Short-Circuit Calculations

A Handbook to Accompany the

Short-Circuit Calculation Program
From MSHA’s Approval and Certification Center

By Wayne L. Carey

January 4, 2006
 Short-Circuit Calculations

Introduction

One of the jobs of the Mine Safety and Health Administration’s

(MSHA’s) Approval and Certification Center (A&CC) is to approve
electrical equipment for underground mines. An important part of this
job is to determine if circuit protective devices are sized and set
correctly. Sizing of circuit protective devices can only be done when
maximum available short-circuit current is known. Setting of the
devices can only be done when minimum available short-circuit current
is known. The A&CC has a computer program available through the
MSHA website (www.msha.gov) to calculate available short-circuit
currents in mine power systems. This program, other programs, or
hand calculation can be used to perform short-circuit calculations. Any
method used requires specific data on the mine power system. All this
data is converted to resistance and reactance values for each
component in the system. Impedance can then be calculated and then
minimum and maximum available currents. This paper describes the
data needed for each type of circuit component and how to obtain the
data. It also describes methods used by the computer program to
calculate available short-circuit currents.

Utility

The first step in analyzing a power system is to get the data for the
power available at the site, the utility data. This data can be obtained
from the power company. When calling the power company, explain
the type of information you need and ask for the engineering
department. It may be helpful to explain why you need the
information.

The power company will be able to supply this information for the point
in the power system where their responsibility for the power system
ends and the customer’s responsibility starts. A common location for
this point is the secondary of a pole or pad mounted transformer. If
the customer is responsible for the transformer, the transition point
would be the primary of the transformer. Sometimes a pole mounted
disconnect will be the transition point. The power company will specify
where in the system their responsibility ends.

The data needed is the line to line voltage (VLL), short-circuit kVA
(kVASC), and X/R. Obtaining the voltage is simple enough. Short-
circuit kVA is the power available at a bolted three phase fault. Bolted
means all three phases connected together with no added impedance.

2
X/R is the ratio of reactance to resistance in the supply. Short-circuit
kVA and X/R may need to be derived from other data.

Short-circuit current (ISC) is sometimes supplied by the power company

rather than short-circuit kVA. This current is the current in one phase
of a three phase bolted fault. The short-circuit kVA can be calculated
from the short-circuit current using the following equation.

3 ∗ I SC ∗ VLL
kVA SC = (Eq. 1)
1000

If you’re not doing these calculations every day, it is sometimes hard

to remember when to include the square root of three factor. Power in
a three phase circuit is three times the single phase power or three
times the current in one phase times the line to neutral voltage (VLN).
The line to neutral voltage is the line to line voltage divided by the
square root of three.

3 ∗ I SC ∗VLN 3 ∗ I SC V LL 3 ∗ I SC ∗VLL
kVA SC = = ∗ = (Eq. 2)
1000 1000 3 1000

Power factor (PF) is sometimes specified instead of X/R. This must be

the short-circuit power factor. Power factor is defined as the cosine of
the angle between voltage and current. X/R is the tangent of this
same angle. X/R can be found from power factor by taking the tangent
of the inverse cosine of the power factor.

X / R = tan ( cos −1 PF ) (Eq. 3)

When neither X/R nor power factor are specified for the utility, it is
usually safe to assume the impedance of the utility is all reactance and
X/R is infinite. Unless there are many miles of transmission line, the
impedance of the utility will be mainly reactance in the generator. This
is all the data needed for the utility. From this data, the short-circuit
calculation program can be used to calculate impedance (Z),
resistance (R), and reactance (X). This data can also be calculated
manually.

Impedance is calculated from VLL and short-circuit kVA.

