK COVER
61
DW2U
QUICK DISASSEMBLE GUIDE (Fans)
① Remove Screw M3E 4*10 P#MJ04039(4 Pcs.)
② Remove Screw M3E 3*8 P#MJ03963(4 Pcs.)
③ Remove Fans(R,L) P#GS00702(2 Pcs.)
FAN SUPPORT METAL
FAN ASSY (L)
FAN ASSY (R)
FAN SUPPORT METAL 2
62
DW2U
QUICK DISASSEMBLE GUIDE (Power Unit)

④ Remove Screw M3E 3*8 P#MJ03963(2 Pcs.)
Screw M3M 3*8 P#MJ03598(4 Pcs.)
⑤ Remove Power Unit P#HA01731
TO RELEASE POWER UNIT FROM THE PANEL IT IS NECESSARY

TO PRESS 3 HOLDERS IN 3 POSITIONS.
63
DW2U
QUICK DISASSEMBLE GUIDE (Chassis Block)
① Remove Screw M3E 4*10 P#MJ04039(2 Pcs.)
CHASSIS BLOCK
64
DW2U
QUICK DISASSEMBLE GUIDE (Terminal Metal)
② Remove Screw M3E 3*8 P#MJ03963(4 Pcs.)
③ Remove Screw D-Sub P#MJ03351(2 Pcs.)
④ Remove Tuner Nut Washer P#MK01432
⑤ Remove Screw T2B 3*10 P#MJ03733(4 Pcs.)
⑥ Remove Screw M3E 3*8 P#MJ03963(4 Pcs.)
⑦ Remove Screw M3M 3*6 P#MJ03594(4 Pcs.)
65
DW2U
QUICK DISASSEMBLE GUIDE (POD PWB)

① Remove Screw M3E 3*8 P#MJ03963
② Remove POD PWB Assy 42HDS69 P#JP50341

42HDT79 P#JP05342
42HDX99 P#JP05432
66
DW2U
QUICK DISASSEMBLE GUIDE (Main / Sub Digital PWB)
③ Remove Main Digital PWB Assy
④ Remove Sub Digital PWB Assy
See page 115 for part numbers
IS NECESSARY TO RELEASE MAIN PWB AND

SUB PWB FROM BOARD HOLDERS(3 POSITIONS)
CH 4
67
FINAL ASSEMBLY GUIDE DW2U
69
70
71
72
73
74
75
76
77
DW2U
WAVEFORMS
Numbers inside circle correspond to locations shown in the circuit diagram. Waveforms taken
using a Color Bar signal with H sync 31 khz and V. sync 60 hz and a X10 probe.
Signal amplitude and DC level shown at ∆ and @ respectively.
1 IT02 Pin 41 MPEG-DATA 0 2 IT02 Pin 42 MPEG-DATA 1 3 IT02 Pin 47 MPEG-DATA 2
4.0 V 4.0 V 4.0 V
4 IT02 Pin 48 MPEG-DATA 3 5 IT02 Pin 50 MPEG-DATA 4 6 IT02 Pin 51 MPEG-CLK
4.0 V 4.0 V
7 IT02 Pin 54 MPEG-DATA 5 8

5 IT02 Pin 57 MPEG-DATA 6 9 IT02 Pin 59 MPEG-DATA 7/SER_DATA
4.0 V 4.0 V 4.0 V
10 IT02 Pin 63 MPEG_DATA EN 11 IT02 Pin 66 MPEG_PKT_SYNC
4.0 V
SUBDIGITAL PWB
QAM/VSB DEMODULATOR
click here to go to circuit diagram
78
TABLE OF CONTENTS
DW2U
WAVEFORMS
Numbers inside circle correspond to locations shown in the circuit diagram. Waveforms taken
using a Color Bar signal with H sync 31 khz and V. sync 60 hz and a X10 probe.
Signal amplitude and DC level shown at ∆ and @ respectively.
12 I001 Pin 44 DATA 13 I001 Pin 45 CLK 14 I001 Pin 30 PR OUT 1
15 I001 Pin 29 PB OUT 1 16 I001 Pin 28 Y OUT 17 I001 Pin 32 SUB/Y/V OUT
SUBDIGITAL PWB
I001 AV SWITCH
click here to go to circuit diagram
79
DW2U
DC VOLTAGES
(42" Models only)
Symbol Pin No. Voltage Symbol Pin No. Voltage Symbol Pin No. Voltage
CN63 1 5.2 CNPPS 1 5.8 PCM1 1 0
2 0 2 5.8 2 4.3
3 3.3 3 5.8 3 0
4 0 4 0 4 4
5 3.8 5 0 5 5
6 4.8 6 0 6 5
7 3.1 7 10.8 7 5.8
8 3.3 8 0 8 0
9 16.3 9 0
Symbol Pin No. Voltage 10 0 10 3.3
CN64 1 63.4 11 0 11 0
2 NC 12 0
3 5.1 13 10.8 Symbol Pin No. Voltage
4 0 14 10.8 PCM2 1 0
5 0 15 10.8 2 5
6 0 3 5
7 N.C Symbol Pin No. Voltage 4 5
8 83.5 PTF 1 0 5 0
9 83.5 2 0
10 83.5 3 0 Symbol Pin No. Voltage
4 0 PSPK 1 5.3
Symbol Pin No. Voltage 5 0 2 5.3
CN68 1 5.1 6 0 3 5.5
2 0 7 2.1 4 5.5
3 3.3 8 2.1 5 5.3
4 0 9 0 6 5.3
5 1.6 10 0 7 5.4
6 1.3 11 0 8 5.4
7 2.6 12 0
8 2.6 13 9 Symbol Pin No. Voltage
9 3.3 PFA2 1 6
Symbol Pin No. Voltage 2 0
Symbol Pin No. Voltage PFA1 1 6 3 0
P401 1 0 2 0
2 0 3 0
TABLE OF CONTENTS
80
DW2U
DC VOLTAGES
(42" Models only)
Symbol Pin No. Voltage Symbol Pin No. Voltage Symbol Pin No. Voltage
IT05 1 3.3 IW03 1 1.2 IW04 1 3.3
2 0 2 0 2 0
3 1.3 3 0 3 1.2
4 5 4 0.3 4 2.5
5 5.8 5 2.5 5 3.3
6 0
Symbol Pin No. Voltage 7 0 Symbol Pin No. Voltage
IT11 1 4 8 2.5 UT01 1 0
2 0 2 5
3 1.3 Symbol Pin No. Voltage 3 0
4 1.8 IWP2 1 3.3 4 1.7
5 3.3 2 0 5 2.3
3 1.2 6 0
Symbol Pin No. Voltage 4 3.3 7 5
IT12 1 2 5 5.8 8 1.9
2 0 9 4.8
3 1.3 Symbol Pin No. Voltage 10 4.8
4 3.3 IWP1 1 2.3 11 2.8
5 5.8 2 5.8 12 1.9
3 5.8 13 2.2
Symbol Pin No. Voltage 4 0 14 0
IW02 1 0 5 0.5 15 2.2
2 5.8 6 0 16 2.2
3 0 7 3.3 17 0
4 0 8 3.3 18 5
5 0.15 9 0 19 0
10 0 20 5
81
DW2U
BASIC CIRCUIT DIAGRAM Subdigital 1 of 6
PRODUCT SAFETY NOTE: Components marked with a ! and shaded have special characteristics
important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY
NOTE of this Service Manual. Don't degrade the safety of the receiver through improper servicing.
1 2 3 4 5 6
11
7 10
2 3 4 5 8
1
6
• All DC voltage to be measured with a tester (100 kΩ/V). Voltage taken on a complex color bar including a standard color bar signal. TUNER/DEMOD
• Since this is a basic circuit diagram, the value of the parts is subject to be altered for improvement.
TABLE OF CONTENTS
82
DW2U
1 2 3 4 5 6
13
12
17
14
15
16
• All DC voltage to be measured with a tester (100 kΩ/V). Voltage taken on a complex color bar including a standard color bar signal. AV-SWITCH
83
DW2U
1 2 3 4 5 6
• All DC voltage to be measured with a tester (100 kΩ/V). Voltage taken on a complex color bar including a standard color bar signal. TERMINAL
84
DW2U
1 2 3 4 5 6
• All DC voltage to be measured with a tester (100 kΩ/V). Voltage taken on a complex color bar including a standard color bar signal.
200 pin I/F
85
DW2U
1 2 3 4 5 6
POWER SWIVEL
86
DW2U
1 2 3 4 5 6
UEI/IR BLASTER
87
DW2U
BASIC CIRCUIT DIAGRAM POD 1 of 1
1 2 3 4 5 6
POD
88
DW2U
BASIC CIRCUIT DIAGRAM Front HDMI 1 of 1
1 2 3 4 5 6
FRONT HDMI
89
DW2U
BASIC CIRCUIT DIAGRAM LED 1 of 1
1 2 3 4 5 6
LED
90
DW2U
BASIC CIRCUIT DIAGRAM OPT 1 of 1
1 2 3 4 5 6
OPT
91
DW2U
BASIC CIRCUIT DIAGRAM FILTER 1 of 1
1 2 3 4 5 6
FILTER
92
DW2U
BASIC CIRCUIT DIAGRAM SIDE TERMINAL 1 of 1
1 2 3 4 5 6
SIDE TERMINAL
93
DW2U
BASIC CIRCUIT DIAGRAM CONTROL 1 of 1
1 2 3 4 5 6
CONTROL
94
PRINTED CIRCUIT BOARDS DW2-U
DW2-U SUBDIGITAL PWB (Component side)
SEMICONDUCTOR LOCATION
(Component side)
1 2 3 4 5
QT03 B-5
IC
QT04 B-5
I004 B-2 QT05 B-5
I005 B-2 QT06 C-3
IL01 B-2 QT07 C-3
IM05 D-3 QY01 B-3
IP03 D-5 QY02 B-3
IP05 B-1 QY03 B-3
A IPT1
IT02
D-2
C-4
DIODE
IT03 A-5
IT04 C-4 D001 B-3
IT05 A-5 D006 B-3
IT07 A-3 DL01 D-5
IT09 C-5 DL02 D-5
IT10 B-3 DL03 D-5
IT11 C-3 DL04 D-5
IT12 C-4 DM01 D-4
IY01 A-3 DM02 C-4
IY02 A-3 DP01 C-5
IY03 B-3 DP02 C-5
B TRANSISTOR
DP10
DP12
B-1
C-5
DPT1 D-2
Q001 A-2 DY01 A-3
Q002 A-2 DY02 A-3
Q007 B-2 DY03 A-3
Q008 B-2
Q009 B-2
CRYSTAL & FILTER
Q010 B-2
Q011 C-3 XM02 C-3
Q012 A-2 XPT1 D-3
Q014 A-2 XT01 C-5
Q016 B-2 XT02 B-5
QL01 B-2 XT03 B-4
C QM02
QP04
D-2
B-1
XT04
XT09
C-4
B-5
QP06 C-1
BACK TO TABLE OF CONTENTS

95
DW2-U SUBDIGITAL PWB (Solder side)
SEMICONDUCTOR LOCATION
(Solder side)
1 2 3 4 5
IC
I001 B-4
IM01 D-4
IM02 C-4
IM03 C-4
A IM04 D-3
IM06 C-3
IM07 C-4
IM08 C-4
IT06 B-2
IT08 A-2
TRANSISTOR
Q013 C-4
B Q015 C-4
QM01 D-4
QM03 C-4
QM04 C-3
QP05 B-5
QPS1 B-2
QT01 C-2
QT02 C-2
DIODE
C DP09 B-5
DPS1 B-2
DPS2 B-2
DT02 A-1
DT03 C-2
DT04 D-2
CRYSTAL & FILTER

