POWER PLANT INSTRUMENTATION(EI1002)

SEMESTER VIII

1. Name the four major circuits in steam power plant. Coal and ash circuit Air and flue gas circuit Feed water and steam circuit Cooling water circuit 2. What consists of cooling water circuit and coal & ash circuit in steam power plant? The cooling water circuit consists of a pump, condenser and cooling tower. The coal and ash circuit consists of coal delivery, preparation of coal, handling of coal to the boiler furnace, ash handling and ash storage. 3. What is the main purpose of the reservoir? The main purpose of reservoir is to store water received from catchments areas during the rainy seasons and supply the same during the dry season. 4. What is the main purpose of the dam? The main purpose of the dam is to increase the height of water level and also to increase the working head of the hydraulic power plant. 5. What is the use of surge tank? The surge tank is used to provide better regulation of water pressure in the system. The surge tank controls the water when the load on the turbine decreases and supplies water when the load on the turbine increases. Thus, surge tank controls the pressure variations resulting from the rapid changes in water flow in penstock and hence prevents water hammer. 6. Explain about penstock? The pipe between surge tank and prime mover is known as penstock. It is designed t o withstand high pressure. It is made up of reinforced concrete. In very cold areas, the penstock is buried to prevent ice formation and to reduce the expansion joints.

7. What is the use of spill Ways? Spillway is like a safety valve of the dam. It discharges major flood without damaging the dam. It keeps the reservoir level below the maximum level allowed. 8. What is the main purpose of high-pressure boilers? The high-pressure boilers are used to increase the efficiency of the plant and to reduce the cost of electricity production. 9. State important advantages of high-pressure boilers? The amount of scale formation is less, since the velocity of water through pipes are more. All parts of the system are heated uniformly, so there is no danger of overheating. 10. Name important high pressure boilers? La Mont boiler Benson boiler Loeffler boiler Velox boiler. 11. Name the different types of coal transforming equipments? 1. Belt conveyors 2. Screw conveyors 3. Bucket elevators 4. Grab bucket elevators 5. Skip hoists 6. Flight conveyors. The coal transfer starts by carrying of coal from-unloading point to the storage site.

12. Define forced draft and induced draft cooling towers If the fan is located at the bottom of the tower and air is blown by the fan up through the descending water it is called as forced draft cooling towers If the fan is located at the top of the tower and air enters through the louvers located on the towers side and drawn up and discharge through the fan casing, it is called as induced draft

13. Write about isotopes of an element? Some elements have the same number of protons in the nucleus but different number- of neutrons. As a result, these elements have the same atomic number but different mass number.Such type of elements which ' have the same atomic number same number of protons the -same chemical properties but different mass numbers due to different number of neutrons, are known as I the isotopes of an element.

14. What are the requirements to sustain fission process? The bombarded neutrons must have sufficient energy to cause fission The number of neutrons produced must be able to create the rate of fission The fission process must generate energy The fission process must be controlled 15. What are the desirable properties of a good moderator? It must be as light as possibleIt must slowdown the neutron as quick as possible It must have resistance to corrosion It must have good machinability It must have good conductivity and high melting point 16. What are the desirable properties of a coolant? It should not absorb neutron Have high chemical and radiation stability Non-corrosive Have high boiling point Non-toxic 17. Name few types of reactors. Fast reactors, Thermal reactors, natural fuel reactors, Enriched Uranium reactors, water moderated reactors, heavy water moderated reactor, graphite moderated reactor, gas cooled reactors and Sodium cooled reactors. 18. What is the purpose of control rods? The control rods are used to start the chain reaction, maintain the chain reaction at required level and to shut down the reactor during emergency.

19. What is meant by Nuclear fission? Uranium exists in different isotopes of U238, tP34 and U235. Out of these, EP35 is most unstable. When unstable heavy nucleus is bombarded with high-energy neutrons, it splits up roughly into two equal fragments and about 2.5 neutrons are released and a large amount of energy is produced. This process is called nuclear fission. 20. Name the different components of nuclear reactor? 1. Nuclear fuel 2. Moderator 3. Control rods 4. Reflectors 5. Reactor vessel 6. Biological shielding 7. Coolant 21. State some advantages of Pressurized Water reactor? The pressurized water reactor is compact In this type, water is used as coolant, moderator and reflector water is cheap and available in plenty) It requires less number of control rods. 22. What are the advantages of gas cooled reactor nuclear power plant? 1. Fuel processing is simple 2. The use of C02 as coolant completely eliminates the possibility of explosion in reactor. 3. No corrosion problem 23. What is breeding in nuclear reactor? The process of producing fissionable material from a fertile material such as uranium 238 (U238) and thorium 232 (Th 232 ) by neutron absorption is known as breeding. 24. Name the coolants commonly used for fast breeder reactors? Liquid metal (Na (or) Na K) Helium (He) Carbon dioxide.