VLL2
Z= (Eq. 4)
kVASC ∗1000

3
Resistance and reactance are then calculated from the impedance
using X/R.

Since: Z= X 2 + R 2 (Eq. 5)

Z
R= (Eq. 5a) And X = R ∗ ( X / R) (Eq. 5b)
1 + ( X / R)
2

Resistance and reactance are calculated at the voltages for the points
in the circuit where the short-circuit currents are calculated. For
example, even though the utility voltage may be 69 kilovolts (kV), if
the short-circuit currents are being calculated further down the circuit
where the voltage is 2400 volts, the resistance and reactance will be
calculated at 2400 volts. The computer program initially calculates
resistance and reactance for the utility at the utility voltage. As the
program works down through a circuit, encountering transformers, it
converts the resistance and reactance to the new voltage by
multiplying by the ratio of the voltages squared.

V22
R2 = R1 ∗ (Eq. 6)
V12

Where: R2 = resistance at secondary voltage

R1 = resistance at primary voltage
V2 = secondary voltage
V1 = primary voltage

This formula is the result of conservation of energy. Energy into the

transformer (V12/R1) equals energy out of the transformer (V22/R2).

Transformers

Transformers are specified by output voltage (V), kVA rating, percent

impedance (%Z), and X/R ratio. The X/R ratio is the ratio of reactance
to resistance. This information, with the exception of X/R, is usually on
the transformer nameplate. If X/R is not specified on the nameplate,
the transformer manufacturer may be able to supply this. When
contacting the transformer manufacturer, it may be helpful to have the
transformer serial number. If X/R cannot be obtained, a value of 4.9 is
typical and can be used in calculations. Impedance (Z) is calculated
from V, kVA, and %Z.

% Z ∗V 2 %Z V 2
Z = Or Z = * (Eq. 7)
kVA ∗100 ,000 100 VA

4
Resistance and reactance are then calculated from Z and X/R as they
were for the utility. Again, these resistances and reactances are for a
short-circuit at the secondary of the transformer. If the short-circuit is
at a point further down the circuit and after another transformer, the
voltage at the short-circuit should be used in equation 7. Alternatively,
the calculated resistances and reactances can be converted to the new
voltage by multiplying by the ratio of the voltages squared.

Three Winding Transformers

The most common three winding transformers used in mining are

located in underground power centers. They are usually specified like
two separate transformers with no interwinding impedance. They can
be modeled as two separate transformers. When three winding
transformers have separate interwinding impedance specified, it is
usually specified as reactance (X) and resistance (R) in ohms. Three
sets of X and R must be supplied; primary-secondary (ps), primary-
tertiary (pt), and secondary-tertiary (st). Xps and Rps are measured in
the primary with the secondary short-circuited and the tertiary open.
Xpt and Rpt are measured in the primary with the tertiary short-circuited
and the secondary open. Xst and Rst are measured in the secondary
with the tertiary short-circuited and the primary open. The three
winding transformer is modeled as follows.

The impedances are related by the following formulas.

Z ps = Z p + Z s (Eq. 8a)
Z pt = Z p + Z t (Eq. 8b)
Z st = Z s + Z t (Eq. 8c)

Z p = 0.5 ∗ ( Z ps + Z pt − Z st ) (Eq. 8d)

Z s = 0.5 * ( Z ps + Z st − Z pt ) (Eq. 8e)
Z t = 0.5 * ( Z pt + Z st − Z ps ) (Eq. 8f)

In the equations, all impedances must be referred to a common

voltage. Note that Xst and Rst are measured at the secondary voltage.

5
If all impedances are to be at the primary voltage, Xst and Rst must be
transferred.

Cables

The minimum data needed for cables is size, length, voltage rating,
and type. Size, voltage rating, and type of cables is embossed into the
jacket. Size and type of aerial cable may be shown on a drawing or
listed on an invoice. Lengths may be measured, determined from mine
maps, or paced off and estimated. Some cables such as types SHD
and MPF have different constructions for different voltage ratings and
the voltage rating will need to be specified. It will be embossed in the
cable jacket. It should be noted if more than one cable is used in
parallel. The spacing of conductors of aerial cable will affect
inductance. The computer program uses a default spacing of three
feet. If the spacing is different than three feet, it should be noted. The
computer program has stored values for resistance and reactance per
thousand feet for most commonly used cable types. This data is also
available in cable standards and manufacturer’s specifications.
Resistance is specified at ambient temperature.

Cable operating temperature has an effect on the resistance of a cable.