XM01 D-4
D XT06 B-1
XT07 B-1
XT08 B-1
XT10 A-1
XT11 C-2
96
DW2-U POD PWB (Component side)
SEMICONDUCTOR LIST
(Component side)
IC
IW02
IW03
IW04
IWP1
IWP2
DIODE
DW01
DW02
CRYSTAL & FILTER

XWP1
97
DW2-U POD PWB (Solder side)
SEMICONDUCTOR LIST
(Solder side)
IC
IW01
IWE1
IWE2
TRANSISTOR
QW01
QWE1
98
DW2-U FRONT HDMI PWB
(Component side) (Solder side) SEMICONDUCTOR LIST
Component side
IC
IH02
Solder side
IC
IH01
IH03
IH04
IH05
DIODE
DH01
DH02
TRANSISTOR
QH01
QH02
QH03
QH04
99
DW2-U LED PWB
SEMICONDUCTOR LIST
(Component side)
Component side
IC
IN01
IN02
(Solder side)
Solder side
DIODE
DN01
DN02
HN01
HN02
100
DW2-U OPT PWB
(Component side)
(Solder side)
101
DW2-U FILTER PWB
(Component side) (Solder side)
Component side
FILTER
X9A1
X9A2
102
DW2-U SIDE TERMINAL PWB
(Component side)
(Solder side)
Component side
TRANSISTOR
QNJ1
QNJ2
103
DW2-U CONTROL PWB
(Component side)
(Solder side)
104
DW2U
REPLACEMENT PARTS LIST

PRODUCT SERVICE NOTE: Components marked with a ! have special characteristics important to safety. Before replacing any
of these components, read carefully, the PRODUCT SAFETY NOTICE of this Service Manual. Don’t degrade the safety of the
receiver through improper servicing.
ABBREVIATIONS
Capacitors: Resistors: Semiconductors:
AL: Aluminum Electrolytic CF: Carbon Film TR: Transistor
CD: Ceramic Disc CC: Carbon Composition DI: Diode
EL: Electrolitic MF: Metal Oxide ZD: Zener Diode
PF: Polyester Film VR: Variable Resistor VA: Varistor
PP: Polypropylene WW: Wire Wound TH: Termistor
PL: Plastic FR: Fuse Resistor IC: Integrated Circuit
TA: Tantalum MG: Metal Grazed
PR: Paper
TM: Trimmer
MC: Mylar
42HDX99
42HDT79
42HDS69
42HDS69
42HDT79
42HDX99
SYMBOL PART No. DESCRIPTION SYMBOL PART No. DESCRIPTION

C040 AA01123R CCC105K10-B-16CT 0 0 0
SUBDIGITAL PWB C041 AA01123R CCC105K10-B-16CT 0 0 0
JP50321 0 C042 AA01123R CCC105K10-B-16CT 0 0 0
JP50322 0 C043 AA01123R CCC105K10-B-16CT 0 0 0
JP50323 0 C044 AA01123R CCC105K10-B-16CT 0 0 0
CAPACITORS C045 AA01123R CCC105K10-B-16CT 0 0 0
C001 AA01136R CERAMIC CAPACITOR(0.47UF 6.3V) 0 0 0 C046 AA01123R CCC105K10-B-16CT 0 0 0
C002 AA01343R CERAMIC CAPACITOR(0.047UF 25V- 0 0 0 C047 AA01123R CCC105K10-B-16CT 0 0 0
C005 AA01115R CAP.CHIP1608-B-4.7UF6.3V 0 0 0 C060 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 0
C006 AA01116R CAP.CHIP1608-B-10UF 6.3V M 0 0 0 C061 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 0
C007 AA01343R CERAMIC CAPACITOR(0.047UF 25V- 0 0 0 C062 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 0
C008 AA01136R CERAMIC CAPACITOR(0.47UF 6.3V) 0 0 0 C063 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 0
C009 AA01136R CERAMIC CAPACITOR(0.47UF 6.3V) 0 0 0 C078 AA01144R CERAMIC CAP. 1608-B 1.0UF 16V 0 0 0
C012 AA01116R CAP.CHIP1608-B-10UF 6.3V M 0 0 0 C079 0893126R CAP 1608CHIP 100PFJCH 50V TAPE 0 0 0
C014 AA01123R CCC105K10-B-16CT 0 0 0 C080 0893208R CAP 1608CHIP 1000PFKB 50V TAPE 0 0 0
C015 AA01136R CERAMIC CAPACITOR(0.47UF 6.3V) 0 0 0 C081 AA01144R CERAMIC CAP. 1608-B 1.0UF 16V 0 0 0
C016 AA01123R CCC105K10-B-16CT 0 0 0 C082 AA01185R CAP.CHIP-CERAMIC 22UF/16V B 32 0 0 0
C017 AA01123R CCC105K10-B-16CT 0 0 0 C083 AA01141R CERAMIC CAPACITOR(0.1UF 16V) 0 0 0
C018 0893188R CERAMIC CAPACITOR(47000PF 16V) 0 0 0 C084 AA01144R CERAMIC CAP. 1608-B 1.0UF 16V 0 0 0
C019 AA01136R CERAMIC CAPACITOR(0.47UF 6.3V) 0 0 0 C085 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
C020 AA01343R CERAMIC CAPACITOR(0.047UF 25V- 0 0 0 C086 AA01144R CERAMIC CAP. 1608-B 1.0UF 16V 0 0 0
C021 AA01136R CERAMIC CAPACITOR(0.47UF 6.3V) 0 0 0 C087 AA01141R CERAMIC CAPACITOR(0.1UF 16V) 0 0 0
C022 0893188R CERAMIC CAPACITOR(47000PF 16V) 0 0 0 C088 AA00969R CAP.CHIP2125-B-22UF6.3V 0 0 0
C028 AA01136R CERAMIC CAPACITOR(0.47UF 6.3V) 0 0 0 C094 AA00968R CCC106M06-B-20CT (10UF 6.3V 2012M) 0 0 0
C030 AA01123R CCC105K10-B-16CT 0 0 0 C097 AA01141R CERAMIC CAPACITOR(0.1UF 16V) 0 0 0
C031 AA01123R CCC105K10-B-16CT 0 0 0 C0A1 AA00969R CAP.CHIP2125-B-22UF6.3V 0 0 0
C032 AA01123R CCC105K10-B-16CT 0 0 0 C0A2 AA01141R CERAMIC CAPACITOR(0.1UF 16V) 0 0 0
C033 AA01123R CCC105K10-B-16CT 0 0 0 C0A3 AA00969R CAP.CHIP2125-B-22UF6.3V 0 0 0
C039 AA01123R CCC105K10-B-16CT 0 0 0 C0K0 AA01136R CERAMIC CAPACITOR(0.47UF 6.3V) 0 0 0