25. Define speed. Speed is a variable which refers to the revolutions per minute of some piece of rotating equipment. 25. Which is the most frequently used speed measuring instrument? Tachometer 27. What are the types of tachometer? a) A.C. tacho generator b) D.C. tacho generator 28. What are the types of D.C.tacho generator? a) Permanent magnet type b) Separately excited field type 29. What are the disadvantages of D.C. tacho generator? A.C. ripple is present in the output signal. The magnitude of the ripple is 2% of the out[ut D.C.level. 30. Name the types of rotor used in A.C.tacho generators. a) Drag cup rotor b) Squirrel cage rotor 31.What are the advantages of Squirrel cage rotor? *Cheaper *Occupies less space

32. Give some applications of drag cup tacho generator. It is commonly used in the speedometers of motor vehicles and as a speed indicator for aeroengines. 33. Give the formula to calculate the shaft speed. Shaft spped = (disk speed * No. of openings in the disk) / No.of images 34. Define torque. Torque is defined as the force which tends to change the linear motion or rotation of a body. 35. What is the other name for inline stationary torque sensor? Relative regular twist torque sensor 36. What are the types of torque transducer? i) ii) iii) iv) Inline rotating torque sensor Inline stationary torque sensor Optical torque sensor Proximity torque sensor

37. Write the relationship between torque and force. T=F.D where T -> Torque F -> Force

D -> Perpenticular distance between the axis of rotation of the line of action of the force 38. What are the advantages of optical torque sensor? Low cost, small physical size 39. Write the formula for determining the actual speed in a stroboscope. Actual speed ,fr =fl fn (n-1) / ( fn - fl ) fn is the highest flashing speed fl is the lowest flashing speed n is the no. of flashing frequencies 40. Define load cell. Load cell are devices that convert force into pressure , which are then measured. 41. Write down the range, accuracy and resolution in hydrostatic or hydraulic load cell. Range of force measurement = 0 to 30000 N Accuracy Resolution = 0.1% = 0.02%

42. Why magneto elastic load cell is also called pressductor load cell? The degree of change has a direct relationship with the applied stress or force. So it is called pressductor load cell.

43. What are the advantages of magneto elastic load cell? Extremely robust transducer Produces relatively high output signal levels Overload ratings are as high as 15 times the rated loads

44. What are the advantages of using Baume sclae? It is used for liquids both higher and heavier than water. 45. Write the abbreviation of API scale. API - American Petroleum Institute 46. Write the disadvantages of bridge type gas densitometer. The major disadvantage is that the variations in ambient temperature will introduce errors. 47. Write the formula for determining the height in a pressure head type densitometer. H = Span / Specific gravity maximum - Specific gravity minimum 48. Give some of the materials which are used for the manufacturing of a float. Pyrex, Plastic 49. For what purpose accelerometers are used? For the measurement of shock & vibration For gross measurement of acceleration of vehicles like aircraft, submarines etc.

50. What are the advantages of LVDT?

It is used for steady state and low freequency vibration measurements. Smaller amss, so, it is used for the measurement of vibrations of higher frequencies.

51. Define piezo electric effect. If the dimension of crystal are changed by the application of a mechanical force, an electrical potential appears across the crystal. This effect is called piezo electric effect. 52. What are the features of piezo electric accelerometers? Small in size and weight It can be used for vibration and shock measurements.

High output impedence Their response is poor at low frequencies

53. List some of the applications of strain gauge accelerometers. It is used for the measurement of acceleration and vibration in vehicles, aircrafts, bridges, hoists, cranes & lifts. 54. Seismic instrument can be used as accelerometer &vibrant True or false. True 55. What are the two modes of seismic instrument? ( i ) Displacement mode ( ii ) Acceleration mode 56. Define density. It is defined as the mass per unit volume of a substance under fixed conditions. 57. Define specific gravity. It is defined as the ratio of density of one substance to the density of another reference substance both obtained at same temperature & pressure. 58. What is the other name for specific gravity? Relative density. 59. Define viscosity. It is the property of the fluid which gives the resistance to the flow. 60. What are the units of density?

Kg/m3 or gm/litre or gm/ml 61. What are the units of viscosity? Pascal or 1NSM-2 or 1kgm-1 or poise 62. For what purpose mechanical type vibration instruments are used? It is used for the measurement of ( a ) Motion of 2 points w.r. to each other (relative motion ) ( b ) Motion w.r. to earth (absolute motion )

63. Write down the excitation voltage and accuracy of strain gauge load cell. Excitation voltage may be a.c. or d.c in the range of 5 to 25 volts. Accuracy is +0.1% of the full scale output. 64.What are the main parts of an electrical pressure transducer? (a) Pressure sensing element such as a bellow, a diaphl11gm or a bourdon tube. (b) Primary conversion element. e. g resistance or voltage. (c) Secondary conversion element. 65. What are the advantages of strain gauge pressure transducer? (i) Small & easy to install (ii) Good accuracy (iii) More stable (iv) Fast speed response (v) Simple to maintain 66. What are the disadvantages of strain gauge pressure transducer? (i) High cost (ii) Requires constant voltage supply. (iii) Electrical readout is necessary. (iv) Temperature compensation is required.