Most cables have a rated operating temperature of 90 °C. Aerial cable
is rated 75 °C. If different operating temperature ratings are specified,
they should be noted. The computer program uses fully loaded cables
at their rated operating temperature to calculate minimum available
currents. The cables have higher resistances at their rated operating
temperature ratings than at ambient temperature. The resistance at
rated operating temperature can be calculated from the resistance at
ambient temperature using the following formula.

R2 = R1 [1 + α ( T2 − T1 ) ] (Eq. 9)

Where: R2 = resistance at operating temperature

R1 = resistance at ambient temperature
T2 = rated operating temperature
T1 = ambient temperature
α= temperature coefficient of resistivity corresponding to
temperature T1 (0.00393 for copper at 20 °C)

When calculating maximum available current by hand, the resistance

of the cable at ambient temperature should be used. However, the
current that causes the cable to reach its highest temperature may not

6
be the maximum available current. If the cable is initially at a
temperature between ambient and its rated operating temperature
and a short-circuit occurs, it is possible that the cable will reach a
higher final temperature at a current lower than the maximum
available current. The current depends on the cable’s resistance, but
the resistance depends on the current. Therefore, the computer
program calculates current that causes maximum temperature with an
initial temperature of ambient and with an initial temperature at one
degree increments up to the cable’s rated operating temperature. This
is one place where the power of the computer really comes in handy.
The computer program also uses the subtransient reactance
(discussed below) to calculate temperature after one cycle of short-
circuit. This temperature is used as the initial temperature along with
transient reactance in an additional calculation to calculate
temperature at the end of the short-circuit (when the circuit protective
device opens). The maximum available current calculated in the
computer program is actually the current that causes maximum
temperature.

Reactance of most cables is published by the manufacturer. The

reactance in ohms per 1000 feet of aerial cables with one foot spacing
can be found with the following formula.

 1 
X L = 0.02298 ∗ ln   (Eq. 10)
 GMR 

GMR is the geometric mean radius in feet. It can be calculated by

multiplying the wire O.D. in inches by .03245.

GMR ≅ R ∗ e −0.25 ≅ 0.3894 ∗ D ≅ 0.03245 ∗ d (Eq. 11)

Where: R = wire radius in feet

D = wire diameter in feet
d = wire diameter in inches

The reactance of aerial cable depends on the spacing between wires.

Reactance at spacings other than one foot can be calculated with the
following formula.

 
 ln ( spacing ) 
X new = X old 1 +  (Eq. 12)
  1 
 ln  
  GMR   

7
 Motors

Motors are a source of short-circuit current. They will act like

generators when a short-circuit occurs. At a minimum, motors must be
specified by horsepower which will be listed on the motor nameplate.
Their reactance may also be specified. Motors have two values of
reactance, subtransient and transient. Subtransient reactance is the
reactance of the motor during the first cycle of the short-circuit.
Transient reactance is the reactance of the motor during the remainder
of the short-circuit. The computer program supplies typical values of
subtransient and transient reactance for motors. Resistance is
considered to be negligible. AC motors may be further identified as
induction or synchronous. Synchronous motors can be 6-pole or 8- to
14-pole. The subtransient and transient reactance will vary depending
on whether the motor is induction, 6-pole synchronous, or 8- to 14-pole
synchronous. It also varies between induction motors rated less than
or equal to 600 volts and induction motors rated greater than 600
volts. Induction motors will not contribute to a short-circuit after the
first cycle. Typical values of reactance are listed in Table 11.

Type of Motor Subtransient Transient

Reactance (per Reactance
unit) (per unit)
DC 0.15 0.30
6-pole Synchronous 0.15 0.23
8- to 14-pole Synchronous 0.20 0.30
Induction ≤600 Volts 0.25 -
Induction >600 Volts 0.17 -

Table 1

Subtransient and transient reactances are usually given in per unit

values. The actual value of reactance can be found with the following
formula.