DW2U
42HDS69
42HDX99
42HDS69
42HDX99
42HDT79
42HDT79
SYMBOL PART # DESCRIPTION SYMBOL PART # DESCRIPTION
C0K1 AA01136R CERAMIC CAPACITOR(0.47UF 6.3V) 0 0 0 CT03 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CH01 0893333R CAP.CHIP-CERAMIC 10000PF 16V TAPE 0 0 0 CT12 0893222R CAP 1608CHIP10000PFKB 50V TAPE 0 0 0
CH02 CE00151R EZJZ0V80010 0 0 0 CT15 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CH13 AA01231R 0.1UF 16V 1005-B CERAMIC CAPAC 0 0 0 CT24 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CH14 AA01116R CAP.CHIP1608-B-10UF 6.3V M 0 0 0 CT25 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CH20 0893333R CAP.CHIP-CERAMIC 10000PF 16V TAPE 0 0 0 CT31 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CH27 AA01216R CAP.CHIP-CERAMIC 1005B 1UF 6.3 0 0 0 CT38 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CH28 AA01216R CAP.CHIP-CERAMIC 1005B 1UF 6.3 0 0 0 CT39 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CL01 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 CT42 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CL13 AA01347R CERAMIC CAPACITOR(0.1UF 25V-B) 0 0 0 CT45 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CM01 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 CT49 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CM02 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 CT50 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CM03 AA00968R CCC106M06-B-20CT (10UF 6.3V 2012M) 0 0 CT51 AA01111R CERAMIC CAPACITOR(1.0UF 6.3V) 0 0 0
CM06 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 CT52 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CM07 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 CT53 AA01111R CERAMIC CAPACITOR(1.0UF 6.3V) 0 0 0
CM08 AA00955R CAP.CHIP-CERAMIC 2125 B 4.7UF 0 0 CT54 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CM09 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 CT55 AA01111R CERAMIC CAPACITOR(1.0UF 6.3V) 0 0 0
CM10 0893199R CAP 1608CHIP 220PFKB 50V TAPE 0 0 CT56 AA01111R CERAMIC CAPACITOR(1.0UF 6.3V) 0 0 0
CM11 0893199R CAP 1608CHIP 220PFKB 50V TAPE 0 0 CT57 AA01111R CERAMIC CAPACITOR(1.0UF 6.3V) 0 0 0
CM12 AA01812R CCC153K50-B-16CT 0 0 CT58 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CM13 AA01812R CCC153K50-B-16CT 0 0 CT59 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CM14 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 CT60 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 0
CM15 0893222R CAP 1608CHIP10000PFKB 50V TAPE 0 0 0 CT61 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CM16 AA01123R CCC105K10-B-16CT 0 0 0 CT62 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CM17 AA01123R CCC105K10-B-16CT 0 0 0 CT63 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 0
CP07 AA01144R CERAMIC CAP. 1608-B 1.0UF 16V 0 0 0 CT64 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CP13 AA01144R CERAMIC CAP. 1608-B 1.0UF 16V 0 0 0 CT65 AA01144R CERAMIC CAP. 1608-B 1.0UF 16V 0 0 0
CP14 0893222R CAP 1608CHIP10000PFKB 50V TAPE 0 0 0 CT66 AA01111R CERAMIC CAPACITOR(1.0UF 6.3V) 0 0 0
CP18 AA01185R CAP.CHIP-CERAMIC 22UF/16V B 32 0 0 CT67 AA01144R CERAMIC CAP. 1608-B 1.0UF 16V 0 0 0
CP19 AA01185R CAP.CHIP-CERAMIC 22UF/16V B 32 0 0 CT68 AA01111R CERAMIC CAPACITOR(1.0UF 6.3V) 0 0 0
CP20 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 CT69 AA01173R CCC1R0K50-B-32CT 1UF/50V-B-3225 0 0 0
CP21 AA00699R CAP.CHIP-CERAMIC 10UFK 16V B 3 0 0 CT71 AA01144R CERAMIC CAP. 1608-B 1.0UF 16V 0 0 0
CP22 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 CT72 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 0
CP23 0893193R CAP 1608CHIP 10000PFKB 25V TAPE 0 0 CT73 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 0
CP24 0893193R CAP 1608CHIP 10000PFKB 25V TAPE 0 0 CT74 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CPS1 AA01123R CCC105K10-B-16CT 0 0 0 CT75 AA01802R CCC103K50-B-16CT MCH18 0 0 0
CPS2 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 CT76 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 0
CPS3 0893211R CAP 1608CHIP 1500PFKB 50V TAPE 0 0 0 CT77 0893208R CAP 1608CHIP 1000PFKB 50V TAPE 0 0 0
CPS4 0893127R CAP 1608CHIP 120PFJCH 50V TAPE 0 0 0 CT78 0893222R CAP 1608CHIP10000PFKB 50V TAPE 0 0 0
CPS5 0893193R CAP 1608CHIP 10000PFKB 25V TAPE 0 0 0 CT79 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CPS6 0893127R CAP 1608CHIP 120PFJCH 50V TAPE 0 0 0 CT80 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 0
CPS7 0893222R CAP 1608CHIP10000PFKB 50V TAPE 0 0 0 CT81 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 0
CPT2 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 0 CT83 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CPT3 AA00969R CAP.CHIP2125-B-22UF6.3V 0 0 0 CT84 0893208R CAP 1608CHIP 1000PFKB 50V TAPE 0 0 0
CPT5 0893222R CAP 1608CHIP10000PFKB 50V TAPE 0 0 0 CT85 AA01111R CERAMIC CAPACITOR(1.0UF 6.3V) 0 0 0
CPT7 0893215R CAP 1608CHIP 3300PFKB 50V TAPE 0 0 0 CT86 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 0
CPT8 0893188R CERAMIC CAPACITOR(47000PF 16V) 0 0 0 CT89 0893123R CAP 1608CHIP 56PFJCH 50V TAPE 0 0 0
106
DW2U
42HDS69
42HDX99
42HDS69
42HDX99
42HDT79
42HDT79
CT90 0893124R CAP 1608CHIP 68PFJCH 50V TAPE 0 0 0 CY10 AD00633R CEC471M16-EWMT 105 0 0 0
CT91 0893115R CAP 1608CHIP 15PFJCH 50V TAPE 0 0 0 CY11 AA01144R CERAMIC CAP. 1608-B 1.0UF 16V 0 0 0
CT92 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 CY12 AA01144R CERAMIC CAP. 1608-B 1.0UF 16V 0 0 0
CT93 0893222R CAP 1608CHIP10000PFKB 50V TAPE 0 0 0 CY13 AA01123R CCC105K10-B-16CT 0 0 0
CT95 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 CY14 AA01123R CCC105K10-B-16CT 0 0 0
CT96 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 CY15 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CT97 0893222R CAP 1608CHIP10000PFKB 50V TAPE 0 0 0 CY16 AA00966R CERAMIC CAPACITOR(4.7UF 6.3V) 0 0 0
CTA1 0893222R CAP 1608CHIP10000PFKB 50V TAPE 0 0 0
CTA3 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 0 DIODES
CTC1 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 D001 CC01921R SDS142WKF_PF 0 0 0
CTC2 0893222R CAP 1608CHIP10000PFKB 50V TAPE 0 0 0 DH02 CC01891R SDS511_PF 0 0 0
CTC3 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 DM01 CC01891R SDS511_PF 0 0
CTC4 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 DM02 CC01891R SDS511_PF 0 0
CTC5 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 DP01 CC01891R SDS511_PF 0 0 0
CTC6 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 DP02 CC01891R SDS511_PF 0 0 0
CTC8 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 DP10 CC02075R ZENER.CHIP EDZ TE61 5.1B 0 0
CTC9 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 DPS1 CC02022R ZENER.CHIP UDZSTE-1730B 0 0 0
CTE1 AA00968R CCC106M06-B-20CT (10UF 6.3V 2012M) 0 0 0 DPS2 CC01891R SDS511_PF 0 0 0
CTE2 AA00968R CCC106M06-B-20CT (10UF 6.3V 2012M) 0 0 0 DPT1 CC02211R RSX201L-30 0 0 0
CTE3 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 DT02 CC01131R ZENER.CHIP MAZS3000H 0 0 0
CTE4 AA01144R CERAMIC CAP. 1608-B 1.0UF 16V 0 0 0 DY01 CC01999R ZENER.CHIP UDZSTE-174.3B 0 0
CTE5 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 DY02 CC01999R ZENER.CHIP UDZSTE-174.3B 0 0
CTF2 0893222R CAP 1608CHIP10000PFKB 50V TAPE 0 0 0
CTF3 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 INTEGRATED CIRCUITS (IC's)
CTF4 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 I001 CK53531U R2S11008FP 0 0 0
CTF6 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 I004 CK51331R TK11100CS 0 0 0
CTF7 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 I005 CK37218R MONO IC TK11150CSCL 0 0 0
CTF8 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 0 IH02 CK53891R TMDS SW IC CXB1441R 0 0 0
CTF9 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 IH03 CK37216R MONO IC TK11133CSCL 0 0 0
CTG1 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 IH04 CK38329R DIGITAL MONOLITHIC IC (SN74LVC 0 0 0
CTG2 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 0 IH05 CK38329R DIGITAL MONOLITHIC IC (SN74LVC 0 0 0
CTG3 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 IL01 CK50961R SN74CB3T3306DCUR 0 0 0
CTG4 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 IM01 CK51632R 9DR32DW8-1046 0 0
CTG5 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 0 IM02 CK51091R SN74LVC1G3157DCKR 0 0
CTG6 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 IM03 CK38328R IC SN74LVC1G125DCKR 0
CTG9 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 IM04 CK38328R IC SN74LVC1G125DCKR 0 0
CTH1 AA01111R CERAMIC CAPACITOR(1.0UF 6.3V) 0 0 0 IM05 2015203R HD74HC00TELLE 0 0
