Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Interview Questions: Pump, Boiler, Heat Exchanger, High Pressure Vessels Conyars

Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 8

Interview Questions

Introduce yourself ?
Why SNGPL?
Why government sector ?
Gears
Yield strength
Welding
pump,
boiler,
Heat Exchanger,
High Pressure Vessels
Conyars

1. What is the difference between scavenging and supercharging ?


Ans: Scavenging is process of flushing out burnt gases from engine cylinder by introducing
fresh air in the cylinder before exhaust stroke ends. Supercharging is the process of supplying
higher mass of air by compressing the atmospheric air.

2. What are the names given to constant temperature, constant pressure, constant volume,
constant internal energy, constant enthalpy, and constant entropy processes.
Ans: Isothermal, isochroic, isobaric, free expression, throttling and adiabatic processes
respectively.

3. In a Rankine cycle if maximum steam pressure is increased keeping steam temperature and
condenser pressure same, what will happen to dryness fraction of steam after expansion ?
Ans: It will decrease.

4. Why entropy change for a reversible adiabatic process is zero ?


Ans: Because there is no heat transfer in this process.

5. What are two essential conditions of perfect gas ?


Ans: It satisfies equation of state and its specific heats are constant.

6. Enthalpy and entropy are functions of one single parameter. Which is that ?
Ans: Temperature.

7. Why rate of condensation is higher on a polished surface compared to rusty surface ?


Ans: Polished surface promotes drop wise condensation and does not wet the surface.

8. How much resistance is offered to heat flow by drop wise condensation ?


Ans: Nil

1. Explain the second law of thermodynamics.


The entropy of the universe increases over time and moves towards a maximum value.

2. What kinds of pipes are used for steam lines?


Normally galvanized pipes are not used for steam. Mild steel with screwed or welded fittings
are the norm. Pressure and temperature are very important factors to be considered in what
type of materials to be used. Steam even at low pressures can be extremely dangerous.

3. What is the difference between shear center flexural center of twist and elastic
center?
The shear center is the centroid of a cross-section. The flexural center is the center of twist,
which is the point on a beam that you can add a load without torsion. The elastic center is
located at the center of gravity. If the object is homogeneous and symmetrical in both
directions of the cross-section then they are all equivalent.

4. What is ferrite?
Magnetic iron rock

5. What is the difference between projectile motion and a rocket motion?


A projectile has no motor/rocket on it, so all of its momentum is given to it as it is launched.
An example of a projectile would be pen that you throw across a room.
A rocket or missile does have a motor/rocket on it so it can accelerate itself while moving
and so resist other forces such as gravity.

6. What is a cotter joint?


These types of joints are used to connect two rods, which are under compressive or tensile
stress. The ends of the rods are in the manner of a socket and shaft that fit together and
the cotter is driven into a slot that is common to both pieces drawing them tightly together.
The tensile strength of the steel is proportionate to the strength needed to offset the stress
on the material divided by the number of joints employed.

7. What is the alloy of tin and lead?


A tin and lead alloy is commonly called solder. Usually solder is a wire with a rosin core used
for soldering. The rosin core acts as a flux.

8. What does F.O.F. stand for in piping design?


FOF stands for Face of Flange. A flange has either of the two types of faces:
a) Raised face
b) Flat face
The F.O.F is used to know the accurate dimension of the flange in order to avoid the minute
errors in measurement in case of vertical or horizontal pipelines.

9. Explain Otto cycle.


Otto cycle can be explained by a pressure volume relationship diagram. It shows the
functioning cycle of a four stroke engine. The cycle starts with an intake stroke, closing the
intake and moving to the compression stroke, starting of combustion, power stroke, heat
exchange stroke where heat is rejected and the exhaust stroke. It was designed by Nicolas
Otto, a German engineer.

10. What is gear ratio?


It is the ratio of the number of revolutions of the pinion gear to one revolution of the idler
gear.

11. What is annealing?


It is a process of heating a material above the re-crystallization temperature and cooling
after a specific time interval. This increases the hardness and strength if the material.

12. What is ductile-brittle transition temperature?


It is the temperature below which the tendency of a material to fracture increases rather
than forming. Below this temperature the material loses its ductility. It is also called Nil
Ductility Temperature.

13. What is a uniformly distributed load?


A UDL or uniformly distributed load is a load, which is spread over a beam in such a way
that each unit length is loaded to the same extent.

14. What are the differences between pneumatics and hydraulics?


a) Working fluid: Pneumatics use air, Hydraulics use Oil
b) Power: Pneumatic power less than hydraulic power
c) Size: P components are smaller than H components
d) Leakage: Leaks in hydraulics cause fluid to be sticking around the components. In
pneumatics, air is leaked into the atmosphere.
e) Pneumatics obtain power from an air compressor while hydraulics require a pump
f) Air is compressible, hydraulic oil is not

15. What is enthalpy?


Enthalpy is the heat content of a chemical system.

16. What is a positive displacement pump?


A positive displacement pump causes a liquid or gas to move by trapping a fixed amount of
fluid or gas and then forcing (displacing) that trapped volume into the discharge pipe.
Positive displacement pumps can be further classified as either rotary-type (for example the
rotary vane) or lobe pumps similar to oil pumps used in car engines. These pumps give a
non-pulsating output or displacement unlike the reciprocating pumps. Hence, they are called
positive displacement pumps.

17. Why would you use hydraulics rather than pneumatics?


Hydraulics is suitable for higher forces & precise motion than pneumatics. This is because
hydraulic systems generally run at significantly higher pressures than pneumatics systems.
Movements are more precise (repeatable) because hydraulics uses an incompressible liquid
to transfer power whilst pneumatics uses gases.
Pneumatic systems have some advantages too. They are usually significantly cheaper than
hydraulic systems, can move faster (gas much less viscous than oil) and do not leak oil if
they develop a leak.