67. What is the principle of operation of a piezoelectric pressure transducer? When pressure is applied to a piezoelectric crystal such as quartz, an electrical charge is generated. 68. What are the types of thermal conductivity gauges? (a) Pirani gauge (b) Thermocouple gauge 69. What is the purpose of ionization gauge? Ionization gauge is used to measure the density of a gas.

70. Write down the formula for calculating the pressure in a Mcleod gauge? P = KHHo(1- KH) K->Constant H-> Difference in heights of the two mercury columns. Ho->Height of the top of the closed capillary tube above the line marked on the tube. 71. What is the function of a dead weight tester? Dead weight tester is used to calibrate bourdon gauges .It is used as a measuring device and also as a calibration method. 72. What are the disadvantages of using thermocouple gauge? (i) Easily damaged by organic vapours (ii) The filaments can be coated with a deposit of devapourised vapours which alters the way the filament transfers heat. 73. Define thermal conductivity The ability of the material to carry heat by conduction is called as the thermal conductivity. 74. What are the materials used in the construction of piezoelectric pressure transducer? These devices use piezoelectric characteristic of crystalline and ceramic materials such as quartz.

75. What are the main parts in electrical pressure transducer? (i)Pressure sensing element such as a bellow, a diaphragm or a bourdon tube. (ii)Primary conversion element (iii)Secondary conversion element. 76. What are the advantages of capacitive pressure transducer? It gives rapid response to changes in pressure It can withstand a lot of vibration It has a good frequency response and can measure both static & dynamic changes.

77. What is a vacuum pressure? Pressure which are below the atmospheric pressure are called vacuum pressure. 78. What is the purpose of calibrating a pressure measuring instrument? It is used to adjust the output signal to a known range of pressure. It includes zero, span and linearity adjustment. 79. Write down the applications of ionization gauges? It is used to measure low vacuum and ultra high vacuum pressure. 80. Determine the range of pressure which can be measured by pirani gauge & thermocouple gauge In pirani gauge-> Pressure range from 10-5 torr to 1 torr can be measured. In thermocouple gauge-> Pressure range from 10-4 torr can-be measured. 81. What are the disadvantages of LVDT pressure transducer? Large core displacement are required for appreciable amount of differential output. Temperature affects the performance of the transducer. They are sensitive to stray magnetic fields. 82.What is the principle of operation of a capacitive pressure transducer? It is based on the principle of the familiar capacitance equation of the parallel plate capacitor (ie) C=0rA/d farad

(ie) capacitance = A/d 0=8.85*exp(-12)f/m2 r=Dielectric constant A ->Area of each plate d->Distance between two plates. 83.Write the principle of operation of an ionization gauge? It follows Boyle's law (i.e) at constant temperature, the ratio of pressure of
two gases is equal to the ratio of the two densities.

84. Define temperature? The temperature of a substance is a measure of hotness or coldness of that substance. 85. What is the difference between temperature and heat? Temperature is defined as degree of heat. Heat is used to mean quantity of heat. 86. What are the temperature scales? Lower fixed point or ice point. Upper fixed point or steam point. 87. Give the relationship between Celsius scale & Fahrenheit scale?
0C/100=0F-32/180

88. Write the relationship between Kelvin scale & Rankine scale? R=0F+459.69 89. Define triple point? A particular temperature and pressure at which three different phases of one substance can exit in equilibrium is known as triple point. 90. Write some methods of measurement of temperature? Expansion Thermometer. Filled system Thermometer. Electrical Thermometer. Pyrometer. 91. What are the different types of filled system Thermometer?

Gas-filled Thermometer. Liquid-filled Thermometer. Mercury-filled Thermometer. Vapour-filled Thermometer. 92. How radiation error occurs? It occurs due to the temperature difference between bulb and other solid bodies in filled system Thermometer. 93. Define Seeback effect? If two dissimilar metals are joined together to form a closed circuit, there will be two junction where they meet each other. If one of these junctions is heated, then a current flow in the circuit which can be detected by a galvanometer. The amount of current depends on the difference in temperature between the two junctions and on the charactSeristics of the two metals. This was observed by Seeback & hence known as Seeback effect. 94. Which effect is used in thermocouple? Seeback effect is used in thermocouple. 95. What are the various types of the thermometers? Copper-Constantan, Iron-Constantan, Constantan & Chromal-Alumel. Platinum-Rhodium, Chromal-