CTH2 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 IM06 CK54692R GENERAL LOGIC IV(TC74AC163FT) 0 0
CTH6 0893222R CAP 1608CHIP10000PFKB 50V TAPE 0 0 0 IM07 CK51091R SN74LVC1G3157DCKR 0 0
CTH7 0893222R CAP 1608CHIP10000PFKB 50V TAPE 0 0 0 IM08 CK37218R MONO IC TK11150CSCL 0 0 0
CTJ4 0893125R CAP 1608CHIP 82PFJCH 50V TAPE 0 0 0 IP03 CK52481R TK73400TCB-G 0 0 0
CTJ5 0893119R CAP 1608CHIP 33PFJCH 50V TAPE 0 0 0 IP05 CK50461R ANALOG MONOLITHIC IC(BA6287F- 0 0
CTJ6 0893106R CAP 1608CHIP 4PFCCK 50V TAPE 0 0 0 IPT1 CK54161R ANALOG MONOLITHIC IC(MP2361DK 0 0 0
CTJ7 0893124R CAP 1608CHIP 68PFJCH 50V TAPE 0 0 0 IT02 CK54051U THEATER314 0 0 0
CTJ8 AA00968R CCC106M06-B-20CT (10UF 6.3V 2012M) 0 0 0 IT03 CK51091R SN74LVC1G3157DCKR 0 0 0
CTK3 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 IT04 CK50961R SN74CB3T3306DCUR 0 0 0
CTK4 0893113R CAP 1608CHIP 10PFCCH 50V TAPE 0 0 0 IT05 CK37218R MONO IC TK11150CSCL 0 0 0
CTK5 0893113R CAP 1608CHIP 10PFCCH 50V TAPE 0 0 0 IT06 CK37605R IC TK11250CM 0 0 0
CTK6 AA01144R CERAMIC CAP. 1608-B 1.0UF 16V 0 0 0 IT07 CK37605R IC TK11250CM 0 0 0
CTK7 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 IT09 CK51151R UPC3221GV 0 0 0
CTK8 AA00968R CCC106M06-B-20CT (10UF 6.3V 2012M) 0 0 0 IT10 CK51141R UPC3220GR 0 0 0
CTK9 0893208R CAP 1608CHIP 1000PFKB 50V TAPE 0 0 0 IT11 CK37211R MONO IC TK11118CSCL 0 0 0
CTM1 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 IT12 CK37216R MONO IC TK11133CSCL 0 0 0
CTM2 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 IY01 CK38325R DIGITAL MONOLITHIC IC (SN74LVC 0 0
CTM3 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 IY02 CK38325R DIGITAL MONOLITHIC IC (SN74LVC 0 0
CTM4 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 IY03 CK50027R DIGITAL MONOLITHIC IC (MAX202I 0 0 0
CTM5 AA01144R CERAMIC CAP. 1608-B 1.0UF 16V 0 0 0
CTM6 AA01144R CERAMIC CAP. 1608-B 1.0UF 16V 0 0 0 COILS
CTM7 0893222R CAP 1608CHIP10000PFKB 50V TAPE 0 0 0 L001 BA00887R LBC2518 CHIP COIL 10UH 0 0 0
CTM8 0893222R CAP 1608CHIP10000PFKB 50V TAPE 0 0 0 L002 BA00887R LBC2518 CHIP COIL 10UH 0 0 0
CTM9 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 0 L005 BA00887R LBC2518 CHIP COIL 10UH 0 0 0
CTN1 AA01111R CERAMIC CAPACITOR(1.0UF 6.3V) 0 0 0 L006 BA00887R LBC2518 CHIP COIL 10UH 0 0 0
CTN4 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 LM01 BA00894R LBC2518 CHIP COIL 100UH 0 0
CTN5 0893222R CAP 1608CHIP10000PFKB 50V TAPE 0 0 0 LM02 BA00894R LBC2518 CHIP COIL 100UH 0
CY01 AA01185R CAP.CHIP-CERAMIC 22UF/16V B 32 0 0 LM03 BA00894R LBC2518 CHIP COIL 100UH 0 0
CY02 0893126R CAP 1608CHIP 100PFJCH 50V TAPE 0 0 LP04 BA01164R GLC2518 CHIP INDUCTOR 10UH 0 0 0
CY03 0893126R CAP 1608CHIP 100PFJCH 50V TAPE 0 0 LPS1 BA02185R HCC221J2520CT 0 0 0
CY04 0893126R CAP 1608CHIP 100PFJCH 50V TAPE 0 0 LPS2 BA02244R HCC102J32CT 0 0 0
CY05 0893126R CAP 1608CHIP 100PFJCH 50V TAPE 0 0 LPT1 BA02251R 7E06NG TYPE POWER INDUCTOR 4.7 0 0 0
CY06 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 LT10 BM10348R CHIP FERRITE BEAD BLM18PG121SN 0 0 0
CY07 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 LT11 BM10348R CHIP FERRITE BEAD BLM18PG121SN 0 0 0
CY08 0893222R CAP 1608CHIP10000PFKB 50V TAPE 0 0 0 LT12 BM10348R CHIP FERRITE BEAD BLM18PG121SN 0 0 0
CY09 AD00633R CEC471M16-EWMT 105 0 0 0 LT13 BM10348R CHIP FERRITE BEAD BLM18PG121SN 0 0 0
107
DW2U
42HDS69
42HDX99
42HDS69
42HDX99
42HDT79
42HDT79
LT16 BM00151R FILTER BLM21P300SPT 0 0 0 R028 AQ00421R CHIP RESISTOR 1608(2)0OHM 0 0 0
LT17 BA00161R COIL HCC47NK16CT-HK1608 0 0 0 R029 AQ00457R RES.-CHIP 1/16W 1.0K-J (2 UNIT) 0 0 0
LT18 BA01227R HK2125 TYPE CHIP INDUCTOR 150N 0 0 0 R032 0790024R RES.CHIP 1/16W 100 OHM 0 0 0
LT19 BA00162R CHIP COIL 56NK16CT-HK1608 0 0 0 R033 0790024R RES.CHIP 1/16W 100 OHM 0 0 0
LT20 BA01127R MLF2012 CHIP INDUCTOR 1.8UH 0 0 0 R034 0790024R RES.CHIP 1/16W 100 OHM 0 0 0
LT25 BA00189R CHIP COIL 33NJ16CT-HK1608 0 0 0 R035 0790024R RES.CHIP 1/16W 100 OHM 0 0 0
LT28 BA00191R COIL HCC39NJ16CT-HK1608 0 0 0 R038 0790024R RES.CHIP 1/16W 100 OHM 0 0 0
LT29 BA01127R MLF2012 CHIP INDUCTOR 1.8UH 0 0 0 R039 AQ00439R CHIP RESISTOR 47 1608 0 0 0
LT30 BM10348R CHIP FERRITE BEAD BLM18PG121SN 0 0 0 R040 AQ00439R CHIP RESISTOR 47 1608 0 0 0
LT34 BM10348R CHIP FERRITE BEAD BLM18PG121SN 0 0 0 R045 AQ00164R CHIP RESITOR 1/16W 75OHM TAPE 0 0 0
LY01 BA00894R LBC2518 CHIP COIL 100UH 0 0 0 R049 AQ00164R CHIP RESITOR 1/16W 75OHM TAPE 0 0 0
R050 AQ00164R CHIP RESITOR 1/16W 75OHM TAPE 0 0 0
TRANSISTORS R069 AQ00519R CHIP RESISTOR 47OHM 0 0 0
Q001 CA02162R SUT487J 0 0 0 R070 AQ00519R CHIP RESISTOR 47OHM 0 0 0
Q002 CA02162R SUT487J 0 0 0 R071 AQ00439R CHIP RESISTOR 47 1608 0 0 0
Q007 1323294R TRS.CHIP 2SA1774 TL (R/S) 0 0 0 R072 AQ00484R RES.-CHIP 1/16W 100K-J (2 UNIT 0 0 0
Q011 CA01181R D-TRS.CHIP IMD10A 0 0 0 R076 AQ00484R RES.-CHIP 1/16W 100K-J (2 UNIT 0 0 0
Q012 CA00461R TRS.CHIP 2SD2114K 20V TAPE 0 0 0 R082 AQ00457R RES.-CHIP 1/16W 1.0K-J (2 UNIT) 0 0 0
Q013 CA14091R PHOTO TRANSISTOR 0 0 0 R083 AQ00457R RES.-CHIP 1/16W 1.0K-J (2 UNIT) 0 0 0
Q014 CA00461R TRS.CHIP 2SD2114K 20V TAPE 0 0 0 R088 AQ00544R CHIP RESISTOR 3.3KOHM 0 0 0
Q015 CA02162R SUT487J 0 0 0 R096 0790015R RES.CHIP 1/16W 22 OHM 0 0 0
Q016 1323294R TRS.CHIP 2SA1774 TL (R/S) 0 0 0 R099 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0
QH01 1323293R TRS.CHIP 2SC4617 TL (R/S) 0 0 0 R0A0 0790015R RES.CHIP 1/16W 22 OHM 0 0 0
QL01 CA02091R SRC1204EF_PF 0 0 0 R0A3 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0
QM01 CA02091R SRC1204EF_PF 0 0 R0A4 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0
QM02 CA02142R TRS.CHIP 2SC5343UFG_PF 0 0 R0A5 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0
QM03 CA02091R SRC1204EF_PF 0 0 R0A6 0790015R RES.CHIP 1/16W 22 OHM 0 0 0
QM04 1323294R TRS.CHIP 2SA1774 TL (R/S) 0 0 R0A7 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0
QP04 1323294R TRS.CHIP 2SA1774 TL (R/S) 0 0 R0C3 AQ00448R CHIP RESISTOR 220 1608 0 0 0
QP05 CA14091R PHOTO TRANSISTOR 0 0 R0C4 AQ00483R CHIP RESISTOR 82K 1608 0 0 0
QP06 CA02091R SRC1204EF_PF 0 0 R0C9 AQ00457R RES.-CHIP 1/16W 1.0K-J (2 UNIT) 0 0 0
QPS1 CA14091R PHOTO TRANSISTOR 0 0 0 R0E1 AQ00471R RES.-CHIP 1/16W 10K-J (2 UNIT) 0 0 0
QT01 CA14091R PHOTO TRANSISTOR 0 0 0 R0E2 0790051R RES.CHIP 1/16W 10K OHM 0 0 0
QT02 CA14091R PHOTO TRANSISTOR 0 0 0 R0G4 AQ00266R RES.CHIP 1/16W 510K OHM TAPE 0 0 0
QT03 CA02171R TRS.CHIP 2SC4082T106P 0 0 0 R0G5 AQ00245R RES.CHIP 1/16W 82K OHM TAPE 0 0 0
QT04 CA02171R TRS.CHIP 2SC4082T106P 0 0 0 R0G7 0790059R RES.CHIP 1/16W 47K OHM 0 0 0
QT05 CA02171R TRS.CHIP 2SC4082T106P 0 0 0 R0G8 0790059R RES.CHIP 1/16W 47K OHM 0 0 0
QT06 CA14091R PHOTO TRANSISTOR 0 0 0 R0G9 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0
QT07 CA14091R PHOTO TRANSISTOR 0 0 0 R0H0 0790051R RES.CHIP 1/16W 10K OHM 0 0 0
QY01 CA11641R PHOTO TRANSISTOR 0 0 R0H1 0790064R RES.CHIP 1/16W 100K OHM 0 0 0
QY02 CA11641R PHOTO TRANSISTOR 0 0 R0H2 0790064R RES.CHIP 1/16W 100K OHM 0 0 0
QY03 1323294R TRS.CHIP 2SA1774 TL (R/S) 0 0 R0H3 0790064R RES.CHIP 1/16W 100K OHM 0 0 0
R0H4 0790064R RES.CHIP 1/16W 100K OHM 0 0 0
RESISTORS R0H5 0790051R RES.CHIP 1/16W 10K OHM 0 0 0
R001 AQ00164R CHIP RESITOR 1/16W 75OHM TAPE 0 0 0 R0H6 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
R002 AQ00164R CHIP RESITOR 1/16W 75OHM TAPE 0 0 0 R0H7 0790051R RES.CHIP 1/16W 10K OHM 0 0 0
R005 AQ00164R CHIP RESITOR 1/16W 75OHM TAPE 0 0 0 R0J2 0790073R RES.CHIP 1/16W 470K OHM 0 0 0
R006 0790024R RES.CHIP 1/16W 100 OHM 0 0 0 R0K0 0790024R RES.CHIP 1/16W 100 OHM 0 0 0
R007 0790024R RES.CHIP 1/16W 100 OHM 0 0 0 R0K1 AQ00164R CHIP RESITOR 1/16W 75OHM TAPE 0 0 0
R011 AQ00457R RES.-CHIP 1/16W 1.0K-J (2 UNIT) 0 0 0 R0K4 0790024R RES.CHIP 1/16W 100 OHM 0 0 0
R014 0790024R RES.CHIP 1/16W 100 OHM 0 0 0 R0K7 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0
R019 0790024R RES.CHIP 1/16W 100 OHM 0 0 0 RH01 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
R020 AQ00164R CHIP RESITOR 1/16W 75OHM TAPE 0 0 0 RH02 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
R024 0790051R RES.CHIP 1/16W 10K OHM 0 0 0 RH03 0790024R RES.CHIP 1/16W 100 OHM 0 0 0
R025 0790051R RES.CHIP 1/16W 10K OHM 0 0 0 RH04 0790024R RES.CHIP 1/16W 100 OHM 0 0 0
R026 0790024R RES.CHIP 1/16W 100 OHM 0 0 0 RH05 0790024R RES.CHIP 1/16W 100 OHM 0 0 0
R027 0790024R RES.CHIP 1/16W 100 OHM 0 0 0 RH06 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
108
DW2U
42HDS69
42HDX99
42HDS69
42HDX99
42HDT79
42HDT79
RH07 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 RM23 0790051R RES.CHIP 1/16W 10K OHM 0 0