X PU ∗ V 2
X = (Eq. 13)
746 ∗ HP

Where: XPU = per unit reactance

V = voltage
HP = horsepower

Subtransient reactance should be used to calculate maximum available

short-circuit current. Minimum available short-circuit current does not
usually include contributions from motors, but when it does, transient

8
reactance should be used in the calculation. A&CC does not include
motor contribution in minimum available short-circuit current. When
adding impedances working down through a circuit, the impedance of
a motor should be added in parallel with the total impedance up to the
point in the circuit where the motor contributes. This reduces the
impedance at that point. Adding impedances in parallel is most easily
done by first converting resistance and reactance to conductance and
susceptance, adding the conductances and susceptances, and
converting the conductance and susceptance back to resistance and
reactance. Conductance, susceptance, resistance, and reactance are
related by the following formulas.

R X
G= (Eq. 14a) −B = (Eq. 14b)
R2 + X 2 R2 + X 2

G −B
R= (Eq. 14c) X = (Eq.14d)
G + B2
2
G + B2
2

Where: R = resistance
X = reactance
G = conductance
B = susceptance

Generators

Generators are treated just like motors. They are specified by kVA,
subtransient reactance, and transient reactance. The kVA will be listed
on the generator nameplate. Table 2 lists typical values of reactance
for dc and four types of ac generators2. The four types are two-pole
turbine, four-pole turbine, salient pole with dampers and salient pole
without dampers.

Type of Generator Subtransient Transient

Reactance (per Reactance (per
unit) unit)
DC 0.15 0.30
2-Pole Turbine 0.09 0.15
4-Pole Turbine 0.14 0.23
Salient Pole with Dampers 0.20 0.30
Salient Pole without 0.30 0.30
Dampers

Table 2

Reactance is calculated with the following formula.

9
 X PU ∗ V 2
X = (Eq. 15)
1000 ∗ kVA

Where: XPU = per unit reactance

V = voltage
kVA = kilovolt-ampere rating

Capacitors

Capacitors are specified by kVAR on their nameplates. This is kVA

reactive. If no tolerance is specified, 15% may be used. Capacitors
will feed a short-circuit just like motors and generators. The following
formula calculates reactance for a capacitor using a tolerance of 15%.

V 2 ∗1.15
X = (Eq. 16)
kVAR ∗1000

Where: V = voltage
kVAR = kilovolt-amperes reactive

Rectifiers

Efficiency is the only rating needed for rectifiers. If no efficiency rating

is specified, 99% can be assumed. Current through the rectifier is
reduced by the factor Efficiency (%) / 100.

Minimum Available Current

Minimum available current is calculated for a line to line arcing fault

using the following formula.

0.95 ∗ VLL
I MIN = (Eq. 17)
2 ∗ Z MAX

Where: VLL = line to line voltage

ZMAX = maximum impedance

This formula is used for AC and the DC output from a three phase
rectifier. The factor of 0.95 accounts for voltage fluctuations. The
maximum impedance is calculated from the maximum resistances and
reactances for all the elements in the circuit. For AC circuits, the
current is further reduced by multiplying by an arcing fault factor, KA.
This factor is listed in Table 3 for various voltages3.

10
 Voltage (V) KA
V ≤ 480 0.85
480 < V ≤ 0.90
600
600 < V ≤ 0.95
1040
1040 < V 1.0

Table 3

For DC circuits the arc voltage depends on the current. First, the
current is calculated with Equation 17. If the calculated current is
greater than or equal to 600 amperes, the arc voltage is 60 volts. If
the calculated current is less than 600 amperes, the arc voltage is
calculated with the following formula4.

 ( 1842 − I ) 

V ARC = e
 303 
  (Eq. 18)

Where: I = initially calculated current

The voltage is then reduced by the arc voltage and the available
current is recalculated.

Maximum Available Current

Maximum available current for AC circuits is calculated for a three-

phase bolted fault using the following equation.

V LL
I MAX − AC = (Eq. 19)
3 ∗ Z MIN

Where: VLL = line to line voltage

ZMIN = minimum impedance

Maximum available current for DC circuits is calculated for a line to line

bolted fault using the following equation.

