Viscosity Penetration Test Report

OPEN-ENDED LABORATORY
Question
You have been supplied with bitumen grade XX. You have to identify a suitable temperature for
pumping the bitumen and cater it to the mixing plant. Then, the bitumen will be spray to well-
graded aggregate.
You also have to identify a suitable temperature for mixing and compaction of asphalt concrete.
Please do an appropriate laboratory test to determine the answer.
Answer
After some researching and information gathering, the suitable testing method has been
identified, which is AASTHO T316 – 04. Viscosity Determination of Asphalt Binder Using
Rotational Viscometer
SCOPE
This test method outlines the procedure for measuring the viscosity of asphalt binders at elevated
temperature from 60 to over 200°C using a Rotational Viscometer apparatus as specified by
M 320 and R 29.
TERMINOLOGY
Viscosity - the ratio between the applied shear stress and the rate of shear is called the coefficient
of viscosity. This coefficient is a measure of the resistance to flow of the liquid. It is commonly
called the viscosity. The SI unit of viscosity is the Pascal second (Pa•s).
SUMMARY OF METHOD
This test method can be used to measure the viscosity of asphalt at application temperatures. The
torque required to maintain a constant rotational speed of a cylindrical spindle while submerged
in an asphalt sample at a constant temperature is used to measure the relative resistance to
rotation. The torque and speed are used to determine the viscosity of the binder in Pascal
seconds.
SIGNIFICANCE AND USE
1. This test method can be used to measure the apparent viscosity of asphalt at application
temperatures.
2. The measured viscosity at elevated temperatures can be used to determine

whether the asphalt binder can be handled and pumped at the refinery, terminal, or hot
mix plant facility. Measured viscosity from this procedure can be used to develop
temperature viscosity charts for estimating mixing and compaction temperatures for use
in hot mix asphalt mix design.
APPARATUS
1. Heater - A heater capable of maintaining any desired temperature setting from room
temperature to 260°C to within ±3°C.
2. Thermometers—Thermometers having a range from 60 to over 200°C and readable to

0.2°C.
3. Cylindrical spindles of various sizes for measurement of asphalt binders of different
viscosities.
4. Rotational Viscometer capable of measuring the torque required to rotate the

selected constant speed while submerged in asphalt at constant desired test temperature
and should display the viscosity in Pascal seconds automatically.
5. Temperature Controller - A proportional temperature controller capable of maintaining

the specimen temperatures t1.0°C for test temperatures ranging from 60 to 165°C or
greater.
MATERIALS
Solvent such as (Mineral Spirits or Varsol) or a degreasing spray cleaner formulated for cleaning
the sample holder, spindles and accessories.
PREPARATION OF APPARATUS
The rotational viscometer must be leveled to function properly. A bubble-type level is normally
located on top of the viscometer and is adjusted by using leveling screws located on the base.
PROCEDURE
1. Read and understand the information in the rotational viscometer manufacturer's

operating manual before proceeding.
2. Turn on the rotational viscometer and proportional temperature controller unit.
3. Preheat the sample holder with the sample chamber and the selected cylindrical spindle
according to the manufacturer's recommendation.
4. Set the proportional temperature controller to desired test temperature.
5. When the proportional temperature controller reads the desired test temperature, remove
the sample holder, and add the required amount of asphalt into the sample chamber.
6. Insert the sample chamber into the proportional temperature controller unit.
7. Insert a preheated spindle and attach it to the viscometer using the necessary coupling.
Gently lower the spindle into the asphalt so that asphalt covers the upper conical portion
of the spindle. This procedure may vary based on the manufacturer's recommendations.
8. Bring the asphalt to the desired temperature within approximately 30 minutes. Set the
viscometer speed at 20 rpm and set the display to the read viscosity in Pascal seconds
(Pa•s). This operation may be done manually or by using a software program.
9. Allow the asphalt sample to equilibrate at the desired test temperature for a minimum of 10
minutes. Begin the spindle rotation during the 10 minute temperature equilibration period.
Allow' the readings to stabilize before recording any viscosity measurements. If the observed
torque is out of range for the selected spindle and speed, change the spindle and or speed
based on the manufacturer's recommendations for the anticipated viscosity. Restart the test
with a new sample.
10. Start the test after the asphalt sample has reached the specified temperature and equilibrated
and the viscosity readings have stabilized.
11. Measure the viscosity at one-minute intervals for a total of three minutes.
DISCUSSION
The given open-ended question laboratory question acquired us to determine the suitable
mixing temperature for mixing and compacting the bitumen sample given. After some
researching and information gathering, the suitable testing method has been identified, which is
AASTHO T316 – 04.
After conducting the lab test following the procedures of AASTHO T316 – 04, the results
obtained are as follow:
Viscometer Test Results
Temperature, T Viscosity (MPa.s) Average Viscosity

30s 60s 90s
(°C) (MPa.s)
120 700 780 1110 863 ≈ 8.6P
140 500 510 500 503 ≈ 5.0P
160 330 390 310 343 ≈ 3.4P
From the result obtained above, a graph Viscosity vs. Temperature is plotted to determine
the suitable temperature for mixing and compaction. According to standard specification, the
suitable temperature for mixing and compaction is 170 °C and 280 °C respectively for bitumen
grade 80/100. However, the result obtained from the graph plotted, the temperature obtained is
172.5 °C and 203 °C. The mixing temperature is appropriate but the compaction temperature is
less than temperature stated in standard specification. This has raised the concern about the
material which been delivered to the laboratory may not fit the purchasing order. Since it does
not fit the requirement of bitumen grade 80/100, this material is not suitable for any road surface
layer construction.
CONCLUSION
The mixing temperature of bitumen is vital to determine the well mixing of the bitumen
with the aggregate. Temperature affects the viscosity of bitumen, low temperature will result in
bitumen with low viscosity which unable to mix well with aggregate to provide sufficient
bonding between those two materials, which in the end affects the quality of the road surface
layer laid with the material.
Since the result obtained raised the concern about the material which been delivered to
the laboratory may not fit the purchasing order. Since it does not fit the requirement of bitumen
grade 80/100, this material is not suitable for any road surface layer construction.
REFERENCED DOCUMENTS
1. AASHTO Standards:
 T 316 – 04, Viscosity Determination of Asphalt Binder Using Rotational
Viscometer
2. Garber N.J. and Hoel L.A. Traffic & Highway Engineering (3rd Edition). US:Brooks/Cole

Viscosity Penetration Test Report

Uploaded by

Copyright:

Available Formats

Viscosity Penetration Test Report

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Viscosity Penetration Test Report

Uploaded by

Copyright:

Available Formats

OPEN-ENDED LABORATORY

2. The measured viscosity at elevated temperatures can be used to determine

2. Thermometers—Thermometers having a range from 60 to over 200°C and readable to

4. Rotational Viscometer capable of measuring the torque required to rotate the

5. Temperature Controller - A proportional temperature controller capable of maintaining

1. Read and understand the information in the rotational viscometer manufacturer's

2. Turn on the rotational viscometer and proportional temperature controller unit.

4. Set the proportional temperature controller to desired test temperature.

Viscometer Test Results

Temperature, T Viscosity (MPa.s) Average Viscosity

You might also like