RH10 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 RM27 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RH12 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 RM29 0790077R RES.CHIP 1/16W 1.0M OHM 0 0
RH13 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 RM30 0790044R RES.CHIP 1/16W 3.3K OHM 0 0
RH14 0790064R RES.CHIP 1/16W 100K OHM 0 0 0 RM31 0790037R RES.CHIP 1/16W 1.0K OHM 0 0
RH15 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 RM32 0790051R RES.CHIP 1/16W 10K OHM 0
RH17 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0 RP03 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RH18 0790024R RES.CHIP 1/16W 100 OHM 0 0 0 RP06 0790051R RES.CHIP 1/16W 10K OHM 0 0 0
RH19 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0 RP07 0790051R RES.CHIP 1/16W 10K OHM 0 0 0
RH20 0790051R RES.CHIP 1/16W 10K OHM 0 0 0 RP12 0790024R RES.CHIP 1/16W 100 OHM 0 0 0
RH22 0790059R RES.CHIP 1/16W 47K OHM 0 0 0 RP18 0790073R RES.CHIP 1/16W 470K OHM 0 0 0
RH23 0790059R RES.CHIP 1/16W 47K OHM 0 0 0 RP19 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RH24 0790046R RES.CHIP 1/16W 4.7K OHM 0 0 0 RP29 0196116R RES.-1608CHIP 1/16W 91K-J TAPE 0 0 0
RH25 0790046R RES.CHIP 1/16W 4.7K OHM 0 0 0 RP30 0790055R RES.CHIP 1/16W 22K OHM 0 0 0
RH26 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 RP45 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0
RH28 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 RP46 0790024R RES.CHIP 1/16W 100 OHM 0 0
RH29 AQ00212R RES.CHIP 1/16W 4.7K OHM TAPE 0 0 0 RP47 0790024R RES.CHIP 1/16W 100 OHM 0 0
RH30 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 RP49 AQ01954R RES.CHIP RK73B3ATTE 5R6J 0 0
RH31 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 RP50 0790051R RES.CHIP 1/16W 10K OHM 0 0
RH32 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 RP51 AQ01938R RES.CHIP RK73B3ATTE 1R5J 0 0
RH33 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 RP52 0790037R RES.CHIP 1/16W 1.0K OHM 0 0
RH34 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 RP53 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0
RH35 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 RP53 0790077R RES.CHIP 1/16W 1.0M OHM 0 0
RH36 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 RP55 0790024R RES.CHIP 1/16W 100 OHM 0 0
RH37 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 RP56 0790051R RES.CHIP 1/16W 10K OHM 0 0
RH38 0790024R RES.CHIP 1/16W 100 OHM 0 0 0 RP57 0790051R RES.CHIP 1/16W 10K OHM 0 0
RH39 0790024R RES.CHIP 1/16W 100 OHM 0 0 0 RP58 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0
RH40 0790024R RES.CHIP 1/16W 100 OHM 0 0 0 RP60 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0
RH41 0790024R RES.CHIP 1/16W 100 OHM 0 0 0 RP61 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0
RH43 0790051R RES.CHIP 1/16W 10K OHM 0 0 0 RP62 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0
RH44 0790051R RES.CHIP 1/16W 10K OHM 0 0 0 RP63 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0
RL01 0790046R RES.CHIP 1/16W 4.7K OHM 0 0 0 RP64 0790051R RES.CHIP 1/16W 10K OHM 0
RL02 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 RP65 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0
RL03 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 RPG1 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RL04 AQ00471R RES.-CHIP 1/16W 10K-J (2 UNIT) 0 0 0 RPG2 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RL05 AQ00421R CHIP RESISTOR 1608(2)0OHM 0 0 0 RPG3 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RL11 AQ00439R CHIP RESISTOR 47 1608 0 0 0 RPG4 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RL12 AQ00439R CHIP RESISTOR 47 1608 0 0 0 RPS1 0790024R RES.CHIP 1/16W 100 OHM 0 0 0
RL21 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 RPS2 0790059R RES.CHIP 1/16W 47K OHM 0 0 0
RL22 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 RPS3 0790055R RES.CHIP 1/16W 22K OHM 0 0 0
RL23 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 RPT1 AQ00194R RES.CHIP 1/16W 1.0K OHM TAPE 0 0 0
RL24 AQ00439R CHIP RESISTOR 47 1608 0 0 0 RPT2 AQ00221R RES.CHIP 1/16W 10K OHM TAPE 0 0 0
RL25 AQ00439R CHIP RESISTOR 47 1608 0 0 0 RPT3 AQ00212R RES.CHIP 1/16W 4.7K OHM TAPE 0 0 0
RL26 AQ00421R CHIP RESISTOR 1608(2)0OHM 0 0 0 RPT4 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0
RL27 AQ00551R CHIP RESISTOR 10KOHM 0 0 0 RPT6 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RL28 0790051R RES.CHIP 1/16W 10K OHM 0 0 0 RPT7 AQ00178R RES.CHIP 1/16W 270 OHM TAPE 0 0 0
RL41 AQ00551R CHIP RESISTOR 10KOHM 0 0 0 RT01 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RL43 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 RT02 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RL44 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 RT03 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RL51 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 RT04 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RL52 AQ00551R CHIP RESISTOR 10KOHM 0 0 0 RT05 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0
RM01 0790024R RES.CHIP 1/16W 100 OHM 0 0 RT08 0790032R RES.CHIP 1/16W 390 OHM 0 0 0
RM02 0790024R RES.CHIP 1/16W 100 OHM 0 0 RT11 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RM03 0790024R RES.CHIP 1/16W 100 OHM 0 0 RT12 0790019R RES.CHIP 1/16W 47 OHM 0 0 0
RM05 0790051R RES.CHIP 1/16W 10K OHM 0 0 RT13 0790019R RES.CHIP 1/16W 47 OHM 0 0 0
RM06 0790037R RES.CHIP 1/16W 1.0K OHM 0 RT14 0790051R RES.CHIP 1/16W 10K OHM 0 0 0
RM07 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 RT15 0790051R RES.CHIP 1/16W 10K OHM 0 0 0
RM08 0790024R RES.CHIP 1/16W 100 OHM 0 0 RT16 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0
RM09 0790024R RES.CHIP 1/16W 100 OHM 0 0 RT17 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0
RM10 0790047R RES.CHIP 1/16W 5.6K OHM 0 0 RT18 0790006R RES.CHIP 1/16W 4.7 OHM 0 0 0
RM11 0790051R RES.CHIP 1/16W 10K OHM 0 0 RT19 0790006R RES.CHIP 1/16W 4.7 OHM 0 0 0
RM12 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 RT22 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0
RM13 0790077R RES.CHIP 1/16W 1.0M OHM 0 0 RT23 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0
RM14 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 RT24 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0
RM15 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 RT25 0790051R RES.CHIP 1/16W 10K OHM 0 0 0
RM16 0790047R RES.CHIP 1/16W 5.6K OHM 0 0 RT31 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RM17 0790019R RES.CHIP 1/16W 47 OHM 0 0 RT32 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RM18 0790047R RES.CHIP 1/16W 5.6K OHM 0 0 RT33 0790051R RES.CHIP 1/16W 10K OHM 0 0 0
RM19 0790061R RES.CHIP 1/16W 56K OHM 0 0 RT34 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0
RM20 0790062R RES.CHIP 1/16W 68K OHM 0 0 RT35 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0
RM21 0790041R RES.CHIP 1/16W 1.8K OHM 0 0 RT36 AQ00431R CHIP RESISTOR 10 OHM 1608 0 0 0
RM22 0790051R RES.CHIP 1/16W 10K OHM 0 0 RT37 0196881R RES 2125CHIP 1/10W 510-F TAPE 0 0 0
109
DW2U
42HDS69
42HDX99
42HDS69
42HDX99
42HDT79
42HDT79
RT38 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 RY34 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RT39 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 RY35 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RT40 0790052R RES.CHIP 1/16W 12K OHM 0 0 0 RY36 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RT41 0790052R RES.CHIP 1/16W 12K OHM 0 0 0 RY37 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0
RT43 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 RY38 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0
RT44 AQ00164R CHIP RESITOR 1/16W 75OHM TAPE 0 0 0 RY39 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0
RT45 0790043R RES.CHIP 1/16W 2.7K OHM 0 0 0 RY40 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0
RT46 AQ00258R RES.CHIP 1/16W 270K OHM TAPE 0 0 0 RY41 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0
RT52 0790046R RES.CHIP 1/16W 4.7K OHM 0 0 0 RY46 0790056R RES.CHIP 1/16W 27K OHM 0 0
RT53 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RT55 0790052R RES.CHIP 1/16W 12K OHM 0 0 0 CRYSTALS, FILTERS
RT56 AQ00212R RES.CHIP 1/16W 4.7K OHM TAPE 0 0 0 XM01 BL01182R CSTCE16M0V53-R0 0 0
RT57 AQ00244R RES.CHIP 1/16W 75K OHM TAPE 0 0 0 XM02 BP01231 OSX-OSBLA455KEC8-B0 0 0
RT58 0790046R RES.CHIP 1/16W 4.7K OHM 0 0 0 XPT1 BK10324R CERAMIC FILTER NFM2012P13C105BT1 0 0 0
RT59 0790046R RES.CHIP 1/16W 4.7K OHM 0 0 0 XT01 BG01624U SAW FILTER(X6875D) 0 0 0
RT60 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 XT02 BN00261 BGS TRAP MKTGA47M2CAHP00B05 0 0 0