V LL
I MAX −DC = (Eq. 20)
2 ∗ Z MIN

Where: VLL = line to line voltage

ZMIN = minimum impedance

11
 Example

A mine is supplied 95 MVA of power at 34.5 kV with an X/R ratio of

5.23. The power travels 1200 feet through number 2, ACSR aerial
cable with three-foot spacing to a substation. The substation has a
secondary voltage of 12.47 kV and is rated 10 MVA with 6.08%
impedance. The power then travels 6000 feet through number 2/0, 15
kV, mine power feeder cable to an underground power center. The
power center has a secondary voltage of 1040 volts and is rated 1350
kVA with 5.0% impedance. Power then travels 850 feet through
number 2/0, 2 kV, shielded trailing cable to a continuous miner. If a
short-circuit occurs on the continuous miner at the point where the
trailing cable ends, what are the minimum and maximum available
short-circuit currents?

Figure 1

12
1. Starting at the utility, calculate the impedance using equation 4.
Remember to use the voltage at the short-circuit, 1040 volts.

V LL2 1040 2
Z = = = 0.0114 Ω
kVA ∗1000 95,000 ∗1000

From the impedance and X/R ratio, find X and R.

Z .0114
R= = = 0.0021 Ω
1 + ( X / R) 1 + 5.23 2
2

X = R ∗ ( X / R ) = 0.0021 ∗ 5.23 = 0.0112 Ω

2. Now, find the reactance and minimum and maximum resistance

for the aerial cable. The GMR must first be found with Equation
11. From manufacturer’s specifications, the O.D. of number 2,
ACSR wire is 0.316 inch.

G M ≅R0.0 3 2 4∗ d5 = 0.0 3 2 4∗ 05.3 1 "6= 0.0 1 0' 3

The reactance is then found with Equation 10.

 1   1 
X L = 0.02298 ∗ ln   = 0.02298 ∗ ln   = 0.105 Ω
 GMR   0.0103 

Since this is the impedance for one-foot spacing, you must

correct for three-foot spacing using Equation 12.

   
 ln ( spacing )   ln (3) 
X new = X old 1 +  = 0.105 ∗1 +  = 0.1304 Ω
  1    1 
 ln   ln  
  GMR   

  0.0103 


The reactance of 1000 feet of number 2, ACSR aerial cable is

0.1304Ω. The reactance for 1200 feet is 1.2 * 0.1304 = 0.1565Ω.
This needs to be converted from the overhead line voltage to the
voltage at the short-circuit.

1.04 2
X = 0.1565 ∗ = 0.0001 Ω
34 .5 2

From the manufacturer’s specifications, the resistance of number

2, ACSR aerial cable is 1.753 Ω per mile at 75 °C. The resistance
of 1200 feet is 0.3984 Ω at 75 °C. Multiplying by the ratio of the

13
 voltages squared gives a maximum resistance of 0.0004 Ω. To
get the minimum resistance, the resistance at 75°C must be
converted to the resistance at 20 °C using Equation 9.

R75 0.0004
R20 = = = 0.0003 Ω
1 + α ( 75 − 20 ) 1 + 0.00393 * 55

3. The next component in the system is the substation. First, find

the impedance using Equation 7.

% Z ∗V 2 6.08 * 1040 2
Z = = = 0.0066 Ω
kVA ∗100 ,000 10 ,000 * 100 ,000

The X/R ratio is not specified for the substation. A value of 4.9
can be assumed. Using this value and the impedance, find X and
R.

Z .0066
R= = = 0.0013 Ω
1 + ( X / R) 1 + 4.9 2
2

X = R ∗ ( X / R ) = 0.0013 ∗ 4.9 = 0.0065 Ω

4. Next is the 6000 feet of number 2/0, 15 kV, mine power feeder
cable. From manufacturer’s specifications, reactance of 1000
feet of this cable is 0.038 Ω. The reactance of 6000 feet at 1040
volts is calculated as follows:

1040 2
X = 6 * .038 * = 0.0016 Ω
12 ,470 2

From manufacturer’s specifications, resistance of this cable at

20°C is 0.0792 Ω per 1000 feet. Resistance of 6000 feet at 1040
volts would be:

1040 2
RMIN = 6 * 0.0792 * = 0.0033 Ω
12 ,470 2

The maximum resistance will be at 90 °C, the rated operating

temperature of mine power feeder cable.