18. What is isometric drawing?


It is a 3-D drawing used by draftsmen, architects etc

19. What are the advantages of gear drive?


In general, gear drive is useful for power transmission between two shafts, which are near
to each other (at most at 1m distance). In addition, it has maximum efficiency while
transmitting power. It is durable compare to other such as belts chain drives etc. You can
change the power to speed ratio.
Advantages: -
It is used to get various speeds in different load conditions.
It increases fuel efficiency.
Increases engine efficiency.
Need less power input when operated manually.

20. Which conducts heat faster steel copper or brass?


Copper conducts heat faster than steel or brass. Any material that is good for conducting
heat is also good for electricity in most cases. Wood terrible for transferring heat thus is
also insulator for electric.

21. How pipe flanges are electrically insulated?


Pipe flanges are protected from corrosion by means of electrolysis, with dielectric flanges.
The piping system is electrically insulated by what is called a sacrificial anode. A bag of
readily corrodible metal is buried in the ground with a wire running from the pipe to the bag
so that the sacrificial anode will corrode first. If any electrical current charges the pipe, it
also serves as a ground.

22. What is a Process Flow Diagram?


A Process Flow Diagram (or System Flow Diagram) shows the relationships between the
major components in the system. It also has basic information concerning the material
balance for the process.

23. Where pneumatic system is used?


Any system needs redundancy in work needs pneumatics, because the compressor of the
pneumatic system has periodical operations (intermittent work, not as hydraulic pump). The
compressed air could be accumulated in tanks with high pressures and used even if the
compressor failed.

24. Why gas containers are mostly cylindrical in shape?


The most efficient shape for withstanding high pressure is a sphere but that would be costly
to manufacture. A cylinder with a domed top and a domed bottom (look underneath, the flat
base is actually welded around the outside, the bottom of the gas container is actually
domed) is a much cheaper shape to manufacture whilst still having good strength to resist
the internal gas pressure.

25. How is martensite structure formed in steel?


Martensite transformation begins when austenite is cooled below a certain critical
temperature, called the matrensite start temperature. As we go below the martensite start
temperature, more and more martensite forms and complete transformation occurs only at
a temperature called martensire finish temperature. Formation of martensite requires that
the austenite phase must be cooled rapidly.

26. What is an ortographic drawing?


Orthographic projections are views of a 3D object, showing 3 faces of it. The 3 drawings are
aligned so that if the page were folded, it would create part of the shape. It is also called
multiview projections.
The 3 faces of an object consist of its plan view, front view and side view. There are 2 types
of orthographic projection, which are 1st angle projection and 3rd angle projection.

27. What is representative elementary volume?


Smallest volume over which measurements can be made that will yield a representative of
the whole.

28. Why are LNG pipes curved?


LNG pipes are curved because LNG is condensed gas (-164 deg cel) so it can expand the
pipes that is what engineers designed the LNG pipes are curve type.

29. What does angular momentum mean?


Angular momentum is an expression of an objects mass and rotational speed.
Momentum is the velocity of an object times it is mass, or how fast something is moving
how much it weigh. Therefore, angular momentum is the objects mass times the angular
velocity where angular velocity is how fast something is rotating expressed in terms like
revolutions per minute or radians per second or degrees per second.

30. Can you use motor oil in a hydraulic system?


Hydraulic fluid has to pass a different set of standards than motor oil. Motor oil has
tackifiers, lower sulfur content, and other ingredients that could prove harmful to the seals
and other components in a hydraulic system. If it is an emergency only should you do it.

31. What causes white smoke in two stroke locomotive engines?


That is the engine running too lean (lack of fuel). This condition will lead to overheating and
failure of the engine.
32. What is the role of nitrogen in welding?
Nitrogen is used to prevent porosity in the welding member by preventing oxygen and air
from entering the molten metal during the welding process. Other gases are also used for
this purpose such as Argon, Helium, Carbon Dioxide, and the gases given off when the flux
burns away during SMAW (stick) welding.

33. What does Green field project mean?


Green field projects are those projects, which do not create any environmental nuisance
(pollution), follows environmental management system and EIA (environment impact
assessment). These projects are usually of big magnitude.

34. Is it the stress that, produces strain or strain produces stress?


A Force applied to an object will cause a displacement. Strain is effectively a measure of this
displacement (change in length divided by original length).
Stress is the Force applied divided by the area it is applied. (E.g. pounds per square inch)
Therefore, to answer the question, the applied force produces both Stress and Strain.
Stress and Strain are linked together by various material properties such as Poisson's ratio
and Young's Modulus.

35. How does iron ore turn into steel?


To make Steel, Iron Ore is refined into iron and all the carbon is burned away using very
high heat (Bessemer). A percentage of Carbon (and other trace elements) are added back
to make steel. 36. What is knurling?
Knurling is a machining process normally carried our on a centre lathe. The act of Knurling
creates a raised criss-cross pattern on a smooth round bar that could be used as a handle or
something that requires extra grip.

37. What is the mechanical advantage of a double pulley?


It only takes half the effort to move an object but twice the distance.

38. What is extrued aluminum?


Extrusion is the process where a metal or a metal bar is pulled through a mandrel to
elongate it and/or give it a final shape.
Extruded Aluminum is a common form of making small aluminum wire, bars or beams and
many varieties of small non-structural, decorative pieces.

39. What is a Newtonian fluid?


A Newtonian fluid possesses a linear stress strain relationship curve and it passes through
the origin. The fluid properties of a Newtonian fluid do not change when any force acts upon
it.

40. What are the points in the stress strain curve for steel?
Proportional limit, elastic limit or yield point, ultimate stress and stress at failure.

You might also like