RT61 0790024R RES.CHIP 1/16W 100 OHM 0 0 0 XT03 BG01625U SAW FILTER(X6888D) 0 0 0
RT62 0790024R RES.CHIP 1/16W 100 OHM 0 0 0 XT04 BL01491R OSC25R14X10T 0 0 0
RT63 0790011R RES.CHIP 1/16W 10 OHM 0 0 0 XT06 BK00199R CERAMIC FILTER 2012TYPE 0 0 0
RT64 0790011R RES.CHIP 1/16W 10 OHM 0 0 0 XT07 BK00199R CERAMIC FILTER 2012TYPE 0 0 0
RT65 0790011R RES.CHIP 1/16W 10 OHM 0 0 0 XT08 BK10324R CERAMIC FILTER NFM2012P13C105BT1 0 0 0
RT66 AQ00511R CHIP RESISTOR 10OHM 0 0 0 XT09 BK10324R CERAMIC FILTER NFM2012P13C105BT1 0 0 0
RT67 AQ00511R CHIP RESISTOR 10OHM 0 0 0 XT10 BK10324R CERAMIC FILTER NFM2012P13C105BT1 0 0 0
RT74 0790043R RES.CHIP 1/16W 2.7K OHM 0 0 0 XT11 BK10324R CERAMIC FILTER NFM2012P13C105BT1 0 0 0
RT75 0790043R RES.CHIP 1/16W 2.7K OHM 0 0 0
RT76 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 CONNECTORS, JACKS
RT77 0790051R RES.CHIP 1/16W 10K OHM 0 0 0 JH01 EA02291U HDMI RECEPTACLE DC1R019HBA 0 0 0
RT78 0790051R RES.CHIP 1/16W 10K OHM 0 0 0 JY01 EQ00722 JACK YKC51-0002V 10P(2*5) 0 0 0
RT79 0790051R RES.CHIP 1/16W 10K OHM 0 0 0 JY02 EQ00733 JACK YKC52-0002V(3S+10P) 0 0 0
RT80 0790024R RES.CHIP 1/16W 100 OHM 0 0 0 JY03 EQ00741 JACK 0 0
RT81 0790024R RES.CHIP 1/16W 100 OHM 0 0 0 JY04 EQ00741 JACK 0 0
RT82 0790032R RES.CHIP 1/16W 390 OHM 0 0 0 JY05 EQ00771 JACK 0 0 0
RT83 0790052R RES.CHIP 1/16W 12K OHM 0 0 0 PFA1 EA02192R 3P SMT ZH CONN. POST SIDE 0 0 0
RT84 0790064R RES.CHIP 1/16W 100K OHM 0 0 0 PFA2 EA02192R 3P SMT ZH CONN. POST SIDE 0 0 0
RT85 0790037R RES.CHIP 1/16W 1.0K OHM 0 0 0 PH01 EA02651R PLUG 0 0 0
RT86 0790028R RES.CHIP 1/16W 220 OHM 0 0 0 PH02 EA02341R 2P 1.0MM PITCH CONNE. -501568- 0 0 0
RT87 0790051R RES.CHIP 1/16W 10K OHM 0 0 0 PSM EA02222U 0.5 PITCH 200P B TO B CONN. SH 0 0 0
RT88 0790041R RES.CHIP 1/16W 1.8K OHM 0 0 0 PTF EA02203R 13P SMT ZH CONN. POST SIDE 0 0 0
RT89 0790042R RES.CHIP 1/16W 2.2K OHM 0 0 0 PTW ED01075 PLUG 0 0 0
RT90 0790042R RES.CHIP 1/16W 2.2K OHM 0 0 0
RT98 0790055R RES.CHIP 1/16W 22K OHM 0 0 0 MISCELLANEOUS
RY01 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 UT01 HC00701 ENGD6305 0 0 0
RY02 0790059R RES.CHIP 1/16W 47K OHM 0 0 #TG1 MF02032 GASKET 5-2-15 J1G 0 0 0
RY03 0790064R RES.CHIP 1/16W 100K OHM 0 0 #TG2 MF02033 GASKET 5-2-45 J1G 0 0 0
RY04 0790012R RES.CHIP 1/16W 12 OHM 0 0
RY05 0790012R RES.CHIP 1/16W 12 OHM 0 0 FILTER PWB
RY06 0790012R RES.CHIP 1/16W 12 OHM 0 0 JP50331 0 0 0
RY07 0790012R RES.CHIP 1/16W 12 OHM 0 0
RY09 0790024R RES.CHIP 1/16W 100 OHM 0 0 CAPACITORS
RY10 0790031R RES.CHIP 1/16W 330 OHM 0 0 C9A1B ! AN02089S PLASTIC FILM CAP.CQ-105K251PVS 0 0 0
RY11 AQ00523R CHIP RESISTOR 82OHM 0 0 C9A2A ! AN02087S PLASTIC FILM CAP.CQ-474K251PVS 0 0 0
RY12 AQ00528R CHIP RESISTOR 220OHM 0 0 C9A3 ! AJ00163R CAP. CERAMIC CS11-E2GA222MYVS 0 0 0
RY13 0790031R RES.CHIP 1/16W 330 OHM 0 0 C9A4 ! AJ00163R CAP. CERAMIC CS11-E2GA222MYVS 0 0 0
RY14 AQ00523R CHIP RESISTOR 82OHM 0 0 CNJ1 0800317R CAP.-ELECTRO. 47UF-M(SMG) 16V 0 0 0
RY15 AQ00528R CHIP RESISTOR 220OHM 0 0 CNJ2 0800317R CAP.-ELECTRO. 47UF-M(SMG) 16V 0 0 0
RY16 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 CNJ3 0800291R CAP.-ELECTRO. 10UF-M(SMG) 16V 0 0 0
RY17 0790028R RES.CHIP 1/16W 220 OHM 0 0 CNJ4 0800291R CAP.-ELECTRO. 10UF-M(SMG) 16V 0 0 0
RY18 0790028R RES.CHIP 1/16W 220 OHM 0 0
RY19 0790028R RES.CHIP 1/16W 220 OHM 0 0 JUMPERS
RY20 0790028R RES.CHIP 1/16W 220 OHM 0 0 K9A5 2784381M 0.60MM TAPED JUMP.WIRE 0 0 0
RY21 AQ00163R RES.CHIP 1/16W 68 OHM TAPE 0 0 0 K9A6 2784381M 0.60MM TAPED JUMP.WIRE 0 0 0
RY22 AQ00163R RES.CHIP 1/16W 68 OHM TAPE 0 0 0 K9A7 2784381M 0.60MM TAPED JUMP.WIRE 0 0 0
RY23 AQ00163R RES.CHIP 1/16W 68 OHM TAPE 0 0 0 KL9A2 2784381M 0.60MM TAPED JUMP.WIRE 0 0 0
RY24 0790064R RES.CHIP 1/16W 100K OHM 0 0 0 KNJ1 2784381M 0.60MM TAPED JUMP.WIRE 0 0 0
RY25 0790064R RES.CHIP 1/16W 100K OHM 0 0 0 KNJ2 2784381M 0.60MM TAPED JUMP.WIRE 0 0 0
RY26 0790064R RES.CHIP 1/16W 100K OHM 0 0 0
RY27 0790064R RES.CHIP 1/16W 100K OHM 0 0 0 PROTECTORS, FUSES
RY28 0790064R RES.CHIP 1/16W 100K OHM 0 0 0 F9A2 ! FN00475 FUSE 51MS 063 L-U 6.3A 0 0 0
RY29 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 NF9A2 ! 2721351 FUSE HOLDER 0 0 0
RY31 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RY33 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
110
DW2U
42HDS69
42HDX99
42HDS69
42HDX99
42HDT79
42HDT79
COILS CW12 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
L9A1 ! BZ06251 LINE FILTER TF2722H-A152Y8R0-0 0 0 0 CW13 0893193R CAP 1608CHIP 10000PFKB 25V TAPE 0 0 0
LNJ1 BH00693R COIL 47UH 0 0 0 CW14 AA01115R CAP.CHIP1608-B-4.7UF6.3V 0 0 0
CW15 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
TRANSISTORS CW16 AA01115R CAP.CHIP1608-B-4.7UF6.3V 0 0 0
QNJ1 CF02981R 2SC5343YT_PF 0 0 0 CW17 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
QNJ2 CF02981R 2SC5343YT_PF 0 0 0 CW18 0893193R CAP 1608CHIP 10000PFKB 25V TAPE 0 0 0
CW19 AA01115R CAP.CHIP1608-B-4.7UF6.3V 0 0 0
RESISTORS CW20 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
R9A1 ! AT03661M RES.MTL GRAZD FLM 1/2W 470K 0 0 0 CW21 AA01115R CAP.CHIP1608-B-4.7UF6.3V 0 0 0
RNC1 0700054M RES.-CARBON FLM 1/16W 10K-JB 0 0 0 CW22 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
RNC2 0700049M RES.-CARBON FLM 1/16W 4.7K-JB 0 0 0 CW23 0893193R CAP 1608CHIP 10000PFKB 25V TAPE 0 0 0
RNC3 0700046M RES.-CARBON FLM 1/16W 2.7K-JB 0 0 0 CW24 AA01115R CAP.CHIP1608-B-4.7UF6.3V 0 0 0
RNC4 0700043M RES.-CARBON FLM 1/16W 1.5K-JB 0 0 0 CW25 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
RNC5 0700041M RES.-CARBON FLM 1/16W 1.0K-JB 0 0 0 CW26 0893193R CAP 1608CHIP 10000PFKB 25V TAPE 0 0 0
RNJ1 0700047M RES.-CARBON FLM 1/16W 3.3K-JB 0 0 0 CW27 AA01111R CERAMIC CAPACITOR(1.0UF 6.3V) 0 0 0
RNJ2 0700045M RES.-CARBON FLM 1/16W 2.2K-JB 0 0 0 CW28 AA01113R CCC225K06-B-16CT 0 0 0
RNJ3 0700041M RES.-CARBON FLM 1/16W 1.0K-JB 0 0 0 CW29 0893193R CAP 1608CHIP 10000PFKB 25V TAPE 0 0 0
RNJ4 0700041M RES.-CARBON FLM 1/16W 1.0K-JB 0 0 0 CWE1 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
RNJ9 0700064M RES.-CARBON FLM 1/16W 56K-JB 0 0 0 CWE5 0893208R CAP 1608CHIP 1000PFKB 50V TAPE 0 0 0
RNK1 0700064M RES.-CARBON FLM 1/16W 56K-JB 0 0 0 CWE6 0893208R CAP 1608CHIP 1000PFKB 50V TAPE 0 0 0
RNK2 0100123M RES.-CARBON FLM 1/8W 270K-JB 0 0 0 CWP1 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 0
RNK3 0100123M RES.-CARBON FLM 1/8W 270K-JB 0 0 0 CWP2 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 0
CWP3 AA00969R CAP.CHIP2125-B-22UF6.3V 0 0 0
SWITCHES CWP4 AA00969R CAP.CHIP2125-B-22UF6.3V 0 0 0
S9A0 ! FG00251 POWER SW SPW02N02SY17-2-1(U1D1 0 0 0 CWP5 0893118R CAP 1608CHIP 27PFJCH 50V TAPE 0 0 0
SNC1 FE00551R TACT SWITCH SKHVBDD010 0 0 0 CWP6 0893128R CAP 1608CHIP 150PFJCH 50V TAPE 0 0 0
SNC2 FE00551R TACT SWITCH SKHVBDD010 0 0 0 CWP7 AA01144R CERAMIC CAP. 1608-B 1.0UF 16V 0 0 0
SNC3 FE00551R TACT SWITCH SKHVBDD010 0 0 0 CWP8 AA01144R CERAMIC CAP. 1608-B 1.0UF 16V 0 0 0
SNC4 FE00551R TACT SWITCH SKHVBDD010 0 0 0 CWP9 0893208R CAP 1608CHIP 1000PFKB 50V TAPE 0 0 0
SNC5 FE00551R TACT SWITCH SKHVBDD010 0 0 0
SNC6 FE00551R TACT SWITCH SKHVBDD010 0 0 0 DIODES
SNC7 FE00551R TACT SWITCH SKHVBDD010 0 0 0 DN01 CC02061R LIGHT EMITTING DIODE SML-020ML 0 0 0
DN02 CC01862R SML011BBTT86 0 0 0
CONNECTORS, JACKS DW01 CC00651R SML-210MT T86 GREEN 0 0 0
EP01 EF22542 FASTON CONNECTOR L=110MM LOCK 0 0 0 DW02 CC00652R SML-210DT 0 0 0
J9A1 ! 2676371 PLUG-AC INLET SK-1019 0 0 0
JNJ1 EQ00872 PLUG LPR8029-04**F 0 0 0 MODULES
JNJ2 EQ00871 PLUG LPR8029-05**F 0 0 0 HN01 CE00121R SBX3050-02 0 0 0
PCM2 2675284 PIN POST (PH 5P) 0 0 0 HN02 CZ01261R IRDA MODULE IC (RPM871-H12) 0 0
PFS 2959063 CONNECTOR POST PIN 13P 0 0 0 HNM1 CZ01241 GP1FM514TZ0F 0 0 0
PPU1 ED02812 6P VH CONNECTOR PLUG #2,4,5 NC 0 0 0
INTEGRATED CIRCUITS (IC's)
MISCELLANEOUS IN01 CK38324R DIGITAL MONOLITHIC IC (SN74LVC 0 0 0
#01 NA56414 AC INLET MTL AVC5 0 0 0 IN02 CK38325R DIGITAL MONOLITHIC IC (SN74LVC 0 0
#02 MJ03651 SCRW T3E_3*12BD+SM SWCH16A 0 0 0 IW01 CK53731U XC3S50-5PQG208C 0 0 0
#03 NA82611 DW2 INLET MTL 0 0 0 IW02 CK38378R DIGITAL MONO IC SI-3012KM 0 0 0
#04 MJ04025 SCRW M3S_3*12PN+LSK 0 0 0 IW03 CK51732R MM1701CHBE 0 0 0
#05 MD09981 DW2 INLET WASHER 0 0 0 IW04 CK37212R MONO IC TK11125CSCL 0 0 0
#06 ML02721 MINI CARD SPACER 06 0 0 0 IWE1 CK53741R TC7MBL3245AFK 0 0 0
#07 MK01502 LKW_4.3_8.5 0 0 0 IWE2 CK52581R ANALOG MONOLITHIC IC(MAX4790E 0 0 0
IWP1 CK50071R TPS62040DGQR 0 0 0
IWP2 CK37216R MONO IC TK11133CSCL 0 0 0
POD PWB
JP50341 0 COILS
JP50342 0 0 LN30 BA00892R LBC2518 CHIP COIL 47UH 0 0 0
CAPACITORS LN31 BA00892R LBC2518 CHIP COIL 47UH 0 0