R MAX = R MIN * [1 + α ( 90 − 20 ) ] = 0.0033 * (1 + 0.00393 * 70 ) = 0.0042 Ω

5. The power center is the next component in the circuit. First find
the impedance.

14
 % Z ∗V 2 5 * 1040 2
Z = = = 0.0401 Ω
kVA ∗100 ,000 1350 * 100 ,000

The X/R ratio is not specified for the substation. A value of 4.9
can be assumed. Using this value and the impedance, find X and
R.

Z 0.0401
R= = = 0.0080 Ω
1 + ( X / R) 1 + 4.9 2
2

X = R ∗ ( X / R ) = 0.0080 ∗ 4.9 = 0.0393 Ω

6. Last is the 850 feet of number 2/0, 2 kV, shielded cable. From
manufacturer’s specifications, reactance of 1000 feet of this
cable is 0.031 Ω. The reactance of 850 feet is 0.85 * 0.031 =
0.0264 Ω. From manufacturer’s specifications, resistance of this
cable at 20°C is 0.0839 Ω per 1000 feet. The minimum
resistance (RMIN) of 850 feet is 0.85 * 0.0839 = 0.0713 Ω. The
maximum resistance is the resistance at the 90 °C rated
operating temperature of mine power feeder cable.

R MAX = R MIN * [1 + α ( 90 − 20 ) ] = 0.0713 * (1 + 0.00393 * 70 ) = 0.0909 Ω

7. Now that all the resistances and reactances are calculated, we

total them and calculate impedances and available currents.

Component Minimum Maximum Reactance (Ω)

Resistance (Ω) Resistance (Ω)
Utility 0.0021 0.0021 0.0112
Aerial Cable 0.0003 0.0004 0.0001
Substation 0.0013 0.0013 0.0065
Mine Power Feeder 0.0033 0.0042 0.0016
Cable
Power Center 0.0080 0.0080 0.0393
Trailing Cable 0.0713 0.0909 0.0264
Total 0.0863 0.1069 0.0851

Table 4

Z MIN = 2
RMIN + X 2 = 0.0863 2
+ 0.0851 2 = 0.1212 Ω

Z MAX = 2
RMAX + X 2 = 0.1069 2
+ 0.0851 2 = 0.1366 Ω

15
 0.95 ∗ K AV LL 0.95 * 0.95 * 1040
I MIN = = = 3436 Amperes
2 ∗ Z MAX 2 * 0.1366

V LL 1040
I MAX = = = 4954 Amperes
3 ∗ Z MIN 1.732 * 0.1212

Conclusion

Accurate calculations of available short-circuit currents can be made

without a power systems specialization in electrical engineering.
Symmetrical components and the per-unit system can be left for more
advanced analyses. Hand calculations can still be tedious though. A
computer program can make short work of the calculations.

16
 References

1. Recommended Practice for Electric Power Distribution for

Industrial Plants, Std. 141-1976, IEEE, 1976.

2. Electrical Transmission and Distribution Reference Book, East

Pittsburgh, PA, Westinghouse Electric Corporation, 1964.

3. William S. Vilcheck, George Fesak, and William J. Helfrich,

“Instantaneous Circuit Breaker Settings for the Short-Circuit
Protection of Three-Phase 480-, 600-, and 1040-V Trailing
Cables,” IEEE Transactions on Industry Applications Volume IE-17
No. 4, pp. 362-368, IEEE, July/August, 1981.

4. George Fesak, William S. Vilcheck, William J. Helfrich, and David

C. Deutsch, “Instantaneous Circuit Breaker Settings for the Short-
Circuit Protection of Direct Current 300- and 600-V Trailing
Cables,” IEEE Transactions on Industry Applications Volume IE-17
No. 4, pp. 369-375, IEEE, July/August, 1981.

17