96. What is the purpose of protecting tube in a thermocouple? It is used to protect the thermocouple from harmful atmosphere, corrosive fluids and also to prevent from mechanical damage. 97. Explain the principle of operation of thermistor? They have negative temperature coefficient of resistance i.e. with increase in temperature the resistance decreases and vice-versa. 98. What is the drawback in two wire RTD? Two wire RTDs will give a large lead wire & hence it is impossible for accurate measurement of temperature. 99. Give some of the temperature instruments? Resistance thermometer. Thermocouple. Thermistor. 100. Define Barometric effect? The effect due to change in atmospheric pressure is known as Barometric effect.

101.How Barometric error can be minimized? It can be minimized by keeping the filled system at a pressure sufficiently larger then the atmospheric pressure. 102. What are the advantages of Filled system Thermometer? Low cost. Less maintenance requirement. Rugged construction. Absence of need of electric power. 103. List some of the disadvantages of bimetallic thermometers. Possibility of calibration change due to rough handling. Limitation to local mainting. Availability of indication type only.

104. Define first law of thermocouple. The thermal emf of a thermocouple with junctions at T1 and T2 is totally unaffected by temperature elsewhere in the circuit if two metals used are each homogenous. 105.What are the two types of signal conditioning? a) Analog b) Digital 106. What are the possible ways of signal conditioning? A Linearisation b. Conversion c. signal transmission. D. Digital interface. 107. Define heat radiation? When radiation. a body is heated , it emits thermal energy known as heat

108. Define pyrometry . Pyrometry is the technic for measuring the bodys temperature by measuring its electromagnetic radiation. 109. What are the two types of pyrometer ? a. Radiation pyrometer b. optical pyrometer.

110. Give the values of temperature coefficient of resistance in platinum and nickel? Pt-0.004 , Ni 0.005 111. What is the advantage of optical pyrometer? It is used to measure high temperature.

112. How the calibration is adjusted in optical pyrometer? By adjusting the emissivity. 113. What are the errors in total radiation pyrometer?

a. They are senstiue to emittence errors. b. Sensitiue to any obstructions pyrometer and the hot body. 114. List some of the applications of 1. use for moving target. 2. Used in furnaces. 115. What are the advantages of total radiation pyrometer? 1. High temperature measurement. in the line of sight between the

total radiation pyrometer?

2. Fast response speed. 3.Moduate cost and high output. 3. used for the temperatures above the of thermocouple. practical operating range

116. What are the advantages of selected radiation pyrometer? The transmission losses are minimised and accuracy is improved. 117. What are the types of two colour pyrometer? a) Selected radiation pyrometer b) broad band pyrometer c) Chopper broad- band pyrometer d) Narrow band radiation pyrometer. 118. What is the other name for two colour radiation pyrometer? Ratio pyrometer.

119. What are the advantages in ratio pyrometer? 1. Less accurate 2. More cost about 50-100% more than other types of pyrometer. 120. What are the disadvantages of total radiation pyrometer? 1. Non linear scale. 2. Emissivity of target material affecting measurement. 3.Errors due to presence of gases and vapours.

ESSAY QUESTIONS
1. With neat diagram, explain the thermal power plant? 2.With neat diagram, explain hydal power plant? 3. With neat diagram, explain the nuclear power plant? 4.With neat diagram, explain the tidal power plant? 5.With neat diagram, explain the thermo electric power plant?

6.What are tachometers? tachogenerator used for speed measurement.

Describe with neat sketch, the ac

& dc

7. Explain in detail the mechanical disk type and flash light stroboscope 8. With neat diagram, explain the mechanical behavior of a seismic instrument 9.Explain in detail float type densitometers. 10.With neat sketches, explain the principle and working of the following. (I) piezoelectric pressure transducer pressure head type densitometer 11. What are the different types of filled system thermometers? Explain the construction and working in detail.

12.With neat sketches, explain the different types of manometers.

13.What are the different electrical methods of temperature measurements? Explain any two methods in detail.
14.What are bimetallic thermpmeters? Explain the construction & working of different bimetallic thermometers? 15.With a neat diagram, explain 2 laed wire, 3 lead wire & 4 lead wire RTD measuring circuits.

16.Explain the principle of the thermocouple. Mention its types. What are the ranges of temperature for each. 17 .Explain the construction & measuring principle of total & selective radiation pyrometers. 18 . Explain the constructional features of a two color radiation pyrometer system& explain how it is used for temperature measurement ?What is the prime advantage of this pyrometer in comparison to other pyrometers? 19.How we control the steam in boiler? 20.Explain the construction & measuring principle of electrical parameters? 21.Explain the construction & measuring principle of non electrical parameters?