CN30 AA01123R CCC105K10-B-16CT 0 0 0 LWP1 BA02252R 7E06NG TYPE POWER INDUCTOR 6.8 0 0 0
CN31 AA01123R CCC105K10-B-16CT 0 0
CN32 AA01123R CCC105K10-B-16CT 0 0 0 TRANSISTORS
CN33 AA01123R CCC105K10-B-16CT 0 0 QW01 CA02171R TRS.CHIP 2SC4082T106P 0 0 0
CNM1 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 QWE1 CA02091R SRC1204EF_PF 0 0 0
CW01 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0
CW02 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 RESISTORS
CW03 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 RN01 0790035R RES.CHIP 1/16W 680 OHM 0 0 0
CW04 0893179R CAP.CHIP-CERAMIC 100000PF 16V TAPE 0 0 0 RN02 0790039R RES.CHIP 1/16W 1.5K OHM 0 0 0
CW05 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 0 RN03 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0
CW06 AA00937R CAP.CHIP-CERAMIC 10UF 10V 2012BK 0 0 0 RN04 0790039R RES.CHIP 1/16W 1.5K OHM 0 0 0
CW07 AA00969R CAP.CHIP2125-B-22UF6.3V 0 0 0 RN15 0790035R RES.CHIP 1/16W 680 OHM 0 0 0
CW08 AA01116R CAP.CHIP1608-B-10UF 6.3V M 0 0 0 RN31 0790024R RES.CHIP 1/16W 100 OHM 0 0 0
CW09 0893193R CAP 1608CHIP 10000PFKB 25V TAPE 0 0 0 RN33 0790024R RES.CHIP 1/16W 100 OHM 0 0
CW10 AA01111R CERAMIC CAPACITOR(1.0UF 6.3V) 0 0 0 RN34 0790024R RES.CHIP 1/16W 100 OHM 0 0
CW11 AA01115R CAP.CHIP1608-B-4.7UF6.3V 0 0 0 RNM1 0790051R RES.CHIP 1/16W 10K OHM 0 0 0
111
DW2U
42HDS69
42HDX99
42HDS69
42HDX99
42HDT79
42HDT79
RW01 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 RW95 0790019R RES.CHIP 1/16W 47 OHM 0 0 0
RW02 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 RW96 0790019R RES.CHIP 1/16W 47 OHM 0 0 0
RW03 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 RWE4 0790019R RES.CHIP 1/16W 47 OHM 0 0 0
RW04 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 RWE5 0790019R RES.CHIP 1/16W 47 OHM 0 0 0
RW05 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 RWE6 AQ00519R CHIP RESISTOR 47OHM 0 0 0
RW06 AQ00519R CHIP RESISTOR 47OHM 0 0 0 RWE7 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RW07 AQ00519R CHIP RESISTOR 47OHM 0 0 0 RWE8 0790051R RES.CHIP 1/16W 10K OHM 0 0 0
RW08 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 RWE9 0790038R RES.CHIP 1/16W 1.2K OHM 0 0 0
RW09 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 RWF1 0790061R RES.CHIP 1/16W 56K OHM 0 0 0
RW10 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 RWF2 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RW11 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 RWF3 0790019R RES.CHIP 1/16W 47 OHM 0 0 0
RW12 0790017R RES.CHIP 1/16W 33 OHM 0 0 0 RWF4 0790019R RES.CHIP 1/16W 47 OHM 0 0 0
RW13 AQ00519R CHIP RESISTOR 47OHM 0 0 0 RWF5 AQ00519R CHIP RESISTOR 47OHM 0 0 0
RW14 AQ00519R CHIP RESISTOR 47OHM 0 0 0 RWF6 0790019R RES.CHIP 1/16W 47 OHM 0 0 0
RW15 AQ00519R CHIP RESISTOR 47OHM 0 0 0 RWF7 0790019R RES.CHIP 1/16W 47 OHM 0 0 0
RW16 AQ00519R CHIP RESISTOR 47OHM 0 0 0 RWF8 0790046R RES.CHIP 1/16W 4.7K OHM 0 0 0
RW17 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 RWP1 AQ00267R RES.CHIP 1/16W 560K OHM TAPE 0 0 0
RW18 0790064R RES.CHIP 1/16W 100K OHM 0 0 0 RWP2 AQ00247R RES.CHIP 1/16W 100K OHM TAPE 0 0 0
RW19 0790024R RES.CHIP 1/16W 100 OHM 0 0 0 RWP3 0790051R RES.CHIP 1/16W 10K OHM 0 0 0
RW20 0790024R RES.CHIP 1/16W 100 OHM 0 0 0 RWP4 0790051R RES.CHIP 1/16W 10K OHM 0 0 0
RW21 0790046R RES.CHIP 1/16W 4.7K OHM 0 0 0 RWP5 0790024R RES.CHIP 1/16W 100 OHM 0 0 0
RW22 AQ00524R CHIP RESISTOR 100OHM 0 0 0
RW23 0790031R RES.CHIP 1/16W 330 OHM 0 0 0 CRYSTALS, FILTERS
RW25 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 XWP1 BK10324R CERAMIC FILTER NFM2012P13C105BT1 0 0 0
RW26 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RW28 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 CONNECTORS, JACKS
RW29 AQ00524R CHIP RESISTOR 100OHM 0 0 0 JSW EA02231R 8P 0.45 PITCH SOCKET 3234 0 0
RW30 AQ00546R CHIP RESISTOR 4.7KOHM 0 0 0 JW01 EA03121U PCMCIA HEADER 0 0 0
RW31 0790064R RES.CHIP 1/16W 100K OHM 0 0 0 JWE1 EY01772R SD MEMORY CARD 500998-0900 0 0 0
RW32 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 PCM1 EA02331R 11P 1.0MM PITCH CONNE. 501331- 0 0 0
RW33 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 PW01 EA03014R 80P 0.5MM PITCH FPC CONNECTOR 0 0 0
RW34 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 PWS ED01055 CONNECTOR 0 0 0
RW35 0790019R RES.CHIP 1/16W 47 OHM 0 0 0
RW36 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 MISCELLANEOUS
RW38 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 #01 NA75382 DW1 TERMINAL SUP MTL. 0 0 0
RW39 0790042R RES.CHIP 1/16W 2.2K OHM 0 0 0 NW01~2 MJ03878 SCRW M3M_2*10PN+SM Unknown 0 0 0
RW40 0790042R RES.CHIP 1/16W 2.2K OHM 0 0 0
RW43 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 FINAL ASS'Y
RW45 AQ00519R CHIP RESISTOR 47OHM 0 0 0 SPEAKERS
RW46 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 SPBL GM01721 SPEAKER UNIT 0 0 0
RW47 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 SPBR GM01722 SPEAKER UNIT 0 0 0
RW48 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 SPL GM01711 SPEAKER UNIT 0 0 0
RW49 AQ00519R CHIP RESISTOR 47OHM 0 0 0 SPR GM01712 SPEAKER UNIT 0 0 0
RW51 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 MISCELLANEOUS
RW52 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 A11 JP50321 DW2-U SUBDIGITAL PWB ASS'Y 0
RW53 AQ00519R CHIP RESISTOR 47OHM 0 0 0 A12 JP50322 DW2-U SUBDIGITAL PWB ASS'Y 0
RW54 AQ00519R CHIP RESISTOR 47OHM 0 0 0 A13 JP50323 DW2-U SUBDIGITAL PWB ASS'Y 0
RW55 AQ00519R CHIP RESISTOR 47OHM 0 0 0 A21 JP50331 DW2-U FILTER PWB ASS'Y 0 0 0
RW56 AQ00519R CHIP RESISTOR 47OHM 0 0 0 A31 JP50341 DW2-U POD PWB ASS'Y 0
RW57 AQ00519R CHIP RESISTOR 47OHM 0 0 0 A32 JP50342 DW2-U POD PWB ASS'Y 0 0
RW59 AQ00519R CHIP RESISTOR 47OHM 0 0 0 A01 DD00822K FPF42C128135UA-** (PDP PANEL) 0 0 0
RW60 AQ00519R CHIP RESISTOR 47OHM 0 0 0 A02 TS07357 FPF33R-LGC85H (LOGIC BOARD) 0 0 0
RW62 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 A05 TS06023 FPF28R-SCWM3 (LOGIC SCREWS) 0 0 0
RW63 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 A21 JP50761 PSA DW2-A MAIN-DIGITAL (S/T) 0
RW64 0790064R RES.CHIP 1/16W 100K OHM 0 0 0 A22 JP50762 PSA DW2-B MAIN-DIGITAL (X) 0
RW72 0790051R RES.CHIP 1/16W 10K OHM 0 0 0 A23 JP50763 PSA DW2-C MAIN-DIGITAL (T) 0
RW73 0790051R RES.CHIP 1/16W 10K OHM 0 0 0 U1 HA01731 POW-PDP-MPF-7428 (POWER UNIT) 0 0 0
RW79 AQ00243R RES.CHIP 1/16W 68K OHM TAPE 0 0 0 FAN GS00702 3110KL-04W-B10 0 0 0
RW80 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0
RW81 AQ00231R RES.CHIP 1/16W 24K OHM TAPE 0 0 0 CONNECTORS
RW82 AQ00247R RES.CHIP 1/16W 100K OHM TAPE 0 0 0 E403 EK01931 WIRE (PROCESSED) JF04R0R021970 0 0 0
RW83 AQ00258R RES.CHIP 1/16W 270K OHM TAPE 0 0 0 E42H EF26011C ASS'Y CONNE.(SMP/PH/PA/ZH/SH/5 0 0 0
RW84 0790051R RES.CHIP 1/16W 10K OHM 0 0 0 EA01 EK01901 80P FFC CABLE L=***MM UL20861 0 0 0
RW85 AZ01031R THERMISTOR NANOSMDC050F13.2 0 0 0 ECN1 EF25781 41J LVDS CABLE L=500 (FI-W DF1 0 0 0
RW86 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 ECN1A GX00666 CLAMP FERRITE CORE K5C RC 16X2 0 0 0
RW87 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 ECN23 EF21623 10P VH CONNECTOR L=261MM #2,7NC 0 0 0
RW88 0790001R CHIP RESISTOR RECJUMPER-1-16C16T1608 0 0 0 ECN6 2908842S 9J PH CONNECTOR 270MM 0 0 0
RW89 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 EPM1 EF25971 8P EH-ZH CONNE. L=115MM 0 0 0
RW90 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 EPM2 EF25981 15P EH-DF3 CONNE. L=345MM 0 0 0
RW91 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 EPU1 EF25042 6J VH-VH CONNE. L=450MM #2,4,5 0 0 0
RW92 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 EPU1A GX00666 CLAMP FERRITE CORE K5C RC 16X2 0 0 0
RW93 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 ERF EY02262 PLUG L NIC8014N 0 0 0
RW94 0790019R RES.CHIP 1/16W 47 OHM 0 0 0 EUSB EW08516 CORD USB L=910E 0 0
112
DW2U
42HDS69
42HDX99
42HDS69
42HDX99
42HDT79
42HDT79
ACCESSORIES
E01 EV01841 POWER CORD 125V10A UL/CSA 0 0 0
E201 EY01641 PJX-IR BLASTER DP2X 0 0
E202 EY01641 PJX-IR BLASTER DP2X 0 0
E203 FQ00021 DRY BATTERY(R6P-AA) 0 0 0
E204 FR00061 DRY BATTERY R03(AB) E T 0
E301 2169513 COIL LX-ZCAT2032 0 0
ESWVL EW08432 8P PLUG CODE L=165 MM 0 0
N01 QR66761 HDS69 INSTRUCTION BOOK 0
N01 QR66771 HDT79 INSTRUCTION BOOK 0 0
N02 QR66791 HDS69 EASY GUIDE 0
N02 QR66801 HDT79 EASY GUIDE 0 0
N202 QT47722 DIRECTOR'S WARRANTY CARD 0
N203 QT44791 PLASMA WARRANTY CARD CANADA 0 0 0
N204 QT47721 NATIONAL WARRANTY CARD 0 0
U01 HL02069 REMOTE CONTROL UNIT CLU-3861WL 0 0
U01 HL02073 REMOTE CONTROL UNIT-CLU-4352UG2 0
U02 HL01864 RCT- CLU123S 0
113
DW2U
QUICK REFERENCE PARTS LIST

IC’S & UNITS
No. Symbol P# Description Function PWB ASSY Remarks

1 A21 JP50761 PSA DW2-A MAIN-DIGITAL (42HDS69) MAIN DIGITAL ASS'Y MAIN DIGITAL
2 A22 JP50762 PSA DW2-B MAIN-DIGITAL (42HDX99) MAIN DIGITAL ASS'Y MAIN DIGITAL
3 A23 JP50763 PSA DW2-C MAIN-DIGITAL (42HDT79) MAIN DIGITAL ASS'Y MAIN DIGITAL
4 DN01 CC02061R LIGHT EMITTING DIODE SML-020ML RED/ORANGE LED LED
5 DN02 CC01862R SML011BBTT86 BLUE LED LED
6 HN01 CE00121R SBX3050-02 IR RECEIVER LED
7 HN02 CZ01261R IRDA MODULE IC (RPM871-H12) IR RECEIVER LED ONLY HDT/HDX MODELS
8 HNM1 CZ01241 GP1FM514TZ0F IR RECEIVER LED
9 L9A1 BZ06251 LINE FILTER TF2722H-A152Y8R0-0 AC NOISE FILTER FILTER
10 F9A2 FN00475 FUSE 51MS 063 L-U 6.3A FUSE FILTER
11 I001 CK53531U R2S11008FP AUDIO/VIDEO SELECTOR SUBDIGITAL
12 I004 CK51331R TK11100CS ADJUSTABLE POSITIVE LOW DROPOUT REGULATOR IC SUBDIGITAL
13 I005 CK37218R MONO IC TK11150CSCL 5 V VOLTAGE REGULATOR W ON/OFF SW SUBDIGITAL
14 IH02 CK53891R TMDS SW IC CXB1441R CABLE EQUALIZER SW FRONT HDMI
15 IH03 CK37216R MONO IC TK11133CSCL 3.3 V VOLTAGE REGULATOR W ON/OFF SW FRONT HDMI
16 IH04 CK38329R DIGITAL MONOLITHIC IC (SN74LVC1G126DCK) SINGLE BUS BUFFER GATE WITH 3-STATE OUTPUTS FRONT HDMI
17 IH05 CK38329R DIGITAL MONOLITHIC IC (SN74LVC1G126DCK) SINGLE BUS BUFFER GATE WITH 3-STATE OUTPUTS FRONT HDMI
18 IL01 CK50961R SN74CB3T3306DCUR DUAL FET BUS SWITCH SUBDIGITAL
19 IM01 CK51632R 9DR32DW8-1046 IR BLASTER SUBDIGITAL ONLY HDT/HDX MODELS
20 IM02 CK51091R SN74LVC1G3157DCKR SINGLE-POLE, DOUBLE-THROW ANALOG SW SUBDIGITAL ONLY HDT/HDX MODELS
21 IM03 CK38328R IC SN74LVC1G125DCKR SINGLE BUS BUFFER GATE WITH 3-STATE OUTPUTS SUBDIGITAL ONLY HDX MODELS
22 IM04 CK38328R IC SN74LVC1G125DCKR SINGLE BUS BUFFER GATE WITH 3-STATE OUTPUTS SUBDIGITAL ONLY HDT/HDX MODELS
23 IM05 2015203R HD74HC00TELLE QUAD 2-INPUT NAND GATES SUBDIGITAL ONLY HDT/HDX MODELS
24 IM06 CK54692R GENERAL LOGIC IV(TC74AC163FT) SYNCHRONOUS PRESETTABLE 4 BIT BINARY COUNTER SUBDIGITAL ONLY HDT/HDX MODELS
25 IM07 CK51091R SN74LVC1G3157DCKR SINGLE-POLE, DOUBLE-THROW ANALOG SW SUBDIGITAL ONLY HDT/HDX MODELS
26 IM08 CK37218R MONO IC TK11150CSCL 5 V VOLTAGE REGULATOR W ON/OFF SW SUBDIGITAL
27 IP03 CK52481R TK73400TCB-G 6.2 VOLTAGE REGULATOR FOR TV / VTR USE SUBDIGITAL
28 IP05 CK50461R ANALOG MONOLITHIC IC(BA6287F) REVERSIBLE MOTOR DRIVER SUBDIGITAL ONLY HDT/HDX MODELS
29 IPT1 CK54161R ANALOG MONOLITHIC IC(MP2361DK DC-DC CONVERTER SUBDIGITAL
30 IT02 CK54051U THEATER314 QAM/VSB DEMODULATOR SUBDIGITAL
31 IT03 CK51091R SN74LVC1G3157DCKR SINGLE-POLE, DOUBLE-THROW ANALOG SW SUBDIGITAL
32 IT04 CK50961R SN74CB3T3306DCUR DUAL FET BUS SWITCH SUBDIGITAL
33 IT05 CK37218R MONO IC TK11150CSCL 5 V VOLTAGE REGULATOR W ON/OFF SW SUBDIGITAL
34 IT06 CK37605R IC TK11250CM 5 V VOLTAGE REGULATOR W ON/OFF SW SUBDIGITAL
35 IT07 CK37605R IC TK11250CM 5 V VOLTAGE REGULATOR W ON/OFF SW SUBDIGITAL
36 IT09 CK51151R UPC3221GV 5 V AGC AMPLIFIER SUBDIGITAL
37 IT10 CK51141R UPC3220GR CATV OUT-OF-BAND TUNER SUBDIGITAL
38 IT11 CK37211R MONO IC TK11118CSCL 1.8 V VOLTAGE REGULATOR W ON/OFF SW SUBDIGITAL
39 IT12 CK37216R MONO IC TK11133CSCL 3.3 V VOLTAGE REGULATOR W ON/OFF SW SUBDIGITAL
40 IY01 CK38325R DIGITAL MONOLITHIC IC (SN74LVC1G17DCK) SINGLE SCHMITT TRIGGER BUFFER SUBDIGITAL ONLY HDT/HDX MODELS
41 IY02 CK38325R DIGITAL MONOLITHIC IC (SN74LVC1G17DCK) SINGLE SCHMITT TRIGGER BUFFER SUBDIGITAL ONLY HDT/HDX MODELS
42 IY03 CK50027R DIGITAL MONOLITHIC IC (MAX202IPW) DUAL RS-232 LINE DRIVER/REC W/+-15KV ESD PROTEC SUBDIGITAL
43 IN01 CK38324R DIGITAL MONOLITHIC IC (SN74LVC1G14DCK) SINGLE SCHMITT-TRIGGER INVERTER LED
44 IN02 CK38325R DIGITAL MONOLITHIC IC (SN74LVC1G17DCK) SINGLE SCHMITT TRIGGER BUFFER LED ONLY HDT/HDX MODELS
45 IW01 CK53731U XC3S50-5PQG208C OBERON IC (POD IC) POD
46 IW02 CK38378R DIGITAL MONO IC SI-3012KM 1 A, LOW DROPOUT, 1.28~15 V REGULATOR POD
47 IW03 CK51732R MM1701CHBE 1.2 V VOLTAGE REGULATOR POD
48 IW04 CK37212R MONO IC TK11125CSCL 2.5 V VOLTAGE REGULATOR W ON/OFF SW POD
49 IWE1 CK53741R TC7MBL3245AFK OCTAL BUS SWITCH POD
50 IWE2 CK52581R ANALOG MONOLITHIC IC(MAX4790EUS) CURRENT LIMIT SWITCH POD
51 IWP1 CK50071R TPS62040DGQR HIGH EFFICIENCY STEP DOWN CONVERTER POD
52 IWP2 CK37216R MONO IC TK11133CSCL 3.3 V VOLTAGE REGULATOR W ON/OFF SW POD
53 JWE1 EY01772R SD MEMORY CARD 500998-0900 MEMORY CARD JACK POD
54 U1 HA01731 POW-PDP-MPF-7428 POWER UNIT POWER
55 UT01 HC00701 ENGD6305 ANALOG/DIGITAL TUNER SUBDIGITAL

DW2U
Part Numbers for Boards and Assemblies

PANEL BOARDS 42"
Model Power Supply X-SUS PWB X-BUS PWB Y-SUS PWB Logic PWB A-BUS-L PWB A-BUS-R PWB
42HDS69
42HDT79 HA01731 FPF33R-XSS0041 FPF33R-XBU0035 FPF33R-YSS0042 FPF33R-LGC0061 FPF33R-ABL0038 FPF33R-ABR0039
42HDX99
PANEL BOARDS 55"

Model Power Supply X-SUS PWB X-BUS PWB Y-SUS PWB SDR-U PWB SDR-D PWB LOGIC PWB
55HDS69
55HDT79 HA01751 FPF31R-XSS0031 FPF31R-XBU0029 FPF31R-YSS0032 FPF31R-SDR0033 FPF31R-SDR0034 FPF31R-LGC0053
55HDX99
A-BUS-D1 PWB A-BUS-D2 PWB A-BUS-D3 PWB A-BUS-D4 PWB A-BUS-U1 PWB A-BUS-U2 PWB A-BUS-U3 PWB A-BUS-U4 PWB
FPF31RABD002811 FPF31RABD002812 FPF31RABD002813 FPF31RABD002814 FPF31RABU002801 FPF31RABU002802 FPF31RABU002803 FPF31RABU002804
CHASSIS BOARDS 42" & 55"

1
Model Chassis Sub-Digital PWB2 AC Filter PWB POD PWB
3
Main-Digital PWB4 (Side) HDMI PWB Control PWB (Side) Terminal PWB LED / IR PWB OPT PWB
42HDS69 UE26051 JP50321 JP50341 JP50761
42HDT79 UE26052 JP50322 JP50331 JP50763
JP50342
42HDX99 UE26053 JP50323 JP50762 (Included with POD
X480401 X480402 X480403 X480404
PWB)
55HDS69 UE26054 JP50321 JP50341 JP50761
55HDT79 UE26055 JP50322 JP50332 JP50763
JP50342
55HDX99 UE26056 JP50323 JP50762
NOTES: 1. Chassis includes everything EXCEPT the Main-Digital PWB.

2. Sub-Digital PWB includes the Main Terminal Block.
3. POD means Point Of Deployment, which is another term for CableCard.
4. Main-Digital PWB is not included with Chassis.
CH 1
115
CH 2

Hitachi 42HDT79 Service Manual

Uploaded by

Copyright:

Available Formats

Hitachi 42HDT79 Service Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Hitachi 42HDT79 Service Manual

Uploaded by

Copyright:

Available Formats

What is the purpose of this document?

What is the purpose of this document?

What components does it describe?

What components does it describe?

PA No.

NTSC DW 2-U R/C: CLU-4352UG2 42HDS69

SERVICE MANUAL REVISION HISTORY INFORMATION

02.22.07 CH 3 Revised Service Menu sequence on pages 44 and 45

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT

PLASMA DISPLAY PANEL

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT

PLASMA DISPLAY PANEL

3. When service is required, observe the original lead dress.

PRODUCT SAFETY NOTICE

1. Follow the general caution recommendations from “Safety WARNING

General Servicing Guidelines 1. Immediately before handling any semiconductor

General Soldering Guidelines Removal

3. Keep the soldering iron tip clean and well-tinned. Replacement

2. Bend the two remaining leads perpendicularly to the

3. Observing diode polarity, wrap each lead of the new

Fuses and Conventional Resistor Removal/Replacement At Other Connections

3. Solder the connections.

In Critical Copper Pattern Areas Insulated Jumper Wire

At IC Connections 3. Connect insulated 20-gauge jumper wire from the

2. Carefully scratch away the solder resist and acrylic

Install Jumper Wire and Solder

3. Bend a small “U” in one end of a small-gauge jumper wire

4. Route the jumper wire along the path of the cut-away

Leadless Chip Components How to Replace Flat-lC

Information for service about lead-free solder introduction

(1) Characteristic of lead-free solder

(2) Solder for service

Caution when using solder containing lead.

(3) Soldering iron for lead-free solder.

(4) Identification of lead-free PWB

2004 models >> lead-free solder is introduced

Federal Communications Commission Notice

• Reorient or relocate the receiving antenna.

INDUSTRY CANADA AGENCY REGULATORY INFORMATION

Cable Compatible Television Apparatus- Tèlèvision câblocompatible, Canada.

Notes on Closed Caption:

Indicated Value PST(W)

Dimension Size 1 1134mm x 713.2mm x 365mm

Adjustment Settings for Video Signal 23 Picture,Contrast,Brightness,Color,Tint , Sharpness,

Settings for Sound 24 Vol, Balance, Bass.Treble, Source, Internal Speakers

S-ln(S2 Terminal) (Video/S are 51 2 InputMini Din-4P x 2

Component Signal Input 52 3 lnput:RCA pin x 9(Y of VIDEO1/2/5 is common

Auto Link 55 1 Input (VIDEO2 LINK) Auto Link Function

Audio Monitor Out Terminal 61 1 Output L/R:RCA pin x 2

FEATURES & DIFFERENCES

Remote Sound function

Downloadable Option Swivel Table Top Hotel Adjust Color Contrast

Model Spec Environment Specifications

Contrast Contrast ratio 1000 : 1 (typ)

Output Terminal Audio Line Output Sub Woofer Output 1 system

Guaranteed Temp. (Operating) 5~35°C (41F~95F)

Humidity (Stored) 20~90%RH (Non-condensing)

Atmospheric Pressure 800 to 1114hPa

<4x3 Format> <16x9 Format>

4:3 Expanded Mode

Zoom 16x9 Zoom